Search Results

Search found 15099 results on 604 pages for 'stop loading'.

Page 542/604 | < Previous Page | 538 539 540 541 542 543 544 545 546 547 548 549  | Next Page >

• Wireless Network Performance Issues

  - by colithium

  My brand new Dell XPS system has been running flawlessly except its abysmal download speeds. I have tried isolating every variable I could possibly think of but I can't figure out the problem. I've talked to Dell and Belkin without making progress (thought I'd try). Here are the speeds: Note that most of the time, upload speeds are actually much faster than download speeds (around 4.0 Mb/s which is better than most other devices on the network) It's not the ISP. The slowdown happens even when transferring files inside the network. Plus every other wireless device gets approximately this: It's not the wireless router. It's a Lynksis WRT160N v1 with the latest firmware (1.02.2). Plus everything else connected to it has normal speeds. It's not the browser. Speeds are the same in IE, FF, and when transferring files with Windows between computers. It's not the wireless adapter. I've tried a Belkin N Wireless USB Adapter (which works fine on another computer) and a Dell Wireless Draft 802.11n WLAN Mini-Card. They have the same slow speeds when connected to the problem computer. It's not the adapter connection. One adapter used USB and the other is a Mini-Card. It's not antenna placement. With the same antenna position and the same device, I get different speeds when connected to the problem computer vs a good computer. Plus everything reports the connection speed as at least 11Mbps and good signal strength. I've tried disabling IPv6 since it sometimes causes weird problems. I've tried disabling Windows Firewall/anti-virus. I've ensured the computer has updated drivers for both adapters. I've ensured that Windows is up to date and so is the BIOS. For the USB adapter I ensured that that USB port functioned at normal speeds with other USB devices. What else could it possibly be? I finally received my copy of Windows 7 and will be trying that. I'd rather not install Windows 7 because of a particular program that will stop working so a solution besides that is welcome. Specs: Vista x64 Core i7 920 6GB RAM 500GB HD GTX 260

  Read the article

• Jetty interprets JETTY_ARGS as file name

  - by Lena Schimmel

  I'm running Jetty (version "null 6.1.22") on Ubuntu 10.04. It's running fine until I need JSP support. According to several blog posts I need to set the JETTY_ARGS to OPTIONS=Server,jsp. However, if I put this into /etc/default/jetty: JETTY_ARGS=OPTIONS=Server,jsp and restart Jetty via /etc/init.d/jetty stop && /etc/init.d/jetty start, it reports success, but does not accept connections. I notices that it logs something to /usr/share/jetty/logs/out.log: 2012-09-11 11:19:05.110:WARN::EXCEPTION java.io.FileNotFoundException: /var/cache/jetty/tmp/OPTIONS=Server,jsp (No such file or directory) at java.io.FileInputStream.open(Native Method) at java.io.FileInputStream.<init>(FileInputStream.java:137) at java.io.FileInputStream.<init>(FileInputStream.java:96) at sun.net.www.protocol.file.FileURLConnection.connect(FileURLConnection.java:87) at sun.net.www.protocol.file.FileURLConnection.getInputStream(FileURLConnection.java:178) at com.sun.org.apache.xerces.internal.impl.XMLEntityManager.setupCurrentEntity(XMLEntityManager.java:630) at com.sun.org.apache.xerces.internal.impl.XMLVersionDetector.determineDocVersion(XMLVersionDetector.java:189) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:776) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:741) at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(XMLParser.java:123) at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1208) at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:525) at javax.xml.parsers.SAXParser.parse(SAXParser.java:392) at org.mortbay.xml.XmlParser.parse(XmlParser.java:188) at org.mortbay.xml.XmlParser.parse(XmlParser.java:204) at org.mortbay.xml.XmlConfiguration.<init>(XmlConfiguration.java:109) at org.mortbay.xml.XmlConfiguration.main(XmlConfiguration.java:969) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:616) at org.mortbay.start.Main.invokeMain(Main.java:194) at org.mortbay.start.Main.start(Main.java:534) at org.mortbay.jetty.start.daemon.Bootstrap.start(Bootstrap.java:30) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:616) at org.apache.commons.daemon.support.DaemonLoader.start(DaemonLoader.java:177) That is, whatever I put into JETTY_ARGS, it inteprets is as a filename inside /var/cache/jetty/tmp/ and tries to parse that file as XML (or does it parse some other XML and tries to read that file as a DTD? I'm not sure.). This doesn't seem to make any sense to me, especially since that directory is entirely empty. I've verified this with several other Strings, not only OPTIONS=Server,jsp.

  Read the article

• How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files

  - by yegor

  Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

  Read the article

• How to keep group-writeable shares on Samba with OSX clients?

  - by Oliver Salzburg

  I have a FreeNAS server on a network with OSX and Windows clients. When the OSX clients interact with SMB/CIFS shares on the server, they are causing permission problems for all other clients. Update: I can no longer verify any answers because we abandoned the project, but feel free to post any help for future visitors. The details of this behavior seem to also be dependent on the version of OSX the client is running. For this question, let's assume a client running 10.8.2. When I mount the CIFS share on an OSX client and create a new directory on it, the directory will be created with drwxr-x-rx permissions. This is undesirable because it will not allow anyone but me to write to the directory. There are other users in my group which should have write permissions as well. This behavior happens even though the following settings are present in smb.conf on the server: [global] create mask= 0666 directory mask= 0777 [share] force directory mode= 0775 force create mode= 0660 I was under the impression that these settings should make sure that directories are at least created with rwxrwxr-x permissions. But, I guess, that doesn't stop the client from changing the permissions after creating the directory. When I create a folder on the same share from a Windows client, the new folder will have the desired access permissions (rwxrwxrwx), so I'm currently assuming that the problem lies with the OSX client. I guess this wouldn't be such an issue if you could easily change the permissions of the directories you've created, but you can't. When opening the directory info in Finder, I get the old "You have custom access" notice with no ability to make any changes. I'm assuming that this is caused because we're using Windows ACLs on the share, but that's just a wild guess. Changing the write permissions for the group through the terminal works fine, but this is unpractical for the deployment and unreasonable to expect from anyone to do. This is the complete smb.conf: [global] encrypt passwords = yes dns proxy = no strict locking = no read raw = yes write raw = yes oplocks = yes max xmit = 65535 deadtime = 15 display charset = LOCALE max log size = 10 syslog only = yes syslog = 1 load printers = no printing = bsd printcap name = /dev/null disable spoolss = yes smb passwd file = /var/etc/private/smbpasswd private dir = /var/etc/private getwd cache = yes guest account = nobody map to guest = Bad Password obey pam restrictions = Yes # NOTE: read smb.conf. directory name cache size = 0 max protocol = SMB2 netbios name = freenas workgroup = COMPANY server string = FreeNAS Server store dos attributes = yes hostname lookups = yes security = user passdb backend = ldapsam:ldap://ldap.company.local ldap admin dn = cn=admin,dc=company,dc=local ldap suffix = dc=company,dc=local ldap user suffix = ou=Users ldap group suffix = ou=Groups ldap machine suffix = ou=Computers ldap ssl = off ldap replication sleep = 1000 ldap passwd sync = yes #ldap debug level = 1 #ldap debug threshold = 1 ldapsam:trusted = yes idmap uid = 10000-39999 idmap gid = 10000-39999 create mask = 0666 directory mask = 0777 client ntlmv2 auth = yes dos charset = CP437 unix charset = UTF-8 log level = 1 [share] path = /mnt/zfs0 printable = no veto files = /.snap/.windows/.zfs/ writeable = yes browseable = yes inherit owner = no inherit permissions = no vfs objects = zfsacl guest ok = no inherit acls = Yes map archive = No map readonly = no nfs4:mode = special nfs4:acedup = merge nfs4:chown = yes hide dot files force directory mode = 0775 force create mode = 0660

  Read the article

• SQL Server 2008 - Error starting service - model.mdf not found?!

  - by alex

  my SQL server 2008 was running fine. About an hour ago, it suddenly stopped - the MSSQLSERVER service had stopped I right clicked, clicked start, and it said the service had started, and stopped I looked in the event log and saw these two errors: 17207 : udopen: Operating system error 3(error not found) during the creation/opening of physical device C:\Program Files\Microsoft SQL Server\MSSQL\data\model.mdf. 17204 : FCB::Open failed: Could not open device C:\Program Files\Microsoft SQL Server\MSSQL\data\model.mdf for virtual device number (VDN) 1. The model.mdf db has NEVER been in that location - i specified drive F: to use for data / log during install. I checked the SQL Configuration Manager, to try and set startup params, but SQL Server is not listed as one of the services..... EDIT: I've now moved the db to where it was looking for: C:\Program Files\Microsoft SQL Server\MSSQL\data\ directory. Now if I start the service, it still does not work - i get this error message in the log: Could not find row in sysindexes for database ID 3, object ID 1, index ID 1. Run DBCC CHECKTABLE on sysindexes. Interestingly, i checked the error log - around the time users reported problems, there is this: 2010-01-08 17:11:26.44 spid51 Configuration option 'show advanced options' changed from 0 to 1. Run the RECONFIGURE statement to install. 2010-01-08 17:11:26.44 spid51 FILESTREAM: effective level = 0, configured level = 0, file system access share name = 'MSSQLSERVER'. 2010-01-08 17:11:26.44 spid51 Configuration option 'Agent XPs' changed from 1 to 0. Run the RECONFIGURE statement to install. 2010-01-08 17:11:26.44 spid51 FILESTREAM: effective level = 0, configured level = 0, file system access share name = 'MSSQLSERVER'. 2010-01-08 17:11:26.44 spid51 Configuration option 'show advanced options' changed from 1 to 0. Run the RECONFIGURE statement to install. 2010-01-08 17:11:26.44 spid51 FILESTREAM: effective level = 0, configured level = 0, file system access share name = 'MSSQLSERVER'. 2010-01-08 17:11:44.89 spid10s Service Broker manager has shut down. 2010-01-08 17:11:47.83 spid7s SQL Server is terminating in response to a 'stop' request from Service Control Manager. This is an informational message only. No user action is required. 2010-01-08 17:11:47.83 spid7s SQL Trace was stopped due to server shutdown. Trace ID = '1'. This is an informational message only; no user action is required.

  Read the article

• iptables : how to correctly allow incoming and outgoing traffic for certain ports?

  - by Rubytastic

  Im trying to get incoming and outgoing traffic to be enabled on specific ports, because I block everything at the end of the iptables rules. INPUT and FORWARD reject. What would be the appropiate way to open certain ports for all traffic incoming and outgoing? From docs I found below but one has to really define both lines? iptables -A INPUT -i eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT I try to open ports for xmpp service and some other deamons running on server. Rules: *filter # Allow all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -d 127.0.0.0/8 -j REJECT # Accept all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow all outbound traffic - you can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allow HTTP # Prevent DDOS attacks (http://blog.bodhizazen.net/linux/prevent-dos-with-iptables/) # Disallow HTTPS -A INPUT -p tcp --dport 80 -m state --state NEW -m limit --limit 50/minute --limit-burst 200 -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -m limit --limit 50/second --limit-burst 50 -j ACCEPT -A INPUT -p tcp --dport 443 -j DROP # Allow SSH connections # The -dport number should be the same port number you set in sshd_config -A INPUT -p tcp -s <myip> --dport ssh -j ACCEPT -A INPUT -p tcp -s <myip> --dport 5984 -j ACCEPT -A INPUT -p tcp --dport ssh -j REJECT # Attempt to block portscans # Anyone who tried to portscan us is locked out for an entire day. -A INPUT -m recent --name portscan --rcheck --seconds 86400 -j DROP -A FORWARD -m recent --name portscan --rcheck --seconds 86400 -j DROP # Once the day has passed, remove them from the portscan list -A INPUT -m recent --name portscan --remove -A FORWARD -m recent --name portscan --remove # These rules add scanners to the portscan list, and log the attempt. -A INPUT -p tcp -m tcp --dport 139 -m recent --name portscan --set -j LOG --log-prefix "Portscan:" -A INPUT -p tcp -m tcp --dport 139 -m recent --name portscan --set -j DROP -A FORWARD -p tcp -m tcp --dport 139 -m recent --name portscan --set -j LOG --log-prefix "Portscan:" -A FORWARD -p tcp -m tcp --dport 139 -m recent --name portscan --set -j DROP # Stop smurf attacks -A INPUT -p icmp -m icmp --icmp-type address-mask-request -j DROP -A INPUT -p icmp -m icmp --icmp-type timestamp-request -j DROP -A INPUT -p icmp -m icmp -j DROP # Drop excessive RST packets to avoid smurf attacks -A INPUT -p tcp -m tcp --tcp-flags RST RST -m limit --limit 2/second --limit-burst 2 -j ACCEPT # Don't allow pings through -A INPUT -p icmp -m icmp --icmp-type 8 -j DROP # Log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT

  Read the article

• Plesk Postfix Mail Server 9.5.4 very heavy load, 1000s of processes

  - by Eugene van der Merwe

  Our Plesk Linux Ubuntu 64-bit mail server has extremely high load and we don't know how to isolate it. The load was okay will two weeks ago but in the last two weeks it's seriously deteriorated. The mail server has been running for years and we have had sporadic performance issues. Normally we reduce the load by turning off all SPAM checks until the problem is sorted (which sometimes resolves itself). Currently we have turned of real time block lists, SPF checking and we have attempted to turn off SpamAssassin. No matter what we do the SpamAssassin check box stays ticked in the GUI. Out of desperation we have done /etc/init.d/psa-spamassassin stop. For years we haven't been able to do SpamAssassin because it kills the server. We would like to use it but performance is more important for now. We cannot turn off Greylisting. The moment we turn off Greylisting our help desk is inandated with calls. Out of desperation we investigated truncating the Greylisting database which is now 2.5 GB big but we abandoned this after noticing turning of Greylisting doesn't improve the performance at all. We have no anti-virus. It's just more load and Dr. Web never really worked that well for us. But we'll try that if it will make a difference. We have implemented Postfix Anvil. This seems to have made the situation worse so we disabled it. We’re not sure if this is the case. Our current mail server is configured to forward all SMTP to a relay server. We did so to reduce the load. This helped a lot because outgoing queues are generally empty. We are running in an Expand configuration. The mail server has about 12 000 accounts of which maybe half are active. We have read through this document: http://www.postfix.org/STRESS_README.html but there are too many settings and we don’t know which ones to choose. Please assist urgently. We need advice on how to fix this problem before all our clients abandon is. The only clue we have is that there are 100s of these processes: 30 13205 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue 30 13207 1 0 11:38 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue 30 13208 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10026 before-remote 30 13209 1 0 11:38 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10026 before-remote 30 13213 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue

  Read the article

• Batch file to uninstall all Sun Java versions?

  - by Ricket

  I'm setting up a system to keep Java in our office up to date. Everyone has all different versions of Java, many of them old and insecure, and some dating back as far as 1.4. I have a System Center Essentials server which can push out and silently run a .msi file, and I've already tested that it can install the latest Java. But old versions (such as 1.4) aren't removed by the installer, so I need to uninstall them. Everyone is running Windows XP. The neat coincidence is that Sun just got bought by Oracle and Oracle has now changed all the instances of "Sun" to "Oracle" in Java. So, I can conveniently not have to worry about uninstalling the latest Java, because I can just do a search and uninstall all Sun Java programs. I found the following batch script on a forum post which looked promising: @echo off & cls Rem List all Installation subkeys from uninstall key. echo Searching Registry for Java Installs for /f %%I in ('reg query HKLM\SOFTWARE\microsoft\windows\currentversion\uninstall') do echo %%I | find "{" > nul && call :All-Installations %%I echo Search Complete.. goto :EOF :All-Installations Rem Filter out all but the Sun Installations for /f "tokens=2*" %%T in ('reg query %1 /v Publisher 2^> nul') do echo %%U | find "Sun" > nul && call :Sun-Installations %1 goto :EOF :Sun-Installations Rem Filter out all but the Sun-Java Installations. Note the tilda + n, which drops all the subkeys from the path for /f "tokens=2*" %%T in ('reg query %1 /v DisplayName 2^> nul') do echo . Uninstalling - %%U: | find "Java" && call :Sun-Java-Installs %~n1 goto :EOF :Sun-Java-Installs Rem Run Uninstaller for the installation MsiExec.exe /x%1 /qb echo . Uninstall Complete, Resuming Search.. goto :EOF However, when I run the script, I get the following output: Searching Registry for Java Installs 'DEV_24x6' is not recognized as an internal or external command, operable program or batch file. 'SUBSYS_542214F1' is not recognized as an internal or external command, operable program or batch file. And then it appears to hang and I ctrl-c to stop it. Reading through the script, I don't understand everything, but I don't know why it is trying to run pieces of registry keys as programs. What is wrong with the batch script? How can I fix it, so that I can move on to somehow turning it into a MSI and deploying it to everyone to clean up this office? Or alternatively, can you suggest a better solution or existing MSI file to do what I need? I just want to make sure to get all the old versions of Java off of everyone's computers, since I've heard of exploits that cause web pages to load using old versions of Java and I want to avoid those.

  Read the article

• Some services refusing to start on Win 7 machine. What could the root cause be?

  - by BombDefused

  When I check msconfig, there are no services that are blocked from starting up. When I look in services.msc, the problem services have a start up type of 'Automatic', but have a blank space where others will show 'Started'. Attempting to start them manually results in the following pop up error messages. I have no idea what's causing this, looks like some sort of cascade effect from another problem service. It's affecting scheduled tasks, SQL server agent and windows back up services. How can I resolve this? I don't know how to work out what the root cause is. Task Scheduler Service Start Error: "Windows could not start the Task Scheduler service on local computer. 1068: The dependecy service or group failed to start. SQL Server Service Start Error: "The SQL Server Agent service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs." UPDATE: I've just noticed some other services have a description of "Failed to Read Description. Error Code: 2" They are: NetMsmqActivator, NetPipeActivator, NetTcpActivator, NetTcpPortSharing UPDATE 2: As joeqwerty says the Event Log service does seem to be the root of the problem. This service will not start either. It fails with 'Error 31 - A device attached to the system is not functioning correctly'. I've tried detaching all devices. I've also followed the advice here, where the same problem is described, but with no luck: http://social.technet.microsoft.com/Forums/en/w7itprosecurity/thread/44479c49-55e6-4bd7-b25e-3f2a6497306e Update 3 @ Pacey - The following was a good tip, really clear instruction. However, I found that those reg keys do not exist on my system. "Your Problem might also derive from the UpperFilter or LowerFilter Settings of the CDROM Drive. These are a known cause for Errorcode 31. You can find step-by-step instructions on removing the filters on about.com" I followed the advice through to checking every component in device manager separately, but everything is reported as working correctly!? These services did all work at one point. The hardware set up hasn't changed much. Guess I'm looking at a repair install maybe???!

  Read the article

• Why does my computer run slowly and freeze sometimes?

  - by Brae

  EDIT I disabled sound in the BIOS, rebooted and it hung. I removed the (previously) faulty HDD, rebooted and it hung. I have managed to get my Realtek audio manager open again after its mysterious disappearance. Subsequently my microphone is now working again, to fix it I had to uninstall audio drivers, disable audio in BIOS, install audio drivers, enable audio in BIOS. Access via network (with faulty HDD in) seems to not be triggering hangs at the moment. I think with the sound problem fixed it might play a little nicer, but I think its still going to hang. If it does, then I'm fairly sure its been narrowed down to the mobo. EDIT Pretty convinced my motherboard is the culprit, because nothing else seems to have any obvious problems (bar the hard drive, which the PC still hangs without it being plugged in) So thank you all for helping, once I get more rep ill up a few of the answers. My PC is doing some weird things... Sometimes when I open up a program, lets say Adobe Photoshop, it will load everything normally, nice and quick no problems and I can use it fine. Other times its a little odd, and it loads the program as if it's only using half of the CPU. It's pretty obvious when it does it, normally the loading screen skims past, but when it does this weird load you see it slowly tick though each thing, and the program itself becomes incredibly slow. Even Google Chrome does it sometimes. Yet when I exit and reopen the program without doing anything else, it typically opens fine without lagging. I think this problem is probably a symptom of something bigger, because of other problems I'm having. Random hangs; no matter what I have open or what I'm doing. My PC will sort of freeze up for a few seconds. If music is playing it will either loop the last second or two, or it will buzz. This only lasts for a few seconds then it returns to normal without having to restart. During this time all programs lock up and freeze, and the mouse and keyboard are useless. I am also having a weird issue with my audio jacks, without touching my PC at all, sometimes I will see a popup saying that I have unplugged something or plugged something in, neither of which has actually happened. Pretty sure this is cause by the motherboard. I recently had a 'Pink Screen of Death' (yes pink) which pointed to my audio drivers. The lockups seem to happen with some consistency when someone is accessing my shared files via my home LAN. Which leads me to believe either one of my hard drives is acting up or more likely the controller. One of my drives had a bit of a crash before, I used Spinrite and managed to recover my stuff and now the drive appears to be working okay. This is possibly adding to the problems. My best guess is something has gone wrong with my motherboard, possibly a power issue or a chip has died, I really don't know. So what I would like to know is: Have I have missed some obvious diagnostic to help figure out what it is, or should I just bite the bullet and assume its my motherboard acting up and buy a new system? dxdiag[64-bit] - http://pastebin.com/G30kb2TL PSOD (minidump) - http://pastebin.com/aZsv0H56 HWiNFO64 (system info / specs) - http://pastebin.com/X6h3K8g6

  Read the article

• Can't Move Windows to 2nd Monitor without Left Mouse and Cntl Key

  - by John C

  I have 2 very frustrating problems that maybe someone can help me with: I have 2 monitors (different sizes and resolutions) setup with the "Extended" monitor Win7 setup. My problem is this = I can not "move" a window from my Primary Monitor (larger and higher resolution on right side in front of me) to my Secondary 2nd monitor (smaller and lower resolution) with just selecting the title bar with the left mouse button and dragging it to the left. Windows 7 "snaps" it back to the left Primary Monitor when the window is physically in the 2nd window area as I'm holding the left mouse button. I can prevent this problem - by holding down the Cntl Key with the Left Mouse button, but this is extremely annoying to me. Also I typically "lose" focus if I try typing input on the 2nd monitor. Typing is erratic with regard to keystroke accuracy from my keyboard translated into input on the 2nd screen. No problem with typing input on the primary left monitor. I find this extremely annoying in Windows 7 and turning off the "snap" feature via the Control panel does NOT work for me. Win7 stubbornly refuses to move my selected window to my 2nd monitor without me "forcing" Win7 to do this with the Cntrl Key. Please tell me this is not a Win7 feature. Also on my system - Windows Key + Shift, Left arrow Key (pressed together) or the same combo with The Right arrow Key - don't do anything whatsoever. Widows Key with "+" however does maximize current window across both monitors, and I can "restore" it with Windows Key and "-" back to original monitor and size. I have tried various solutions including changing the resolutions of one or both of my monitors and sometimes "temporarily helps" but reverts back to the problem. Also if I swap the logical (not physical) layout so that I tell Win7 the monitors are setup in a reserved situation (Large monitor on the left, and small on the right) - this also sometimes helps for awhile - and is very strange and awkward to work with "backwards". But all of these solutions stop working. The only solution that consistently works for "moving" the screens is to hold the Cntrl Key down as I'm moving window with the left mouse selected on the title bar. Even that however, doesn't prevent the loss of typing focus for me on the 2nd monitor - while at the same time the typing on the 1st monitor is fine. Any help on moving my window screens from one monitor on my 2nd monitor without having to press the Cntrl key while holding down my left mouse button with be appreciated. Also any help on gaining typing "focus" into my 2nd screen with be helpful too. Thanks - John

  Read the article

• What the best way to achieve RPO of zero and lowest possible RTO (less than 15 minutes) with SQL 2008 R2?

  - by Adrian Hope-Bailie

  We are running a payments (EFT transaction processing) application which is processing high volumes of transactions 24/7 and are currently investigating a better way of doing DB replication to our disaster recovery site. Our current and previous strategies have included using both DoubleTake and Redgate to replicate data to a warm stand-by. DoubleTake is the supported solution from the payments software vendor however their (DoubleTake's) support in South Africa is very poor. We had a few issues and simply couldn't ever resolve them so we had to give up on DoubleTake. We have been using Redgate to manually read the data from the primary site (via queries) and write to the DR site but this is: A bad solution Getting the software vendor hot and bothered whenever we have support issues as it has a tendency to interfere with the payment application which is very DB intensive. We recently upgraded the whole system to run on SQL 2008 R2 Enterprise which means we should probably be looking at using some of the built-in replication features. The server has 2 fairly large databases with a mixture of tables containing highly volatile transactional data and pretty static configuration data. Replication would be done over a WAN link to a separate physical site and needs to achieve the following objectives. RPO: Zero loss - This is transactional data with financial impact so we can't lose anything. RTO: Tending to zero - The business depends on our ability to process transactions every minute we are down we are losing money I have looked at a few of the other questions/answers but none meet our case exactly: SQL Server 2008 failover strategy - Log shipping or replication? How to achieve the following RTO & RPO with logshipping only using SQL Server? What is the best of two approaches to achieve DB Replication? My current thinking is that we should use mirroring but I am concerned that for RPO:0 we will need to do delayed commits and this could impact the performance of the primary DB which is not an option. Our current DR process is to: Stop incoming traffic to the primary site and allow all in-flight transaction to complete. Allow the replication to DR to complete. Change network routing to route to DR site. Start all applications and services on the secondary site (Ideally we can change this to a warmer stand-by whereby the applications are already running but not processing any transactions). In other words the DR database needs to, as quickly as possible, catch up with primary and be ready for processing as the new primary. We would then need to be able to reverse this when we are ready to switch back. Is there a better option than mirroring (should we be doing log-shipping too) and can anyone suggest other considerations that we should keep in mind?

  Read the article

• How do I tell mdadm to start using a missing disk in my RAID5 array again?

  - by Jon Cage

  I have a 3-disk RAID array running in my Ubuntu server. This has been running flawlessly for over a year but I was recently forced to strip, move and rebuild the machine. When I had it all back together and ran up Ubuntu, I had some problems with disks not being detected. A couple of reboots later and I'd solved that issue. The problem now is that the 3-disk array is showing up as degraded every time I boot up. For some reason it seems that Ubuntu has made a new array and added the missing disk to it. I've tried stopping the new 1-disk array and adding the missing disk, but I'm struggling. On startup I get this: root@uberserver:~# cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md_d1 : inactive sdf1[2](S) 1953511936 blocks md0 : active raid5 sdg1[2] sdc1[3] sdb1[1] sdh1[0] 2930279808 blocks level 5, 64k chunk, algorithm 2 [4/4] [UUUU] I have two RAID arrays and the one that normally pops up as md1 isn't appearing. I read somewhere that calling mdadm --assemble --scan would re-assemble the missing array so I've tried first stopping the existing array that ubuntu started: root@uberserver:~# mdadm --stop /dev/md_d1 mdadm: stopped /dev/md_d1 ...and then tried to tell ubuntu to pick the disks up again: root@uberserver:~# mdadm --assemble --scan mdadm: /dev/md/1 has been started with 2 drives (out of 3). So that's started md1 again but it's not picking up the disk from md_d1: root@uberserver:~# cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md1 : active raid5 sde1[1] sdf1[2] 3907023872 blocks level 5, 64k chunk, algorithm 2 [3/2] [_UU] md_d1 : inactive sdd1[0](S) 1953511936 blocks md0 : active raid5 sdg1[2] sdc1[3] sdb1[1] sdh1[0] 2930279808 blocks level 5, 64k chunk, algorithm 2 [4/4] [UUUU] What's going wrong here? Why is Ubuntu trying to pick up sdd into a different array? How do I get that missing disk back home again? [Edit] - After adding the md1 to mdadm.conf it now tries to mount the array on startup but it's still missing the disk. If I tell it to try and assemble automatically I get the impression it know it needs sdd but can't use it: root@uberserver:~# mdadm --assemble --scan /dev/md1: File exists mdadm: /dev/md/1 already active, cannot restart it! mdadm: /dev/md/1 needed for /dev/sdd1... What am I missing?

  Read the article

• Wirelss card not being detected in backtrack 5

  - by Jesse Nelson

  I just installed backtrack 5 and I am unable to detect my wireless card. iwconfig doesn't list my interface. I can see that the hardware is present in lspci -vnn (see below) but I can't get the interface detected. I have tried to reinstall the compat-wireless package but I get errors during the build (see below) I have done a ton of researching and I keep hitting a brick wall, mostly because the wiki for backtrack is down and I can't find any good resources. Does anyone know how to fix the issue? Also, does anyone no how I can scan the hardware to determine what NIC is assigning my interface? If I can figure out the interface name I think I can set it up manually by putting up the link and using wireless-tools to manually configure the connection, this is what I had to do in arch on my mac. As stated the wiki for backtrack is down and I can't find any help on the issue. I tried to do the full kernel upgrade suggested in my software update but after the update was complete and I logged back in I had a new log in manager and the only thing I was able to log into was window managers. However, after this update my wireless was working fine. Please help I am new to Linux and the wiki is down, I have nowhere else to turn. Forgot to mention I am using the KDE version, not Gnome. Thanks in advance for any help or support. Attempt at make: root@bt:/usr/src/compat-wireless-3.3-rc1-2# make /usr/src/compat-wireless-3.3-rc1-2/config.mk:254: "WARNING: CONFIG_CFG80211_WEXT will be deactivated or not working because kernel was compiled with CONFIG_WIRELESS_EXT=n. Tools using wext interface like iwconfig will not work. To activate it build your kernel e.g. with CONFIG_LIBIPW=m." make -C /lib/modules/2.6.38/build M=/usr/src/compat-wireless-3.3-rc1-2 modules make: *** /lib/modules/2.6.38/build: No such file or directory. Stop. make: *** [modules] Error 2 lspci output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn -i net lspci: I/O error at net, line 0 root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn 02:00.0 Network controller [0280]: Atheros Communications Inc. Device [168c:0032] (rev ff) (prog-if ff) !!! Unknown header type 7f ( This is the problem but I can't find the solution) Kernel modules: ath9k iwconfig output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• How to configure DD-WRT routing table when creating an isolated network segment for PCI C VT compliance

  - by tetranz

  I'm the volunteer support and system admin person at a small private school. We need to setup a PCI compliant Windows PC as a virtual terminal for credit card processing. I've read questionnaire SAQ C-VT and, to quote, this computer needs to be accessed: "via a computer that is isolated in a single location, and is not connected to other locations or systems within your environment (this can be achieved via a firewall or network segmentation to isolate the computer from other systems)" Our setup is as follows: DSL modem from ISP is setup to be a "transparent pipe" with no extra services. That goes into the WAN port of Linksys WRT54-GL running a DD-WRT. The LAN is 192.168.1.x. There are a couple of other WRT54-GL / DD-WRT devices. One is used as a wireless AP and another is a client bridge. To isolate the VT (virtual terminal) machine, I have another DD-WRT device. Its WAN is connected to a port on the 192.168.1.x LAN. The virtual terminal machine is connected to its LAN which is at 192.168.10.x. The SPI Firewall etc is turned on. It's basically the default DD-WRT gateway setup where the "ISP" is our own LAN. That's working. All incoming traffic to the VT machine is blocked, including from our own LAN. The VT can access the internet BUT, and here's the problem, it can also ping any of the computers on the 192.168.1.x LAN. I think I need to stop that. I'm guessing that I could do something with the Static Routing table in the VT machine's DD-WRT device. I need to route anything going to 192.168.1.x other than the gateway which is 192.168.1.1 to 0.0.0.0 or something like that. That's where I'm stuck at the end of my knowledge. Or ... do I need to get yet another DD-WRT so the network is "balanced". Maybe I need to have the internet from the DSL going into a DD-WRT which has only two devices on its LAN i.e., two other DD-WRTs, one for the main LAN and one for the VT. I think that would do but I'd like to avoid the extra cost and complexity if I don't need it. Thanks

  Read the article

• Can this USB3 behaviour be anything else than a hardware failure?

  - by Jonas Wielicki

  While my motherboard is half a year old now (ASUS M5A99X EVO), I only recently made use of the USB3 boards (after purchase of USB3 external harddrive). However, I am encountering issues. I am running linux 3.6.7-4.fc16.x86_64. Initially, the harddrive worked fine with USB3 (amazing ˜160MB/s), but I had some problems after putting after putting the harddrive to sleep manually after use (backup) with hdparm -Y. After some time, the device disappears from lsusb and i see the following in dmesg: [ 1924.091107] xhci_hcd 0000:05:00.0: xHCI host not responding to stop endpoint command. [ 1924.091114] xhci_hcd 0000:05:00.0: Assuming host is dying, halting host. [ 1924.091147] xhci_hcd 0000:05:00.0: HC died; cleaning up [ 1924.091233] usb 11-1: USB disconnect, device number 2 [ 1924.091272] sd 6:0:0:0: Device offlined - not ready after error recovery Testing with my (USB3 capable) notebook, I could not immediately reproduce the behaivour. I put the drive to sleep with hdparm -Y and waited for like an hour, but it was still listed in lsusb and responded after a few seconds delay when I tried after the hour of waiting. After an hour, on the desktop, the device would've usually vanished. Googling for this issue, I came across hints that playing around with IOMMU settings and upgrading the BIOS might help. I upgraded the BIOS and tried both with and without IOMMU enabled, got similar results. Most disturbing is, that one of the two USB 3.0 hubs sometimes also disappears from lsusb (or does not show up after boot at all). I've also heard that there are some hardware issues with ASUS USB3 ports. Applying mechanic force to the capble doesn't push the issue to one side or the other. Also, udev seems to reenumerate all devices if I plug the HDD into the USB 3.0 port without success (I can notice from my keyboard layout being changed to the default, which I do not use normally). The drive is externally powered and the external power supply is plugged in (it also stays powered when unplugging from USB, although it will spin down then). So before I try to return the board, I wanted to find out whether this can be anything else than a failure on the motherboard?

  Read the article

• Pairing Bluetooth device with PIN fails

  - by Pikaro

  I'm trying to pair my old BlackBerry 8310 to my Linux desktop (up-to-date Debian Sid, 3.15-10.dmz.1-liquorix-amd64) by using blueman and its associated tools. Scanning for the device works equally well for both sides; however, I am unable to pair the two once it comes to entering the PIN. If I scan from my PC, I have two options in blueman-manager regarding my phone: Directly selecting "pair", or selecting "setup". If I select "pair", nothing happens on my desktop, but the phone asks me to enter a PIN; if I do so, it reports that pairing has failed. During that, nothing is logged to the console. Selecting "setup" opens a configuration dialog that allows for entering or generating a PIN. Regardless, I get to a screen that tells me to enter the PIN on the phone, and at the same time, the phone pops up the equivalent dialog. This would be what one would expect to work; but whatever I enter (naturally, the same on both), both devices report that pairing has failed, and blueman-manager logs init_services (/usr/lib/python2.7/dist-packages/blueman/main/Device.py:73) Loading services org.bluez.Error.AuthenticationFailed: Authentication Failed If I instead try to pair from the phone, I cannot see any kind of reaction from my desktop - all I get is the equivalent "pairing failed" message from the BlackBerry after I entered a PIN in the dialog that pops up there. hcitool scan and hciconfig -a work without complaints, but I cannot find a way to try the pairing as a whole on the console since bluez-simple-agent seems to have been discontinued and this recommendation is everywhere on Google. hcitool cc as root opens the PIN dialog on the phone, then fails with "Input/Output error" once I enter it. The user is not permitted to execute this command. I also tried creating /usr/lib/bluetooth/<MAC>/pincodes to manually define a persistent PIN, which seems to have had no effect. The same goes for running the different commands as root, though I'm really confused about the internal structure of the Bluetooth subsystem now: They usually and inconsistently failed with Python or DBUS errors or just showed the same results. The only other Bluetooth device I have around are a pair of Creative speakers. Trying "setup" asks me to enter a key on them, which is impossible. If I try "pair", I'm asked for a PIN as I should, but no pairing takes place, and no errors appear on the console. (It just repeats their name a few times.) Interestingly, I tried that before writing my question, and nothing happened in terms of PIN questions, just like with the BlackBerry, which still shows no change. I don't think I actively changed anything since then. The BlackBerry can pair with and connect to the speakers, and everything goes as one would expect, so the problem is definitely with my desktop. So thus my questions: What is that PIN window generated by, and why does it seem to appear randomly? How can I find out what, exactly, fails after trying to add the speakers, as this may give me a clue? Is there any kind of complete log that concerns itself with Bluetooth? What data can I provide to make this more solvable?

  Read the article

• Vista 64-bit, DISK BOOT FAILURE

  - by weka

  So I have this Acer Aspire AX3200-U3600A with Windows Vista (64-bit). Every night I turn it off and turn it back on in the morning. Around three weeks ago, I did a fresh factory reimage. Good as new. Then around two days ago, when I turned it on, I noticed it was running extremly slow. As in, it would often freeze up while I had multiple applications open when it usually never froze up. So I decided to restart my computer. Big mistake. My computer froze right after I clicked shut-down. I waited a while. Nothing. Waited some minutes. Nope. I decided to shut it down by pressing the power button. Here is where the problems begin. When I turned it back on, I saw the Windows logo and loading bar and then it loaded to black. I turned it off again forcefully by power button and then once more... then I got: AMD Data Change... Update New Data to DMI! then later the screen clears and I get: AHCI Option ROM BIOS Revision: 01.05.92 Date: 02-19-2008 Copyright (c) 2006-2008 Phoenix Technologies, LTD Port 01: Reset Port Error!! Port 02: then the screen clears again but this time, this loads from the bottom: Nvidia Boot Agent 249.0542 (copyright stuff... blah blah) PXE-E61: Media test failure, check cable. PXE-M0F: Exiting Nvidia Boot Agent DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER. So I try to go into Safe Mode. Well, first of all it doesn't load as fast. After it loads disk.sys from windows/drivers, it will wait a while (2-3 mins) THEN load. However it loads the Acer eRecovery Management Tool. I have three options: Reset computer to factory default, Restore computer from user's backup, or Exit. However, the top two options are gray and disabled where as the Exit is in blue and definitely clickable. So obviously safe mode is not there... A strong thing to note: In the beginning when all of this started, I did a Boot Windows Normal from pressing f8 and I got to my desktop! It logged me in. I could see the icons on my files. However my desktop was extremely slow as in when I clicked on the Start menu, it would wait a while, then load up the menu with JUST the gradient, no text or icons... so as you can see... it saw my HDD? Also, before anyone says, I have NO USB plugged in. My mouse and keyboard are not USB inputs, I assure you. And this came without a recovery CD AND when I went in BIOS, to change the BOOT ORDER, I did NOT see a CD-ROM option. And when I tried pressing ALT+F10 to get into Acer eRecovery Management, the top two options were disabled as well. But sometimes on start-up, I get: Windows has encountered a problem communicating with a device connected to your computer. This error can be caused by unplugging a removable storage device such as an external USB drive while the device is in use, or by faulty hardware such as a hard drive or CD-ROM drive that is failing. Make sure any removeable storage is properly connected and then restart your computer. If you continue to receive this error message, contact the hardware manufacturer. Status: 0xc00000e9 Info: An unexpected I/O error has occured. Then I tried Last Known Good Configuration Settings, that gives me a BSOD. What should I do/

  Read the article

• Both nginx and php5-fpm init.d startup scripts are non-functional and returning no errors..? But they used to work perfectly

  - by Ollie Treend

  I have been using nginx and php5-fpm on my Ubuntu box for a while now. Everything has been configured and setup correctly, and it ran like a charm. I have been keeping the packages updated & upgraded as usual, but haven't touched the nginx OR php5-fpm config files at all (thus I'm pretty sure this isn't my fault... ) Basically, I noticed nginx wasn't running as it should be. I ran the command sudo service nginx start, and the script did nothing. The same thing happens when trying to do anything - start, stop, restart or reload. This also happens for the "php5-fpm" init script - although all other init scripts seem to be functioning correctly. When trying to start nginx OR php5-fpm, this is what happens: root@HAL:/etc# service php5-fpm start root@HAL:/etc# I can't understand what is going wrong. The script isn't returning errors, but similarly it isn't starting the daemon or reporting success as usual. For reference, both installations are from the official nginx and php5-fpm PPAs. The fact that both started doing this at the same time has thrown me - since they are both unrelated packages. I have since purged both sets of packages from my system with apt-get purge ... and also apt-get remove --purge ... both of which have successfully removed the packages, their config files, and their init.d startup scripts. After having reinstalled nginx, I now have a functioning startup script again - I can start the web server as usual. However, php5-fpm is still experiencing the strange premature exiting of the startup script.. and I really can't figure out what's causing it. I have no idea what caused this to occur initially, but have managed to fix nginx. I now need to fix the php5-fpm startup script. If anybody could shed some light on this situation, I would be very grateful! The chances are both these issues are related - and they were caused by me doing something stupid. But now I need to fix it. This time I was lucky - because these problems are just on my development server. But I have 2 other live servers which are configured in a similar way, and I am worried the same thing will happen to these two as well! Has anybody else come across this? Do you have any words of advice? Thank you

  Read the article

• How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files)

  - by user11955

  Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

  Read the article

• Computer suddenly dies; screen displays weird flickering lines, then restarts

  - by Imray

  I've been having this terrible problem for a little while and just managed to get a picture of 'dead screen' for the first time and I am posting it to seek help. Randomly, at irregular intervals (typically once a week), while working on something (it's been different things every time) my computer will just suddenly go dead - the screen turns to exactly the picture below (the lines flicker a little bit), it hangs there for a few seconds and then restarts. Obviously this is extremely frustrating and I want to try to stop it. I've searched numerous postings with similar keywords but nothing exactly the same as mine. Does anyone have any idea what might be the cause of this? I would post all my system settings and installed programs but the list is long and I don't know how much relevance each item would be. If you'd like to know something specific, please comment and I'll let you know whatever you need. SPECS C:\Users\Imray>systeminfo Host Name: Imray OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Workstation OS Build Type: Multiprocessor Free Registered Owner: Imray - Owner Registered Organization: Product ID: 00371-152-9333854-85895 Original Install Date: 06/09/1999, 5:45:21 PM System Boot Time: 22/03/2013, 8:58:18 AM System Manufacturer: Gateway System Model: DX4840 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 37 Stepping 2 GenuineIntel ~3201 Mhz BIOS Version: American Megatrends Inc. P01-A3 , 17/05/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume2 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 6,135 MB Available Physical Memory: 3,632 MB Virtual Memory: Max Size: 12,268 MB Virtual Memory: Available: 8,114 MB Virtual Memory: In Use: 4,154 MB Page File Location(s): C:\pagefile.sys Domain: WORKGROUP Logon Server: \\Imray-OWNER Hotfix(s): 4 Hotfix(s) Installed. [01]: KB971033 [02]: KB958559 [03]: KB977206 [04]: KB981889 Network Card(s): 2 NIC(s) Installed. [01]: 802.11n Wireless PCI Express Card LAN Adapter Connection Name: Wireless Network Connection DHCP Enabled: Yes DHCP Server: 192.168.2.1 IP address(es) [01]: 192.168.2.13 [02]: fe80::1df1:5399:6890:91f6 [02]: Microsoft Virtual WiFi Miniport Adapter Connection Name: Wireless Network Connection 2 DHCP Enabled: Yes DHCP Server: N/A IP address(es) Graphics Card Specs Name ATI Radeon HD 5570 PNP Device ID PCI\VEN_1002&DEV_68D9&SUBSYS_E142174B&REV_00\4&18A4B35E&0&0008 Adapter Type ATI display adapter (0x68D9), ATI Technologies Inc. compatible Adapter Description ATI Radeon HD 5570 Adapter RAM 1.00 GB (1,073,741,824 bytes) Installed Drivers atiu9p64 aticfx64 aticfx64 atiu9pag aticfx32 aticfx32 atiumd64 atidxx64 atidxx64 atiumdag atidxx32 atidxx32 atiumdva atiumd6a atitmm64 Driver Version 8.700.0.0 INF File oem1.inf (ati2mtag_Evergreen section) Color Planes Not Available Color Table Entries 4294967296 Resolution 1920 x 1080 x 59 hertz Bits/Pixel 32 Memory Address 0xD0000000-0xDFFFFFFF Memory Address 0xFBDE0000-0xFBDFFFFF I/O Port 0x0000D000-0x0000DFFF IRQ Channel IRQ 4294967293 I/O Port 0x000003B0-0x000003BB I/O Port 0x000003C0-0x000003DF Memory Address 0xA0000-0xBFFFF Driver c:\windows\system32\drivers\atikmpag.sys (8.14.1.6095, 181.00 KB (185,344 bytes), 06/09/1999 5:59 PM)

  Read the article

• Why is BIND giving me a SERVFAIL in this case? (Notes inside)

  - by imaginative

  Woke up this morning to a bunch of the following: root@foo:/etc/bind# dig @1.2.3.4 foo.example.com ; <<>> DiG 9.6.1-P2 <<>> @1.2.3.4 foo.example.com ; (1 server found) ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 36121 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;;foo.example.com. IN A ;; Query time: 0 msec ;; SERVER: 1.2.3.4#53(1.2.3.4) ;; WHEN: Thu Apr 1 09:57:59 2010 ;; MSG SIZE rcvd: 31 Some background on the fictitious "1.2.3.4". It's a slave name server in my nameserver "farm". Technically I have ns1 (being the master) and ns2/ns3. Currently ns1/ns2 are down for maintenance, so I left ns3 at it serving live traffic. That's the point, DNS is supposed to be resilient. Now the odd part is, "1.2.3.4" was serving requests for example.com just fine for the last 4-5 days. This morning I get a phone call that it's non-responsive. After investigation I see the message you see above, SERVFAIL. I looked into the zone file and saw the following: example.com IN SOA ns1.example.com. hostmaster.mail.example.com. ( I wondered if at this point that the nameserver thought it was not authoritative over example.com and adjusted it to the following: example.com IN SOA ns3.example.com. hostmaster.mail.example.com. ( After that, it started responding again for all authoritative queries for example.com. I have no idea why. I thought these things were supposed to be normalized upon zone transfer from ns1 - ns3? Can someone please example why this happened and how to prevent it from happening in the future? I've never had a similar problem, and because I don't understand it well, I might be missing some critical information in this question. So please let me know if I can further add any detail to make things clearer as well. One more thing to note: I have other domains that I'm authoritative for that have their SOA still saying ns1.example.com. and not ns3.example.com. Those domains are serving requests just fine! Is it a matter of time before they stop also and I have to change SOA to ns3.example.com? Is this also only required because ns1 and ns2 are currently offline?

  Read the article

• Windows 7 is stuck at "Starting Windows" when I attempt to boot computer

  - by Eli

  Basically, whenever I turn on my computer, it gets to the Starting Windows phase and just stays there. The startup animation still plays, yet it gets nowhere. I have tried booting into safe mode, however it gets stuck at loading CLASSPNP.SYS. It then freezes there and doesn't continue booting. I have tried booting into recovery mode from the hard drive, and it freezes after displaying the background image. I have tried booting from a recovery CD, which works, and I was able to use system restore. However, using system restore did not fix it, and it still is stuck at the Starting Windows screen. I have tried booting a Windows CD (Windows 8 Retail Installer) to see if I could upgrade it to fix this issue, however that froze at a blank screen after it got past the boot logo. I have tried changing around the BIOS settings (including resetting), to no avail. I have tried re-plugging the internal PSU cables (this is a custom-built desktop), yet this has changed nothing. I can boot into a loopback Ubuntu install on the same drive, which works fine, other than the fact that it has issues with some of the USB ports and the network card. This system has worked fine for the past few months, completely stable, and nothing in the configuration has changed before this error started happening. Startup Repair on the Windows recovery CD doesn't find any issues. Unplugging my secondary hard drive or swapping around memory doesn't change anything. The hard drive itself is fine, it hasn't shown any signs of failure and once again, boots my other OS fine. If anyone could help with this, that would be great. I can't seem to find any possible solution to this. If it makes any difference, my system specs are as follows: AMD FX-8320 Gigabyte GA-970A-D3 4GB of DDR3 Radeon HD 6870 550w PSU I'd like to not have to reinstall Windows, for I have more than a terabyte of data that I would have to back up if that becomes the only option. EDIT: I have since tried the following: Tried the solution involving restoring files from RegBackup, which changed nothing. Tried testing everything with Hiren's boot CD, everything comes back as fine. Tried disabling everything unnecessary in the BIOS and unplugging everything unneeded, it still hangs. Tried swapping out every possible combination of RAM, it still has the same result. The RAM is not at fault it seems Tried every GPU I own (which is many!) and it still hangs at the exact same place. Tried minimizing the power consumption as much as possible, even using an old PCI graphics card. It still hangs at the same place in the same way, signifying that it's not the PSU at fault. Tried resetting the BIOS again, still nothing. Tried every possible combination of BIOS options, even downclocking everything, it still hangs in the same spot. Tried upgrading the BIOS from version FB to FD, which changed nothing. Based on this, I would conclude the motherboard to be at fault. Are there any other possibilities? I don't want to spend $150 for a new motherboard. EDIT 2: This is what it gets stuck at when I try to boot into safe mode: Note the slight graphical corruption at the top of the screen. No matter how I set up the system, this seems to be there. In addition, either it has stopped booting into safe mode now, or it takes upwards of 2+ hours, and I haven't left it running for that long.

  Read the article

• USB connection is unstable with Nexus S 2.3.4 on AMD 64 running 64-bit Windows 7, but works with 32-bit Windows Vista

  - by Mike

  The USB connection is unstable with Nexus S (Android 2.3.4) on AMD 64 running 64-bit Windows 7, but it works with 32-bit Windows Vista. Problem Description: On the 64-bit Windows 7 machine my Nexus S appears to connect, but then it disconnects moments later. Neither accessing USB storage or loading an Android application package file (APK) using the Android Debug Bridge (ADB) work. On 32-bit Windows Vista using the same USB cable, USB storage works. I haven't tried the ADB on 32-bit Windows Vista. Reproduction steps for USB storage: (I have provided the reproduction steps for USB storage and not ADB, because if one isn't working, then the other isn't working either and the USB storage reproduction steps are shorter to document.) Connect the USB cable to the Nexus S and my Windows 7 machine. Effect: The "USB Mass Storage, USB Connected" dialog appears with the button "Turn on USB storage." Click "Turn on USB Storage" Effect: The "working circle" appears. A dialog briefly appears saying "USB storage in use," then it either returns me to Step 1 (now that I am running 2.3.4) or is replaced with the Nexus S's application homepage (while I was running 2.3.3). I'm not sure if the version matters, but I mention it for completeness. On the 32-bit Windows Vista machine the connection is stable. I am able to navigate through the Nexus S file system create, read, update, and delete files, etc. I haven't tried connecting with the ADB. Troubleshooting summary: Tried and failed: Uninstalling and reinstalling the Android USB drivers including removing the files. Uninstalling my custom software Pulling the Nexus S's battery Restarting the Nexus S Restarting 64-bit Windows 7 Changing USB ports on the 64-bit Windows 7 box Compared the dates and file size on the DLLs in my google-usb_driver\amd64 directory and the windows\System32 directory. They match. The sizes for the google-usb_driver\i386 directory do not match (expected). Turning off Debugging mode on the Nexus S does not resolve the problem. Searching Google. Tried and succeeded: Connecting to another machine (Windows Vista) using the same USB cable and Nexus S phone. Troubleshooting observations: I notice that uninstalling the device drivers and deleting the files, then reinstalling the drivers, then rebooting 64-bit Windows 7 then unplugging the Nexus S, then plugging it back in occasionally helps for a short amount of time (minutes to hours, not days). When it is working, I can both access the Nexus S's drive and load/test applications using the ADB. I have observed some wonky behavior in the Device Manager that I haven't tracked down. Sometimes the black Nexus S image appears in the list of devices. Sometimes the image displays as a computer with a green ISA card. Sometimes it neither appears on the top level of devices nor under “other devices,” but it does appear under "disk drives" as "Android UMS Composite USB Device." System configuration: The Nexus S is running Android OS 2.3.4's "Settings\about phone\System updates" indicates that it is up to date as of May 21st 2011. Both 32-bit Windows Vista and 64-bit Windows 7 are up to date. The Windows Vista system is running on an Intel 32-bit processor. Windows 7 is running on an AMD 64-bit processor. I have done Android development on both systems, but I usually develop on the 64-bit Windows 7 machine.

  Read the article

• Cooling Server Rack with Water? Sensible? Reuse energy for small installation?

  - by TomTom

  First - this is not a shopping question, this is not so much about concrete prices but about general feasibility. Makes no sense to get looking fo ra manufacturer it the approach is bad. I am moving my company to new Offices in September, and among them we will expand and consolidate our number crunch cluster. It is so far in a data center. I have a nice room in the basement prepared now. I think about cooling. We will likely run up a power usage of around 10kw by end of the year. That is a LOT of stuff, and cooling will be expensive. I am located in south Poland, close to the German border. This is an area where water is available for relatively cheap price - "wasting water" is not a concern here. My situation is thus a lot different for example than in Spain ;) Physics tells me that to heat 1 liter of water by 1 degree I use 1 Calorie (1KCal), and a kwh power is (and we can assume 100% efficiency - water heaters are pretty efficient) 750 Calories. That means that 1 KWH is 750 liter by 1 degree. 10kw and a 20 degree heat would mean that per hour I need 375 liters. That is 6.25 liters per minute and not WHAT much ;) We talk 270 cubic meters here. Even in summer, the significant underground pipes really cool down the water a LOT more ;) Question: This such an approach feasible? Anyone done that? We talk of a 10kw installation for now. Is it feasible to reuse that heat? The alternative is a decent cooling system that WILL use around 2.5kwh for running. Dropping the water would basically (a) get me a quite cold input compared to the outside air even in summer (I.e. a lower temperature medium to drop the heat in) and (b) replace the need to actually have the outside cooling (which may b problematic - if the air is 22 degree, that is a LOT to fight off, but OTOH the water will be quite cold). I also would possibly save the investment for the outside part of the cooling circuit. Now, second question - is there a feasible way to heat a house with that? ;) After all, brutally speaking, it is a LOT of energy in that water ;) If it is a bad idea, I stop here - if it is not, I start looking for suppliers. Maybe my math is wrong?

  Read the article

< Previous Page | 538 539 540 541 542 543 544 545 546 547 548 549  | Next Page >