Search Results

Search found 18249 results on 730 pages for 'real world haskell'.

Page 548/730 | < Previous Page | 544 545 546 547 548 549 550 551 552 553 554 555  | Next Page >

• Server and Network Lag

  - by DanSpd

  At my home I have a server and my computer. Server has Windows Server 2008 Standart 64 bit installed and then my computer has Windows 7 64 bit installed. My home router is DIR-615 My server has a game server installed on it and basically total open connections on server are around 700. Once its around 700 server and then whole home network lags really badly. My internet connection is good and only around 600kb/s is being used out of 2mb/s (real download/upload speeds). So far I assume that my router has a connection limit and with server + my computer connections it peaks at around 1k and lags everything. Another assumption server lag comes from connection limit. On the internet I have read that standart version of server has connection limit of 700 + 10 reserved. I do not rmember where I found that information but it was on microsoft website. So I have two options. First is to upgrade my router to Netgear FVS318G-100 and second is to change connections limit on server. Any advices? Thank you

  Read the article

• ESXi Server with 12 physical cores maxed out with only 8 cores assigned in virtual machines

  - by Sam

  I have an ESXi 5 server running on a 2-processor, 12-core system with hyperthreading enabled. So: 12 physical cores, 24 logical ones. On this server are 4 Windows 7 VMs, each configured for 2 processors, each running VMware Tools. Looking at my stats in vSphere, my "core utilization" is constantly maxed out. Yes, these machines are working hard, but only 8 cores have been allocated. How is this possible? Should I look into reducing the processor count per machine as in this post: VMware ESX server? I checked to ensure that hardware virtualization is enabled in the BIOS of the machine (a DELL R410). I've also started reading up on configuration, but being a newbie there's a lot of material to catch up on. It also seems I should only bother with advanced settings and pools if I'm really pushing the load, and I don't think that I should be pushing it with so few VMs. I suspect that I have some basic, incorrect configuration setting, but it's also possible that I have some giant misconceptions about virtualization. Any pointers? EDIT: Given the responses I've gotten so far, it seems that this is a measurement problem and not a configuration problem, making this less critical. Perhaps the real question is: How does the core utilization of the server reach a higher percentage than all individual cores' core utilization, and given that this possibility makes the metric useless for overall server load, what is the best global metric for measuring CPU load on hyper-threaded systems?

  Read the article

• Apache reaching MaxClients and locking the server

  - by Rodrigo Sieiro

  Hi. I currently have an Apache2 server running with mpm-prefork and mod_php on a OpenVZ VPS with 512M real / 1024M burstable RAM (no swap). After running some tests, I found that the maximum process size Apache gets is 23M, so I've set MaxClients to 25 (23M x 25 = 575 MB, ok for me). I decided to run some load tests on my server, and the results left me puzzled. I'm using ab on my desktop machine requesting the main page from a wordpress blog. When I run ab with 24 concurrent connections, everything seems fine. Sure, CPU goes up, free RAM goes down, and the result is about 2-3s response time per request. But if I run ab with 25 concurrent connections (my server limit), Apache just hangs after a couple of seconds. It starts processing the requests, then it stops responding, CPU goes back to 100% idle and ab times out. Apache log says it reached MaxClients. When this happens, Apache keeps itself locked up with 25 running processes (they're all in "W" if I check server status) and only after the TimeOut setting the processes start to die and the server starts responding again (in my case it's set to 45). My question: is that expected behaviour? Why Apache just dies when it reaches MaxClients? If it works with 24 connections, shouldn't it work with 25, just taking maybe more time to respond each request and queueing up the rest? It sounds kinda strange to me that any kid running ab can alone kill a webserver just by setting the concurrent connections to the servers MaxClients.

  Read the article

• Apache MaxClients reaching max and locking the server

  - by Rodrigo Sieiro

  Hi. I currently have an Apache2 server running with mpm-prefork and mod_php on a OpenVZ VPS with 512M real / 1024M burstable RAM (no swap). After running some tests, I found that the maximum process size Apache gets is 23M, so I've set MaxClients to 25 (23M x 25 = 575 MB, ok for me). I decided to run some load tests on my server, and the results left me puzzled. I'm using ab on my desktop machine requesting the main page from a wordpress blog. When I run ab with 24 concurrent connections, everything seems fine. Sure, CPU goes up, free RAM goes down, and the result is about 2-3s response time per request. But if I run ab with 25 concurrent connections (my server limit), Apache just hangs after a couple of seconds. It starts processing the requests, then it stops responding, CPU goes back to 100% idle and ab times out. Apache log says it reached MaxClients. When this happens, Apache keeps itself locked up with 25 running processes (they're all in "W" if I check server status) and only after the TimeOut setting the processes start to die and the server starts responding again (in my case it's set to 45). My question: is that expected behaviour? Why Apache just dies when it reaches MaxClients? If it works with 24 connections, shouldn't it work with 25, just taking maybe more time to respond each request and queueing up the rest? It sounds kinda strange to me that any kid running ab can alone kill a webserver just by setting the concurrent connections to the servers MaxClients.

  Read the article

• Accidently overwrote system.dbf - What now?

  - by Filip Ekberg

  I accidentally overwrote system.dbf in /usr/lib/oracle/xe/oradata/XE/system.dbf Well I did not actually do it accidentally, however I overwrote it because of other failures in the database. And when I try running the following: SQL> shutdown ORA-01109: database not open Database dismounted. ORACLE instance shut down. SQL> startup ORACLE instance started. Total System Global Area 289406976 bytes Fixed Size 1258488 bytes Variable Size 92277768 bytes Database Buffers 192937984 bytes Redo Buffers 2932736 bytes Database mounted. ORA-01589: must use RESETLOGS or NORESETLOGS option for database open Now I want to try to Recover the database because starting it in mounted or standard surely doesn't work. SQL> recover database using backup controlfile; ORA-00283: recovery session canceled due to errors ORA-01110: data file 1: '/usr/lib/oracle/xe/oradata/XE/system.dbf' ORA-01122: database file 1 failed verification check ORA-01110: data file 1: '/usr/lib/oracle/xe/oradata/XE/system.dbf' ORA-01206: file is not part of this database - wrong database id How do I solve this? Is it even possible? My "real" problem was that I ran the /etc/init.d/oracle-xe configure and it overwrote my old configuration and probably removed passwords and such so my tables were gone, however I found the mytablespace.dbf so I hope that it is possible to recover? Please shed some light on this.

  Read the article

• NVidia ION and /dev/mapper/nvidia_... issues.

  - by Ritsaert Hornstra

  I have an NVidia ION board with 4 SATA ports and want to use that to run a Linux Server (CentOS 5.4). I first hooed up 3 HDs (that will be a RAID5 array) and a forth small boot HD. I first started to use the onboard RAID capability but that does not work correctly under Linux: the raid capacity is not a real RAID but uses lvm to define some arays. After setting the BIOS back to normal SATA mode and whiping the HDs, the first boot harddisk (/dev/sda) is seen as /dev/sda BEFORE mounting and after mounting as /dev/mapper/nvidia_. CentOS is unable to install on it (and grub is not installable on it either). So somehow the harddisk is still seen as if it belongs to some lvm volume. I tried to clean out the HD by issuing a few dd if=/dev/zero of=/dev/sda commands to wipe the starting cylinders and final cylinders but to no avail. Did anyone see this problem and did anyone find a solution? UPDATE When I create only a single ext3 partition on the first HD (/dev/mapper/nvidia_...) no LVM partitions are seen and I can boot from /dev/mapper/nvidia_.... Now the next step is to see how I can get rid of this folly.

  Read the article

• Is it possible to be a Linux professional studying on your own?

  - by Marc Jr

  I read economics at university(nothing to see with linux, isn't it? :P). I have some basic knowledge about booting process, Linux Kernel compiling from source and stuff like that. But of course I have still much to learn sometimes some errors appears and "voila" I am lost. I had: Ubuntu, Fedora, OpenSuse, Arch.. using Gentoo now. I'd like to know what you linux users, professionals, administrators... would think it is the best way to learn linux in a professional way. Is it worth studying it and passing the LPIC test enough to work in the linux world? or do I need going to IT uni? I've heard LFS is a good way of learning about linux, is that real? I've been thinking about getting to LFS learn about more deeply about the linux process and learning scripts. It is possible to do this way? if anyone has a tip or a good way of doing, maybe someone did it. Any tip is very welcome. Words from a person in love with linux. :D The best, Marc

  Read the article

• Is there a simple LDAP-to-HTTP gateway out there?

  - by larsks

  We have a local LDAP directory that provides basic contact information about our user community. We would like to integrate this into some third-party hosted services that allow us to implement widgets that run arbitrary Javascript. In order to connect Javascript to our LDAP directory, I would like to set up a simple LDAP-to-HTTP proxy that would accept HTTP GET requests, translate them into an appropriate LDAP query, and respond with directory information as JSON-encoded data. In an ideal world, something like this: GET /[email protected] Would get me something like this: { "cn": "Bob Person", "title": "System Administrator", "sn": "Person", "mail": "[email protected]", "telepehoneNumber": "617-555-1212", "givenName": "Bob" } (And this obviously assumes that the web application has locally configured information about what base DN to use, how to authenticate, etc). I guess I could write one...but surely something like this already exists? UPDATE The consensus seems to be that there isn't a pre-existing solution out there and that I should just get off my lazy derriere and write one. So I did, and it's here. It's not especially pretty, but it works for my prototyping and I figure maybe someone else will find it useful someday.

  Read the article

• Running Mathematica-5 remotely

  - by oxinabox.ucc.asn.au

  I have Mathematica 5 - a powerful CAS. I have a cheap netbook (running Windows XP), wich not only is too slow to run mathmatica on, I doubt it has the harddrive space. I do however have remote access to a number of very powerful computers, (most of wich run variose Linuxes, but one of which is Windows Server 2008, though I'ld rather not use this one*). Mostly over SSH but other protocols can be arraged for some, I'm sure. So I'ld like to install Mathematica onto one of these machine and then run it remotely. Either from the command line via Putty or via some other method. I glanced through the mathematical documentation and read something about using some MathLink program, which links the front end installed on my computer to a remote kernel. Anyone have any experience with this? I'm not sure if this belongs here or in SuperUser. At the moment, it's being tinkered with, and when the tinkering stops it'll likely be used to run multiple thin terms. As compared to the Linux machines: I have access to a dual 2.4 Xeon with 3GB RAM, which the rest of the world seems to have completely forgotten about (runs freeBSD!).

  Read the article

• How do I effectively use WinSCP on my GoDaddy Dedicated Hosting

  - by Scott

  After being told that Virtual Private Servers would not fit the scope of my project, I have timidly entered the world of dedicated hosting. Unfortunately, this is forcing me how to learn the basics of being a Linux server admin. GoDaddy has a master account for the server. When you use SSH, they want you to use "su" to switch to the root user. Thus far, I have been able to do everything I have needed to thus far via the command line as this root user. However, now I need to upload files to my server. I'm used to using WinSCP to upload files. I can use my general server account to view the files but when I try to drag or create files its says that I cannot because I do not have permission to do so. I have researched the WinSCP documentation and it seems that this "su" function is beyond the scope of the program. How am I to grant myself access to upload these files using SSH? Should I create a user with the proper permissions? I'm happy to do this but thus far I have not been able to make sense of what I have found online. I'm going to try and move forward but any help and/or insight is appreciated.

  Read the article

• D-LINK 2450U DSL router: Port forwarding forwading to the modem itself, not the specified IP

  - by axk

  I found a similar question but it has no satisfactory answers. I have a D-LINK 2540U DSL router. It has a basic port forwarding(under DNS - Virtual Servers) configuration in the administration panel where you specify: external port range, protocol, internal port range, server IP address and it is supposed to forward that port to that IP address. When I first set it up for a Real VNC connection it worked fine, just as I expected. Then I added a DynDNS configuration entry in the router's 'Dynamic DNS' section and added an additional SSH (22) forwarding rule. The SSH forwarding also worked fine (now with the dynamic hostname, but I suppose it doesn't make any difference as far as SSH is concerned). Then I removed the SSH rule and after that the VNC forwarding stopped working with the VNC client failing to connect (I have tried to connect with telnet and it also failed to connect, so it wasn't a VNC problem). After adding a rule for port 80 it turned out it would forward on port 80 though not to the specified server IP but to the modem itself. At least it is what it looks like, because it gives me the administration panel when I connect to my external IP (both using a browser and plain telnet in which case I can see that it is mini_hhtpd sitting on the port, which is obviously the modem's administration panel). Have anybody encountered a similar problem with port forwarding? I have tried to do a reset through the administration panel and to restore a backup of the settings made before I started playing with port forwarding, but it didn't help. Should I do a 'hard' reset with the button on the modem? Is it any different from the administration panel's reset (Restore default)?

  Read the article

• Any ideas out there as to how the data can be recovered from an SSD?

  - by ben

  A friend had some form of catastrophic failure on an HP mini 1000, unbootable. Of course there was data that wasn't backed up. I've removed the SSD and hooked it up to a ZIF 40 enclosure but can not seem to get the drive to be recognized in Windows 7. In Disk Management it displays as present, but uninitialized. Attempting to initialize it presents an error Virtual Disk Manager - "The device is not ready". There is scant information on MIE (the custom OS), so I'm not even sure what kind of file system I'm dealing with. In any case, if the filesystem is indeed some flavor other than FAT or NTFS, is this error consistent with that? Are there any creative ideas out there as to how the data can be recovered? Update: Thanks for all the suggestions! I hadn't even considered running a live cd. Unfortunately no luck with Ubuntu (live cd) or explore2fs. The zif connection seems ok (color coded green led for proper connect, orange for not). The drive can't be initialized and therefore can't be formatted, so I guess there may be some real damage. Probably needs to head to a specialist. Thanks again for the feedback, much appreciated.

  Read the article

• Making OpenSSL work on PHP Windows 2008 server with FastCGI

  - by KacieHouser

  I have been researching all day. Here is what I have done: In C:/PHP/php.ini and C:/PHP/php-cgi-fcgi.ini I have made the extension_dir = "C:/PHP/ext" I uncommented extension=php_openssl.dll I went to http://windows.php.net/download/ and got the thread safe version with the PHP 5.4 (5.4.8) version of DLL's In C:/PHP/ext I replaced the php_openssl.dll with the one I downloaded In System32 and SysWOW64 I added the following DLL's ssleay.dll libeay.dll I restarted the IIS server in the Server Manager under Web Server and stopped and started the World Wide Web Publishing Service That didn't work, so I tried same thing with the unthreaded versions. I still get: Fatal error: Call to undefined function ftp_ssl_connect() in C:\inetpub\wwwroot\REMOVED_dev\save_data.php on line 5 Here are related things from phpinfo(): System Windows NT DEV-WEB1 6.1 build 7601 (Windows Server 2008 R2 Standard Edition Service Pack 1) i586 Compiler MSVC9 (Visual C++ 2008) Architecture x86 Configure Command cscript /nologo configure.js "--enable-snapshot-build" "--enable-debug-pack" "--disable-zts" "--disable-isapi" "--disable-nsapi" "--without-mssql" "--without-pdo-mssql" "--without-pi3web" "--with-pdo-oci=C:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8=C:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8-11g=C:\php-sdk\oracle\instantclient11\sdk,shared" "--with-enchant=shared" "--enable-object-out-dir=../obj/" "--enable-com-dotnet" "--with-mcrypt=static" "--disable-static-analyze" "--with-pgo" Server API CGI/FastCGI Configuration File (php.ini) Path C:\Windows Loaded Configuration File C:\PHP\php-cgi-fcgi.ini Scan this dir for additional .ini files (none) Additional .ini files parsed (none) Registered PHP Streams php, file, glob, data, http, ftp, zip, compress.zlib, compress.bzip2, https, ftps, sqlsrv, phar Registered Stream Socket Transports tcp, udp, ssl, sslv3, sslv2, tls FTP support enabled Protocols dict, file, ftp, ftps, gopher, http, https, imap, imaps, ldap, pop3, pop3s, rtsp, scp, sftp, smtp, smtps, telnet, tftp openssl OpenSSL support enabled OpenSSL Library Version OpenSSL 0.9.8t 18 Jan 2012 OpenSSL Header Version OpenSSL 0.9.8x 10 May 2012 What am I missing here?

  Read the article

• Citrix Access Gateway with Citrix Receiver

  - by vm370

  I'm currently using a Citrix Access Gateway with firmware 5.0.4 to provide access over an SSL-VPN to an isolated environment, which is connected to over the Citrix Access Gateway Client, which is delivered by the device by default. However we encountered different problems, e.g. that it's somehow not possible to get it out of the autostart (not registered as a service or in the autostart?!) and it killed the Cisco VPN Client, which is used in the company and unfortunately cannot be replaced. The Cisco client can also just be used again after a procedure with cleaning the registry from all CAG Client remains, which requires a lot of effort. Because of that, I'd like to check if there is an alternative to this client, since is this is a real pain... Unfortunately I couldn't find a way to use the Receiver with the CAG yet, but if you have any resources on how to build this workaround, I'd be very happy. Thanks a lot in advance UPDATE: If there are other alternatives I'd be even more happy, since using the Receiver would also mean that there is an issue with the ICA-Client, which is also used in our environments. From my experience, the Receiver and the ICA-Client are also no good friends...

  Read the article

• Installinf Xen 4.0.1 in Ubuntu 10.10

  - by Hiranth

  make -f buildconfigs/mk.linux-2.6-pvops build make[3]: Entering directory /home/hirantha/xen-4.0.1' set -ex; \ if ! [ -d linux-2.6-pvops.git ]; then \ rm -rf linux-2.6-pvops.git linux-2.6-pvops.git.tmp; \ mkdir linux-2.6-pvops.git.tmp; rmdir linux-2.6-pvops.git.tmp; \ git clone -o xen -n git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git linux-2.6-pvops.git.tmp; \ (cd linux-2.6-pvops.git.tmp; git checkout -b xen/stable-2.6.32.x xen/xen/stable-2.6.32.x ); \ mv linux-2.6-pvops.git.tmp linux-2.6-pvops.git; \ fi + '[' -d linux-2.6-pvops.git ']' + rm -rf linux-2.6-pvops.git linux-2.6-pvops.git.tmp + mkdir linux-2.6-pvops.git.tmp + rmdir linux-2.6-pvops.git.tmp + git clone -o xen -n git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git linux-2.6-pvops.git.tmp Initialized empty Git repository in /home/hirantha/xen-4.0.1/linux-2.6-pvops.git.tmp/.git/ fatal: Unable to look up git.kernel.org (port 9418) (Name or service not known) make[3]: *** [linux-2.6-pvops.git/.valid-src] Error 128 make[3]: Leaving directory/home/hirantha/xen-4.0.1' make[2]: * [linux-2.6-pvops-install] Error 2 make[2]: Leaving directory /home/hirantha/xen-4.0.1' make[1]: *** [install-kernels] Error 1 make[1]: Leaving directory/home/hirantha/xen-4.0.1' make: * [world] Error 2 hirantha@hirantha-desktop:~/xen-4.0.1$ ^C hirantha@hirantha-desktop:~/xen-4.0. What is this error? How can i solve this?

  Read the article

• Random Hard Freeze of Windows 7 (is Kaspersky to be blamed for this?)

  - by Christian Ivicevic

  The last few weeks I experienced a new strange behavior of my computer. Sometimes Windows 7 just freezes with no real reason at all. While listening to music for example the playback hangs and you can hear a very nasty sound. Neither mouse nor keyboard input is handled and everything is just stuck. Using Ubuntu this does not happen, so I think it is just a matter of driver issues or a Windows 7 bug. Furthermore I am really suspicious about Kaspersky (Internet Security 11) and so I let it perform a complete virus scan while no other app is running. At about 50% it happened again and I needed to restart the computer by holding the power button the bad way... A really weird thing is that playing Skyrim this happened once, however music playback did not stop. Only the framerate dropped to 0 and sometimes for a few seconds I am able to move. Therefore I am really confused as furthermore no bluescreen pops up. Memtest told me that everything seems to be alright... Can anyone explain me which data you need about my hardware and software (and which tools tools to use to gather the informatik) to be able to provide any help on my problem?

  Read the article

• "A disk read error occurred" when booting XP disk image in VirtualBox

  - by intuited

  I'm trying to boot an XP installation cloned into VirtualBox from a real drive. I'm getting the message A disk read error occurred Press Ctrl+Alt+Del to restart whenever* I try to boot the machine. * This is not strictly true: with AMD-V enabled, the boot process appears to not make it this far and instead hangs at a black screen with cursor. I created the VirtualBox image from the original drive using the following method: $ sudo ddrescue -n /dev/sdd sdd.img logfile # completed without errors $ VBoxManage convertfromraw sdd.img disk.vdi The original disk (and the image) contain a single NTFS partition with XP installed on it. The owner of the drive indicates that it did boot okay the last time the system made it that far. The (Pentium 4) system has a broken (enormous) heat sink, so at some point it failed to boot because it would quickly overheat and shut down. If I boot the VM from a live cd, I am able to mount its /dev/sda1 without any problems. I ran ntfsfix and didn't have any luck. I've read through the instructions on doing this. I didn't really follow them. For example, I didn't run MergeIDE before imaging because the machine was not bootable. However, the symptom of that problem seems to be quite different. The emitted message is contained in the volume boot record of the XP partition, which leads me to suspect that this is a problem with the core operating system bootstrap procedure, and not related to anything in the registry. I don't have an XP boot CD.

  Read the article

• E-mail hosting provider that can set up aliases with wildcards

  - by Richard Downer

  I am looking for an e-mail hosting provider that allow e-mail aliases containing wildcards. In more detail: I own my own domain. I want an e-mail hosting provider to manager e-mail for my domain. Now, to help deal with spam, I often give different e-mail addresses to different organisations. These e-mail addresses always start with the same prefix, but then differ. So, for example, I might give out these e-mail addresses: [email protected] [email protected] [email protected] I want to be able to go to the e-mail provider's control panel and set up an e-mail alias like this: [email protected] -- bounce/discard (because this address has been sold to spammers) joe-*@sample.com -- redirect to [email protected] What's I don't want to do is either have to set up every single e-mail address individually (because I make them up whenever I need them), nor do I want to have a general catch-all for any unrecognised address in my domain (because I don't want to be carpet-bombed with spam when a spammer runs a dictionary attack against my domain name.) Although this seems like a useful feature to have, it seems to be a little-known feature and I've not seen anybody advertise this feature. My current hosting provider offer this but I want to move away from them, so I need another provider that will continue to work with all the e-mail addresses I've been using for years. Alternatively, I could use mail server software that runs on Windows - I have seen some commercial packages offering this feature but they cost more than I can afford - are there any suggestions for low-cost software packages?

  Read the article

• How to write files in specific order?

  - by Bernie

  Okay, here's a weird problem -- My wife just bought a 2014 Nissan Altima. So, I took her iTunes library and converted the .m4a files to .mp3, since the car audio system only supports .mp3 and .wma. So far so good. Then I copied the files to a DOS FAT-32 formatted USB thumb drive, and connected the drive to the car's USB port, only to find all of the tracks were out of sequence. All tracks begin with a two digit numeric prefix, i.e., 01, 02, 03, etc. So you would think they would be in order. So I called Nissan Connect support and the rep told me that there is a known problem with reading files in the correct order. He said the files are read in the same order they are written. So, I manually copied a few albums with the tracks in a predetermined order, and sure enough he was correct. So I copied about 6 albums for testing, then changed to the top level directory and did a "find . music.txt". Then I passed this file to rsync like this: rsync -av --files-from=music.txt . ../Marys\ Music\ Sequenced/ The files looked like they were copied in order, but when I listed the files in order of modified time, they were in the same sequence as the original files: ../Marys Music Sequenced/Air Supply/Air Supply Greatest Hits ls -1rt 01 Lost In Love.mp3 04 Every Woman In The World.mp3 03 Chances.mp3 02 All Out Of Love.mp3 06 Here I Am (Just When I Thought I Was Over You).mp3 05 The One That You Love.mp3 08 I Want To Give It All.mp3 07 Sweet Dreams.mp3 11 Young Love.mp3 So the question is, how can I copy files listed in a file named music.txt, and copy them to a destination, and ensure the modification times are in the same sequence as the files are listed?

  Read the article

• VRF Internet Gateway Multiple External IP's 1 Internal IP to AWS

  - by user223903

  Trying to setup VRF for the first time and its not working for me even though I keep reading everything online. IP's are different to real life. I have an Internet connection which I can ping to my router in the current setup below 195.45.73.22 I have a block of ip addresses 195.45.121.0/27 I want to setup multiple VPN's to AWS so need to have multiple external ip's thus the block of IP addresses. I have setup the 2nd and 3rd IP address but can not ping them from external. Any help would be grateful. Bryan ip source-route ! ip vrf Internet rd 1:1 route-target export 1:1 route-target import 1:1 ip vrf AWSSydney1 rd 2:2 route-target export 2:2 route-target import 2:2 route-target import 1:1 ip vrf AWSSydney2 rd 3:3 route-target export 3:3 route-target import 3:3 route-target import 1:1 ip cef no ip domain lookup no ipv6 cef multilink bundle-name authenticated interface FastEthernet0/0 description Vocus Internet no ip address speed 100 full-duplex interface FastEthernet0/0.1 encapsulation dot1Q 1 native ip address 195.45.73.22 255.255.255.252 interface FastEthernet0/0.2 encapsulation dot1Q 2 ip vrf forwarding AWSSydney1 ip address 195.45.121.1 255.255.255.224 interface FastEthernet0/0.3 encapsulation dot1Q 3 ip vrf forwarding AWSSydney2 ip address 195.45.121.2 255.255.255.224 interface FastEthernet0/1 description LAN_SIDE ip address 10.0.0.5 255.255.255.0 speed 100 full-duplex no mop enabled ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 195.45.73.21 ip route vrf Internet 0.0.0.0 0.0.0.0 195.45.73.21

  Read the article

• atl90.dll version 9.0.30729.4148 is missing in WinSxS folder

  - by mkva

  Hi I have the following problem: when starting Visual Studio 2008, it says "Cannot find one or more components. Please reinstall the application." and stops. With the help of Sysinternals ProcessMonitor, I found out that Visual Studio could not load the atl90.dll 9.0.30729.4148 from the WinSxS folder. I tried to manually copy the older atl90.dll 9.0.30729.1 with the result that Visual Studio works again. Now I call this a dirty workaround, and not a solution. Plus I still don't know the reason why the atl90.dll disappeared in the first place. So my questions: - Does anyone know of a reason why this might have happened? - Does anyone know a real solution to the problem, e.g. a Microsoft download that includes the atl90.dll in the correct version 9.0.30729.4148 that installs into WinSxS? Some details: - WinXp SP3 - missing DLL: C:\WINNT\WinSxS\x86_Microsoft.VC90.ATL_1fc8b3b9a1e18e3b_9.0.30729.4148_x-ww_353599c2\atl90.dll - workaround DLL: C:\WINNT\WinSxS\x86_Microsoft.VC90.ATL_1fc8b3b9a1e18e3b_9.0.30729.1_x-ww_d01483b2\atl90.dll - manifests in WinSxS seem to be alright, but unfortunately all point to the missing version 9.0.30729.4148 Thanks, Markus

  Read the article

• atl90.dll version 9.0.30729.4148 is missing in WinSxS folder

  - by mkva

  I have the following problem: when starting Visual Studio 2008, it says "Cannot find one or more components. Please reinstall the application." and stops. With the help of Sysinternals ProcessMonitor, I found out that Visual Studio could not load the atl90.dll 9.0.30729.4148 from the WinSxS folder. I tried to manually copy the older atl90.dll 9.0.30729.1 with the result that Visual Studio works again. Now I call this a dirty workaround, and not a solution. Plus I still don't know the reason why the atl90.dll disappeared in the first place. So my questions: - Does anyone know of a reason why this might have happened? - Does anyone know a real solution to the problem, e.g. a Microsoft download that includes the atl90.dll in the correct version 9.0.30729.4148 that installs into WinSxS? Some details: - WinXp SP3 - missing DLL: C:\WINNT\WinSxS\x86_Microsoft.VC90.ATL_1fc8b3b9a1e18e3b_9.0.30729.4148_x-ww_353599c2\atl90.dll - workaround DLL: C:\WINNT\WinSxS\x86_Microsoft.VC90.ATL_1fc8b3b9a1e18e3b_9.0.30729.1_x-ww_d01483b2\atl90.dll - manifests in WinSxS seem to be alright, but unfortunately all point to the missing version 9.0.30729.4148 Thanks, Markus

  Read the article

• pure-ftpd not listening on specified port

  - by Jason McLaren

  I installed the pure-ftpd package (version 1.0.35-1) on an Ubuntu 12.04 box (an EC2 instance based on the standard Ubuntu 12.04 AMI). The pure-ftpd daemon is running (verified with ps), though there is no PID file (expected one to be created by the /etc/init.d/pure-ftpd script). Here's the resulting command that gets run by the init.d script: /usr/sbin/pure-ftpd -l pam -O clf:/var/log/pure-ftpd/transfer.log -o -8 UTF-8 -u 1000 -E -B -g /var/run/pure-ftpd/pure-ftpd.pid Here's my real problem: the ftp server isn't actually listening on any port (checked with netstat and nmap). So I can't ftp to the server (either locally using localhost or remotely using the public IP address). I tried adding a Bind file to /etc/pure-ftpd/conf and restarting, but it didn't help. When I installed pure-ftpd, it replaced inetd with openbsd-inetd, but did not run it since there were no services enabled. So inetd is not listening on port 21 either. (Apparently Ubuntu has a no-inetd-by-default policy, according to https://lists.ubuntu.com/archives/ubuntu-users/2010-September/227905.html .) I want to run pure-ftpd by itself (not with inetd) anyways, since the /etc/init.d/pure-ftpd script requires no inetd if you use the UploadScript feature. I'm not familiar with how Ubuntu handles network services (and can't find any relevant docs besides generic man pages), so I'm probably missing something obvious. Nothing seems out of the ordinary with /etc/hosts.allow (empty) or hosts.deny (empty), and I didn't add any firewall rules (iptables -L shows that the firewall is in its initial state). I've checked the pure-ftpd docs; not sure what else to look at. Any help would be appreciated, thanks!

  Read the article

• remote telnet and email

  - by Mustafa Ismail Mustafa

  This issue has been occupying my work for the last few days and I will be understating when I say its driven me up the blasted walls. Essentially, I can ping and tracert the domain jnrcs.org and the subdomains mail.jnrcs.org and mail.jordanredcrescent.org. All three mentioned point to ip address 212.38.147.97. About 4 days ago, when we registered the domain "jnrcs.org" suddenly all external connection to the mail server from outside was lost. Not just mail, but other http based port-forwarded or natted services (such as camera surveillance and pbx services). I tried good old telnet (I'm a linux user) and I get the following output: telnet> o mail.jnrcs.org 25 Trying 212.38.147.97... telnet: Unable to connect to remote host: No route to host telnet> Tracert gives me: traceroute to mail.jnrcs.org (212.38.147.97), 30 hops max, 60 byte packets 1 192.168.1.2 (192.168.1.2) 0.869 ms 0.944 ms * 2 * * * 3 * * * 4 * * * 5 * * * 6 * 212.38.128.118 (212.38.128.118) 33.875 ms 39.187 ms 7 * * * 8 * * * 9 * * * 10 * * * 11 * * 212.38.147.97 (212.38.147.97) 67.621 ms I am stumped. Other friends from all around the world can telnet no problem. What could have possibly happened to make telnet/smtp/pop/imap/http access stop? Please bear in mind I'm primarily a developer but I [am under the delusion] that I can carry my weight in IT administration :) TIA

  Read the article

• Ripping a home video VCD on Linux or Windows with VLC or otherwise

  - by user259774

  I have a VCD with 22 minutes of video on it. I would like to retain this footage and throw away the VCD. I can play the whole thing with VLC ("open disc - vcd - /dev/sr0 - play"): all 22 minutes of the main track. I don't believe there's any other content aside from the main track. I can seek to anywhere I want to within the 22 minute track. If I mount /dev/sr0 /media/vcd and then try to copy the only file from the MPEGAV folder, I get an I/O error, with an empty destination file. VLC has a "convert" option in addition to "play". When I use this I actually get a good OGG file back, after it runs through the video in painful real-time. I guess it dubs it frame-by-frame. But the file is only 10 minutes long, leaving 12 minutes off of the track. Handbrake doesn't detect it's track titles, unfortunately. I don't know if I should start getting involved with GNU ddrescue or if it's because VCDs somehow encode their data sectors differently. Anyway, I'm in way over my head and if anyone knows how I could get that video track off the thing, feel free to share! Edit: I should note that I also have access to a Windows computer

  Read the article

< Previous Page | 544 545 546 547 548 549 550 551 552 553 554 555  | Next Page >