Search Results

Search found 19279 results on 772 pages for 'everything'.

Page 556/772 | < Previous Page | 552 553 554 555 556 557 558 559 560 561 562 563  | Next Page >

• SATA disks boot order?

  - by kire

  I have a computer with 4 SATA disks connected, 2 to the motherboard and 2 to a PCI-card. I've moved all the disks from other computers so 2 of them already has windows installed, the other 2 has just had data on them. I know one of the windows installations works and i want to use this install. If i only have this disk connected the computer boots fine. The problem is that when i boot with all 4 disks connected i get an error message about not being able to boot. This message is in swedish(the wrong windows installation is swedish) so it has to come from that installation. Ok, that means it is trying to boot from wrong disk, i try to pull out that disk but then i get the same error in english. I pull out the fourth disk instead I get another error about NTLDR not being able to load. If i disconnect all drives except the one with the correct windows installation, windows boots fine and i can also connect the other drives while windows is running and browse around in them without any problems. I have no clue what to do. In my BIOS setup i can only select SATA as boot-option, not the order of the disks. I also tried to remove what's left of windows on the other disk by simply deleting everything in explorer(got hidden- and sytstem-files visible). Both windows installations are XP btw. Edit: I switched the cables around and now it magically works. :)

  Read the article

• Some Portions of Computer Running Slow (Specifically Graphics)

  - by Mike Gates

  I noticed that a few things are running slow today on my Windows 7 laptop. Specifically, they are: Opening and closing windows takes several seconds for the animation to complete. Windows media player opens fine, but the movies are very laggy MMORPG's, such as RuneScape, are extremely laggy When waking my computer from sleep mode, after entering my password, my desktop takes about 3 seconds to fade in Other than those, everything runs at a normal speed. Things I've done that maybe contributed to this problem: Changed the graphics processor (by plugging in/unplugging the charger) [however, no matter how I change the graphics, I'm still getting this lagginess] Installed AdBlock, a Firefox addon [I recently removed it, and I'm still experiencing this problem] Went into Advanced System Settings, Clicked Settings, and unchecked a few visual things (such as the animation for opening and closing windows) [sure, this got rid of the opening/closing windows lag, but I like that little animation - plus that leaves all the other lag problems I'm experiencing] So, does anyone have any ideas/fixes? If so, please respond. Thank you. Some Other Information: I'm on a HP Pavillion dv7 laptop, 4285 Entertainment PC, with: intel CORE i5 inside, ATI Mobility Radeon Premium Graphics, Microsoft DirectX11 Opening and closing of windows: Defined as opening a program (i.e. Firefox) or closing it by hitting the X in the upper-right hand corner. Lately, the animation for opening and closing windows (which is simply either growing from the icon from the taskbar to fill the screen, or shrinking from the screen down towards the icon on the toolbar.) This problem also occurs for minimizing/maximizing windows. Very laggy movies: defined as .avi movie files saved to My Documents which skips several frames per second and seemingly slows down the movie as a whole Extremely laggy games: I tried RuneScape today, and movement in the game was at least 10x slower than it ever has been, even when playing on the lowest detail/graphics Desktop taking 3 seconds to fade in after sleep: in this scenario, I had no other programs running visibly. The computer generally fades to black from the password screen to the desktop in about 1 second, normally. However, it is now taking 3 or more seconds.

  Read the article

• computer randomly restarting. both in game and out of game

  - by eric

  first my specs are. AMD Phenom II x4 955 processor 3.2ghz 20gb ddr3 ram 4Gb Nvidia Geforce GTX 770 850w Corsair tx850w psu Gigabyte ud3 mobo Windows 7 professional I recently uprgraded my vid card to gtx770 and upgraded my psu to the 850w thats in it now. i did a reformat with the installation of the new gpu and psu and started fresh and only have a couple programs installed (diablo3, nvidia control panel, wow, and steam). all drivers are up to date and everything is hooked up correctly. the problem is it will randomly shut down. no blue screen. just turns itself straight off and reboots after a couple seconds. occasionally i will have to unplug the power cable from the psu for a few minutes then reconnect and it will start up. it seems pretty random. sometimes it does it when my pc is just sitting there on the home screen. and sometimes it does it during games. and sometimes it doesnt do it for days at a time. i noticed the psu felt hot so i put an extra fan blowing straight onto both the psu and gpu and neither feel overly hot after it shuts down now. could it just be that it is a psu problem. the psu was taken from another machine but wasnt having this problem in that machine. i have seen a few articles online about gtx770 doing the same thing. but i havent found any answers or solutions. any help will be appreciated. im sure the 850w is enough to power my machine, im just stumped and ran out of ideas to fix it. i have even returned the video card for another thinking it might have been an issue with that particular card, but still gettin the same problem.

  Read the article

• Did Windows 7 Startup Repair trash My Documents?

  - by Metaphile

  Earlier today, I rebooted my computer. Partway through the boot process, it shut down suddenly. When I tried again, I was prompted to run Startup Repair, and I did. Afterwards, my computer booted normally and everything seemed to be in order. Then I noticed that my My Documents folder contains a mix of old and new files. On closer inspection, it appears that Windows has reverted my system to a previous state. Two things puzzle me: 1) According to Microsoft, "System Restore does not affect personal files, such as e-mail, documents, or photos [...]", yet many of my personal files have been affected. 2) Why were some things reverted, but not others? I had recently reorganized a bunch of files in My Documents. The reverted directory structure seems to be a hybrid of old a new, with a lot of new stuff missing. It's hard to say for sure, but it looks like the stuff that's missing would have been in conflict (two folders with the same name, for example), and Windows favored the old stuff. Is this normal behavior for Startup Repair/System Restore? To modify personal files, I mean? Is there a pattern to the mess it's made of My Documents?

  Read the article

• Virtual machine shows no network adapter

  - by Logman

  I had a an old Lotus/Domino server (R5), I just virtualized. It ran Windows 2000 server. I had to use Vmware Converter v3.x to create the vm because it was the only one I could find that could actually do a Win2k machine that had no service packs. It was just put out to pasture a couple months ago, so it isn't being used except to store the old email for archiving. It took a bit of work to get it onto the Win2008R2 servers hyper-v but I got it there. Problem now, is that the network adapter didn't show up. I could not install the guest additions because it needed sp4 + on win2k... so I installed sp4 onto the vm guest. Everything seems fine except the network adapter still isn;t showing up in device manager. NOthing. Now this server had an external ip, and I did not want it to be put onto the internal virtual network. I am going to use a dedicated adapter on the host (hyper-v server) if that matters... but this shouldn't matter if the the guests network adapter doesn't show at all. Thoughts?

  Read the article

• how can a web page change my mouse speed?

  - by Tekaholic

  I usually have many tabs open in Firefox and I haven't been able to find one specific website that causes this because I don't seem to notice it right away. I'm going to click on something on my desktop and I am lifting up the mouse several times to get across the screen. It doesn't seem to matter what program I might be using because this happens on all desktops and in Firefox, too. So I go in my settings and I turn up the mouse speed all the way and it's still not really acceptable. It doesn't matter if I click on different tabs but when I close the browser, my mouse is way too sensitive, like I'd expect at the max setting. Then I go back to Control Center and return my mouse speed and acceleration to normal. When I restart my browser, the mouse remains normal. So is there something to this before I start wasting my time hunting through my history to discover which website or sites are having this effect? ...and if it is a specific site and I locate it, what can I change to stop it's effect on my mouse besides not visiting it? I am using Linux Mint 13 on a box with an AMD Athlon processor and 2gigs of ram. I never installed another browser because everything works for me.

  Read the article

• Computer makes odd noise. Replace almost every component. Computer still makes odd noise.

  - by ShimmerGeek

  My PC was getting pretty old, 5 years or so, and over the course of it's life I replaced the graphics card, HDD and a couple of sticks of RAM; but the PSU, processor, motherboard, fans etc. were all original. A few weeks ago, I started hearing an odd noise. I struggle to describe it, it sounded sortof like the 'click of death' you hear when a HDD may fail, but not quite... (And it was far less irregular) Also, I was sure I heard it once or twice a minute or two after I shut down the PC. This was going on very irregularly for a couple weeks. Some days I would hear no noise at all, others I would hear it often, maybe once every 30 seconds or so. I could find no common denominator - i.e. it did not happen more during gaming or any other intensive use. Anyway, I need my PC to sit some classes over the summer, so I put it in for them to run a HDD stress test and to replace a bunch of the components. I ended up replacing almost everything - the only elements I still have are my blu-ray drive and graphics card. They said when they started to run the HDD stress test it failed instantly (They started the test and it immediately said 'Test Complete' so they assumed it was at fault, and put a new HDD in since I was still under warranty with them.) I took it home a few hours ago, and I am still hearing the noise!!! Do you guys have any theories? I'm getting a little worried, I can't afford for my PC to suddenly fail during the next month - I have a lot of coursework to do. Any thoughts? Is it possible it could be the fan on the graphics card? I'm confused because it's so irregular. Any help would be much appreciated.

  Read the article

• windows server 2003 speed issues

  - by farzinSH

  I have a HP server with windows server 2003 and 50 windows XP clients. Since a week and a half the networks speed suddenly drop 2-3 times per day. It gets so slow that none of the clients could work with the HIS program installed on them. We tried so many different things such as replacing the hubs,switches and even some wires. Every time one of these changes solves the problem and the network goes back to its normal state. I checked everything. Even when I disconnected all the clients from the server and connected it to just one computer the problem still remained for 2 hours. I just narrowed down the problem to the couple of likely speculations as follows: viruses? (Updated Kaspersky running on the server shows none) server hardware failure? Physical memory usage on the server? (Because the last time the problem occurred none of the changes above solved the issue so I restarted the server an checked the physical memory usage which was 2 GBs. But I noticed it's increasing over time to over 9 GBs...the server has 16 GBs of RAM.) I surfed the internet and got nothing. Any help would do us a lot....thanks in advance

  Read the article

• What would prevent the same ActiveX control from downloading on one internal website but not another?

  - by ProfessionalAmateur

  We have two internal webservers for an application at my company, one is the development server and the other is production. This application server will deploy and install and ActiveX control to allow the use of specific functionality. The ActiveX control is the exact same on both servers. Last week suddenly when trying to install and run this ActiveX control from the development server stopped working. IE will still prompt the user to install it, but when select "Install this Add-on for all users on this computer", nothing happens. Another IE window pops open and immediately closes and that is it. It is almost as if a pop-up blocker is running (but it is not enabled). The kicker which has me completely stumped is that if we try the same thing on the Production server, everything works as we would expect. Items of interest: Both servers are in the 'Trusted Sites' No pop-up blocker in IE is activated ActiveX controls for Trusted and Intranet Sites are all enabled. Has anyone experienced something similar? I'm not a Windows administrator so please feel free to explain things as elementary as you see fit.

  Read the article

• How to securely control access to a backend key server?

  - by andy

  I need to securely encrypt data in my database so that if the database is dumped, hackers are unable to decrypt the data. I'm planning on creating a simple key server on a different machine, and allowing the DB server access to it (restricted by IP address on the key server to permit the DB server). The key server would contain the key required to encrypt/decrypt data. However, if a hacker were able to get a shell on the DB server, they could request the key from the key server and therefore decrypt the data in the database. How could I prevent this (assuming all firewalls are in place, DB is not connected directly to the internet, etc)? i.e. is there some method I could use that could secure a request from the DB server to the key server so that even if a hacker had a shell on the DB server they'd be unable to make those same requests? Signed requests from the DB server could make issuing these requests less trivial - I suppose that'd help increase the amount of time it'd take to compromise the key server, something a hacker probably wouldn't have much of. As far as I can see, if someone can get a shell on the DB server everything's lost anyway. This could be mitigated by using one key per data item in the DB so at least there's not a single "master" key, but multiple keys that the hacker would need to access. What would be a secure method of ensuring requests from the DB server to the key server were authentic and could be trusted?

  Read the article

• mdadm lvm and ext4 slowness - How can I speed it up?

  - by beatbreaker

  I can't figure out why I'm getting such terrible times out of my mdadm and in particular the lvm partitions in it. I made the raid: mdadm --create --verbose /dev/md0 --level=5 --chunk=1024 --raid-devices=4 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 # cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md0 : active raid5 sda1[0] sdd1[3] sdc1[2] sdb1[1] 2930279424 blocks level 5, 1024k chunk, algorithm 2 [4/4] [UUUU] I then created the physical volume, volume group, and logical volumes, I then formatted the logical volumes to ext4 using the following commands I got from here: http://busybox.net/~aldot/mkfs_stride.html mkfs.ext3 -b 4096 -E stride=256,stripe-width=768 /dev/datavg/blah Now I'm confused, I had these lvs running real quick before in mdadm but now that I've 'optimized' everything it's slower, eg, before: /dev/datavg/lv_audio: Timing buffered disk reads: 598 MB in 3.01 seconds = 198.85 MB/sec but now after: /dev/datavg/audio: Timing buffered disk reads: 198 MB in 3.00 seconds = 65.96 MB/sec That's pitiful! What's happened here? Did I not follow the instructions correctly? Can i reshape the ext4 partitons to default back to what they were? (I used defaults before and they were fine!)

  Read the article

• How many bootable partitions are possible to have on one hard drive?

  - by draiden

  This may not be the correct place to post this; if that's the case, just let me know and point me in the right direction please! I'm thinking of building a box that needs to be lightweight and portable, and would need to be able to boot multiple installations of windows. I am needing to have multiple installations so that I can, for example, plug the box in to the network at one location, boot in to that location's partition, and have full access to everything I would normally need to do on a computer that has already been set up on that network. Then, when I go to the next client, I would be able to do the same thing, with the new location's partition, and have all of those network settings, drive mappings, etc., available there. Obviously I'd need to go through and set them all up on the different locations/networks, I'm not expecting it to magically know where I am and what I'm doing. It would be like I'm carrying around a computer that is configured for each place I need to go in one little box, instead of having to have multiple computers or having to reconfigure all the settings and such every time I go to another client. Or is there an easier way to do this that I haven't learned of?

  Read the article

• My Ubuntu 10.04 server kills all WAN bandwidth when it's attached to my LAN. Where do you begin troubleshooting?

  - by rrc7cz

  First I should say that my Linux knowledge is minimal; just enough to set up some servers (Apache, Tomcat, Couch, etc). I built a MiniITX server to host some simple sites, act as an SSH tunnel while I'm away, and act as a torrent server. It was not properly secured for a long time (iptables was empty, all ports open, no firewall) though my router did not have much port forwarding set up beyond HTTP, FTP, and SSH. A week or two ago my bandwidth at home dropped from around 27Mbps to 2Mbps and my upload went from 7Mbps to 0.06Mbps. When I unplug the server from the LAN, by bandwidth shoots back up. I threw up a restrictive iptables, removed most of the port forwarding, and checked my router logs to see if there were any open connections from the server (malware?) but there were none. What would you do? What are the first things you'd check? I can of course reinstall everything from scratch, but I'd like to find the root cause.

  Read the article

• How to setup IIS 7.5 Reverse Proxy for quite a few internal servers - Server Farm?

  - by Tim Murphree

  I have tried for a few days, but I'm lost. Here's what I'm trying to do: I want to setup an IIS 7.5 as a Reverse Proxy for about 30 internal HTTP servers, located on my internal LAN. Everything is running on port 80. The internal servers are really IP based webcams. Here is scenario: www.mycamserver.com/cam1 192.168.1.101 www.mycamserver.com/cam2 192.168.1.102 and so on, until.. www.mycamserver.com/cam30 192.168.1.130 I have installed ARR and URL Rewrite. So far, I have managed, at one time, to seem to forward an incoming URL to an internal server, but the page would not fully load (error 404). Also, I setup a Server Farm, but it seems all traffic is now set to the first node on the Server Farm (192.168.1.101). However, at least the page loads and runs correctly. I simply want to do an exact match, for example, "cam14", and reverse-proxy / rewrite to a corresponding internal server address - "192.168.1.114".

  Read the article

• Using iptables to make a VPN router

  - by lost_in_the_sauce

  I am attempting to make a VPN connection to a third party VPN site, then forward traffic from my internal computers (ssh and ping for now) out to the VPN site using IPTables. 3rd Party <- (tun0/eth0)Linux VPN Box(eth1) <- Windows7TestBox I am running on CentOS 6.3 Linux and have two network connections eth0-public eth1-private. I am running vpnc-0.5.3-4 which is currently connecting to my destination. When I connect I am able to ping the destination IPAddresses but that is as far as I can get. ping -I tun0 10.1.33.26 success ping -I eth0 10.1.33.26 fail ping -I eth1 10.1.33.26 fail I have my private network Windows 7 test box set up to have the eth1 (private) network of my VPN Server as its gateway and can ping him fine. I need IPTables to send the Windows 7 traffic out the VPN tunnel. I have tried for a few days many different IPTables configurations from this site and others, either the other examples are too simple or overly complicated. The only thing this server is doing is connecting to the VPN and forwarding all traffic. So we can "flush" everything and start from scratch here. It is a blank slate. #!/bin/bash echo "Define variables" ipt="/sbin/iptables" echo "Zero out all counters" $ipt -Z $ipt -t nat -Z $ipt -t mangle -Z echo "Flush all active rules, delete all chains" $ipt -F $ipt -X $ipt -t nat -F $ipt -t nat -X $ipt -t mangle -F $ipt -t mangle -X $ipt -P INPUT ACCEPT $ipt -P FORWARD ACCEPT $ipt -P OUTPUT ACCEPT $ipt -t nat -A POSTROUTING -o tun0 -j MASQUERADE $ipt -A FORWARD -i eth1 -o eth0 -j ACCEPT $ipt -A FORWARD -i eth0 -o eth1 -j ACCEPT $ipt -A FORWARD -i eth0 -o tun0 -j ACCEPT $ipt -A FORWARD -i tun0 -o eth0 -j ACCEPT Again I have done many variations of the above and many other rules from other posts but haven't been able to move forward. It seems like such a simple task, and yet....

  Read the article

• PPTP VPN on Server 2008 Enterprise

  - by Mike K

  I asked this question on Server fault and was told that was not allowed so im moving it here. I am running Windows Server 2008 enterprise in my HOME network inside of vmware workstation. I am running this on my home network to setup a PPTP VPN connection at home. I have correctly setup everything I needed to make it work, including opening all the ports, 1723 and 43 (GRE). I am able to connect just fine, but when I connect I dont have internet unless I uncheck use remote gateway. The thing is, I want to use the remote gateway to route all my traffic through that connection. Can someone tell me why this isnt working and how to get it to work. When I have remote gateway checked, and I do an ipconfig I dont get a remote gateway for the VPN connection, its 0.0.0.0 when id assume if connected properly should be 192.168.1.254 (my ATT Home Router). Also, if I cant get the remote gateway issue to work, and I have to uncheck that box to get internet, does this mean my VPN session is no longer encrypted? I am fully aware the PPTP VPN is the weakest VPN encryption out there but still having that extra layer of security when im on an unsecure wifi connection makes me feel a bit better. Thank you for all your help in advance. Someone told me I need to setup a gateway or router configured on the server. If thats the case, how go I go about telling the remote co

  Read the article

• How to route 1 VPN through another on OS X?

  - by Eeep

  Hi everyone. Thanks a lot for your help! I've been tinkering with this for a while and have read many posts along with Googling for help, but my knowledge of TCP/IP is really weak... I have access to two different VPN servers. 1 Is set up in Network Settings and connects through PPP 2 Is set up through Tunnelblick and uses OpenVPN. I can connect to either tunnel #1 or tunnel #2, but not both one after the other... One of my major to-do's this year is study TCP/IP, but for now, would you be super-helpful and help me fix this really clearly? I have no experience with routing, DNS, gateways or any of that. If you tell me, "Set your gateway to XXX.XXX.XX.XXX" can you specify how I get that IP, off of what interface so I don't get messed up? I can figure out the terminal just fine if you let me know what to type, and I WILL read the man pages on everything you help me with. Thanks a million!

  Read the article

• How do I fix a permissions problem with MS Distributed File System?

  - by charlesrandall

  I have a computer that is new, Windows 7, that is supposed to have access to particular network resources on a Distributed File System. However, despite all permissions being set correctly, I have consistent trouble accessing them. For instance, I'm supposed to be able to reach \company.org\main\subdir. All the permissions have been granted, only when I try to access it by name, it tells me I don't have permission to access \main. This is where the fun starts. If I ping company.org, get the IP, replace company.org by the IP, I can then access \IP\main\subdir without any problems at all. However we have a ton of scripts and build tools that access the network resource by name. My sysadmin has found that using MS's dfsutil.exe, we can fix it temporary using this sequence of commands: C:\dfsutil.exe /pktinfo C:\dfsutil.exe /PktFlush C:\dfsutil.exe /SpcFlush C:\dfsutil.exe /PurgeMupCache C:\dfsutil.exe /pktinfo After that, everything is great... until I reboot, or until some unspecified time later where suddenly I don't have access to \main\ anymore. Hoping to find a more permanent solution than waiting for it to break and running a batch file.

  Read the article

• Hourly SQL Server 2005 Slowness (Possibly caused by SYSTEM)

  - by Zorlack

  We're trying to diagnose the cause of slowness on our Database server. We're running the latest rev SQL Server 2005 on Windows 2008x64. The behavior that we're seeing is this: We see the SYSTEM process spike one of the CPUs for about 2 minutes, during this time SQL server slows down by a factor of 10. The slowness lasts until SYSTEM is done, then in an hour everything starts again. During these slowdowns disk writes don't spike, paging doesn't spike, the only noticeable precursor we see is that SYSTEM maxes out one of the sixteen (HT)CPUs. Note that this doesn't happen at the top of the hour, it just happens once an hour, and it shifts a bit depending on the length of the incident. At the moment this is causing intermittent slowdowns, but when the server is really busy it can cause Worker Thread starvation. The server is a Dual Quad Dell R710 with 96GB of RAM and RAID10 data/log disks. Has anyone experienced this kind of problem? Does anyone know where we should look? Edit: SQL Server Version is 9.0.4035

  Read the article

• Virtual hosting in lighttpd?

  - by lighttpdnewbie

  Ok, here it goes... I've seen some other posts dealing with this, but it didn't help that much. I am using windows XP. My problem is with trying to get lighttpd working with virtual hosts. Now, I managed to get everything up and working with the default /htdocs and the default page shows up just fine on the internet, but since I have several sites to host, I need virtual hosting. I managed to do it in apache, so I guessed it would work out just fine in lighttpd, but apparently I'm missing something. Ok, let's say I have domain (www.)example.org. I want everyone using that url going to the correct index.html, obviously. Let's say that index.html is in directory "websites/website1" placed under the lighttpd dir. (thus, the full path is c:/ProgramsFiles/lighttpd/websites/website1/index.html) Now: how, exactly, do I set up my virtual host (in the config file)? In detail, please, since I've tried for hours with the vague hints I got from fora and such, but it doesn't work. Also; is there something additional to do? Change the "server.bind" or get rid of the default server.document-root, or something? I appreciate all the help you can give! Especially if it's a verbatim/step-by-step solution you're offering! ;-p Edit: And, yes, my mod_simple_vhost has been enabled.

  Read the article

• How to diagnose computer freezing problem

  - by reinierpost

  I have a laptop (a Medion from Aldi) that tends to hang quite often - so often, in fact, that several attempts to install Windows XP or Ubuntu on it have all failed. However, I am able to boot and run Ubuntu as found on the standard Ubuntu 10.10 installation image. I have done this two times thus far. The first time everything was running smoothly, until at some point the GUI (i.e. X) became unresponsive. The cursor kept moving with the mouse, but menus would no longer show and clicking things no longer produced any response. So I switched to the consoles (Ctrl-F1, Ctrl-F2, etc., which in this setup automatically run shells. The shells were still responsive, and the cd command would still work, but any command that invoked an executable (e.g. /bin/ls or cd /bin; ./find caused the shell to hang up uninterruptibly. My hypothesis was that all attempts at disk access were hanging up, but I didn't actually try a command like echo /proc/$$ or while read line; do echo $line; done < /var/log/syslog to verify this. Another possibility is that an essential system library is cached in memory and somehow failing to function properly. The second time I left the system running overnight and it didn't hang itself spontaneously. I'm not sure I have the patience to just twiddle with the running system until the condition reappears, and I'm, not sure what to do once it does. Clearly we can rule out a software cause. It seems disk access related, but clearly it's not permanent hard disk failure because the system will reboot just fine. What kind of hardware problem might produce these symptoms? Can it be a memory problem?

  Read the article

• Can't reach only certain websites from my Wifi (with macbook and iphone)

  - by trampj

  I can't access certain websites neither from my macbook nor from my iphone when connected to my Wifi. The same website can be opened from another windows computer connected to the same Wifi. This is what happens when I try to ping it: PING ilpost.it (151.1.175.113): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 ... And when I try to traceroute it: host-001:~ j$ traceroute www.ilpost.it traceroute to ilpost.it (151.1.175.113), 64 hops max, 52 byte packets 1 vodafonedslrouter (192.168.1.1) 2.965 ms 0.743 ms 0.745 ms 2 * 2.96.54.77.rev.vodafone.pt (77.54.96.2) 12.076 ms 10.871 ms 3 77.41.30.213.rev.vodafone.pt (213.30.41.77) 14.145 ms 10.693 ms 11.960 ms 4 85.205.11.49 (85.205.11.49) 9.658 ms 8.946 ms 9.085 ms 5 85.205.13.105 (85.205.13.105) 57.497 ms 57.621 ms 48.080 ms 6 188.111.129.17 (188.111.129.17) 49.483 ms 51.338 ms 48.852 ms 7 85.205.25.174 (85.205.25.174) 47.891 ms 49.219 ms 47.821 ms 8 * * * 9 * * * 10 * * * 11 * * * I've flushed my DNS cache but nothing changed. This is quite dramatic as it seems to depend on 85.205.25.174 hop and don't know how to avoid it. Any suggestions? I add that 3 days ago everything worked fine. Then it has stopped.

  Read the article

• Can't reach only certain websites from my Wifi (with macbook and iphone)

  - by mellin

  I can't access certain websites neither from my macbook nor from my iphone when connected to my Wifi. The same website can be opened from another windows computer connected to the same Wifi. This is what happens when I try to ping it: PING ilpost.it (151.1.175.113): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 ... And when I try to traceroute it: host-001:~ j$ traceroute www.ilpost.it traceroute to ilpost.it (151.1.175.113), 64 hops max, 52 byte packets 1 vodafonedslrouter (192.168.1.1) 2.965 ms 0.743 ms 0.745 ms 2 * 2.96.54.77.rev.vodafone.pt (77.54.96.2) 12.076 ms 10.871 ms 3 77.41.30.213.rev.vodafone.pt (213.30.41.77) 14.145 ms 10.693 ms 11.960 ms 4 85.205.11.49 (85.205.11.49) 9.658 ms 8.946 ms 9.085 ms 5 85.205.13.105 (85.205.13.105) 57.497 ms 57.621 ms 48.080 ms 6 188.111.129.17 (188.111.129.17) 49.483 ms 51.338 ms 48.852 ms 7 85.205.25.174 (85.205.25.174) 47.891 ms 49.219 ms 47.821 ms 8 * * * 9 * * * 10 * * * 11 * * * I've flushed my DNS cache but nothing changed. This is quite dramatic as it seems to depend on 85.205.25.174 hop and don't know how to avoid it. Any suggestions? I add that 3 days ago everything worked fine. Then it has stopped.

  Read the article

• What could possibly cause my computer to power down at random times?

  - by geoffreydv

  I have recently bought a new Power Supply and a new graphics card. My PC ran smoothly for a few months now but since a couple of days I'm having a strange problem. I am trying to isolate the problem to a specific piece of hardware (because if it's either the Power Supply or the Graphics card they are still under warranty). The problem started when I was playing a game (diablo 3). My PC suddenly powered down. I was unable to turn it on again by pressing the power button. I unplugged the power cable for a few seconds and plugged it back in. This time the pc powered on but the indication light turned orange instead of white as it normally does. The fans were not spinning and I did not see anything on my screen. After trying a couple of times I gave up. Two days later I tried again and this time the PC did boot up as usual. Everything looked okay until I tested if the problem was resolved by starting Diablo again. After about two minutes it powered down again as it did the first time. If I don't run any games my PC does power down after about 3-5 hours. Another fact that might be relevant: One time the PC did not shut down immediatly, instead first my graphics "powered down" but the music I was playing kept on playing. After about 20 seconds the pc powered down completely as usual. What I also noticed is that when I boot instantly after a power down, the chance of another power down occuring is much higher. Does anyone have an idea what could be causing this kind of behaviour or has a certain tool to diagnose the specific hardware parts? Thanks Specs: Memory: 6GB Processor: Intel i5 OS: Windows 7 64 bit The PC is a Dell Studio XPS 8100 with a replaced PSU and Graphics card: PSU: Corsair CX500 (500 watt) Graphics card: AMD Radeon 6850

  Read the article

• WebSphere hung threads, how can I track then down?

  - by Puzzled

  We have an application running on WebSphere (unfortunately it is 6.1 which is no longer supported, it has not yet been migrated in production to a later version) which becomes entirely unresponsive because of hung threads. As far as I can tell we entirely exhaust one of the thread pools. I have activated hung thread detection and I get a core/thread dump when hung threads are detected. The server can run for several days without problems but has crashed twice this week. When load the core/thread dump in "IBM Thread and Monitor Dump Analyzer for Java", it tells me that there are a certain number of hung threads (this time it was 2, last time 11) and multiple (usually around 40) threads "waiting on condition" and some running threads. I believe one of the thread pool has around that size (50). Now what I see in there are threads waiting for locks, having locks or in wait. Most of them show a stack track which always ends like this: at java/lang/Object.wait(Native Method) at java/lang/Object.wait(Object.java:231) Now, how can I track this down to either a server configuration problem, application issue, WebSphere problem or something else? How is this supposed to help me track down the problem when almost everything in there refers to IBM code? I cannot ask IBM's help as 6.1 is now an unsupported version of WebSphere and while work has been done to make it work under WebSphere 7 we are not yet ready to switch to it in Production yet.

  Read the article

< Previous Page | 552 553 554 555 556 557 558 559 560 561 562 563  | Next Page >