Search Results

Search found 3489 results on 140 pages for 'tcp'.

Page 61/140 | < Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >

• OpenVPN bridged not pinging beyond openvpn server on Ubuntu/Windows 2003

  - by ani

  I set up an OpenVPN server using Ubuntu and a windows server 2003 client to interconnect two networks between two different offices. They can now ping each other, but the rest of the network cannot be contacted by the windows client. Office 1 has internal network of: 192.168.0.0 255.255.240.0 Office 2 has internal network of: 192.168.16.0 255.255.255.0 And the configuration files are: Server.conf port 1194 --script-security 2 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" # TCP or UDP server? ;proto tcp proto udp dev tap0 ;dev tun ca ca.crt cert openvpn.crt key openvpn.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.0.59 255.255.240.0 192.168.6.72 192.168.6.75 push "route 192.168.0.0 255.255.240.0" push "dhcp-option DNS 192.168.0.2" push "dhcp-option DOMAIN testeers.local" keepalive 10 120 tls-auth ta.key 0 # This file is secret comp-lzo user nobody group nogroup persist-key persist-tun log /var/log/openvpn/openvpn.log status /var/log/openvpn-status.log verb 3 Client Config file client dev tap ;dev tun --script-security 2 ;proto tcp proto udp remote 1xx.2xx.xxx.124 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert admin-VAIO.crt key admin-VAIO.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 Ifconfig on the server now shows the following: br0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 inet addr:192.168.0.59 Bcast:192.168.15.255 Mask:255.255.240.0 inet6 addr: fe80::250:56ff:fe8b:1a49/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1081860 errors:0 dropped:1358 overruns:0 frame:0 TX packets:242385 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76600615 (76.6 MB) TX bytes:64474575 (64.4 MB) eth0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:1144125 errors:0 dropped:7172 overruns:0 frame:0 TX packets:252486 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:109893729 (109.8 MB) TX bytes:66372620 (66.3 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:67865 errors:0 dropped:0 overruns:0 frame:0 TX packets:67865 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5183276 (5.1 MB) TX bytes:5183276 (5.1 MB) tap0 Link encap:Ethernet HWaddr 32:4f:42:11:b7:c5 inet6 addr: fe80::304f:42ff:fe11:b7c5/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:3329 errors:0 dropped:0 overruns:0 frame:0 TX packets:215472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:373205 (373.2 KB) TX bytes:17465832 (17.4 MB)

  Read the article

• Port Forwarding on Actiontec GT704-WG Router Issues

  - by adamweeks

  I am trying to setup a server at customer's location that has the Actiontec GT704-WG DSL router. The port forwarding it not working at all. Here's the details: Server: OpenSuse Linux box with a static IP address of 192.168.1.200 Application running accepting connections on port 8060 Firewall disabled Local connections (within the network) working properly Router: Updated to latest firmware available DHCP range set to 192.168.1.69-192.168.1.199 to not have any conflicts with the server Firewall set to "off" Rule set in the "Applications" setting to forward 8060 TCP and UDP to 192.168.1.200 machine (I've tried using the "TCP,UDP" option as well as both individual options) I've also tried just simply putting the server in the DMZ to see if I could connect to anything, but still nothing. Looking for any clues before I call and waste hours explaining the issue to tech support.

  Read the article

• Trouble configuring sendmail to relay mail

  - by Warren Schubert

  I am trying to configure sendmail and ufw on an ubuntu server (ServerA) so that another server (ServerB) can send mail through it. In my /etc/mail/access file I have the following line (a.b.c.d is the IP of ServerB): Connect:a.b.c.d RELAY My ufw status shows the following rule I added: 25/tcp ALLOW a.b.c.d When I telnet from ServerA I get through: telnet localhost 25 When I telnet from ServerB I don't (w.x.y.z is the IP of ServerA): telnet w.x.y.z 25 telnet: Unable to connect to remote host: Connection refused I did restart the sendmail daemon after editing the access file. What could I be missing? Something in sendmail.mc? Edit: netstat -an|grep -w 25 tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN

  Read the article

• vsFTPd and iptables - how to configure them in CentOS 5.5?

  - by Vincenzo

  I've installed vsFTPd in CentOS 5.5, on TWO servers, and added this rule to their iptable-s: -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 21 -j ACCEPT Looks like this is not enough, since when I'm trying to upload a file from one server to another, I'm getting this result (IP address is masked): # ftp 99.99.99.99 Connected to …com (99.99.99.99). 220 (vsFTPd 2.0.5) Name (99.99.99.99:root): vinny 331 Please specify the password. Password: 230 Login successful. Remote system type is UNIX. Using binary mode to transfer files. ftp> ls 227 Entering Passive Mode (99,99,99,99,107,74) ftp: connect: No route to host I've found a few articles in the net about the second rule I have to add to iptables, but I didn't find the right syntax for it. Could you please help?

  Read the article

• iptables question

  - by RubyFreak

  i have a small network, with one valid IP and a firewall with 3 network interfaces (LAN, WAN, DMZ). I want to enable PAT on this valid IP to redirect http traffic to a server in my DMZ. (done) I want to enable MASQ on this ip from traffic that comes from my LAN (done) I want from my LAN as well to access my http server at DMZ. (partially) Question: in the above scenario, i cannot from my LAN, to access my http server in the DMZ, since it has the IP used by the MASQ (the only valid ip that i have). What would be the best option to solve this problem? network interfaces: eth0 (WAN) eth1 (DMZ) eth2 (LAN) /sbin/iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE /sbin/iptables -A FORWARD --o eth1 -d 2.2.2.2 -p tcp --dport 80 -j ACCEPT /sbin/iptables -t nat -A PREROUTING -i eth0 -d 1.1.1.1 -p tcp --dport 80 -j DNAT --to 2.2.2.2 /sbin/iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT /sbin/iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT /sbin/iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT

  Read the article

• Suspicious process running under user named

  - by Amit

  I get a lot of emails reporting this and I want this issue to auto correct itself. These process are run by my server and are a result of updates, session deletion and other legitimate session handling reported as false positives. Here's a sample report: Time: Sat Oct 20 00:00:03 2012 -0400 PID: 20077 Account: named Uptime: 326117 seconds Executable: /usr/sbin/nsd\00507d27e9\0053\00\00\00\00\00 (deleted) The file system shows this process is running an executable file that has been deleted. This typically happens when the original file has been replaced by a new file when the application is updated. To prevent this being reported again, restart the process that runs this excecutable file. See csf.conf and the PT_DELETED text for more information about the security implications of processes running deleted executable files. Command Line (often faked in exploits): /usr/sbin/nsd -c /etc/nsd/nsd.conf Network connections by the process (if any): udp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 udp: 127.0.0.1:53 -> 0.0.0.0:0 udp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 tcp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 tcp: 127.0.0.1:53 -> 0.0.0.0:0 tcp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 Files open by the process (if any): /dev/null /dev/null /dev/null Memory maps by the process (if any): 0045e000-00479000 r-xp 00000000 fd:00 2582025 /lib/ld-2.5.so 00479000-0047a000 r--p 0001a000 fd:00 2582025 /lib/ld-2.5.so 0047a000-0047b000 rw-p 0001b000 fd:00 2582025 /lib/ld-2.5.so 0047d000-005d5000 r-xp 00000000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d5000-005d7000 r--p 00157000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d7000-005d8000 rw-p 00159000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d8000-005db000 rw-p 005d8000 00:00 0 005dd000-005e0000 r-xp 00000000 fd:00 2582087 /lib/libdl-2.5.so 005e0000-005e1000 r--p 00002000 fd:00 2582087 /lib/libdl-2.5.so 005e1000-005e2000 rw-p 00003000 fd:00 2582087 /lib/libdl-2.5.so 0062b000-0063d000 r-xp 00000000 fd:00 2582079 /lib/libz.so.1.2.3 0063d000-0063e000 rw-p 00011000 fd:00 2582079 /lib/libz.so.1.2.3 00855000-0085f000 r-xp 00000000 fd:00 2582022 /lib/libnss_files-2.5.so 0085f000-00860000 r--p 00009000 fd:00 2582022 /lib/libnss_files-2.5.so 00860000-00861000 rw-p 0000a000 fd:00 2582022 /lib/libnss_files-2.5.so 00ac0000-00bea000 r-xp 00000000 fd:00 2582166 /lib/libcrypto.so.0.9.8e 00bea000-00bfe000 rw-p 00129000 fd:00 2582166 /lib/libcrypto.so.0.9.8e 00bfe000-00c01000 rw-p 00bfe000 00:00 0 00e68000-00e69000 r-xp 00e68000 00:00 0 [vdso] 08048000-08074000 r-xp 00000000 fd:00 927261 /usr/sbin/nsd 08074000-08079000 rw-p 0002b000 fd:00 927261 /usr/sbin/nsd 08079000-0808c000 rw-p 08079000 00:00 0 08a20000-08a67000 rw-p 08a20000 00:00 0 b7f8d000-b7ff2000 rw-p b7f8d000 00:00 0 b7ffd000-b7ffe000 rw-p b7ffd000 00:00 0 bfa6d000-bfa91000 rw-p bffda000 00:00 0 [stack] Would /etc/nsd/restart or kill -1 20077 solve the problem?

  Read the article

• httpd (no pid file) not running while restarting apache

  - by user59503

  Hi I am working on ubuntu. I got the error messages while try to restart apache. root@XXX:/etc/init.d# sudo /etc/init.d/apache2 restart * Restarting web server apache2 apache2: Could not reliably determine the server's fully qualified domain name, using xxx.xxx.xx.xxx for ServerName httpd (no pid file) not running apache2: Could not reliably determine the server's fully qualified domain name, using xxx.xxx.xx.xxx for ServerName (98)Address already in use: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs I got the following message when tried netstat -pant tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 0 32748 9950/httpd tcp 429 0 xxx.xxx.xx.xxx:80 xxx.xxx.xx.xxx:xxxxx CLOSE_WAIT 0 0

  Read the article

• Port Redirection on Mac OS X Lion

  - by Andreas

  I have tried to solve this issue using pf but with no luck. Basically, I am trying to redirect incoming port 443 traffic to port 22. I have tried to set up a rule in a file and load it in pf but I get syntax error. Can anyone with more experience with pf provide some insight? Here's what I've attempted: pass in on en1 proto tcp from any to any port 443 rdr-to 127.0.0.1 port 22 and pass in quick proto tcp to port 443 rdr-to 127.0.0.1 port 22 I've been able to do this in MacOSX Snow Leopard with ipfw: sudo ipfw add 1443 forward 127.0.0.1,22 ip from any to any 443 in but it doesn't work in Lion (it gives me an Invalid Argument error).

  Read the article

• iptables ACCEPT policy

  - by kamae

  In Redhat EL 6, iptables INPUT policy is ACCEPT but INPUT chain has REJECT entry in the end. /etc/syconfig/iptables is as below: *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT Do you know why the policy is ACCEPT not DROP? I think setting DROP policy is safer than ACCEPT in case to make mistake in the chain. Actually the policy is not applied to any packet: # iptables -L -v Chain INPUT (policy ACCEPT 0 packets, 0 bytes)

  Read the article

• Service haproxy error

  - by user128296

  I want to configure Haproxy for outgoing mail load balancing. my configuration file /etc/haproxy.cfg is. global maxconn 4096 # Total Max Connections. This is dependent on ulimit daemon nbproc 4 # Number of processing cores. Dual Dual-core Opteron is 4 cores for example. defaults mode tcp listen smtp_proxy 199.83.95.71:25 mode tcp option tcplog balance roundrobin # Load Balancing algorithm ## Define your servers to balance server r23.lbsmtp.org 74.117.x.x:25 weight 1 maxconn 512 check server r15.lbsmtp.org 199.71.x.x:25 weight 1 maxconn 512 check And when i start service haproxy i get this error. Starting HAproxy: [ALERT] 244/172148 (7354) : cannot bind socket for proxy smtp_proxy. Aborting. Please tell me where i am doing mistake.help will appreciated.

  Read the article

• Cannot open root device xvda1 or unknown-block(0,0)

  - by svoop

  I'm putting together a Dom0 and three DomU (all Gentoo) with kernel 3.5.7 and Xen 4.1.1. Each Dom has it's own md (md0 for Dom0, md1 for Dom1 etc). Dom0 works fine so far, however, I'm stuck trying to create DomUs. It appears the xvda1 device on DomU is not created or accessible: Parsing config file dom1 domainbuilder: detail: xc_dom_allocate: cmdline="root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3", features="(null)" domainbuilder: detail: xc_dom_kernel_mem: called domainbuilder: detail: xc_dom_boot_xen_init: ver 4.1, caps xen-3.0-x86_64 xen-3.0-x86_32p hvm-3.0-x86_32 hvm-3.0-x86_32p hvm-3.0-x86_64 domainbuilder: detail: xc_dom_parse_image: called domainbuilder: detail: xc_dom_find_loader: trying multiboot-binary loader ... domainbuilder: detail: loader probe failed domainbuilder: detail: xc_dom_find_loader: trying Linux bzImage loader ... domainbuilder: detail: xc_dom_malloc : 10530 kB domainbuilder: detail: xc_dom_do_gunzip: unzip ok, 0x2f7a4f -> 0xa48888 domainbuilder: detail: loader probe OK xc: detail: elf_parse_binary: phdr: paddr=0x1000000 memsz=0x558000 xc: detail: elf_parse_binary: phdr: paddr=0x1558000 memsz=0x690e8 xc: detail: elf_parse_binary: phdr: paddr=0x15c2000 memsz=0x127c0 xc: detail: elf_parse_binary: phdr: paddr=0x15d5000 memsz=0x533000 xc: detail: elf_parse_binary: memory: 0x1000000 -> 0x1b08000 xc: detail: elf_xen_parse_note: GUEST_OS = "linux" xc: detail: elf_xen_parse_note: GUEST_VERSION = "2.6" xc: detail: elf_xen_parse_note: XEN_VERSION = "xen-3.0" xc: detail: elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 xc: detail: elf_xen_parse_note: ENTRY = 0xffffffff815d5210 xc: detail: elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81001000 xc: detail: elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb" xc: detail: elf_xen_parse_note: PAE_MODE = "yes" xc: detail: elf_xen_parse_note: LOADER = "generic" xc: detail: elf_xen_parse_note: unknown xen elf note (0xd) xc: detail: elf_xen_parse_note: SUSPEND_CANCEL = 0x1 xc: detail: elf_xen_parse_note: HV_START_LOW = 0xffff800000000000 xc: detail: elf_xen_parse_note: PADDR_OFFSET = 0x0 xc: detail: elf_xen_addr_calc_check: addresses: xc: detail: virt_base = 0xffffffff80000000 xc: detail: elf_paddr_offset = 0x0 xc: detail: virt_offset = 0xffffffff80000000 xc: detail: virt_kstart = 0xffffffff81000000 xc: detail: virt_kend = 0xffffffff81b08000 xc: detail: virt_entry = 0xffffffff815d5210 xc: detail: p2m_base = 0xffffffffffffffff domainbuilder: detail: xc_dom_parse_elf_kernel: xen-3.0-x86_64: 0xffffffff81000000 -> 0xffffffff81b08000 domainbuilder: detail: xc_dom_mem_init: mem 5000 MB, pages 0x138800 pages, 4k each domainbuilder: detail: xc_dom_mem_init: 0x138800 pages domainbuilder: detail: xc_dom_boot_mem_init: called domainbuilder: detail: x86_compat: guest xen-3.0-x86_64, address size 64 domainbuilder: detail: xc_dom_malloc : 10000 kB domainbuilder: detail: xc_dom_build_image: called domainbuilder: detail: xc_dom_alloc_segment: kernel : 0xffffffff81000000 -> 0xffffffff81b08000 (pfn 0x1000 + 0xb08 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1000+0xb08 at 0x7fdec9b85000 xc: detail: elf_load_binary: phdr 0 at 0x0x7fdec9b85000 -> 0x0x7fdeca0dd000 xc: detail: elf_load_binary: phdr 1 at 0x0x7fdeca0dd000 -> 0x0x7fdeca1460e8 xc: detail: elf_load_binary: phdr 2 at 0x0x7fdeca147000 -> 0x0x7fdeca1597c0 xc: detail: elf_load_binary: phdr 3 at 0x0x7fdeca15a000 -> 0x0x7fdeca1cd000 domainbuilder: detail: xc_dom_alloc_segment: phys2mach : 0xffffffff81b08000 -> 0xffffffff824cc000 (pfn 0x1b08 + 0x9c4 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1b08+0x9c4 at 0x7fdec91c1000 domainbuilder: detail: xc_dom_alloc_page : start info : 0xffffffff824cc000 (pfn 0x24cc) domainbuilder: detail: xc_dom_alloc_page : xenstore : 0xffffffff824cd000 (pfn 0x24cd) domainbuilder: detail: xc_dom_alloc_page : console : 0xffffffff824ce000 (pfn 0x24ce) domainbuilder: detail: nr_page_tables: 0x0000ffffffffffff/48: 0xffff000000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x0000007fffffffff/39: 0xffffff8000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x000000003fffffff/30: 0xffffffff80000000 -> 0xffffffffbfffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x00000000001fffff/21: 0xffffffff80000000 -> 0xffffffff827fffff, 20 table(s) domainbuilder: detail: xc_dom_alloc_segment: page tables : 0xffffffff824cf000 -> 0xffffffff824e6000 (pfn 0x24cf + 0x17 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cf+0x17 at 0x7fdece676000 domainbuilder: detail: xc_dom_alloc_page : boot stack : 0xffffffff824e6000 (pfn 0x24e6) domainbuilder: detail: xc_dom_build_image : virt_alloc_end : 0xffffffff824e7000 domainbuilder: detail: xc_dom_build_image : virt_pgtab_end : 0xffffffff82800000 domainbuilder: detail: xc_dom_boot_image: called domainbuilder: detail: arch_setup_bootearly: doing nothing domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_64 <= matches domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32 domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_64 domainbuilder: detail: xc_dom_update_guest_p2m: dst 64bit, pages 0x138800 domainbuilder: detail: clear_page: pfn 0x24ce, mfn 0x37ddee domainbuilder: detail: clear_page: pfn 0x24cd, mfn 0x37ddef domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cc+0x1 at 0x7fdece675000 domainbuilder: detail: start_info_x86_64: called domainbuilder: detail: setup_hypercall_page: vaddr=0xffffffff81001000 pfn=0x1001 domainbuilder: detail: domain builder memory footprint domainbuilder: detail: allocated domainbuilder: detail: malloc : 20658 kB domainbuilder: detail: anon mmap : 0 bytes domainbuilder: detail: mapped domainbuilder: detail: file mmap : 0 bytes domainbuilder: detail: domU mmap : 21392 kB domainbuilder: detail: arch_setup_bootlate: shared_info: pfn 0x0, mfn 0xbaa6f domainbuilder: detail: shared_info_x86_64: called domainbuilder: detail: vcpu_x86_64: called domainbuilder: detail: vcpu_x86_64: cr3: pfn 0x24cf mfn 0x37dded domainbuilder: detail: launch_vm: called, ctxt=0x7fff224e4ea0 domainbuilder: detail: xc_dom_release: called Daemon running with PID 4639 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.5.7-gentoo (root@majordomo) (gcc version 4.5.4 (Gentoo 4.5.4 p1.0, pie-0.4.7) ) #1 SMP Tue Nov 20 10:49:51 CET 2012 [ 0.000000] Command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] ACPI in unprivileged domain disabled [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009ffff] usable [ 0.000000] Xen: [mem 0x00000000000a0000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000138ffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] MPS support code is not built-in. [ 0.000000] Using acpi=off or acpi=noirq or pci=noacpi may have problem [ 0.000000] DMI not present or invalid. [ 0.000000] No AGP bridge found [ 0.000000] e820: last_pfn = 0x139000 max_arch_pfn = 0x400000000 [ 0.000000] e820: last_pfn = 0x100000 max_arch_pfn = 0x400000000 [ 0.000000] init_memory_mapping: [mem 0x00000000-0xffffffff] [ 0.000000] init_memory_mapping: [mem 0x100000000-0x138ffffff] [ 0.000000] NUMA turned off [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000138ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x138ffffff] [ 0.000000] NODE_DATA [mem 0x1387fc000-0x1387fffff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00010000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x138ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00010000-0x0009ffff] [ 0.000000] node 0: [mem 0x00100000-0x138ffffff] [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] No local APIC present [ 0.000000] APIC: disable apic facility [ 0.000000] APIC: switched to apic NOOP [ 0.000000] e820: cannot find a gap in the 32bit address range [ 0.000000] e820: PCI devices with unassigned 32bit BARs may break! [ 0.000000] e820: [mem 0x139100000-0x1394fffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on Xen [ 0.000000] Xen version: 4.1.1 (preserve-AD) [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff880138400000 s75712 r8192 d22592 u2097152 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1259871 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Memory: 4943980k/5128192k available (3937k kernel code, 448k absent, 183764k reserved, 1951k data, 524k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:256 16 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [hvc0] enabled [ 0.000000] installing Xen timer for CPU 0 [ 0.000000] Detected 3411.602 MHz processor. [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 6823.20 BogoMIPS (lpj=3411602) [ 0.000999] pid_max: default: 32768 minimum: 301 [ 0.000999] Security Framework initialized [ 0.001355] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.002974] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003441] Mount-cache hash table entries: 256 [ 0.003595] Initializing cgroup subsys cpuacct [ 0.003599] Initializing cgroup subsys freezer [ 0.003637] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' [ 0.003637] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8) [ 0.003643] CPU: Physical Processor ID: 0 [ 0.003645] CPU: Processor Core ID: 0 [ 0.003702] SMP alternatives: switching to UP code [ 0.011791] Freeing SMP alternatives: 12k freed [ 0.011835] Performance Events: unsupported p6 CPU model 42 no PMU driver, software events only. [ 0.011886] Brought up 1 CPUs [ 0.011998] Grant tables using version 2 layout. [ 0.012009] Grant table initialized [ 0.012034] NET: Registered protocol family 16 [ 0.012328] PCI: setting up Xen PCI frontend stub [ 0.015089] bio: create slab <bio-0> at 0 [ 0.015158] ACPI: Interpreter disabled. [ 0.015180] xen/balloon: Initialising balloon driver. [ 0.015180] xen-balloon: Initialising balloon driver. [ 0.015180] vgaarb: loaded [ 0.016126] SCSI subsystem initialized [ 0.016314] PCI: System does not support PCI [ 0.016320] PCI: System does not support PCI [ 0.016435] NetLabel: Initializing [ 0.016438] NetLabel: domain hash size = 128 [ 0.016440] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.016447] NetLabel: unlabeled traffic allowed by default [ 0.016475] Switching to clocksource xen [ 0.017434] pnp: PnP ACPI: disabled [ 0.017501] NET: Registered protocol family 2 [ 0.017864] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.019322] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.020376] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.020497] TCP: Hash tables configured (established 524288 bind 65536) [ 0.020500] TCP: reno registered [ 0.020525] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020564] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020624] NET: Registered protocol family 1 [ 0.020658] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.020662] software IO TLB [mem 0xfb632000-0xff631fff] (64MB) mapped at [ffff8800fb632000-ffff8800ff631fff] [ 0.020750] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.021378] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.023378] msgmni has been set to 9656 [ 0.023544] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.023549] io scheduler noop registered [ 0.023551] io scheduler deadline registered [ 0.023580] io scheduler cfq registered (default) [ 0.023650] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.023845] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.024082] Non-volatile memory driver v1.3 [ 0.024085] Linux agpgart interface v0.103 [ 0.024207] Event-channel device installed. [ 0.024265] [drm] Initialized drm 1.1.0 20060810 [ 0.024268] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 0.025145] brd: module loaded [ 0.025565] loop: module loaded [ 0.045646] Initialising Xen virtual ethernet driver. [ 0.198264] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.199096] i8042: No controller found [ 0.199139] mousedev: PS/2 mouse device common for all mice [ 0.259303] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 0.259353] rtc_cmos: probe of rtc_cmos failed with error -38 [ 0.259440] md: raid1 personality registered for level 1 [ 0.259542] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 0.259732] ip_tables: (C) 2000-2006 Netfilter Core Team [ 0.259747] TCP: cubic registered [ 0.259886] NET: Registered protocol family 10 [ 0.260031] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 0.260070] sit: IPv6 over IPv4 tunneling driver [ 0.260194] NET: Registered protocol family 17 [ 0.260213] Bridge firewalling registered [ 5.360075] XENBUS: Waiting for devices to initialise: 25s...20s...15s...10s...5s...0s...235s...230s...225s...220s...215s...210s...205s...200s...195s...190s...185s...180s...175s...170s...165s...160s...155s...150s...145s...140s...135s...130s...125s...120s...115s...110s...105s...100s...95s...90s...85s...80s...75s...70s...65s...60s...55s...50s...45s...40s...35s...30s...25s...20s...15s...10s...5s...0s... [ 270.360180] XENBUS: Timeout connecting to device: device/vbd/51713 (local state 3, remote state 1) [ 270.360273] md: Waiting for all devices to be available before autodetect [ 270.360277] md: If you don't use raid, use raid=noautodetect [ 270.360388] md: Autodetecting RAID arrays. [ 270.360392] md: Scanned 0 and added 0 devices. [ 270.360394] md: autorun ... [ 270.360395] md: ... autorun DONE. [ 270.360431] VFS: Cannot open root device "xvda1" or unknown-block(0,0): error -6 [ 270.360435] Please append a correct "root=" boot option; here are the available partitions: [ 270.360440] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 270.360444] Pid: 1, comm: swapper/0 Not tainted 3.5.7-gentoo #1 [ 270.360446] Call Trace: [ 270.360454] [<ffffffff813d2205>] ? panic+0xbe/0x1c5 [ 270.360459] [<ffffffff813d2358>] ? printk+0x4c/0x51 [ 270.360464] [<ffffffff815d5fb7>] ? mount_block_root+0x24f/0x26d [ 270.360469] [<ffffffff815d62b6>] ? prepare_namespace+0x168/0x192 [ 270.360474] [<ffffffff815d5ca7>] ? kernel_init+0x1b0/0x1c2 [ 270.360477] [<ffffffff815d5500>] ? loglevel+0x34/0x34 [ 270.360482] [<ffffffff813d5a64>] ? kernel_thread_helper+0x4/0x10 [ 270.360486] [<ffffffff813d4038>] ? retint_restore_args+0x5/0x6 [ 270.360490] [<ffffffff813d5a60>] ? gs_change+0x13/0x13 The config: name = "dom1" bootloader = "/usr/bin/pygrub" root = "/dev/xvda1 ro" extra = "3" # runlevel memory = 5000 disk = [ 'phy:/dev/md1,xvda1,w' ] # vif = [ 'ip=..., vifname=veth1' ] # none for now Here are some details on the Dom0 kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y # CONFIG_XEN_BLKDEV_FRONTEND is not set CONFIG_XEN_BLKDEV_BACKEND=y # CONFIG_XEN_NETDEV_FRONTEND is not set CONFIG_XEN_NETDEV_BACKEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y CONFIG_XEN_BACKEND=y CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PCIDEV_BACKEND=m CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m And the DomU kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y CONFIG_XEN_BLKDEV_FRONTEND=y CONFIG_XEN_NETDEV_FRONTEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y # CONFIG_XEN_BACKEND is not set CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m Any ideas what I'm doing wrong here? Thanks a lot!

  Read the article

• routing through multiple subinterfaces in debian

  - by Kstro21

  my question is as simple as the title, i have a debian 6 , 2 NICs, 3 different subnets in a single interface, just like this: auto eth0 iface eth0 inet static address 192.168.106.254 netmask 255.255.255.0 auto eth0:0 iface eth0:0 inet static address 172.19.221.81 netmask 255.255.255.248 auto eth0:1 iface eth0:1 inet static address 192.168.254.1 netmask 255.255.255.248 auto eth1 iface eth1 inet static address 172.19.216.3 netmask 255.255.255.0 gateway 172.19.216.13 eth0 is conected to a swith with 3 differents vlans, eth1 is conected to a router. No iptables DROP, so, all traffic is allowed. Now, passing the traffic through eth0 is OK, passing the traffic through eth0:0 is OK, but, passing the traffic through eth0:1 is not working, i can ping the ip address of that sub interface from a pc where this ip is the default gateway, but can't get to servers in the subnet of the eth1 interface, the traffic is not passing, even when i set the iptables to log all the traffic in the FORWARD chain and i can see the traffic there, but, the traffic is not really passing. And the funny is i can do any the other way around, i mean, passing from eth1 to eth0:1, RDP, telnet, ping, etc, doing some work with the iptable, i manage to pass some traffic from eth0:1 to eth1, the iptables look like this: iptables -t nat PREROUTING -d 192.168.254.1/32 -p tcp -m multiport --dports 25,110,5269 -j DNAT --to-destination 172.19.216.1 iptables -t nat PREROUTING -d 192.168.254.1/32 -p udp -m udp --dport 53 -j DNAT --to-destination 172.19.216.9 iptables -t nat PREROUTING -d 192.168.254.1/32 -p tcp -m tcp --dport 21 -j DNAT --to-destination 172.19.216.11 iptables -t nat POSTROUTING -s 172.19.216.0/24 -d 172.19.221.80/29 -j SNAT --to-source 172.19.221.81 iptables -t nat POSTROUTING -s 172.19.216.0/24 -d 192.168.254.0/29 -j SNAT --to-source 192.168.254.1 iptables -t nat POSTROUTING -s 172.19.216.0/24 -o eth0 -j SNAT --to-source 192.168.106.254 dong this is working, but,it is really a headache have to map each port with the server, imagine if i move the service from server, so, now i have doubts: can debian route through multiple subinterfaces?? exist a limit for this?? if not, what i'm doing wrong when i have the same setup with other subnets and it is working ok?? without the iptables rules in the nat, it doesn't work thanks and i hope good comments/answers

  Read the article

• Apache: How can I make my localhost on 192.168.1.101 visible from 192.168.1.102?

  - by takpar

  Hi, I've setup a Apache web server on Ubuntu Linux. I can see http://localhost well. But I can't see localhost from other machines in my network using IP address: http://192.168.1.101 I added the lines below to my apache conf: `Allow from 192.168.1` but it did not work. It says "the connection has timed out". what should i do? PS: adp@adp-desktop:~$ sudo netstat -ap | grep apache tcp 0 0 *:www *:* LISTEN 10581/apache2 tcp 0 0 localhost:www localhost:46017 ESTABLISHED 10586/apache2

  Read the article

• Iptables Allow MYSQL server incoming requests

  - by thompatry

  I am trying to get my new MediaWiki server to allow connections to our MySql Server and right now I cannot get my iptables firewall set up right for this. The rule I am applying is the following iptables -A INPUT -p tcp -d 129.130.155.39 --dport 3306 -j ACCEPT # MySQL But my iptables log is still show that the connections can not be established and is being blocked/denied. Nov 21 09:48:39 hds-it kernel: Firewall Deny: [OUTPUT] IN= OUT=eth1 SRC=129.130.155.210 DST=129.130.155.39 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=29232 DF PROTO=TCP SPT=58862 DPT=3306 SEQ=914529531 ACK=0 WINDOW=14600 RES=0x00 SYN URGP=0 OPT (020405B40402080A03BCF2BC0000000001030307) When I turn off iptables, everything works as it should including editing the wiki database. What am I doing wrong with my rule.

  Read the article

• Increase the compression performance of VPN

  - by Martin

  I am currently switching from a system with HPN-SSH tunnels and enabled compression to something VPN based. I have tried tinc and n2n so far, hamachi requires a library I do not have. In my primitive benchmarks I am not satisfied with the achievable bandwidth compared to the SSH tunnels. In tinc the low LZO setting performed best, but compression is only available in UDP mode. Ideally I would like to have a TCP-based VPN with a multi-threaded compression. Can you suggest me some ideas how to increase the performance? Would it be possible to somehow put a compression filter in front of the tun interface? Or are there any VPN implementations that might be better suited for my needs (fast compression, TCP-based, switch mode, does not have to be super-secure)? I would consider tunnelling Ethernet over SSH, but according to some articles it is not advisable.

  Read the article

• vmware workstation - virtual network adapters missing from ipconfig, still show in networking (XP host)

  - by Adam

  Hi Folks - here's a new one for me, and my first time posting here: I installed VMWare workstation 7.1 on a new PC. VMWare properly installs the virtual network adapters under the Network Connections control panel, however for some reason they do not show up under ipconfig, which is very weird. They also don't appear anywhere in "route print". I don't have network connectivity to the VM. My guesses are perhaps some conflict with Symantec AntiVirus or Symantec Client Firewall. Tried the following things: enabling TCP/IP in the virtual network adapters (they often get installed with it disabled for some reason) Restoring defualts in the VMnetcfg gui tool (this causes an uninstall and reinstall of the virtual network adapters on the host) Re-installing vmware workstation Uninstalling checkpoint secureremote and then reinstalling vmware Just to be clear, this problem is totally on the host. In my searching for stuff about (non-vmware) adapters missing from ipconfig, I see some posts about resetting the TCP/IP stack using netsh. Looking into that next... Thanks!

  Read the article

• wifi connection turns off oll the time

  - by er-v

  Hello! I realy need help with one strange problem. I have a wifi network in my appartment with wireless N home router Trendnet tew-652BRP. Everething work fine for three of my laptops, but I have one PC with D-Link DWA-140 adapter. It looses connection 2-3 times in 5 minutes. There is following messages in my system log when it does so: The browser has forced an election on network \Device\NetBT_Tcpip_{9537A5C1-3B43-4C56-B94C-CE69A257C3AD} because a master browser was stopped. The TCP/IP NetBIOS Helper service was successfully sent a stop control. The reason specified was: 0x40030011 [Operating System: Network Connectivity (Planned)] Comment: None The TCP/IP NetBIOS Helper service entered the stopped state. in order of appearence. How can I stop it? I have the latest driver installed.

  Read the article

• unable to connect to remote sql server from SHDSL router

  - by user529265

  Got a new leased line network to our office that came with a SHDSL router (Watson). Currently, we are unable to use Sql Server management studio to connect to remote Sql databases. It errors out saying A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: TCP Provider, error: 0 - The specified network name is no longer available.) (Microsoft SQL Server, Error: 64) I logged into the Watson management panel and unblocked all the ports for TCP traffic (specified the range as 0 to 60000 and UDP as well - this include 1443 required for connecting to SQL Server). The router is the only thing that has changed. We are able to connect to it from other networks just fine. Is there something we are missing here. Any help would be greatly appreciated.

  Read the article

• Iptables remote port forwarding and dynamic remote ip

  - by lbwtz2

  Hello, I want to forward a port from my remote vps to my domestic server and I am quite a newbie with iptables. The problem is that I am using a dynamic dns service to reach my home server from the internet so I don't have a fixed ip and iptables doesn't like urls. The rules I am willing to use are these: -t nat -A PREROUTING -p tcp -i eth0 -d xxx.xxx.xxx.xxx --dport 8888 -j DNAT --to myhome.tld:80 -A FORWARD -p tcp -i eth0 -d myhome.tld --dport 80 -j ACCEPT Of course I recevie a Error BAD IP ADDRESS because of myhome.tld. What can I do?

  Read the article

• iptables - drop all HTTP(S) traffic but from CloudFlare

  - by Martin

  I would like to allow only HTTP(S) traffic coming from CloudFlare. In that way attackers cannot attack the server directly. I know CloudFlare is not mainly a DDoS mitigator, but I would like to try it either way. I'm currently only having access to iptables (ipv4 only), but will try to install ip6tables soon. I just need to have this fixed soon. (we're getting (D)DoSed atm.) I was thinking about something like this: iptables -I INPUT -s <CloudFlare IP> --dport 80 -j ACCEPT iptables -I INPUT -s <CloudFlare IP> --dport 443 -j ACCEPT iptables -I INPUT -p tcp --dport 80 -j DROP iptables -I INPUT -p tcp --dport 443 -j DROP I know that CloudFlare has multiple IPs, but just for an example. Would this be the right way?

  Read the article

• afp/smb transfers caps at 2 megabytes/sec, wireless N

  - by RD.

  I wanted to transfer files between two mac computers. The network is wireless-N and both computers have wireless-N modules in them. The problem is that when I transfer files between them, via file sharing (afp) the network speed caps at 2 megabytes/sec. Just downloading files from the internet I can get faster speeds, so this isn't a constriction of my wifi bandwidth, it appears to be a constriction of the protocol being used. My wifi-n is set to 130mbits, so I should see real world transfer speeds around 12-16 megabytes/sec I did this command on both computers sudo sysctl -w net.inet.tcp.delayed_ack=0 which is supposed to lower tcp overhead, but this did not affect it. How can I get the speed I am expecting?

  Read the article

• %sessionname% returns incorrect session name

  - by Samuel Walker

  I have a virtualised Windows XP SP3 machine, which I am connecting to over Remote Desktop. One of my scripts needs to use the %sessionname% variable. However this returns incorrect information. C:\>%sessionname% constantly returns RDP-Tcp#5, instead of the value for the currently connected session (RDP-Tcp#35 or similar), as shown in Task Manager This causes my scripts to contain incorrect information. What can I do to resolve this? Edit Further Information: A restart appears to solve the problem for the first connection, but then subsequent connections have the numbers fall out of sync again.

  Read the article

• cannot access my own computer through My Network Places

  - by WebMAOhist

  My home Windows XP Pro SP3 machine is DHCP client receiving configurations from ISP. Trying to access in WindowsExplorer -My Network Places - Microsoft Windows Network shows Workgroup with a delay of 3 min and then popups messagebox: Microsoft Windows Network Workgroup is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.The list of servers for this workgroup is not currently available OK I am logged-in as local machine Administrator. The internet is accessible (I am writing this post through it) The Firewall is disabled The "Computer Bowser" and all networking services, I could find, are running Control Panel -- Network Connections -- Properties (of connection) --- Internet Protocol (TCP/IP), btn Properties --- --- tab General, btn "Advanced..." -- tab WINS-- rbtn "Enable NetBIOS over TCP/IP" checked Why cannot I access my own PC (and shares on it) through My Network Places What is the possible problem? How to daignose the problem?

  Read the article

• OpenVPN IPv6 over IPv4 tunnel

  - by user66779

  Today I installed OpenVPN 2.3rc2 on both my windows 7 client machine and centos 6 server. This new version of OpenVPN provides full compatibility for IPv6. The Problem: I am currently able to connect to the server (through the IPv4 tunnel) and ping the IPv6 address which is assigned to my client and I can also ping the tun0 interface on the server. However, I cannot browse to any IPv6 websites. My vps provider has given me this: 2607:f840:0044:0022:0000:0000:0000:0000/64 is routed to this server (2607:f840:0:3f:0:0:0:eda). This is ifconfig after setup with OpenVPN running: eth0 Link encap:Ethernet HWaddr 00:16:3E:12:77:54 inet addr:208.111.39.160 Bcast:208.111.39.255 Mask:255.255.255.0 inet6 addr: 2607:f740:0:3f::eda/64 Scope:Global inet6 addr: fe80::216:3eff:fe12:7754/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2317253 errors:0 dropped:7263 overruns:0 frame:0 TX packets:1977414 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1696120096 (1.5 GiB) TX bytes:1735352992 (1.6 GiB) Interrupt:29 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 inet6 addr: 2607:f740:44:22::1/64 Scope:Global UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:739567 errors:0 dropped:0 overruns:0 frame:0 TX packets:1218240 errors:0 dropped:1542 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:46512557 (44.3 MiB) TX bytes:1559930874 (1.4 GiB) So OpenVPN is sucessfully creating a tun0 interface and assigning clients IPv6 addresses using 2607:f840:44:22::/64. The first client to connect is getting 2607:f840:44:22::1000 and the second 2607:f840:44:22::1001, and so on... plus 1 each time. After connecting as the first client, I can ping from my windows client machine 2607:f740:44:22::1 and 2607:f740:44:22::1000. However, I have no access to IPv6 websites. I believe the problem is that the tun0 IPv6 addressees are not being forwarded to the eth0 interface. This is the firewall running on the server: #!/bin/sh # # iptables configuration script # # Flush all current rules from iptables # iptables -F iptables -t nat -F # # Allow SSH connections on tcp port 22 # iptables -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22 -j ACCEPT # # Set access for localhost # iptables -A INPUT -i lo -j ACCEPT # # Accept connections on 1195 for vpn access from client # iptables -A INPUT -i eth0 -p udp --dport 1195 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p udp --sport 1195 -m state --state ESTABLISHED -j ACCEPT # # Apply forwarding for OpenVPN Tunneling # iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to 209.111.39.160 iptables -A FORWARD -j REJECT # # Enable forwarding # echo 1 > /proc/sys/net/ipv4/ip_forward # # Set default policies for INPUT, FORWARD and OUTPUT chains # iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT # # IPv6 # IP6TABLES=/sbin/ip6tables $IP6TABLES -F INPUT $IP6TABLES -F FORWARD $IP6TABLES -F OUTPUT echo -n "1" >/proc/sys/net/ipv6/conf/all/forwarding echo -n "1" >/proc/sys/net/ipv6/conf/all/proxy_ndp echo -n "0" >/proc/sys/net/ipv6/conf/all/autoconf echo -n "0" >/proc/sys/net/ipv6/conf/all/accept_ra $IP6TABLES -A INPUT -i eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT $IP6TABLES -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT $IP6TABLES -A INPUT -i eth0 -p icmpv6 -j ACCEPT $IP6TABLES -P INPUT ACCEPT $IP6TABLES -P FORWARD ACCEPT $IP6TABLES -P OUTPUT ACCEPT Server.conf: server-ipv6 2607:f840:44:22::/64 server 10.8.0.0 255.255.255.0 port 1195 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh2048.pem ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" keepalive 10 60 tls-auth ta.key 0 cipher AES-256-CBC comp-lzo user nobody group nobody persist-key persist-tun status openvpn-status.log log-append openvpn.log verb 5 Client.conf: client dev tun nobind keepalive 10 60 hand-window 15 remote 209.111.39.160 1195 udp persist-key persist-tun ca ca.crt key client1.key cert client1.crt remote-cert-tls server tls-auth ta.key 1 comp-lzo verb 3 cipher AES-256-CBC I'm not sure where I am going wrong, it could be the firewall, or something missing from server or client.conf. This version of OpenVPN was only released yesterday, and there's little info on the internet about how to setup an IPv6 over IPv4 vpn tunnel. I've read the manual for this new version of OpenVPN (parts pertaining to IPv6) and it provides very little info too. Thanks for any help.

  Read the article

• virtualbox port forwarding - firewall config

  - by Roose

  i have a ubuntu host system with virtualbox running a windows server. In Virtualbox i have configured the network with a NAT interface and port forwarding for the RDP deamon running inside the vm. That works really well - i can connect to the windows rdp service over the internet. TCP *:3389 - *:3389 Now i like to restrict the access to the rdp service to only 3 public ip addresses and have no idea how to do that via iptables / shorewall. Something like: ACCEPT net:91.x.x.x fw tcp 3389 (shorewall rule) isn't working. Would be glad for any hint.

  Read the article

< Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >