Search Results

Search found 18422 results on 737 pages for 'down town'.

Page 543/737 | < Previous Page | 539 540 541 542 543 544 545 546 547 548 549 550  | Next Page >

• Grayed-Out Sleep and Hibernate Options on Windows 7 After Updating Graphics Driver

  - by Maxim Zaslavsky

  I have a Gateway M275 Tablet PC, on which I've installed Windows 7 Ultimate. The laptop is quite old, so there aren't any Win7 drivers for it, not to mention any Vista drivers. Win7 has been working for some time, but I noticed that my video output wasn't working. I went into Device Manager and found that I didn't have a driver for my video card: it just recognized it as the standard one. I searched online and found an XP driver for it, released by Gateway. Device Manager accepted this driver and prompted me to reboot. After that, I noticed that my Sleep and Hibernate options in the Shut Down menu have been grayed-out. I looked online and found that many people are attributing this to display drivers, as such an old driver would surely not be compatible with the standby procedures Windows 7 uses. To make it clear: I was able to Sleep and Hibernate before updating the drivers; now, I can't. Running powercfg /a gives me, "An internal system component has disabled this standby state," for each available standby mode. Is there some way that the driver can be modified to support hibernation? The new driver fixed my video output problem, but I guess hibernation is more important for me. If not, what steps should I take to remove the driver and just leave the standard Windows one, which previously supported hibernation and sleep on this computer? Thanks in advance.

  Read the article

• How to detect/list rogue computers connected to a WIFI network without access to the Wifi Router interface? [migrated]

  - by JJarava

  This is what I believe to be an interesting challenge :) A relative (that leaves a bit too far to go there in person) is complaining that their WIFI/Internet network performance has gone down abysmally lately. She'd like to know if some of the neighbors are using her wifi network to access the internet but she's not too technically savvy. I know that the best way to prevent issues would be to change the Router password, but it's a bit of a PITA having to re-configure all wifi devices... and if the uninvited guest broke the password once, they can do it again... Her wifi router/internet connection is provided by the telco, and remotely managed so she can log-on to their telco account's page and remotely change the router's Wifi password, but doesn't have access to the router status page/config/etc unless she opts out of the telco's remote support and mainteinance service... So, how could she check if there are guests in the wifi with this restrictions and in the most "point and click way"? In this case I'd probably use nmap to look for other devices in the network, but I'm not sure if that's the easiest way to do it. I'm not a wifi expert, so I don't know if there are any wifi-scanning utils that can tell us who's talking to the router... Lastly, she's a Windows user as I guess that'll influence the choice of tools available Any suggestions more than welcome Regards!

  Read the article

• "Dictionary problem." Error with VMPlayer

  - by George Mauer

  I'm pretty new to using vmware virtualization (been a virtualbox user) so I'm hoping you guys can help me out. I recently got an external usb disk containing a vm for a client, downloaded vmplayer, set it up with "Open a Virtual Machine", ran it, easy as pie. After working with it a bit this morning, I shut the VM down and now trying to start it back up again I get this: I tried removing the vm from my library, now it happens whenever I try to add it back in. In the meantime, I can still access other virtual machines so it seems like the problem might be with the virtual disk. So two questions: This is obviously not a very helpful error message. Where can I go to get more information? My Application EventLog doesn't contain anything from VMWare. What steps can I take to fix the problem? Edit: A couple more pieces of information. I did not take any snapshots. I don't think VM Player even has that ability. I have a zip file of (what I assume) is the state of the VM when it was sent to me. I cannot unzip it as it is huge and simply requires more HD space than I have available but I did extract the vmx file and examine it. Other than the UUIDs and the fact that mine reads cleanShutdown = "FALSE" they are identical. The log contains the following lines Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead: Unable to load dict from 'E:....\MachineName.vmsd'. Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead failed for file 'E:....\MachineName.vmx': Dictionary problem (6) Jun 23 10:11:18.082: vmx| SNAPSHOT: Snapshot_TimeStampTiers failed: Dictionary problem (6)

  Read the article

• Is there a monitoring software suite that will alert me if it has received no activity in a time period?

  - by matt b

  This might be a very basic question, but I am not very familiar with the exact features of Nagios versus Munin versus other monitoring tools. Let's say we have a process that needs to run daily for some very important infrastructure reasons. We've had cases where the process did not run or was otherwise down for a number of days before anyone noticed. I'd like to set up a system that will enable me to easily know when the daily run did not take place for some reason. I can set up this process to send an email on every successful run (or every failed run), but I do not trust that the people receiving this email would notice an absence of an "I'm OK" message. What I am envisioning is some type of "tripwire" service which this V.I.P. (very-important-process) can send a status message to each time it runs, whether successfully or not; and if the "tripwire" service has not received any word from the VIP within a configurable amount of time, it can then send an alert to someone. (The difference between what I envision and the first approach I outlined is a service that sends a message only in abnormal conditions, rather than a service that sends messages each day that the status is normal/OK). Can Nagios be set up to send an alert like this, if it has not heard from a certain service/device/process in N days? Is there another tool out there which does have this feature?

  Read the article

• No audio with streaming video

  - by Chris Barnhill

  I am having trouble with audio when playing streaming videos. My sound card is fine. I know this because if I play sounds from my local machine, there's no problem. It's only when I try to play sounds from the internet that I lose audio. This only started happening recently when I did 2 things: I connected a USB headphone/microphone set to record screencasts I began recording/publishing screencasts from screenr.com. I have tried playing video both with the headset connected and without it connected: it makes no difference. If I record a screencast on screenr.com and preview it, I hear the audio. But once I publish is and play it, there is no audio. I also hear no audio with YouTube videos. I really hope someone can help. Thanks. The latest is that the problem went away after I powered my system off and on. A reboot didn't do it, I had to actually shut down the power.

  Read the article

• Ruby installed on Ubuntu 10.10 slow on one machine but not other

  - by Aaron Jensen

  I have a machine that was provisioned several months ago. RVM was used to install ruby 1.9.3-p125 as well as 1.9.3-p125-perf. When I compared raw ruby performance to another identical machine the older machine smoked them. For example: ================================================================================ With in-block needle calculation ================================================================================ Rehearsal ---------------------------------------------- detect 3.790000 0.000000 3.790000 ( 3.800895) each 2.410000 0.000000 2.410000 ( 2.420860) any 3.960000 0.000000 3.960000 ( 3.972099) include 1.440000 0.000000 1.440000 ( 1.442862) ------------------------------------ total: 11.600000sec vs ================================================================================ With in-block needle calculation ================================================================================ Rehearsal ---------------------------------------------- detect 10.740000 0.000000 10.740000 ( 10.769366) each 6.080000 0.010000 6.090000 ( 6.106323) any 10.600000 0.000000 10.600000 ( 10.641606) include 4.160000 0.000000 4.160000 ( 4.171530) ------------------------------------ total: 31.590000sec I attempted to reinstall 1.9.3-p125 with rvm on the fast machine and that ruby is now slow. It's as if something changed in RVM, or I installed some package that made compiled versions of ruby perform significantly worse. I know this is a tough question to answer, but what things should I look into in order to track down why the performance has suffered so much? edit I just attempted to install with ruby-build and the version installed was fast. Something rvm is doing to build it in my environment is slow.

  Read the article

• Apache Server with memcache, varnish and php slow request times

  - by coolestdude1

  My issue is that these servers are taking rather long for request about 2 seconds on average just to serve files. When we had just one server doing everything it was noticeably faster even with the same web app (Drupal 6 and Drupal 7). I want to get this number down to a reasonable level and so I need some help getting to the bottom of why the request times are so slow. This can cause the webapp to hang on post or put and generally leads to a bad user experience on my sites. PS: I am more of a server newbie so this has confounded me for quite some time. The domains: collabornation.net nptrainingworks.com (they run off the same two webservers using vhost configs) The Gear: Two Rackspace 4 Gig servers running CentOS 6.2 Final They have a mounted file system (gluster) that is used to keep files the same on both machines. They are behind a rackspace load balancer running round robin. Mysql is run using php-pdo and php-mysql as such mysql is run on another instance running memcache on that machine with phpMyAdmin located there as well. Apache version number 2.2.15-15.el6.centos.1 (httpd.x86_64) Varnish version number 3.0.2-1.el5 (varnish.x86_64) PHP version number 5.3.14-1.el6.remi (php.x86_64) Configs Linked Below Apache Conf Vhost Conf Varnish Backends Varnish Defaults Varnish Acl PHP INI Again need some help, much appreciated!

  Read the article

• Locked out of our Comcast Business Gateway for seemingly no reason

  - by Tyler

  A little backstory... Last fall we migrated our ISP from AT&T to Comcast at one of our offices. At that time, we received a new modem/router from Comcast and we configured everything to our liking. We've never really had very many issues with the router aside from having to restart it every once in a while. Here's the problem... About three months ago I changed the password on the router from the default. After that, I logged into the router several times to make changes with no issue. During May I logged into the router to add two new static routes, no problems. A week ago, I tried to log into the router and could not. I tried the non-default password that I changed it to, the default, anything and everything I could think of and no luck. I restarted the router on Monday thinking it may just be locked up, but after the restart it would still not let me log in. This router is at our other office about 2 hours from here and I want to avoid having to drive down there and reset to factory defaults, reconfigure, etc. Any ideas?

  Read the article

• Cache Control Headers with IIS 7.5

  - by Brad

  I'm trying to wrap my head around client side (web browser) caching and how it works in relation to IIS 7.5 cache control headers. In particular: If we want to force clients to reload cached resources, how must IIS be configured? Do we need to set expire web content immediately if the resources on the server have a more recent Modified Date (or ETag value)? Right now we're not setting any cache headers. So if I set a cache header of no-cache (which I think is the equivalent of expire web content immediately) will that force the web browser to obtain a new version of a particular file. Or will the browser only request a new version after it deems its current copy to be stale and then from that point forward not cache it? Would a best practice be to set a cache control flag of 1 week, then 8 days before I know I am going to make a change set the cache control down to for instance 30 minutes? But if I do that and then need to immediately expire an item from users caches because there was an issue with it how do I do that?

  Read the article

• Does Guest WiFi on an Access Point make any sense? [migrated]

  - by Jason

  I have a Belkin WiFi Router which offers a feature of a secondary Guest Access WiFi network. Of course, the idea is that the Guest network doesn't have access to the computers/devices on the main network. I also have a Comcast-issues Cable Modem/Router device with mutliple wired ports, but no WiFi-capabilities. I prefer to only run one router/DHCP/NAT instead of both the Comcast Router and the Belkin Router, so I can disable the Routing functions of the Belkin and allow the Comcast Router to But if I disable the Routing functions of the Belkin device, the Guest WiFi network is still available. Is this configuration just as secure as when the Belkin acts as a Router? I guess the question comes down to this: Do Guest WiFi's provide security by 1) only allowing requests to IPs found in-front of the device, or do they work by 2) disallowing requests to IPs on the same subnet? 1) Would mean that Guest WiFi on an access point provides no benefit 2) Would mean that the Guest WiFi functionality can work even if the device is just an access point. Or maybe something else entirely?

  Read the article

• Proper approach to debug PC startup problems (POST)

  - by saurabhj

  My CPU was heating up to around 65 deg C and last time this had happened (about a year ago), I got thermal paste put between the CPU and heat sink and this managed to get it down to about 45 - 50 degrees. This time, I got some thermal paste and put it myself. However, my PC is not showing the POST display and not starting up. This is what happens LEDs light up HDDs spin Mouse is getting power All fans including the processor fan starts No display on monitor No diagnostic beep sounds (no sounds at all) What I have tried Removing everything including RAM, HDD, PCI cards, AGP card Boot up machine No changes from first state. What steps can I take to figure out where the problem lies? Note (might be important) When I removed the heat sink, the processor came out with it (it was stuck to it inspite of the processor latch on) Had to pry it separate with a screw-driver. Configuration Pentium 4, 2.8 Ghz with HT (very old, I know) Original Intel Mobo with onboard sound and graphics (GB series) 2x512 Mb DDR-RAM 2 SATA disks (320 Gigs / 250 gigs) DVD Writer Creative Sound Card Network card Any help would be appreciated. Thanks!

  Read the article

• System x3550 M2 stuck on system initializing after firmware upgrades

  - by itmanager223

  Hey guys so i have been having this major issue for the last few hours now. I have a system x 3550M2 server and i ran the UEFI and IMM firmware upgrades within windows server 2008 R2 x64. All upgrades went fine and i was told to reboot. I performed the reboot cleanly using the OS restart option. Upon restarting it showed the system initializing screen and it stayed there for a good hour. After that hour i figured it froze and so i powered down and power up again. Now i can not boot back up to even see the IBM splash screen or the OS... I have tried switching the Jumpers to go to the backup UEFI and backup IMM and no luck. I have also reset the CMOS power and i have pressed the reset button 3 times on the light path and no luck. There are no lights light on the light path to indicate anything is broken. The only thing i see on the light path is the number 0.5. Any ideas guys i am quite stumped with this problem. Thanks a lot, Dani Cela

  Read the article

• How to verify TRIM/discard on encrypted swap?

  - by svarni

  I am using an encrypted swap partition via ecryptfs-setup-swap on my Ubuntu 13.04 computer using a SSD. I have manually set up trim for my ext4 root partition (simply by adding the "discard" option in /etc/fstab). I also manually ran fstrim on the root partition prior to booting and using dstat I saw that for a few seconds several GB/s of data have been written to the disk. That was presumably the effect of the trim command. These high writerates are reproducable by deleting huge files and have not occured before setting up trim, so I take them as evidence for working trim/discard. Manually enabling trim on my root partition has stopped the wearout of my precious new disk from 365 used reserved blocks (out of 6176 total) within three months down to 0 additional used reserved blocks within three additional months (data from SMART attributes). Because I want to minimize the wearout of my SSD I now would like to know whether my swap partition (which is encrypted using ecryptfs-setup-swap) also makes use of the trim/discard option. I tried sudo swapon -d -v /dev/mapper/cryptswap1 but did not receive particular information ("-v") about whether trim/discard ("-d") was applied. If unsupported, i would expect a message. Then I tried sudo dd if=/dev/sda6 count=1 BS=1M | xxd | less directly after booting and when no swapspace was used but I saw not only zeroes. I assume, when looking at freshly trimmed regions, the disk would send zeroes instead of reading random sectors (and according to some forums, (unencrypted) swap space is trimmed once upon boot). Long story short: Are there any ideas on how to test if trim is effectively used for my encrypted swap? And if not, any ideas on how to - at least manually, for once - trim the whole swap space? I wouldn't want to tinker with the partition itself, because I dont know if it needs to be reinitialized as (encrypted) swap - I dont want to be left with an unbootable system :)

  Read the article

• VMware Workstation Bridged Network Host UnReachable

  - by user2097818

  VMware Workstation 7 on Win7-64 (Home Premium). I have confirmed this on any guest running on this machine (from winxp to debian). I am using a bridged network connection for my guests (Automatic on VMnet0). All of the network configuration is done with DHCP (including on the host). Problem What I can not do: Ping my host machine from inside any VM. (either shows me "Destination Host Unreachable" or will just timeout) What I CAN do right after power up, with no problems at all. I can connect to the internet from inside the VM I can ping my router from inside the VM I can ping other machines on my network from inside the VM Other machines can ping the VM Other machines can ping the host My host machine can ping the VM (this one is important. read further) Details So I have my router assigned as 192.168.2.1/255.255.255.0, and the router provides the DHCP service (and it seems to be doing so successfully). There are no IP conflicts on the network that I am aware of. All Gateways and Subnet masks are appropriate and matching. My entire workshop is on one single subnet, with one single DHCP server and gateway. There is one method in which I can ping successfully, but it requires an active connection initiated from the host (I start pinging from host to VM). During the period of the active connection, I can successfully ping from VM to host, using explicit IP address. As soon as the host connection is closed, the VM ping starts hanging with the same old messages. My Thoughts This really feels like a firewall problem, but I have turned off all firewalls on host and VM, powered down the network, powered back up, and the problem still persists. And if it was firewall, why would only the IP address associated with bridged VM networks be blocked. I feel as though my host operating system (Win7) is somehow configured incorrectly, or, VMware Workstation is configured incorrectly from the host side. Although I have done my best to put everything in default, I feel like I am missing something silly.

  Read the article

• Broken Vista. Can't open Windows settings.

  - by serena

  My neighbor has a Lenovo laptop with Windows Vista Home Basic. She's a noob and just uses the laptop for internet purposes. She said she had to close down Windows improperly (sometime ago, maybe 6 months) because of system freeze. She realized there's something wrong with her Windows when she tried to open Windows update settings. I took a look at the system and determined the following errors: When I click on Windows Updates, a bare white window opens for a sec. and closes immediately. When I try to open Computer Properties, the same thing happens. (Windows+Break doesn't work either.) When I try to open Bluetooth settings, the same thing happens. So Vista won't let me open any Windows settings, but installed programs work correctly (games, applications etc.). She has no Windows Vista discs since the laptop came with preinstalled genuine Vista. She also has no recovery discs. I don't think there is a system restore point for the time the system was stable. Now what can we do to solve this big problem?

  Read the article

• Have to run auto-negotiate between clients and switch - "old" switch works fine - "new" switch results in "port flapping"?

  - by ConfusedAboutSwitching

  I need some help understanding a problem we're having at work: We run Altiris/Deployment Solution and have to use auto-negotiate between client systems and our switches (Altiris apparently requires this for imaging, PXE boot and other functions). We have several areas with old wiring (Cat 3 & Cat 5) that have old 10/100 Cisco switches in them - and we can set these systems up to "auto/auto" (auto-negotiate on both the NIC and the switch port), and everything has been working fine. But - our networking crew changed out a couple of old switches for 10/100/1000 Cisco switches, and now - they are claiming that "auto/auto" won't work because the switches can't auto-negotiate the way the old 10/100 switches did - and that if we try to set the new gig switches to auto-negotiate, the switch port starts "port flapping", and shuts the port down. But - if we put the old switch back in - they work using "auto/auto" just fine - no port flapping. The networking crew is telling me that the problem is that we're putting "new switches" on "old wire", and that the old cabling can't/won't support the auto-negotiation with these new switches....??? There's something about this that doesn't make sense to me - can someone explain this to me? Or is our networking crew just doing something wrong in the configuration of these new switches? While will the old switches work "auto/auto", but the new switches won't?? HELP!!....and Thanks!! M

  Read the article

• Nginx proxy upstream cached?

  - by Julian H. Lam

  Attempting to resolve an issue that's been annoying me for a bit. I've distilled the symptoms into a set of reproducible steps: I have two sites, siteA, and siteB. They are both Node.js applications running on different ports (for the sake of example, 4567 and 4568) Both applications have their own file in sites_available (plus a symlink from sites_enabled), which contain the directives proxy_pass http://node_siteA/ and proxy_pass http://node_siteB/ respectively, inside of a location block. They also each have an upstream block (defined globally?): upstream node_siteA { upstream node_siteB { server 127.0.0.1:4567; server 127.0.0.1:4568; } } Site A and Site B have nothing to do with each other. Yes, I am restarting (reloading, actually) nginx every time I make a change. If I take down site B and attempt to access it via the web, I am served site A. Why is this? Thoughts Other times, when I create a new Site C, for example, nginx refuses to show me anything except "Welcome to nginx!" for ~5 minutes. This suggests a resolver timeout, perhaps? When I access Site B after its config has been deleted, and it sends me to Site A, this sounds like nginx sending me to servers in a round-robin fashion...

  Read the article

• standard deviation on excel

  - by user270692

  so I have 3 data sets, which all came from the first data set using the excel program. all consisted of random numbers from =randbetween(0,100) starting from A2:A102 which is 100 integers. for data set b I had to enter=SUM(A2+5) press enter and drag it down to get the integers for cells B2:B102 and for C I had to do multiplication t get it. I did =PRODUCT(A2:A102*5). so everything was taken from data set A. now I did the formulas needed to do sample standard dev and mean(average) . for data set a and b the standard deviations were the same but the mean was larger in data set B of course because I added 5 to each cell in set A. my question is why wouldn't the standard deviation be the same for data set C also? if im using the info from data set A? and how do I calculate the standard deviation (sample) by hand so I can explain why the standard dev doesn't change but the mean does. I don't know what numbers to include in the formula for sample standard deviation.

  Read the article

• How to kill ostensibly immortal process?

  - by DeeDee

  I had some huge file transfers operating on an NFS mount. The server on which the mount point resided was carelessly rebooted, and now the server from which these large transfers were initiated seems to be bogged down by them. If I run top, I see the following: The first thing I tried was to run kill with each the -1 -2 -9 and -15 flags, and each of the process ids shown above in turn. This allowed me to proceed, but didn't kill the processes. The next thing I attempted was to reboot the server, but neither reboot nor shutdown -r now worked. When I ran shutdown -r now the standard broadcast message was sent out, but the sever did not reboot. I confirmed this by looking at the server uptime, which was 25 days. So now I'm a little stuck. I'm running these commands as root. EDIT: Here's another interesting tidbit: In top, I don't see that any other processes are using more than a fraction of a percent of memory or more than 5% of CPU. EDIT 2: output of /var/log/messages

  Read the article

• What to do about old MacBook

  - by John

  I have a White MacBook version 10.5.8. I accidentally dropped it and about an inch of the most right side of the screen is blacked out. I can't see the clock and Trash Can because of this. I checked how much it would cost to repair, and the cost of repairing is a flat rate of $300. I thought that was kind of expensive, like a third of the cost of the MacBook itself. accidentally dropping a notebook is something that would happen sooner or later, so I think getting a Lenovo is the best. I ended up getting a MacBook pro 15 inch, but do you think it's worth the money to fix my old MacBook? I even saw some used MacBooks available on Ebay for about $400. Anyways I don't know what to do with it. I do like its screen and keyboard better than the MacBook Pro ones, because the screen is less glare-y and the keyboard is more crisp and fun to type on, and its more wieldy when I'm using it while lying down.

  Read the article

• Can't install Hyper-V in Windows 8 Pro. Causes boot loop, pain & suffering

  - by Nick

  Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated.

  Read the article

• iptables, blocking large numbers of IP Addresses

  - by Twirrim

  I'm looking to block IP addresses in a relatively automated fashion if they look to be 'screen scraping' content from websites that we host. In the past this was achieved by some ingenious perl scripts and OpenBSD's pf. pf is great in that you can provide it nice tables of IP addresses and it will efficiently handle blocking based on them. However for various reasons (before my time) they made the decision to switch to CentOS. iptables doesn't natively provide the ability to block large numbers of addresses (I'm told it wasn't unusual to be blocking 5000+), and I'm a bit cautious over adding that many rules into an iptable. ipt_recent would be awesome for doing this, plus it provides a lot of flexibility for just severely slowing down access, but there is a bug in the CentOS kernel that is stopping me from using it (reported, but awaiting fix). Using ipset would entail compiling a more up-to-date version of iptables than comes with CentOS which whilst I'm perfectly capable of doing it, I'd rather not do from a patching, security and consistency perspective. Other than those two it looks like nfblock is a reasonable alternative. Is anyone aware of other ways of achieving this? Are my concerns about several thousand IP addresses in iptables as individual rules unfounded?

  Read the article

• Nginx: Loopback connection via PHP's getimage size crashes server (Magento's CMS)

  - by Alex

  We were able to trace down a problem that is crashing our NGINX server running Magento until the following point: Background info: Magento Backend has a CMS function with a WYSIWYG editor. This editor loads some pictures via a controller in magento (cms/directive). When we set the NGINX error_log level to info, we get the following lines (line break inserted for better readability): 2012/10/22 18:05:40 [info] 14105#0: *1 client closed prematurely connection, so upstream connection is closed too while sending request to upstream, client: XXXXXXXXX, server: test.local, request: "GET index.php/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL,,/ HTTP/1.1", upstream: "fastcgi://127.0.0.1:9024", host: "test.local" When checking the code in the debugger, the following call does never return (in ´Varien_Image_Adapter_Abstract::getMimeType()` # $this->_fileName is http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif` # $_SERVER['REQUEST_URI'] = http://test.local/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL list($this->_imageSrcWidth, $this->_imageSrcHeight, $this->_fileType, ) = getimagesize($this->_fileName); The filename requests is an URL to the same server which is requesting the script a link to a static .gif that is not existing. Sample URL: http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif When the above line executed, any subsequent request to the NGNIX server does not respond any more. After waiting for around 10 minutes, the NGINX server starts answering requests again. I tried to reproduce the error with a simple test script that only calls getimagesize() with the given URL - but this not crash. It simple leads to an exception saying that the URL could not be loaded (which is fine as the URL is wrong)

  Read the article

• Excel equivilant of java's String.contains(String otherString)

  - by corsiKa

  I have a cell that has a fairly archaic String. (It's the mana cost of a Magic: the Gathering spell.) Examples are 3g, 2gg, 3ur, and bg. There are 5 possible letters (g w u b r). I have 5 columns and would like to count at the bottom how many of each it contains. So my spreadsheet might look like this A B C D E F G +-------------------------------------------- 1|Name Cost G W U B R 2|Centaur Healer 1gw 1 1 0 0 0 3|Sunspire Griffin 1ww 0 1 0 0 0 // just 1, even though 1ww 4|Rakdos Shred-Freak {br}{br} 0 0 0 1 1 Basically, I want something that looks like =if(contains($A2,C$1),1,0) and I can drag it across all 5 columns and down all 270 some cards. (Those are actual data, by the way. It's not mocked :-) .) In Java I would do this: String[] colors = { "B", "G", "R", "W", "U" }; for(String color : colors) { System.out.print(cost.toUpperCase().contains(color) ? 1 : 0); System.out.print("\t"); } Is there something like this in using Excel 2010. I tried using find() and search() and they work great if the color exists. But if the color doesn't exist, it returns #value - so I get 1 1 #value #value #value instead of 1 1 0 0 0 for, example, Centaur Healer (row 2). The formula used was if(find($A2,C$1) > 0, 1, 0).

  Read the article

• Multiple copies off the same printer on Windows 7 from PrintUIEntry

  - by Kev

  I currently have a number of bat files which work perfectly fine on Windows XP which install the same printer multiple times with a number of finisher options set - e.g. after running the bat file below I would end up with four printers in the printer drop down called Sharp Kits Printer - A4 Single Sided Sharp Kits Printer - A4 Single Sided Stapled Sharp Kits Printer - A4 Duplex Stapled Sharp Kits Printer - A4 Duplex which all have there options configured in the relevant way. I have amended on Windows 7 to point to correct INF file and printer name in the INF files - a single printer installs fine. However when I run the complete batch file only the first printer in it is installed - occassionally the later ones flash up in the GUI but then vanish when you press F5 and are still missing after a reboot. SET QUEUENAME=http://192.168.7.123:631/printers/Sharp700 SET PPD=J:\DRIVERS\Printers\MX700-Win7-64\SJ1JWENG.INF SET PPDENTRYNAME=SHARP MX-M700U PPD J: cd "\DRIVERS\Printers\MX700-Win7-64" SET NICENAME="Sharp Kits Printer - A4 Single Sided" SET PREFS="J:\SCRIPTS\Printers-Win7-64bit\Sharp_SINGLE_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... SET NICENAME="Sharp Kits Printer - A4 Duplex" SET PREFS="J:\SCRIPTS\Printers\Sharp_DUPLEX_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... I have tried adding the "/u" paramater to the end, I have changed the "/n" paramater to be different (e.g. n1, n2,n3 etc) - both of these result in the same. I have also tried to change the port (/r) to have "_1" (etc) on the end like the GUI would but this errors as the port doesn't exist. Is it possible to do this on Windows 7, and if so how?

  Read the article

< Previous Page | 539 540 541 542 543 544 545 546 547 548 549 550  | Next Page >