Search Results

Search found 18598 results on 744 pages for 'result'.

Page 549/744 | < Previous Page | 545 546 547 548 549 550 551 552 553 554 555 556  | Next Page >

• Recovering drive via boot to Win7 setup command prompt

  - by Valamas

  I am trying to recover data from two old IDE drives. Drive1 has been successful, but something is wrong with Drive2. It does not appear as a drive letter. Due to limited legacy hardware, the only way i can see these drives is to boot using windows 7 setup and goto the command prompt. Without going further as to why, my question is how i can access the data in this command prompt. I discovered DISKPART command and while a first time user, it looked like something that can fix my problem. Here are the results of my diskpart commands. At the bottom is a image of the commands taken with a camera. The Drive2 is present because when using the diskpart command, I can see it. How can I copy the information using a robocopy script if the drive letter is not available? how can I assign a drive letter? Is there any repair command I need to execute? When i execute DISKPART, the following is what i see. DISKPART> LIST DISK Disk### Status Size Free Disk 5 Online 37 GB 2048 KB So then I select disk 5. DISKPART> SELECT DISK 5 "Disk 5 is now the selected disk" When I list partition DISKPART> LIST PARTITION Partition ### Type Size Partition 1 Primary 101 MB Partition 2 Primary 37 GB So I select partition 2 "Partition 2 is now the selected partition." I then try to assign a drive letter DISKPART> ASSIGN LETTER=G "There is no volume specified." "Please select a volume and try again." When i list volume the drive is not present. DISKPART> LIST VOLUME Result of the above commands

  Read the article

• .tex file remains in use by process when batch file is triggered by .Rnw Sweave processing.

  - by drknexus

  This is a pretty specialized question. I'm using the Eclipse IDE in a Windows XP environment with the StatET plug-in so I can write R code as an R/Sweave document. This produces a .tex file that is then post processed by pdflatex.exe. When I create the file as normal everything works great (except maybe my file named russfnc2.Rnw seems to result in russfnc.pdf even though pdflatex.exe on the console window correctly says that the output is being writen to russfnc2.pdf). The big problem is when I trigger a batch file from within my Rnw code. My goal here is to spawn a side process that waits for the PDF to be made and uploads it to the server. So the Rnw contains: if(file.exists("rsp.finalize.bat")) {system("rsp.finalize.bat",wait=FALSE,invisible=FALSE)} The batch file calls Rterm.exe to run a script: setwd("C:/theprojectdirectory") while(!file.exists("russfnc.pdf")) { Sys.sleep(1) } Sys.sleep(60) At the end of that script, I use a shell call to launch psftp.exe and upload the files. All of this works fine, when I use my Eclipse profile to trigger Sweave... that is unless I have that batch file at the end of the .Rnw. When it is located there, I get the error message pdflatex.exe: Permission denied: c:\thepath\thetexfile.tex. After that, the .tex file (as far as XP is concerned) is in use by another process and I have to reboot in order to delete it (and, of course, the pdf is not made). If I manually trigger the batch file after pdflatex.exe has done its things, everything works fine. How can I make this work correctly using the tools I'm familiar with vis., R and Dos-style batch files? I'm not sure if this is a SuperUser question or a StackOverflow question, so I'm starting here.

  Read the article

• IPv6 Routing / Subnetting

  - by nappo

  Recently I have installed Citrix Xen Server 6.2 on a machine. My Provider (Hetzner) gave me the IPv6 Subnet 2a01:4f8:200:xxxx::/64. Followed an article in the providers wiki (1) i got it working and can assign IPs to my guests (CentOS). However i can't assign a second IP to a single guest - it will result in a timeout. I'm not very familiar with IPv6 routing / subnetting - any help or tips for further troubleshooting is welcome! My Setup: XenServer 6.2 IPv6: 2a01:4f8:200:xxxx::2/112 ip -6 route: 2a01:4f8:200:xxxx::/112 dev xenbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 default via fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 Guest 1 IPv6: 2a01:4f8:200:xxxx::3/64 IPv6: 2a01:4f8:200:xxxx::4/64 ip -6 route: 2a01:4f8:200:xxxx::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via fe80::1 dev eth0 metric 1 mtu 1500 advmss 1440 hoplimit 4294967295 Guest 2 IPv6: 2a01:4f8:200:xxxx::5/64 Guest 1 IPv6 is working fine, Guest 2 too. As suggested by the wiki article (1) i split my /64 network into a /112. Is it right to set the host /112 and the guests /64? Why is that?

  Read the article

• Trouble with backslash characters and rsyslog writing to postgres

  - by Flimzy

  I have rsyslog 4.6.4 configured to write mail logs to a PostgreSQL database. It all works fine, until the log message contains a backslash, as in this example: Jun 12 11:37:46 dc5 postfix/smtp[26475]: Vk0nYDKdH3sI: to=<[email protected], relay=----.---[---.---.---.---]:25, delay=1.5, delays=0.77/0.07/0.3/0.35, dsn=4.3.0, status=deferred (host ----.---[199.85.216.241] said: 451 4.3.0 Error writing to file d:\pmta\spool\B\00000414, status = ERROR_DISK_FULL in "DATA" (in reply to end of DATA command)) The above is the log entry, as written to /var/log/mail.log. It is correct. The trouble is that the backslash characters in the file name are interpreted as escapes when sent to the following SQL recipe: $template dcdb, "SELECT rsyslog_insert(('%timereported:::date-rfc3339%'::TIMESTAMPTZ)::TIMESTAMP,'%msg:::escape-cc%'::TEXT,'%syslogtag%'::VARCHAR)",STDSQL :syslogtag, startswith, "postfix" :ompgsql:/var/run/postgresql,dc,root,;dcdb As a result, the rsyslog_insert() stored procedure gets the following value for as msg: Vk0nYDKdH3sI: to=<[email protected], relay=----.---[---.---.---.---]:25, delay=1.5, delays=0.77/0.07/0.3/0.35, dsn=4.3.0, status=deferred (host ----.---[199.85.216.241] said: 451 4.3.0 Error writing to file d:pmtaspoolB The \p, \s, \B and \0 in the file name are interpreted by PostgreSQL as literal p, s, and B followed by a NULL character, thus early-terminating the string. This behavior can be easiily confirmed with: dc=# SELECT 'd:\pmta\spool\B\00000414'; ?column? -------------- d:pmtaspoolB (1 row) dc=# Is there a way to correct this problem? Is there a way I'm not finding in the rsyslog docs to turn \ into \\?

  Read the article

• Why does Outlook 2007 lose connection to Exchange when Windows 7 64-bit turns off display?

  - by Greg R.

  The problem: When Windows 7 puts the display to sleep, Outlook 2007 and also Microsoft Office Communicator 2005 lose the connection to the Exchange server. When I unlock the computer, Outlook is logged out of Exchange and prompts me for credentials (although usually I have to restart Outlook to get it to reconnect). The network connection is still active, e.g. other applications don't lose their connection to the network or Internet when Windows 7 puts the display to sleep. I'm using a Dell E5400 notebook running Windows 7 Enterprise 64-bit with Outlook 2007 connecting to a corporate Exchange server (not sure if it's Exchange 2007 or 2010). The Dell is typically docked and connected via DVI (through the dock) to two Dell monitors. The Power Options in Windows 7 are set as follows: Turn Off The Display: 15 minutes Put The Computer To Sleep: never Those are the "Plugged In" settings but the problematic behavior is the same when running on battery. When Windows 7 turns off the display, it automatically locks the computer. E.g., I have to re-enter my credentials to access the machine. This is per corporate policy. The equivalent set up on my previous Dell notebook running Windows XP SP3 did not result in this problem with Outlook 2007 or Office Communicator 2005 connecting the very same exchange server. The problem began when I switched to the new Dell E5400 with Windows 7.

  Read the article

• Why does this rsnapshot exclude not work?

  - by bstpierre

  Rsnapshot passes excludes directly to rsync, but rsync's behavior appears inconsistent. I've simplified my rsnapshot backup test to the following directory tree (this tree will be backed up): gorilla:~# find /tmp/snaptest -exec file {} \; /tmp/snaptest: directory /tmp/snaptest/SKIPTHIS: directory /tmp/snaptest/SKIPTHIS/xyz: directory /tmp/snaptest/SKIPTHIS/xyz/testing: ASCII text /tmp/snaptest/SKIPTHIS/bar: ASCII text /tmp/snaptest/SKIPTHIS/foo: ASCII text /tmp/snaptest/SKIPTHIS.txt: ASCII text My config file: config_version 1.2 snapshot_root /tmp/backup-media no_create_root 1 cmd_cp /bin/cp cmd_rm /bin/rm cmd_rsync /usr/bin/rsync cmd_ssh /usr/bin/ssh cmd_logger /usr/bin/logger cmd_du /usr/bin/du interval hourly 6 interval daily 7 interval weekly 4 interval monthly 3 verbose 3 loglevel 3 logfile /media/maxtor-one-touch/rsnapshot.log lockfile /media/maxtor-one-touch/backups/.rsnapshot.pid rsync_short_args -a rsync_long_args --delete --numeric-ids --relative --delete-excluded exclude "SKIPTHIS/**" link_dest 1 backup /tmp/snaptest snaptest The result: gorilla:~# rsnapshot -c /tmp/snaptest.conf hourly echo 12638 > /media/maxtor-one-touch/backups/.rsnapshot.pid mkdir -m 0755 -p /tmp/backup-media/hourly.0/ /usr/bin/rsync -a --delete --numeric-ids --relative --delete-excluded \ --exclude="SKIPTHIS/**" /tmp/snaptest \ /tmp/backup-media/hourly.0/snaptest touch /tmp/backup-media/hourly.0/ rm -f /media/maxtor-one-touch/backups/.rsnapshot.pid gorilla:~# find /tmp/backup-media/ -exec file {} \; /tmp/backup-media/: directory /tmp/backup-media/hourly.0: directory /tmp/backup-media/hourly.0/snaptest: directory /tmp/backup-media/hourly.0/snaptest/tmp: sticky directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest: directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS: directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/xyz: directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/xyz/testing: ASCII text /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/bar: ASCII text /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/foo: ASCII text /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS.txt: ASCII text My confusion stems from the fact that if I copy-paste the rsync command echoed by rsnapshot, the SKIPTHIS directory is excluded! (I've tested with various other SKIPTHIS patterns with the same results.) Any idea what's going on?

  Read the article

• Command line scripts to restore the 4 system databases of MS SQL Server 2008

  - by ciscokid

  Hi there, can someone give me some advice on how to restore the 4 system databases (master, msdb, model, tempdb) of a sql server 2008 please? I've already done some testing myself (on restoring the master database) with the following commad line script as a result: ::set variables set dbname=master set dbdirectory=C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA title Restoring %dbname% database net stop mssqlserver cd C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\Binn sqlservr -m sqlcmd -Slocalhost -E -Q "restore database master from disk='c:\master.bak' WITH REPLACE" net start mssqlserver pause After the execution of the 'sqlservr -m' command (used to start the server instance in single-user mode, which is only necessary when restoring the MASTER database), the script stops. So in order to execute the last 2 commands I need to separate the script into 2 smaller scripts, and run them one after the other. Does anyone has an idea on how I can merge them into one single script that runs completely without any interruption? I also want to restore the other 3 system databases using command line scripts like this one. Can someone please advice me how I need to go on? I've already noticed that restoring the temdb is not so easy, but there has to be a way... Looking forward to your advice!

  Read the article

• WordPress permalinks not working, everything seems fine

  - by javipas

  I have a WordPress blog I've migrated from another CMS, and I've being having a lot of problems with my permalinks structure: lots of articles give a 404, although they are there, somewhere, published. The site is www.muycomputerpro.com (MCP for short), and for example an article that should be found is: http://muycomputerpro.com/Actualidad/Especiales/2009-las-grandes-crecen-en-la-bolsa If I do a search on the search tool at MCP, the result is there (see EnlacesMCP-1.jpg) But when I click on the link, our 404 error page appears (see EnlacesMCP-2.jpg) The weird thing is, the article is published, and the permalink is the right one, as you can see on this screenshot of the WordPress CMS: The permalink (below the title) is correct (http://www.muycomputerpro.com/Actualidad/Especiales/2009-las-grandes-crecen-en-la-bolsa/) but it does not work. In fact, if I try to use the short link (http://www.muycomputerpro.com/?p=5023) the article does not show either. I've accessed my WordPress DB and I've search the article to see if there is something wrong there, but from what I can tell all the fields are OK, here's a screenshot: I really don't know what is causing this. The permalink structure should work (I'm using the "Custom permalink" plugin to preserve the old URLs that had a alphanumeric code at the end of the postname) and the permalink config on wordpress is "/%postname%/". I really need help :(

  Read the article

• Error 0x80073cf9 when installing or updating apps from windows store

  - by cmorse

  On my Windows 8 desktop I keep getting error 0x80073cf9 when I try to install or update an app from the windows store. In the installings apps pane it just says "This app wasn't installed -- view details" and when I select that it says "Something happened and this app couldn't be installed. Please try again. Error code: 0x80073cf9" I am using the built-in windows firewall and antivirus. And my laptop is able to install updates when it is on the same network. This is what winstore.log shows when I try to update the maps app: 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] *********************************************************************** 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] Process name: C:\Windows\system32\taskhost.exe 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] User name: Desktop\User 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] Computer name: desktop 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] Windows build: 9200.16424.amd64fre.win8_gdr.120926-1855 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] Client version: 615 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011428] CWSTileUpdateHandler::Worker: Broker is handling badge updates. 2012-10-18 15:31:47.554, _Info_ WS [00002572:00008200] CProgressDispatcher::OnProgress: AppId = 97a2179c-38be-45a3-933e-0d2dbf14a142, PFN = Microsoft.BingMaps_8wekyb3d8bbwe, InstallPhase = 1, PhasePercent = 0, TotalPercent = 0 2012-10-18 15:31:47.558, _Warning_ WS [00002572:00008200] CDownloadProgress::IDownloadCompletedCallback::Invoke: Download complete result 0x80073cf9 for Microsoft.BingMaps_8wekyb3d8bbwe 2012-10-18 15:31:47.559, _Error_ WS [00002572:00008200] CActionItem::_DoDownload: Download failed for 97a2179c-38be-45a3-933e-0d2dbf14a142, hr=0x80073cf9 2012-10-18 15:31:47.560, _Info_ WS [00002572:00008200] CActionItem::_DoDownload: Notifying progress handlers of download failure for 97a2179c-38be-45a3-933e-0d2dbf14a142, hr=0x80073cf9 2012-10-18 15:31:47.560, _Error_ WS [00002572:00008200] CProgressDispatcher::OnError: PFN = Microsoft.BingMaps_8wekyb3d8bbwe, InstallPhase = 1, hrError = 0x80073cf9

  Read the article

• Browser says "Waiting for www.xyz.com" for a very long time

  - by Phil

  When I load my website (hosted with Ipage). The browser often takes an incredible long time saying "Waiting for www.xyz.com ..." before any elements of the site actually appear. After this "Waiting for" process, the text, images and everything else actually load quite fast. I contacted my host with my tracert result and they said they optimized my website database and increased the memory available to PHP on my account to 64 Mb.They also said they have checked the issue by accessing my website and found that it is loading fine without any slowness. It seems to be a temporary issue. Please try to access your website with different browser and network. I tried different browsers and networks but this "Waiting for" process always takes too long. My website is http://www.surreyextra.com/ . It's Wordpress and BuddyPress. I'm in the UK while Ipage host is placed in the USA, can this potentially be a problem? I have tried a number of optimizations, like minifying my CSS and JS files and use catching but the problem hasn't improved. So is it my host's fault, should I contact them again?

  Read the article

• Migrating to Windows Server 2008 R2 Domain Controllers - a few Questions/Issues

  - by Chris

  Ok so here's our setup: We have 2 Windows 2003 Domain Controllers. I am trying to replace them with Windows 2008 R2. The 2003 servers are named DC01 and DC02. The 2008 R2 servers are DC1 and DC2. I prepared the Windows Server 2003 Forest Schema for a Domain Controller that runs Windows Server 2008 or Windows Server 2008 R2. Then with both of the new servers up as member servers I ran dcpromo on DC1 using the advanced option and added it successfully to my existing domain. It's roles are GC, DNS and Active Directory Domain Services. I transferred The PDC Emulator, RID Pool Manager, and Infrastructure Master roles to DC1. The Schema Master and Domain Naming master are still on DC01. The first issue that I'm encountering is when I dcpromo the DC2 and select "Replicate data over the network from and existing domain controller" I select that I want to replicate from DC1 and I get the following error: Failed to identify the requested replica partner (dc1.xxx.org) as a valid domain controller with a machine account for (DC2$). This is likely due to either the machine account not being replicated to this domain controller because of replication latency or the domain controller not advertising the Active Directory Domain Services. Please consider retrying the operation with \dc01.xxx.org as the replica partner. "The server is unwilling to process the request. Is this because the Schema Master and Domain Naming Master roles are still on the old DC01? And if so, if I transfer Schema Master and Domain Naming Master roles to DC1 what is the risk or breaking my AD? I'm a little paranoid because this process HAS to be transparent. ANY down time or interruption will result in me getting a verbal ass kicking from my I.T. Director. Both of the new servers DNS point the the old DNS servers (DC01 and DC02) not themselves by the way.

  Read the article

• Problem routing between directly connected Subnets w/ ASA-5510

  - by Zephyr Pellerin

  This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

  Read the article

• linux: mount old ATA disk to USB adapter

  - by 130490868091234

  I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic Corp. SL11R-IDE IDE Bridge (04ce:0002), an ATA adapter to USB 1.0 like the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. I get different devices under, for example: /dev/bus/usb/003/002 or /dev/bus/usb/002/004, but I don't get any /dev/sdbN links. The output blkid -o list -c /dev/null is just the laptop's partitions. I have tried taking out the jumper, putting it as master and as CS Enabled, but didn't change the result. Any ideas?

  Read the article

• Problem in accessing Windows shared folder on Ubuntu using terminal

  - by vikramtheone

  Hi Guys, Description I have 2 systems with me, one running on Windows(Host) and one on Ubuntu, both on a LAN. On the Windows(Host) I develop software intended for the Linux system and because the Linux system has little external memory, my idea to overcome this is by making the project folder on the Host side a Shared Folder with full access and access it on Ubuntu over the network. To achieve this, I have installed Samba on Ubuntu, when I go to Places -> Network I can see the shared project folder and I simply mount it. A link appears on the desktop. Next, using Nautilus I open the link and I can access the contents of the shared folder. Problem Even though I mount the shared project folder, I don't see it appearing in the /media or the /mnt folder, as a result of this I don't know what path to use to access this folder, from the terminal. For example: When, I mounted my USB stick, as expected, a link for the device appears on the Desktop and I also see a folder in the media folder. So, similarly, a mounted shared folder should have appeared on the /mnt folder, too. Can anyone suggest what I should do now? There are many posts around, but no solid solution for this problem. Help!!! :) Vikram

  Read the article

• nginx config woes for multiple subdomains & domains

  - by Peter Hanneman

  I'm finally moving away from Apache and I've got the latest development version of nginx running on a fully updated Ubuntu 10.04 VPS. I've got a single dedicated IP for the box (1.2.3.4) but I've got two separate domains pointing to the server: www.example1.com and www.example2.net. I would like to map the fallowing relationships between urls and document roots in the config: www.example1.com / example1.com -> /var/www/pub/example1.com/ subdomain.example1.com -> /var/www/dev/subdomain/example1.com/ www.example2.net / example2.net -> /var/www/pub/example2.net/ subdomain.example2.net -> /var/www/dev/subdomain/example2.net/ Where the name of the requested subdomain is a folder under /var/www/dev/. Ideally a request for a non-existent subdomain(no matching folder found) would result in a rewrite to the public site (eg: invalid.example1.com -- www.example1.com) however a mere "404 Not Found" wouldn't be the worst thing in the world. It would also be nice if I didn't need to modify the config every time I mkdir a new subdomain folder - even better if I don't need to edit it for a new domain either...but now I'm getting greedy... :p Although in my defense Apache did all of this with a single directive. Does anyone know how I can efficiently mimic this behavior in nginx? Thanks in advance, Peter Hanneman

  Read the article

• EMC VNX iSCSI setup - unsure about SP/port assignment

  - by pauska

  We have a new VNX5300 waiting to get configured, and I need to plan out the network infrastructure before the EMC tech arrives. It has 4x1gbit iSCSI per SP (8 ports in total), and I'd like to get the most out of the performance until we jump over to 10gig iSCSI. From what I can read from the docs - the recommendation is to use only two ports per SP, with 1 active and 1 passive. Why is this? It seems kind of pointless to have quad-port i/o-modules and then recommend to not use more than two of them? Also - I'm a bit unsure about the zoning. The best practices guide state that you should separate each port on each SP from each other on different logical networks. Does this mean that I have to create 4 logical networks to be able to use all 8 ports? It also gives the following example: Does this mean that A0 and B0 should sit on the same physical switch aswell? Won't this make all traffic go on one switch (if both A1 and B1 are passive)? Edit: Another brainpuzzle I don't get it - each host (as in server) should not have more iSCSI bandwidth available than the storage processor. What on earth does this matter? If serverA have 1gbit and serverB have 100mbit, then the resulting bandwith between them is 100mbit. How can this result in some kind of oversubscription? Edit4: Wait, what. Active and passive ports? The VNX runs in a ALUA configuration with asymmetrical active/active.. there shouldn't be any passive ports, only preferred ones..

  Read the article

• fail2ban regex working but no action being taken

  - by fpghost

  I have the following snippet of fail2ban configuration on Ubuntu 13.10 server: #jail.conf [apache-getphp] enabled = true port = http,https filter = apache-getphp action = iptables-multiport[name=apache-getphp, port="http,https", protocol=tcp] mail-whois[name=apache-getphp, dest=root] logpath = /srv/apache/log/access.log maxretry = 1 #filter.d/apache-getphp.conf [Definition] failregex = ^<HOST> - - (?:\[[^]]*\] )+\"(GET|POST) /(?i)(PMA|phptest|phpmyadmin|myadmin|mysql|mysqladmin|sqladmin|mypma|admin|xampp|mysqldb|mydb|db|pmadb|phpmyadmin1|phpmyadmin2|cgi-bin) ignoreregex = I know the regex is good, because if I run the test command on my access.log: fail2ban-regex /srv/apache/log/access.log /etc/fail2ban/filter.d/apache-getphp.conf I get a SUCCESS result with multiple hits, and in my log I see entries like 187.192.89.147 - - [13/Apr/2014:11:36:03 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 301 585 "-" "-" 187.192.89.147 - - [13/Apr/2014:11:36:03 +0100] "GET /phpMyAdmin/scripts/setup.php HTTP/1.1" 301 593 "-" "-" Secondly I know email is configured correctly, as each time I service fail2ban restart I get an email for each of the filters stopping/starting. However despite all this no action seems to be taken when one of these requests comes in. No email with whois, and no entries in iptables. What possibly could be preventing fail2ban from taking action? (everything looks in order in fail2ban-client -d and I can see the chains have loaded with iptables -L)

  Read the article

• Install VirtualBox on Ubuntu 12.04.1 (on [Samsung] Chromebook)

  - by iphonedev7

  I have dual booted Ubuntu Linux 12.04.1 LTS on my Samsung Series 5 ChromeBook, and am trying to run/install Oracle VirtualBox (from the generic .run file downloaded from their website). However, every time I try to run it (as root from the command line), it gives me the following error occurs: Please install the build and header files for your current Linux kernel. The current kernel version is 3.4.0 Problems were found which would prevent VirtualBox from installing. I have tried the version from the Software Center, as well as the command line installation, both of which gave me errors based on my linux-headers/linux-kernel/linux-[kernel]-image. Here's an error I keep getting (on the command line): First Installation: checking all kernels... It is likely that 3.4.0 belongs to a chroot's host Building only for 3.5.0-18-generic Building initial module for 3.5.0-18-generic ERROR (dkms apport): kernel package linux-headers-3.5.0-18-generic is not supported Error! Bad return status for module build on kernel: 3.5.0-18-generic (x86_64) Consult /var/lib/dkms/virtualbox/4.1.12/build/make.log for more information. Setting up virtualbox-qt (4.1.12-dfsg-2ubuntu0.2) ... Processing triggers for libc-bin ... ldconfig deferred processing now taking place ...And one of the more cryptic errors I get when trying to start any Virtual Machine: Result Code: NS_ERROR_FAILURE (0x80004005) Component: Machine Interface: IMachine {5eaa9319-62fc-4b0a-843c-0cb1940f8a91}

  Read the article

• What is the best way to recover from a mysql replication fail?

  - by Itai Ganot

  Today, the replication between our master mysql db server and the two replication servers dropped. I have a procedure here which was written a long time ago and i'm not sure it's the fastest method to recover for this issue. I'd like to share with you the procedure and I'd appreciate if you could give your thoughts about it and maybe even tell me how it can be done quicker. At the master: RESET MASTER; FLUSH TABLES WITH READ LOCK; SHOW MASTER STATUS; And copy the values of the result of the last command somewhere. Wihtout closing the connection to the client (because it would release the read lock) issue the command to get a dump of the master: mysqldump mysq Now you can release the lock, even if the dump hasn't end. To do it perform the following command in the mysql client: UNLOCK TABLES; Now copy the dump file to the slave using scp or your preferred tool. At the slave: Open a connection to mysql and type: STOP SLAVE; Load master's data dump with this console command: mysql -uroot -p < mysqldump.sql Sync slave and master logs: RESET SLAVE; CHANGE MASTER TO MASTER_LOG_FILE='mysql-bin.000001', MASTER_LOG_POS=98; Where the values of the above fields are the ones you copied before. Finally type START SLAVE; And to check that everything is working again, if you type SHOW SLAVE STATUS; you should see: Slave_IO_Running: Yes Slave_SQL_Running: Yes That's it! At the moment i'm in the stage of copying the db from the master to the other two replication servers and it takes more than 6 hours to that point, isn't it too slow? The servers are connected through a 1gb switch.

  Read the article

• No video signal at boot with custom built computer

  - by Bart Pelle

  After booting my custom built computer, neither the VGA nor the HDMI methods from the video card seem to emit any signal to the display. I have tested both a regular VGA screen and a modern HDMI screen. Both did not receive signal. Below are the specifications from my computer build: Intel Core i5 3350P ASRock B75 Pro 3-M Seagate Barracuda 7200.14 ST1000 DM003 1000GB Corsair Vengeance LP CML 8GX 3M2 A1600 CGB Blue (2 cards) Cooler Master B Series B600 Club 3D Radeon HD7870 XT Jokercard Samsung SH-224 BB Black Sharkoon T28 Case The motherboard does not emit any beeps on startup. The CD tray opens properly and all fans spin. All cables are properly connected. All components are new and no damage was found on any of the components. The fans on the GPU spin aswell. The VGA test we did was by using the onboard graphics from the Intel i5, but this gave no result. The HDMI test was from the GPU which did not emit any signal either. We have not been able to test out the DVI, could this be important to test, even though all the other methods did not work? Thank you for your time and hopefully reply.

  Read the article

• Handling the Outlook 2007 AutoArchive PST file

  - by Doug Luxem

  We encourage our users to enable AutoArchive in Outlook 2007 as a way to manage their mailbox sizes. However, we frequently end up running in to problems with the archive.pst file that is generated. The two main problems we have are: The archive.pst file is located in the user's local profile directory and is never backed up. A dead hard drive or stolen laptop could result in months or years of missing email. All other personal data is stored on network shares, but we can't do that for Outlook PST files. Without some sort of manual intervention, the archive will grow to enormous sizes. Although Outlook 2007 SP2 handles the large files better than before, it still results in slow response times from Outlook and an increase likelihood of a corrupt PST file. To mitigate these problems personally, I move the archives to a c:\Outlook folder and manually back that up to a shared drive every month or so. Additionally, I rotate archive files every year so that I have one file for each year (archive2008.pst, etc). Obviously, asking our users to do this same wouldn't help much. We need some sort of automated solution to take care of points 1 and 2. I have to imagine this is a common problem for Exchange organizations, so what is the best method to handle this?

  Read the article

• Turn Excel spreadsheet into a formula

  - by ?????? ??????????

  I have an Excel spreadsheet that has a complex computation that is not trivial to turn into a macro or a single-cell formula. The spreadsheet has a about 10 different inputs (values a human enters in different cells of the spreadsheet) and then it outputs 5 independent calculations (in different 5 cells) based on that input. There calculation is using some pre-entered data in the spreadsheet (about 100 different constants) and doing some look-ups on them. Now I would like to use this whole spreadsheet as a formula on a different spreadsheet to calculate a set of input values and produce the corresponding set of output values. Imagine this as creating different table with 10 columns for the input variables and 5 columns for the outputs, then copying each input into the other spreadsheet and copying back the output in the results table. For instance: - A1, A2, A3,... A10 are cells where someone enters values - through a series of calculations B1, B2, B3, B4 and B5 are updated with some formulas Can I use the whole series of calculations from A1..A10 into B1..B5 without creating one massive huge formula or a VBA macro? I want to have a set of input values in 100 rows from A100, B100, C100,... J100 onward. Then do some Excel magic that will: 1. copy the values from A100...J100 into A1 to A10 2. wait for the result to appear in B1 to B5 3. copy the values from B1 to B5 into K100 to O100 4. repeat steps 1 to 3 for all rows from 100 to 150

  Read the article

• Outlook Signature Broken in Entourage

  - by Eric J.

  Some of our company uses Windows with Outlook 2010, and the rest use Mac with Entourage. When our standard signature line is included in an email that goes to Entourage, the result does not display correctly. It appears that Entourage is mangling the HTML. My working theory is that Entourage encounters inline CSS styles it does not know about and stops processing styles, but I'm really not sure. Question: How can I enter a signature into Outlook 2010 that will render correctly in Entourage? For example, can I specify somehow the exact HTML to use? Here's an example of how the HTML is being changed. Original on Outlook, as received by another Outlook client: <span style='font-size:9.0pt;font-family:"Century Gothic","sans-serif"; color:#1785C5'>My Company<br> </span></b><span class=apple-style-span><span style='font-size:9.0pt; font-family:"Century Gothic","sans-serif";color:#666666'>123 Main St.</span></span><span class=apple-style-span><span style='font-size:9.0pt;font-family:"Century Gothic","sans-serif"; color:#AFAFAF'>&nbsp;</span></span><span class=apple-style-span><span style='font-size:9.0pt;font-family:"Century Gothic","sans-serif";color:#666666'>Suite 100</span></span> Note the use of spans, color #1785C5 and color #666666. Same original email, as displayed in an Entourage client: <span style='font-size:9.0pt;font-family:"Century Gothic","sans-serif"; mso-fareast-font-family:"Times New Roman"'><br> <span style='color:#656565'>My Company<br> 123 Main St Suite 100<br> </span> Note the use of br tags rather than spans, and the color #656565.

  Read the article

• Cisco Access switch is dropping large amount of end points

  - by user135458

  This afternoon, with no changes to the network, a switch suddenly started dropping off lots of connections. These connections would come back up a few minutes later, then another area connected to the switch would drop off. This is an older 4006 chassis switch which could in and of itself be a problem but I'm looking to see what else you all would look for in trying to find a root cause. Switch is connected via ports 1/1 and 1/2 in an etherchannel to a VSS core 1/1/42 and 2/1/42. Both sides are up and working however the CPU on the switch will spike up to 99% and that's when CRC errors start to hit the VSS core on one of those interfaces and end points start dropping off. We tried new transceivers and SFP's on each side of the link, same result. When we tried swapping the fiber patch cables on the access switch the CRC errors did not follow the fiber cables they stayed with port 1/2 on the access switch. So port 1/2 on the supervisor module looks like the culprit. We actually tried to create a new member of the ethernet channel by taking a fiber media converter to cat5 and make that a member of the port-channel but when we plugged it in you couldn't even reach the switch. I'm guessing that's unrelated and a problem with the media converter. As of right now we have left it in a state of only one fiber cable running to one side of the VSS core (1/1 Access Switch -- 2/1/42). I've sent some info into TAC and they are looking into the situation but does anyone else have any commands I could run or some troubleshooting I could look into in the meantime?

  Read the article

• How to deploy website in IIS with a host name?

  - by Jayakumar

  I try to host my application in IIS. Below are the steps that I follow: Publish the code and place it in a path. Open IIS, right click on "sites" and select "Add Website". In that dialog I gave the site name and selected the app pool created for the application. I selected the physical path of the published code. I left the IP and port in the binding section without changes. and, finally, gave the host name as fus.km.com. When I try to browse the application the page is not Loading "Internet Explorer cannot display the Page" The machine domain is km.com UPDATE I tried to add the host name to the host file and flushed the DNS. The application asked for user credentials (I use windows Authentication in the application). But it did not login. On repeated tries it throws the error: HTTP Error 401.1 - Unauthorized You do not have permission to view this directory or page using the credentials that you supplied. I tried with different user to login but I get the same result.

  Read the article

< Previous Page | 545 546 547 548 549 550 551 552 553 554 555 556  | Next Page >