Search Results

Search found 7940 results on 318 pages for 'intel wireless'.

Page 56/318 | < Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63  | Next Page >

• Need help with chronic slow wifi connections

  - by mgeorge

  I have had chronic slow wifi connections on several networks for a while now, I think since my update to 12.04 when it came out. I have tried many of the tips and tricks already available out there in the forums with no luck (wicd, etc..). I want to see if any of you experts out there might be able to help me, and thanks in advance!! I use ubuntu 12.04 on a lenovo ideapad y650, and most networks I connect to lose the connection frequently or do not give appropriate bandwidth when I am connected. Here are some results of the usual go-to system checks: cat /etc/lsb-release; uname -a: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Linux mgeorge-lenovo 3.2.0-48-generic-pae #74-Ubuntu SMP Thu Jun 6 20:05:01 UTC 2013 i686 i686 i386 GNU/Linux lspci -nnk | grep -iA2 net: 04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlwifi -- 08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) Subsystem: Lenovo Device [17aa:3878] Kernel driver in use: tg3 lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 090c:7371 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) iwconfig: lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Dyno" Mode:Managed Frequency:2.412 GHz Access Point: CC:5D:4E:46:0A:93 Bit Rate=150 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-40 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:948 Invalid misc:728 Missed beacon:0 eth0 no wireless extensions. rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod: Module Size Used by uvcvideo 67203 0 videodev 86588 1 uvcvideo nouveau 712674 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197641 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau mxm_wmi 12893 1 nouveau wmi 18744 1 mxm_wmi joydev 17393 0 arc4 12473 2 snd_hda_codec_realtek 174313 1 snd_hda_codec_hdmi 31775 1 snd_hda_intel 32719 3 snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80916 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi psmouse 86520 0 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event serio_raw 13027 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq iwlwifi 366509 0 mac80211 436493 1 iwlwifi snd 62218 16 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,sn d_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 17890 0 sparse_keymap 13658 1 ideapad_laptop cfg80211 178877 2 iwlwifi,mac80211 ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 ir_rc5_decoder 12459 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 video 19115 1 nouveau ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir bnep 17830 2 rfcomm 38139 0 parport_pc 32114 0 bluetooth 158479 10 bnep,rfcomm ppdev 12849 0 binfmt_misc 17292 1 mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141414 0 nm-tool: NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: tg3 State: unavailable Default: no HW Address: 00:23:5A:CC:85:BD Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 [Dyno] -------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: yes HW Address: 00:22:FA:D0:94:CA Capabilities: Speed: 150 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) *Dyno: Infra, CC:5D:4E:46:0A:93, Freq 2412 MHz, Rate 54 Mb/s, Strength 81 WPA2 IPv4 Settings: Address: 10.0.0.43 Prefix: 24 (255.255.255.0) Gateway: 10.0.0.1 DNS: 10.0.0.1

  Read the article

• Will Apple abandon OpenCL?

  - by John

  I am developing OpenCL applications, amongst others for MacOS. The new Macbook pro 13 inch comes with an Intel HD Graphics 3000 card so it seams reasonable to assume all their mainstream computers like Macbook and Mac mini will also come out with this Intel graphics card soon. OpenCL is not available for Intel graphics cards. Intel having a terrible reputation in developing graphics drivers and Apple knowing this makes me wonder Apple is abandoning OpenCL already again. Especially considering OpenCL should run anywhere, not only on high end systems. Developing applications only for the high end Macs with dedicated graphics hardware or for previous generation hardware with the Geforce 320M would not be a feasible option for me. Does anybody have any thoughts on this?

  Read the article

• Trouble with 12.10 lag

  - by Brennan

  Well basicly lately I have been having lag problems with 12.10. I will post my specs, but before the update to 12.10, it said that I had intel graphics. Now it says I have Gallium. My specs: *Memory: 3.9 GiB *Processor: Pentium(R) Dual-Core CPU E5500 @ 2.80GHz × 2 *Graphics: Gallium 0.4 on llvmpipe (LLVM 3.2, 128 bits) (used to say intel graphics) *OS Type: 32-bit *Disk: 486.1 GB The output of the command sudo apt-cache check is this: E: Invalid operation check The output of the command sudo lspci -nnk | grep -A5 VGA is this: 00:02.0 VGA compatible controller [0300]: Intel Corporation 4 Series Chipset Integrated Graphics Controller [8086:2e32] (rev 03) Subsystem: ASUSTeK Computer Inc. Device [1043:836d] Kernel driver in use: i915 00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 01) Subsystem: ASUSTeK Computer Inc. Device [1043:8445] Kernel driver in use: snd_hda_intel

  Read the article

• sony vaio WLAN problem using 12.04

  - by Fredrik

  I'm unable to get my WLAN to work for my Sony Vaio model VPCF23C5E No problem connecting from windows, smartphones etc. $ sudo lshw -C network; lsb_release -a; uname -a; sudo rfkill list; dmesg | grep -i firm *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 64:27:37:92:99:0f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-29-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:f7000000-f707ffff memory:f7080000-f708ffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 06 serial: f0:bf:97:dd:b2:bd size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-1.fw ip=192.168.1.4 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:50 ioport:9000(size=256) memory:e2104000-e2104fff memory:e2100000-e2103fff LSB Version: core-2.0-amd64:core-2.0-noarch:core-3.0-amd64:core-3.0-noarch:core-3.1-amd64:core-3.1-noarch:core-3.2-amd64:core-3.2-noarch:core-4.0-amd64:core-4.0-noarch Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise Linux siriedit 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no [ 1.287449] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 18.273582] [Firmware Bug]: ACPI(NGFX) defines _DOD but not _DOS Seen some proposed solution e.g. Wireless network cannot be enabled for Sony VAIO E series but answers there don't solve my problem... I'm out of ideas :-( What else can I check? update $ ifconfig -a eth0 Link encap:Ethernet HWaddr f0:bf:97:dd:b2:bd inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f2bf:97ff:fedd:b2bd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5072 errors:0 dropped:0 overruns:0 frame:0 TX packets:4444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4568435 (4.5 MB) TX bytes:610624 (610.6 KB) Interrupt:50 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1498 errors:0 dropped:0 overruns:0 frame:0 TX packets:1498 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:114156 (114.1 KB) TX bytes:114156 (114.1 KB) wlan0 Link encap:Ethernet HWaddr 64:27:37:92:99:0f inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6627:37ff:fe92:990f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1277 errors:0 dropped:0 overruns:0 frame:0 TX packets:472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:483155 (483.1 KB) TX bytes:61031 (61.0 KB)

  Read the article

• Broadcom bcm4313 Ubuntu 13.10 connection time out

  - by Wahtever

  After upgrading to Ubuntu 13.10 I keep getting connection timed out every few seconds at which point i have to disconnect and reconnect to the WiFi network. The WiFi card worked fine on 13.04 with the bcmwl-kernel-source installed but giving problems on 13.10: *-network description: Wireless interface product: BCM4313 802.11bgn Wireless Network Adapter vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: c0:14:3d:cc:c9:c7 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.4 latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f0500000-f0503fff How can i fix this? Thanks

  Read the article

• No Internet Connection - ubuntu 11.10

  - by emersonhsieh

  I installed Ubuntu 11.10 recently. After the first bootup the computer freezes so I have to force-quit my computer. Then I turned on my computer after that. I tried connecting to the internet. My (and my neighbor's) wireless networks shown up, but no matter how many times I tried, I can't connect to my home network. I checked the password and the other laptop's internet works (a MacBookPro). It was a wireless network. What's weird is that the Wireless network worked when I was installing ubuntu How can I connect to the internet now? I don't have a wired network. Please Help! Any help will be appreciated Specs: ASUS F81Se, Windows 7 Dual-boot, I remember the wireless card was made by Atheros, 4GB RAM

  Read the article

• Switching from Debug into Release Mode with VS2010 as IDE and Intel C++ Compiler 13

  - by Drazick

  I have a code of a Plug In from an SDK. The code is in Debug Mode. I use Intel Compiler which only applies optimizations in Release Mode. Under configuration manager of the project only "Debug" mode is defined. How could I switch to "Release" mode and enable all Intel Compiler's optimizations? If I enable them on debug mode nothing is applied (Empty Report). I couldn't find the trick to do so. Thank You.

  Read the article

• Audio output and input stopped working after the last update

  - by renatov

  I'm using Ubuntu 14.04 and everything was perfect until todays's update. Now my audio output (speakers) and input (microphone) stopped working. I guess it's a driver issue, but I need help to debug this problem and to solve it. I have a Dell Inspiron 5421 notebook with an Intel audio integrated sound card: $ lspci | grep Audio 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04) If I go to Ubuntu Settings Sound Output, it doesn't show my Intel card there anymore: The same for the Input tab, it doesn's show my Intel card there anymore: Could you please help me?

  Read the article

• Sony VAIO wireless card not connecting intel 4965AGN

  - by marcski55

  I'm running a Sony VAIO VGN-CR410E, and recently moved it to Ubuntu from Windows 7. Both my home and work networks (which I maintain) run WPA/WPA2-PSK authentication for security. My wireless network card (intel 4965AGN) will not connect to them unless I am in the same room (kind of defeats the purpose of wireless). The PC is 4 years old and the routers are brand new (last month or so). Had no problems with it with Win7, but Ubuntu just doesn't like the networks. As an IT manager, my laptop needs to work, so any help is appreciated. If this is a duplicate, please let me know of what. I've spent hours searching and nothing has worked. Thanks for your help. (This is my first experience fully relying on Ubuntu). I can see the networks and attempt connection, but it fails authentication. Let me know of any code you need.

  Read the article

• Why doesn't Unity 3D work on my HD3000 integrated graphics?

  - by Zatsugami

  So I got my new laptop recently. HP Envy 15 with switchable graphics card. I'm using both windows and ubuntu, but for ubuntu I need just Intel HD3000 for better battery live. I've installed fglrx-updates and fglrx-amdcccle-updates. The drivers seems to work for my ATI card. The problem is, Intel HD3000 does not support Unity 3D. Why? My older Intel GMA 4500 did this. lspci -nn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0126] (rev 09) 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Whistler [AMD Radeon HD 6600M Series] [1002:6741] (rev ff)

  Read the article

• AMD défie Intel sur le marché des serveurs et sort des puces à 12 coeurs, Intel relativise

  AMD défie Intel sur le marché des serveurs Et sort des puces à 12 c?urs, Intel relativise AMD vient de lancer une nouvelle gamme de puces pour serveurs baptisée Magny-Cours. Ces puces embarquent entre 8 et 12 c?urs et visent clairement à prendre une position dominante sur ce marché professionnel. La gamme se compose des 6 références suivantes : Opteron 6128 : 8 c?urs, 1,5 GHz Opteron 6134 :8 c?urs, 1,7 GHz Opteron 6136 : 8 c?urs, 2,4 GHz Opteron 6168 : 12 c?urs, 1,9 GHz Opteron 6172 :12 c?urs, 2,1 GHz Opteron 6174 : 12 c?urs, 2,2 GHz De son coté...

  Read the article

• Intel Science Talent Search 2010 Winners

  New Mexico Teen Awarded $100,000 New Mexico - United States - Intel Science Talent Search - Government - Business and Economy

  Read the article

• Extended service set help [closed]

  - by Cygnus X

  Sorry, this is going to be long and rambly. So, at home my network is set up as such: I have a "master router" that handles DHCP, from there I have a basic 5 port switch, and coming off that, I have a second router that I put in access point mode so that I could have better wireless coverage in my house. I cant seem to access it through a web browser since the master router kicked in and assigned it an ip address. But, i told you all that story, so that i could tell you this story. At the company I work for, they are trying to set up wireless cameras, according to the manual for these, in order to connect these cameras to our network, we need to get into the wireless router and associate the router with the cameras, but the problem is, the network is setup like my home network. Theres a "master router" which is a windows 2003 server, and then a wireless router in AP mode dishing out wireless access. I cant get into the router (by the way I'm not the system admin for the company, nor do i know jack squat about windows server , nor can I easily get in contact with the system admin. (quite the cluster f*k, eh?)) I've tried using wireshark to find the routers ip, dug through arp tables, tried plugging straight into the router, but I cant seem to get into the damn thing. Any ideas/suggestions would be greatly appreciated.

  Read the article

• Intel Upgrades Atom, Targeting Smartphones

  Intel claims its new Atom offer lower power consumption, tinier size and reduced costs.

  Read the article

• Archlinux/atheros WLAN configuration troubles

  - by GrinReaper

  I'm trying to config archlinux to use my wireless network adapter. It's quite troublesome. From what I've gathered, it's an atheros network adapter, using the ath5k driver/module... I can't get it to work; any ideas? Here's some of the output from my tinkering: # lspci | grep -i net 00:0a.0 Ethernet controller: nVidia corporation MCP67 Ethernet (reva2) 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) # lsusb ... Bus 004 Device 003: ID 03f0:17d Hewlett Packard Wireless (Bluetooth + WLAN Interface [Integrated Module] # ping -c 3 www.google.com ping: unknown host www.google.com #ping -c 3 8.8.8.8 ping: network is unreachable # lspci -v 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) ... Kernel driver in use: ath5k Kernel modules: ath5k # dmesg |grep ath5k registered as phy0 registered led device ath5k: atheros chip found PCI INT A disabled registered led device registered as phy1 # ip addr | sed '/^[0-9]/!d;s/: <.*$//' 1: lo 2: eth1 3: eth0 # ip link set <interface> up/down RNETLINK answers: Operation not possible due to RF-kill Also, is there a way to dump text from command-line to a text file so i can just copy pasta? Sorry, first time using a linux distro... EDIT: So I just tried this: I actually just did this twice. (I can't tell which setting is on/off for my wireless adapter. The lights are blue all the time now.) #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :yes 1: hp-bluetooth: bluetooth softblocked: no hardblocked :yes 3: phy1: wireless lan softblocked: no hardblocked :yes #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :no 1: hp-bluetooth: bluetooth softblocked: no hardblocked no 3: phy1: wireless lan softblocked: no hardblocked :yes 7: hci0: bluetooh 0: hp-wifi: wireless lan softblocked: no hardblocked :no I've dug around some other articles and it seems like ath5k is supposed to be preferable to madwifi, so should i be using madwifi? I'm 99% sure I disabled the hardblock (by turning it ON) but, as shown above, phy1 wireless lan is STILL hardblocked. What gives? Maybe I've made some more fundamental error in a basic config file? EDIT: I've fixed the hardblock. I've tried pinging www.google.com, but to no avail. I get: ping: unknown host www.google.com In the arch wiki: Edit /etc/hosts and add the same HOSTNAME you entered in /etc/rc.conf: 127.0.0.1 archlinux.domain.org localhost.localdomain localhost archlinux To my understanding, hostname is just a user-specified and based on preference(?) My /etc/rc.conf: HOSTNAME="gestalt" My /etc/hosts: 127.0.0.1 localhost.localdomain localhost gestalt but should it be the following? 120.0.0.1 localhost.domain.org localhost.localdomain localhost gestalt

  Read the article

• Possible to use Python with Intel's Atom Developer SDK (C/C++)?

  - by Jordan Magnuson

  So I've made a game in Python and PyGame. Now I'm interested in submitting the game to Intel's March Developer Challenge. However, the developer challenge requires use of Intel's Atom Developer SDK (http://appdeveloper.intel.com/en-us/sdk), which only has API's for C and C++. I'm new to Python and PyGame, and have no experience in C or C++. My question is, would it be possible to somehow implement Intel's Atom SDK through/with/from a Python application (as the first link above suggests)? I've read up a little bit on embedding/extending Python into/with C, but I'm not entirely sure what to embed or where. I mean, I know I can do things like this in C: #include <Python.h> int main(int argc, char *argv[]) { Py_Initialize(); PyRun_SimpleString("from time import time,ctime\n" "print 'Today is',ctime(time())\n"); Py_Finalize(); return 0; } But what do I do about all my dependencies on Python and Pygame, for people that don't have those installed on their machines? Normally Py2Exe takes care of compacting the required dependencies (I've managed to package my game into an exe/zip), but how do I take care of that stuff in the context of embedding within C? Can I somehow work with py2exe on this, or do I need to do something entirely different for embedding within C? It seems like it would be a lot easier to go the route of extending Python with the C validation code, rather than trying to embed my whole game within C, but I think that's not an option, "because the library provided is currently only available as a Visual Studio 2008 '.lib'", meaning the application has to be compiled with Visual Studio...? Any help, thoughts, or ideas are much appreciated! You can find the complete SDK Developer's Guide on the intel site above, but here is their "Hello World" using the C Language API: #include <stdio.h> #include “adpcore.h” int main( int argc, char* argv[] ) { ADP_RET_CODE ret_code; const ADP_APPLICATIONID myApplicationID = {{ 0x12345678,0x11112222,0x33331234,0x567890ab}}; if ((ret_code = ADP_Initialize()) != ADP_SUCCESS ){ printf( “ERROR: exiting” ); exit( -1 ); } if (( ret_code = ADP_IsAuthorized( myApplicationId )) == ADP_AUTHORIZED ) printf( “Hello World” ); else printf( “Not authorized to run” ); exit 0; } 35 Page SDK Developer Guide: http:// appdeveloper.intel.com/sites/files/pages/SDK%20Developer%20Guide.pdf

  Read the article

• Xorg server won't start after fresh install of Debian 5.04, screen goes blank (Intel Atom D510(Pinet

  - by Kamil Zadora

  Hello, I have installed Debian 5.04 Lenny on my new Intel D510MO motheboard. I fixed some issues with incorrect drive mapping (for some reason during installation my hdd was on sdb, after a restart it is under sda - fixed in grub), and now I am struggling with getting graphical enviroment up and running, I installed the graphical enviroment using the Debian installer. I am not an linux expert by any means, I assume that I need to edit the xorg.conf file. Any hints appreciated! UPDATE1: No change after dpkg-reconfigure xserver-xorg Here is my current xorg.conf: # xorg.conf (X.Org X Window System server configuration file) # # This file was generated by dexconf, the Debian X Configuration tool, using # values from the debconf database. # # Edit this file with caution, and see the xorg.conf manual page. # (Type "man xorg.conf" at the shell prompt.) # # This file is automatically updated on xserver-xorg package upgrades *only* # if it has not been modified since the last upgrade of the xserver-xorg # package. # # If you have edited this file but would like it to be automatically updated # again, run the following command: # sudo dpkg-reconfigure -phigh xserver-xorg Section "InputDevice" Identifier "Generic Keyboard" Driver "kbd" Option "XkbRules" "xorg" Option "XkbModel" "pc105" Option "XkbLayout" "pl" EndSection Section "InputDevice" Identifier "Configured Mouse" Driver "mouse" EndSection Section "Device" Identifier "Configured Video Device" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" EndSection UPDATE2: I have installed vnc4server package. I can connect over vnc from my windows 7 laptop and i see empty desktop with terminal window open. Seems that the xserver and gdm are running but they cant talk with my GPU. I am not sure if a can use any gui tool to configure it overthe vnc, as all I see is the terminal window, no taskbars etc. UPDATE3: My current Xorg.0.log http://pastebin.pl/18918 The graphic chipset integrated into the D510 processor is Intel 945GC

  Read the article

• (Mac Intel) HP PS driver prints in B&W from Adobe Reader after installing Cannon PS driver

  - by John B

  I have a unique problem that leaves me at a loss as to where to start troubleshooting. We have three Macs we use for graphics, two of which are PowerPC and one which is Intel. They are set up to print to an HP 5500dn, but occasionally this printer gets tied up with a massive print job, so I installed the PS driver (iR-PSv1.81MacOSX) for the Cannon C3200 Printer/copier on each of the machines. Both of the PowerPC Macs installed without issue, but the Intel Mac exhibits strange behavior: I've confirmed that while the Cannon driver is installed (whether or not the Cannon is set up for printing in print settings), the HP 5500dn will print in color from Safari, but only prints in black and white from Adobe Reader. The Cannon printer itself has not exhibited any strange behavior As soon as the Cannon driver is uninstalled, the HP 5500dn prints in color from Adobe Reader again. We run a network of Windows PCs, and the 'Mac room' mostly takes care of itself, so we don't have any experienced Mac administrators onsite. The Cannon is capable of Appletalk, but the PS driver seemed easier to work with (and Appletalk is currently disable on the Cannon. I'm not against using the Appletalk compatible drivers, but I would rather use the PS driver if at all possible - I don't want to open up the proverbial can of worms. If someone has any clues or suggestions that would help troubleshoot this problem, I would be grateful. I've already done some googling, but due to the obscure nature of this problem, I haven't been very successful.

  Read the article

• Cannot find wireless driver for HP laptop

  - by rodey

  I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

  Read the article

• How to Turn Your Ubuntu Laptop into a Wireless Access Point

  - by Chris Hoffman

  If you have a single wired Internet connection – say, in a hotel room – you can create an ad-hoc wireless network with Ubuntu and share the Internet connection among multiple devices. Ubuntu includes an easy, graphical setup tool. Unfortunately, there are some limitations. Some devices may not support ad-hoc wireless networks and Ubuntu can only create wireless hotspots with weak WEP encryption, not strong WPA encryption. HTG Explains: What Is RSS and How Can I Benefit From Using It? HTG Explains: Why You Only Have to Wipe a Disk Once to Erase It HTG Explains: Learn How Websites Are Tracking You Online

  Read the article

• compiling compat-wireless fails at 'make' with 'make: *** [modules] Error 2'

  - by Paul Carter

  Trying to compile the compat-wireless-2012-09-25 driver module, without success. scrips/driver-select alx ; works make ; fails - scripts/Makefile.build:44 ~/sourcecode/compat-wireless-2012-09-25.2/drivers/net/ethernet/atheros/alx/Makefile: No such file or directory make[4]: ** No rule to make target '~/sourcecode/compat-wireless-2012-09-25.2/drivers/net/ethernet/atheros/alx/Makefile'. Stop. [snip] make: * [modules] Error 2 Device is Atheros AR8161 wired ethernet in a Dell Vostro 3460. I'd be very grateful for assistance in getting this to compile.

  Read the article

• DD-WRT Acces Point as a Router

  - by Dzh

  Following suggestion to this question asked on Network Engineering, I am asking the question here. this is an extension to my previous question (I think it was deleted), where I was claiming that DDWRT was disabling it's DHCP server once connected to the network. I was wrong, as it now seems that it is bridging itself with another parallel connected wireless router. I have two Draytek 2820 and one Netgear WG602v3 with latest DDWRT. Lets call one wired-Draytek and it has wireless disabled. The other one, let's call it wireless-Draytek, is connected to wired-Draytek and has wireless with MAC filtering enabled. Once I connect Netgear to the wired-Draytek, the client that connects to Netgear, will be assigned with IP address from the wireless-Draytek. If the MAC address is not on the wireles-Draytek, the client is unable to obtain IP address and has no connectivity at all, even with manually assigned static IP configuration. To illustrate further, this is how network is set up: wired-Draytek ---------- wireless-Draytek \_________ Netgear What I wish to have, is that Netgear issues IP addresses from it's own IP pool and ignores the MAC filtering rules from wireless-Draytek. This is kind of puzzling how this they are bridging (if they are) themselves automatically. Thanks. UPDATE: It's not a home network. I gave you a bit simplified set-up. If there is a better site on Stack Exchange to ask this, please let me know. The Drayteks are running stock firmware, it's only Netgear that I've flashed to get more stability. In addition to these routers, I have also three 3COM Baseline switch 2824, and another Draytek router with Prosafe FS752TP PoE switch dedicated for VoIP phones. Wired-Draytek has IP 10.0.0.1, DHCP disabled as there is AD DC which is issuing IP addresses. Wireless-Draytek has IP 1.1.1.1 and DHCP enabled. Netgear has default - 192.168.1.1. As per suggestion, the specific question is - how do I isolate these two wireless routers?

  Read the article

• Broadcom STA wireless driver frezees

  - by Srki

  Upon updating my 10.10 netbook to 11.04 on the first startup it froze. I checked the forums and found that disabling wlan in BIOS fixes the problem so I did that and it worked, system was ok and it didn't freeze but then I had no wireless. I know that Broadcom STA driver is to blame cause I removed it from "additional drivers" and enabled back in bios wlan and everything worked fine (exept no wireless cause no driver is activated). Enabling Broadcom STA in the additional drivers again and restarting wireless was up and it found my network and connected to it but in a matter of seconds netbook froze. Can you please help me...

  Read the article

• Can you explain how to understand what the 'iwconfig' command displays in Ubuntu-9.04?

  - by Shawn

  I'm having trouble making my wireless connection work, and I realized I don't really know how to use the tools I have, in this case, the iwconfig command in Ubuntu-9.04. Here is what I get: ***iwconfig*** - lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Network" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=20 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 vboxnet0 no wireless extensions. pan0 no wireless extensions. "Network" is the name of my wireless network, btw. But what does this all mean? How can this information help me aquire a working wireless connection? When I try associating a key using sudo iwconfig wlan0 key s:my_key I get the following error message: Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; Invalid argument. I do have the right key though, so what's the problem?

  Read the article

• Can you explain how to understand what the 'iwconfig' command displays in Ubuntu-9.04?

  - by Shawn

  I'm having trouble making my wireless connection work, and I realized I don't really know how to use the tools I have, in this case, the iwconfig command in Ubuntu-9.04. Here is what I get: ***iwconfig*** - lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Network" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=20 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 vboxnet0 no wireless extensions. pan0 no wireless extensions. "Network" is the name of my wireless network, btw. But what does this all mean? How can this information help me aquire a working wireless connection? When I try associating a key using sudo iwconfig wlan0 key s:my_key I get the following error message: Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; Invalid argument. I do have the right key though, so what's the problem?

  Read the article

< Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63  | Next Page >