Search Results

Search found 17976 results on 720 pages for 'old versions'.

Page 543/720 | < Previous Page | 539 540 541 542 543 544 545 546 547 548 549 550  | Next Page >

  • Booting Debian5 (Lenny) on 2.6.16 Kernel

    - by bk
    Due to a proprietary kernel module that I don't have the source to and is very picky about what kernel versions it will load into (even with modprobe --f), I find myself in need of running a 2.6.16.XX kernel on my Debian5 machine. The machine boots fine with the 2.6.26-2 stock kernel, and I have successfully build and booted 2.6.26 and 2.6.31 based kernels by making a .deb and the ndoing dpkg -i. However, when I do the same approach for 2.6.16, the kernel hangs at boot. I'm testing this in a VMWare image, so I don't think its an issue of newer hardware not supported by the older kernel. For a working kernel, at boot I get: Uncompressing Linux.. OK booting the kernel Loading, please wait... mdadm: No devices listed in the conf file were found kinit name_to_dev_t /dev/hda5 (dev5,3) ... With 2.6.16.60, I never get the kinit message. It hangs after the mdadm line. There are no mdadm arrays on this machine, so I doubt its an issue inside the mdadm stuff, which is supposed to just error out as it does in the 2.6.26 case above, but for some reason I'm getting stuck getting into kinit. I've been banging my head against this wall so I'm very open to suggestions on how to go about troubleshooting this.

    Read the article

  • Using UDF on a USB flash drive

    - by CesarB
    After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

    Read the article

  • JVM system time runs faster than HP UNIX OS system time

    - by winston
    Hello I have the following output from a simple debug jsp: Weblogic Startup Since: Friday, October 19, 2012, 08:36:12 AM Database Current Time: Wednesday, December 12, 2012, 11:43:44 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:45:38 AM Line 1 was a recorded variable during WebLogic webapp startup. Line 2 was output from database query select sysdate from dual; Line 3 was output from java code new Date() I have checked from shell date command that line 2 output conforms with OS time. The output of line 3 was mysterious. I don't know how it comes from Java VM. On another machine with same setting, the same jsp output like this: Weblogic Startup Since: Tuesday, December 11, 2012, 02:29:06 PM Database Current Time: Wednesday, December 12, 2012, 11:51:48 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:51:50 AM Another machine: Weblogic Startup Since: Monday, December 10, 2012, 05:00:34 PM Database Current Time: Wednesday, December 12, 2012, 11:52:03 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:52:07 AM Findings: the pattern shows that the longer Weblogic startup, the larger the discrepancy of OS time with JVM time. Anybody could help on HP JVM? On HP UNIX, NTP was done daily. Anyway here comes the server versions: HP-UX machinex B.11.31 U ia64 2426956366 unlimited-user license java version "1.6.0.04" Java(TM) SE Runtime Environment (build 1.6.0.04-jinteg_28_apr_2009_04_46-b00) Java HotSpot(TM) Server VM (build 11.3-b02-jre1.6.0.04-rc2, mixed mode) WebLogic Server Version: 10.3.2.0 Java properties java.runtime.name=Java(TM) SE Runtime Environment java.runtime.version=1.6.0.04-jinteg_28_apr_2009_04_46-b00 java.vendor=Hewlett-Packard Co. java.vendor.url=http\://www.hp.com/go/Java java.version=1.6.0.04 java.vm.name=Java HotSpot(TM) 64-Bit Server VM java.vm.info=mixed mode java.vm.specification.vendor=Sun Microsystems Inc. java.vm.vendor="Hewlett-Packard Company" sun.arch.data.model=64 sun.cpu.endian=big sun.cpu.isalist=ia64r0 sun.io.unicode.encoding=UnicodeBig sun.java.launcher=SUN_STANDARD sun.jnu.encoding=8859_1 sun.management.compiler=HotSpot 64-Bit Server Compiler sun.os.patch.level=unknown os.name=HP-UX os.version=B.11.31

    Read the article

  • Apple Mac OS X Mavericks inside Virtual Box

    - by John Sonderson
    I have a few questions regarding Mac OS X and OS virtualization. A. Given all the legal restrictions imposed by Apple on Apple products, I would like to know whether it is legal to install the new and freely downloadable Apple Mac OS X Mavericks inside Oracle Virtual Box. B. What about older OS X versions such as Mountain Lion? C. How many machines can I install it on. What if I don't use the Mac to which the OS is downloaded but only use it on Virtual Box, and prefer to, say, install Linux on the Mac computer so that it doesn't become unusable due to the single user license policy and me running the OS on Windows 7 within Virtual Box? D. I have a PC running Windows 7 but would like to get the OS off a second had Mac I'm planning to purchase for this purpose. How must we proceed to copy the OS to an ISO so that I can install it on Windows 7? I am unfamiliar with Macs and do not know what software to use for the purpose, nor where the OS is downloaded to (as an ISO, .app executable, .gz or .zip file or whatever). If anyone could provide some guidance with the process I would sincerely appreciate it. Thanks.

    Read the article

  • Enable CPU fan always on

    - by Gundars Meness
    I am using 3 years old overheating laptop and I want my CPU fan to be spinning 24/7 regardless of the consequences. How to make it spin? The problem is that CPU & GPU heats up to 68°C (154 F) right after boot and never goes down, because CPU fan is not spinning full throttle. It starts spinning faster when temperature goes over 70°C and stops when it reaches seventy again. When doing heavy work on databases, it gets from 70 to 90 in no-time and automatically powers off. Bios does not contain any "fan spin 100%" options, just "spin slowly all the time" and "auto" which is more useless than the first one since my fan doesn't have pwm wire. Currently I'm solving this with cooling stand (3x5V), but it isn't much of a help. I would rather use the CPU fan since it is the only fan directly responsible for cooling down CPU/GPU. But how to make it spin 100% all the time? Should I attach it's red power wire to motherboard to get constant 5V (is there such option?), or is there an option to control it via software? Laptop: Samsung R528 2.3 GHz Intel i3 with Nvidia GeForce 310M Bios: Phoenix 03KT.M003.20100622.KSJ (and that is latest update) OS: Ubuntu 12.04.2 LTS with 3.2.0.51 kernel CPU fan: Image/Description Has 5V 0,4A and only 3 pins, no pwm. P.S. Yes, I did clean everything with alcohol, freed the air vents, changed thermal paste etc; that reduced temperature by 4 degrees.

    Read the article

  • Is there a way to avoid Wacom Control Panel to stop showing in certain cases ?

    - by S.gfx
    This is the problem: Suddenly, you double click on desktop wacom tablet settings icon, and it wont show the dialog. It appears to be loaded as it's shown down in the windows taskbar. I suspect is caused by change of resolution or some setting, maybe suddenly it sets the origin of the panel dialog at some 3000 thosand pixels to the right or something. I have digged that wacom_tablet.dat file to see if I fix it changing some value there, but looks like a log, a history, more than a ini for settings... And anyway does not solve it. My solution is having always a very complete settings file done and backed up to restore (with wacom utility for this, which in previous driver versions did not exist) when this happens, but is counter productive: You change the settings even per each project(and software) needs. I have seen it happenning with Cintiq 12", intuos4 A6, Graphires, Intuos 1. Is just me, doing something weird every time? I doubt it, is normal use, I am amazed that seems no one else had this prob(or nobody asked), happens often with typical use. Maybe is because am setting a shortcut in the desktop? Weird as it works perfect till some random moment... (Have digged Wacom's forums and FAQs, then here, but nothing related to it... Neither in "related questions".) The thing happens in Win XP, 7, etc. Done so during years in my experience, and several times at work, which is worse.

    Read the article

  • Linux DHCPD Mac-Address based Groups

    - by GruffTech
    Our Current DHCPD.conf looks like the following. subnet 10.0.32.0 netmask 255.255.255.0 { range 10.0.32.100 10.0.32.254; option subnet-mask 255.255.255.0; option broadcast-address 10.0.32.255; option domain-name-servers 208.67.222.222,208.67.220.220; option routers 10.0.32.5; host Dev-ABaird-W { hardware ethernet 00:1D:09:3E:49:13; fixed-address 10.0.32.94; } ... more static hosts .... } About as basic as it gets. The old router is 10.0.32.1, our company wanted to implement a squid proxy to better monitor web traffic while at work, and if necessary block large time-wasters, IE Facebook.com. However, we've quickly realized that this change has played a mean prank on our Polycom SIP Phones. Occasionally our phones will not ring, the end recipient hears ringing (this is artificially created by our PBX) however the handset never rings. The ONLY thing that has changed in our network is the option routers line. So, Since all Polycom MAC addresses begin with 00:04:F2 would it be possible in DHCP to say any 00:04:F2:::* MAC addresses get option routers 10.0.32.1, and anything else must talk with our Gateway?

    Read the article

  • How to run the CPU at something like 75%?

    - by Tobias Kienzler
    My notebook is too old for me to invest into a new fan (it will simply be replaced by a new one when the final heat death occurs), but when it runs on full speed I feel like sitting in front of a vacuum cleaner with integrated cooking... I'm currently using NHC, the Max Battery mode of which let's the CPU run at 50% (~800 MHz). That's fine for most applications, and both temperature and noise remain low. However, on some occasions I need a bit more speed, more around 75% maybe. Can I set the power saving settings somehow so that the CPU won't surpass 75% of it's capability so that an acceptable compromise between power and noise is achieved? I can't set the CPU frequency in the BIOS and since on rare occasions I'd like to be able to switch to 100% without much hassling, hardware solutions like setting jumpers are no option. This answer to a similar (linux!) question mentions NHC should be able to offer these options, but for me they are all greyed out: The notebook is an Asus Z9200K, I guess NHC doesn't support its chipset enough for these advanced options.

    Read the article

  • Incorrect directory permissions with OpenSSH on Cygwin on Windows Server 2008 SP2

    - by Davy Brion
    I ran into a weird directory permission problem when logged in to a Win2008SP2 (not R2) server through SSH. When I open a local cygwin shell on the server, i can do this: myUser@myServer ~ $ cd /cygdrive/c/Windows/System32/inetsrv/ myUser@myServer /cygdrive/c/Windows/System32/inetsrv $ cd config myUser@myServer /cygdrive/c/Windows/System32/inetsrv/config $ I have no issues accessing the 'config' directory when using a local cygwin shell. 'myUser' has all necessary permissions to access the directory as well. In fact, 'myUser' is a local administrator on the machine. Listing the permissions of the config folder through the local cygwin shell shows the following output: 4 drwx------+ 1 SYSTEM SYSTEM 0 Aug 2 09:38 config But when I log into the server with a SSH client (in this case Putty), i run into the following problem: myUser@myServer ~ $ cd /cygdrive/c/Windows/System32/inetsrv/ myUser@myServer /cygdrive/c/Windows/System32/inetsrv $ cd config -bash: cd: config: Permission denied It also doesn't list the proper permissions through SSH: 0 drwxr-x--- 1 ???????? ???????? 0 Aug 2 09:38 config When I look at the running processes on the server with Task Manager (with a remote desktop connection), it shows that all bash.exe processes are running under the 'myUser' account, so I don't understand why I can't access that particular directory through SSH but have no problems accessing it in a local cygwin shell. I'm using OpenSSH 5.9p1-1. I'm not sure what the Cygwin version is... I used the latest setup.exe (version 2.738) of Cygwin, but I can't seem the find any other Cygwin-related version number. I doubt that it's related to SSH/Cygwin though, because when I connect from the Win2008SP2 server to my local Win7 machine through SSH (using the same OpenSSH/Cygwin versions) I can access the /cygdrive/c/Windows/System32/inetsrv/config folder without issues. Does anyone have an idea on what the issue could be?

    Read the article

  • Google Chrome sync: limit for bookmarks & extensions?

    - by Lyubomyr Shaydariv
    Actually, Chrome is my favorite web-browser, and one of its most powerful features is synchronizing the actual data into a Google account. For the last years I gained a lot of bookmarks and from time to time browse the extensions gallery to find new valuable ones. Really, synchronizing between my work and home PC's freed me from manual sync. And for the recent months I experience strange glitches. I guess it may be caused by a lot of stored bookmarks (potentially about 3K [in estimate], but please don't ask why :)) and extensions (about 130 installed but only 10-15 daily used). I can mention the following strange things: Recently added bookmarks sometimes are not synchronized (e.g. I put a bookmark at work, but it's not guaranteed I can see it that evening), despite about:sync indicates a good sync process. Sometimes recently modified bookmarks appear in either (let's call) last at home or last at work bookmark folders. Sometimes bookmarks are not synced at all. (Moreover, Chromium versions may even crash) Extensions are not synced now at all. Perhaps, there's another reason, but Google Mail Checker and Google Reader Notifier do not show indicators of incoming e-mails and news. ... I'm not sure but it looks like I might exceed Chrome internal sync limits... Is it right? Are there any workarounds, or should I make a massive bookmarks/extensions cleanup (I really don't want it :()? I mostly use Google Chrome Canary builds, and the my current one is 12.0.732.0. Thanks in advance. Update #1 (2001-04-19): I removed about 50 extensions that I'm not interested in (or that I consider as trash), and gained pretty some results: The extensions count is below 100 (exactly 97); The chrome://extensions page does not get slow (or even frozen) any more on enabling/disabling/uninstalling extensions; The extensions are seem to be synchronized now again.

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • how to authenticate once for multiple servers, using only apache configs?

    - by Wang
    My problem is, I have a number of prepackaged web apps (a print system, a wiki, a bug tracker, an email archive, etc.) running on different Mac OS X Leopard (soon to be SL) servers that each need to authenticate users from the internet at large. Right now every server presents an Apache basic authentication prompt, which takes a shared login, but it's apparently enough of an inconvenience to log in repeatedly that people are sending email without checking the wiki or bug tracker or archive. In the case of the bug tracker, a user [might need to log in twice---once for apache if he hasn't used any other protected service on that server, once for the bug tracker itself so it can distinguish different people. Since the only common component to all these apps is Apache 2 itself, does it have any way of authenticating a user once, in some way that will be respected by other servers and various web apps? Looked at http://serverfault.com/questions/32421/how-is-session-stickiness-achieved-across-multiple-web-servers but it sounds like the answer is assuming that I get to write my own web app. Looked at Ian Bicking's blog but it's four years old and recommends something available only for apache 1.3, not apache 2. Sorry not to hyperlink the second site---apparently I need 10 reputation points. Edit: Shibboleth does what I need, but I should have specified that I'm looking for a really dumb, really simple solution for in-house services that need to handle all of a dozen users, probably not more than three at a time.

    Read the article

  • Changes to grub in ubuntu 10

    - by jdege
    I've been running CentOS 5 for some years. I've decided to upgrade to Ubuntu, and with 10.04 just out, this seemed like a good time. I'm a tad paranoid, so I started off with a new set of drives - one to install on, one to backup to, and one as a spare. I removed my existing CentOS 5 drives, and did an install, and had no problems. I installed the server version, and used the default full-disk LVM installation. Next, I copies my backup scripts over, edited them to work with the new configuration, and did a test backup. That worked fine, as well. Then comes the real test, could I do an install of the backup onto the spare drive? (I won't put anything of importance on a system that doesn't have a reliable backup, and if I've never done a restore, it's not reliable.) I booted from a System Rescue CD (ver 1.5.3), with the spare drive as /dev/sda, and the backup drive as /dev/sdb. I had no trouble in partitioning, configuring LVM, formatting, making swap, or restoring the file systems. But when I got to restoring grub to the MBR, I ran into problems. My restore instructions from CentOS 5 said run grub, then enter two commands: root (hd0,0) setup (hd0) The first command exits with an error: "Checking if /boot/grub/stage1 exists ... no" I did some googling around, and found that the Grub2 included in recent Ubuntus is very different than the Grub 0.97 included in CentOS 5. One site suggested I use: grub-install --root-dir=/mnt/restore /dev/sda That appeared to work, but when I booted from the drive, I ended up at a grub prompt. Any ideas as to what I need to do? It seems like a simple problem, but my attempts at searching out answers on the web are being swamped by references to the old version of Grub. Help would be appreciated.

    Read the article

  • Firefox 3.6 and above. Always show one tab even if all tabs are closed like Firefox 3.0

    - by Jayapal Chandran
    I very much got used to Firefox 3.0. In that, to free the memory, I close all tabs but still the main Firefox window does not close. But in Firefox 3.6 and later if I want to close all tabs and if I do so then Firefox totally exists. This is not the case with 3.0. How to stop Firefox from not closing the main process even if I close all threads (tabs)? The autocomplete feature in the address bar of Firefox 3.6 and greater is in a dark blue color which makes me very much annoyed. With my environment and the monitor glare that is inducing anger in me, so how the color be changed to be like Firefox 3.0? Because you know that black and white are a neutral and good combination and since I have been working in Firefox 3.0 (and earlier versions) for a long time this new color change and other uncomfortable options are making me sick. To check CSS3 I need to use Firefox 3.5 and greater. Besides I like Firefox because it includes the W3C's recommendations so I can learn and test new recomendations from W3C.

    Read the article

  • windows 7: Event 55 The file system structure on the disk is corrupt and unusable

    - by Radio
    Here is a real bad one! Windows 7 RTM with SP1 installed [Version 6.1.7601]. Recently tried to delete some folder on my hard drive and Windows prompted "Error 0x80070570: The file or directory is corrupted and unreadable", and at the same time placed an Event 55 describing "The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on \Device\HarddiskVolume2." Ran chkdsk, first with /f option, then with /r option. Result in both cases was: no errors found, 0 bad sectors. No problems chkdsk found at all! Went through StackExchange, Google and spent over 6 hours on this. Still cannot figure out the problem. Re-installing/Re-Formatting is not an option! What did I try: Hotfix - Windows6.1-KB982927-x64.msu - gave me an error about incompatibility with my computer, however it totally matches my system. CRC of hotfix was ok. Windows Repair Console found startup errors and fixed those, but this didn't help an issue, even by running chkdsk c: /R from it. http://support.microsoft.com/kb/246026 does not promise anything good. sfc /scannow does not help too. Replaced hard drive by cloning an old one using True Image, repeated all steps above. At the same time, some minor glitches started to appear in my Windows, like side panel and notification area settings are getting reset. Goal is to delete the folder and get rid of Event 55. Sounds like NTFS bug. Please help. This is completely ridiculous.

    Read the article

  • Effective backup and archive strategy for database and linked files

    - by busyspin
    I am using Postgres to store a variety of application data for a webapp. Part of the application involves storing and retrieving user uploaded files. I am storing the files in the filesystem with some associated metadata in the database. I am trying to come up with a backup and archive strategy so that I can effectively backup and archive/restore the database and the linked files. Here are the things I want to accomplish. Perform routine backups that can be used for recovery from failures and which include all DB data and the linked files. Ideally, this backup would be done while the app is running. Live backup is certainly possible with a DB but I am not sure how to keep the linked files consistent with the database during the backup process Archive chunks of data as they become "old". These chunks must includes the database data plus any linked files. It should be possible to put the archived data back into production again. It would be ideal if it were easy to determine which ranges of objects were stored in each chunk. Do you have any advice for how to accomplish these goals? If the files were in the database as BLOBS these tasks would be much easier since normal database backup and restore functionality would handle this. I am not sure how to accomplish the same thing when file data is linked to database rows.

    Read the article

  • Convert a cassette tape recording to digital format

    - by Electric Automation
    Has anyone been successful with transferring audio cassette tape recordings to a digital format? I would like to preserve old cassette tape recordings of my grandparents to some digital format: MP3, WAV, etc... The quality of the tapes are mediocre. I think I can handle the quality restoration but getting the audio from tape to digital is my question. Below is a list of the hardware that I can work with: Cassette Deck: I have a Technics stereo cassette deck model RS-B12. It has separate left and right IN and OUT RCA type jacks on the back. In the front it has a headphone phono jack, plus left and right mic input phono jacks. On the computer side: -I have a Windows Vista PC with no additional software other than what came with the machine from Costco. No sound editing software that I can see. There is no sound card on the PC. On the front panel there is a mini-phono mic input jack and there are several different types of in/out mini-phono jacks on the back. In addition, USB and Firewire. I also have access to a new (2009) iMac with a mini-phono input jack for a powered mic or other audio source and GarageBand that has come with the computer. In addition, USB and Firewire. What are my options for getting these cassette recordings into a digital format? Whats the best format? What sort of wires would I need and will I want to utilize the USB or Firewire or can I simply use the audio inputs on the PC (or Mac) to receive the audio stream?

    Read the article

  • Should be simple: existing laptop with local user and outlook 2007 migrate on same computer to domain user with outlook 2007 emails intact

    - by bifpowell
    I have Dell Laptop with windows 7 64 bit and for the last year it's been just a machine with an account like: machine\john there are files in folders and stuff in c:\users\john and john uses outlook 2007 as a pop3 client and has identifiable local appdata pst files. Now I installed a server and want to have everything be domain-centric so I added this laptop to the domain with admin credentials and then logged in as a domain user as: domain\john.smith Now I want to duplicate machine\john (outlook emails mostly) to domain\john.smith. In the past I used the Files and Settings Xfer Wizard and done. I tried that here and it crunched away for a while, made the file, but the restore had no effect - it ran for a while, had a progress bar, but it's like nothing happened at all afterwards. I've rebooted the machine, logged in as domain administrator as the first user to log on after the restart and tried: c:\users\john xcopy c:\users\john c:\users\john.smith /V /C /F /H /K /Y /E ...and it copies some of it, but when it gets to c:\users\john.smith\appdata\local\application data it chokes "Access denied, unable to create directory" I also tried logging in as domain\john.smith and copying the entire directory that the PSTs are in from machine\john and a lot of the mail was there when I launched outlook after replacing the PSTs, but not all of them??? I got errors about files in use when doing this method, which I figure must be why not all the old emails are in the inbox?... There must be some extremely simple way to do what must be a very common requirement. Any guidance appreciated.

    Read the article

  • Small Business HP Virtualisation and iSCSI SAN Options

    - by Robin Day
    We are a small business that hosts our core product on a number of HP servers. Our core production setup is 1x HP DL380, high powered for a SQL Server Database 1x HP DL360, mid powered for our core application server 6x HP DL320, low powered for our front ends We run our training / testing / support systems on a similar setup, the servers are just older and less powerful. Unfortunately this is now causing us issues as the system has grown beyond the capabilities of these older servers. Upgrading these servers would be expensive and we believe that virtualisation is probably the way to go for the future. Locally we run a number of test / dev environments on ESXi using Direct Storoage on a couple of high powered DL360's and these are performing fairly well. We're thinking that instead of replacing all of our test servers that we can implement an iSCSI SAN and one or two high powered hosts. Hopefully looking that when it comes to replace our live servers as well that we can just expand the virual environment to cope. So my question is... Can anyone offer any advice on some suitable options? We have generally always been extremely happy with HP servers, all of our kit is currently HP, therefore our preference would be to stick with HP, however, I'm always happy to hear about other options. I'm hoping that initially a budget of around 15-25k (GBP) would be suitable, this could potentially be increased if I had confidence that the system would pave the way for a cost effective upgrade of our live systems in the future as well. I am new to SAN's and my only real experience is playing with OpenFiler on some old desktops. I think iSCSI should be suitable, but I've not done any research into how SQL server may perform. I've had a browser through HP's sites and see plenty of information about EVA, MSA, LeftHand, etc. However, from looking at all that, I don't see which options would be best and more importantly I don't know exactly what I would need to buy. Any help, links, opinions would be much appreciated. Thanks

    Read the article

  • Formatted C: from Windows 7 setup, now it won't even install

    - by ocurro
    Help, I'm so confused. I did more or less what's been described here: I formatted Vista and installed Windows 7 over it. Problem is that I'm now unable to boot (...) [1] I'm installing Seven on top of Vista on ACER AS1410 Notebook When it comes to the part where I choose where to install, I pick the partition labeled C: but instead of keeping windows.old files (what would I want them for?) I choose to go and carelessly format the partition (my bad). It shows me this error: Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information Now the only option is "Load Driver". i have tried installing every single one from ACER website, none of them are useful. I even flashed orig. BIOS. I've tried going back and choose "Repair" like in the picture:[2] but I only get an error: "Failed to save startup options" I think this is weird, what else can I do? [1] superuser.com/questions/117076/formatting-of-an-xp-vista-dual-boot-machine-now-unable-to-boot-up-xp [2] www.howtogeek.com/wp-content/uploads/2007/08/image51.png

    Read the article

  • prevalent, recurring hardrive failure intel macbook from 2006/2007

    - by SimonSalman
    Hi, Long story: My MacBook's hard drive failed one year ago, just a month after its warranty ended or: a year and a month after I bought it. After about ten phone calls to Apple's service, they agreed to extend the warranty for another year, so that I got it replaced free of charge. In the mean time, I got to know that many MacBook users that experience/report hard drive failures. Every reported crash was preceded by a slowdown of system performance, an increased occurrence of the spinning beach ball wait courser, and frequent crashes of applications that used to run very robust until then. It happened (as far as I know) with MacBooks from 2006/2007. All these MacBooks additionally suffer from a recurring wearing down of their "top case". Many heavy users had to replace their HDDs three time since 2006/2007 resulting in an head crash, making it impossible to recover data (diagnosis of recovery specialists) in most but not all cases HDD was Seagate (doesn't necessarily have to be the cause, if majority of the MacBook charge contained Seagate drives) And right now (one year after my first disk crash), these symptoms are cumulating on my system, again ... Short version: prevalent hard drive failure on MacBook charge from 2006/2007 (i.e. 2.16 GHz Intel Core 2 Due) I am looking for any (preferable open source) tool for checking the hard drive condition, especially to detect the known "MacBook problem". So, that I can replace the disk on time. If any Mac user found a solution to prevent the repeated failure of heir hard drive, I would be very glad to get to known it. I really enjoy my old MacBook, but I hate to get interrupted every year by an HDD crash. BTW, the issue is already in discussion for a long time, but there seems to be no solution, so far. Thanks, Simon

    Read the article

  • USB drive dead after stopping copying process on Snow Leopard Server

    - by Anriëtte Combrink
    Hi there I was copying to a flash drive from our Snow Leopard server when I stopped the copying process half way through. The device then disappeared from the Desktop. So I unplugged it and plugged it right back in. The device just didn't show up. I unplugged it and plugged it into a Windows XP machine as well as a Windows 7 machine. On both machines, I right clicked "My Computer" and selected "Manage…". On both PC's, the device was located under Removable Storage, but had no size and no drive letter. It shows up in "My Computer", but when I choose "Format…" from the right-click menu (context menu), it says the drive could not be formatted. Can someone please advise me? The flash drives is about 5 mins old and should have no reason to be dead. I really can't loose this drive (I don't need the data on it, I just need it to work again), any help would be appreciated. Thanks in advance.

    Read the article

  • Filezilla client unable to get directory listing from Filezilla Server (Windows)

    - by sestocker
    I've set up a self signed certificate in FileZilla server and enabled FTP over SSL/TPS. When I connect from the client FileZilla, I am able to authenticate but cannot get a directory listing: Status: Connecting to MY_SERVER_IP:21... Status: Connection established, waiting for welcome message... Response: 220-FileZilla Server version 0.9.39 beta Response: 220-written by Tim Kosse ([email protected]) Response: 220 Please visit http://sourceforge.net/projects/filezilla/ Command: AUTH TLS Response: 234 Using authentication type TLS Status: Initializing TLS... Status: Verifying certificate... Command: USER MYUSER Status: TLS/SSL connection established. Response: 331 Password required for MYUSER Command: PASS ******** Response: 230 Logged on Command: PBSZ 0 Response: 200 PBSZ=0 Command: PROT P Response: 200 Protection level set to P Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is current directory. Command: TYPE I Response: 200 Type set to I Command: PORT 10,10,25,85,219,172 Response: 200 Port command successful Command: MLSD Response: 150 Opening data channel for directory list. Response: 425 Can't open data connection. Error: Failed to retrieve directory listing I have ports 21 and 50001 through 50005 open on the firewall. We are migrating servers - the 50001 - 50005 is one of the things that helped get FTPS working on the old server. I'm not sure this installation would use the same ports? What else could be the problem?

    Read the article

  • Understanding Exchange User Monitor (ExMon) Output

    - by SturdyErde
    I recently downloaded and ran ExMon while trying to troubleshoot Outlook connectivity problems due to high CPU usage on Exchange Server 2010 SP2 UR8. The tool provides a great set of data, but I have not yet figured out how to make great use of it. My first question is why the Exchange Server itself shows up as a high-use MAPI client in the ExMon data. Among the users' client versions I see build numbers listed for Outlook 2013, 2010, and yes, even 2007 clients. I also see build number 14.2.387.0, which represents Exchange Server 2010 SP2 Update Rollup 8 (+/- some other patch that makes it not quite match the UR8 number). There are many user rows that list only "::1" and/or the short hostname of my Exchange server in the 'Client IP Addresses' column. Some other columns include the end-user's actual IP address and the Exchange server's IP address. ExMon shows that it is actually Exchange Server that is utilizing the highest percentage of CPU that is used for MAPI calls. I had expected to see 1 IP address and version number for each user reported by ExMon. Instead, most records show multiple version #'s (Exchange ver and Outlook ver) and multiple IPs (Exchange IP and client IP). Can anyone explain the reason for this to me, please?

    Read the article

  • Scanning website for vulnerablities

    - by Kristen
    I have found that the local school's website installed a Perl Calendar - this was years ago, it has not been used for ages, but Google has it indexed (which is how I found it) and it full of Viagra links and the like ... program was by Matt Kruse, here is details of the exploit: http://www.securiteam.com/exploits/5IP040A1QI.html I've got the school to remove that, but I think they also have MySQL installed and I'm aware that out-of-the-box there have been some exploits of Admin Tools / Login in old versions. For all I know they also have PHPBB and the like installed ... The school is just using some cheap, shared hosting; the HTTP response header I get is: Apache/1.3.29 (Unix) (Red-Hat/Linux) Chili!Soft-ASP/3.6.2 mod_ssl/2.8.14 OpenSSL/0.9.6b PHP/4.4.9 FrontPage/5.0.2.2510 I'm looking for some means of checking if they have other junk installed (quite possibly from way back, and now unused) that might put the site at risk. I'm more interested in something that can scan for things like the MySQL Admin exploit rather than open ports etc. My guess is that they have little control over the hosting space that they have - but I'm a Windows DEV, so this *nix stuff is all Greek to me. I found http://www.beyondsecurity.com/ which looks like it might do what I want (within their evaluation :) ) but I have a worry about how to find out if they are well known / honest - otherwise I will be tipping them a wink with a Domain Name that may be at risk! Many thanks.

    Read the article

< Previous Page | 539 540 541 542 543 544 545 546 547 548 549 550  | Next Page >