Search Results

Search found 22211 results on 889 pages for 'client identifier'.

Page 544/889 | < Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >

• Swap not available on System Monitor

  - by Zaki

  I had a swap partition of 1GB (RAM 1GB, Ubuntu 12.04 lts). Now swap is not shown on System Monitor neither can I hibernate my pc (sudo pm-hibernate). blkid output: /dev/sda1: UUID="B8B4FBB1B4FB706C" TYPE="ntfs" /dev/sda2: UUID="2ea7d608-2d89-4e41-9436-d05cb3ce8871" TYPE="swap" /dev/sda3: UUID="3219d03a-67e4-454b-8ce7-a27831846e35" TYPE="ext4" /dev/sda5: LABEL="Softwares" UUID="AC1CC3301CC2F47C" TYPE="ntfs" /dev/sda6: LABEL="Education" UUID="1E103E6C103E4B53" TYPE="ntfs" /dev/sda7: LABEL="Recreation" UUID="2CC8D181C8D149AA" TYPE="ntfs" /dev/sda8: LABEL="Miscellaneous" UUID="0274D6B174D6A727" TYPE="ntfs" /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda6 during installation UUID=3219d03a-67e4-454b-8ce7-a27831846e35 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=2ea7d608-2d89-4e41-9436-d05cb3ce8871 none swap sw 0 0 free -m total used free shared buffers cached Mem: 991 867 123 0 27 418 -/+ buffers/cache: 421 569 Swap: 0 0 0 cat /proc/swaps Filename Type Size Used Priority fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9f369f36 Device Boot Start End Blocks Id System /dev/sda1 * 63 31471334 15735636 7 HPFS/NTFS/exFAT /dev/sda2 31471616 33470447 999416 82 Linux swap / Solaris /dev/sda3 33472512 62539775 14533632 83 Linux /dev/sda4 62541045 312592769 125025862+ f W95 Ext'd (LBA) /dev/sda5 62541108 125066024 31262458+ 7 HPFS/NTFS/exFAT /dev/sda6 125066088 187591004 31262458+ 7 HPFS/NTFS/exFAT /dev/sda7 187591068 250115984 31262458+ 7 HPFS/NTFS/exFAT /dev/sda8 250116048 312576704 31230328+ 7 HPFS/NTFS/exFAT swapon --all swapon: /dev/sda2: swapon failed: Invalid argument dmesg | grep -A 5 -B 5 -i swap [ 9.487404] EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 131645 [ 9.487413] EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 131330 [ 9.487418] EXT4-fs (sda3): 16 orphan inodes deleted [ 9.487420] EXT4-fs (sda3): recovery complete [ 9.578600] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null) [ 20.580539] Swap area shorter than signature indicates [ 20.588363] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 20.619443] udevd[330]: starting version 175 [ 20.649959] lp: driver loaded but no devices found [ 20.662972] [drm] Initialized drm 1.1.0 20060810 [ 20.675515] i915 0000:00:02.0: setting latency timer to 64 -- [ 72.288573] PM: thaw of drv:sr dev:3:0:0:0 complete after 178.143 msecs [ 72.288578] PM: thaw of drv:scsi_device dev:3:0:0:0 complete after 178.136 msecs [ 72.299677] PM: thaw of drv:scsi_device dev:2:0:0:0 complete after 189.270 msecs [ 72.309473] PM: thaw of devices complete after 202.763 msecs [ 72.309668] PM: writing image. [ 72.309670] PM: Cannot find swap device, try swapon -a. [ 72.309699] PM: Cannot get swap writer [ 72.329896] Restarting tasks ... done. [ 72.331777] PM: Basic memory bitmaps freed [ 72.331792] video LNXVIDEO:00: Restoring backlight state [ 72.420048] option1 ttyUSB0: option_instat_callback: error -84 [ 72.804047] option1 ttyUSB0: option_instat_callback: error -84 -- [ 145.960625] sd 7:0:0:0: Attached scsi generic sg2 type 0 [ 145.972036] sd 7:0:0:0: [sdb] Attached SCSI removable disk [ 172.430508] PPP BSD Compression module registered [ 172.455583] PPP Deflate Compression module registered [ 332.260789] type=1400 audit(1381814763.342:27): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=636 comm="cupsd" pid=636 comm="cupsd" capability=36 capname="block_suspend" [ 1913.030998] Swap area shorter than signature indicates [ 2022.530155] type=1400 audit(1381816453.610:28): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=636 comm="cupsd" pid=636 comm="cupsd" capability=36 capname="block_suspend" [ 4062.729509] Swap area shorter than signature indicates Please help. Thanks in advance. df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 14G 6.1G 7.0G 47% / udev 488M 4.0K 488M 1% /dev tmpfs 199M 868K 198M 1% /run none 5.0M 4.0K 5.0M 1% /run/lock none 496M 224K 496M 1% /run/shm

  Read the article

• Session and Pop Up Window

  - by imran_ku07

   Introduction :        Session is the secure state management. It allows the user to store their information in one page and access in another page. Also it is so much powerful that store any type of object. Every user's session is identified by their cookie, which client presents to server. But unfortunately when you open a new pop up window, this cookie is not post to server with request, due to which server is unable to identify the session data for current user.         In this Article i will show you how to handle this situation,  Description :         During working in a application, i was getting an Exception saying that Session is null, when a pop window opens. After seeing the problem more closely i found that ASP.NET_SessionId cookie for parent page is not post in cookie header of child (popup) window.         Therefore for making session present in both parent and child (popup) window, you have to present same cookie. For cookie sharing i passed parent SessionID in query string,   window.open('http://abc.com/s.aspx?SASID=" & Session.SessionID &','V');           and in Application_PostMapRequestHandler application Event, check if the current request has no ASP.NET_SessionId cookie and SASID query string is not null then add this cookie to Request before Session is acquired, so that Session data remain same for both parent and popup window.    Private Sub Application_PostMapRequestHandler(ByVal sender As Object, ByVal e As EventArgs)           If (Request.Cookies("ASP.NET_SessionId") Is Nothing) AndAlso (Request.QueryString("SASID") IsNot Nothing) Then               Request.Cookies.Add(New HttpCookie("ASP.NET_SessionId", Request.QueryString("SASID")))           End If       End Sub           Now access Session in your parent and child window without any problem. How this works :          ASP.NET (both Web Form or MVC) uses a cookie (ASP.NET_SessionId) to identify the user who is requesting. Cookies are may be persistent (saved permanently in user cookies ) or non-persistent (saved temporary in browser memory). ASP.NET_SessionId cookie saved as non-persistent. This means that if the user closes the browser, the cookie is immediately removed. This is a sensible step that ensures security. That's why ASP.NET unable to identify that the request is coming from the same user. Therefore every browser instance get it's own ASP.NET_SessionId. To resolve this you need to present the same parent ASP.NET_SessionId cookie to the server when open a popup window.           You can confirm this situation by using some tools like Firebug, Fiddler,  Summary :          Hopefully you will enjoy after reading this article, by seeing that how to workaround the problem of sharing Session between different browser instances by sharing their Session identifier Cookie.

  Read the article

• How can I make sound work without starting X?

  - by Magnus Hoff

  I have a headless machine connected to my sound system, and I am using it to run a music playing daemon that I control over the network. (Among other things) However, I can't seem to be able to have sound come out of my speakers without running X. I am running pulse audio in a system wide instance and my daemon is not running within X. Nevertheless, when my daemon is playing music without me hearing it, I can fix it by running startx in an unrelated session. After X starts, I can hear the sound. The sound disappears again if I kill the X server. Interestingly/annoyingly, the sound also stops after X has been running for a few minutes. This could possibly be because of a screen saver of some sort, but I haven't been able to verify or falsify this theory. So my current workaround is to ssh into the box whenever I want music and startx, and restart it every fifteen minutes or so. I'd like to do better. I have been able to verify the following: Adjustments in alsamixer have no effect on this problem. The relevant output channel is never muted In alsamixer, I can see no difference between when the sound is working and when it isn't Nothing is muted in pactl list There is no difference in the output from pactl list between before starting X and after it's started. (Except the identifier of the pactl instance connected to pulse, which is different each time you run pactl) The user running the music daemon is a member of the groups audio, pulse and pulse-access The music daemon program does not report any error messages and acts as if it is playing the music like it should Some form of dbus daemon is running. ps aux|grep dbus reports dbus-daemon --system --fork --activation=upstart before and after I have started X Some details about my hardware: Motherboard: http://www.asus.com/Motherboards/AT5IONTI_DELUXE/ Sound chip: Nvidia GPU 0b HDMI/DP (from alsamixer) Using HDMI for output (Machine also has an Intel Realtek ALC887 that I am not using) Output of lsmod: Module Size Used by deflate 12617 0 zlib_deflate 27139 1 deflate ctr 13201 0 twofish_generic 16635 0 twofish_x86_64_3way 25287 0 twofish_x86_64 12907 1 twofish_x86_64_3way twofish_common 20919 3 twofish_generic,twofish_x86_64_3way,twofish_x86_64 camellia 29348 0 serpent 29125 0 blowfish_generic 12530 0 blowfish_x86_64 21466 0 blowfish_common 16739 2 blowfish_generic,blowfish_x86_64 cast5 25112 0 des_generic 21415 0 xcbc 12815 0 rmd160 16744 0 bnep 18281 2 rfcomm 47604 12 sha512_generic 12796 0 crypto_null 12918 0 parport_pc 32866 0 af_key 36389 0 ppdev 17113 0 binfmt_misc 17540 1 nfsd 281980 2 ext2 73795 1 nfs 436929 1 lockd 90326 2 nfsd,nfs fscache 61529 1 nfs auth_rpcgss 53380 2 nfsd,nfs nfs_acl 12883 2 nfsd,nfs sunrpc 255224 16 nfsd,nfs,lockd,auth_rpcgss,nfs_acl btusb 18332 2 vesafb 13844 2 pl2303 17957 1 ath3k 12961 0 bluetooth 180153 24 bnep,rfcomm,btusb,ath3k snd_hda_codec_hdmi 32474 4 nvidia 11308613 0 ftdi_sio 40679 1 usbserial 47113 6 pl2303,ftdi_sio psmouse 97485 0 snd_hda_codec_realtek 224173 1 snd_hda_intel 33719 5 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel serio_raw 13211 0 snd_seq_midi 13324 0 snd_hwdep 17764 1 snd_hda_codec snd_pcm 97275 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 79041 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device asus_atk0110 18078 0 mac_hid 13253 0 jc42 13948 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm coretemp 13554 0 i2c_i801 17570 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62154 0 Any ideas? What does X do that's so important?

  Read the article

• Sparse virtual machine disk image resizing weirdness?

  - by Matt H

  I have a partitioned virtual machine disk image created by vmware. What I want to do is resize that by 10GB. The file size is showing as 64424509440. Or 60GB. So I ran this: dd if=/dev/zero of=./win7.img seek=146800640 count=0 It ran without errors and I can verify the new size is in fact 75161927680 bytes or 70GB. This is where it gets a little odd. I started the guest domain in xen which is a Windows 7 enterprise machine. What I was expecting to see in diskmgmt.msc is 2 partitions. 1 system partition at the start of around 100MB and near 60GB partition (which is C drive) followed by around 10GB of free space. Actually what I saw was a 70GB partition!?! That confused me... so I decided to run the Check Disk which when you set it on the C drive it asks you to reboot so it'll run on boot. So I did that and during the boot it ran the checks. It got all the way through stage 3 and didn't show any errors at all. Looked at the partitions in disk manager and now C drive has shrunk back to 60GB and there is no free space. What gives? Ok, I thought I'd try mounting it under Dom0 and examining it with fdisk. This is what I get when mounted sudo xl block-attach 0 tap:aio:/home/xen/vms/otoy_v1202-xen.img xvda w sudo fdisk -l /dev/xvda Disk /dev/xvda: 64.4 GB, 64424509440 bytes 255 heads, 63 sectors/track, 7832 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x582dfc96 Device Boot Start End Blocks Id System /dev/xvda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/xvda2 13 7833 62810112 7 HPFS/NTFS Note the cylinder boundary comment. When I run sudo cfdisk /dev/xvda I get: FATAL ERROR: Bad primary partition 1: Partition ends in the final partial cylinder Press any key to exit cfdisk So I guess this is a bigger problem than first thought. How can I fix this? EDIT: Oops, the cylinder boundary thing is not a problem at all since disks have used LBA etc. So that threw me for a moment... still the problem exists... Now this output looks a little different. sudo sfdisk -uS -l /dev/xvda Disk /dev/xvda: 7832 cylinders, 255 heads, 63 sectors/track Units = sectors of 512 bytes, counting from 0 Device Boot Start End #sectors Id System /dev/xvda1 * 2048 206847 204800 7 HPFS/NTFS /dev/xvda2 206848 125827071 125620224 7 HPFS/NTFS /dev/xvda3 0 - 0 0 Empty /dev/xvda4 0 - 0 0 Empty BTW: I do have a backup of the image so if you help me mess it up that's ok. EDIT: sudo parted /dev/xvda print free Model: Xen Virtual Block Device (xvd) Disk /dev/xvda: 64.4GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 32.3kB 1049kB 1016kB Free Space 1 1049kB 106MB 105MB primary ntfs boot 2 106MB 64.4GB 64.3GB primary ntfs 64.4GB 64.4GB 1049kB Free Space Cool. Linux is showing free space is 10GB which is what I expect. The problem is windows isn't seeing this?

  Read the article

• A developer&rsquo;s WBS &ndash; 3 factors of 5

  - by johndoucette

  As a development manager, I have requested work breakdown structures (WBS) many times from the dev leads. Everyone has their own approach and why it takes sometimes days to get this simple list is often frustrating. Here is a simple way to get that elusive WBS done in 30 minutes and have 125 items in your list – well, 126. The WBS is made up of parent-child entities representing the overall outcome of the project. At the bottom of the hierarchical list should be the task item that a developer would perform in support of the branch in the list or WBS. Because I work with different dev leads on every project, I always ask the “what time value would you like to see at the lowest task in order to assign it to a developer and ensure it gets done within the timeframe”. I am particular to a task being 8 hours. Some like 8 to 24 hours. Stay away from tasks defaulting to 1 week. The task becomes way to vague and hard to manage completeness, especially on short budgets. As a developer, your focus is identifying the tasks you to accomplish in order to deliver the product. As a project manager, you will take the developer's WBS and add all the “other stuff” like quality testing, meetings, documentation, transition to maintenance, etc… Start your exercise with the name of the product you are delivering as a result of the project. You should be able to represent what you are building and deploying with one to three words. Example; XYZ Public Website Middleware BizTalk Application The reason you start with that single identifier is to always see the list as the product. It helps during each of the next three passes. Now, choose 5 tasks which in their entirety represent the product you will be delivering and add them to list under the product name you created earlier; Public Website     Security     Sites     Infrastructure     Publishing     Creative Continue this concept of seeing the list as the complete picture and decompose it one more level. You should have 25 items. Public Website     Security         Authentication         Login Control         Administration         DRM         Workflow     Sites         Masterpages         Page Layouts         Web Parts (RIA, Multimedia)         Content Types         Structures     Infrastructure         ...     Publishing         ...     Creative         ... And one more time for a total of 125 items. The top item makes the list 126. Public Website     Security         Authentication             Install (AD/ADAM/LDAP/SQL)             Configuration             Management             Web App Configuration             Implement Provider         Login Control             Login Form             Login/Logoff             pw change             pw recover/forgot             email verification         Administration             ...         DRM             ...         Workflow             ...     Sites         Masterpages         Page Layouts         Web Parts (RIA, Multimedia)         Content Types         Structures     Infrastructure         ...     Publishing         ...     Creative         ... The next step is to make sure the task at the bottom of every branch represents the “time value” you planned for the project. You can add more to the WBS and of course if you can’t find 5 items, 4 is fine. If a task can be done in a fraction of the time value you determined for the project, try to roll it up into a larger task. In the task actions (later when the iteration is being planned), decompose the details back to the simple tasks. Now, go estimate!

  Read the article

• disks not ready in array causes mdadm to force initramfs shell

  - by RaidPinata

  Okay, this is starting to get pretty frustrating. I've read most of the other answers on this site that have anything to do with this issue but I'm still not getting anywhere. I have a RAID 6 array with 10 devices and 1 spare. The OS is on a completely separate device. At boot only three of the 10 devices in the raid are available, the others become available later in the boot process. Currently, unless I go through initramfs I can't get the system to boot - it just hangs with a blank screen. When I do boot through recovery (initramfs), I get a message asking if I want to assemble the degraded array. If I say no and then exit initramfs the system boots fine and my array is mounted exactly where I intend it to. Here are the pertinent files as near as I can tell. Ask me if you want to see anything else. # mdadm.conf # # Please refer to mdadm.conf(5) for information about this file. # # by default (built-in), scan all partitions (/proc/partitions) and all # containers for MD superblocks. alternatively, specify devices to scan, using # wildcards if desired. #DEVICE partitions containers # auto-create devices with Debian standard permissions # CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR root # definitions of existing MD arrays # This file was auto-generated on Tue, 13 Nov 2012 13:50:41 -0700 # by mkconf $Id$ ARRAY /dev/md0 level=raid6 num-devices=10 metadata=1.2 spares=1 name=Craggenmore:data UUID=37eea980:24df7b7a:f11a1226:afaf53ae Here is fstab # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sdc2 during installation UUID=3fa1e73f-3d83-4afe-9415-6285d432c133 / ext4 errors=remount-ro 0 1 # swap was on /dev/sdc3 during installation UUID=c4988662-67f3-4069-a16e-db740e054727 none swap sw 0 0 # mount large raid device on /data /dev/md0 /data ext4 defaults,nofail,noatime,nobootwait 0 0 output of cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid6 sda[0] sdd[10](S) sdl[9] sdk[8] sdj[7] sdi[6] sdh[5] sdg[4] sdf[3] sde[2] sdb[1] 23441080320 blocks super 1.2 level 6, 512k chunk, algorithm 2 [10/10] [UUUUUUUUUU] unused devices: <none> Here is the output of mdadm --detail --scan --verbose ARRAY /dev/md0 level=raid6 num-devices=10 metadata=1.2 spares=1 name=Craggenmore:data UUID=37eea980:24df7b7a:f11a1226:afaf53ae devices=/dev/sda,/dev/sdb,/dev/sde,/dev/sdf,/dev/sdg,/dev/sdh,/dev/sdi,/dev/sdj,/dev/sdk,/dev/sdl,/dev/sdd Please let me know if there is anything else you think might be useful in troubleshooting this... I just can't seem to figure out how to change the boot process so that mdadm waits until the drives are ready to build the array. Everything works just fine if the drives are given enough time to come online. edit: changed title to properly reflect situation

  Read the article

• How to get faster graphics in KVM? VNC is painfully slow with Haiku OS guest, Spice won't install and SDL doesn't work

  - by Don Quixote

  I've been coming up to speed on the Haiku operating system, an Open Source clone of BeOS 5 Pro. I'm using an Apple MacBook Pro as my development machine. Apple's BootCamp BIOS does not support more than four partitions on the internal hard drive. While I can set up extended and logical partitions, doing so will prevent any of the installed operating systems from booting. To run Haiku directly on the iron, I boot it off a USB stick. Using external storage is also helpful because I am perpetually out of filesystem space. While VirtualBox is documented to allow access to physical drives, I could not actually get it to work. Also VirtualBox can only use one of the host CPU's cores. While VB guests can be configured for more than one CPU, they are only emulated. A full build of the Haiku OS takes 4.5 under VB. I had the hope of reducing build times by using KVM instead, but it's not working nearly as well as VirtualBox did. The Linux Kernel Virtual Machine is broken in all manner of fundamental ways as seen from Haiku. But I'm a coder; maybe I could contribute to fixing some of those problems. The first problem I've got is that Haiku's video in virt-manager is quite painfully slow. When I drag Haiku windows around the desktop, they lag quite far behind where my mouse is. It's quite difficult to move a window to a precise position on the screen. Just imagine that the mouse was connected to the window title bar with a really stretchy spring. Also Haiku's mouse lags quite far behind where I have moved it. I found lots of Personal Package Archives that enable Spice from QEMU / KVM at the Ubuntu Personal Package Arhives. I tried a few of the PPAs but none of them worked; with one of them, the command "add-apt-repository" crashed with a traceback. There is a Wiki page about Spice, but it says that it only works on 64-bit. My Early 2006 MacBook Pro is 32-bit. Its Apple Model Identifier is MacBookPro1,1; these use Core Duos NOT Core 2 Duos. I don't mind building a source deb for 32-bit if I can expect it to work. Is there some reason that Spice should be 64-bit only? Does it need features of the x86_64 Instruction Set Architecture that x86 does not have? When I try using SDL from virt-manager, the configuration for Local SDL Window says "Xauth: /home/mike/.Xauthority". When I try to start my guest, virt-manager emits an error. When I Googled the error message, the usual solution was to make ~/.Xauthority readible. However, .Xauthorty does not exist in my home directory. Instead I have a $XAUTHORITY environment variable. There is no way to configure SDL in virt-manager to use $XAUTHORITY instead of ~/.Xauthority. Neither does it work to copy the value of $XAUTHORITY into the file. I am ready to scream, because I've been five fscking days trying to make KVM work for Haiku development. There is a whole lot more that is broken than the slow video. All I really want to do for now is speed up my full builds of Haiku by using "jam -j2" to use both cores in my CPU. I may try Xen next, but the last time I monkeyed with Xen it was far, far more broken than I am finding KVM to be. Just for now, I would be satisfied if there were some way to use my USB stick as a drive in VirtualBox. VB does allow me to configure /dev/sdb as a drive, but it always causes a fatal error when I try to launch the guest. Thank You For Any Advice You Can Give Me. -

  Read the article

• Designing An ACL Based Permission System

  - by ryanzec

  I am trying to create a permissions system where everything is going to be stored in MySQL (or some database) and pulled using PHP for a project management system I am building.  I am right now trying to do it is an ACL kind of way.  There are a number key features I want to be able to support: 1.  Being able to assign permissions without being tied to a specific object. The reason for this is that I want to be able to selectively show/hide elements of the UI based on permissions at a point where I am not directly looking at a domain object instance.  For instance, a button to create a new project should only should only be shown to users that have the pm.project.create permission but obviously you can assign a create permission to an domain object instance (as it is already created). 2.  Not have to assign permissions for every single object. Obviously creating permissions entries for every single object (projects, tickets, comments, etc…) would become a nightmare to maintain so I want to have some level of permission inheritance. *3.  Be able to filter queries based on permissions. This would be a really nice to have but I am not sure if it is possible.  What I mean by this is say I have a page that list all projects.  I want the query that pulls all projects to incorporate the ACL so that it would not show projects that the current user does not have pm.project.read access to.  This would have to be incorporated into the main query as if it is a process that is done after that main query (which I know I could do) certain features like pagination become much more difficult. Right now this is my basic design for the tables: AclEntities id - the primary key key - the unique identifier for the domain object (usually the primary key of that object) parentId - the parent of the domain object (like the project object if this was a ticket object) aclDomainObjectId - metadata about the domain object AclDomainObjects id - primary key title - simple string to unique identify the domain object(ie. project, ticket, comment, etc…) fullyQualifiedClassName - the fully qualified class name for use in code (I am using namespaces) There would also be tables mapping AclEntities to Users and UserGroups. I also have this interface that all acl entity based object have to implement: IAclEntity getAclKey() - to the the unique key for this specific instance of the acl domain object (generally return the primary key or a concatenated string of a composite primary key) getAclTitle() - to get the unique title for the domain object (generally just returning a static string) getAclDisplayString() - get the string that represents this entity (generally one or more field on the object) getAclParentEntity() - get the parent acl entity object (or null if no parent) getAclEntity() - get the acl enitty object for this instance of the domain object (or null if one has not been created yet) hasPermission($permissionString, $user = null) - whether or not the user has the permission for this instance of the domain object static getFromAclEntityId($aclEntityId) - get a specific instance of the domain object from an acl entity id. Do any of these features I am looking for seems hard to support or are just way off base? Am I missing or not taking in account anything in my implementation? Is performance something I should keep in mind?

  Read the article

• Not enough free disk space

  - by carmatt95

  I'm new to Ubuntu and I'm getting an error in software updater. When I try and do my daily updates, it says: The upgrade needs a total of 25.3 M free space on disk /boot. Please free at least an additional 25.3 M of disk space on /boot. Empty your trash and remove temporary packages of former installations using sudo apt-get clean. I tried typing in sudo apt-get clean into the terminal but I still get the message. All of the pages I read seem to be for experianced Ubuntuers. Any help would be appreciated. I'm running Ubuntu 12.10. I want to upgrade to 13.04 but understand I have to finish these first. EDIT: @Alaa, This is the output from typing in cat /etc/fstab into the terminal: # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> /dev/mapper/ubuntu-root / ext4 errors=remount-ro 0 1 # /boot was on /dev/sda1 during installation UUID=fa55c082-112d-4b10-bcf3-e7ffec6cebbc /boot ext2 defaults 0 2 /dev/mapper/ubuntu-swap_1 none swap sw 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto,exec,utf8 0 0 matty@matty-G41M-ES2L:~$ df -h: Filesystem Size Used Avail Use% Mounted on /dev/mapper/ubuntu-root 915G 27G 842G 4% / udev 984M 4.0K 984M 1% /dev tmpfs 397M 1.1M 396M 1% /run none 5.0M 0 5.0M 0% /run/lock none 992M 1.8M 990M 1% /run/shm none 100M 52K 100M 1% /run/user /dev/sda1 228M 222M 0 100% /boot matty@matty-G41M-ES2L:~$ dpkg -l | grep linux-image: ii linux-image-3.5.0-17-generic 3.5.0-17.28 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-18-generic 3.5.0-18.29 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-19-generic 3.5.0-19.30 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-21-generic 3.5.0-21.32 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-22-generic 3.5.0-22.34 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-23-generic 3.5.0-23.35 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-24-generic 3.5.0-24.37 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-25-generic 3.5.0-25.39 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-26-generic 3.5.0-26.42 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP iF linux-image-3.5.0-28-generic 3.5.0-28.48 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP

  Read the article

• Can anybody help me in designing my UITableView into MVC Pattern ?

  - by user2877880

  I have written a ViewController in which i get data from the internet and display it in a UItableview using a json parser which uses object for key to identify its objects. What i would like your help in is to convert it into MVC pattern to make it less clumsy instead of including everything in the same controller class. Please try explaining it to me in terms of my code. THANKS IN ADVANCE. The code is as given below #import "ViewController.h" #import "AFNetworking.h" #import "ModelTableArray.h" @implementation ViewController @synthesize tableView = _tableView, activityIndicatorView = _activityIndicatorView, movies = _movies; - (void)viewDidLoad { [super viewDidLoad]; // Setting Up Table View self.tableView = [[UITableView alloc] initWithFrame:CGRectMake(0.0, 0.0, self.view.bounds.size.width, self.view.bounds.size.height) style:UITableViewStylePlain]; self.tableView.dataSource = self; self.tableView.delegate = self; self.tableView.autoresizingMask = UIViewAutoresizingFlexibleWidth | UIViewAutoresizingFlexibleHeight; self.tableView.hidden = YES; [self.view addSubview:self.tableView]; // Setting Up Activity Indicator View self.activityIndicatorView = [[UIActivityIndicatorView alloc] initWithActivityIndicatorStyle:UIActivityIndicatorViewStyleGray]; self.activityIndicatorView.hidesWhenStopped = YES; self.activityIndicatorView.center = self.view.center; [self.view addSubview:self.activityIndicatorView]; [self.activityIndicatorView startAnimating]; // Initializing Data Source self.movies = [[NSArray alloc] init]; NSURL *url = [[NSURL alloc] initWithString:@"http://itunes.apple.com/search?term=rocky&country=us&entity=movie"]; NSURLRequest *request = [[NSURLRequest alloc] initWithURL:url]; UIRefreshControl *refreshControl = [[UIRefreshControl alloc] init]; [refreshControl addTarget:self action:@selector(refresh:) forControlEvents:UIControlEventValueChanged]; [self.tableView addSubview:refreshControl]; [refreshControl endRefreshing]; AFJSONRequestOperation *operation = [AFJSONRequestOperation JSONRequestOperationWithRequest:request success:^(NSURLRequest *request, NSHTTPURLResponse *response, id JSON) { self.movies = [JSON objectForKey:@"results"]; [self.activityIndicatorView stopAnimating]; [self.tableView setHidden:NO]; [self.tableView reloadData]; } failure:^(NSURLRequest *request, NSHTTPURLResponse *response, NSError *error, id JSON) { NSLog(@"Request Failed with Error: %@, %@", error, error.userInfo); }]; [operation start]; } - (void)refresh:(UIRefreshControl *)sender { NSURL *url = [[NSURL alloc] initWithString:@"http://itunes.apple.com/search?term=rambo&country=us&entity=movie"]; NSURLRequest *request = [[NSURLRequest alloc] initWithURL:url]; AFJSONRequestOperation *operation = [AFJSONRequestOperation JSONRequestOperationWithRequest:request success:^(NSURLRequest *request, NSHTTPURLResponse *response, id JSON) { self.movies = [JSON objectForKey:@"results"]; [self.activityIndicatorView stopAnimating]; [self.tableView setHidden:NO]; [self.tableView reloadData]; } failure:^(NSURLRequest *request, NSHTTPURLResponse *response, NSError *error, id JSON) { NSLog(@"Request Failed with Error: %@, %@", error, error.userInfo); }]; [operation start]; [sender endRefreshing]; } - (void)viewDidUnload { [super viewDidUnload]; } - (BOOL)shouldAutorotateToInterfaceOrientation:(UIInterfaceOrientation)interfaceOrientation { return YES; } // Table View Data Source Methods - (NSInteger)tableView:(UITableView *)tableView numberOfRowsInSection:(NSInteger)section { if (self.movies && self.movies.count) { return self.movies.count; } else { return 0; } } - (UITableViewCell *)tableView:(UITableView *)tableView cellForRowAtIndexPath:(NSIndexPath *)indexPath { static NSString *cellID = @"Cell Identifier"; UITableViewCell *cell = [tableView dequeueReusableCellWithIdentifier:cellID]; if (!cell) { cell = [[UITableViewCell alloc] initWithStyle:UITableViewCellStyleSubtitle reuseIdentifier:cellID]; } NSDictionary *movie = [self.movies objectAtIndex:indexPath.row]; cell.textLabel.text = [movie objectForKey:@"trackName"]; cell.detailTextLabel.text = [movie objectForKey:@"artistName"]; NSURL *url = [[NSURL alloc] initWithString:[movie objectForKey:@"artworkUrl100"]]; [cell.imageView setImageWithURL:url placeholderImage:[UIImage imageNamed:@"placeholder"]]; return cell; } @end

  Read the article

• How to handle multi-processing of libraries which already spawn sub-processes?

  - by exhuma

  I am having some trouble coming up with a good solution to limit sub-processes in a script which uses a multi-processed library and the script itself is also multi-processed. Both, the library and script are modifiable by us. I believe the question is more about design than actual code, but for what it's worth, it's written in Python. The goal of the library is to hide implementation details of various internet routers. For that reason, the library has a "Proxy" factory method which takes the IP of a router as parameter. The factory then probes the device using a set of possible proxies. Usually, there is one proxy which immediately knows that is is able to send commands to this device. All others usually take some time to return (given a timeout). One thought was already to simply query the device for an identifier, and then select the proper proxy using that, but in order to do so, you would already need to know how to query the device. Abstracting this knowledge is one of the main purposes of the library, so that becomes a little bit of a "circular-requirement"/deadlock: To connect to a device, you need to know what proxy to use, and to know what proxy to create, you need to connect to a device. So probing the device is - as we can see - the best solution so far, apart from keeping a lookup-table somewhere. The library currently kills all remaining processes once a valid proxy has been found. And yes, there is always only one good proxy per device. Currently there are about 12 proxies. So if one create a proxy instance using the factory, 12 sub-processes are spawned. So far, this has been really useful and worked very well. But recently someone else wanted to use this library to "broadcast" a command to all devices. So he took the library, and wrote his own multi-processed script. This obviously spawned 12 * n processes where n is the number of IPs to which he broadcasted. This has given us two problems: The host on which the command was executed slowed down to a near halt. Aborting the script with CTRL+C ground the system to a total halt. Not even the hardware console responded anymore! This may be due to some Python strangeness which still needs to be investigated. Maybe related to http://bugs.python.org/issue8296 The big underlying question, is how to design a library which does multi-processing, so other applications which use this library and want to be multi-processed themselves do not run into system limitations. My first thought was to require a pool to be passed to the library, and execute all tasks in that pool. In that way, the person using the library has control over the usage of system resources. But my gut tells me that there must be a better solution. Disclaimer: My experience with multiprocessing is fairly limited. I have implemented a few straightforward which did not require access control to resources. So I have not yet any practical experience with semaphores or mutexes. p.s.: In the future, we may have enough information to do this without the probing. But the database which would contain the proper information is not yet operational. Also, the design about multiprocessing a multiprocessed library intrigues me :)

  Read the article

• Postfix - am I sending spam?

  - by olrehm

  today I received like 30 messages within 5 minutes telling me that some mail I send could not be delivered, mostly to *.ru email addresses which I did not send any mail to. I have my own webserver (postfix/dovecot) set up using this guide (http://workaround.org/ispmail/lenny) but adjusted a little bit for Ubuntu. I tested whether I am an Open Relay which I am apparently not. Now there are two possible reasons for the above mentioned emails: Either I am sending out spam, or somebody wants me to think that, correct? How can I check this? I selected one particular address that I supposedly send spam to. Then I searched my mail.log for this entry. I found two blocks that record that somebody from the server connected to my server and delivered some message to two different users. I cannot find an entry reporting that anyone from my server send an email to that server. Does this mean its just some mail to scare me or could it still have been send by me in the first place? Here is one such block from the log (I replaced some confidential stuff): Jun 26 23:23:28 mycustomernumber postfix/smtpd[29970]: connect from mx.webstyle.ru[195.144.251.97] Jun 26 23:23:29 mycustomernumber postfix/smtpd[29970]: 044991528995: client=mx.webstyle.ru[195.144.251.97] Jun 26 23:23:29 mycustomernumber postfix/cleanup[29974]: 044991528995: message-id=<[email protected]> Jun 26 23:23:29 mycustomernumber postfix/qmgr[3369]: 044991528995: from=<>, size=2198, nrcpt=1 (queue active) Jun 26 23:23:29 mycustomernumber amavis[28598]: (28598-11) ESMTP::10024 /var/lib/amavis/tmp/amavis-20110626T223137-28598: <> -> <[email protected]> SIZE=2198 Received: from mycustomernumber.stratoserver.net ([127.0.0.1]) by localhost (rehmsen.de [127.0.0.1]) (amavisd-new, port 10024) with ESMTP for <[email protected]>; Sun, 26 Jun 2011 23:23:29 +0200 (CEST) Jun 26 23:23:29 mycustomernumber amavis[28598]: (28598-11) Checking: YakjkrdFq6A8 [195.144.251.97] <> -> <[email protected]> Jun 26 23:23:29 mycustomernumber postfix/smtpd[29970]: disconnect from mx.webstyle.ru[195.144.251.97] Jun 26 23:23:29 mycustomernumber amavis[28598]: (28598-11) lookup_sql_field(id) (WARN: no such field in the SQL table), "[email protected]" result=undef Jun 26 23:23:32 mycustomernumber postfix/smtpd[29979]: connect from localhost.localdomain[127.0.0.1] Jun 26 23:23:32 mycustomernumber postfix/smtpd[29979]: 0A1FA1528A21: client=localhost.localdomain[127.0.0.1] Jun 26 23:23:32 mycustomernumber postfix/cleanup[29974]: 0A1FA1528A21: message-id=<[email protected]> Jun 26 23:23:32 mycustomernumber postfix/qmgr[3369]: 0A1FA1528A21: from=<>, size=2841, nrcpt=1 (queue active) Jun 26 23:23:32 mycustomernumber postfix/smtpd[29979]: disconnect from localhost.localdomain[127.0.0.1] Jun 26 23:23:32 mycustomernumber amavis[28598]: (28598-11) FWD via SMTP: <> -> <[email protected]>,BODY=7BIT 250 2.0.0 Ok, id=28598-11, from MTA([127.0.0.1]:10025): 250 2.0.0 Ok: queued as 0A1FA1528A21 Jun 26 23:23:32 mycustomernumber amavis[28598]: (28598-11) Passed CLEAN, [195.144.251.97] [195.144.251.97] <> -> <[email protected]>, Message-ID: <[email protected]>, mail_id: YakjkrdFq6A8, Hits: 2.249, size: 2197, queued_as: 0A1FA1528A21, 2882 ms Jun 26 23:23:32 mycustomernumber postfix/smtp[29975]: 044991528995: to=<[email protected]>, relay=127.0.0.1[127.0.0.1]:10024, delay=3.3, delays=0.39/0.01/0.01/2.9, dsn=2.0.0, status=sent (250 2.0.0 Ok, id=28598-11, from MTA([127.0.0.1]:10025): 250 2.0.0 Ok: queued as 0A1FA1528A21) Jun 26 23:23:32 mycustomernumber postfix/qmgr[3369]: 044991528995: removed Jun 26 23:23:33 mycustomernumber postfix/smtp[29980]: 0A1FA1528A21: to=<[email protected]>, orig_to=<[email protected]>, relay=mx3.hotmail.com[65.54.188.110]:25, delay=1.2, delays=0.15/0.02/0.51/0.55, dsn=2.0.0, status=sent (250 <[email protected]> Queued mail for delivery) Jun 26 23:23:33 mycustomernumber postfix/qmgr[3369]: 0A1FA1528A21: removed Jun 26 23:26:49 mycustomernumber postfix/anvil[29972]: statistics: max connection rate 1/60s for (smtp:195.144.251.97) at Jun 26 23:23:28 Jun 26 23:26:49 mycustomernumber postfix/anvil[29972]: statistics: max connection count 1 for (smtp:195.144.251.97) at Jun 26 23:23:28 Jun 26 23:26:49 mycustomernumber postfix/anvil[29972]: statistics: max cache size 1 at Jun 26 23:23:28 I can provide more info if you tell me what you need to know. Thank you for you help!

  Read the article

• Teamviewer: cannot control monitor 1, but can control monitor 2

  - by DaveT

  I'm using the web client of Teamviewer from my work computer trying to control my home computer. I have 2 monitors on the remote desktop, but for some reason only have control on the second monitor. When I switch to the main monitor (monitor 1), I cannot do anything and cannot even move the cursor. But I have no issues when I switch over to the second monitor (monitor 2). I used to have no issues with either, but in the past couple of months this has been causing me issues. Anyone have a suggestion? Thanks!! Also... Here is the log from the Teamviewer session. Showing me switching back and forth between the monitors. (just in case this will help). I had to remove the links in order to post the log since I don't have enough reputation points, but they were just teamviewer login weblinks. =============================================================================== 21.08 16:00:41,176: Version: 9.0.15099 21.08 16:00:41,177: Sandbox: remote 21.08 16:00:41,177: SysLanguage: en 21.08 16:00:41,177: VarLanguage: en 21.08 16:00:41,177: Flash Player: PlugIn (WIN 14,0,0,179) 21.08 16:00:41,178: UseLanguage: en 21.08 16:00:41,178: UseLanguage: en 21.08 16:00:41,182: TeamViewer hasPassword: true 21.08 16:00:41,418: ExternalConnect id=910035824 21.08 16:00:41,419: CT connect 910035824 masterURL: , sandbox = remote 21.08 16:00:41,425: MC.requestRoute(910035824) 21.08 16:00:41,426: MC.sendMasterCommand text=F=RequestRoute2&ID1=777&Client=TV& ID2=910035824&SA_AccountID=26641022&SA_PasswordMD5HashBase64Encoded=& SA_SessionSecret=f7H6Z7SYfX5ahQ7SJq/r/K20PBYg9fOZhp+DKLhf5ts=&SA_SessionID=1558929948& V=9.0.15099&OS=Flash 21.08 16:00:41,426: MC wait for ping completion 21.08 16:00:42,064: PS.socket event: [Event type="connect" bubbles=false cancelable=false eventPhase=2] 21.08 16:00:42,182: PingThread: TCP-Ping ok 21.08 16:00:42,183: MC.socket mode = TCP, MasterURL: 21.08 16:00:42,183: MC.connect: 21.08 16:00:43,058: PS.socket event: [Event type="connect" bubbles=false cancelable=false eventPhase=2] 21.08 16:00:43,058: MC.connectHandler: [Event type="connect" bubbles=false cancelable=false eventPhase=2] 21.08 16:00:43,236: MC.requestRouteResponse: [email protected]_10800_128000_762319420_910035824_10000__1_0_16778176_128000_16778176: 128000;2147483647:1280000;4:640000_786297_786297 21.08 16:00:43,239: CT init socket: TCP 21.08 16:00:43,513: PS.socket event: [Event type="connect" bubbles=false cancelable=false eventPhase=2] 21.08 16:00:43,514: CT.connectHandler: [Event type="connect" bubbles=false cancelable=false eventPhase=2] 21.08 16:00:43,519: Browser name: Netscape 21.08 16:00:43,936: CMD_IDENTIFY id=910035824 ver=2.41 21.08 16:00:44,666: CMD_CONFIRMENCRYPTION: encryption confirmed 21.08 16:00:44,667: Started resendrequest timer 21.08 16:00:45,063: Remote Version: TV 009.000 21.08 16:00:45,501: start classic authentication 21.08 16:00:45,502: Login::SendRequestToConsole(): url= 21.08 16:00:45,828: start srp authentication 21.08 16:00:46,983: checkFirstPacket ok, m_LastReceivedPacketID =4 21.08 16:00:47,148: Login::SendRequestToConsole(): url= 21.08 16:00:47,478: start srp authentication 21.08 16:00:48,210: Login::SendRequestToConsole(): url= 21.08 16:00:48,485: checkFirstPacket ok, m_LastReceivedPacketID =7 21.08 16:00:48,780: TVCmdAuthenticate_Authenticated: 1 21.08 16:00:49,321: Connected to 910035824, name=NEWMAN, os=14, version=9.0.31064 21.08 16:00:49,329: ConnectionAccessSettings: RemoteControl: AllowedFileTransfer: AllowedControlRemoteTV: AllowedSwitchSides: DeniedAllowDisableRemoteInput: AllowedAllowVPN: AllowedAllowPartnerViewDesktop: Allowed 21.08 16:00:52,195: unexpected TVCommand.CommandType == 56 21.08 16:00:52,231: CW received display params: 1680x1050x8 monitors: 2 (active:0) 21.08 16:00:52,301: Caching active, version=2 21.08 16:03:47,158: CW received display params: 1680x1050x8 monitors: 2 (active:1) 21.08 16:04:24,447: CW received display params: 1680x1050x8 monitors: 2 (active:0) 21.08 16:04:40,609: CW received display params: 3360x1050x8 monitors: 2 (active:-1) 21.08 16:04:59,802: CW received display params: 1680x1050x8 monitors: 2 (active:1) 21.08 16:04:59,933: CW received display params: 1680x1050x8 monitors: 2 (active:1) 21.08 16:05:58,419: CW received display params: 1680x1050x8 monitors: 2 (active:0) 21.08 16:06:36,824: CW received display params: 1680x1050x8 monitors: 2 (active:1) 21.08 16:07:07,232: CW received display params: 1680x1050x8 monitors: 2 (active:0)

  Read the article

• OpenVPN: Connection established but can’t connect to server

  - by Maik

  I am trying to set up OpenVPN to allow me to connect a number of laptops to my network in a way that allows the laptops to connect to specific computers via HTTP (to e.g. a server management page) and windows shares (to access files) In the test environment my laptops live in a network with a 192.168.1.X address range. The host-network has a 10.66.77.X address range The server hosting the OpenVPN server has address 10.77.10.20. I need to access some application server web pages on this machine, accessible on various ports The server with the windows shares as well as some other web based pages I need to access is on address 10.66.77.20 The config files for server and laptop are attached below. The laptop establishes the VPN connection without problems, but I cannot access any of the machines, even a simple ping fails. Maybe a routing problem? The routing table for the laptop is shown below as well - every idea is appreciated! Thanks! Maik Server config file port 1194 dev tun tls-server ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/projects.crt key /etc/openvpn/keys/projects.key dh /etc/openvpn/keys/dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "route 10.66.77.0 255.255.255.0" keepalive 10 60 inactive 600 route 10.8.0.1 255.255.255.0 user openvpn group openvpn persist-tun persist-key verb 4 client config file dev tun proto udp remote SERVERADDR 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert accountingLaptop.crt key accountingLaptop.key ns-cert-type server comp-lzo verb 3 Resulting routing table on client laptop C:\Documents and Settings\User>route print =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 23 5a 9b 64 9b ...... Atheros AR8132 PCI-E Fast Ethernet Controller - Packet Scheduler Miniport 0x3 ...00 24 2c 35 c9 6b ...... Dell Wireless 1395 WLAN Mini-Card - Packet Sched uler Miniport 0x4 ...00 ff 5e 03 43 9b ...... TAP-Win32 Adapter V9 - Packet Scheduler Miniport =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.129 25 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 1 10.8.0.4 255.255.255.252 10.8.0.6 10.8.0.6 30 10.8.0.6 255.255.255.255 127.0.0.1 127.0.0.1 30 10.66.77.0 255.255.255.0 10.8.0.5 10.8.0.6 1 10.255.255.255 255.255.255.255 10.8.0.6 10.8.0.6 30 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.1.0 255.255.255.0 192.168.1.129 192.168.1.129 25 192.168.1.129 255.255.255.255 127.0.0.1 127.0.0.1 25 192.168.1.255 255.255.255.255 192.168.1.129 192.168.1.129 25 224.0.0.0 240.0.0.0 10.8.0.6 10.8.0.6 30 224.0.0.0 240.0.0.0 192.168.1.129 192.168.1.129 25 255.255.255.255 255.255.255.255 10.8.0.6 2 1 255.255.255.255 255.255.255.255 10.8.0.6 10.8.0.6 1 255.255.255.255 255.255.255.255 192.168.1.129 192.168.1.129 1 Default Gateway: 192.168.1.1 =========================================================================== Persistent Routes: None

  Read the article

• Hundreds of unknown entries in Linux logwatch

  - by Saif Bechan

  I have a dedicated server which runs centos. Today i got an email from loginwatch on my server with hundreds of lines of 'errors'. I don't really know what they are becasue i am fairly new at this. The lines are in a few sections, I will display the first 10 of all of them, i hope someone can help me fix these problems. --------------------- Named Begin ------------------------ **Unmatched Entries** client 216.146.46.136 notify question section contains no SOA: 8 Time(s) client 92.114.98.10 query (cache) 'adobe.com/A/IN' denied: 4 Time(s) network unreachable resolving '11.254.75.75.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:13c7:7002:3000::11#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:500:13::c7d4:35#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:500:2e::1#53: 2 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:610:240:0:53::193#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:610:240:0:53::3#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:660:3006:1::1:1#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:6b0:7::2#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:dc0:1:0:4777::140#53: 1 Time(s) network unreachable resolving '136.176.97.93.in-addr.arpa/PTR/IN': 2001:dc0:2001:a:4608::59#53: 1 Time(s) network unreachable resolving '146.250.19.67.in-addr.arpa/PTR/IN': 2001:5a0:10::2#53: 1 Time(s) network unreachable resolving '149.207.106.87.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) network unreachable resolving '178.62.24.195.in-addr.arpa/PTR/IN': 2001:7fd::1#53: 1 Time(s) this goes on for hundreds of lines with all different domain names. --------------------- pam_unix Begin ------------------------ Failed logins from: 78.86.126.211 (78-86-126-211.zone2.bethere.co.uk): 111 times 93.97.176.136 (93-97-176-136.dsl.cnl.uk.net): 113 times 121.14.145.32: 136 times 190.152.69.5: 248 times 209.160.72.15: 572 times 210.26.48.35: 2 times 212.235.111.224 (DSL212-235-111-224.bb.netvision.net.il): 140 times 218.206.25.29: 140 times Illegal users from: 78.86.126.211 (78-86-126-211.zone2.bethere.co.uk): 2665 times 93.97.176.136 (93-97-176-136.dsl.cnl.uk.net): 2539 times 121.14.145.32: 116 times 190.152.69.5: 34 times 209.160.72.15: 324 times 218.206.25.29: 8051 times proftpd: Unknown Entries: session opened for user cent_ftp by (uid=0): 15 Time(s) session closed for user cent_ftp: 14 Time(s) sshd: Authentication Failures: unknown (218.206.25.29): 8051 Time(s) unknown (78-86-126-211.zone2.bethere.co.uk): 2665 Time(s) unknown (93.97.176.136): 2539 Time(s) root (209.160.72.15): 558 Time(s) unknown (209.160.72.15): 324 Time(s) root (190.152.69.5): 246 Time(s) unknown (121.14.145.32): 116 Time(s) root (121.14.145.32): 106 Time(s) root (dsl212-235-111-224.bb.netvision.net.il): 70 Time(s) root (93.97.176.136): 44 Time(s) root (78-86-126-211.zone2.bethere.co.uk): 37 Time(s) unknown (190.152.69.5): 34 Time(s) mysql (121.14.145.32): 30 Time(s) nobody (218.206.25.29): 26 Time(s) mail (218.206.25.29): 24 Time(s) news (218.206.25.29): 24 Time(s) root (218.206.25.29): 24 Time(s) --------------------- SSHD Begin ------------------------ **Unmatched Entries** pam_succeed_if(sshd:auth): error retrieving information about user tavi : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user pam : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user konchog : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user stavrum : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user rachel : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user affiliates : 24 time(s) pam_succeed_if(sshd:auth): error retrieving information about user nen : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user cobra : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user pass : 7 time(s) pam_succeed_if(sshd:auth): error retrieving information about user hacer : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user chung : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user zainee : 1 time(s) pam_succeed_if(sshd:auth): error retrieving information about user radu : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user alka : 4 time(s) pam_succeed_if(sshd:auth): error retrieving information about user albert : 5 time(s) pam_succeed_if(sshd:auth): error retrieving information about user turcia : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user cordell : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user silver : 2 time(s) pam_succeed_if(sshd:auth): error retrieving information about user dragon : 3 time(s) If someone wants to see the whole log i can upload it somewhere. Am i being hacked, what is this all?? I hope someone can help me, this does not look good at all.

  Read the article

• Weird networking problem ( Linksys, Windows 7 )

  - by Rohit Nair

  Okay it's a bit tough to figure out where to start from, but here is the basic summary of the issue: During general internet usage, there are times when any attempt to visit a website stalls at "Waiting for somedomain.com". This problem occurs in Firefox, IE and Chrome. No website will load, INCLUDING the router configuration page at 192.168.1.1. Curiously, ping works fine, and other network apps such as MSN Messenger continue to work and I can send and receive messages. Disconnecting and reconnecting to the wireless network seems to fix the problem for a bit, but there are times when it relapses into not loading after every 2-3 http requests. Restarting the router seems to fix the issue, but it can crop up hours or days later. I have a CCNA cert and I know my way around the Windows family of operating systems, so I'm going to list all the things I've tried here. Other computers on the network seem to suffer the same problem, which makes me think it might be a specific problem with something in Win7. The random nature of this issue makes it a bit difficult to confirm, but I can definitely say that I have experienced this on the following systems: Windows 7 64-bit on my desktop Windows Vista 32-bit on my desktop ( the desktop has 2 wireless NICs and the problem existed on both ) Windows Vista 32-bit on my laptop ( both with wireless and wired ) Windows XP SP3 on another laptop ( both wireless and wired ) Using Wireshark to sniff packets seemed to indicate that although HTTP requests were being SENT out, no packets were coming in to respond to the HTTP request. However, other network apps continued to work i.e I would still receive IMs on Windows Live Messenger. Disabling IPV6 had no effect. Updating router firmware to the latest stock firmware by Linksys had no effect. Switching to dd-wrt firmware had no effect. By "no effect" I mean that although the restart required by firmware updates fixed the problem at the time, it still came back. A couple of weeks back, after a LOT of googling and flipping of various options, I figured it might be a case of router slowdown ( http://www.dd-wrt.com/wiki/index.php/Router%5FSlowdown ) caused by the fact that I occasionally run a torrent client. I tried changing the configuration as suggested in that router slowdown link, and restarted the router. However I have not run the torrent client for 12 days now, and yet I still randomly experience this problem. Currently the computer I am using is running Windows 7 64-bit. I would just like to reiterate some of the reasons that I was confused by the issue. Even the router config page at 192.168.1.1 would not load, indicating that it's not a problem with the WAN link, but probably a router issue or a local computer issue. For some reason, disconnecting and reconnecting to the wireless network immediately seems to fix the problem. Updating the router firmware, even switching to open source firmware did nothing. So it seemed to be a computer issue. On the other hand, I have not seen any mass outrage of people having networking problems with Windows 7 and Linksys routers, especially a problem of this sort, and I have tweaked every network setting I could think of. Although HTTP seems to have trouble, ping works fine, DNS lookups work fine, other networking apps work fine. However if I disconnect from Windows Live Messenger and try to reconnect, it fails to reconnect. So although it could receive data over the existing TCP/IP connection, trying to start a new one failed? Does anyone have any further ideas on debugging or fixing this issue? I am reasonably certain there are no viruses or other malicious apps on my network, and I am also reasonably certain that nobody is accessing my router without my consent. Router: Linksys WRT54G2 1.0 running dd-wrt firmware Wireless Card: Alfa AWUS036H OS: Windows 7 64-bit EDIT: I tried switching to a clean wireless channel free from interference, but the problem still persisted. I tried connecting directly with a cable, but the problem still persisted. Signed A very confused and bewildered geek whose knowledge seems to be useless in the face of this frustrating network issue.

  Read the article

• PHP crashing (seg-fault) under mod_fcgi, apache

  - by Andras Gyomrey

  I've been programming a site using: Zend Framework 1.11.5 (complete MVC) PHP 5.3.6 Apache 2.2.19 CentOS 5.6 i686 virtuozzo on vps cPanel WHM 11.30.1 (build 4) Mysql 5.1.56-log Mysqli API 5.1.56 The issue started here http://stackoverflow.com/questions/6769515/php-programming-seg-fault. In brief, php is giving me random segmentation-faults. [Wed Jul 20 17:45:34 2011] [error] mod_fcgid: process /usr/local/cpanel/cgi-sys/php5(11562) exit(communication error), get unexpected signal 11 [Wed Jul 20 17:45:34 2011] [warn] [client 190.78.208.30] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Wed Jul 20 17:45:34 2011] [error] [client 190.78.208.30] Premature end of script headers: index.php About extensions. When i compile php with "--enable-debug" flag, i have to disable this line: zend_extension="/usr/local/IonCube/ioncube_loader_lin_5.3.so" Otherwise, the server doesn't accept requests and i get a "The connection with the server was reset". It is possible that i have to disable eaccelerator too because of the same reason. I still don't get why apache gets running it some times and some others not: extension="eaccelerator.so" Anyway, after i get httpd running, seg-faults can occurr randomly. If i don't compile php with "--enable-debug" flag, i can get DETERMINISTICALLY a php crash: <?php class Admin_DbController extends Controller_BaseController { public function updateSqlDefinitionsAction() { $db = Zend_Registry::get('db'); $row = $db->fetchRow("SHOW CREATE TABLE 222AFI"); } } ?> BUT if i compile php with "--enable-debug" flag, it's really hard to get this error. I must add some complexity to make it crash. I have to be doing many paralell requests for a few seconds to get a crash: <?php class Admin_DbController extends Controller_BaseController { public function updateSqlDefinitionsAction() { $db = Zend_Registry::get('db'); $tableList = $db->listTables(); foreach ($tableList as $tableName){ $row = $db->fetchRow("SHOW CREATE TABLE " . $db->quoteIdentifier($tableName)); file_put_contents( DB_DEFINITIONS_PATH . '/' . $tableName . '.sql', $row['Create Table'] . ';' ); } } } ?> Please notice this is the same script, but creating DDL for all tables in database rather than for one. It seems that if php is heavy loaded (with extensions and me doing many paralell requests) it's when i get php to crash. About starting httpd with "-X": i've tried. The thing is, it is already hard to make php crash with --enable-debug. With "-X" option (which only enables one child process) i can't do parallel requests. So i haven't been able to create to proper debug backtrace: https://bugs.php.net/bugs-generating-backtrace.php My concrete question is, what do i do to get a coredump? root@GWT4 [~]# httpd -V Server version: Apache/2.2.19 (Unix) Server built: Jul 20 2011 19:18:58 Cpanel::Easy::Apache v3.4.2 rev9999 Server's Module Magic Number: 20051115:28 Server loaded: APR 1.4.5, APR-Util 1.3.12 Compiled using: APR 1.4.5, APR-Util 1.3.12 Architecture: 32-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/usr/local/apache" -D SUEXEC_BIN="/usr/local/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf"

  Read the article

• Ubuntu 9.10 and Squid 2.7 Transparent Proxy TCP_DENIED

  - by user38400

  Hi, We've spent the last two days trying to get squid 2.7 to work with ubuntu 9.10. The computer running ubuntu has two network interfaces: eth0 and eth1 with dhcp running on eth1. Both interfaces have static ip's, eth0 is connected to the Internet and eth1 is connected to our LAN. We have followed literally dozens of different tutorials with no success. The tutorial here was the last one we did that actually got us some sort of results: http://www.basicconfig.com/linuxnetwork/setup_ubuntu_squid_proxy_server_beginner_guide. When we try to access a site like seriouswheels.com from the LAN we get the following message on the client machine: ERROR The requested URL could not be retrieved Invalid Request error was encountered while trying to process the request: GET / HTTP/1.1 Host: www.seriouswheels.com Connection: keep-alive User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US) AppleWebKit/532.9 (KHTML, like Gecko) Chrome/5.0.307.11 Safari/532.9 Cache-Control: max-age=0 Accept: application/xml,application/xhtml+xml,text/html;q=0.9,text/plain;q=0.8,image/png,/;q=0.5 Accept-Encoding: gzip,deflate,sdch Cookie: __utmz=88947353.1269218405.1.1.utmccn=(direct)|utmcsr=(direct)|utmcmd=(none); __qca=P0-1052556952-1269218405250; __utma=88947353.1027590811.1269218405.1269218405.1269218405.1; __qseg=Q_D Accept-Language: en-US,en;q=0.8 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Some possible problems are: Missing or unknown request method. Missing URL. Missing HTTP Identifier (HTTP/1.0). Request is too large. Content-Length missing for POST or PUT requests. Illegal character in hostname; underscores are not allowed. Your cache administrator is webmaster. Below are all the configuration files: /etc/squid/squid.conf, /etc/network/if-up.d/00-firewall, /etc/network/interfaces, /var/log/squid/access.log. Something somewhere is wrong but we cannot figure out where. Our end goal for all of this is the superimpose content onto every page that a client requests on the LAN. We've been told that squid is the way to do this but at this point in the game we are just trying to get squid setup correctly as our proxy. Thanks in advance. squid.conf acl all src all acl manager proto cache_object acl localhost src 127.0.0.1/32 acl to_localhost dst 127.0.0.0/8 acl localnet src 192.168.0.0/24 acl SSL_ports port 443 # https acl SSL_ports port 563 # snews acl SSL_ports port 873 # rsync acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl Safe_ports port 631 # cups acl Safe_ports port 873 # rsync acl Safe_ports port 901 # SWAT acl purge method PURGE acl CONNECT method CONNECT http_access allow manager localhost http_access deny manager http_access allow purge localhost http_access deny purge http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow localhost http_access allow localnet http_access deny all icp_access allow localnet icp_access deny all http_port 3128 hierarchy_stoplist cgi-bin ? cache_dir ufs /var/spool/squid/cache1 1000 16 256 access_log /var/log/squid/access.log squid refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern (Release|Package(.gz)*)$ 0 20% 2880 refresh_pattern . 0 20% 4320 acl shoutcast rep_header X-HTTP09-First-Line ^ICY.[0-9] upgrade_http0.9 deny shoutcast acl apache rep_header Server ^Apache broken_vary_encoding allow apache extension_methods REPORT MERGE MKACTIVITY CHECKOUT cache_mgr webmaster cache_effective_user proxy cache_effective_group proxy hosts_file /etc/hosts coredump_dir /var/spool/squid access.log 1269243042.740 0 192.168.1.11 TCP_DENIED/400 2576 GET NONE:// - NONE/- text/html 00-firewall iptables -F iptables -t nat -F iptables -t mangle -F iptables -X echo 1 | tee /proc/sys/net/ipv4/ip_forward iptables -t nat -A POSTROUTING -j MASQUERADE iptables -t nat -A PREROUTING -p tcp --dport 80 -j REDIRECT --to-port 3128 networking auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 142.104.109.179 netmask 255.255.224.0 gateway 142.104.127.254 auto eth1 iface eth1 inet static address 192.168.1.100 netmask 255.255.255.0

  Read the article

• Hosting a subversion working copy in an remote WebDAV folder

  - by Daniel Baulig

  This might be a bit awkward, but I'll try to explain what I am trying to achieve and what problems I encountered. First of all: whats this about? I am currently trying to set up a distributed working enviroment for developing a web page. My plan was to setup a SVN repository for version control, a live server where the actual live page ist hosted and a development server where I can work on the page. To ease things I intended to not have a local copy of the project on my disk, but to actually work directy on the files, that the development server hosts. For that I setup a WebDAV directory, under devserver.com/workspace, that actually mapped to files served under devserver.com/. So I could connect to devserver.com/workspace, change something and view the results live at devserver.com/. So far this worked perfectly. The next step was to create a SVN repository that would take care of my version control. I intended to be able to checkin to the reposiroty from my development server and at any time, with a small shell script, deploy any revision from the svn to the live server by checking out a copy of the revision into the live server directories. The second part, checking out into the live server, also worked perfectly. The first part though is where problems arose: My workstation is a Windows 7 machine. I connected to the WebDAV share using Windows built-in WebDAV support, which worked quite well. I can create, move, delete, edit, whatever files on my WebDAV share from my Windows machine perfectly. The next step was to checkout a working copy from the SVN (actually hosted at devserver.com/subversion/) into the WebDAV share. In the first try I used the Eclipse plugin subversive. The actual checkout worked fine and I can update and commit stuff to the repository, however, I cannot add any files to the ignore list. It always brings me an error. So I tried the same thing with a complete fresh repository using TortoiseSVN - and again it failed with the same errors. Here is what it says when trying to add files to svnignore: Some of selected resources were not added to ignore. svn: Cannot rename file '\\devserver.com@SSL\DavWWWRoot\workspace\.svn\tmp\dir-props.66fd8936-2701-0010-bb76-472f0b56a5d1.tmp' to '\\devserver.com@SSL\DavWWWRoot\workspace\.svn\tmp\dir-props' This is what apache2 tells me, when I try to add a file to svnignore: [Sun Mar 07 03:54:19 2010] [error] [client xxx.xxx.xxx.xxx] Negotiation: discovered file(s) matching request: /var/www/devserver.com/.svn/tmp/dir-props (None could be negotiated). [Sun Mar 07 03:54:31 2010] [error] [client xxx.xxx.xxx.xxx] (20)Not a directory: The URL contains extraneous path components. The resource could not be identified. [400, #0] Actually both messages are repeated several times. The first one occurs first and is repeated about 5 times and the second comes there after and is repeated propably more than 20 times. If I create a regular file, delete, rename or modify it none of those messages appear in my error.log While writing this question now I was able to add fils to svnignore using TortoiseSVN. However, after that, Eclipse would not let me commit anymore. The error that used to pop up when adding files to svnignore now also shows up while commiting. While searching the web I found some people having this same message appearing because they had files only different in upper- / lower-case naming. I checked my repository and did not find such files. I also read somewhere about people having troubles with WebDAV and file locking, because WebDAV's file locking capabilities seem to be very limited. At some stage I got errors telling me my repository was locked and thus the operations could not be completed. This error though did not appear anymore, since I setup a completely fresh repository and working copy. I would really appreciate any help anyone can provide me in fixing this problem! If there are any more questions feel free to ask. I know this is a somewhat unusual setup. Best regards, Daniel

  Read the article

• Unauthorized Access Exception using Web Deploy to Site when the site root is a UNC path

  - by Peter LaComb Jr.

  I am trying to use Web Deploy to deploy a site where the Site is rooted on a UNC path instead of a local drive. This is because I want to have a shared configuration, and have all servers point to the same UNC for content. That would allow me to deploy to one server and have all servers updated at the same time. I've created a share with everyone and users read/write. The NTFS permissions have the ID of the appDomain account as full control, and that is the same account that is configured as the specific user in Management Service Delegation. I can log on to the destination server as that ID, access the share and create/delete files. However, I'm getting the following exception in my Microsoft Web Deploy log on the destination server: User: Client IP: 192.168.62.174 Content-Type: application/msdeploy Version: 9.0.0.0 MSDeploy.VersionMin: 7.1.600.0 MSDeploy.VersionMax: 9.0.1631.0 MSDeploy.Method: Sync MSDeploy.RequestId: c060c823-cdb4-4abe-8294-5ffbdc327d2e MSDeploy.RequestCulture: en-US MSDeploy.RequestUICulture: en-US ServerVersion: 9.0.1631.0 Skip: objectName="^configProtectedData$" Provider: auto, Path: A tracing deployment agent exception occurred that was propagated to the client. Request ID 'c060c823-cdb4-4abe-8294-5ffbdc327d2e'. Request Timestamp: '8/23/2012 11:01:56 AM'. Error Details: ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER Microsoft.Web.Deployment.DeploymentDetailedUnauthorizedAccessException: Unable to perform the operation ("Create Directory") for the specified directory ("\someserver.mydomain.local\sharename\sitename\applicationName"). This can occur if the server administrator has not authorized this operation for the user credentials you are using. Learn more at: http://go.microsoft.com/fwlink/?LinkId=221672#ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER. --- Microsoft.Web.Deployment.DeploymentException: The error code was 0x80070005. --- System.UnauthorizedAccessException: Access to the path '\someserver.mydomain.local\sharename\sitename\applicationName' is denied. at Microsoft.Web.Deployment.NativeMethods.RaiseIOExceptionFromErrorCode(Win32ErrorCode errorCode, String maybeFullPath) at Microsoft.Web.Deployment.DirectoryEx.CreateDirectory(String path) at Microsoft.Web.Deployment.DirPathProviderBase.CreateDirectory(String fullPath, DeploymentObject source) at Microsoft.Web.Deployment.DirPathProviderBase.Add(DeploymentObject source, Boolean whatIf) --- End of inner exception stack trace --- --- End of inner exception stack trace --- at Microsoft.Web.Deployment.FilePathProviderBase.HandleKnownRetryableExceptions(DeploymentBaseContext baseContext, Int32[] errorsToIgnore, Exception e, String path, String operation) at Microsoft.Web.Deployment.DirPathProviderBase.Add(DeploymentObject source, Boolean whatIf) at Microsoft.Web.Deployment.DeploymentObject.Add(DeploymentObject source, DeploymentSyncContext syncContext) at Microsoft.Web.Deployment.DeploymentSyncContext.HandleAdd(DeploymentObject destObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentSyncContext.HandleUpdate(DeploymentObject destObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenNoOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenNoOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.ProcessSync(DeploymentObject destinationObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentObject.SyncToInternal(DeploymentObject destObject, DeploymentSyncOptions syncOptions, PayloadTable payloadTable, ContentRootTable contentRootTable, Nullable1 syncPassId) at Microsoft.Web.Deployment.DeploymentAgent.HandleSync(DeploymentAgentAsyncData asyncData, Nullable1 passId) at Microsoft.Web.Deployment.DeploymentAgent.HandleRequestWorker(DeploymentAgentAsyncData asyncData) at Microsoft.Web.Deployment.DeploymentAgent.HandleRequest(DeploymentAgentAsyncData asyncData) This is shown as the following on the console of the machine where I run the deployment: C:\Users\PLaComb"C:\Program Files (x86)\IIS\Microsoft Web Deploy V3\msdeploy.exe" -source:package='C:\Packages\Deployments\applicationName.zip' -dest:auto,computerName='https://SERVERNAME:8172/msdeploy.axd',includeAcls='True' -verb:sync -disableLink:AppPoolExtension -disableLink:ContentExtension -disableLink:CertificateExtension -setParamFile:"C:\Packages\Deployments\applicationName.SetParameters.xml" -allowUntrusted Info: Using ID 'c060c823-cdb4-4abe-8294-5ffbdc327d2e' for connections to the remote server. Info: Adding sitemanifest (sitemanifest). Info: Adding virtual path (JMS/admin) Info: Adding directory (JMS/admin). Error Code: ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER More Information: Unable to perform the operation ("Create Directory") for the specified directory ("\someserver.mydomain.local\sharename\sitename\applicationName"). This can occur if the server administrator has not authorized this operation for the user credentials you are using. Learn more at: http://go.microsoft.com/fwlink/?LinkId=221672#ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER. Error: The error code was 0x80070005. Error: Access to the path '\someserver.mydomain.local\sharename\sitename\applicationName' is denied. Error count: 1.

  Read the article

• RHEL - NFS4: Mounted/Exported as rw, user write permission denied

  - by brendanmac

  Hello, I have nfs4 configured between a RHEL 5.3 server (charlie) and a RHEL 5.4 client (simcom1). The machines are configured to authenticate users via kerberos by a Windows Server 2008 active directory machine called "alpha." Alpha also serves as a dns and dhcp machine for the local network. I notice that when a user logs in to a RHEL machine for the first time they are issued a unique uid to that machine; The first user to log on gets 10001. So, what I see is that users between simcom1 and charlie have different UIDs. When a user does an 'ls -la' command from within an nfs4 mount I would have thought that the usernames in the owner column would indicate 'nobody' or at least the wrong user name - since UIDs are different between the machines for each user, and not all users have logged into each machine. However, the simcom1 is able to resolve usernames in an 'ls -la' executed on files residing on charlie via nfs4 correctly. Most troubling is that users are unable to write to files across the nfs mount. The server, charlie, has the root directory exported as rw. The client, simcom1, mounts the export as rw. My configurations are shown below. My question is, how do I configure the RHEL machines to allow users to write files across nfs4 that is already mounted as read/write? [root@charlie ~]# more /etc/exports / 10.100.0.0/16(rw,no_root_squash,fsid=0) [root@charlie ~]#cat /etc/sysconfig/nfs # # Define which protocol versions mountd # will advertise. The values are "no" or "yes" # with yes being the default #MOUNTD_NFS_V1="no" #MOUNTD_NFS_V2="no" #MOUNTD_NFS_V3="no" # # # Path to remote quota server. See rquotad(8) #RQUOTAD="/usr/sbin/rpc.rquotad" # Port rquotad should listen on. #RQUOTAD_PORT=875 # Optinal options passed to rquotad #RPCRQUOTADOPTS="" # # # TCP port rpc.lockd should listen on. #LOCKD_TCPPORT=32803 # UDP port rpc.lockd should listen on. #LOCKD_UDPPORT=32769 # # # Optional arguments passed to rpc.nfsd. See rpc.nfsd(8) # Turn off v2 and v3 protocol support #RPCNFSDARGS="-N 2 -N 3" # Turn off v4 protocol support #RPCNFSDARGS="-N 4" # Number of nfs server processes to be started. # The default is 8. RPCNFSDCOUNT=8 # Stop the nfsd module from being pre-loaded #NFSD_MODULE="noload" # # # Optional arguments passed to rpc.mountd. See rpc.mountd(8) #STATDARG="" #RPCMOUNTDOPTS="" # Port rpc.mountd should listen on. #MOUNTD_PORT=892 # # # Optional arguments passed to rpc.statd. See rpc.statd(8) #RPCIDMAPDARGS="" # # Set to turn on Secure NFS mounts. SECURE_NFS="no" # Optional arguments passed to rpc.gssd. See rpc.gssd(8) #RPCGSSDARGS="-vvv" # Optional arguments passed to rpc.svcgssd. See rpc.svcgssd(8) #RPCSVCGSSDARGS="-vvv" # Don't load security modules in to the kernel #SECURE_NFS_MODS="noload" # # Don't load sunrpc module. #RPCMTAB="noload" # [root@simcom1 ~]# cat /etc/fstab --start snip-- charlie:/home /usr/local/dev/charlie nfs4 rw,nosuid, 0 0 --end snip-- [brendanmac@simcom1 /usr/local/dev/charlie/brendanmac]# touch file touch: cannot touch 'file': Permission denied [brendanmac@simcom1 /usr/local/dev/charlie/brendanmac]# su Password: [root@simcom1 /usr/local/dev/charlie/brendanmac]# touch file [root@simcom1 /usr/local/dev/charlie/brendanmac]# ls -la file -rw------- 1 root root 0 May 26 10:43 file Thank you for your assistance, Brendan

  Read the article

• proftpd, dynamic IP, and filezilla: port troubles

  - by Yami

  The basic setup: Two computers, one running proftpd, one attempting to connect via filezilla. Both linux (xubuntu on the server, kubuntu on the client). Both are at the moment behind a router on a residential (read: dynamic IP) connection; the client is a laptop I plan to take away from the home network, so I'll need this to work externally. I have my router set up to allow specific ports forwarded to each machine and, where possible, have plugged in those numbers into proftpd (via gadmin, double-checking the config file) and filezilla. Attempting to connect via active mode using the internal IP works: Status: Connecting to 192.168.1.139:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 192,168,1,52,153,140 Response: 200 PORT command successful Command: LIST Response: 150 Opening ASCII mode data connection for file list Response: 226 Transfer complete Status: Directory listing successful Attempting to connect via the domain name, however, leads to issues; in active mode, the PORT is the last command to be received according to the server's logs, and in passive mode, it's the PASV command. This leads me to believe I'm being redirected to a bad port? Active Sample: Status: Resolving address of <url> Status: Connecting to <ip:port> Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 174,111,127,27,153,139 Response: 200 PORT command successful Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing Passive sample: Status: Resolving address of ftp.bonsaiwebdesigns.com Status: Connecting to 174.111.127.27:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER yamikuronue Response: 331 Password required for yamikuronue Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (64,95,64,197,101,88). Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing In both cases, the log file ends at "PORT" or "PASV" - there's no record of ever receiving a "LIST" command. Just above that I can see the attempt to connect actively via the internal IP, which does indeed include a LIST command. My config file includes "PassivePorts 20001-26999", which are the port forwards I set up for the ftp server, and "Port 8085", which is also forwarded to the same machine. I also have a MasqueradeAddress set up to prevent it from reporting its internal IP, which was an earlier issue I had. I think what I'm asking is, is there another setting someplace I have to change to get this setup to work?

  Read the article

• Troubleshooting PHP email sending?

  - by darkAsPitch

  I created a website that occasionally emails users when they register/change their password/etc. Every other person however cannot or does not receive the emails. They are telling me that they are not even hitting their spam folders. I don't know a ton about MX records or email sending, but when I "Edit DNS Zone" for this domain in particular there is 1 MX record listed there. How do you go about troubleshooting botched PHP mail actions? UPDATE: Here is my super-simple php mailing code: $subject = "Subject Here"; $message = "Emails Message"; $to = $verified_user_data["email_address"]; $headers = "From: [email protected]\r\n" . "Reply-To: [email protected]\r\n" . "X-Mailer: PHP/" . phpversion(); //returns true on success, false on failure $email_result = mail($to, $subject, $message, $headers); re: "are you saying that some do and some do not?" @ Jacob Yes, basically. I send the emails containing the user's login username/password using similar code above. And I sell to fairly tech-savvy people. About 50% of the time, my customers claim they cannot find their welcome emails in their inbox OR in their spam box. It's as if it never arrived. I have the largest problem with Yahoo email addresses accepting my emails or so it seems. re: "The MX record at your end doesn't factor in, although the SPF record (or lack of it) will. How much access and control do you have on the server itself?" @ John Gardeniers I rent a dedicated server from Codero. Running CentOS 5, WHM + cPanel. I have full root access to the entire thing. Don't know much about MX records and/or SPF records. I just want the PHP mail function to work. It doesn't say much about that on the php mail function's help page. re: "What are you using for the SMTP server?" @ JonLim No idea. I use the code above when I need to fire off an email to a loyal customer, and that's it. Do I need to be worrying about SMTP servers? re: "Could be many, many things. Can you describe how you're sending mail in your code? i.e. are you relaying off of another mail server somewhere, using the local sendmail or postfix? Any consistency in domains that can/cannot receive email? Do you have a PTR record setup from the IP address that you're sending mail out as? What about SPF records?" @ gravyface I just described my simple code above! I believe I have been having the most trouble with Yahoo domains, however "independent" domains (probably running spamassasin) ex. [email protected] as opposed to [email protected] seem to give a lot of trouble as well. I do not know if I have a PTR record setup from the IP address I'm sending my mail from. It's probably the same IP address that I setup my domain on, because I didn't do anything extra special. No idea about SPF records either, where can I go to create one? Side Note: It's a crying shame what havoc the spammers have brought upon our beloved email system.

  Read the article

• Replicate between mysql 5.0.xx community and enterprise edition over ssh

  - by Arlukin

  I'm trying to setup a mysql replication over an SSH tunnel. The odd thing about this setup is that I have one master with mysql 5.0.60sp1-enterprise-gpl-log and one slave with mysql 5.0.67-community-log. Could it be so that it's not possible to replicate between community and enterprise edition? As you can see in my log below, it's possible to login on the remote server with the mysql client. But the replication get "Can't connect to MySQL server on '127.0.0.1' (13)" Is it any log file I have forgotten to look in, to get more info? [root@mysql1-av ~]# mysql -uroot -p Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 73 Server version: 5.0.67-community-log MySQL Community Edition (GPL) Type 'help;' or '\h' for help. Type '\c' to clear the buffer. The version of the slave mysql [root@mysql1-av ~]# autossh -f -M 20001 -L 3307:10.200.200.200:3306 [email protected] -N [root@mysql1-av ~]# mysql -h127.0.0.1 --port 3307 -uroot -p Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 5189 Server version: 5.0.60sp1-enterprise-gpl-log MySQL Enterprise Server (GPL) Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> Aborted Login to the master mysql with the mysql client over the ssh tunnel. [root@mysql1-av ~]# mysql -uroot -p Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 75 Server version: 5.0.67-community-log MySQL Community Edition (GPL) Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> change master to master_host='127.0.0.1', MASTER_PORT=3307, master_user='xxxx', master_password='xxxx', master_log_file='bin.000001'; Query OK, 0 rows affected (0.00 sec) mysql> start slave; Query OK, 0 rows affected (0.00 sec) mysql> show slave status \G *************************** 1. row *************************** Slave_IO_State: Connecting to master Master_Host: 127.0.0.1 Master_User: replNSG Master_Port: 3307 Connect_Retry: 60 Master_Log_File: bin.000001 Read_Master_Log_Pos: 4 Relay_Log_File: relay.000001 Relay_Log_Pos: 98 Relay_Master_Log_File: bin.000001 Slave_IO_Running: No Slave_SQL_Running: Yes Replicate_Do_DB: Replicate_Ignore_DB: Replicate_Do_Table: Replicate_Ignore_Table: Replicate_Wild_Do_Table: Replicate_Wild_Ignore_Table: Last_Errno: 0 Last_Error: Skip_Counter: 0 Exec_Master_Log_Pos: 4 Relay_Log_Space: 98 Until_Condition: None Until_Log_File: Until_Log_Pos: 0 Master_SSL_Allowed: No Master_SSL_CA_File: Master_SSL_CA_Path: Master_SSL_Cert: Master_SSL_Cipher: Master_SSL_Key: Seconds_Behind_Master: NULL 1 row in set (0.00 sec) Start the replication, but it breaks on IO. [root@mysql1-av ~]# tail /var/log/mysqld.log 120921 22:17:59 [Note] Slave I/O thread killed while connecting to master 120921 22:17:59 [Note] Slave I/O thread exiting, read up to log 'bin.000001', position 4 120921 22:17:59 [Note] Error reading relay log event: slave SQL thread was killed 120921 22:29:36 [Note] Slave SQL thread initialized, starting replication in log 'bin.000001' at position 4, relay log '/var/lib/mysql/relay.000001' position: 4 120921 22:29:36 [ERROR] Slave I/O thread: error connecting to master '[email protected]:3307': Error: 'Can't connect to MySQL server on '127.0.0.1' (13)' errno: 2003 retry-time: 60 retries: 86400 Because it can't connect to the master server.

  Read the article

• Coda 2 and SCP uploading files with the wrong permission

  - by Tom Black

  Currently I have a basic Ubuntu server running a website. The website is for a few students learning HTML/PHP and each student has their own account with a symbolic link to the shared website folder. Since the students are working on the website together, each user needs to be able to modify all the files (index.html for example). So I created a Webdev group containing all of the students with the default umask of 0002 set in their .bashrc (This allows newly created files to be 774). The shared folder is owned by the group Webdev with a chmod g+s so that new files/folders also belong to the group Webdev. The problem is that the students are using an IDE (Coda 2) and when they create a new file or folder using the IDE the file has the permissions of 644 on the server (not group writable). However when I make a new file through connecting with Cyberduck (SFTP client) the file permissions are 664 (as they should be). So I don't understand why Coda would be any different. However, after some trial and error I believe that Coda is first creating the file on local disk and then uploading that file to the server. On a mac by default a newly created file is 644. When the client uploads a file that's already 644 it stays 644 on the server side (umask is kind of useless in this situation). I've also tried creating ACL permissions for that folder but an uploaded file from my mac via SCP doesn't get the default ACL permissions. In Coda there is an option to change file permissions on a transfer. However this option seems to apply a chmod to all files being uploaded or saved. When one of students is modifying a file created by someone else when they try to upload the file or save it Coda tries to also do a chmod but fails because that user isn't the owner of the file. My current solution is using bindfs... I mount the shared web folder and bindfs sets permissions and group ownership of newly created files. However, bindfs seems to be a bit slow and I'm sure there is a better solution. Even if the students ditched Coda 2 and used Mac vim with scp the newly created files on the server would behave the same (644) which is default on the mac. Other options... 1) Either I teach the students to use (ssh/chmod) with their IDE to change their own file permissions when uploading. 2) I make all the students' Macs have the default umask of 0002 which would upload files with the right permissions. 3) Write a corn script to fix the file permissions every 5 to 15 minutes... (This option I think is the worst if students are working together at the same time). Is there any way that I could make all files that are uploaded via SCP have the default file permissions of 664 even though the uploaded file has a lower permission? (After hours of searching I don't think this is possible) I guess a corn script is my best option for novice users. How do web developers work together on larger sites? similar to this: http://serverfault.com/questions/283492/how-to-specify-file-permission-when-putting-a-file-using-openssh-sftp-command Also similar: http://serverfault.com/questions/395418/managing-linux-directory-permissions-sftp

  Read the article

< Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >