Search Results

Search found 3489 results on 140 pages for 'tcp'.

Page 54/140 | < Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >

• Why does '~$ nc -z T43 1-1024' not produce any output although '~$ ping T43' is successful?

  - by user43816

  Why does '~$ nc -z T43 1-1024' not produce any output although '~$ ping T43' is successful? '~$ nc -z -v T43 1-1024' prints 'Connection to T43 22 port [tcp/ssh] succeeded!' and 'nc: connect to T43 port 1000 (tcp) failed: Connection refused.' 'man nc': "PORT SCANNING: It may be useful to know which ports are open and running services on a target machine. The -z flag can be used to tell nc to report open ports, rather than initiate a connection. For example: '$ nc -z host.example.com 20-30'.

  Read the article

• iptables firewall to protect against automated entries

  - by Kenyana

  I am getting unusually large calls on my app. I have implemented CSRF Check over ajax and its working but am still getting so many calls. My guess is that someone has a script that is 'logged' in and making all these calls. Could someone please share a good iptables script for blocking ip's that run 10 calls to /controler/action in a second. I am using `/sbin/iptables -A INPUT -p tcp --syn --dport $port -m connlimit --connlimit-above N -j REJECT --reject-with tcp-reset save the changes see iptables-save man page, the following is redhat and friends specific command service iptables save` That is from cyberciti

  Read the article

• Cisco adaptive security appliance is dropping packets where SYN flag is not set

  - by Brett Ryan

  We have an apache instance sitting inside our DMZ which is configured to proxy requests to an internal NATed tomcat instance inside our network. It works fine, but then all of a sudden requests from apache to the tomcat instance stop getting through with the following in the apache logs: [error] (70007)The timeout specified has expired: ajp_ilink_receive() can't receive header Investigating into the Cisco log viewer reveals the following: Error Message %ASA-6-106015: Deny TCP (no connection) from IP_address/port to IP_address/port flags tcp_flags on interface interface_name. Explanation The adaptive security appliance discarded a TCP packet that has no associated connection in the adaptive security appliance connection table. The adaptive security appliance looks for a SYN flag in the packet, which indicates a request to establish a new connection. If the SYN flag is not set, and there is not an existing connection, the adaptive security appliance discards the packet. Recommended Action None required unless the adaptive security appliance receives a large volume of these invalid TCP packets. If this is the case, trace the packets to the source and determine the reason these packets were sent. All are machines are virtualised using VMware, and by default machines have been using the Intel E1000 emulated NIC. Our network administrator has changed this to a VMXNET3 driver in an attempt to correct the problem, we just have to wait and see if the problem persists as it's an intermittent problem. Is there something else that could be causing this problem? This isn't the first service where we have had similar issues. Our apache host is running Ubuntu 11.10 with a kernel version of 3.0.0-17-server. We have also had this issue on RHEL5 (5.8) running kernel 2.6.18-308.16.1.el5, this machine also has the E1000 NIC. NOTE: I am not a network administrator and am a software architect and analyst programmer responsible for these systems.

  Read the article

• Error 720 on VPN (PPTP) attempt

  - by Andy Shulman

  When I attempt to connect to a server running XP x64 (so essentially Server 2003) using a PPTP connection, it fails with client-side error Registering your computer on the network... Error 720: A connection to the remote computer could not be established. You might need to change the network settings for this configuration. and server-side error Event ID: 20050 The user WINSERV3\Andy connected to port VPN8-1 has been disconnected because no network protocols were successfully negotiated. I have configured the router to pass both TCP packets on 1723 and GRE packets. I have used Wireshark (filtering out ARP, UDP, and all TCP ports other than 1723) to observe the packets received by the server. Wireshark does not explicitly name any protocol GRE, but it does tell me the server sent and received TCP, PPTP, PPP LCP, PPP CHAP, PPP CBCP, and PPP IPCP. The connection seems to go wrong at packet 30, where the protocol is PPP LCP, with the payload of the packet being labeled "Protocol Reject". Obviously, this is going from server to client. This would seem to lead to the conclusion that there is something wrong with my client, which runs Windows 7 Ultimate x64. However, it is able to connect to my house's router, which runs the DD-WRT firmware and is thus a PPTP endpoint. I'm thoroughly at a loss. Please help!

  Read the article

• ipvsadm lists a few hosts by IP only, rest by name

  - by dmourati

  We use keepalived to manage our Linux Virtual Server (LVS) load balancer. The LVS VIPs are setup to use a FWMARK as configured in iptables. virtual_server fwmark 300000 { delay_loop 10 lb_algo wrr lb_kind NAT persistence_timeout 180 protocol TCP real_server 10.10.35.31 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.31" misc_timeout 30 } } real_server 10.10.35.32 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.32" misc_timeout 30 } } real_server 10.10.35.33 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.33" misc_timeout 30 } } real_server 10.10.35.34 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.34" misc_timeout 30 } } } http://www.austintek.com/LVS/LVS-HOWTO/HOWTO/LVS-HOWTO.fwmark.html [root@lb1 ~]# iptables -L -n -v -t mangle Chain PREROUTING (policy ACCEPT 182G packets, 114T bytes) 190M 167G MARK tcp -- * * 0.0.0.0/0 w1.x1.y1.4 multiport dports 80,443 MARK set 0x493e0 62M 58G MARK tcp -- * * 0.0.0.0/0 w1.x1.y2.4 multiport dports 80,443 MARK set 0x493e0 [root@lb1 ~]# ipvsadm -L IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn FWM 300000 wrr persistent 180 -> 10.10.35.31:0 Masq 24 1 0 -> dis2.domain.com:0 Masq 24 3 231 -> 10.10.35.33:0 Masq 24 0 208 -> 10.10.35.34:0 Masq 24 0 0 At the time the realservers were setup, there was a misconfigured dns for some hosts in the 10.10.35.0/24 network. Thereafter, we fixed the DNS. However, the hosts continue to show up as only their IP numbers (10.10.35.31,10.10.35.33,10.10.35.34) above. [root@lb1 ~]# host 10.10.35.31 31.35.10.10.in-addr.arpa domain name pointer dis1.domain.com. OS is CentOS 6.3. Ipvsadm is ipvsadm-1.25-10.el6.x86_64. kernel is kernel-2.6.32-71.el6.x86_64. Keepalived is keepalived-1.2.7-1.el6.x86_64. How can we get ipvsadm -L to list all realservers by their proper hostnames?

  Read the article

• Why does my Belkin wireless router has eMule port open?

  - by Jeremy Powell

  I have a Belkin F6D4230-4 v1 router. When I port scan it with nmap I get the following: $ sudo nmap -sS -A -T5 192.168.2.1 -p- Starting Nmap 5.00 ( http://nmap.org ) at 2010-04-17 11:40 CDT Interesting ports on 192.168.2.1: Not shown: 65532 closed ports PORT STATE SERVICE VERSION 80/tcp open http Belkin 2307 wifi router http config (IP_SHARER httpd 1.0) |_ html-title: '+i1+' 4661/tcp filtered unknown 4662/tcp filtered edonkey MAC Address: 00:22:75:5D:52:D8 (Belkin International) Device type: WAP|broadband router|firewall|printer|specialized|webcam Running (JUST GUESSING) : Linksys embedded (95%), TRENDnet embedded (95%), Netgear embedded (92%), Canon embedded (89%), On Time RTOS (89%), Symantec embedded (89%), D-Link embedded (86%), Polycom embedded (85%) Aggressive OS guesses: Linksys WRT54GC or TRENDnet TEW-431BRP wireless broadband router (95%), TRENDnet TW100-BRF114 broadband router (95%), Netgear FR114P ProSafe VPN firewall (92%), Canon PIXMA MX850 printer (89%), On Time RTOS (89%), Symantec Firewall/VPN 100 (89%), D-Link DI-714P+ wireless broadband router (86%), Polycom ViewStation video conferencing system (85%) No exact OS matches for host (test conditions non-ideal). Network Distance: 1 hop Service Info: Device: WAP OS and Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 21.57 seconds Why are the 4461 and 4462 ports open? This is a basic, out-of-the-box installation.

  Read the article

• mysql master-master setup as a way to simply master-slave promotion

  - by Chris Go

  I'm trying to see if the following plan is viable. Goal here is to be able to do HA (uptime) and not necessarily for load -- writes are fine on one MySQL 5.5 server (with innodb) but not really possible when the database is down. Currently, I have a master-slave replication setup which works fine except it doesn't have automatic promotion (obviously). what I am planning on doing is setup master-master replication to possibly do this "automatic promotion" using Amazon Route 53 DNS Failover (Health checks). What I am trying to avoid is to NOT have to do the auto-increment trick because the "business folks" got used to the auto-incrementing PK as consecutive numbers (yeah, I know this is bad but data is from 2004). So, setup the master-master replication WITHOUT the auto-increment collision prevention bit. The primary master is db1.domain.com and secondary master is db2.domain.com In Amazon Route 53, setup DNS Failover record for db.domain.com - primary failover is db1.domain.com - with a TCP healthcheck on IP address port 3306 - secondary failover is db2.domain.com - with a TCP healthcheck on IP address port 3306 Most of the time (99%), unless tcp://db1.domain.com:3306 is dead, db1.domain.com will be served up on DNS hits to db.domain.com. In fact, hopefully this is 100%. The possible downsides of this is the loss of a primary key (collision) and I think I am OK with losing one order. We are a low data volume B2B business and can just call our client up if this occurs (like an order disappearing). Does this sound like a good plan? Then I will also run another slave replication on db1.domain.com as "master" to a slave-db1.domain.com -- not sure why, maybe for heavy SELECTs?

  Read the article

• Fortinet: Is there any equivalent of the ASA's packet-tracer command?

  - by Kedare

  I would like to know if there is not Fortigates an equivalent of the packet-tracer command that we can find on the ASA. Here is an example of execution for those who don't know it: NAT and pass : lev5505# packet-tracer input inside tcp 192.168.3.20 9876 8.8.8.8 80 Phase: 1 Type: ACCESS-LIST Subtype: Result: ALLOW Config: Implicit Rule Additional Information: MAC Access list Phase: 2 Type: ROUTE-LOOKUP Subtype: input Result: ALLOW Config: Additional Information: in 0.0.0.0 0.0.0.0 outside Phase: 3 Type: ACCESS-LIST Subtype: log Result: ALLOW Config: access-group inside-in in interface inside access-list inside-in extended permit tcp any any eq www access-list inside-in remark Allows DNS Additional Information: Phase: 4 Type: IP-OPTIONS Subtype: Result: ALLOW Config: Additional Information: Phase: 5 Type: VPN Subtype: ipsec-tunnel-flow Result: ALLOW Config: Additional Information: Phase: 6 Type: NAT Subtype: Result: ALLOW Config: object network inside-network nat (inside,outside) dynamic interface Additional Information: Dynamic translate 192.168.3.20/9876 to 81.56.15.183/9876 Phase: 7 Type: IP-OPTIONS Subtype: Result: ALLOW Config: Additional Information: Phase: 8 Type: FLOW-CREATION Subtype: Result: ALLOW Config: Additional Information: New flow created with id 94755, packet dispatched to next module Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: allow Blocked by ACL: lev5505# packet-tracer input inside tcp 192.168.3.20 9876 8.8.8.8 81 Phase: 1 Type: ROUTE-LOOKUP Subtype: input Result: ALLOW Config: Additional Information: in 0.0.0.0 0.0.0.0 outside Phase: 2 Type: ACCESS-LIST Subtype: Result: DROP Config: Implicit Rule Additional Information: Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: drop Drop-reason: (acl-drop) Flow is denied by configured rule Is there any equivalent on the Fortigates ?

  Read the article

• NAT, iptables and problematic ports

  - by Rajie

  I am building a small office network with virtual machines. My schema is this: Computer A: gateway, ip 1.1.1.1, iptables used for NAT [eth0=public internet dhcp, dhcp; eth1=gateway] Computer B: client, ip 1.1.1.2, using gateway from Computer A. NAT is working, and Computer B can access the internet using the A's gateway. I redirected some incoming ports from A to B (for instance, if A receives a request to port 80, it goes automatically to Computer B's Apache). The thing is that I do not really understand how to open/close ports for Computer B from Computer A. I know how to close a port: iptables -A INPUT -p tcp --dport 80 -j DROP And it will refuse all incoming (not output) connections to port 80. However, this works for main interface eth0. I tried to, for instance, drop ingoing and outgoing connections for Computer B, port 80: iptables -A FORWARD -i eth1 -o eth0 -p tcp --dport 80 -j DROP iptables -A FORWARD -i eth0 -o eth1 -p tcp --dport 80 -j DROP But it does not work. And I cannot figure out what I am doing wrong. Any clue?

  Read the article

• Apache2, making my site publicly available

  - by Shackler

  Hello, I want to make my apache 2 development server public to the internet, it is a Django based website. Here is my apache2 config: <VirtualHost *:80> Alias /media /home/user/myproject/statics Alias /admin_media /home/myuser/django/Django-1.1.1/django/contrib/admin/media WSGIScriptAlias / /home/myuser/myproject/myproject_wsgi.py WSGIDaemonProcess myproject user=myuser group=myuser threads=25 WSGIProcessGroup myproject </VirtualHost> When I do netstat -lntup I get: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN - tcp6 0 0 :::80 :::* LISTEN - tcp6 0 0 :::22 :::* LISTEN - tcp6 0 0 ::1:631 :::* LISTEN - udp 0 0 0.0.0.0:5353 0.0.0.0:* - udp 0 0 0.0.0.0:38582 0.0.0.0:* I connect with ADSL thus I am behind a router. For this I have made my computer DMZ enabled to my machine. What can be the problem? When I try to login with my ip, I get my routers config page, when a friend tries to connect to me from internet, he gets "not authorized".

  Read the article

• pfsense 2.0.1 Firewall SMB Share not showing up under network

  - by atrueresistance

  I have a freenas NAS with a SMB share running at 192.168.2.2 of a 192.168.2.0/28 network. Gateway is 192.168.2.1. Originally this was running on a switch with my LAN, but now having upgraded to new hardware the Freenas has it's own port on the firewall. Before the switch the freenas would show up under Network on a windows 7 box and an OSX Lion box as freenas{wins} or CIFS shares on freenas{osx} so I know it doesn't have anything do to with the freenas. Here are my pfsense rules. ID Proto Source Port Destination Port Gateway Queue Schedule Description PASS TCP FREENAS net * LAN net 139 (NetBIOS-SSN) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 389 (LDAP) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 445 (MS DS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 137 (NetBIOS-NS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 138 (NetBIOS-DGM) * none cifs lan passthrough BLOCK * FREENAS net * LAN net * * none BLOCK * FREENAS net * OPTZONE net * * none BLOCK * FREENAS net * 192.168.2.1 * * none PASS * FREENAS net * * * * none BLOCK * * * * * * none I can connect if I use \\192.168.2.2 and enter the correct login details. I would just like this to show up on the network. Nothing in the log seems to be blocked when I filter by 192.168.2.2. What port am I missing for SMB to show up under the network and not have to connect by IP? ps. Do I really need the LDAP rule?

  Read the article

• WAMP server not starting and a mystery service is using port 80

  - by David Gard

  I'm using WAMP on Windows 7 and tonight I'm unable to start it (it's been working fine for about 3 years previously). I first checked the logs, but nothing in there. So I checked the Windows Event Viewer (eventvwr), where I saw 2x errors for each attempted start - The Apache service named reported the following error: (OS 10048)Only one usage of each socket address (protocol/network address/port) is normally permitted. : make_sock: could not bind to address 0.0.0.0:80. The Apache service named reported the following error: no listening sockets available, shutting down. After this, I opened the command prompt and ran netstat -a, and to my surprise there were 3 entries for port 80 - Prot   Local Address  Foreign Address   State TCP   127.0.0.1:80       MyPCName:53831   TIME_WAIT TCP   127.0.0.1:80       MyPCName:57834   TIME_WAIT TCP   127.0.0.1:80       MyPCName:57839   TIME_WAIT From here, I'm kind of lost. As far as I can tell, something is utalising port 80, but I don't know what or why. If anyone is able to suggest what I might do next I'd be most greatful. Thanks.

  Read the article

• Error applying iptables rules using iptables-restore

  - by John Franic

  Hi I'm using Ubuntu 9.04 on a VPS. I'm getting an error if I apply a iptables rule. Here is what I have done. 1.Saved the existing rules iptables-save /etc/iptables.up.rules Created iptables.test.rules and add some rules to it nano /etc/iptables.test.rulesnano /etc/iptables.test.rules This is the rules I added *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 22- j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT After editing when I try to apply the rules by iptables-restore < /etc/iptables.test.rules I get the following error iptables-restore: line 42 failed Line 42 is COMMIT and I comment that out I get iptables-restore: COMMIT expected at line 43 I'm not sure what is the problem, it is expecting COMMIT but if COMMIT is there it's giving error. Could it be due to the fact i'm usin a VPS?My provider using OpenVZ for virtualizaton.

  Read the article

• using pf for packet filtering and ipfw's dummynet for bandwidth limiting at the same time

  - by krdx

  I would like to ask if it's fine to use pf for all packet filtering (including using altq for traffic shaping) and ipfw's dummynet for bandwidth limiting certain IPs or subnets at the same time. I am using FreeBSD 10 and I couldn't find a definitive answer to this. Googling returns such results as: It works It doesn't work Might work but it's not stable and not recommended It can work as long as you load the kernel modules in the right order It used to work but with recent FreeBSD versions it doesn't You can make it work provided you use a patch from pfsense Then there's a mention that this patch might had been merged back to FreeBSD, but I can't find it. One certain thing is that pfsense uses both firewalls simultaneously so the question is, is it possible with stock FreeBSD 10 (and where to obtain the patch if it's still necessary). For reference here's a sample of what I have for now and how I load things /etc/rc.conf ifconfig_vtnet0="inet 80.224.45.100 netmask 255.255.255.0 -rxcsum -txcsum" ifconfig_vtnet1="inet 10.20.20.1 netmask 255.255.255.0 -rxcsum -txcsum" defaultrouter="80.224.45.1" gateway_enable="YES" firewall_enable="YES" firewall_script="/etc/ipfw.rules" pf_enable="YES" pf_rules="/etc/pf.conf" /etc/pf.conf WAN1="vtnet0" LAN1="vtnet1" set skip on lo0 set block-policy return scrub on $WAN1 all fragment reassemble scrub on $LAN1 all fragment reassemble altq on $WAN1 hfsc bandwidth 30Mb queue { q_ssh, q_default } queue q_ssh bandwidth 10% priority 2 hfsc (upperlimit 99%) queue q_default bandwidth 90% priority 1 hfsc (default upperlimit 99%) nat on $WAN1 from $LAN1:network to any -> ($WAN1) block in all block out all antispoof quick for $WAN1 antispoof quick for $LAN1 pass in on $WAN1 inet proto icmp from any to $WAN1 keep state pass in on $WAN1 proto tcp from any to $WAN1 port www pass in on $WAN1 proto tcp from any to $WAN1 port ssh pass out quick on $WAN1 proto tcp from $WAN1 to any port ssh queue q_ssh keep state pass out on $WAN1 keep state pass in on $LAN1 from $LAN1:network to any keep state /etc/ipfw.rules ipfw -q -f flush ipfw -q add 65534 allow all from any to any ipfw -q pipe 1 config bw 2048KBit/s ipfw -q pipe 2 config bw 2048KBit/s ipfw -q add pipe 1 ip from any to 10.20.20.4 via vtnet1 out ipfw -q add pipe 2 ip from 10.20.20.4 to any via vtnet1 in

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• NAT ports - how do they work?

  - by Davidoper

  I have the following network schema: Computer A: three nics: NIC 1 (eth0): dhcp, public internet NIC 2 (eth1): static 192.168.1.1, gateway for Computer B NIC 3 (eth2): static 192.168.2.1, gateway for Computer C Computer B: static 192.168.1.2, using gateway 192.168.1.1 (NIC 2). Computer C: static 192.168.2.2, using gateway 192.168.2.1 (NIC 3). So I applied this to get NAT working: iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE Every computer can connect to the internet now. I have been applying rules to the main computer (Computer A), like dropping connections to some ports, e.g ssh: iptables -A INPUT -p tcp --dport 22 -j DROP But for instance, now I would like only allow connections for ports 20,21,22,53 and 80 in Computer C, and ignore the outside traffic if it's not related to those ports. The allowed connections should be FROM Computer C to outside, but not from outside to Computer C (I mean - Computer C is not hosting any HTTP or SSH, but it is going to use them as a client). I guess this sould be done like this: iptables -A OUTPUT -i eth2 -o eth0 -p tcp --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth2 -o eth0 -p tcp --sport 21 -m state --state ESTABLISHED -j ACCEPT The last rule (dropping any other traffic different from those) is at the end of the configuration, so -A should be working correctly. The thing is... it is not working. If I put the last rule like this: iptables -A FORWARD -i eth2 -o eth0 -j DROP It just drops everything and, for instance, port 21 (previously opened as you can see above) is not either working. Can you tell me what could I have done wrong? I have been struggling with this problem for some time and I am unable to solve it. Thanks!

  Read the article

• Connect to Postgres remotely, open port 5432 for Postgres in iptables

  - by Victor

  I am trying to connect to Postgres remotely but I need to open port 5432 in iptables. My current iptables configuration is as follows: *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 30000 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT What would I have to add in iptables to open the port? I'm trying to install phppgadmin on a different server to access the postgres database. Thank you.

  Read the article

• How to migrate a running KVM (with full disk copy) to another node?

  - by klipz

  I'm doing tests on KVM, and I'd like to see if I can make a hot migration, I mean the virtual machine won't stop running during the migration (but a few seconds of freeze is ok). I use a small cluster for my test : kvm1, kvm2, and kvmnfs. kvm1 and kvm2 runs the virtual machines kvmnfs is a NFS server, and it's mounted on /KVM on both kvm1 and kvm2 To migrate a VM (only RAM in fact) from kvm1 to kvm2, I run the same kvm command on kvm2 (with -incoming tcp:0:4444) that on kvm1, then I use "migrate -d tcp:kvm2:4444" : It works great, since the VM file is common to both machines. Now, I wan't to make a full migration (RAM + disk) of a local VM file (no more NFS) of kvm1 to kvm2. I tried to create an empty file, with touch, on kvm2 and use the same kvm command line + the "-incoming ..."). Then on kvm1 I use "migrate -d tcp:kvm2:4444" : It copies everything, then... the VM fails (any I/O disk gives an I/O error) ! And my VM file on kvm2, the one I created with touch, as still a size of 0 bytes. What am I doing wrong ? What is the exact command to use on kvm2 ? And what is the command to launch, in the monitoring mode, on kvm1 ?

  Read the article

• best-practices to block social sites

  - by adopilot

  In our company we have around 100 workstation with internet access, And day by day situation getting more worst and worst from perspective of using internet access for the purpose of doing private jobs, and wasting time on social sites. Open hearted I am not for blocking sites like Facebook, Youtube, and others similar but day by day my colleagues do not finishing his tasks and while I looking at their monitor all time they are ruining IE or Mozilla and chat and things like that. In other way Ill like to block youtube sometime when We have very poor internet access speed, Here is my questions: Do other companies blocking social sites ? Do I need dedicated device for that like hardware firewall, super expensive router Or I can do that whit my existing FreeBSD 6.1 self made router with two lan cards and configured nat to act like router. I was trying do that using ipfw and routerfirewall but without success, My code looks like ipfw add 25 deny tcp from 192.168.0.0/20 to www.facebook.com ipfw add 25 deny udp from 192.168.0.0/20 to www.facebook. ipfw add 25 deny tcp from 192.168.0.0/20 to www.dernek. ipfw add 25 deny udp from 192.168.0.0/20 to www.dernek. ipfw add 25 deny tcp from 192.168.0.0/20 to www.youtube. ipfw add 25 deny udp from 192.168.0.0/20 to www.youtube.com

  Read the article

• MS SQL Server Firewall Ports

  - by mmacaulay

  Hi, I've recently found myself in the position of quickly deploying a production app on SQL Server 2008 (EXPRESS), and I've been having some issues with configuring firewall rules between our web server running the ASP.NET app and our database server. Everything that I can find on the internet claims that I should only need to have TCP ports 1433/1434 and UDP port 1434 accessible on the database server. However, we were unable to get connectivity going between the web app and the database with just those ports. With the help of one of the guys in our datacentre, we discovered that there was traffic also going to TCP port 2242 on the database server. After opening this port, everything worked, but we're not sure why. Later on, I had to reinstall SQL Server due to some disk space issues, and found that the problem had resurfaced - after another session with the packet sniffer, we discovered that this time traffic was going to TCP port 4541 on the database server. My question is, is there some configuration option that I'm missing in SQL server that's making it choose random ports? I'd like to have our firewall rules locked down as much as possible, and of course we'd like to avoid any future mysterious connectivity issues, especially once the app is live. Both servers are running Windows 2003 R2 X64.

  Read the article

• Firefox is very slow when establish SSL sessions

  - by yanglei

  Using wireshark, I discovered that Firefox v3.0 gets stuck every time before "client key exchange, change cipher spec" stage when establishing a SSL session. Specifically, it takes 0.8~1.8 second before Firefox send "Client Key Exchange" request. This is unacceptable since our application is HTTPS only. I tested this on IE6 and IE8, both works well. Any clues? [Update] Finally, I found the reason of 1 ~ 2 seconds stuck by displaying all captured packets in Wireshark. After the "server hello" stage, Firefox makes a request to ocsp.verisign.com combined with an additional DNS lookup for that domain. Firefox must wait the revocation status from OCSP before entering the next stage of SSL. Depends on whether DNS cache is in effect, this process takes 1 ~ 2 seconds. A interesting observation is that the IP packet contains "client key exchange" has a high possibility to get lost and thus a TCP retransmission is necessary. When this happens, the process can take 3 seconds at worst. I'm not sure if this is a coincidence or a bug. Anyway, here is the result from Wireshark: (delta-time) 0.369296 src-ip dst-ip TCP [ACK] Seq=161 Ack=2741 Win=65340 Len=0 2.538835 src-ip dst-ip TLSv1 Client Key Exchange, Change Cipher Spec, Finished 2.987034 src-ip dst-ip TLSv1 [TCP Retransmission] Client Key Exchange, Change Cipher Spec, Finished The difference between Firefox and IE is this: Firefox 3 enables OCSP checking by default where as IE only supports it. So, there is no problem with both IE6 and IE8. This is indeed a "certificate revoke" problem. Thanks

  Read the article

• ASA Slow IPSec Performance with Inconsistent Window Size

  - by Brent

  I have a IPSec link between two sites over ASA 5520s running 8.4(3) and I am getting extremely poor performance when traffic passes over the IPSec VPN. CPU on the devices is ~13%, Memory at 408 MB, and active VPN sessions 2. The load on both of the the devices is particularly low. Latency between the two sites is ~40ms. Screenshot of wireshark file transfer between the two hosts over the firewall IPSec VPN performing at 10MBPS. Note the changing window size. http://imgur.com/wGTB8Cr Screenshot of wireshark file transfer between the two hosts over the firewall not going over IPSec performing at 55MBPS. Constant window size. http://imgur.com/EU23W1e I'm showing an inconsistent window size when transferring over the IPSec VPN ranging in 46,796 to 65535. When performing at 55+MBPS, the window size is consistently 65,535. Does this show a problem in my configuration of the IPSec VPN in the ASA or a Layer1/2 issue? Using ping xxxxxx -f -l I finally get a non-fragment at 1418 bytes so 1418+28 for IP/ICMP headers = 1446. I know that I have 1500 set on the ASA and Ethernet. I do have "Force Maximum segment size for TCP proxy connection to be" "1380" bytes set under Configuration Advanced TCP Options on the ASA. Using IPERF, I am getting a "TCP Window Full" every few seconds and ~3 MBPS performance. http://imgur.com/elRlMpY Show Run on the ASA http://pastebin.com/uKM4Jh76 Show cry accelerator stats http://pastebin.com/xQahnqK3

  Read the article

• Either, nginx+php-fpm bad config or nginx+php-fpm cannot handle high query?

  - by The Wolf

  I have wordpress installed in my server configured(hopefully with nginx+php-fpm+mariaDB). I am trying to import using wordpress importer a 1.5MB xml file. Everytime I try to upload it using the importer, it got cut of... meaning just blank screen result.. Here is my error log: actually I just posted 2 of the errors [error] 858#0: *1 connect() failed (111: Connection refused) while connecting to upstream, client: xx.xxx.xx.xx, server: xxx.com, request: "GET xxxx.html HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "xxx.com" [error] 858#0: *13 connect() failed (111: Connection refused) while connecting to upstream, client: xxx.x.xx.xx, server: xxx.com, request: "GET xxxx.php HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "xxx.com" I don't know what is the reason why it can't process the wordpress export .xml. I already increased max_file_upload & etc., but nothing happens. Hope somebody can help me. Here are my conf: nginx.conf user nginx; worker_processes 8; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; #tcp_nopush on; server_tokens off; keepalive_timeout 65; fastcgi_read_timeout 500; #gzip on; client_max_body_size 2M; php-fpm.conf ;;;;;;;;;;;;;;;;;;;;; ; FPM Configuration ; ;;;;;;;;;;;;;;;;;;;;; ; All relative paths in this configuration file are relative to PHP's install ; prefix. ; Include one or more files. If glob(3) exists, it is used to include a bunch of ; files from a glob(3) pattern. This directive can be used everywhere in the ; file. include=/etc/php-fpm.d/*.conf ;;;;;;;;;;;;;;;;;; ; Global Options ; ;;;;;;;;;;;;;;;;;; [global] ; Pid file ; Default Value: none pid = /var/run/php-fpm/php-fpm.pid ; Error log file ; Default Value: /var/log/php-fpm.log error_log = /var/log/php-fpm/error.log ; Log level ; Possible Values: alert, error, warning, notice, debug ; Default Value: notice ;log_level = notice ; If this number of child processes exit with SIGSEGV or SIGBUS within the time ; interval set by emergency_restart_interval then FPM will restart. A value ; of '0' means 'Off'. ; Default Value: 0 ;emergency_restart_threshold = 0 ; Interval of time used by emergency_restart_interval to determine when ; a graceful restart will be initiated. This can be useful to work around ; accidental corruptions in an accelerator's shared memory. ; Available Units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;emergency_restart_interval = 0 ; Time limit for child processes to wait for a reaction on signals from master. ; Available units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;process_control_timeout = 0 ; Send FPM to background. Set to 'no' to keep FPM in foreground for debugging. ; Default Value: yes daemonize = no ;;;;;;;;;;;;;;;;;;;; ; Pool Definitions ; ;;;;;;;;;;;;;;;;;;;; ; See /etc/php-fpm.d/*.conf [root@host etc]# vim php-fpm.conf [root@host etc]# vim php-fpm.conf ; Default Value: notice ;log_level = notice ; If this number of child processes exit with SIGSEGV or SIGBUS within the time ; interval set by emergency_restart_interval then FPM will restart. A value ; of '0' means 'Off'. ; Default Value: 0 ;emergency_restart_threshold = 0 ; Interval of time used by emergency_restart_interval to determine when ; a graceful restart will be initiated. This can be useful to work around ; accidental corruptions in an accelerator's shared memory. ; Available Units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;emergency_restart_interval = 0 ; Time limit for child processes to wait for a reaction on signals from master. ; Available units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;process_control_timeout = 0 ; Send FPM to background. Set to 'no' to keep FPM in foreground for debugging. ; Default Value: yes daemonize = no ;;;;;;;;;;;;;;;;;;;; ; Pool Definitions ; ;;;;;;;;;;;;;;;;;;;; ; See /etc/php-fpm.d/*.conf ps aux [root@host etc]# ps aux USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 1 0.0 0.1 2900 1380 ? Ss Jun02 0:00 init root 2 0.0 0.0 0 0 ? S Jun02 0:00 [kthreadd/9308] root 3 0.0 0.0 0 0 ? S Jun02 0:00 [khelper/9308] root 124 0.0 0.0 2464 576 ? S<s Jun02 0:00 /sbin/udevd -d root 460 0.0 0.1 35976 1308 ? Sl Jun02 0:00 /sbin/rsyslogd -i /var/run/syslogd.pid -c 5 root 474 0.0 0.0 8940 1028 ? Ss Jun02 0:00 /usr/sbin/sshd root 481 0.0 0.0 3264 876 ? Ss Jun02 0:00 xinetd -stayalive -pidfile /var/run/xinetd.pid root 491 0.0 0.1 6268 1432 ? S Jun02 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --pid-file=/var/lib/mysql/host.busilak.com. mysql 584 0.1 6.8 679072 71456 ? Sl Jun02 0:04 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --plugin-dir=/usr/lib/mysql/plugin --use root 586 0.0 0.3 12008 3820 ? Ss Jun02 0:01 sshd: root@pts/0 root 629 0.0 0.0 9140 756 ? Ss Jun02 0:00 /usr/sbin/saslauthd -m /var/run/saslauthd -a pam -n 2 root 630 0.0 0.0 9140 520 ? S Jun02 0:00 /usr/sbin/saslauthd -m /var/run/saslauthd -a pam -n 2 root 645 0.0 0.1 12788 1928 ? Ss Jun02 0:01 sendmail: accepting connections smmsp 653 0.0 0.1 12576 1728 ? Ss Jun02 0:00 sendmail: Queue runner@01:00:00 for /var/spool/clientmqueue root 691 0.0 0.1 7148 1184 ? Ss Jun02 0:00 crond root 698 0.0 0.1 6272 1688 pts/0 Ss Jun02 0:00 -bash root 1006 0.0 0.0 7828 924 ? Ss 00:30 0:00 nginx: master process /usr/sbin/nginx -c /etc/nginx/nginx.conf nginx 1007 0.0 0.1 8156 1724 ? S 00:30 0:00 nginx: worker process nginx 1008 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1009 0.0 0.1 8020 1356 ? S 00:30 0:00 nginx: worker process nginx 1011 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1012 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1013 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1014 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1015 0.0 0.1 8024 1344 ? S 00:30 0:00 nginx: worker process root 1030 0.0 0.2 25396 2904 ? Ss 00:30 0:00 php-fpm: master process (/etc/php-fpm.conf) apache 1031 0.0 1.9 40700 20624 ? S 00:30 0:00 php-fpm: pool www apache 1032 0.0 2.0 41924 21888 ? S 00:30 0:01 php-fpm: pool www apache 1033 0.0 1.9 41212 20848 ? S 00:30 0:01 php-fpm: pool www apache 1034 0.0 1.9 40956 20792 ? S 00:30 0:01 php-fpm: pool www apache 1035 0.0 2.0 41560 21556 ? S 00:30 0:02 php-fpm: pool www apache 1040 0.0 1.8 39292 19120 ? S 00:30 0:00 php-fpm: pool www root 1125 0.0 0.0 6080 1040 pts/0 R+ 01:04 0:00 ps aux netstat -l [root@host etc]# netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 *:ssh *:* LISTEN tcp 0 0 localhost.localdomain:smtp *:* LISTEN tcp 0 0 localhost.locald:cslistener *:* LISTEN tcp 0 0 *:mysql *:* LISTEN tcp 0 0 *:http *:* LISTEN tcp 0 0 *:ssh *:* LISTEN Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node Path unix 2 [ ACC ] STREAM LISTENING 60575947 /var/run/saslauthd/mux unix 2 [ ACC ] STREAM LISTENING 60574168 @/com/ubuntu/upstart unix 2 [ ACC ] STREAM LISTENING 60575873 /var/lib/mysql/mysql.sock Hope somebody can help me to figure out what is the problem.

  Read the article

• Cisco ASA 8.2 ACL For NAT

  - by javano

  Sadly I have gone back in time to ASA 8.2(5)33 which I am not so familiar with. I have configured NAT between two interfaces but traffic isn't passing becasue I can't get the ACL to work; (The full config which isn't very big is here but to keep this post tidy I have just pasted the important parts below); interface Ethernet0/0 switchport access vlan 108 ! interface Ethernet0/6 switchport access vlan 104 ! interface Ethernet0/7 switchport access vlan 105 ! interface Vlan104 description BUILDING2 nameif BUILDING2 security-level 0 ip address 10.104.0.1 255.255.255.0 ! interface Vlan105 description BUILDING1 nameif BUILDING1 security-level 0 ip address 10.105.0.1 255.255.255.0 ! interface Vlan108 description Main LAN VLAN nameif lan security-level 0 ip address 172.22.0.215 255.255.255.0 ! object-group network obj_net_Remote_Hosts network-object host 111.111.111.3 network-object host 111.111.111.65 object-group network obj_host_pc1_eth1 network-object host 10.104.0.111 object-group network obj_host_pc2_eth1 network-object host 10.104.0.112 object-group network obj_host_pc3_eth1 network-object host 10.104.0.106 object-group network obj_host_pc4_eth1 network-object host 10.104.0.107 object-group network obj_net_PCs description IPs of PCs group-object obj_host_pc1_eth1 group-object obj_host_pc2_eth1 group-object obj_host_pc3_eth1 group-object obj_host_pc4_eth1 access-list acl_NAT_pc1_91 extended permit tcp host 10.104.0.111 host 111.111.111.3 eq 8101 access-list acl_Permit_PCs extended permit tcp object-group obj_net_PCs object-group obj_net_Remote_Hosts eq 8101 ! global (BUILDING1) 11 111.111.222.91 netmask 255.255.255.255 nat (BUILDING2) 11 access-list acl_NAT_pc1_91 access-group acl_Permit_PCs in interface BUILDING2 route BUILDING1 111.111.111.3 255.255.255.255 10.105.0.2 1 route BUILDING1 111.111.111.65 255.255.255.255 10.105.0.2 1 When I try and connect from PC1 to ip 111.111.111.3 I see the following error logged on the ASA console; %ASA-2-106001: Inbound TCP connection denied from 10.104.0.111/38495 to 111.111.111.3/8101 flags SYN on interface blades What the duce!

  Read the article

• iptables-restore: line 1 failed

  - by Doug

  Hello, I am new to servers, and I was following this guide and it failed on the first command instructed. Could anyone give me a hand? http://wiki.debian.org/iptables ~ZORO~:/etc# iptables-restore < /etc/iptables.test.rules iptables-restore: line 1 failed Edit: iptables.test.rules ~ZORO~:/etc# cat /etc/iptables.test.rules *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You could modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections for script kiddies # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE -A INPUT -p tcp -m state --state NEW --dport 30000 -j ACCEPT # Now you should read up on iptables rules and consider whether ssh access # for everyone is really desired. Most likely you will only allow access from certain IPs. # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls (access via 'dmesg' command) -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy: -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT

  Read the article

< Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >