Search Results

Search found 18191 results on 728 pages for 'single board'.

Page 556/728 | < Previous Page | 552 553 554 555 556 557 558 559 560 561 562 563  | Next Page >

• Faster, secure, protocol/code required for long-distance transfer.

  - by Chopper3

  I've ran into a problem and I'm looking for a new secure protocol/client/server that's faster over a 1Gb/s fibre link - let me tell you the story... I have a pair of redundant, diversely-routed, 1Gb/s links over a distance of around 250 miles or so (not dark fibre but a dedicated point to point link, not a mesh). At the 'client' end I have a HP DL380 G5 (2 x dual-core 2.66Ghz Xeon's, 4GB, Windows 2003EE 32-bit), at the 'server' end I have a HP BL460c G6 (2 x quad-core 2.53Ghz Xeons, 48GB, Oracle Linux 5.3 64-bit). I need to transfer around 500 x 2GB files per week from the client to the server machines per week - but the transfer NEEDS to be secure. Using both iPerf or regular FTP I can get ~80MB/s of transfer pretty consistently, which is great. Using WinSCP or Windows SFTP I can't seem to get more that ~3-4MB/s, at this point the server's CPU is 3% busy while CPU0 of the client goes to ~30% utilised. We've tried editing various TCP window sizes with little success. Both ends are connected to quite low-usage Cisco Cat6509's with Sup720's. I can replace the client machine with a newer machine and/or move it to Linux - but this will take time. Clearly these single-threaded secure Windows clients are introducing too much latency doing their encryption. So a few questions/thoughts; Are there any higher performing secure protocols or client software for Windows that I could try? I'm pretty protocol-gnostic so long as it'll work between Windows and Linux. Should I be using hardware to do the encryption, either in the client or the network parts? If so what would you recommend? I'm not convinced that just swapping the server would be that much faster, the CPU was only at 30% but then again that's higher than I'd have expected given the load - moving to Linux at the client end may be a better idea but would be quite disruptive. Am I missing a trick? Thanks in advance.

  Read the article

• umask seems to vary by user

  - by paullb

  I've got a development Ubuntu system for which I have several users: myself (with full sudo) and about 5 other users. (I've set up the system so everything in this respect is still at its default setting) I'm trying to set the system up so that multiple people can collaborate in a single directory by using grouing and I want the default permissions to be 664. However when some users edit files the permissions were 644. After a lot of investigating most users have a umask (checked at the prompt) of 0002 and when they create files they are 664 (as expected) but there are 2 (myself and one other) who have 0022 umask (so the files that come out are 644 and nobody else can write to them). I've looked everywhere but can't figure out why a couple users wind up with a different umask e.g. there is nothing the .bash_profile or anything like that) Any ideas for the source of the discrepancy? /etc/bashrc if [ $UID -gt 199 ] && [ "`id -gn`" = "`id -un`" ]; then umask 002 else umask 022 fi /etc/profile if [ $UID -gt 199 ] && [ "`id -gn`" = "`id -un`" ]; then umask 002 else umask 022 fi EDIT: My (bad) ~/.bashrc # .bashrc # Source global definitions if [ -f /etc/bashrc ]; then . /etc/bashrc fi # User specific aliases and functions export LANG=en_US.utf8 Other user (good) .bashrc # .bashrc # Source global definitions if [ -f /etc/bashrc ]; then . /etc/bashrc fi # User specific aliases and functions

  Read the article

• Setting umask for all users

  - by Yarin

  I'm trying to set the default umask to 002 for all users including root on my CentOS box. According to this and other answers, this can be achieved by editing /etc/profile. However the comments at the top of that file say: It's NOT a good idea to change this file unless you know what you are doing. It's much better to create a custom.sh shell script in /etc/profile.d/ to make custom changes to your environment, as this will prevent the need for merging in future updates. So I went ahead and created the following file: /etc/profile.d/myapp.sh with the single line: umask 002 Now, when I create a file logged in as root, the file is born with 664 permissions, the way I had hoped. But files created by my Apache wsgi application, or files created with sudo, still default to 644 permissions... $ touch newfile (as root): Result = 664 (Works) $ sudo touch newfile: Result = 644 (Doesn't work) Files created by Apache wsgi app: Result = 644 (Doesn't work) Files created by Python's RotatingFileHandler: Result = 644 (Doesn't work) Why is this happening, and how can I ensure 664 file permissions system wide, no matter what creates the file? UPDATE: I ended up finding a cleaner solution to this on a per-directory basis using ACLs, which I describe here.

  Read the article

• FreeNAS pool configuration - RAID1 + other drives

  - by trnelson

  Simple questions, really. I found this answer with a similar setup, but not sure it answers my question. If it does, I'm curious why since the answer seems a bit unsure: ZFS Hard Drive Configuration in FreeNAS I'm building a server which will be used primarily for backup, plus some media streaming, possibly with Plex. I seem to understand most everything I need, but I'm still a bit confused on how pools work, and how to configure them for my scenario. I will have 2x 2TB WD Red drives, which I plan on using in a mirrored set up (RAID1). This would be for backup, and I'd also like to do offsite backup to my CrashPlan account from this array. I also have a few other drives: 1.5TB, 320GB, 250GB. I'm not sure exactly what to do with them yet, but looking for options. FreeNAS OS will be running from a 16GB USB Flash drive. Would it be wise to use the 1.5TB as a backup-backup, essentially as a mirror or perhaps for snapshots of the 2TB RAID1? I'm still learning about snapshots. Should the 2TB mirrored drives be in their own pool? Should the other drives be set up in their own pools as well, or should they be JBOD in a single pool? They may or may not get much use since the 2TB array is plenty for me. Does a dataset basically mimic the idea of a partition or a network share? In other words, I would map \SERVER\Share to X: on my laptop? Let's say I wanted to use the 250GB drive as an encrypted drive to store all of my cat pictures. Would it have to be in its own pool? If I use jails apps, should they go in the backup RAID1, or in another place? Thank you!

  Read the article

• The best way to hide data Encryption,Connection,Hardware

  - by Tico Raaphorst

  So to say, if i have a VPS which i own now, and i wanted to make the most secure and stable system that i can make. How would i do that? Just to try: I installed debian 7 with LVM Encryption via installation: You get the 2 partitions a /boot and a encrypted partition. When booting you will be prompted to fill in the password to unlock the encryption of the encrypted partition, Which then will have more partitions like /home /usr and swapspace which will automatically mount. Now, i do need to fill in the password over a VNC-SSL connection via the control panel website of the VPS hoster, so they can see my disk encryption password if they wanted to, they have the option if they wanted to look at what i have as data right? Data encryption on VPS , Is it possible to have a 100% secure virtual private server? So lets say i have my server and it is sitting well locked next to me, with the following examples covered bios (you have to replace bios) raid (you have to unlock raid-config) disk (you have to unlock disk encryption) filelike-zip-tar (files are stored in encrypted archives) which are in some other crypted file mounted as partition (archives mounted as partitions) all on the same system So it will be slow but it would be extremely difficult to crack the encryption. So to say if you stole the server. Then i only need to make the connection like ssh safer with single use passwords, block all incoming and outgoing connections but give one "exception" for myself. And maybe one for if i somehow lose my identity for the "exeption" What other overkill but realistic security options are available, i have heard about SElinux?

  Read the article

• Anyone have real world experience with Rackspace Cloud Sites at high scale?

  - by Allara

  I have a pure web service application layer using .NET. I was originally planning to use Amazon EC2, but rolling my own autoscaling procedures is a bit intimidating, and the scaling isn't very granular from a cost perspective. If the app is successful, we could be looking at relatively high scale (millions of requests per month). The app uses Amazon SimpleDB as the database layer. As a test, I have the app running successfully in Rackspace Cloud Sites. Performance seems to be equal to (if not better than) a standard EC2 instance, even with the added latency of the SimpleDB requests travelling to the Rackspace network. However, testing at this stage is at a very low scale. My question is this: has anyone had real-world experience running a high scale application on Rackspace Cloud Sites? Moreover, once you pass the "included" 10,000 compute cycles per month, does the overall cost seem to be lower than rolling lots of EC2 instances? My assumption would be that with completely smooth scaling (i.e. only adding compute resources as needed), the cost could be lower on average. However, their stated goal of calibrating 10,000 CCs as a single 1.2 Ghz CPU seems on average to be much more expensive than EC2. I like the idea of no-touch scaling, but is it too good to be true?

  Read the article

• optimal folder structure for storing 100k files on a USB drive

  - by cherouvim

  I need to store 100k files (around 40GB) in a USB drive. Each file has a unique int id (e.g 45000). Option one is to put all files in a single folder: root/ root/1.pdf root/2.pdf root/3.pdf ... root/567.pdf root/568.pdf root/569.pdf ... root/10001.pdf root/10002.pdf root/10003.pdf ... root/99998.pdf root/99999.pdf root/100000.pdf Option two is to create a [1-9][0-9]* folder hierarchy based on that id: root/ root/1/file.pdf root/2/file.pdf root/3/file.pdf ... root/5/6/7/file.pdf root/5/6/8/file.pdf root/5/6/9/file.pdf ... root/1/0/0/0/1/file.pdf root/1/0/0/0/2/file.pdf root/1/0/0/0/3/file.pdf ... root/9/9/9/9/8/file.pdf root/9/9/9/9/9/file.pdf root/1/0/0/0/0/0/file.pdf Which option will scale better? I can understand that the second option will require tons of folders but each folder will at most contain 10 folders and 1 file. Maintenance will not be an issue since everything will be controlled by an application. Note that this is a USB drive on linux and based on the above I'd also like to know whether I should go with FAT32 or NTFS.

  Read the article

• PuTTY inserts random characters during a session

  - by Zachary Polikarpus

  I recently started renting space on a remote server so that I could work on a project. I found that a relatively painless way to access it on a windows machine is through PuTTY. However, there is one thing that has always irked me when using it: for seemingly no reason random characters are sometimes inserted at the cursor. Most of the time it is just a single tilde, but rarely it spits out what looks like some escape sequence ([[^8 or the like). It will only occur when I am focused on the window, whether I am typing or 20 feet away from the keyboard. If left for long enough, it will spit tildes at random intervals (average is about 1 minute). Finally, this behavior seems to be inconsistant when running programs such as nano or the mysql interface: in nano, instead of inserting tildes, it will set marks (ctrl-^); in mysql, lines will become un-editable. My question is this: Has anyone else experienced this sort of behavior in PuTTY? And if so, what can be done to prevent/correct this behavior?

  Read the article

• Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

  - by Biohazard

  I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

  Read the article

• What is a suitable simple, open web server for Windows?

  - by alficles

  I'm looking for a dead simple web server for Windows. Load will not be high as it will be primarily serving binaries for a WPKG update service. It needs to serve the entire contents of a single folder over HTTP on a configurable (high) port. No CGI or other scripting is required, but it might be nice for future features. I started with Mongoose, since it doesn't even have an installation requirement (a very nice perk), but it fails to start when run as a service. (Technically, it acts as it's own installer.) I've investigated LighTPD as well, but it appears to be minimally (at best) tested on Windows. And naturally, I'm looking for something free. As in beer is good, but speech is better, as always. Edit: I didn't mention this initially, but non-tech people will be doing the install. They'll have whatever script I write for the install, but the goal is a simple system that is easy to troubleshoot. (I almost worded this question "What is the best...", but Serverfault rightly observed that that is a subjective question. And it's really not an optimization problem, any suitable solution will work. I just can't seem to find one for Windows.)

  Read the article

• How to configure default text selection behavior in Windows XP, 7? (eg. mouse click selects entire word vs. mouse click inserts an active cursor)

  - by Mouse of Fury

  I find the mouse click behavior of Windows XP and Windows 7 annoying and intrusive. I don't remember Windows NT being quite this bad, or MacOS 7 - 10 which I used in the nineties. When I'm using a browser and I click on a text field - for example, the address bar, or a search box - the first thing which happens is the entire field is selected.Subsequent clicks seem to select parts of words, often deciding arbitrarily to exclude or include adjacent punctuation. The same in Excel and other apps, and when trying to rename files, so I'm assuming this behavior comes from a system-wide text handling routine. I frequently want to edit text, cut out or replace odd parts of the insides of words or chunks of sentences, and often find that to get a simple cursor to insert I have to click the mouse up to 4 times in succession. I've had to do a lot of this recently and it has been driving me insane. Is there a place at the system level where this can be configured? In a perfect world, I'd like a single click on a new text area to insert a cursor point, and a rapid double click to select the entire area. Words or text within the area could be selected by inserting a cursor, holding down the mouse button and dragging to the exact point where I want the selection to end - even if that's in the middle of a word. No, I don't need or want Windows to "smart select" a word or sentence for me. I've looked in the Mouse and Accessibility Options control panels (Windows XP). Haven't found anything even close. Thanks -

  Read the article

• SSH does not allow the use of a key with group readable permissions

  - by scjr

  I have a development git server that deploys to a live server when the live branch is pushed to. Every user has their own login and therefore the post-receive hook which does the live deployment is run under their own user. Because I don't want to have to maintain the users public keys as authorized keys on the remote live server I have made up a set of keys that 'belong's to the git system to add to remote live servers (In the post-receive hook I am using $GIT_SSH to set the private key with the -i option). My problem is that because of all the users might want to deploy to live, the git system's private key has to be at least group readable and SSH really doesn't like this. Here's a sample of the error: XXXX@XXXX /srv/git/identity % ssh -i id_rsa XXXXX@XXXXX @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: UNPROTECTED PRIVATE KEY FILE! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ Permissions 0640 for 'id_rsa' are too open. It is required that your private key files are NOT accessible by others. This private key will be ignored. bad permissions: ignore key: id_rsa I've looked around expecting to find something in the way of forcing ssh to just go through with the connection but I've found nothing but people blindly saying that you just shouldn't allow access to anything but a single user.

  Read the article

• Gigabit network limited to 25MB/s by CPU. How to make it faster?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? The other computers in the network can usually transfer at 50+MB/s without problems. And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• what means parameter -mailboxcredenctial

  - by cotablise

  H3llo, I am writing regarding the Exchange powershell commands. When I want to use following cmdlets, I have to insert parameter -mailboxcredential Test-OwaConnectivity Test-OutlookWebServices Test-ImapConnectivity Test-PopConnectivity In the Microsoft official site is written: "The MailboxCredential parameter specifies the mailbox credential for a single URL test." I am not sure why this parameter is needed... I inserted incorrect credentials, however the command was finished successfully... Could you tell me reason why this parameter is needed ? Example: Wrong/incorrect credential [PS] C:\>Test-WebServicesConnectivity -ClientAccessServer EXhub1 -MailboxCredential (Get-Credential blablabla) CasServer LocalSite Scenario Result Latency(MS) Error --------- --------- -------- ------ ----------- ----- EXhub1 Default-Fi... GetFolder Failure [System.Net.WebExcept... Without parameter: [PS] C:\>Test-WebServicesConnectivity -ClientAccessServer EXhub1 WARNING: Test user 'extest_91ef41d34eef4' isn't accessible, so this cmdlet won't be able to test Client Access server connectivity. Could not find or sign in with user ********\extest_91ef41d34eef4. If this task is being run without credentials, sign in as a Domain Administrator, and then run Scripts\new-TestCasConnectivityUser.ps1 to verify that the user exists on Mailbox server EXHUB1.****** + CategoryInfo : ObjectNotFound: (:) [Test-WebServicesConnectivity], CasHealthCouldN...edInfoException + FullyQualifiedErrorId : FB9A14B6,Microsoft.Exchange.Monitoring.TestWebServicesConnectivity WARNING: No Client Access servers were tested. Thank you in advance

  Read the article

• Is there a utility to visualise / isolate and watch application calls

  - by MyStream

  Note: I'm not sure what to search for so guidance on that may be just as valuable as an answer. I'm looking for a way to visually compare activity of two applications (in this case a webserver with php communicating with the system or mysql or network devices, etc) such that I can compare the performance at a glance. I know there are tools to generate data dumps from benchmarks for apache and some available for php for tracing that you can dump and analyse but what I'm looking for is something that can report performance metrics visually from data on calls (what called what, how long did it take, how much memory did it consume, how can that be represented visually in a call stack) and present it graphically as if it were a topology or layered visual with different elements of system calls occupying different layers. A typical visual may consist of (e.g. using swim diagrams as just one analogy): Network (details here relevant to network diagnostics) | ^ back out v | Linux (details here related to firewall/routing diagnostics) ^ back to network | | V ^ back to system Apache (details here related to web request) | | ^ response to V | apache PHP (etc) PHP---------->other accesses to php files/resources----- | ^ v | MySQL (total time) MySQL | ^ V | Each call listed + time + tables hit/record returned My aim would be to be able to 'inspect' a request/range of requests over a period of time to see what constituted the activity at that point in time and trace it from beginning to end as a diagnostic tool. Is there any such work in this direction? I realise it would be intensive on the server, but the intention is to benchmark and analyse processes against each other for both educational and professional reasons and a visual aid is a great eye-opener compared to raw statistics or dozens of discrete activity vs time graphs. It's hard to show the full cycle. Any pointers welcome. Thanks! FROM COMMENTS: > XHProf in conjunction with other programs such as Perconna toolkit > (percona.com/doc/percona-toolkit/2.0/pt-pmp.html) for mySQL run apache > with httpd -X & (Single threaded debug mode and background) then > attach with strace -> kcache grind

  Read the article

• Why are my Windows 7 updates continuously failing?

  - by Chris C.

  I'm an advanced level user here with an odd issue. I have two Windows Updates that are failing to install, every single time. I'm getting a mysterious "Code 1" error on both updates, an error for which I'm having difficulty finding a solution. The updates in question are: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Because these updates are failing, the Shut Down button in my start menu always has the shield icon next to it, indicating that "new" updates will be installed on shut down. But, of course, they'll fail and when the PC is restarted, the shield icon is still there. When checking the update history and viewing the details of the failed updates, I get the following: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) Installation date: ?6/?29/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important A security issue has been identified leading to MFC application vulnerability in DLL planting due to MFC not specifying the full path to system/localization DLLs. You can protect your computer by installing this update from Microsoft. After you install this item, you may have to restart your computer. More information: http://go.microsoft.com/fwlink/?LinkId=216803 and: System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Installation date: ?6/?28/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important This tool is being offered because an inconsistency was found in the Windows servicing store which may prevent the successful installation of future updates, service packs, and software. This tool checks your computer for such inconsistencies and tries to resolve issues if found. More information: http://support.microsoft.com/kb/947821 About My System I'm running Windows 7 Home Premium 64-bit. This is a custom PC build and the OS was installed fresh, not an upgrade from a previous version. I've been running this system for about four months. Windows Updates aside, the system is usually quite stable.

  Read the article

• Dead Linux server - need help and options

  - by Choi S.

  All, I have a Dell PE 1950 w/ 2 SATA drives in a software RAID1. OS is CentOS 5.5 (2.6.18.x). Starting this afternoon we received HW errors (something on the bus is bad, E171F) and the machine became unresponsive. We hard booted and it came back up for about 5 hours but then it happened again. I'm trying to figure out our options. Unfortunately we do not have similar hardware but I have a small desktop that I can use. I was contemplating putting one of the drives into the desktop and then starting it up. My goal was to then P2V it using Vmware converter but apparently the free v5.x doesn't support hot cloning/converting on a RAID volume, only the Enterprise 4.x version of Converter does. My questions are: 1.) Is putting a single drive out of a RAID1 pair into another piece of HW is safe? Based on my research and understanding it appears to be but would like confirmation. 2.) Is there any work around to the Vmware Converter not supporting RAID volumes during a hot clone/convert session? 3.) Are there other options I'm overlooking? Thanks in advance for reading and responding. --Choi S.

  Read the article

• file system that allow to specify different RAID level per directory and change it afterward

  - by Adam Ryczkowski

  I have 5 hard drives, where I want to keep my data. Some of my files are more important, and some of them are less. So some of them I wish to put on RAID-6, and for some it RAID-5 is sufficient. It is difficult to predict at the moment of creation of the arrays how much space of each type to declare. What I would do if I didn't hear about zfs, is partition the hard drives into identical 100GB partitions, and as my needs grow, assemble those partitions into md devices using linux-raid. Then, I'd combine those devices using lvm into logical volumes where I'd put my data. So when I'd need more space of e.g. RAID-6, I'd take 100GB partition from each hard drive and assemble them into another RAID-6 md device and would use it as physical storage for the logical volume group dedicated for RAID-6 data. Then I could grow the file system on this logical volume. On top of RAID-6 and RAID-5 Volume Groups (managed by lvm) would reside completely independent file systems, which I'd later merge with multiple mount --bind into a single directory structure that would reflect the logical structure of data rather that of the storage. But now, when I heard about the ZFS with all the performance, data-healing and compression capabilities I cannot stop thinking if it can help me. If so, what do you think would be the best setup?

  Read the article

• Log backups "stalling" on SQL 2008?

  - by MattK

  I have interited a box running SQL Server 2008 and Windows 2003, and have had a few events where largeish (35GB) log backups "stall", both before and after the installation of SQL 2008 SP1. The server log ships to a standby, so regular log backups are taken at 15 minute intervals. However, after an index reorg causes the log to grow to about 35GB (on a DB with about 17GB of data), the next log backup runs to ~95% completion, then seems to stop. The process shows as suspended, with a wait state of BACKUPIO. CPU, read, and write activity on the SPID also does not change, and the process stays in this state for hours, when normally a backup of this size should complete in about 20 minutes. This server has a single RAID-1 volume, thus the source database files and destination backup files are on the same volume. However, I cannot determine if another process is blocking the backup. The backup SPID cannot be killed, and the only way to terminate the log backup and clear the lock on the backup file is to cycle the SQL Server service. There was one event where the backup terminated completely, with an error that another process had locked the backup file, but no details about what that process was. Can anyone suggest a cause or diagnostic process to this situation?

  Read the article

• HP/IBM alternative to Buffalo iSCSI TerraStation?

  - by Robin Day

  I'm looking at virtualising some of our infrastructure in order to allow for more resiliance and future expandability. We have successfully virtualised on single servers with Direct Attached Storage and are now looking for a more future proof solution using a high powered host (or two) and a SAN (or two). I'm thinking that the host machine will probably be an HP ProLiant DL360 G7 (all of our exisiting infrastructure is HP). Unfortunately, I am new to the world of SANs. From what I can see, the Buffalo Terrastation III is all I would need in order to setup an iSCSI SAN for VMWare to use. However, I'm a little reticent to go that way as it's a bit too "entry level" for my liking. In particular I would be very keen for more redundancy, power, networking, etc. I'm also very aware that you "get what you pay for". Therefore, can anyone reccommend equivalents from the big boys? HP/IBM? I have searched high and low on the HP site and seen many options but am struggling to work out if it is all the hardware I will need. Some options appear to need separate controllers from disk enclosures, etc.

  Read the article

• DVI output only working on Windows, not during booting or on Linux

  - by Mononofu

  So yesterday I booted my laptop up and the external monitor I have it connected to just stayed black. At first, I thought the problem would go away when Ubuntu was loaded, but it didn't. I tried to reboot a few times, to no avail. Then I decided to give Windows 7 a try, and suddenly (at the login-screen), my external monitor turned on and worked like normal. I have connected the monitor via DVI, and this only seems to work with Windows now. I don't even get a signal in my BIOS! Mind you, everything was working fine before that, and I didn't change a single thing. I then tried to connect the monitor via VGA (from my DVI jack, which can output VGA using an adaptor), and it worked again. However, 1920x1200 using VGA looks like crap - black print on white background is basically illegible. Do you have any ideas how to fix this peculiar problem? I only use windows for gaming, so it's no real help that it still works normally. Please also excuse any spelling mistakes, I am practically typing this blindly. Edit: I only have one graphics card in my laptop, and I can't select anything related to that in my BIOS. In fact, I can pretty much do almost nothing there. My laptop is a Nexoc Osiris E703, graphics gard is a GeForce Go 7900 GTX. As I mentioned before, DVI output during booting and on Ubuntu was working fine for years before yesterday!

  Read the article

• Deploying multiple identical copies of a virtual machine for compute tasks

  - by Reid

  I have a compute task which has a large number of library dependencies. I would like to deploy it on some of my company's large Linux clusters, where I do not have root. I could probably track down, compile, and install the right versions of all the libraries, but this looks to be quite tedious and would have to be repeated if I deployed it again somewhere else. On the other hand, it's pretty easy to install on current Ubuntu. This led me to wonder about a virtual machine approach. Could I put together a virtual machine which booted up, ran the computation (with parameters from and results to the host), and then shut down? In other words, I'd like a command like this that I could run on the host: $ ./run-vm --ram N --task /path/on/host/foo.sh --results /another/host/dir/ This would boot the VM, run foo.sh, and put the (relatively small) results of the computation in /another/host/dir/. It's important to start up many instances of the VM simultaneously, both on a single node and multiple nodes of the cluster. So it would be nice if I didn't have to make many copies of the VM virtual disk and metadata. As the task instances are completely independent, the VMs would not need any network support once deployed, or any outside communications beyond reading and writing the host filesystem. Is this possible, and if so, how might I go about doing it? Are there assumptions I've made above which are bogus?

  Read the article

• How to use a common library of environment variables among different languages?

  - by JDS

  We have three main languages with which we perform system tasks: Bash, Ruby, and PHP, and Perl. Four, four main languages. We use managed environment variables to provide authorization info that automated scripts need. For example, a mysql user account and password. We'd like to use one single managed file to maintain these variables. In some instances, for example, in cron, these environment variables are not available. They are made available in CLI scripts because we source the env file in everyone's profile. But something like cron doesn't do that. On the CLI, when the env file is sourced, any given script can access those variables. Bash has them directly, PHP in $_ENV, ruby in ENV, etc. We can't source the file into non-Bash scripts, because most languages implement shell commands by running them in a subshell. We considered parsing the Bash, converting to the script's lang, and running the equivalent of "exec(parsed_output)" on the resulting strings. What is a good solution to providing managed environment vars to scripts running in cron, or similar?

  Read the article

• VPN service into 192 network

  - by tophersmith116

  I'm thinking about setting up a security testing lab. I work on a switched network, and that just makes for unnecessary headaches when doing testing. I'd like to create a 192 network with a few machines inside for DBs and AppServers etc. I will need a pivot machine that connects to both the outer network and the 192 (for automation purposes). But I'd like to be able to connect into the 192 network with my own machine from the outer network as the "attacking" machine (rather than have dedicated attack machines inside the 192 network). Therefore, I'd like to have the pivot server be a VPN server as well, so that my machine can VPN into the 192 network from the outer network. First off, is this even possible? Can I have a single computer with two NICs where a VPN service allows remote connections into the 192? Secondly, I'd like to have multiple outer clients connect to the VPN. Does anyone have any suggestions? I've used Hamachi well before, but I've also seen some good stuff from OpenVPN.

  Read the article

• 3 Monitor PCI-e Graphics card on Linux (without tremendous pain)?

  - by N Rahl

  As we are all painfully aware, the only way to get multiple monitors AND compositing (Compiz) on Linux is to use a single graphics card that can drive both (or in my case all three) screens. I bought a Radeon 5750 specifically because it claims to able to drive 3 monitors. I can plug in 3 monitors (2 DVI, 1 HDMI) and the Catalyst Control Center shows all 3, but only 2 can be enabled at a time. The exact message is: The current settings cannot be applied. Possible issues may include: - Display(s) cannot be enabled. - Setting(s) cannot be applied due to insufficient video memory. So I'm going to assume that either the 5750 doesn't support 3 monitors, OR, more likely, ATI couldn't be bothered to add that support to their Linux drivers. So this is a multipart question: First, can anyone suggest a PCI Express Graphics card that can run 3 screens on linux without tremendous pain? I'm looking for something where you install the driver and all three screens "just work". Does such a card exist? Second, if you have a 5750, have you been able to get it to do 3 monitors? I'm running Ubuntu 10.04 at the moment.

  Read the article

< Previous Page | 552 553 554 555 556 557 558 559 560 561 562 563  | Next Page >