Search Results

Search found 17727 results on 710 pages for 'large apps'.

Page 549/710 | < Previous Page | 545 546 547 548 549 550 551 552 553 554 555 556  | Next Page >

  • Why datacenter water cooling is not widespread?

    - by MainMa
    From what I read and hear about datacenters, there are not too many server rooms which use water cooling, and none of the largerst datacenters use water cooling (correct me if I'm wrong). Also, it's relatively easy to buy an ordinary PC components using water cooling, while water cooled rack servers are nearly nonexistent. On the other hand, using water can possibly (IMO): Reduce the power consumption of large datacenters, especially if it is possible to create direct cooled facilities (i.e. the facility is located near a river or the sea). Reduce noise, making it less painful for humans to work in datacenters. Reduce space needed for the servers: On server level, I imagine that in both rack and blade servers, it's easier to pass the water cooling tubes than to waste space to allow the air to pass inside, On datacenter level, if it's still required to keep the alleys between servers for maintenance access to servers, the empty space under the floor and at the ceiling level used for the air can be removed. So why water cooling systems are not widespread, neither on datacenter level, nor on rack/blade servers level? Is it because: The water cooling is hardly redundant on server level? The direct cost of water cooled facility is too high compared to an ordinary datacenter? It is difficult to maintain such system (regularly cleaning the water cooling system which uses water from a river is of course much more complicated and expensive than just vacuum cleaning the fans)?

    Read the article

  • Bad Performance when SQL Server hits 99% Memory Usage

    - by user15863
    I've got a server that reports 8 GB of ram used up at 99%. When restart Sql Server, it drops down to about 5% usage, but gradually builds back up to 99% over about 2 hours. When I look at the sqlserver process, its reported as only using 100k ram, and generally never goes up or below that number by very much. In fact, if I add up all the processes in my TaskManager, it's barely scratching the surface of my total available (yet TaskManager still shows 99% memory usage with "All processes shown"). It appears that Sql Server has a huge memory leak going on but it's not reporting it. The server has ran fine for nearly two years, with this only starting to manifest itself in the last 3-4 weeks. Anyone seen this or have any insight into the problem? EDIT When the server hits 99%, performance goes down hill. All queries to the server, apps, etc. come to a crawl. Restarting the service makes things zippy again, until 2 hours has passed and the server hits 99% once again.

    Read the article

  • How to configure Hyper-V failover cluster to live migrate when dynamic memory runs out?

    - by Matt Johnson
    Appologies in advance that this is not a direct programming question, but I have a feeling that the solution involves custom powershell scripts (maybe), so this is as good a place to ask as any. I maintain a website that has a large Hyper-V cluster for SQL Servers. We are using Windows 2008 R2 SP1, and the new "dynamic memory" feature. I've already ready reviewed the Best Practices Guide, and implemented it's suggested configuration. Everything works well, except that when SQL demand increases memory pressure to expand to more memory than is available on the physical machine, the memory status goes into the "Warning" state and stays there. I assume the hypervisor is using a swapfile on the host to fulfill the memory requirement, thus slowing the virtual machine down. When this happens, there are plenty of other nodes in the cluster that have available resources. I can live-migrate the virtual server over there and everything works, and the warnings go away. Now how can I automate this? I see no menu options in either Hyper-V or the Failover Cluster Manager for performing a migration or shutdown when dynamic memory goes into the warning state. Any ideas about how to script this, or monitor it and invoke the action directly, would be helpful. If the solution involves coding, powershell would be ideal, but I could envison this as a .Net Service that monitors for this state and kicks off the migration request. I just don't know what objects are involved in doing the monitoring or kicking off the live migration. Thanks in advance.

    Read the article

  • Apache Won't Restart After Compiling PHP with Postgres

    - by gonzofish
    I've compiled PHP (v5.3.1) with Postgres using the following configure: ./configure \ --build=x86_64-redhat-linux-gnu \ --host=x86_64-redhat-linux-gnu \ --target=x86_64-redhat-linux-gnu \ --program-prefix= \ --prefix=/usr/ \ --exec-prefix=/usr/ \ --bindir=/usr/bin/ \ --sbindir=/usr/sbin/ \ --sysconfdir=/etc \ --datadir=/usr/share \ --includedir=/usr/include/ \ --libdir=/usr/lib64 \ --libexecdir=/usr/libexec \ --localstatedir=/var \ --sharedstatedir=/usr/com \ --mandir=/usr/share/man \ --infodir=/usr/share/info \ --cache-file=../config.cache \ --with-libdir=lib64 \ --with-config-file-path=/etc \ --with-config-file-scan-dir=/etc/php.d \ --with-pic \ --disable-rpath \ --with-pear \ --with-pic \ --with-bz2 \ --with-exec-dir=/usr/bin \ --with-freetype-dir=/usr \ --with-png-dir=/usr \ --with-xpm-dir=/usr \ --enable-gd-native-ttf \ --with-t1lib=/usr \ --without-gdbm \ --with-gettext \ --without-gmp \ --with-iconv \ --with-jpeg-dir=/usr \ --with-openssl \ --with-zlib \ --with-layout=GNU \ --enable-exif \ --enable-ftp \ --enable-magic-quotes \ --enable-sockets \ --enable-sysvsem \ --enable-sysvshm \ --enable-sysvmsg \ --with-kerberos \ --enable-ucd-snmp-hack \ --enable-shmop \ --enable-calendar \ --with-libxml-dir=/usr \ --enable-xml \ --with-system-tzdata \ --with-mime-magic=/usr/share/file/magic \ --with-apxs2=/usr/sbin/apxs \ --with-mysql=/usr/include/mysql \ --without-gd \ --with-dom=/usr/include/libxml2/libxml \ --disable-dba \ --without-unixODBC \ --disable-pdo \ --enable-xmlreader \ --enable-xmlwriter \ --without-sqlite \ --without-sqlite3 \ --disable-phar \ --enable-fileinfo \ --enable-json \ --without-pspell \ --disable-wddx \ --with-curl=/usr/include/curl \ --enable-posix \ --with-mcrypt \ --enable-mbstring \ --with-pgsql=/mnt/mv/pgsql I'm using Postgres 8.4.0 and Apache 2.2.8; I have the following line in my Apache conf file: LoadModule php5_module /usr/lib64/httpd/modules/libphp5.so And when I attempt to restart Apache, I get the following error message: Starting httpd: httpd: Syntax error on line 205 of /etc/httpd/conf/httpd.conf: Cannot load /usr/lib64/httpd/modules/libphp5.so into server: /usr/lib64/httpd/modules/libphp5.so: undefined symbol: lo_import_with_oid Now, I know that this is a problem with Postgres with PHP because lo_import_with_oid is a function in the Postgres source which allows the importing of large objects; also, if I remove the --with-pgsql option, PHP and Apache get along great. I've scoured the Internet looking for answers all day, but to no avail. Does anyone have ANY insight into what is causing my problems.

    Read the article

  • some PDF's to iPhones via ActiveSync are corrupt

    - by longneck
    we have two server applications (one .NET/ASP web app, the other a native Windows app) that generate PDF's that are then emailed to our users on Exchange 2010. the apps deliver the emails to the Exchange server via SMTP, and our iPhone/iPad users receive their email via activesync. pretty much all of the PDF's generated by the web app and many of the PDF's generated by the Windows app fail to open on an iPhone or iPad. tapping the attachment shows the screen that would display the PDF with the name of the file at the top but the bottom of the screen is completely grey. one thing i have figured out is that the attachment on the iPad is uuencoded. forwarding the attachment to another email address shows the uuencoded format. here's a sample: begin 600 unknown M)5!$1BTQ+C0-)>+CS],-"C8@,"!O8FH\/"](6S8U-B`Q-#A=+TQI;F5A<FEZ M960@,2]%(#DQ-#8O3"`Q,S`Q.2].(#$O3R`Y+U0@,3(X-3,^/@UE;F1O8FH- ---snip--- M,C8T,"`P,#`P,"!N#0IT<F%I;&5R#0H\/"]3:7IE(#8^/@T*<W1A<G1X<F5F .#0HQ,38-"B4E14]&#0H` ` end whereas the normal version of the file looks like a normal PDF: %PDF-1.4 %âãÏÓ 6 0 obj<</H[656 147]/Linearized 1/E 9698/L 13571/N 1/O 9/T 13405>> ---snip--- trailer <</Size 6>> startxref 116 %%EOF so i think the problem is that the attachment is being double uuencoded somewhere, or the iPhone is failing to recognize that the attachment is uuencoded and not decoding it. any suggestions on where to begin troubleshooting this problem?

    Read the article

  • Experience with AMCC 3ware 9650se raid cards? Ours seems dead

    - by antiduh
    We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated. Edit: These are the kernel errors we see: 3ware 9000 Storage Controller device driver for Linux v2.26.02.012. 3w-9xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 3w-9xxx 0000:09:00.0: setting latency timer to 64 3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing. 3w-9xxx: scsi0: ERROR: (0x06:0x001F): Microcontroller not ready during reset sequence. 3w-9xxx: scsi0: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. 3w-9xxx 0000:09:00.0: PCI INT A disabled

    Read the article

  • Xbox 360 formatting for MP4 h.264?

    - by Kayle
    For the life of me, I can't get the Xbox 360 to recognize anything other than a WMV. It's full updated with Xbox Live and I even added all the Video apps (Zune, Netflix, etc) just to see if it would force some sort of codec update. I'm using handbrake, at the moment, to try and convert an mkv with subtitles. Handbrake burns the subtitles into the video for me, which is important. I can't figure out what is missing though, as the Xbox refuses to acknowledge my MP4s. Here's the VLC codec info output: As far as I can tell, this is EXACTLY what the xbox supports. I don't want to convert every video twice by throwing it through Windows Movie Maker just to get it to WMV. None of the converters mentions above output to WMV and I don't like WMV since it's not as universal as MP4. I've tried changing the container name manually to M4V, MOV, and AVI to see if I can trick the Xbox... no beans. The video displays perfectly in WMP, of course. If I convert it to WMV, suddenly it works fine. But I don't find this acceptable, as I know the Xbox is supposed to support other filetypes. If anyone knows why my Xbox won't play anything but WMVs, I would be very appreciative to know why! It's driving me nuts. The only other information I can think to include is that it's about 3 years old and of the cheapest variety (Xbox Arcade). I've added a hard drive, xbox live, and have thoroughly updated it. Maybe there's a specific video update I'm unaware of??

    Read the article

  • NFS v4, HA Migration, and stale handles on clients

    - by Karl Katzke
    I'm managing a server running NFS v4 with Pacemaker/OpenAIS. NFS is configured to use TCP. When I migrate the NFS server to another node in the Pacemaker cluster, even though the metadata is persisted, connections from the clients 'hang' and eventually time out after 90 seconds. After that 90 seconds, the old mountpoint becomes 'stale' and the mounted files can no longer be accessed. The 90 second grace period seems to be part of the server configuration and not the client configuration. I see this message on the server: kernel: NFSD: starting 90-second grace period If I restart the NFS client on the client nodes after I migrate (unmounting and then remounting the share), then I don't experience the problem, but connections and file transfers still interrupted. Three questions: What is the 90 second grace period? What's it there for? How can I keep the files from going stale on the clients without restarting them after I migrate the NFS server to another node? Is it actually possible to migrate the NFS server without having large file uploads drop?

    Read the article

  • How can the little guys effectively learn and use puppet?

    - by drumfire
    Six months ago, in our not-for-profit project we decided to start migrating our system management to a Puppet controlled environment because we are expecting our number of servers to grow substantially between now and a year from now. Since the decision has been made our IT guys have become a bit too annoyed a bit too often. Their biggest objections are: "We're not programmers, we're sysadmins"; Modules are available online but many differ from one another; wheels are being reinvented too often, how do you decide which one fits the bill; Code in our repo is not transparent enough, to find how something works they have to recurse through manifests and modules they might have even written themselves a while ago; One new daemon requires writing a new module, conventions have to be similar to other modules, a difficult process; "Let's just run it and see how it works" Tons of hardly known 'extensions' in community modules: 'trocla', 'augeas', 'hiera'... how can our sysadmins keep track? I can see why a large organisation would dispatch their sysadmins to puppet courses to become puppet masters. But how would smaller players get to learn puppet to a professional level if they do not go to courses and basically learn it via their browser and editor?

    Read the article

  • Folder Redirection Issues - Freezing, Strange Warnings

    - by JCardenas
    I have Folder Redirection set up in a test environment for a couple accounts. I have followed the instructions for setting up the folder security settings here, and I can confirm that folders are created automatically by the system with the correct security settings when a user logs in. The GPO has been configured to automatically move user files up to the redirected folders, and this is working properly. Problems start occurring when a Windows 7 PC is in use. It is rare, but Explorer will lock up when performing a file write operation (move/copy/save from application). This results in the entire system being unusable, with only a hard reset resolving it (Task Manager doesn't start, the "three finger salute" does nothing, apps stop working). The mouse functions, but clicks do nothing. The other issue is that occasionally when copying/creating/modifying files a dialog box will pop up with the message "You need permission to perform this action. You require permission from XYZ\cardenas to make changes to this folder." The folder that was created by copying an existing one has the correct security settings and lists me as the owner. My company will not be implementing Folder Redirection on XP, since we are making a "clean break" with implementing new technologies with the Windows 7 rollout, so this behavior has not been - nor will be - checked for in XP. Thanks in advance for your help!

    Read the article

  • Bash script 'while read' loop causes 'broken pipe' error when run with GNU Parallel

    - by Joe White
    According to the GNU Parallel mailing list this is not a GNU Parallel-specific problem. They suggested that I post my problem here. The error I'm getting is a "broken pipe" error, but I feel I should first explain the context of my problem and what causes this error. It happens when trying to use any bash script containing a 'while read' loop in GNU Parallel. I have a basic bash script like this: #!/bin/bash # linkcheck.sh while read domain do host "$domain" done Assume that I want to pipe in a large list (250mb say). cat urllist | ./linkcheck.sh Running host command on 250mb worth of URLs is rather slow. To speed things up I want to break up the input into chunks before piping it and then run multiple jobs in parallel. GNU Parallel is capable of doing this. cat urllist | parallel --pipe -j0 parallel ./linkcheck.sh {} {} is substituted by the contents of urllist line-by-line. Assume that my systems default setup is capable of running 500ish jobs per instance of parallel. To get round this limitation we can parallelize Parallel itself: cat urllist | parallel -j10 --pipe parallel -j0 ./linkcheck.sh {} This will run 5000'ish jobs. It will also, sadly, cause the error "broken pipe" (bash FAQ). Yet the script starts to work if I remove the while read loop and take input directly from whatever is fed into {} e.g., #!/bin/bash # linkchecker.sh domain="$1" host "$1" Why will it not work with a while read loop? Is it safe to just turn off the SIGPIPE signal to stop the "broken pipe" message, or will that have side effects such as data corruption? Thanks for reading.

    Read the article

  • Running SSL locally on a hosts redirected domain name with Ubuntu and Apache

    - by Matthew Brown
    I recently made some changes to my Ubuntu computer so that a domain name resolved to my local copy of Apache. I edited /etc/hosts and added 127.0.0.1 thisbit.example.com Then set up a VirtualHost for the responses I wishes to create. That all works fine and my testing is now shooting on ahead without harm or risk tot he production server. Now for my next trick I need to test the authentication and so need to do this with HTTPS Basically https://auth.example.com needs to work on my PC without the SSL causing an issue which I imagine would be the case as I am clearly not the true https://auth.example.com but for the basis of this exercise I need to pretend that I am. Now it might be that the Apps I'm testing don't worry about checking the certificate. (Many are in Java which I'm no expert with). What gotchas am I likely to encounter and what is the best way of not letting my own hacks spoil my testing? I'm guessing the place to start is to enable SSL with Apcahe... I've never done that before as it has never come up before.

    Read the article

  • Windows Terminal Server: occasional memory violation for applications

    - by syneticon-dj
    On a virtualized (ESXi 4.1) Windows Server 2008 SP2 32-bit machine which is used as a terminal server, I occasionally (approximately 1-3 event log entries a day) see applications fail with an 0xc0000005 error - apparently a memory access violation. The problem seems quite random and only badly reproducable - applications may run for hours, fail with 0xc0000005 and restart quite fine or just throw the access violation at startup and start flawlessly at the second attempt. The names of executables, modules and offset addresses vary, although a single executable tends to fail with same modules and the same memory offset addresses (like "OUTLOOK.EXE" repeatedly failing on module "olmapi32.dll" with the offset "0x00044b7a") - even across multiple user's logons and with several days passing without a single failure inbetween. The offset addresses seem to change across reboots, however. Only selective executables seem affected by the problem, although I may simply not be seeing a sufficient number of application runs from the other ones. I first suspected a possible problem with the physical machine's RAM, but ruled this out as a rather unlikely cause - the memory comes with ECC and I've already moved the virtual machine across several times, without any perceptable change. I've seen that DEP was enabled in "OptOut" mode on this machine: C:\Users\administrator>wmic OS Get DataExecutionPrevention_SupportPolicy DataExecutionPrevention_SupportPolicy 3 and tried changing the policy to OptIn via startup options: bcdedit.exe /set {current} nx OptIn but have yet to see any effect - I also would expect Outlook 12 or Adobe Reader 9 (both affected applications) to play well with DEP. Any other ideas why the apps may be failing?

    Read the article

  • iTunes Home Sharing only works one way between 2 WinXP PC's on the same LAN

    - by scunliffe
    Both PC's have the latest iTunes installed. PC (A) can "see" that there is a shared library "B library" but attempts to connect to it return this error message: The shared library "{Username}'s Library" is not responding (-3259) Check that any firewall software running on either the shared computer or this computer has been set to allow communication on port 3689. however the reverse works fine. e.g. PC (B) can "see" shared library "A library" and can access all content. Notes: Both PC's have Home Sharing enabled (turned off/on several times to verify). Both PC's have Windows Firewall turned on, but in the exceptions tab, iTunes is allowed, and Port 3689 is also added as a firewall exception (just in case) Both iTunes accounts have been "authorized" on both PC's Both PC's connect via LAN via D-Link DIR-615 router. In the advanced application rules, iTunes has also been added to allow traffic on port 3689 un-hindered. Is there any other magical setting/configuration option that I should be aware of and set in order to get this to work? I could care less about sharing apps etc. I just want the music sharing to work. Update: Solved! It turns out on PC (B) there were multiple accounts set up. 1 of the accounts had the checkbox checked under the windows firewall "On" option which states "No exceptions" thus even though it was added to the exception list on the main user account, this other account was blocking access.

    Read the article

  • How to tell if Microsoft Works is 32 or 64 bit? Please Help!

    - by Bill Campbell
    Hi, I am trying to convert one of our apps to run on Win7 64 bit from XP 32 bit. One of the things that it uses is Excel to import files. It's a little complicated since it was using Microsoft.Jet.OLEDB.4.0 (Excel). I found Office 14 (2010) has a 64bit version I can download. I downloaded Office 2010 Beta but it didn't seem to install Microsoft.ACE.OLEDB.14.0. I found that I could download 2010 Office System Driver Beta: Data Connectivity Components which has the ACE.OLEDB.14 in it but when I try to install it, the installed tells me "You cannot install the 64-bit version of Access Database engine for Microsoft Office 2010 because you currently have 32-bit Office products installed". How do I determine what 32bit office products this is reffering to? My Dell came with Microsoft Works installed. I don't know if this is 32 or 64 bit. Is there anyway to tell? I don't want to uninstall this if it's not the problem and I'm not sure what else might be the problem. Any help would be appreciated! thanks, Bill

    Read the article

  • Mounting 2.5" SSD in Antec Atlas 550's 3.5" bay

    - by cecilkorik
    Just got some new SSDs to add to my servers, unfortunately there doesn't appear to be anywhere to actually mount them. The cases are Antec Atlas 550 mid-tower server cases. The problem is that the 3.5" bays are intended for 3.5" hard drives (obviously) not SSDs, so they are mounted from the bottom with rubber grommets to reduce vibration. There are NO side-holes in any of the 3.5" bays, all mounting has to be done from the bottom of the drive, through the thick rubber grommets, which requires special extra-long screws with large heads. Those screws will not work with the SSD, the thread is too coarse, 2.5" drives apparently use M3 screws with a finer pitch. The case's 3.5" bays have holes aligned for 2.5" drives and by moving the grommets into the appropriate holes they line up with the SSD. But that's as far as I can get. I don't have and cannot find any screws that use the finer M3 pitch that are long enough and have the wide head. I can't remove the grommets because the screw holes are much too wide without them, the entire head of the screw fits through. And again, there are no side-holes, so I can't use the mounting bracket that came with the drive nor any other 2.5"-3.5" bracket I've found. Here is a pic of what I am dealing with (note that the SSD is just resting on the case, it's not currently screwed in if that's not clear) Any ideas for safely mounting these little guys without resorting to duct tape or superglue would be very appreciated. If anyone knows where I could buy the appropriate type of M3 threaded screw or has any other ideas please help me out here.

    Read the article

  • MS SQL Server slows down over time?

    - by Dave Holland
    Have any of you experienced the following, and have you found a solution: A large part of our website's back-end is MS SQL Server 2005. Every week or two weeks the site begins running slower - and I see queries taking longer and longer to complete in SQL. I have a query that I like to use: USE master select text,wait_time,blocking_session_id AS "Block", percent_complete, * from sys.dm_exec_requests CROSS APPLY sys.dm_exec_sql_text(sql_handle) AS s2 order by start_time asc Which is fairly useful... it gives a snapshot of everything that's running right at that moment against your SQL server. What's nice is that even if your CPU is pegged at 100% for some reason and Activity Monitor is refusing to load (I'm sure some of you have been there) this query still returns and you can see what query is killing your DB. When I run this, or Activity Monitor during the times that SQL has begun to slow down I don't see any specific queries causing the issue - they are ALL running slower across the board. If I restart the MS SQL Service then everything is fine, it speeds right up - for a week or two until it happens again. Nothing that I can think of has changed, but this just started a few months ago... Ideas? --Added Please note that when this database slowdown happens it doesn't matter if we are getting 100K page views an hour (busier time of day) or 10K page views an hour (slow time) the queries all take a longer time to complete than normal. The server isn't really under stress - the CPU isn't high, the disk usage doesn't seem to be out of control... it feels like index fragmentation or something of the sort but that doesn't seem to be the case. As far as pasting results of the query I pasted above I really can't do that. The Query above lists the login of the user performing the task, the entire query, etc etc.. and I'd really not like to hand out the names of my databases, tables, columns and the logins online :)... I can tell you that the queries running at that time are normal, standard queries for our site that run all the time, nothing out of the norm.

    Read the article

  • Can't find standalone Chrome Gmail client that I know exists

    - by Carson
    I'm on Windows. A couple years ago when I switched from Outlook to Gmail (Google Apps), Google provided this awesome little standalone gmail client that was just a single-purpose Chrome install. It launched like a normal application, stayed updated when I updated Chrome. It was Chrome in a separate application that launched only gmail, stayed logged in really well, and "felt" like a gmail mail client, with the gmail interface. It had it's own little red envelope icon, it was a windows app. (I remember there was no Mac equivalent.) I found it while looking through the "this is how you get your company to switch to gmail" documentation that Google provided. I just repaved my box and now I'm looking for this thing again, and I had no idea it would be impossible to find. I've spent literally 2 hours looking, searching, googling, etc. I'm losing my mind. Anyone know how I can get my hands on this? I used it all day every day for 2 years, so I know it exists :), but I can not find it. Any assistance would be gratefully received.

    Read the article

  • How to list rpm packages/subpackages sorted by total size

    - by smci
    Looking for an easy way to postprocess rpm -q output so it reports the total size of all subpackages matching a regexp, e.g. see the aspell* example below. (Short of scripting it with Python/PERL/awk, which is the next step) (Motivation: I'm trying to remove a few Gb of unnecessary packages from a CentOS install, so I'm trying to track down things that are a) large b) unnecessary and c) not dependencies of anything useful like gnome. Ultimately I want to pipe the ouput through sort -n to what the space hogs are, before doing rpm -e) My reporting command looks like [1]: cat unwanted | xargs rpm -q --qf '%9.{size} %{name}\n' > unwanted.size and here's just one example where I'd like to see rpm's total for all aspell* subpackages: root# rpm -q --qf '%9.{size} %{name}\n' `rpm -qa | grep aspell` 1040974 aspell 16417158 aspell-es 4862676 aspell-sv 4334067 aspell-en 23329116 aspell-fr 13075210 aspell-de 39342410 aspell-it 8655094 aspell-ca 62267635 aspell-cs 16714477 aspell-da 17579484 aspell-el 10625591 aspell-no 60719347 aspell-pl 12907088 aspell-pt 8007946 aspell-nl 9425163 aspell-cy Three extra nice-to-have things: list the dependencies/depending packages of each group (so I can figure out the uninstall order) Also, if you could group them by package group, that would be totally neat. Human-readable size units like 'M'/'G' (like ls -h does). Can be done with regexp and rounding on the size field. Footnote: I'm surprised up2date and yum don't add this sort of intelligence. Ideally you would want to see a tree of group-package-subpackage, with rolled-up sizes. Footnote 2: I see yum erase aspell* does actually produce this summary - but not in a query command. [1] where unwanted.txt is a textfile of unnecessary packages obtained by diffing the output of: yum list installed | sed -e 's/\..*//g' > installed.txt diff --suppress-common-lines centos4_minimal.txt installed.txt | grep '>' and centos4_minimal.txt came from the Google doc given by that helpful blogger.

    Read the article

  • MySQL is killing the server IO.

    - by OneOfOne
    I manage a fairly large/busy vBulletin forums (running on gigenet cloud), the database is ~ 10 GB (~9 milion posts, ~60 queries per second), lately MySQL have been grinding the disk like there's no tomorrow according to iotop and slowing the site. The last idea I can think of is using replication, but I'm not sure how much that would help and worried about database sync. I'm out of ideas, any tips on how to improve the situation would be highly appreciated. Specs : Debian Lenny 64bit ~12Ghz (6x2GHz) CPU, 7520gb RAM, 160gb disk. Kernel : 2.6.32-4-amd64 mysqld Ver 5.1.54-0.dotdeb.0 for debian-linux-gnu on x86_64 ((Debian)) Other software: vBulletin 3.8.4 memcached 1.2.2 PHP 5.3.5-0.dotdeb.0 (fpm-fcgi) (built: Jan 7 2011 00:07:27) lighttpd/1.4.28 (ssl) - a light and fast webserver PHP and vBulletin are configured to use memcached. MySQL Settings : [mysqld] key_buffer = 128M max_allowed_packet = 16M thread_cache_size = 8 myisam-recover = BACKUP max_connections = 1024 query_cache_limit = 2M query_cache_size = 128M expire_logs_days = 10 max_binlog_size = 100M key_buffer_size = 128M join_buffer_size = 8M tmp_table_size = 16M max_heap_table_size = 16M table_cache = 96 Other : From the cloud's IO chart, we're averaging 100mb/s read. > vmstat procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 9 0 73140 36336 8968 1859160 0 0 42 15 3 2 6 1 89 5 > /etc/init.d/mysql status Threads: 49 Questions: 252139 Slow queries: 164 Opens: 53573 Flush tables: 1 Open tables: 337 Queries per second avg: 61.302. moved from superuser

    Read the article

  • Internal Use Chat/Desktop Platform

    - by Malnizzle
    I did some looking, but I didn't see a SF question directly related to this. I need to find a platform for internal/LAN use only for chat and desktop sharing. We got a lot people having to get up and walk over to another person's office for simple items, and we could save a lot of time collectivity if we had a solution where we had a client app similar to gchat or AIM, where one could right click a name and request a desktop sharing session (to or from). This wouldn't be for product presentation or long training sessions, and wouldn't need more than 2 people in the session. We use GoToMeeting for this. I've looked at TeamViewer, and they got the features I want (plus a lot more features that wouldn't help) and seem more geared to large enterprise support, and it is not exactly cheap. Also looked at OCS some as well, but it seems heavy for what I am trying to do. I don't need anything relating to phone usage. If the general opinion says otherwise, I could talked back into OCS if I am wrong about weight of the product. We use GoToAssist for remote support of clients (which I am a fan of), and I don't it fits here, correct me if I am wrong. All the workstations are XP/7. Thanks!

    Read the article

  • How do I host multiple independent, secured SharePoint sites (WSS 3.0) without using Active Director

    - by Kyle Noland
    I have a SharePoint site set up on one of my networks to service Active Directory users. To be clear, this is a Windows SharePoint Services 3.0 installation running on Windows Server 2003 Standard. It is not an option to upgrade the server or SharePoint version. Management would like to create several new sites, one for each of a handful of clients. These sites will be used like "dropboxes" or FTP sites so that my company can make large files available to outside contacts, and vice versa. Here are my requirements: I do not want to have to create Active Directory accounts for each external contact. If possible, I would like to store the external usernames and passwords in a database that I can write a small GUI for so that management can handle adding their own external contacts. Each client site must be sandboxed from each other and from my main company SharePoint site. I would like to keep everything running on port 80 and be able to access the sites as either clientname.mycompany.com or www.mycompany.com/clientname If anybody has ever done this I would really appreciate hearing about any lessons you learned and suggestions for how to set this up. Kyle

    Read the article

  • Solaris TCP stack tuning

    - by disserman
    We have a large web project (about 2-3k requests per second), using haproxy (http://haproxy.1wt.eu/) as a frontend and load balancer between the java application servers. The frontend (haproxy) is running on Linux but we are going to migrate it to the Solaris 10 as all our other servers are running under Solaris. After switching a traffic I see the two things: a) the web site became loading slower (5-10 seconds with images in comparison to 2-3 seconds on Linux) b) sometimes haproxy fails to perform a "lifecheck" (get a special web page and analyze http response code) due to the socket timeout. After switching traffic back to Linux everything is okay. I've tried to tune all params I found in /dev/tcp but no progress. I believe the problem is in some open socket limitations. If someone can point me to the answer, I would be greatly appreciated. p.s. haproxy is running under Xen DomU on Linux (Kernel 2.6.18, Debian 5), under zone on Solaris (10 u8). the only thing we did on Linux is increasing of ip_conntrack_max (I believe Solaris option tcp_conn_req_max_q is the equivalent).

    Read the article

  • Network Management Cable Labeling Techniques and their alternatives [closed]

    - by Alex
    Possible Duplicate: What is the most effective solution you used to label cables? Yes i know there are a lot of howtos and already answered questions about this topic, like this one: How do you organise the cables in your racks? Currently i am searching the web for different techniques (alternatives) for labeling the cables at the server racks and/or data centers. Unfortunately i do not have any experience with labeling/documentation of network cables in a large scale. As far as I could lookup by now the current labeling techniques are coloring and a self defined print-labeling technique (numbering, text) maybe also according to a standard which are usually used. I want to know if QR, RFID (ok RFID in a data center would be stupid due to the radio frequency wouldn't it be?), Barcodes or similar (??) have already been used by some administrators or why they did not consider such techniques at all? Too complicated (with QR scanner etc..) if you are in front of the cables and want to get quick feedback for what the cable is? What alternatives are out there? Advantages/Disadvantages? Best-Practice? I would appreciate any help on this topic, thank you! Regards, Alex

    Read the article

  • iptables (NAT/PAT) setup for SSH & Samba

    - by IanVaughan
    I need to access a Linux box via SSH & Samba that is hidden/connected behind another one. Setup :- A switch B C |----| |---| |----| |----| |eth0|----| |----|eth0| | | |----| |---| |eth1|----|eth1| |----| |----| Eg, SSH/Samba from A to C How does one go about this? I was thinking that it cannot be done via IP alone? Or can it? Could B say "hi on eth0, if your looking for 192.168.0.2, its here on eth1"? Is this NAT? This is a large private network, so what about if another PC has that IP?! More likely it would be PAT? A would say "hi 192.168.109.15:1234" B would say "hi on eth0, traffic for port 1234 goes on here eth1" How could that be done? And would the SSH/Samba demons see the correct packet header info and work?? IP info :- A - eth0 - 192.168.109.2 B - eth0 - 192.168.109.15 - eth1 - 192.168.0.1 C - eth1 - 192.168.0.2 A, B & C are RHEL (RedHat) But Windows computers can be connected to the switch. I configured the 192.168.0.* IPs, they are changeable. Any help?

    Read the article

< Previous Page | 545 546 547 548 549 550 551 552 553 554 555 556  | Next Page >