Search Results

Search found 10859 results on 435 pages for 'raid controller'.

Page 55/435 | < Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >

  • Drobo-like linux file server - how do I do it?

    - by John Hunt
    I've been pondering for a long time about how I can set up a server which operates much like the Drobo storage thing. The reasons I don't actually want a drobo is because I've heard scare stories, plus I'd like to do this on the cheap. So ideally I'm looking for something like lvm so I can create a logical volume that spans many hard disks of varying sizes... obviously that only offers redundancy if I put the LV on a raid array (as far as I know..) I have however been reading about technologies such as Microsoft's drive extender which duplicates files at the filesystem level and makes sure that the mirrored files are on a different phyiscal disk.. does anyone know or recommend a filesystem or method like this as it'll hopefully make much better use of the space available than raid ever could. Performance isn't an issue, I'd just really like to make the most of the hard disks I have lying around whilst having a bit of redundancy incase a disk dies. I understand full well that this is no replacement for a backup, but I'll only be storing files of medium importance and using the nas itself as a backup of my main pc and other systems. Thanks in advance! I'm hoping zfs or btrfs or something can do something clever for me :)

    Read the article

  • Converting software RAID1 to RAID10 for /boot

    - by luckytaxi
    Array info: /dev/md0 - /dev/sda1 and /dev/sdb1 /dev/md2 - /dev/sda2 and /dev/sdb2 Partition info: /boot - /dev/md0 / - /dev/md1 I have two drives that are setup as RAID1 using software RAID on Redhat. I added two additional drives (same size) and I would like to conver the RAID1 to a RAID10. The problem I'm having is adding the last drive to the array. I've gotten as far as creating a RAID10 with two missing devices but as soon as I add the last drive, all hell breaks loose. It seems /dev/sda1 is the culprit. What I'm not too sure about is how to create the RAID10. I've tried the following mdadm --create /dev/md2 --level=raid10 --raid-device=4 /dev/sdc1 missing /dev/sdd1 missing I then proceeded to fail /dev/sdb1 from /dev/md0 and added that partition to /dev/md2. I proceeded to install the MBR on EACH partition since boot resides on /dev/sdx1 on each drive. As a test, all is well, I'm able to boot back into the system once I do a quick reboot. Now, when I go add the last drive /dev/sda1, it breaks. I attempted to install grub on /dev/sda1 and I get the following ... grub> root (hd0,0) /dev/sda root (hd0,0) /dev/sda Filesystem type is ext2fs, partition type 0xfd grub> setup (hd0) setup (hd0) Checking if "/boot/grub/stage1" exists... no Checking if "/grub/stage1" exists... no Error 2: Bad file or directory type At this point, the array is hosed I believe. I rebooted the server and it refuses to boot.

    Read the article

  • Join multiple filesystems (on multiple computers) into one big volume

    - by jm666
    Scenario: Have 10 computers, each have 12x2TB HDDs (currently) in raidZ2 (10+2) configuration, so, in the each computer i have one approx. 20TB volume. Now, need those 10 separate computers (separate raid groups) join into one big volume. What is the recommended solution? I'm thinking about the FCoE (10GB ethernet). So, buying into each computer FCoE (10GB ethernet card) and - what need more on the hardware side? (probably another computer, FCoE switch? like Cisco Nexus?) The main question is: what need to install and configure on each computer? Currently they have freebsd/raidz2, but it is possible change it into Linux/Solaris if needed. Any helpful resource what talking about how to build a big volumes from smaller raid-groups (on the software side) is very welcomed. So, what OS, what filesystem, what software - etc. In short: want get one approx. 200TB storage (in one filesystem) from already existing computers/storage. Don't need fast writes, but need good performance on reading data. (as a big fileserver), what will works transparently, so when storing data don't want care about onto what computer the data goes. (e.g. not 10 mountpoints - but one big logical filesystem). Thanks.

    Read the article

  • How to force mdadm to stop RAID5 array?

    - by lucek
    I have /dev/md127 RAID5 array that consisted of four drives. I managed to hot remove them from the array and currently /dev/md127 does not have any drives: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdd1[0] sda1[1] 304052032 blocks super 1.2 [2/2] [UU] md1 : active raid0 sda5[1] sdd5[0] 16770048 blocks super 1.2 512k chunks md127 : active raid5 super 1.2 level 5, 512k chunk, algorithm 2 [4/0] [____] unused devices: <none> and mdadm --detail /dev/md127 /dev/md127: Version : 1.2 Creation Time : Thu Sep 6 10:39:57 2012 Raid Level : raid5 Array Size : 8790402048 (8383.18 GiB 9001.37 GB) Used Dev Size : 2930134016 (2794.39 GiB 3000.46 GB) Raid Devices : 4 Total Devices : 0 Persistence : Superblock is persistent Update Time : Fri Sep 7 17:19:47 2012 State : clean, FAILED Active Devices : 0 Working Devices : 0 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 512K Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 0 0 2 removed 3 0 0 3 removed I've tried to do mdadm --stop /dev/md127 but: mdadm --stop /dev/md127 mdadm: Cannot get exclusive access to /dev/md127:Perhaps a running process, mounted filesystem or active volume group? I made sure that it's unmounted, umount -l /dev/md127 and confirmed that it indeed is unmounted: umount /dev/md127 umount: /dev/md127: not mounted I've tried to zero superblock of each drive and I get (for each drive): mdadm --zero-superblock /dev/sde1 mdadm: Unrecognised md component device - /dev/sde1 Here's output of lsof|grep md127: lsof|grep md127 md127_rai 276 root cwd DIR 9,0 4096 2 / md127_rai 276 root rtd DIR 9,0 4096 2 / md127_rai 276 root txt unknown /proc/276/exe What else can I do? LVM is not even installed so it can't be a factor.

    Read the article

  • Creating a partitioned raid1 array for booting a debian squeeze system

    - by gucki
    I'd like to have the following raid1 (mirror) setup: /dev/md0 consists of /dev/sda and /dev/sdb I created this raid1 device using mdadm --create --verbose /dev/md0 --auto=yes --level=1 --raid-devices=2 /dev/sda /dev/sdb This gave a warning about metadata being 1.2 and my system might not boot. I cannot use 0.9 because it restricts the size of the raid to 2TB and I assume grub shipped with latest debian (squeeze) should be able to handle metadata 1.2. So then I created the needed partitions like this: # creating new label (partition table) parted -s /dev/md0 mklabel 'msdos' # creating partitions sfdisk -uM /dev/md0 << EOF 0,4096 ,1024,S ; EOF # making root filesystem mkfs -t ext4 -L boot -m 0 /dev/md0p1 # making swap filesystem mkswap /dev/md0p2 # making data filesystem mkfs -t ext4 -L data /dev/md0p3 Then I mounted the root partition, copied a minimal debian install inside and temporary mounted /dev /proc /sys. Afer this I chrooted to the new root folder and executed: grub-install --no-floppy --recheck /dev/md0 However this fails badly with: /usr/sbin/grub-probe: error: unknown filesystem. Auto-detection of a filesystem of /dev/md0p1 failed. Please report this together with the output of "/usr/sbin/grub-probe --device-map=/boot/grub/device.map --target=fs -v /boot/grub" to I don't think it's a bug in grub (so I didn't report it yet) but a fault of mine. So I really wonder how to properly setup my raid1, everything I tried so far failed.

    Read the article

  • Cannot get at data in my NAS

    - by Ben
    I've got a bit of an issue that I'm hoping you can help me with. I have an Iomega ix4 as my NAS. This runs Linux and each drive in the box has 2 partitions: one for the OS and RAID info, and the second for the actual data. I had it configured as RAID5. Recently one of the drives failed. At this point all of the data was available, it was just reporting a failed drive. I had a drive of the same capacity (although not the exact same spec) which I swapped in place of the failed drive. It recognised it, and started to rebuild the data protection. So far so good ... or so I thought. The next day, after data protection had finished reconstructing, the NAS was telling me that 4 new drives had been added, and wanted confirmation to overwrite the data. Obviously I declined to do this. I swapped the failed drive back in again, in the hope that it would return to its previous state of the data being accessible, but one failed disk. However it didn't - it still tells me that the NAS has 4 new drives in it. I am hopeful that the actual data is untouched, so what I need to do is get it to rebuild the RAID without touching the data on the disks. I have ssh access, and have run stuff like mdadm --examine to see what I can find. The mdadm.conf file has no entry in the "definitions of existing MD arrays" section. I have not run any actual rebuilding commands as yet, because this is entering an area which I am out of my depth in. Please can someone advise the best way of getting my data? Thanks.

    Read the article

  • Stop Windows 7 from accessing or writing to hard drive unless "told" to by me? (More info inside...)

    - by Jeff
    A confusing question, perhaps, but bear with me. I have two internal HDDs set up in a RAID0 array which I use as mass storage. I access the drive very infrequently (once a day at most) and so I have set up Windows 7's power options to turn off idle disks after only 1 minute. This is fine, and the disks are turned off most of the time. However, I notice that Windows sometimes spins up the drives when I really, really don't want or need it to. This causes a 30 second delay as both drives spin up and lock up my system. Some examples of when this happens: 1) When I'm installing something using Windows Installer or Installshield; it seems to me as if they're using the drive with most available free space as the installer cache location... so my big RAID drive has to spin up! Most annoying. 2) Apparently, when I open a Java-based program which resides on my system drive and has nothing to do with my RAID drive! 3) At boot-up and shut-down time. At shutdown the drive spin up only for the computer to immediately shut down! Incredibly frustrating! I've already tried changing the letter of the drive, and at some points have removed the drive letter entirely, which solves the first two issues above. So my question (FINALLY!) is this: is there any way I can mark this drive as being for "storage only", so Windows basically does not see it at all until I actually invoke it somehow? Or is there any way I could set it up so that only specific programs have write access to it? For example, download managers, TeraCopy, etc. etc.? Basically I want it to be a "ghost drive" until I'm ready to use it and to stop Windows from spinning it up all the damn time! Thank you. :)

    Read the article

  • Replicated filesystem and EC2 MySQL

    - by El Yobo
    I'm currently investigating migrating our infrastructure over to run on Amazon's EC2 and am trying to figure out the best way to set up a MySQL service. I'm leaning towards running our own MySQL instances, rather than going with Amazon's RDS, but am still considering the best approach for performance and cost on the instance itself. In order to have persistent data, the MySQL data needs to be on an EBS volume (with some form of striped RAID, e.g. RAID0 or RAID10) to improve persistence. However, EBS IO is limited by the network interface (gigabit, so a theoretical maximum of 128 MB/s), while the ephemeral volumes have no such problem. I did see a suggestion for running two MySQL servers on an instance, with a master running on the ephemeral disk (which we would also RAID) and a slave storing changes to an EBS volume, but this has some additional overhead and complexity (two servers). What I was imagining is using some form of replicated file system such that I could have a filesystem on top of a RAID0 of ephemeral volumes to maximise performance all changes from the above immediately replicated to another RAID1 volume backed by multiple EBS volumes to ensure no data loss The advantages of this would be best possible IO performance for the DB server; no network delay in IO decreased IO on EBS volumes (as all read IO will be done on the ephemeral volumes) so decreased cost good data security, as it's backed onto redundant EBS volumes However, I haven't seen an appropriate system to replicate all changes from one volume to the other; is there a filesystem, or any other approach, which will do this? The distributed file systems, e.g. GlusterFS, DRBD etc seem to focus on replicating disks between servers, can they be set up to do what I'm interested in here? I also haven't seen anything about other's taking this approach. Do I have a solution in need of a problem here (i.e. is performance good enough, so this whole idea is redundant)? Is there some flaw in the plan?

    Read the article

  • 20 1TB drives vs. 10 2TB drives in RAID5/6 server

    - by Hunter
    Hi everyone, I will be setting up a server at work and I need some advice on some details. The setup will be one blade-type server (8-core, 16GB RAM) with two subsystems - one for the main storage the other to back it up. I'm shooting for a 20TB array (I know it'll be less after formatting and parity drives). So is there any advantage one way or the other with either 20 1TB drives or 10 2TB drives? I'm not sure right now how many controllers I should have either (in the quote I have is a dual-port controller). I would think two controllers for a server of this size would be a better choice than the dual-port controller (but I really don't know). And would an array of this size have any performance issues in RAID 5 or 6 (I know RAID 5 or 6 are "slower" because of all the parity calculations). Also, these will be either WD RE3 (1TB) or the RE4 (2TB). Oh, also, for the backup array would it be ok to use the WD 2TB green drives (also in RAID5 or 6)?

    Read the article

  • mdadm lvm and ext4 slowness - How can I speed it up?

    - by beatbreaker
    I can't figure out why I'm getting such terrible times out of my mdadm and in particular the lvm partitions in it. I made the raid: mdadm --create --verbose /dev/md0 --level=5 --chunk=1024 --raid-devices=4 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 # cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md0 : active raid5 sda1[0] sdd1[3] sdc1[2] sdb1[1] 2930279424 blocks level 5, 1024k chunk, algorithm 2 [4/4] [UUUU] I then created the physical volume, volume group, and logical volumes, I then formatted the logical volumes to ext4 using the following commands I got from here: http://busybox.net/~aldot/mkfs_stride.html mkfs.ext3 -b 4096 -E stride=256,stripe-width=768 /dev/datavg/blah Now I'm confused, I had these lvs running real quick before in mdadm but now that I've 'optimized' everything it's slower, eg, before: /dev/datavg/lv_audio: Timing buffered disk reads: 598 MB in 3.01 seconds = 198.85 MB/sec but now after: /dev/datavg/audio: Timing buffered disk reads: 198 MB in 3.00 seconds = 65.96 MB/sec That's pitiful! What's happened here? Did I not follow the instructions correctly? Can i reshape the ext4 partitons to default back to what they were? (I used defaults before and they were fine!)

    Read the article

  • Install server 2012 on HP ML110 G7 with B110i controller, no disks found

    - by Molotch
    I'm trying to install Server 2012 on a HP ML110 G7 with a B110i controller and four non hot-swappable SATA drives. I just can't get the Server 2012 boot disk PE environment to find any disks. I have downloaded the latest SPP (Service Pack for Proliant 2012.10) and flashed the BIOS. I have tried two different HP drivers for B110i and Windows X64, 6.18.0.64 and 6.18.2.64 to no avail. I have tried setting the controller to both AHCI and legacy mode in the BIOS, no difference. HP:s SmartStart disc for G7 servers only support installation of up to Windows Server 2008R2. HP:s installation instructions for Server 2012 Essentials says boot from the windows disk and use the storage drivers found on the SPP (I can't find any storage drivers on the SPP disk).

    Read the article

  • HyperV on Domain Controller or DC on HyperV?

    - by Michael Stum
    I want to setup a little fileserver/domain controller/sharepoint server. SharePoint shouldn't run on the DC directly, so I want to use HyperV. But I never used it before, so I wonder: Should I install the Domain Controller and HyperV Role and run 1 VM for SharePoint? Or should I run HyperV server and then 2 servers, one for SharePoint and 1 for DC? Usage is minimal with only 1 user. Hardware will be an Athlon II X3 with 3x2.9 GHz and 4 GB RAM. Operating System will be Server 2008 R2 Standard in all cases.

    Read the article

  • HP SmartArray P400 has slow read and write speed

    - by Tadas D.
    I have desktop in which I installed HP SmartArray P400 controller with two HP DF0146B8052 hard drives. I made RAID0 logical volume from them, but I am getting 20MB/s write speed and ~140-120MB/s read speed. Also there is quite low scatter for benchmark results (I am getting quite nice line) and it looks like controller is "capping" my speeds. I tried reseting controllers configuration and I haven't found any settings in HP ACU (Array Configuration Utility) to help me. I am using Windows 7 Ultimate and M4A78 board Does anyone have ideas what could be wrong? Also I am attaching diagnostic results.

    Read the article

  • Where to use Controller.HttpContext

    - by Ben
    Hi, In my base controller's constructor I am calling an extension method that checks for specific cookies on the client. Currently I am using System.Web.HttpContext.Current to get the current context. However, I am lead to believe that I should be using Controller.HttpContext since it is more testable and contains additional information about the request. However, Controller.HttpContext returns null on creation (believe this is by design) but also on Initialize and Execute methods (unless I use Routing.RequestContext.HttpContext?). So if I should be using Controller.HttpContext instead of HttpContext.Current, at what point is it available to me in a request? Thanks Ben

    Read the article

  • Cannot exclude a path from basic auth when using a front controller script

    - by Adam Monsen
    I have a small PHP/Apache2 web application wherein I'd like to do two seemingly incompatible operations: Route all requests through a single PHP script (a "front controller", if you will) Secure everything except API calls with HTTP basic authentication I can satisfy either requirement just fine in isolation, it's when I try to do both at once that I am blocked. For no good reason I'm trying to accomplish these requirements solely with Apache configuration. Here are the requirements stated as an example. A GET request for this URL: http://basic/api/listcars?max=10 should be sent through front.php without requiring basic auth. front.php will get /api/listcars?max=10 and do whatever it needs to with that. Here's what I think should work. In my /etc/hosts I added 127.0.0.1 basic and I am using this Apache config: <Location /> AuthType Basic AuthName "Home Secure" AuthUserFile /etc/apache2/passwords require valid-user </Location> <VirtualHost *:80> ServerName basic DocumentRoot /var/www/basic <Directory /var/www/basic> <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{SCRIPT_FILENAME} !-f RewriteCond %{SCRIPT_FILENAME} !-d RewriteRule ^(.*)$ /front.php/$1 [QSA,L] </IfModule> </Directory> <Location /api> Order deny,allow Allow from all Satisfy any </Location> </VirtualHost> But I still always get a HTTP 401: Authorization Required response. I can make it work by changing <Location /api> into <Location ~ /api> but this allows more than I want to past basic auth. I also tried changing the <Directory /var/www/basic> section into <Location />, but this doesn't work either (and it results in some strange values for PATH_TRANSLATED being passed to the script). I searched around and found many examples of selective exclusion of basic auth, but none that also incorporated a front controller. I could certainly do something like handle basic auth in the front controller, but if I can have Apache do that instead I'll be able to keep all authentication logic out of my PHP code. A friend suggested splitting this into two vhosts, which I know also works. This used to be two separate vhosts, actually. I'm using Apache 2.2.22 / PHP 5.3.10 on Ubuntu 12.04.

    Read the article

  • Restart Fibre channel controller after blade bootup IBM HS bladecentre

    - by Spence
    I have a remote system that needs to resume on startup. If the system is simply powered on then the blades boot before the SAN is online and then the only thing you can do is restart the systems. Is it possible to restart the fibre channel controller? That way I could have a system restart the controller after boot, connect to the SAN and then restart all servers requiring SAN information? Please note that I'm not a sys admin, just shooting for ideas to get a clean startup to work, apologies if my terminology is wrong.

    Read the article

  • Custom IIdentity and passing data from an attribute to a controller

    - by DM
    Here's my scenario: I've successfully created a custom IIdentity that I pass to a GenericPrincipal. When I access that IIdentity in my controller I have to cast the IIdentity in order to use the custom properties. example: public ActionResult Test() { MyCustomIdentity identity = (MyCustomIdentity)User.Identity; int userID = identity.UserID; ...etc... } Since I need to do this casting for nearly every action I would like to wrap this functionality in an ActionFilterAttribute. I can't do it in the controller's constructor because the context isn't initialized yet. My thought would be to have the ActionFilterAttribute populate a private property on the controller that I can use in each action method. example: public class TestController : Controller { private MyCustomIdentity identity; [CastCustomIdentity] public ActionResult() { int userID = identity.UserID; ...etc... } } Question: Is this possible and how? Is there a better solution? I've racked my brain trying to figure out how to pass public properties that are populated in an attribute to the controller and I can't get it.

    Read the article

  • Intel 520 SSD drives not working with lsi controller on VMware esxi 5

    - by Michael
    We have a problem with our LSI 9266 controller. LSI have vmware drivers which normally show the health status of connected drives, raid controller, battery etc from within the vSphere Client. This driver also allows connectivity from the LSI MSM utility from a windows workstation. The problem is as soon as I connect my intel 520 SSD drives the health status in the vsphere client disappears, also we lose connectivity via the LSI MSM utlity. Any other drives we test are fine, 1TB SAS drives, other SSD drives etc are all OK. The Intel drives are on the compatability list and are supported by LSI but dont work with the VMware driver. If I install a windows OS on the physical server we have no problems. I have logged a ticket with LSI but they havent been very helpful. I am trying to find other people that may have had the same issue and maybe even a fix

    Read the article

  • Jquery html grab + calling a controller action using javascript (ruby on rails)

    - by Zind
    Preface: I consider myself "slightly effective" in ruby on rails, and a complete novice in javascript. Also, yes, I have installed jQuery and associated plugins instead of the default Prototype library. I am in a situation where I am pulling in a table from off-site in an iframe (which is taking care of all internal JS for me) such that when a part of the table is clicked, a td will gain the class "active." What I would like to do is take this info (I'm assuming I can get it in a string format), and pass it to a method (in my controller, I'm assuming) which will parse the html, pull out the pertinent info, and then call a creation method in the same controller with the parsed info, the end result being a new item in that table. What I have so far is javascript which I believe is correct so far: <script type="text/javascript"> var ImportInfo = function() { var info = $('td.active').html(); // call controller action which parses the given string, //checks for existence in database, and adds new row if needed } $("#Import").click(ImportInfo); </script> and, of course, a button with id="ImportLocation." I have looked at this question: http://stackoverflow.com/questions/1334447/using-jquery-to-call-a-controller-action but am somewhat unsure as to how to call a controller action to pass the contents of the td as a string. Is this doable with the jQuery post method?

    Read the article

  • Test Ruby-on-Rails controller with RSpec and different route name

    - by jhwist
    I have a Rails model named Xpmodule with a corresponding controller XpmoduleController. class XpmoduleController < ApplicationController def index @xpmodule = Xpmodule.find(params[:module_id]) end def subscribe flash[:notice] = "You are now subscribed to #{params[:subscription][:title]}" redirect_to :action => :index end end The original intent was to name the model Module which for obvious reasons doesn't work. However I still want to have the URLs look like /module/4711/ therefore I added this to my routes.rb: map.connect '/module/:module_id', :controller => 'xpmodule', :action => 'index' map.connect '/module/:module_id/subscribe', :controller => 'xpmodule', :action => 'subscribe' Now I want to test this controller with Rspec: describe XpmoduleController do fixtures :xpmodules context "index" do it "should assign the current xpmodule" do xpm = mock_model(Xpmodule) Xpmodule.should_receive(:find).and_return(xpm) get "index" assigns[:xpmodule].should be_an_instance_of(Xpmodule) end end end for which I get No route matches {:action=>"index", :controller=>"xpmodule"}. Which of course is sort-of right, but I don't want to add this route just for testing purposes. Is there a way to tell Rspec to call a different URL in get?

    Read the article

  • Linux Mint 14 severe overheating

    - by agvares
    I've tried switching to Mint (it was Mint 12) about 6 months ago, but failed to do it due to enormous overheating which made it virtually impossible to run any applications more complex than Gedit. Time had passed, and now I'm back again with Mint 14, but feeling way more determined. What I face are the following issues: 1) Great overheating (and by great I mean that just by doing nothing my CPU temp is floating around 70-75 C, which I find a lot) 2) Running multiple applications (let's say Chrome, Skype and Pidgin) results in critical overheating and immediate shutdown of the system 3) Due to the stuff listed above, my battery drains in about 10-15 minutes, pretty much turning my laptop into a crippled desktop machine I've got a HP-dv6 laptop (i7, 6gb RAM, dual graphics) Here's the output of lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler XT [AMD Radeon HD 6700M Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0d:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01) 19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) what i've tried to do already: 1) I've edited my grub file to add some "splash" arguments there 2) Installed jupiter and powertop 3) Tried to upgrade to newer kernels (up to 3.8), btw running anything newer than 3.5 results in both resolution and wi-fi detection fail 4) Read lots of forum threads devoted to the topic So, my question is simple: What else might I do to become finally able to use Mint as my default OS without the risk of being burned alive by the CPU heat?

    Read the article

  • Laptop wakes from sleep, once, due to audio controller (Windows 7)

    - by stijn
    The laptop is a recent Dell XPS 15z and the problem is as follows (reproducible about 90% of tries): put laptop to sleep using either Start-Sleep or closing the lid laptop goes to sleep after about 5 seconds, but instantly wakes again showing a black screen (touching the keyboard or moving the mouse shows the login screen one normally gets after wake) login again, put laptop to sleep latop stays in sleep mode output of powercfg -lastwake after the first instant wake shows the audio controller is responsible. Why would that be, why only the first try, and how to fix this? Wake History Count - 1 Wake History [0] Wake Source Count - 1 Wake Source [0] Type: Device Instance Path: PCI\VEN_8086&DEV_1C20&SUBSYS_04461028&REV_05\3&11583659&0&D8 Friendly Name: Description: High Definition Audio Controller Manufacturer: Microsoft

    Read the article

< Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >