Search Results

Search found 24106 results on 965 pages for 'usb key'.

Page 542/965 | < Previous Page | 538 539 540 541 542 543 544 545 546 547 548 549  | Next Page >

  • Cannot enable Additional drivers for Broadcom in 12.10

    - by Compt
    tl;dr version: Additional Drivers does not work for enabling a driver in Ubuntu 12.10, however it worked in 12.04. I upgraded to Ubuntu 12.10 from 12.04 via a live USB. I did a fresh install to avoid any conflicts. From 12.04 I know that my wireless card has proprietary drivers that could be installed via Additional Drivers. I did eventually find additional drivers in the software sources menu, however when I attempt to switch to Broadcom 802.11 Linux STA wireless driver source from bcmwl-kernel-source, it not only does not work, it in fact disables my wireless completely. The only way to revert this is to restart, and revert back to "do not use the device". Then upon another restart, my wireless will function once again. I was curious if anyone else had this issue, and if there was a fix for it as of yet. I looked on launchpad and it may be a potential bug, but I am unsure. Any help would be greatly appreciated (and sorry for that wall of text). Until then, I'll continue to use my wireless as it is (or revert to 12.04), but I do notice a slower connection without it enabled.

    Read the article

  • recent unreliable wireless connection with Netgear KWGR614 router

    - by gabkdlly
    Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I know that this router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. Is it possible that someone is jamming my signal ?

    Read the article

  • Design pattern for an automated mechanical test bench

    - by JJS
    Background I have a test fixture with a number of communication/data acquisition devices on it that is used as an end of line test for a product. Because of all the various sensors used in the bench and the need to run the test procedure in near real-time, I'm having a hard time structuring the program to be more friendly to modify later on. For example, a National Instruments USB data acquisition device is used to control an analog output (load) and monitor an analog input (current), a digital scale with a serial data interface measures position, an air pressure gauge with a different serial data interface, and the product is interfaced through a proprietary DLL that handles its own serial communication. The hard part The "real-time" aspect of the program is my biggest tripping point. For example, I need to time how long the product needs to go from position 0 to position 10,000 to the tenth of a second. While it's traveling, I need to ramp up an output of the NI DAQ when it reaches position 6,000 and ramp it down when it reaches position 8,000. This sort of control looks easy from browsing NI's LabVIEW docs but I'm stuck with C# for now. All external communication is done by polling which makes for lots of annoying loops. I've slapped together a loose Producer Consumer model where the Producer thread loops through reading the sensors and sets the outputs. The Consumer thread executes functions containing timed loops that poll the Producer for current data and execute movement commands as required. The UI thread polls both threads for updating some gauges indicating current test progress. Unsure where to start Is there a more appropriate pattern for this type of application? Are there any good resources for writing control loops in software (non-LabVIEW) that interface with external sensors and whatnot?

    Read the article

  • Cloud Computing Pricing - It's like a Hotel

    - by BuckWoody
    I normally don't go into the economics or pricing side of Distributed Computing, but I've had a few friends that have been surprised by a bill lately and I wanted to quickly address at least one aspect of it. Most folks are used to buying software and owning it outright - like buying a car. We pay a lot for the car, and then we use it whenever we want. We think of the "cloud" services as a taxi - we'll just pay for the ride we take an no more. But it's not quite like that. It's actually more like a hotel. When you subscribe to Azure using a free offering like the MSDN subscription, you don't have to pay anything for the service. But when you create an instance of a Web or Compute Role, Storage, that sort of thing, you can think of the idea of checking into a hotel room. You get the key, you pay for the room. For Azure, using bandwidth, CPU and so on is billed just like it states in the Azure Portal. so in effect there is a cost for the service and then a cost to use it, like water or power or any other utility. Where this bit some folks is that they created an instance, played around with it, and then left it running. No one was using it, no one was on - so they thought they wouldn't be charged. But they were. It wasn't much, but it was a surprise.They had the hotel room key, but they weren't in the room, so to speak. To add to their frustration, they had to talk to someone on the phone to cancel the account. I understand the frustration. Although we have all this spelled out in the sign up area, not everyone has the time to read through all that. I get that. So why not make this easier? As an explanation, we bill for that time because the instance is still running, and we have to tie up resources to be available the second you want them, and that costs money. As far as being able to cancel from the portal, that's also something that needs to be clearer. You may not be aware that you can spin up instances using code - and so cancelling from the Portal would allow you to do the same thing. Since a mistake in code could erase all of your instances and the account, we make you call to make sure you're you and you really want to take it down. Not a perfect system by any means, but we'll evolve this as time goes on. For now, I wanted to make sure you're aware of what you should do. By the way, you don't have to cancel your whole account not to be billed. Just delete the instance from the portal and you won't be charged. You don't have to call anyone for that. And just FYI - you can download the SDK for Azure and never even hit the online version at all for learning and playing around. No sign-up, no credit card, PO, nothing like that. In fact, that's how I demo Azure all the time. Everything runs right on your laptop in an emulated environment.  

    Read the article

  • help download and install and save and use my wireless stick modem and software

    - by ADAM
    i installed Linux Ubuntu after my win os went totally dead by fatal blue screen. cannot reboot or install form CD ROM or get safe mode i installed Linux Ubuntu i still unable to install my wireless stick usb modem to connect and surf the Internet wireless form my provider. i use wireless network from neighborhood And i find it difficult to download and install and save porg and application from the INTERNET like skype and real player and others. it is different form windows and not that easy to use. i click to download for example and find real player but when click on it it opens as text file only and i cannot use it as it should be used for video and download and record from you tube. how to do it. and is there with Linux Ubuntu similar prog to download and record and save from you tube as in windows? Is there any trick to restart or reboot windows OS from the dead. can i use linux to reboot windows or to import my files from the blue screen stopped windows7? Any help is highly appreciated. thanks please email me to : [email protected]

    Read the article

  • News From EAP Testing

    - by Fatherjack
    There is a phrase that goes something like “Watch the pennies and the pounds/dollars will take care of themselves”, meaning that if you pay attention to the small things then the larger things are going to fare well too. I am lucky enough to be a Friend of Red Gate and once in a while I get told about new features in their tools and have a test copy of the software to trial. I got one of those emails a week or so ago and I have been exploring the SQL Prompt 6 EAP since then. One really useful feature of long standing in SQL Prompt is the idea of a code snippet that is automatically pasted into the SSMS editor when you type a few key letters. For example I can type “ssf” and then press the tab key and the text is expanded to SELECT * FROM. There are lots of these combinations and it is possible to create your own really easily. To create your own you use the Snippet Manager interface to define the shortcut letters and the code that you want to have put in their place. Let’s look at an example. Say I am writing a blog about something and want to have the demo code create a temporary table. It might looks like this; The first time you run the code everything is fine, a lovely set of dates fill the results grid but run it a second time and this happens.   Yep, we didn’t destroy the temporary table so the CREATE statement fails when it finds the table already exists. No matter, I have a snippet created that takes care of this.   Nothing too technical here but you will see that in the Code section there is $CURSOR$, this isn’t a TSQL keyword but a marker for SQL Prompt to place the cursor in that position when the Code is pasted into the SSMS Editor. I just place my cursor above the CREATE statement and type “ifobj” – the shortcut for my code to DROP the temporary table – which has been defined in the Snippet Manager as below. This means I am right-away ready to type the name of the offending table. Pretty neat and it’s been very useful in saving me lots of time over many years.   The news for SQL Prompt 6 is that Red Gate have added a new Snippet Command of $PASTE$. Let’s alter our snippet to the following and try it out   Once again, we will type type “ifobj” in the SSMS Editor but first of all, highlight the name of the table #TestTable and copy it to your clipboard. Now type “ifobj” and press Tab… Wherever the string $PASTE$ is placed in the snippet, the contents of your clipboard are merged into the pasted TSQL. This means I don’t need to type the table name into the code snippet, it’s already there and I am seeing a fully functioning piece of TSQL ready to run. This means it is it even easier to write TSQL quickly and consistently. Attention to detail like this from Red Gate means that their developer tools stay on track to keep winning awards year after year and help take the hard work out of writing neat, accurate TSQL. If you want to try out SQL Prompt all the details are at http://www.red-gate.com/products/sql-development/sql-prompt/.

    Read the article

  • Click buttons on the mouse stopped working in 12.10

    - by Kushal
    everything was great for a couple weeks after the upgrade, and then all of a sudden, the click buttons on my trackpad (as well as any other USB mouse I would hook up) stopped working. The pointer moves fine, but the clicks don't work. Sometimes the left click doesn't work but right click does, and then some times, neither works. I noticed this would begin when I would accidentally drag some text in a web browser (you know how when you try to move your pointer through the trackpad, but you accidentally tap down and it starts to drag whatever text you've selected on the window), and then you're done. The clicks won't work after that. They would work upon rebooting or logging off and back on, but then after a few minutes of usage, things would go back to being broken again. It happened a LOT when I was trying to play Scrabble on Facebook. I've raised a bug for this, but I haven't heard back anything on it. Here's the bug report: https://bugs.launchpad.net/bugs/1077805 Since the system was unusable this way, I had to remove it and install another OS based on 12.04. Has anyone else faced this issue or does someone know what to do to fix it? I'd go back to vanilla Ubuntu in a heartbeat if this issue can be fixed.

    Read the article

  • How do I get my programs to communicate with each other

    - by Benjamin Lindqvist
    I'm basically just getting started with programming. The problem I have with progressing is that I have a hard time learning stuff just for the sake of knowing them - I do better when there's a problem to be solved or a task to be completed so I can learn 'on the job'. So I'm interested in starting some interesting project. I know the basics of Python, Java, Matlab and some C++ aswell and I know enough about microcontrollers to make LED blink etc. The type of stuff I'm looking for is for example scraping some weather forecast site (with Python) and outputting the chance of rain to a LCD display, or a program that makes chrome open and log in to facebook if I say "HAL, time for facebook", or more generally, a program that reads serial/USB input, looks for certain sequences and sends instructions to some other program if it finds one. Do you open some kind of shared stream in which one program reads and one writes? What do I need to read up on to do accomplish this myself? I have no experience with linux or the linux terminal, but looking over peoples shoulders makes me suspect that's what people use. Is that correct?

    Read the article

  • How to configure Logitech Marble trackball

    - by user27189
    You can configure it using xinput. I tested this in 11.10 and it works very nicely. This selection is from "Ubuntuwiki" Avoid using Hal for this release because it has known issues. Put the following into terminal, using gedit: Edit $HOME/bin/trackball.sh using this command: gedit $HOME/bin/trackball.sh Then paste this into the file: #!/bin/bash dev="Logitech USB Trackball" we="Evdev Wheel Emulation" xinput set-int-prop "$dev" "$we Button" 8 8 xinput set-int-prop "$dev" "$we" 8 1 # xinput set-int-prop "$dev" "$we" 8 1 # xinput set-int-prop "$dev" "$we Button" 8 9 # xinput set-int-prop "$dev" "$we X Axis" 8 6 7 # xinput set-int-prop "$dev" "$we Y Axis" 8 4 5 # xinput set-int-prop "$dev" "Drag Lock Buttons" 8 8 Make sure trackball.sh begins with #!/bin/bash. Make the script executable by running this: chmod +x $HOME/bin/trackball.sh` Add the following lines to $HOME/.bashrc, using gedit $HOME/.bashrc and put this in the file even if it is empty: xmodmap $HOME/.Xmodmap > /dev/null 2>&1 $HOME/bin/trackball.sh Edit $HOME/.Xmodmap using: gedit $HOME/.Xmodmap pointer = 1 8 3 4 5 6 7 9 Log out and back in and viola!

    Read the article

  • Failure to Boot Windows 7 after Ubuntu install

    - by Mike
    My computer is a (brand new) PC notebook, without a CD drive running Windows 7. I followed this page to install from USB: https://help.ubuntu.com/community/Installation/FromUSBStickQuick The installation went well and i am using Ubuntu now (v. 12.04 i believe) I want to be able to dual boot Ubuntu and Win7 The problem is that the disc partitioning during the Linux install caused a problem with Windows, caused some problem with windows, and windows can no longer boot when i choose it at the GNU GRUB screen. When i restart my computer i can successfully boot Linux, but not Windows 7. At the GRUB screen - if i run Win7 normally, it freezes, shows a blue screen, and returns back to GRUB - if i run Win7 recovery, i dont know how to access the files that i need in order to run windows again, so nothing helpful happens. Can you please tell me what i would need to do(or link a guide) in order to run Windows again. (Windows and Linux is preferable, but if thats impossible going back to only Windows will help too) Im guessing the easiest thing to do is just to reinstall both OS, or is there anyway to undo the partition i made during the install? Thanks

    Read the article

  • GRUB2 not working after installing xubuntu 14.04

    - by h3bm
    I have a vaio laptop and it used to have installed windows 8 and Xubuntu 13.04 in dual boot, everything was working fine. I decided to update my version of xubuntu 14.04 LTS mainly because the support for 13.04 is finished and LTS version have 3 years of support. What I did was to format the partition where xubuntu 13.04 was installed and install 14.04 in that formated partition. When I restarted my computer willing to start using my new system I got the following message: error: symbol 'grub_term_highlight_color' not found and I was not able to enter any OS. I tried boot-repair from live USB more than two times and it did not fix the problem. I tried to enter to my computer using super GRUB2 disk, however it does not apperar to work with UEFI active (besides super grub2 disk says it can) I only get the message "no operating system found". If I boot super grub2 disk with UEFI disabled, super grub2 disk can not detect any OS,I also tried Rescatux distro, however, as of super grub2 disk, rescatux cannot enter when UEFI is active. I tried boot-repair with the option of "restore EFI backups", after that I was able to boot on windows, but no grub menu appeared. I ran boot-repair again with no improving results Here is the last Bootinfo report I got: http://paste.ubuntu.com/7609801/ Do you have any idea of what is happening? I really appreciate your help, Best regards,

    Read the article

  • How can i install ubuntu on my ntfs hdd without formatting?

    - by Ridvan Coban
    My hdd is just one partition in ntfs (500gb) and 430 gb is used by my photos/movies/music etc which i never will want to lose. Actually i installed ubuntu on a usb flash drive (using it right now) but it is too slow that way. But my problem is : My computer is damaged ( maybe chipset or but not sure) and none of the windows versions (xp,vista,7) works on my pc. I get blue screen error as soon as windows startup logo shows. But ubuntu just works flawless. That means i cannot use wubi. I wanted to shrink my hdd without losing data (which can be done in windows) but found nothing about that on ubuntu forums. Is this possible? Or install ubuntu on my ntfs filesystem? Note : I don't have chance to backup 400 gbs of data. Sorry for my question if it's written a bit compex. I hope you get the point and someone has an idea ;)

    Read the article

  • Windows 7 and Ubuntu Boot/Corruption Problems

    - by Kiraisuki
    I searched around, but I couldn't find the answer to why Windows 7 Ultimate 64x and Ubuntu 12.04 LTS 64x could'nt live together happily on my Asus G1s-X1 laptop. I had Windows 7 Ultimate 64x installed on the laptop when I bought it (bought it used, it comes with Vista new) and I wanted to try out Ubuntu and see what all the hype about the free OS was. I installed Ubuntu on an external 80GB iomega HDD with Windows 7 on my main drive. They both work fine for about 2-3 weeks, until Ubuntu suddenly is unable to boot. A few days after Ubuntu fails, Windows corrupts majorly (winload.exe, ntkrnlpa.exe, and various others corrupt randomly) and Windows Recovery Environment is completely useless. Booting to a live USB with Ubuntu and trying to reinstall it fails, and trying to wipe the main drive and install it there fails as well (something about my graphics card.) I managed to get Windows 7 Ultimate 64x back up and running (after many disk formats) but now I am left with a broken (and invisible) Ubuntu installation on the external drive. Is there any way to get the broken and non-bootable Ubuntu installation off the HDD without damaging or erasing the many files and programs installed and stored on the 80GB drive?

    Read the article

  • Dell Upgrade to 12.04 LTS No wifi, graphic card driver and bluetooth Problem?

    - by Mattlinux1
    (Dell inspiron m5040 Upgrade to 12.04 LTS from 11.10 wifi wont work and has two bluetooth icons?) Old title of post! No Wifi/Bluetooth Problem. "Both Fixed", see below comments for bluetooth fix and see bottom answer for wifi fix. My online upgrade of 12.04 LTS, was installed to my laptop the Dell inspiron m5040, when it was done i found that my wifi did not even get picked up anymore and i now have two bluetooth icons at the top?? So what i have been doing for now is at the boot screen. I hit the use previous linux version, this works fine but also has the two bluetooth at the top. Is very thankful for any answers for this fix, Thank You. Ok bluetooth problem solved by – fossfreedom answer by deleting the other bluetooth program running in software center. Now the other problem is Wifi: just have to restart system as it works in previous linux version boot opt, but on the first boot screen opt run ubuntu it will not pick up wifi drivers. Broadcom 802.11 Linux STA wireless driverfor use with Broadcom's BCM4311-, BCM4312-, BCM4313-, BCM4321-,BCM4322-, BCM43224-, and BCM43225-, BCM43227- and BCM43228-basedhardware. And 3D-accelerated proprietary graphics driver for ATI cards. This driver is required to fully utilise the 3D potential of some ATI graphics cards, as well as provide 2D acceleration of newer cards. will not instill is there anyway for me to make a copy of the drivers via usb HDD and then put them on new upgraded version.

    Read the article

  • crippling repeating "pciehp card not present" notifications

    - by Nanne
    When using ubuntu (12.04, both installed and on a live usb) I get a lot of these messages: pciehp 0000:00:1c.5:pcie04: Card not present on Slot(37) pciehp 0000:00:1c.5:pcie04: Card present on Slot(37) And with a lot I mean about 20 per second. This has a crippling effect, and I would like to get rid of it :) The computer is a packard bell easynote BG48-U-100 DC. I tip I picked up from some fedora/redhat error here was to look at lspci -vnn. I have pasted the part about "00:1c.5" here: http://pastebin.com/0sfsiqW2 For what good it may do, here is the lsmod of my machine: http://pastebin.com/DQZy1kAL From that first pastebin I think to conclude that it has to do with the module shpchp, which seems to me (aka: google) to have something to do with ACPI. That's as far as I've come in disecting this. Can anyone help me along further? What can I do, check etc? I did see this topic but my intentions are not to surpress the error message: I know how to do this (from that topic ;) ), but I'm looking for a real sollution. Finding the problem on the internet does suspect me to believe it is neither an ubuntu specific nor a packard-bell specific problem.If you google the problem it seems that is present on several other distribution/hardware combo's as well, and it looks like the advice is to remove one of the drivers? I have no clue as to which driver I should look at and and what would be the effect of just removing it. I have seen this topic which is old-ish, but describes my problem and is about a similar computer. The solution in this topic was to compile a new kernel using a spanish guide, which seems a bit extreme to me, so I'm kinda hoping for a better solution than that.

    Read the article

  • How do I debug an overheating problem?

    - by Tab
    Hello guys. I have a problem with my Laptop (Dell Inspiron 1564 Core i5 4GB Ram VGA ATI Mobility Radeon HD 4300 running Ubuntu 10.10 32bit). It shuts down abruptly without even a lag in the application I am working with before shutdown. I think it's overheating problem. Actually the laptop is hot all the time when I am running Ubuntu. When I switch back to windows, even with intense load it won't shutdown or show any problem as long as I keep proper ventilation (when the air openings are blocked it does the same). Actually on Ubuntu i don't usually do things that need much CPU power, usually surfing internet, coding web pages and sometimes playing with python and ruby. I am not enabling desktop effects so no GPU load except the normal GNOME gui. Now as I am writing the Processor load in the panel monitor applet is 0%, Memory 11% by programs, 22% by cache. And i have CPU Frequency monitor for each of the 4 cores set to 1.20 Ghz (the lowest possible value, i am not sure if this applet does really limit CPU usage). Running sensors in terminal gave me temp1: +26.8°C (crit = +100.0°C) temp2: +0.0°C (crit = +100.0°C) hddtemp /dev/sda at the terminal gave me /dev/sda: WDC WD3200BEVT-75ZCT2: 46°C All that fine but the laptop is Really hot i can feel it in the keyboard, mouse pad is painful to touch, and the fan is always spinning. I am also placing 2 small fans running on USB under the laptop right now and the laptop is lifted over the fans so it's well ventilated. When I am running windows it doesn't get that hot except when there is a really big load on the CPU and this is keeping me away from using Linux for everyday tasks. Actually I don't care much for speed as I can deal with low speed it's not going to shutdown abruptly. So please if you can help me and tell me what are the possible causes, where should I start ?

    Read the article

  • mount ext4 formated external drive->the drives green light won't stop flashing

    - by Gohlool
    I've installed kubuntu (after 10 years I am trying to play with linux) and manged to attach a external 1TB HDD drive over USB! The drive was formatted with NTFS and everything was working OK. I also changed the /etc/fstab here is my ntfs mount setting: /dev/sdb1 /media/samsung nts-3g auto,user,uid=1000,gid=1000,fmask=000,utf-8 0, 0 Now, I've reparationed the drive and formated it with ext4 filesystem! change my fstb like: /dev/sdb1 /media/samsung ext4 defaults,noatime 0, 0 now, when I plug my dive/or call sudo mount -a, my external drive's green light starts to flash and won't stop, but mount works .... What is the Problem? is this because of ext4? because with NTFS this won't happen! btw. after changing the owner of the /media/samsung and setting permissions 777, I can also access my drive like creating new folder atc. (although is's flashing constantly)! What is my mistake? btw. can you please let me know how to set the owner and the permissions for my /media/samsung directory in fstab for ext4 like I did it for NTFS? Thanks in advance

    Read the article

  • Passing data between the VirtualBox Host and the Guest

    - by Fat Bloke
    Here's a good question: "How can you figure out the VM name from within the VM itself?" While this data is not automatically available, the general purpose, and very powerful VirtualBox "GuestProperty" APIs can be used from the host and guest to pass arbitrary data, in key/value pairs format, in and out of the guest. Note that this does require that the VirtualBox Guest Additions have been installed in the guest. To play with this, try using the "VBoxManage" command line on your VirtualBox host machine, and "VBoxControl" in the guest. Host syntax VBoxManage guestproperty get <vmname>|<uuid> <property> [--verbose] VBoxManage guestproperty set <vmname>|<uuid> <property> [<value> [--flags <flags>]] VBoxManage guestproperty enumerate <vmname>|<uuid> [--patterns <patterns>] VBoxManage guestproperty wait <vmname>|<uuid> <patterns> [--timeout <msec>] [--fail-on-timeout]   Guest syntax VBoxControl.exe guestproperty        get <property> [-verbose] VBoxControl.exe guestproperty        set <property> [<value> [-flags <flags>]] VBoxControl.exe guestproperty        enumerate [-patterns <patterns>] VBoxControl.exe guestproperty        wait <patterns>                                      [-timestamp <last timestamp>]                                      [-timeout <timeout in ms>  So to solve our problem above, we set the vm name in the Host system on an arbitrary key like this: $ VBoxManage guestproperty set "Windows 7 (x64)" /MyData/VMname "Windows 7 (x64)" And within the guest we can use: C:\Program Files\Oracle\VirtualBox Guest Additions>VBoxControl.exe guestproperty get /MyData/VMname Oracle VM VirtualBox Guest Additions Command Line Management Interface Version 4.1.14 (C) 2008-2012 Oracle Corporation All rights reserved. Value: Windows 7 (x64) The GuestProperty API is pretty powerful, so for the interested, get more info in the User Manual. - FB 

    Read the article

  • How to Use a PIN Instead of a Password in Windows 8

    - by Taylor Gibb
    Entering your full password on a touch screen device can really become a pain in the neck, luckily for us we can link a short 4 digit PIN to our user account and log in with that instead. Note: PIN codes are nowhere near as safe as using an alphanumeric password, however, they do still have a purpose when you don’t want to enter your 15 character password on a touch screen device. Creating a PIN Press the Win + I keyboard combination to bring up the Settings Charm, then click on the Change PC settings link. This will open up the Modern UI PC Settings app, where you can click on the Users section. On the right hand side you will see a Create a PIN button, click on it. Now you will need to verify that you are the owner of this user account by entering your password. Then you can choose a PIN, remember that it can only contain digits. Now when you get to the login screen you will have the option to use a PIN. How To Boot Your Android Phone or Tablet Into Safe Mode HTG Explains: Does Your Android Phone Need an Antivirus? How To Use USB Drives With the Nexus 7 and Other Android Devices

    Read the article

  • Fast Data - Big Data's achilles heel

    - by thegreeneman
    At OOW 2013 in Mark Hurd and Thomas Kurian's keynote, they discussed Oracle's Fast Data software solution stack and discussed a number of customers deploying Oracle's Big Data / Fast Data solutions and in particular Oracle's NoSQL Database.  Since that time, there have been a large number of request seeking clarification on how the Fast Data software stack works together to deliver on the promise of real-time Big Data solutions.   Fast Data is a software solution stack that deals with one aspect of Big Data, high velocity.   The software in the Fast Data solution stack involves 3 key pieces and their integration:  Oracle Event Processing, Oracle Coherence, Oracle NoSQL Database.   All three of these technologies address a high throughput, low latency data management requirement.   Oracle Event Processing enables continuous query to filter the Big Data fire hose, enable intelligent chained events to real-time service invocation and augments the data stream to provide Big Data enrichment. Extended SQL syntax allows the definition of sliding windows of time to allow SQL statements to look for triggers on events like breach of weighted moving average on a real-time data stream.    Oracle Coherence is a distributed, grid caching solution which is used to provide very low latency access to cached data when the data is too big to fit into a single process, so it is spread around in a grid architecture to provide memory latency speed access.  It also has some special capabilities to deploy remote behavioral execution for "near data" processing.   The Oracle NoSQL Database is designed to ingest simple key-value data at a controlled throughput rate while providing data redundancy in a cluster to facilitate highly concurrent low latency reads.  For example, when large sensor networks are generating data that need to be captured while analysts are simultaneously extracting the data using range based queries for upstream analytics.  Another example might be storing cookies from user web sessions for ultra low latency user profile management, also leveraging that data using holistic MapReduce operations with your Hadoop cluster to do segmented site analysis.  Understand how NoSQL plays a critical role in Big Data capture and enrichment while simultaneously providing a low latency and scalable data management infrastructure thru clustered, always on, parallel processing in a shared nothing architecture. Learn how easily a NoSQL cluster can be deployed to provide essential services in industry specific Fast Data solutions. See these technologies work together in a demonstration highlighting the salient features of these Fast Data enabling technologies in a location based personalization service. The question then becomes how do these things work together to deliver an end to end Fast Data solution.  The answer is that while different applications will exhibit unique requirements that may drive the need for one or the other of these technologies, often when it comes to Big Data you may need to use them together.   You may have the need for the memory latencies of the Coherence cache, but just have too much data to cache, so you use a combination of Coherence and Oracle NoSQL to handle extreme speed cache overflow and retrieval.   Here is a great reference to how these two technologies are integrated and work together.  Coherence & Oracle NoSQL Database.   On the stream processing side, it is similar as with the Coherence case.  As your sliding windows get larger, holding all the data in the stream can become difficult and out of band data may need to be offloaded into persistent storage.  OEP needs an extreme speed database like Oracle NoSQL Database to help it continue to perform for the real time loop while dealing with persistent spill in the data stream.  Here is a great resource to learn more about how OEP and Oracle NoSQL Database are integrated and work together.  OEP & Oracle NoSQL Database.

    Read the article

  • "Unable to install GRUB in /dev/sda" when installing GRUB

    - by vicban3d
    I recently bought a shiny new Lenovo Yoga 2 Pro and I want to dual boot it with Ubuntu for studying purposes. Its built-in OS is Windows 8.1 and it has a 256GB SSD. I've made a separate 90GB partition just for Ubuntu and a live USB to install it. The first time everything seemed to work great, I solved the wifi issued by blacklisting ideapad_laptop, the installation went flawlessly and Ubuntu worked fine. When I got up the next morning and turned on my laptop it booted into Windows right away without ever showing the GRUB menu. So I tried to reset, and checked my partitions with the Disk Manager and everything looked fine. Since I couldn't find a solution online I went ahead and formatted the partition to try and install again. This time and every time since, the installation was aborted and I got a fatal error saying: Unable to install GRUB in /dev/sda Executing `grub-install /dev/sda` failed. This is a fatal error. Can anyone please suggest a solution to this problem? If any further information is needed I would be happy to provide it. Thanks. When installing I get the following in details: ubuntu kernel: [ 1946.372741] FAT-fs (sda2): error, fat_get_cluster: invalid cluster chain (i_pos 0). ubuntu grub-installer: error: Running 'grub-install --force failed.

    Read the article

  • recent unreliable wireless connection

    - by gabkdlly
    Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I have observed this problem with a Netgear KWGR614 Router ( with the manufacturers firmware ), as well as with a TP-LINK TL-WR741ND router running OpenWrt. Taking a look at my routers logs, I find many instances of the following line: Tuesday,04 Jan 2011 03:53:01 [TCP SYN Flood][Deny access policy matched, dropping packet] I know that the Netgear router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. I use WEP or WPA to encrypt the wireless network. Is it possible that someone is jamming my signal ?

    Read the article

  • TechEd North America 2012–Day 3 #msTechEd #teched

    - by Marco Russo (SQLBI)
    Yesterday I spent the longest day at this TechEd: we talked with many people at Community Night until 9pm and I have to say that just a few months after Analysis Services 2012 has been released, there are many people already using it. And the adoption of PowerPivot is starting to be quite large. Many new ideas and challenging coming from several different real world scenarios. I was tired but really happy. Alberto presented his Many-to-Many Relationships in BISM Tabular session that was in the same time slot of the BI Power Hour. For this reason, very few people attended Alberto’s session so I think many will watch the recorded session (it should be available within a few days). So what about today? I’ll spend some time at Technical Learning Center area (full schedule here) but the most important event today will be the Querying multi-billion rows with many to many relationships in SSAS Tabular (xVelocity) at the Private Cloud, Public Cloud and Data Platform Theater in the Technical Learning Center area (next to the SQL Server 2012 zone).  Why you should attend? Mainly because you will see live demo over 4 billion rows table with many-to-many relationships involved in complex queries. But for those of you that think this is not enough to attend a 15 minute funny session, well, we’ll give away some 8GB USB Memory Keys to those of you that will guess exact response time of queries before execution. Convinced? Join us at 11:15am and don’t be late, the session will finish at 11:30am! After that, we’ll run a book signing session at the Bookstore at 12:30pm and I will be in the Technical Learning Center area at 3:00pm until 5:00pm. See you there!

    Read the article

  • Ubuntu installed along side Win 8 but not shown in boot

    - by Mahesha999
    Actually the question says it all, but let me tell you what I did, so u may find exactly what might have went wrong: I have Win 8 installed on 500 GB HDD. SO I shrunk it four times for: partition 1 - the original partition containing Win 8 sys (118GB) partition 2 - NTFS formatted for my data (188GB) partition 3 - NTFS formatted for my data (100GB) partition 4 - NTFS formatted for Linux distro 1 (I reformatted it to ext4 during Ubuntu installation) (25GB) partition 5 - NTFS formatted for Linux distro 1 (21GB) So now I booted Ubuntu from USB (created from ubuntu-12.04-desktop-amd64.iso) and deleted last two partitions 4 and 5 to create: partition 1 - ext4 where I installed Ubuntu (25GB) partition 2 - Swap (4GB) partition 3 - unallocated space, not formatted yet (17GB) Ubuntu installation said it installed successfully and that I have to restart to boot in Ubuntu. But when I restart Windows 8 auto booted - there was no dual boot. After that I devided above 100GB partition to 80Gb and 20GB ones (since I read online that I should have /home in separate partition for convenience, so I created 20GB partition for it) So I went on to manually create boot entry using EasyBCD as below show in picture at below link http://s19.postimage.org/dof2zuvw3/Free_BCD.png When I created the entry, FreeBCD showed the information as follows: Windows Boot Manager -------------------- identifier {9dea862c-5cdd-4e70-acc1-f32b344d4795} device partition=\Device\HarddiskVolume2 description Windows Boot Manager locale en-US inherit {7ea2e1ac-2e61-4728-aaa3-896d9d0a9f0e} integrityservices Enable default {ea8167ad-d189-11e1-90e4-ab2f09569dcc} resumeobject {ea8167a3-d189-11e1-90e4-ab2f09569dcc} displayorder {ea8167ad-d189-11e1-90e4-ab2f09569dcc} {ea8167b1-d189-11e1-90e4-ab2f09569dcc} toolsdisplayorder {b2721d73-1db4-4c62-bf78-c548a880142d} timeout 10 displaybootmenu Yes Windows Boot Loader ------------------- identifier {ea8167ad-d189-11e1-90e4-ab2f09569dcc} device partition=C: path \Windows\system32\winload.exe description Windows 8 locale en-US osdevice partition=C: systemroot \Windows resumeobject {9bc7fdf7-3ae0-11e2-be77-806e6f6e6963} Real-mode Boot Sector --------------------- identifier {ea8167b1-d189-11e1-90e4-ab2f09569dcc} device partition=C: path \NST\AutoNeoGrub0.mbr description Ubuntu Notice the last bolded entry created. Howevever after thet, when I rebooted it firstly showed old DOS like bootloader (no Windows 8 UI based bootloader) with two entries Windows and Ubuntu. Windows 8 was booting correctly but I was getting an error while booting Ubuntu taking me to GRUB Rescue. Please help am new to Linux world.

    Read the article

  • Why can't tuxboot and ubuntu play well together?

    - by mmr
    I'm trying to get clonezilla to run off of a usb stick, and it seems that the right way to do that is via tuxboot. Tuxboot is not compilable on ubuntu. I used git to get it from the repository, and then when I run the 'install' script (because building it is apparently not allowed, since the build script just tries to install windows things). Qmake-linux wants my qmake executable to be in the same directory as the stuff I pulled down, and let's just say that if there's a way to do this easily, I ain't seein' it. So then I download the linux file, the most recent of which is tuxboot-linux-25. Try to run it, get a failure that libpng12.so.0 isn't found. OK, then I go to install that via the instructions I found on the web but firefox seems to have already deleted from my history (yay!) Then I add the /usr/local/lib directory to ldconfig via emacs (had to install that too, of course): http://ubuntuforums.org/showthread.php?t=369848 I still get the errors that libpng12.so.0 cannot be opened because 'No such file or directory'. ldconfig -p | grep libpng shows that the library is there, but it still doesn't seem to be findable. What to do next? (for the record, doing this in windows is painless-- download, click, and it's done. But I'm trying to be all linuxy and get away from Windows for this...)

    Read the article

< Previous Page | 538 539 540 541 542 543 544 545 546 547 548 549  | Next Page >