Search Results

Search found 25013 results on 1001 pages for 'reset the controls within'.

Page 559/1001 | < Previous Page | 555 556 557 558 559 560 561 562 563 564 565 566  | Next Page >

• Hyper-v on 2012R2 startup gen1 vm causes the host to freeze up

  - by sputnik

  I've searched a lot to resolve the following issue, but nothing helped me. My problem is, that starting up a first-gen vm locks up the whole host. Only a hard reset helps. Second-gen vm starts and runs perfectly. The freezes happened on 3 different vms. FreeBSD, Ubuntu, Windows Server 2008R2, while Windows 8.1 on second gen config works perfectly. Im using this pc mainly as a workstation. No eventlog errors nor dumps are generated. My system: Windows Server 2012R2 FX-8350, non OC ASRock 870 Extreme R2 (Crappy board imho) 32GB DDR3 1866@1600 (My motherboard, against the "support" for 1866ram won't work with full speed) 120GB SSD 4.5TB Storage space device I dont think that its due to my system, because vmware workstation was running without problems. Did I forget to configure something? Any help is appreciated. P.S: Even deactivating C1E, C6, C&Q didnt work. P.P.S: With no virtual network adapter set, the system still locks up. Creating a first gen vm without any hdds and network and launching works. Attaching a boot dvd causes the host to freeze. The host freezes as the gen1 vm begins to boot, doesn't matter if from dvd or hdd

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• SATA Driver for Acer Aspire One D257

  - by Robert Niestroj

  i have a Acer Aspire One D257. In this netbook the hard disk is defect so i bought a new one. Now i want to reinstall Windows 7. Im using an external DVD Drive plugged into USB. The Windows 7 DVD is staring, Win7 setup is starting and when it comes to Hard Drive options it says that no drive was detected and i should try search for drivers. It shows me this window: Screenshot from web Now i cant find the right drivers for this netbook to continue with the installation. The laptop has the newest BIOS - 1.15, it is reset to factory default settings except that i enabled the Boot Menu prompt with F12. From the Acer Support Website i've downloaded the SATA AHCI Driver and the Chipset Driver. I unpacked both to a USB flashdrive in seperate folders. When i select the SATA AHCI Driver it does not find any drivers. When i uncheck the checkbox "Hide drivers that are not compatible with hardware on this computer" it shows one driver: Acer HWID (path_to\1.inf). When i continue with this driver i got an error message that says something like: No new devices found. Check if the driver files are on the installation disk. When i show him the Chipset Driver it sees a lot more driver. When i uncheck the checkbox "Hide drivers that are not compatible with hardware on this computer" it show some drivers: Intel N10 Family DMI Bridge Intel N10/ICH7 Family PCI Express Root Port Intel N10/ICH7 SMBUS Controller Intel N10/ICH7 Family USB Universal Host Controller Intel N10/ICH7 Family USB2 Enhanced Host Controller Intel N10/ICH7 Family Interface LPC Controller When i uncheck this checkbox i get a lot more drivers, and some SATA Drivers but the also do not work. I get the same error message as before. Can someone help me find a driver that should work or am i doing anything else wrong?

  Read the article

• Domain Controller died, now get authentication boxes in IE for SDL Tridion 2009

  - by Rob Stevenson-Leggett

  We had a major network issue where our secondary domain controller (responsible for Win2k3 boxes) died and had to be rebuilt (I beleive this is what happened, I am a developer not network admin). Anyway, I am working remotely via VPN at the moment and since this happened, I am getting an authentication box when trying to access certain areas of SDL Tridion via IE (Tridion 2009 SP1 is IE only) it seems like somewhere my credentials are not being passed correctly or the ones cached on my laptop do not match the ones the Domain Controller has. This only seems to affect Windows 2003 servers. Our IT support thinks that the only way to sort it out is to connect my laptop directly to the network. I am not planned to go to the office for a few weeks at least and this issue means I have to work with Tridion via Remote Desktop. We thought changing the password on my account might work but this didn't help. So basically my question is, is there any way I can reset my credential cache without having to reconnect to the network? Or is it IE that is causing the problem perhaps, since I can RDP to servers and use Tridion 2011 instances in other browsers fine? I am on Windows 7 using SonicWall VPN client.

  Read the article

• Setting up self signed cert and CA [plesk / linux]

  - by microchasm

  I'm about ready to give up and do a clean wipe of this machine and start over with ISPConfig or some other variant. I installed Plesk on this machine to help with some of the handiwork. It is the free version (single domain); I don't need it for much. It's nice, though, to use to set up db's email, etc. Anyway, I would like to set it up as a CA (which I can add to users' trusted root servers to alleviate those warnings). It seems like Plesk does all it can to obfuscate where things are. Despite trying to find the conf files, and crt/pem/key etc. I am (5 hours later) now left with a machine that won't even get to the ssl page. The browser will sit there, until a 'connection reset' error comes up. In error_log, I get messages saying CN doesn't match server name -- which it does. ssl_error_log: [Thu May 13 16:02:14 2010] [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) [Thu May 13 16:12:19 2010] [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) not very helpful. If anyone has any experience, and/or recommendations (including other software), I'd be much obliged. NB RHEL5; 1 domain, 3 subdomains; everything local only. Thanks.

  Read the article

• Use Apache authentication + authorization to control access to Subversion subdirectories

  - by Stefan Lasiewski

  I have a single SVN repo at /var/svn/ with a few subdirectories. Staff must be able to access the top-level directory and all subdirectories within it, but I want to restrict access to subdirectories using alternate htpasswd files. This works for our Staff. <Location /> DAV svn SVNParentPath /var/svn AuthType Basic AuthBasicProvider ldap # mod_authnz_ldap AuthzLDAPAuthoritative off AuthLDAPURL "ldap.example.org:636/ou=people,ou=Unit,ou=Host,o=ldapsvc,dc=example,dc=org?uid?sub?(objectClass=PosixAccount)" AuthLDAPGroupAttribute memberUid AuthLDAPGroupAttributeIsDN off Require ldap-group cn=staff,ou=PosixGroup,ou=Unit,ou=Host,o=ldapsvc,dc=example,dc=org </Location> Now, I am trying to restrict access to a subdirectory with a separate htpasswd file, like this: <Location /customerA> DAV svn SVNParentPath /var/svn # mod_authn_file AuthType Basic AuthBasicProvider file AuthUserFile /usr/local/etc/apache22/htpasswd.customerA Require user customerA </Location> I can use Firefox and curl to browse to this folder fine: curl https://svn.example.org/customerA/ --user customerA:password But I cannot use check out this SVN repository: $ svn co https://svn.example.org/customerA/ svn: Repository moved permanently to 'https://svn.example.org/customerA/'; please relocate And on the server logs, I get this strange error: # httpd-access.log 192.168.19.13 - - [03/May/2010:16:40:00 -0700] "OPTIONS /customerA HTTP/1.1" 401 401 192.168.19.13 - customerA [03/May/2010:16:40:00 -0700] "OPTIONS /customerA HTTP/1.1" 301 244 # httpd-error.log [Mon May 03 16:40:00 2010] [error] [client 192.168.19.13] Could not fetch resource information. [301, #0] [Mon May 03 16:40:00 2010] [error] [client 192.168.19.13] Requests for a collection must have a trailing slash on the URI. [301, #0] My question: Can I restrict access to Subversion subdirectories using Apache access controls? DocumentRoot is commented out, so it's not clear that the FAQ at http://subversion.apache.org/faq.html#http-301-error applies.

  Read the article

• Moving a lotus database causes incoming mail failure

  - by Logman

  Hey all, I moved a couple lotus note databases to another hd (ran out of space) by using a directory link/pointer on the domino server. USed a text file with the .DIR ext with the desired new path etc... well that works fine. I open up a lotus notes client, use the id and then OPEN the database. The directory link works fine, the new location of the db is opened with no problems. We found out that we couldnt FORWARD any mail: We did the following to make it work: Goto menu FILE|MOBILE|EDIT CURRENT LOCATION Goto tab MAIL and enter the correct path for "Mail File:" example: it should read "mail\morespace\flabor" and not "mail\flabor" "morespace" = directory link/pointer we can forward and reply to emails fine after that fix. The problem is that the user has no incoming email. Domino is still trying to send the incoming mail of that user to its old db location "mail\flabor" instead of "mail\morespace\flabor". Delivery error saying user does not exist. Is this a cache problem? We have reset the server ("Q" at the prompt), though we have not completely shut it down though. Thanks Frank

  Read the article

• Replacing compiz/metacity with openbox reduces workspaces to 1

  - by Brian

  I like to use the GNOME desktop, but I prefer to replace its window manager with openbox, with 4 workspaces. However, when I run openbox --replace, the number of workspaces available drops to 1. If I go into obconf, workspaces is still configured to be 4 (~/.config/openbox/rc.xml shows the same). I can get the workspaces to reappear by changing the value in obconf to anything else, and then back to 4. I have just been dealing with this problem since Ubuntu 9.04 (now up to 10.10) since I don't reboot very often. But it's really annoying to have to reset my workspaces whenever I do have to reboot. Changing the value in rc.xml and running openbox --reconfigure does not seem to have any effect. So what is obconf doing that I'm not (sends a dbus message perhaps [EDIT: watching with dbus-monitor I see no messages when changing the workspaces value in obconf])? I was hoping there would be a cleaner way to change the window manager than just running openbox --replace at login. So my questions are: Is there a better way to specify an alternate window manager (i.e. a way that doesn't cause the workspaces to break)? If not, how can I automatically set the number of workspaces back to 4? Update: I finally got around to trying what I commented on MrShunz's answer (adding WINDOW_MANAGER=/usr/bin/openbox to ~/.gnomerc). But the effect is the same as openbox --replace.

  Read the article

• Setting up port forwarding for web server

  - by reyjavikvi

  This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

  Read the article

• Why would my wireless cut in and out every minute or so?

  - by Strilanc

  I've been having problems with my wireless. I moved to a new apartment, and the wireless seems incredibly unreliable. Sometimes it will be stable for hours until, all of a sudden, it starts cutting in and out. I'll get 30-90 seconds of normal behavior, then 5-30 seconds of nothing, then repeat. Sometimes the connection will stop working entirely, until I power-cycle the router. It is extremely, extremely annoying. Surfing the web isn't too bad, assuming you can stand the random 5-30 second waits. But some connections are sensitive enough to timeout, and it certainly makes multiplayer games unplayable. Facts: I confirmed the problem using ping google.com -t. I get normal traffic, interspersed with bursts of "Request timed out.". I've never had this problem before with this laptop. I didn't bring my own router or modem to the apartment. I'm using what the old tenant had. Hooking directly to the modem via an ethernet cable results in a stable connection. Temporarily cutting power to the router sometimes fixes the problem. Sometimes it doesn't. I reset the router, but the problem remained. Apparently the previous tenant had issues with the internet, but I don't know what they were specifically. The router is a D-Link DIR-615, and their tech support is useless.

  Read the article

• Windows Photo Viewer can't open this picture because you don't have the correct permissions to access the file location

  - by Software Monkey

  My system in Windows 7 and fully up to date with all patches and options (except for Microsoft Silverlight, which I refuse to install). I get this error whenever I try to open an image using Windows Photo Viewer, such as when previewing from Explorer or when opening an image attachment to an email. I have already verified correct permissions to the file and all folders in the path. The strange thing is that every other program I have seems to open the images fine, including "Slideshow" from Windows Explorer. Even more strange, in WPV there is an "Open" menu that lists the other programs for images including GIMP and MS Paint and they open the very file that WPV is complaining about just fine. That should eliminate permissions as being the problem, especially since (logically at least) they are read/write while WPV is read-only. I have even edited and saved the images that WPV does not open. I am out of ideas, and searching for answer on the Web has resulted only in the same tired repitition of some flavor of "take ownership and reset permissions for the entire drive", which I have already done. And which is counter-indicated by the fact that only Windows Photo Viewer seems to have a problem. The one thing which is slightly unusual is that for normal files they are all on a second HDD mounted into C:, however for email attachments the temporary folder is C:\Temp\, which is directly on that drive.

  Read the article

• VMWare steals IP addresses

  - by Ishan Amin

  I'm having a peculiar problem, that I think I have narrowed down to VMware. For the past one year, every once in a while we lose internet connection and not all users (about 10 users) go down at the same time, its usually one-by-one. First someone will call me and say "Internet is down" and then we would go reset the router and modem and switch and it would be working again for a while, then go down again without any pattern or replicatable sequence. We'd go repeat the steps again to get everyone in the office running again. We called our Internet Service Provider and they constantly say, We see your modem and we see your router and from thier end everything is OK. we replaced our router and switch and modem, twice! Last friday, it dawned upon me, that everytime we turn on a VMware machine, this sequence of taking everyone down starts, which also explains the message that my users get for "IP Conflict Found" So we do alot of VMware testing and lo and behold, it takes my Internet down. My Yahoo and Gtalk would continue working but www is down when the VMware machines are started. I do use bridged networking to all the VMware machines, but I dont know what else to set it at. now, sorry for this long rambling but anyone have any clue on how to stop this? thanks IA

  Read the article

• How to figure out what VirtualBox did?

  - by AndrejaKo

  I'm trying to boot a custom made-in-ASM OS on my recent laptop. The OS is intended to be installed on a floppy and during make creates a bootable floppy. Since I don't have a floppy drive, I installed it on a virtual floppy. After that I used WinToFlash's create bootable MS-DOS USB drive option to transfer the floppy image to an USB flash drive. Then I tried to boot my computer from it but got only a repeating broken string on screen. After all that I made a virtual hard disk image form the flash drive using this tutorial and tried to boot a virtual machine from it. First time I got same problem as on real computer. I then used the reset option and next time and every time after that OS booted correctly. My question is: How do I figure out what exactly happened to the virtual machine between first and second boot? UPDATE I just created a new VM with default settings for windows XP and it has the same problem that I have on a real computer. I was unable to reproduce the procedure which made the first VM work correctly.

  Read the article

• iptables captive portal remove user

  - by Burgos

  I followed this guide: http://aryo.info/labs/captive-portal-using-php-and-iptables.html I am implementing captive portal using iptables. I've setup web server and iptables on linux router, and everything is working as it should. I can allow user to access internet with sudo iptables -I internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN and I can remove access with sudo iptables -D internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN However, on removal, user can still open last viewed page as many times he wants (if he restart his Ethernet adapter, future connections will be closed). On blog page I found a script /usr/sbin/conntrack -L \ |grep $1 \ |grep ESTAB \ |grep 'dport=80' \ |awk \ "{ system(\"conntrack -D --orig-src $1 --orig-dst \" \ substr(\$6,5) \" -p tcp --orig-port-src \" substr(\$7,7) \" \ --orig-port-dst 80\"); }" Which should remove their "redirection" connection track, as it is written, but when I execute that script, nothing happens - user still have access to that page. When I execute /usr/sbin/conntrack -L | grep USER_IP after executing script I am having nothing returned, so my questions: Is there anything else that can help me clean these track? Obviously - I can't reset nor mine, nor users network adapter.

  Read the article

• How do I keep the keyword.url setting in firefox to default when you restart the browser without del

  - by user34801

  I am on the latest version of Firefox (not beta or anything like that) and currently my keyword.url is stuck on search.google.com (which I don't remember setting even though the about:config says it's a user setting. Can someone tell me how to set it back to default and keep it at default when I reset my browser? I do not want to delete prefs.js as I do not want to go thru setting up all the extension settings I have just to have my location bar search google (if this is the only way then I'll stick with searching from the search bar instead). I've checked all my extensions that may effect the location bar but could not find anything that says it would change the default search engine for this. I've also tried to open the prefs.js in wordpad or notepad but it just ends up freezing when trying to edit it at all (yes the browser is closed at the time). I also deleted the prefs-1.js (along with 2 others) that were older (after trying to rename those to prefs.js and see if this corrects it. It might have but had such old extension settings I went back to my latest prefs.js with this one issue instead of the issue of setting back up a ton of extensions. I can give any other info if needed, someone please help me fix this issue if possible.

  Read the article

• MySQL partition "full"?

  - by gdea73

  I have a server that runs Debian 6.2, with Apache, PHP5, and MySQL. Well, I hadn't done anything with MySQL at all so far, just Apache and PHP; I must have installed it (mysql-server) at some point along the line, and I decided to login to the database for the first time a couple days ago as I was considering using the database for a future website project. I noticed that the "root" user had a password, and I didn't recall having set one. My usual root password was incorrect. So I attempted to reset the password. sudo service mysql stop (stopped successfully) sudo /usr/bin/mysqld_safe --skip-grant-tables --skip-networking & started successfully, from what I can tell. However, mysql itself returns "Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld,sock' (2)", and additionally sudo service mysql start returns "/etc/init.d/mysql: ERROR: The partition with /var/lib/mysql is too full! ... failed!" df -h tells me that / is 26% used, a 20GB partition, and /home, roughly 900GB, has only 5% usage. On a potentially related note, I've been experiencing random hangs since I noticed this problem, my tty2 randomly froze several times while idle, and the entire system is suddenly unstable. gnome-terminal also does not open. (Gnome-terminal apparently works now, disregard that part, but the server is still being somewhat unstable, I randomly lost connection when I was SSHed into it from my laptop, twice now.)

  Read the article

• How do I install a different OS on a Compaq Presario cq56 with preinstalled SuSE 11?

  - by McCoy

  Thing is, I don't have a clue of Linux systems, I usually use WinXP. Bought a notebook with SuSE 11 on it, because I have my XP licence and thought I could install that if I found the chipset drivers for the hardware (which I'm not completely sure I have the right versions of). Then I thought I'd give it a shot with the SuSE, looked nice enough. But I can't get my external hd to work (tried force mount) and the banshee doesn't do anything like playing video. Since that is one of the two main purposes of this notebook, I need to get that to work. Tried downloading VLC player, but that only works with SuSE 11.1 upwards. So I downloaded a SuSE 11.3 and burned the iso. But surprise, no way the notebook would boot from cd. Same with the XP cd (considered setting up a dual boot). And no, I can't get to BIOS to reset to default, either. So I can basically do nothing else than going online with this thing and that's not enough for me (gamer in withdrawal, yikes!). I need at least to get to my firefox profile on the external hd and be able to watch video. Can somebody please help me? I think at this point I'd prefer to install XP and MAYBE the SuSE 11.3 after that. I'm not a native speaker, so please speak plainly, thanks. :) Edit: if this is impossible, could someone please help me with the external hd mount and video playback? Edit: Found out how to boot from cd by now. But still no XP, because I get bluescreen after bluescreen while setup is loading files. I guess it's the missing SATA drivers...

  Read the article

• MySQL Master - Master Broken

  - by Recc

  I've Inherited a Mysql master master system, I've noticed the second master (lets call it slave from now on as it's running on a 'slave' machine) stopped getting its db's updated. I saw that Master: Slave_IO_Running: Yes Slave_SQL_Running: Yes Slave: (with an error I truncated) Slave_IO_Running: Yes Slave_SQL_Running: No Last_Errno: 1062 Last_Error: Error 'Duplicate entry '3' for key 'PRIMARY'' on [...] I don't know what caused it to process considering we cant get duplicate there. What's important is to resume normal operations; Right now I've stop slave; on the Master and stop slave; on the Slave because I saw that if I change records on the Slave the changes Do Get Propagated to Master which is in active use. How do I: Force sync EVERYTHING from master to slave without affecting data on master? Then hopefully have slave pickup replication as usual? UPDATE OK I Tried deleting all tables on slave then it complained in that error section that the 'table' doesnt exist. So i made a no data dump of Master, and made sure I have only empty tables in Secondary (slave). I start slave; on slave BUT now it's complaining about bloody alter table statements for instance: Last_Errno: 1060 Last_Error: Error 'Duplicate column name [...] Query: 'ALTER TABLE [...] How to skip the fracking alter statements I just want to replicate the bloody data and be done with it, my tables have the lates changes already FFS and now its complaining about changes made after the replication seized weeks ago How do I reset the log or something? OUTSTANDING Why would this start happening? The "Secondary" is propagating to "Primary". "Primary" is not propagating to "Secondary". But any fixes I tried to do left it in the same state Yes-Yes Yes-No with same Last_Error. I think around that time the server was taken off the network, could that confuse MySQL in some way?

  Read the article

• Postfix misconfigured? 550 Sender rejected from recieving server

  - by wnstnsmth

  We use Postfix on our CentOS 6 machine, having the following configuration. We use PHP's mail() function to send rudimentary password reset emails, but there is a problem. As you will see, mydomain and myhostname is correctly set, afaik. alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 html_directory = no inet_interfaces = localhost inet_protocols = all mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost mydomain = ***.ch myhostname = test.***.ch newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop unknown_local_recipient_reject_code = 550 Now this is the stuff that is in the /var/log/maillog of Postfix upon sending an email to ***.***@***.ch, with ***.ch being the same domain our sending server test.***.ch is on: Dec 13 16:55:06 R12X0210 postfix/pickup[6831]: E6D6311406AB: uid=48 from=<apache> Dec 13 16:55:06 R12X0210 postfix/cleanup[6839]: E6D6311406AB: message-id=<20121213155506.E6D6311406AB@test.***.ch> Dec 13 16:55:07 R12X0210 postfix/qmgr[6832]: E6D6311406AB: from=<apache@test.***.ch>, size=1276, nrcpt=1 (queue active) Dec 13 16:55:52 R12X0210 postfix/smtp[6841]: E6D6311406AB: to=<***.***@***.ch>, relay=mail.***.ch[**.**.249.3]:25, delay=46, delays=0.18/0/21/24, dsn=5.0.0, status=bounced (host mail.***.ch[**.**.249.3] said: 550 Sender Rejected (in reply to RCPT TO command)) Dec 13 16:55:52 R12X0210 postfix/cleanup[6839]: 8562C11406AC: message-id=<20121213155552.8562C11406AC@test.***.ch> Dec 13 16:55:52 R12X0210 postfix/bounce[6848]: E6D6311406AB: sender non-delivery notification: 8562C11406AC Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: 8562C11406AC: from=<>, size=3065, nrcpt=1 (queue active) Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: E6D6311406AB: removed Dec 13 16:55:52 R12X0210 postfix/local[6850]: 8562C11406AC: to=<root@test.***.ch>, orig_to=<apache@test.***.ch>, relay=local, delay=0.13, delays=0.07/0/0/0.05, dsn=2.0.0, status=sent (delivered to mailbox) Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: 8562C11406AC: removed So the receiving server rejects the sender (line 4 of log output). We have tested it with one other recipient and it worked, so this problem might be completely unrelated to our settings, but related to the recipient. Still, with this question, I want to make sure we're not making an obvious misconfiguration on our side.

  Read the article

• AGP 4x slot running at 2x

  - by Wesley

  Hi all, Here are the specs of the machine related to this question: AMD Athlon XP 2400+ @ 2 GHz / 2x 512MB PC3200 DDR RAM / 3D Fuzion 128MB GeForce 6200 AGP / WD 160GB IDE HDD / FIC AM37 (mobo) / Codegen 350W PSU / Windows XP Pro SP3 So, for some odd reason, the GeForce 6200 that is in the AGP 4x slot is not running at 4x, but 2x. The card itself supports AGP 4x and even 8x. When I enter the BIOS, the options for the AGP slot only allow 2x as the max. Before, the max option for the AGP slot in the BIOS was 4x. (I do get the 4x option after I reset CMOS, but it does not stick after a restart.) I don't exactly know what the problem could be, but a few weeks ago, this machine's hard drive was reformatted and got a fresh install of XP. Also, I did install Rivatuner, but I never overclocked it at all. (I uninstalled it after thinking that it had done something.) Otherwise, I cannot figure out the cause of the problem. Does anybody have an idea why this is happening? (Would I have to do another reformat?) Thanks in advance. PS: the other options for the AGP slot are aperture size (which I tried changing, but it did nothing) and FastWrite (enabled by default).

  Read the article

• Router not connecting to the internet

  - by Peter

  I had a weird problem this morning with my router - it's an Alice Gate VoIP 2 Plus WI-FI - not connecting to the internet after more or less 1 hour online (I'm always connected with the ethernet cable). The led status lights for Power, WI-FI, ADSL, Internet, Service should be on in order to be connected and navigate online. The problem was that the leds ADSL, Internet were off and I did not know why because it never happened before. I looked at the stats in the settings and the numbers for Bytes/Packages for both Sent/Received were there and increasing but I couldn't connect to the internet. I called tech support, they checked and told me to keep the router on for 48 hours because they were checking it. I've reset it twice before and after I called tech support and it still did not work so after about 2 hours of waiting I tried connecting using WI-FI and the leds 'magically' turned on, first the ADSL and Internet(Internet led always turns on last). At this point I'm curious what could of caused this and I'm doubting that the tech-support guys did something. What could of been the problem with the ethernet cable not connecting in the first place? It always works. What do the tech support guys normally do when they tell me to keep the router on so they can 'check it'? PS: I'm using ubuntu 32 bit

  Read the article

• Extremely high mysqld CPU usage with no active queries

  - by RadarNyan

  I have a VPS running Ubuntu 12.04 LTS with LEMP stack, followed the guide from Linode Library (since I'm using a Linode) to setup, and everything worked fine until now. I don't know what's wrong, but my CPU usage just goes up since a week ago. Today things getting really bad - I got 74% CPU usage so I went check and found that mysqld taking too much CPU usage (somewhere around 30% ~ 80%) So I did some Google Search, tried disable InnoDB, restart mysql, reset ntp / system clock (Isn't this bug supposed to happen more than a year ago?!) and reboot my VPS, nothing helped. Even with mysql processlist empty, I still get mysqld CPU usage very high. I don't know what I missed and have totally no idea, any advice would be appreciated. Thanks in advance. Update: I got these from running "strace mysqld" write(2, "InnoDB: Unable to lock ./ibdata1"..., 44) = 44 write(2, "InnoDB: Check that you do not al"..., 115) = 115 select(0, NULL, NULL, NULL, {1, 0}^[[A^[[A) = 0 (Timeout) fcntl64(3, F_SETLK64, {type=F_WRLCK, whence=SEEK_SET, start=0, len=0}, 0xbfa496f8) = -1 EAGAIN (Resource temporarily unavailable) hum... I did tried to disable InnoDB and it didn't fix this problem. Any idea? Update2: # ps -e | grep mysqld 13099 ? 00:00:20 mysqld then use "strace -p 13099", the following lines appears repeatedly: fcntl64(12, F_GETFL) = 0x2 (flags O_RDWR) fcntl64(12, F_SETFL, O_RDWR|O_NONBLOCK) = 0 accept(12, {sa_family=AF_FILE, NULL}, [2]) = 14 fcntl64(12, F_SETFL, O_RDWR) = 0 getsockname(14, {sa_family=AF_FILE, path="/var/run/mysqld/mysqld.sock"}, [30]) = 0 fcntl64(14, F_SETFL, O_RDONLY) = 0 fcntl64(14, F_GETFL) = 0x2 (flags O_RDWR) setsockopt(14, SOL_SOCKET, SO_RCVTIMEO, "\36\0\0\0\0\0\0\0", 8) = 0 setsockopt(14, SOL_SOCKET, SO_SNDTIMEO, "<\0\0\0\0\0\0\0", 8) = 0 fcntl64(14, F_SETFL, O_RDWR|O_NONBLOCK) = 0 setsockopt(14, SOL_IP, IP_TOS, [8], 4) = -1 EOPNOTSUPP (Operation not supported) futex(0xb786a584, FUTEX_WAKE_OP_PRIVATE, 1, 1, 0xb786a580, {FUTEX_OP_SET, 0, FUTEX_OP_CMP_GT, 1}) = 1 futex(0xb7869998, FUTEX_WAKE_PRIVATE, 1) = 1 poll([{fd=10, events=POLLIN}, {fd=12, events=POLLIN}], 2, -1) = 1 ([{fd=12, revents=POLLIN}]) er... now I totally don't get it x_x help

  Read the article

• How to use AND/OR Building Block content in a Word 2007 template

  - by JimmyJames

  I am creating a Schedule of Work template and am successfully using Developer Tab and Quick Parts to allow user to choose content on an "either/or" basis: either A; OR B; OR C; etc., essentially choose one option from many. One Building Block control, one paragraph, nice and clean. Now what I need to do but cannot seem to figure out, is how to allow user to choose content on an "and/or" basis: either A AND B; A OR B AND C; B AND D AND E OR F; etc., essentially choose several options from many on a variable basis. One Building Block control, maybe one paragraph, maybe three or more paragraphs. Not so clean. I thought of building choice options for all possible paragraph combinations, but I can have as many as 7 or 8 different paragraphs, and that solution quickly becomes unworkable. Multiple controls--some of which will be left unused doesn't work either, since I cannot find an easy way to have a "Choose or Delete" control that actually deletes if "Delete" is chosen. Recommendations are most welcome.

  Read the article

• pxe boot dos 7.x / 8.x on modern mainboard without floppy controller

  - by GitaarLAB

  How to pxe boot MS DOS 7.x / 8.x on a modern pc (mainboard without floppy controller) without using an external usb floppy drive? MS DOS 6.22 and earlier or other flavors pxe boot just fine on floppy-less hardware. But DOS 7.x and 8.x renders an error on boot: "Type the name of the Command Interpreter (e.g., C:\WINDOWS\COMMAND.COM) I read somewhere during research this was a rather unknown error, that started to become more common due to the advent of floppy-controller-less hardware. On some hardware (bios dependent) one could plug a usb-floppy-drive in the computer before booting (but that MIGHT also require it to be a "golden floppy drive" (as they where called back then). From a russian site (I read about a year ago and cannot find the hyperlink) MS-Dos versions 6.22 did some-kind of floppy-drive reset during initialization and since it couldn't connect to the floppy-host thus the error. How can I resolve this (without a physical external usb floppy)? Might there be some kind of virtual floppy-driver that could resolve this (for example to be loaded before the dos image loads)? Or could someone point me into the right direction (maybe even a hex-address and some further explanation or something)? I'm using syslinux by the way.

  Read the article

< Previous Page | 555 556 557 558 559 560 561 562 563 564 565 566  | Next Page >