Search Results

Search found 20592 results on 824 pages for 'anything'.

Page 559/824 | < Previous Page | 555 556 557 558 559 560 561 562 563 564 565 566  | Next Page >

• Can't remotely connect through SQL Server Management Studio

  - by FAtBalloon

  I have setup a SQL Server 2008 Express instance on a dedicated Windows 2008 Server hosted by 1and1.com. I cannot connect remotely to the server through management studio. I have taken the following steps below and am beyond any further ideas. I have researched the site and cannot figure anything else out so please forgive me if I missed something obvious, but I'm going crazy. Here's the lowdown. The SQL Server instance is running and works perfectly when working locally. In SQL Server Management Studio, I have checked the box "Allow Remote Connections to this Server" I have removed any external hardware firewall settings from the 1and1 admin panel Windows firewall on the server has been disabled, but just for kicks I added an inbound rule that allows for all connections on port 1433. In SQL Native Client configuration, TCP/IP is enabled. I also made sure the "IP1" with the server's IP address had a 0 for dynamic port, but I deleted it and added 1433 in the regular TCP Port field. I also set the "IPALL" TCP Port to 1433. In SQL Native Client configuration, SQL Server Browser is also running and I also tried adding an ALIAS in the I restarted SQL server after I set this value. Doing a "netstat -ano" on the server machine returns a TCP 0.0.0.0:1433 LISTENING UDP 0.0.0.0:1434 LISTENING I do a port scan from my local computer and it says that the port is FILTERED instead of LISTENING. I also tried to connect from Management studio on my local machine and it is throwing a connection error. Tried the following server names with SQL Server and Windows Authentication marked in the database security. ipaddress\SQLEXPRESS,1433 ipaddress\SQLEXPRESS ipaddress ipaddress,1433 tcp:ipaddress\SQLEXPRESS tcp:ipaddress\SQLEXPRESS,1433

  Read the article

• Exim rejects recipient address on my domain

  - by Nicolas

  Hi, I have a dedicated server (debian) on which I have installed Exim and Dovecot. Everything worked fine until around a month ago. I tried to reinstall and reconfigure exim but I keep having all the incoming emails rejected. Outlook says: A message that you sent could not be delivered to one or more of its recipients. This is a permanent error. The following address(es) failed: [email protected] SMTP error from remote mail server after RCPT TO:: host mail.mydomain.com [94.76.##.##]: 550 relay not permitted GMAIL: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550 relay not permitted (state 14). On the server side, my rejectlog file shows: 2011-01-04 17:09:21 H=mail-qw0-f53.google.com [209.85.216.53] F=<####@gmail.com rejected RCPT : relay not permitted ... and the mainlog file: 2011-01-04 17:00:01 1PaAEr-0007vN-DX <= root@ETC_MAILNAME U=root P=local S=869 2011-01-04 17:00:01 1PaAEr-0007vN-DX ** root@etc_mailname: Unrouteable address 2011-01-04 17:00:01 1PaAEr-0007vY-Kn Error while reading message with no usable sender address (R=1PaAEr-0007vN-DX): at least one malformed recipient address: root@ETC_MAILNAME - malformed address: _MAILNAME may not follow root@ETC 2011-01-04 17:00:01 1PaAEr-0007vN-DX Process failed (1) when writing error message to root@ETC_MAILNAME (frozen) 2011-01-04 17:09:21 no IP address found for host MAIN_RELAY_NETS (during SMTP connection from mail-qw0-f53.google.com [209.85.216.53]) 2011-01-04 17:09:21 H=mail-qw0-f53.google.com [209.85.216.53] F=<####@gmail.com rejected RCPT : relay not permitted then after the message becomes frozen: 2011-01-04 17:28:44 1PaAEr-0007vN-DX Message is frozen Thank you for your help, any idea/comment is welcomed as I am really running out of idea to fix this issue, Nicolas. Oh and the PHP mail() function does not do anything as well, would it be linked to? I think mail() uses sendmail from my php.ini.

  Read the article

• XDEBUG/PHP doesn't dump profile even when set up properly?

  - by John D.

  I installed xdebug from source, but also tried my package manager (separately) and they both are loaded correctly (verified by restarting Apache and seeing the xdebug copyright info in phpinfo()) but they do not dump profiling information. Out of the 40 different attempts of configuration it logged once or twice but I lost what I did, I tried with first only loading the module in php.ini with no settings, but it didn't log to /tmp/. I tried many different settings but my current is now: xdebug.profiler_enable = Off xdebug.profiler_enable_trigger = 1 xdebug.profiler_output_dir = "/tmp/" xdebug.profiler_output_name = "profiler.%t" Of course I call my script through 127.0.0.1/test.php?XDEBUG_PROFILE, which is for enable_trigger. Do you know why it would not dump profiler information? nobody (Arch Linux) can write to /tmp/ as it has before, so I'm sure it is not a permissions error. Apache's error_log does not tell me anything about xdebug either, as it has loaded correctly. It just does not "work"! EDIT: I made a subfolder "xdebug_profiles" in /tmp/ and chown'ed it to nobody, and now it works flawlessly. I'm not sure why it couldn't write before, I guess it's just a caveat with nobody on Arch. I answered my own question , not enough points to answer it or comment, so consider this answered.

  Read the article

• Windows XP SP3 client over NAT to a Windows 2008 R2 SP1 file server disconnection

  - by Patrick Pellegrino

  we just transferred a pilot group from our old(!!) Netware infrastructure to an Microsoft infrastructure. Since then, our users got problems accessing their files. They all experience disconnection from the mapped drives. The file server is access via a WAN connection by a firewall (Sonicwall) between both network and we do NAT. All clients have Windows XP SP3 and the file server is an Windows 2008 R2 SP1. On the file server I got many Event Id 2012. Many post over the Internet suggested a problem between the SMB protocol and NAT. We need a short term fix to continue to transfer users from Netware to Microsoft after what will work to remove the NATing. I found this MS KB http://support.microsoft.com/kb/2444558 that suggested a kind of workaround for Windows 7 clients but I can found anything for Windows XP. Anyone can help me with this ? We don't want to stop the project and do a network job before migrating. Regards. Update: Our few Windows 7 computers doesn't seem to have this issue.

  Read the article

• r1soft agent is failing with the error: "write error while sending code: Broken pipe"

  - by curiousguy

  I have an Ubuntu 10.04.4 LTS server with r1soft agent installed in it. Recently, the backups are failing with the following error. -------- write error while sending code: Broken pipe -------- I have reinstalled the buagent but to no avail. On checking the server logs, I could see the following errors listed in it: -------- # tail -f /var/log/messages |grep -i buagent Nov 17 03:35:06 microscope buagent: Need to back up 126 sectors Nov 17 03:35:06 microscope buagent: (Righteous Backup Linux Agent) 1.79.0 build 12433 Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.195) with valid RSA key Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.201) with valid RSA key Nov 17 03:35:06 microscope buagent: sending auth challenge for allowed host at (10.128.136.201) port (47890) Nov 17 03:35:06 microscope buagent: host (10.128.136.201) port (47890) authentication successful Nov 17 03:35:06 microscope buagent: Backup request accepted. Starting backup. Nov 17 03:35:06 microscope buagent: Snapshot completed in 0.010 seconds. Nov 17 03:45:03 microscope buagent: Error reading blocks from snapshot. Nov 17 03:45:03 microscope buagent: Reading blocks failed Nov 17 03:45:03 microscope buagent: error backup aborted Nov 17 03:45:03 microscope buagent: backup failed on agent closing connection Nov 17 03:45:03 microscope buagent: Backup failed. Nov 17 03:45:03 microscope buagent: write error while sending code: Broken pipe (32) Nov 17 03:45:03 microscope buagent: tell child write failed -------- I tried changing the 'Timeout' and 'DiskAsPartition' value in '/etc/buagent/agent_config' file but no luck. Also, verified that proper route is added to the backup server. The agent is also running fine. Am I missing anything? Any help would be much appreciated. Note: CDP 2.0 is installed in the backup server.

  Read the article

• Virtualbox HTTP load testing, host CPU overload issues

  - by aschuler

  I'm doing HTTP load testing benchmarks (using Apache Benchmark and Siege) on a small Java EE 1.7.0 / Tomcat 7.0.26 application running on a Debian Squeeze 6.0.4 x64 virtualized with Virtualbox 4.1.8. The computer host is Ubuntu 11.10 x64. I've modified those parameters in the Tomcat server.xml : <Connector port="8080" protocol="HTTP/1.1" connectionTimeout="200000" redirectPort="8443" acceptCount="2000" maxThreads="150" minSpareThreads="50" /> The application executed on the server takes around 300ms. This app is running well until a certain amount of concurrent connections like those one : ab -n 500 -c 150 http://xx.xx.xx.xx:8080/myapp/ ab -n 1000 -c 50 http://xx.xx.xx.xx:8080/myapp/ siege -b -c 100 -r 20 http://xx.xx.xx.xx:8080/myapp/ A lot of socket connection timed out happens and this completly overload the host processor (but the CPU load inside the VM is normal). Doing an htop on the host, i can see that the Virtualbox processus is running under 300% CPU and never come down even after the load test is finished. (I've allocated 4 processors to the VM, if I allocate only one processor, CPU load goes under 100%). Restarting Tomcat don't do anything, i'm forced to restart the whole VM. I've tryed to launch those ab/siege commands locally on the VM and everything goes well. I first thought it was related to a linux network limit as explained here: Running some benchmarks using ab, and tomcat starts to really slow down So I've modified those TCP parameters : echo 15 > /proc/sys/net/ipv4/tcp_fin_timeout echo 30 > /proc/sys/net/ipv4/tcp_keepalive_intvl echo 1 > /proc/sys/net/ipv4/tcp_tw_recycle echo 1 > /proc/sys/net/ipv4/tcp_tw_reuse It seems to be better, but it continues to overload the host CPU and output socket connections time out at a certain amount of concurrent connections. I'm wondering if this is not related to how Virtualbox handles external concurrent connections.

  Read the article

• Selenium server causes crazy load on server - how to prevent?

  - by Eric

  I'm running this linux: Linux host.themepark.com 2.6.32-220.4.1.el6.x86_64 #1 SMP Tue Jan 24 02:13:44 GMT 2012 x86_64 x86_64 x86_64 GNU/Linux And I run the Selenium stand-alone server on my box with this command: java -jar /home/l/cron/selenium-server-standalone-2.24.1.jar > /logs/selenium.log 2>&1 & Here's the problem: as soon as I do that, the server load starts skyrocketing. I even went back and downloaded older versions of the Selenium server, but same results with 2.23.1, 2.23.0, and 2.19.0. Note that the server load starts going nuts before I issue ANY commands to Selenium or do anything else. All I'm doing is firing up the server, per the command above. This used to work perfectly on my server without causing massive server load, so something has changed, but I'm not sure what. My server is a managed VPS so I don't know if there is some kind of auto-update script that kicked in or what... but it's a problem. (Incidentally, even though the server load climbs like crazy, everything still works: after firing up Selenium, my server creates a screen with Xvfb so Firefox will be happy, then a PHP script talks to Selenium to do what it needs to do before shutting everything down. It takes a LONG time, and the load gets all the way up to 8 [!!!] before it is finished, which kills my web server and makes the main site horribly unresponsive... but it does get everything done.) Any suggestions for what is going on, why it's started doing this and/or, most importantly, how I can make Selenium not kill the server when it starts up... would be GREATLY appreciated!

  Read the article

• problem booting crusty old windows XP

  - by Carson Myers

  I have an acer aspire laptop running Windows XP home. I believe I have some virus on it, I'm not sure--I mostly just run linux in a VM on it so I wasn't too worried. I'm not sure if that virus caused this problem. The laptop wasn't recognizing my USB hard drive for some reason so I decided to restart it. When it started up, it got past the memory test, past the boot screen, (but it paused right here on a blank screen for awhile) and flashed the desktop once (like it does just before the login screen) and then crashed. I got a quick BSOD and then it restarted. Then it tried to boot again, etc etc infinite loop of failure. Well, before trying safe mode, I disabled automatic restart on system crash so I could read the blue screen. There wasn't anything important on it, it said *** STOP: 0x00000000 (0xC0000000 0x,.... ) beginning physical memory dump physical memory dump complete That's not verbatim (obviously) but it didn't help me. so I booted in safe mode, and it stopped on the driver gagp30kx.sys and then restarted (and infinite loop of failure again). I burned a recovery CD and tried that. It loaded it, and I went into repair mode. I ran chkdsk and then disabled the AGP driver. Same thing on booting in safe mode except it stopped at mup.sys instead. I enabled the AGP driver again, and ran chkdsk again from the CD. It said it found problems but didn't say it fixed them. So I ran it a second time, and it said "performing additional checking or recovery" lots of times (I can't tell how many, they went above the screen top). I tried booting again and no luck. Every time I run chkdsk after trying to boot again it says it found and fixed more errors. I think it might be whatever driver is after the AGP driver, but I don't know what it is or how to find out. Can anyone help me fix this?

  Read the article

• Firefox Won't Save My Google Cookies Between Restarts

  - by Tom Purl

  I'm using firefox 11 on Ubuntu. For some strange reason, Firefox won't save my google cookies between browser restarts. I have to log in to gmail every time I restart my browser, even if I click on the check box that tells Google to remember me. The strange thing is that Firefox does actually store some gmail cookies when I log in. It's just that those cookies disappear after restarting Firefox. The especially strange thing is that this only seems to happen with *.google.com url's. I haven't noticed this problem with any other site that I use. Please note that I tried to see if this was a plugin-related problem. I therefore started Firefox in safe mode and turned off all plugins. I then logged into Gmail and told it to remember me. I then shut down Firefox and started it the same way in safe mode. I got the same bad results. Has anyone else ever seen anything like this before? Is there a reason that Firefox seems to be blacklisting Google cookies?

  Read the article

• ASA DHCP Relay configuration..

  - by Jeff

  I have locations in different cities, connected using 2 Cisco ASA devices. my main location, corporate, use the IP 192.168.1.x The second location, remote store, use the IP 192.168.3.x I have a DHCP server (192.168.1.254) at my corporate location. I have created a scope for the 192.168.1.x which works fine for the corporate location. I created a scope for the remote location (192.168.3.x) on my DHCP server and tried to configure the remote ASA DCHP Relay, on the remote ASA: I disabled the DHCP Server on the inside. I enabled DHCP Relay on the inside, with set route set at yes. I set the Global DHCP Relay Servers, specify up to four servers to which DHCP requests would be relayed. I added my DHCP, 192.168.1.254 I flashed these settings to the ASA and gave it a try, didn't do anything. am i missing something - forgetting something. not really sure what im doing wrong. DHCP Settings on remote ASA: dhcp-client update dns server both dhcpd dns 192.168.1.254 dhcpd ping_timeout 750 dhcpd domain JEWELS.LOCAL dhcpd auto_config outside dhcpd update dns both ! dhcpd address 192.168.3.2-192.168.3.33 inside ! dhcprelay server 192.168.1.254 outside dhcprelay enable inside dhcprelay setroute inside on my local ASA: i have two ACLs for UDP ports 67 and 68 permitting any inbound traffic from the remote locations IP ... dhcprelay timeout 120

  Read the article

• Windows 7 Backup - Does the "system image" include all the files on my drive?

  - by Vaccano

  I have a new Dell Laptop that I have setup the way I like it. I want to use Windows 7 to do a backup and then restore that backup on a different hard drive (solid state). When I setup the backup info (manually) for Windows 7 Backup there is a little checkbox at the the bottom that says: Include a system image of drives: RECOVERY, OS (C:) I can also select to backup all my data on the C: drive (the only hard drive I have anything on) as well as some libraries (which are on my C: drive so no point in selecting those). The question I have is, does Windows 7 Backup just somehow know what needs to be restored (ie program files and Windows and the registry ....? Or is it really making a full restorable copy of the C: drive? (If the later is true then I don't need select the C: drive to be "backed up" if I don't plan to access the files except by restoring them right? (Because the system image will already have it all.)) So, which way is it? What is saved in the System Image?

  Read the article

• What is the advantage of not running as root? [closed]

  - by Shmuel Brill

  Possible Duplicate: What's wrong with always being root? All modern brands of Linux highly discourage (or disable) one from running as root instead of a normal user. I do not understand why. As a "normal" user, one could Download a rouge program from the internet. Run it (After all, one isn't root, what can it do). It installs itself in .bashrc or .xinitrc It writes a rouge "sudo" and "su" and adds . to the path Not noticing that . is in path, one runs sudo. The rouge program now has root password and can do anything it wants in the system. Even if 3-6 doesn't happen, the program could still Be part of a botnet. Read all files in the home directory and send them back (mine for SS#, Credit Card numbers, bank account numbers, etc). Send spam. Run a backdoor server to allow an attacker a chance to connect to the machine to determine vulnerabilities. It seems that the whole "permissions" thing (root/non-root) is just to prevent amateur crackers from getting into the system, so the question is: Is there a point in avoiding running as root, and is there a way to protect oneself if one wants to run unsafe code?

  Read the article

• Cisco SG 300-28P PoE switch appears to have damaged my domain server's network IF

  - by cdonner

  I just replaced the old HP ProCurve switch with a new Cisco SG 300-28P managed switch. It has PoE on all ports. Everything works, except for my domain server that went offline and the network interface appears to be dead. Windows says the network cable is disconnected, and no lights blink on the switch. Tried different cables and different ports on the switch. The Cisco PoE ports are supposed to be auto-sensing, i.e. not to send power to a device that cannot handle it. Is this technique not 100% reliable? The server is a SHUTTLE XS35V2 with an onboard network chip, so it is probably fried. My questions: is this plausible? who's fault is it - Shuttle or Cisco (i.e. which support line should I try first)? UPDATE: I did go back and tried another switch between the server and the Cisco switch, and indeed, the connection came back to live. When everything is powered down and I start fresh, with the server connected to the Cisco switch, the port light will blink for a while and the connection status is "No Internet connection" at first until it goes off after about 20 seconds and the connection status changes to "Network cable disconnected". On the other switch it works. Clearly not a PoE issue now. I will start looking into the Cisco's onboard diagnostic functions, but so far I have not noticed anything unusual in the log.

  Read the article

• IIS 7.0 404 Custom Error Page and web.config

  - by Colin

  I am having trouble with a custom 404 error page. I have a domain running a .NET proj with it's own error handling. I have a web.config running for the domain which contains: <customErrors mode="RemoteOnly"> <error statusCode="500" redirect="/Error"/> <error statusCode="404" redirect="/404"/> </customErrors> On a sub dir of that domain I am ignoring all routes there by doing routes.IgnoreRoute("Assets/{*pathInfo}"); in the .NET proj and I want to put a custom 404 error page on that and any sub dir's of Assets. The sub dir contains static content like images, css, js etc etc. So in the Error Pages section of IIS I put a redirect to an absolute URL. The web.config for that dir looks like the following: <system.webServer> <httpErrors> <remove statusCode="404" subStatusCode="-1" /> <error statusCode="404" prefixLanguageFilePath="" path="http://mydomain.com/404" responseMode="Redirect" /> </httpErrors> </system.webServer> But I navigate to an unknown URL under that dir and yet I still see the default IIS 404 page. I am also seeing an alert in IIS that reads: You have configured detailed error messages to be returned for both local and remote requests. When this option is selected, custom error configuration is not used. Does this have anything to do with the customErrors mode="RemoteOnly" in the site web.config? I have tried to overwrite the customErrors in the sub dir web.config but nothing changes. Any help would be appreciated. Thanks.

  Read the article

• pfsense 2.0.1 Firewall SMB Share not showing up under network

  - by atrueresistance

  I have a freenas NAS with a SMB share running at 192.168.2.2 of a 192.168.2.0/28 network. Gateway is 192.168.2.1. Originally this was running on a switch with my LAN, but now having upgraded to new hardware the Freenas has it's own port on the firewall. Before the switch the freenas would show up under Network on a windows 7 box and an OSX Lion box as freenas{wins} or CIFS shares on freenas{osx} so I know it doesn't have anything do to with the freenas. Here are my pfsense rules. ID Proto Source Port Destination Port Gateway Queue Schedule Description PASS TCP FREENAS net * LAN net 139 (NetBIOS-SSN) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 389 (LDAP) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 445 (MS DS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 137 (NetBIOS-NS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 138 (NetBIOS-DGM) * none cifs lan passthrough BLOCK * FREENAS net * LAN net * * none BLOCK * FREENAS net * OPTZONE net * * none BLOCK * FREENAS net * 192.168.2.1 * * none PASS * FREENAS net * * * * none BLOCK * * * * * * none I can connect if I use \\192.168.2.2 and enter the correct login details. I would just like this to show up on the network. Nothing in the log seems to be blocked when I filter by 192.168.2.2. What port am I missing for SMB to show up under the network and not have to connect by IP? ps. Do I really need the LDAP rule?

  Read the article

• How to use connectify to share files between 2 laptops, one running Windows 7?

  - by p2pnode

  I have 2 laptops one running XP and another Windows 7. Both have WiFi-card installed. I want to be able to share files between these 2 machines and then in next step also be able to share internet connection. I have heard that Connectify on Windows 7 is a very handy and easy tool to set up a hotspot and other machines even XP,Vista can connect to this host hotspot and share files and internet connection. I am able to search for the network (set on host) on my client machine. But how to share files? I don't see any such menu or anything. Also after I have installed connectify on Windows 7, I am not able to connect to internet using data card. It throws error that "Error 31:A A device attached to the system is not functioning". And on client machine, if I connect to data card, as well as connect to wireless network setup by host machine, I no longer am able to access internet, even though the data card is connected. The browser throws error: Please help. Any other utility similar to connectify etc?

  Read the article

• hMail server - sending copy of an e-mail changing the sender

  - by Beggycev

  Dear All please help me with following request. I am using hMail server in a company(test.com) and have several hundred of guest e-mail accounts ([email protected]). I need to accomplish this: When any of the guest e-mails receives a message(either from internal or external sender) this e-mail(or its copy) is sent to another address "[email protected]" which is the same for all of these guest e-mails. But I need the sender to be identified as the [email protected] not as the original sender which happens when I use forwarding. I tried to prepare a simple VBS script using the OnAcceptMessage event to accomplish this. and it works on my testing machine without internet connectivity but not in the production environment. To be specific, if I send an e-mail to [email protected] in my test env it is delivered to the [email protected] with [email protected] being a sender. But in the production env the e-mail stays in the guest mailbox with the original sender. I am interested in any solution, using a rule in hMail or script, anything is welcome. Thank you for any help! The script: Sub OnAcceptMessage(oClient, oMessage) 'creating application object in order to perform operations as hMail server administrator Dim obApp Set obApp = CreateObject("hMailServer.Application") Dim adminLogin Dim adminPassword 'Enter actual values for administrator account and password 'CHANGE HERE: adminLogin = "Admin_login" adminPassword = "password" Call obApp.Authenticate(adminLogin, adminPassword) Dim addrStart 'Take first 5 characters of recipients address addrStart = Mid(oMessage.To, 1, 5) 'if the recipient's address start with "guest" if addrStart = "guest" then Dim recipient Dim recipientAddress 'enter name of the recipient and respective e-mail address() 'CHANGE HERE: recipient = "FINAL" recipientAddress = "[email protected]" 'change the sender and sender e-mail address to the guest oMessage.FromAddress = oMessage.To oMessage.From = oMessage.To & "<" & oMessage.To & ">" 'delete recipients and enter a new one - the actual mps and its e-mail from the variables set above oMessage.ClearRecipients() oMessage.AddRecipient recipient, recipientAddress 'save the e-mail oMessage.save end if End Sub

  Read the article

• Hosting a javascript api file for third party sites the way sharethis, uservoice, analytics do it.

  - by Dayson

  I'm preparing to launch a service soon which will provide third party websites a widget. The widget requires my javascript file in the website's code. Exactly the same way services like analytics, uservoice, sharethis, getclicky, etc provide you with a javascript snippet to add to your page. Therefore, my javascript file is going to be hotlinked by tons of websites which possibly receive a lot of requests too. I need advice/opinions on the following aspects: What's the right location for hosting this file? Should I use a sub-domain for it? I was thinking of something like http://api.myservice.com/js/foo.js . Remember, once websites start embedding this file, its location CANNOT change under any circumstances. Right now we can afford just one dedicated server. So I have minified my file, enabled gzip and plan to use some good cache control headers through apache. Also, in the near future when the requests pickup, I will use a http proxy like Varnish. Is this a good plan for the near future? Should I be considering a CDN in the future (since we can't afford it now)? If so how do I make sure we're prepared to migrate to it without breaking services. Pros/Cons of moving just this file to a CDN? Also, since its just one javascript file(50kb), any affordable CDN so we could consider it in the beginning itself? Any other word of advice I could use? Anything I shouldn't overlook at this stage which I would regret later? (both in terms of server + javascript ajax limitations) Thanks in advance.

  Read the article

• ESXi 4.0 Guests Locking up

  - by Brendan Sherwin

  I installed ESXi 4.0 on an HP Proliant g5 with a 64bit Xeon processor and took advantage of the free license as I work for a public school. I created two instances of server 2003 from scratch, one to be the DC, DHCP, the other to be a file server and DNS/DHCP backup. I had both guests up and running fine, setup my user accounts, transferred the data, etc etc. Once I joined a client machine to the domain, I would find that both of my Windows guests would lock up. Sometimes it would be for five or so minutes, once it was overnight. The "locked up" state means that as far I could tell, all services were stopped; dhcp no longer handed out IP's, DNS stopped working, I couldn't RDP into the server. The ESXi host, my HP server, was still running fine. VSphere was working, and I could look at the performance of the individual guests.I would try Powering off the hosts from inside VSPhere, and the hosts would start powering off, but get stuck at 95%, and stay that way, sometimes only for 10 minutes, others for hours. Several times I had to restart ESXi from it's console in order to restart my machines. Now, can anyone tell me what is happening, and how I can fix it, or take steps to prevent it? I hired a consultant to come take a look at it, someone who's experience and knowledge I trust, and he told me he had never seen anything like this ever before. He spoke to a friend of his who is VM certified, and he also said he had never heard of this issue. Thanks for your replies, and I'll do my best to respond ASAP. Currently, the server is powered off, and I've reinstituted my nine year old Server 2000 boxes, and I'm considering installing ESXi 3.5. Does anyone know a host created in 4.0 will work in 3.5? I'd really like to avoid having to rebuild those accounts! I know 4.0 works on this server, as I have another server in another school with the same exact hardware running 4.0 fine. Brendan

  Read the article

• BOOTMGR is compressed

  - by JavaAndCSharp

  So I've just finished messing up my computer beyond repair. I originally had a Windows 7 install on my 64GB SSD and all my data on my 1.5TB HDD. So I decided to install Windows 8 Consumer Preview. I tried to clone my 64GB SSD onto my HDD; but that didn't work either at first. I later learned that it wiped all my data off of it. Thank goodness for the cloud. So I retried the cloning after I realized that my data was gone, and I finished it. So I rebooted and got a cryptic error message: BOOTMGR is compressed. Press Ctrl+Alt+Del to restart. So I did. Several times. I followed the instructions to rebuild the bootmanager from many websites, including HowToGeek, smallvoid.com, and more. None worked. BTW, I've lost my Windows 7 Professional DVDs. All I have is my Windows 7 Home Premium DVD. It's the one I got with my laptop. How can I get back to a working computer? I'm willing to wipe anything, as my data is all in the cloud.

  Read the article

• Should I upgrade to Symantec Endpoint Protection? [closed]

  - by Alex C.

  I'm the IT manager at an animal shelter in Upstate New York. We have a Windows network with about 50 desktops running Windows XP Pro. We used to use CA eTrust Antivirus, but that product didn't work too well (too many infections got through). About six months ago, we switched to using Symantec Antivirus Corporate Edition ver. 10.1.8.8000. If anything, the Symantec product is even worse. The last six weeks in particular have been very bad -- we've had about seven or eight PCs get hit with those malware infections that masquerade as antivirus software. In most of those cases, Symantec didn't even flag the malware at all. So... what gives with the Symantec Antivirus? As far as I can tell, it's installed correctly and downloading updated definitions nightly. I can upgrade to Symantec Endpoint Protection for $220 (we get non-profit pricing), but I don't want to do it if it's not going to be significantly better. Any advice? Should I switch to something else entirely? Thanks!

  Read the article

• SQL Server Express Failed to Install

  - by JasCav

  I am attempting to install SQL Server Express (as part of the Visual Studio 2010 Professional installation), but it is failing. I am receiving this error log. [06/22/11,16:31:39] Microsoft Visual Studio 2010 Professional - ENU: [2] UpdateFileFetcherFromMsi: Warning: Missing fwlink entry for cabinet: #SP.cab [06/22/11,16:31:40] setup.exe: [2] Duplicate module ID: {0AFE11CA-57AA-4F66-90BE-284F0F3A5ABD} [06/22/11,16:32:12] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/22/11,16:32:12] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/22/11,16:32:12] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/22/11,17:07:55] Microsoft Visual Studio 2010 Professional - ENU: [2] UpdateFileFetcherFromMsi: Warning: Missing fwlink entry for cabinet: #SP.cab [06/22/11,17:07:55] setup.exe: [2] Duplicate module ID: {0AFE11CA-57AA-4F66-90BE-284F0F3A5ABD} [06/23/11,10:39:33] Microsoft Visual Studio 2010 Professional - ENU: [2] UpdateFileFetcherFromMsi: Warning: Missing fwlink entry for cabinet: #SP.cab [06/23/11,10:39:33] setup.exe: [2] Duplicate module ID: {0AFE11CA-57AA-4F66-90BE-284F0F3A5ABD} [06/23/11,10:40:22] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/23/11,10:40:22] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/23/11,10:40:22] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/23/11,10:53:48] Microsoft Visual Studio 2010 Professional - ENU: [2] UpdateFileFetcherFromMsi: Warning: Missing fwlink entry for cabinet: #SP.cab [06/23/11,10:53:48] setup.exe: [2] Duplicate module ID: {0AFE11CA-57AA-4F66-90BE-284F0F3A5ABD} [06/23/11,13:19:26] Microsoft Visual Studio 2010 Professional - ENU: [2] UpdateFileFetcherFromMsi: Warning: Missing fwlink entry for cabinet: #SP.cab [06/23/11,13:19:26] setup.exe: [2] Duplicate module ID: {0AFE11CA-57AA-4F66-90BE-284F0F3A5ABD} [06/23/11,16:47:36] Microsoft SQL Server 2008 Express Service Pack 1 (x64): [2] Error code -2068643839 for this component is not recognized. [06/23/11,16:47:36] Microsoft SQL Server 2008 Express Service Pack 1 (x64): [2] Component Microsoft SQL Server 2008 Express Service Pack 1 (x64) returned an unexpected value. ***EndOfSession*** I'm reading various articles which point towards something being wrong in the register, but I can't find anything specific. Any suggestions for what I can do to fix this?

  Read the article

• PXE booting LACP hosts on Force10 S50N with FTOS

  - by lolwutreddit

  Hardware: S50N Firmware: FTOS 8.4.2.6 Problem: We're trying to PXE boot some servers that are connected via port-channel interfaces with LACP. Current Work-around: we PXE boot a server with a single interface (eth0), and then use a Perl script to turn up the port-channel interfaces after the server is built. Details: Is anyone doing anything similar on Force10 S50 switches with FTOS? If not, is anyone doing this on another S series, or larger chassis-based Force10? I'm wondering if Native VLAN will solve this, since ports in a port-channel cannot explicitly have a VLAN set, and they don't seem to use the tagged or untagged VLAN that the port channel is in. I will confirm this next (I think it's the only thing I haven't tried) Juniper Example: http://broken.net/openindiana/how-to-pxe-boot-systems-on-lacp-using-juniper-switches/ Cisco: there are plenty of documented ways to solve this issue on IOS and Nexus Update/Edit: since there seems to be no way to use interface or port-channel mode commands to get the individual interfaces to show up in spanning-tree (rtsp in this case), the ports should never go into a forwarding state. I'm not going to mess with it anymore unless a) someone that has experience passes it on, or b) Force10 comes up with a solution for this (I'm guessing it will only be introduced on other S platforms (S55, S60), since the S50 seems to be near EOL). I'm basing that on the fact that the Open Automation type features are only being supported on the newer switches.

  Read the article

• How to Protect Sensitive (HIPAA) SQL Server Standard Data and Log Files

  - by Quesi

  I am dealing with electronic personal health information (ePHI or PHI) and HIPAA regulations require that only authorized users can access ePHI. Column-level encryption may be of value for some of the data, but I need the ability to do like searches on some of the PHI fields such as name. Transparent Data Encryption (TDE) is a feature of SQL Server 2008 for encrypting database and log files. As I understand it this prevents someone who gains access to the MDF, LDF, or backup files from being able to do anything with the files because they are encrypted. TDE is only on enterprise and developer versions of SQL Server and enterprise is cost-prohibitive for my particular scenario. How can I get similar protection on SQL Server Standard? Is there a way to encrypt the database and backup files (is there a third-party tool)? Or just as good, is there a way to prevent the files from being used if the disk were attached to another machine (linux or windows)? Administrator access to the files from the same machine is fine, but I just want to prevent any issues if the disk were removed and hooked up to another machine. What are some of the solutions for this that are out there?

  Read the article

• 0x0000007b WinXP in VirtualBox with no Admin access on source drive

  - by Ozzah

  I have a physical drive with an installation of WinXP-32 which I have made a clone of using SysInternals disk2vhd. I have no admin rights on this installation. I have tried to boot this VHD in VirtualBox, however it blue screens on 0x0000007b. I have researched this and apparently the cause is that Windows doesn't like the IDE controller changing. I have tried all the available controllers in VirtualBox, but they all produce the same result. There is a Microsoft KB article which describes a method involving loading a .reg file and extracting some sys files from a CAB. This method apparently works well for many people with this problem, however it will not work for me as I don't have admin rights on the WinXP installation. Is there anything I can do in this case? Is there any way of loading the .reg file outside the OS? or perhaps doing a repair using the WinXP CD? Even though I have no admin rights on the source drive installation of Windows, I do obviously have full access to the file system directly on the drive and also in the VHD itself.

  Read the article

< Previous Page | 555 556 557 558 559 560 561 562 563 564 565 566  | Next Page >