Search Results

Search found 21644 results on 866 pages for 'connection speed'.

Page 562/866 | < Previous Page | 558 559 560 561 562 563 564 565 566 567 568 569  | Next Page >

• Can Current Backflow from Powered Hub's Adapter & cause PC Damage?

  - by SuperUserMan

  Getting this short: Can current flow from a powered USB hub's power adapter (lying 10 Meter away) back to computer via usb port and cause damage to Computer components like mobo, etc? What should be my concerns? Using a 2 Amp 5V Power adapter to power a 10m Long Active Repeater USB extension cable with 4 port HUB & plugging into PC's Front port, causes PC Chassis fan to keep running (thought slower than regular speed) Front Chassis HDD & power LED to turn on (though bit dim) may be other things which i cant detect/see at chip level, in motherboard?? All this even after PC is shut down (bit scary) More detail (in case still want to read): To run 4 High power (needing 450 mAmps) Wifi Adapters, far away from PC, Bought Active Repeater USB Extension Cable with 4 Ports & power port at far end http://www.ebay.com/itm/33FT-USB-2-0-Male-to-Female-Extension-Cable-Hub-Splitter-Adapter-with-4-USB-Port-/390846115254 Then added a locally bought 2 Amp 240V AC to 5V DC Power Adapter and plugged into USB hub which is a part of & situated at far end of a 10 Meter Active Repeater usb extension cable. Even 4 Wifi Adapters run fine (appear to) using this setup, but running chassis fan, dimly lighted Power & HDD LED, even when PC is switched off is bit scary and surely mean 5V & some current is flowing all though that 10 meter extension cable into my USB port & powering stuff. Can this cause damage? and what should be my concerns. Of course I can't switch off the power adapter (lying 10 meters away from PC) every time I switch off my PC to prevent this.

  Read the article

• Non-alphanumeric character folder name auto-completion problems

  - by viking

  I have been working with Windows 7's command line and have some folders that begin with non-alphanumeric characters. When I try to use tab completion to complete the folder name, the initial character is not included inside of the quotation marks. Example: C:\Users\username\!example is the folder I want to get into, but when I type: cd ! and press <Tab> to autocomplete, it will complete to cd !"!example" instead of the expected cd "!example" Any ideas on how to fix this besides changing the folder names? EDIT: I realize I could just tab through the entire list after entering cd, but I'm looking for a way to speed up the process. I have been spending a significant amount of time navigating these folders. UPDATE: This also happens if there is a space in the directory. For example: "c:\Program Files". In order to continue using tab to complete, first the second quote has to be deleted. C:\Program press Tab "C:\Program Files" is what appears. To navigate to a subdirectory, first the quote after Program Files has to be deleted before the next directory can be spelled out.

  Read the article

• Solaris 10 invalid ARP requests from 0.0.0.0? Link up/down every hour or 2

  - by JWD

  The guys at the data center where I'm hosting a server running Solaris 10 are telling me that my server is making a lot of invalid arp requests. This is an example of a portion of what was sent to me from the logs (with Mac addresses and IP addresses changed). [mymacaddress]/0.0.0.0/0000.0000.0000/[myipaddress]/[Datestamp]) It's being logged every hour. I don't see anything in the arp tables (arp -a) or routing tables (netstat -r) and I don't see anything relating to 0.0.0.0 when snoping the arp requests. The only place I see any reference to 0.0.0.0 is if I do netstat -a for the SCTP SCTP: Local Address Remote Address Swind Send-Q Rwind Recv-Q StrsI/O State ------------------------------- ------------------------------- ------ ------ ------ ------ ------- ----------- 0.0.0.0 0.0.0.0 0 0 102400 0 32/32 CLOSED But not really sure what that means. Doesn't seem like I can disable SCTP. There are some tunable SCTP parameters but it's not something I'm familiar with. Do I have to add changes to /etc/system? Looks like sctp_heartbeat_interval might be what I need to change? If it makes any difference, I have a few solaris zones running on this server, each with their own IP address on a virtual interface. eth0:0, eth0:1, etc. Does anyone have any idea what might be causing this and how to stop it? I think the switch I'm connected to doesn't like it and momentarily drops the connection. Is there anyway to at least block those requests using ipfilter or something else? Update: This was happening more frequently but now it seems to be happening roughly every hour or every two hours. It's not consistent. I tried setting setting the link speed and duplex to match the switch port and that seemed to make it stop happening for a few hours but then it started again.

  Read the article

• VirtualServer reverseproxy works locally, but not from client

  - by Yep

  Setup: 2 Webservers pointed to 127.0.0.1:8080 and :8081. Curl validates they work as expected. Apache with the following virt hosts: NameVirtualHost 192.168.1.1:80 <VirtualHost 192.168.1.1:80> ServerAdmin [email protected] ProxyPass / http://127.0.0.1:8080/ ProxyPassReverse / http://127.0.0.1:8080/ ServerName 192.168.1.1 ServerAlias http://192.168.1.1 </VirtualHost> NameVirtualHost 192.168.1.2:80 <VirtualHost 192.168.1.2:80> ServerAdmin [email protected] ProxyPass / http://127.0.0.1:8081/ ProxyPassReverse / http://127.0.0.1:8081/ ServerName 192.168.1.2 ServerAlias http://192.168.1.2 </VirtualHost> On the server I can curl to the virtualhosts and receive appropriate responses. (curl 192.168.1.1 gives me the webservers response from localhost:8080, etc) remote hosts cannot however connect to 192.168.1.1 or .2 at all. What am I missing? Re: comments Yes, the default directory Directive is still in place. # Deny access to root file system <Directory /> Options None AllowOverride None Order Deny,Allow deny from all </Directory> No apache logs are generated when trying to reach 192.168.1.1 remotely. They do get generated when curl from local. If I point the webservers to *:8080 and *:8081 instead of binding to localhost, I can access them from a remote host via 192.168.1.1 and 192.168.1.2 if i specify the 8080 and 8081 ports (both ports work on both IP's, which is what I'm trying to avoid with apache reverse proxy bind to 80 on each interface) Edit2: curl verbose output: (similar for second webserver, and for 127.0.0.1:portnum) [user@host mingle_12_2_1]$ curl -v 192.168.1.1 * About to connect() to 192.168.1.1 port 80 * Trying 192.168.1.1... connected * Connected to 192.168.1.1 (192.168.1.1) port 80 > GET / HTTP/1.1 > User-Agent: curl/7.15.5 (x86_64-redhat-linux-gnu) libcurl/7.15.5 OpenSSL/0.9.8b zlib/1.2.3 libidn/0.6.5 > Host: 192.168.1.1 > Accept: */* > < HTTP/1.1 302 Found < Date: Tue, 16 Oct 2012 16:22:08 GMT < Server: Jetty(6.1.19) < Cache-Control: no-cache < Location: http://192.168.1.1/install < X-Runtime: 130 < Content-Type: text/html; charset=utf-8 < Content-Length: 94 < Connection: close Closing connection #0 <html><body>You are being <a href="http://192.168.1.1/install">redirected</a>.</body></html> log from the request local 192.168.1.1 - - [16/Oct/2012:12:22:08 -0400] "GET / HTTP/1.1" 302 94 no apache access log or error log generated when requests from remote clients.

  Read the article

• replacing buffalo lonkstations with FreeNAS, overall backup strategy, am I on the right path?

  - by Shreko

  We've been using 2 Buffalo LinkStations of 320Gb each for shared directory and employee's server storage (around 20 employees). So only documents (word, excel, cad drawings etc.) and database backup of the main application server (ERP, Accounting) 1 buffalo box serves as a main one, located at the server room, next to the main application server and the other buffalo box is located on the opposite side of the building (for fire protection) in a secure storage room and backs up the first one. We also have several external HDs that backs up everything from the buffalo box for an offsite backup. After 3.5 years of using these, capacity is a main limitation, I'm planning a replacement and would like to use FreeNAS (we already use monowall with great success). I would like to keep it simple and continue similar setup, building two low power boxes with 1 hd (2Tb) each. Is low power atom mobo OK? Not sure about HDs? I've read on this site somebody mentioning more seagate ES2 as more reliable and better performing. How would those eco/green drives compare. We've been pretty happy with speed of Buffalo boxes and I don't want my users to notice any slowdown. Any suggestion?

  Read the article

• How to create a software raid5 array without a spare

  - by Yannick M.

  I am trying to create a software raid5 array using mdadm: $ linux # mdadm --create --verbose /dev/md0 --level=5 --raid-devices=4 --spare-devices=0 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 mdadm: layout defaults to left-symmetric mdadm: chunk size defaults to 64K mdadm: array /dev/md0 started. However when inspecting /proc/mdstat Personalities : [raid6] [raid5] [raid4] md0 : active raid5 sdd1[4] sdc1[2] sdb1[1] sda1[0] 2930279808 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 0.3% (2970496/976759936) finish=186.1min speed=87172K/sec unused devices: <none> It seems one drive isn't active, so I check the details of the array: /dev/md0: Version : 00.90.03 Creation Time : Tue Jul 21 16:29:53 2009 Raid Level : raid5 Array Size : 2930279808 (2794.53 GiB 3000.61 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 4 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Jul 21 16:29:53 2009 State : clean, degraded, recovering Active Devices : 3 Working Devices : 4 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 64K Rebuild Status : 0% complete UUID : ce8b2f40:821d003c:0027688e:a70977ec Events : 0.1 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 2 8 33 2 active sync /dev/sdc1 4 8 49 3 spare rebuilding /dev/sdd1 And it seems there are only 3 active devices, with one spare. Is it just me, or something wrong here?

  Read the article

• Openvpn issue with linux

  - by catsy

  So I've tried to setup openvpn, I followed some guide but it's stuck att "initialization sequence completed" with no connection and I can't find any working solution... here's the log: $Sun Sep 23 19:14:32 2012 OpenVPN 2.1.0 i486-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 20 2010 Enter Auth Username:pumpedup Enter Auth Password: Sun Sep 23 19:14:37 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Sun Sep 23 19:14:37 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Sun Sep 23 19:14:37 2012 LZO compression initialized Sun Sep 23 19:14:37 2012 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Sun Sep 23 19:14:38 2012 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Sun Sep 23 19:14:38 2012 Local Options hash (VER=V4): '41690919' Sun Sep 23 19:14:38 2012 Expected Remote Options hash (VER=V4): '530fdded' Sun Sep 23 19:14:38 2012 Socket Buffers: R=[163840-131072] S=[163840-131072] Sun Sep 23 19:14:38 2012 UDPv4 link local: [undef] Sun Sep 23 19:14:38 2012 UDPv4 link remote: [AF_INET]192.162.102.162:1194 Sun Sep 23 19:14:38 2012 TLS: Initial packet from [AF_INET]192.162.102.162:1194, sid=87a95723 a6d7b7f9 Sun Sep 23 19:14:38 2012 WARNING: this configuration may cache passwords in memory -- use the auth-nocache option to prevent this Sun Sep 23 19:14:38 2012 VERIFY OK: depth=1, /C=NV/ST=NV/L=nVPN/O=nVpn/CN=nVpn_CA/[email protected] Sun Sep 23 19:14:38 2012 VERIFY OK: depth=0, /C=NV/ST=NV/L=nVPN/O=nVpn/CN=server/[email protected] Sun Sep 23 19:14:39 2012 WARNING: 'link-mtu' is used inconsistently, local='link-mtu 1542', remote='link-mtu 6042' Sun Sep 23 19:14:39 2012 WARNING: 'tun-mtu' is used inconsistently, local='tun-mtu 1500', remote='tun-mtu 6000' Sun Sep 23 19:14:39 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Sun Sep 23 19:14:39 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sun Sep 23 19:14:39 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Sun Sep 23 19:14:39 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sun Sep 23 19:14:39 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Sun Sep 23 19:14:39 2012 [server] Peer Connection Initiated with [AF_INET]192.162.102.162:1194 Sun Sep 23 19:14:41 2012 SENT CONTROL [server]: 'PUSH_REQUEST' (status=1) Sun Sep 23 19:14:41 2012 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1,dhcp-option DNS 8.8.8.8,dhcp-option DNS 8.8.8.8,route 10.102.162.1,topology net30,ping 10,ping-restart 120,ifconfig 10.102.162.6 10.102.162.5' Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: timers and/or timeouts modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: --ifconfig/up options modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: route options modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified Sun Sep 23 19:14:41 2012 ROUTE default_gateway=10.0.2.2 Sun Sep 23 19:14:41 2012 TUN/TAP device tun0 opened Sun Sep 23 19:14:41 2012 TUN/TAP TX queue length set to 100 Sun Sep 23 19:14:41 2012 /sbin/ifconfig tun0 10.102.162.6 pointopoint 10.102.162.5 mtu 1500 Sun Sep 23 19:14:41 2012 /sbin/route add -net 192.162.102.162 netmask 255.255.255.255 gw 10.0.2.2 Sun Sep 23 19:14:41 2012 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 /sbin/route add -net 10.102.162.1 netmask 255.255.255.255 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 Initialization Sequence Completed

  Read the article

• LG LW20 Express won't boot after hdd replace

  - by Mika

  My old laptop (LG LW20 Express) got a hdd failure and I replaced the hdd. Now the laptop won't boot from cd or usb. I'm trying to install ubuntu on it. When I turn the laptop on it shows me the startup screen but when it should be the time to load operating system it just gives a black screen and starts over. This loop continues until I shut down the laptop. I created the usb boot drive following this guide https://help.ubuntu.com/community/Installation/FromUSBStick/ I used my boot cd to install ubuntu on this machine I'm using right now. So at least the cd should work. From the BIOS I can see that my newly installed hdd is recognized and put as a secondary master. Also the cd and removable media are in the boot list before hdd. The laptop runs pretty hot. The fan is at full speed pretty soon after the laptop is turned on. Earlier I suspected that it would have been the almost broken hdd that would have produced that heat but there obviously is something else also. Any ideas what to check?

  Read the article

• Why do hosts prefer Linux to Windows Server?

  - by iconiK

  So far I see a HUGE majority of hosts provide only Linux shared hosting, providing Windows only to VPS (or even to only dedicated servers). Why is it so? While Windows is a lot more expensive than Linux (though it depends on a lot of factors, not just initial and support license cost), it also provides ASP.NET, IIS and of course, Microsoft SQL Server. I know in the past it might have been because of cPanel being Linux only but now they have a Windows version. But still, why is Linux predominantly used on shared hosting? PHP works on both systems. IIS can be (and probably is) faster. MySQL runs on both systems as well. cPanel has a Windows version. Python, Perl, Ruby, all run on Windows as well. You even have MS SQL Server Express, which I find more superior than MySQL in both speed and features. Access is there for low usage requirements, as is SQLite (which is so great for quick small stuff). And with PowerShell you have a good alternative to the Unix shell. EDIT: I am looking for common reasons, I realize each hosting company (and/or it's clients) may have different needs. This becomes very important when you get to VPS or Cloud which give you a full operating system to use.

  Read the article

• NFS confusion - writing many small files

  - by Antonis Christofides

  I have a Debian squeeze amd64 which is at the same time a NFS4 server and client (it mounts itself through NFS4). The local directory that leads directly to disk is /nfs4exports/mydir, whereas /nfs4mounts/mydir is the same thing mounted through NFS, using the machine's external IP address. Here is the line from fstab: 176.9.116.102:/mydir /nfs4mounts/mydir nfs4 soft 0 0 I have an application that writes many small files. If I write directly to /nfs4exports/mydir, it writes thousands of files per second; but if I write to /nfs4mounts/mydir, it writes 4 files per second or so. I can greatly increase speed if I add async to /etc/exports. (Writing a single large file to the NFS directory goes at more than 100 MB/s.) I am confused by the description of async in NFS. If my application accesses the local directory, system calls like write and close return even if caches have not been flushed to permanent storage. Apparently this is not true with NFS sync behaviour. However, with NFS async behaviour, even calls like fsync are ignored. Isn't it possible to work like local files, i.e. generally work asynchronously, but honour fsync and O_SYNC?

  Read the article

• why does my computer crash?

  - by chobo2

  Hi my computer keeps crashing and I don't know why. At first I thought because I had my cpu over clocked that it all of sudden was crashing. So I set my cpu back to regular speed. This did not help. I then thought it was because 2 sticks of my memory where from a computer that suffered from a power surge. However I just ran the windows memory diagnostic tool( extended) and after like 6 hours of testing my memory it found no errors. So now the only thing that is left is windows 7 64bit. I first over clocked my cpu for a couple months while running XP. Never had a problem. I installed the memory and windows 7 at the same time. But I not sure if it is my memory now since it passed the diagnostic tests. However I am not sure if it is windows 7 either has I installed it twice in the last year. I really don't want to go back to XP to find out if this is the case. So here are my blue screens of deaths(from bluescreen). https://sites.google.com/site/myerrorswin7/errors (I hope you enjoy my great site lol) As you can see most of them are different NTFS_FILE_SYSTEM KMODE_EXCEPTION_NOT_HANDLED BAD_POOL_HEADER IRQL_NOT_LESS_OR_EQUAL SYSTEM_THREAD_EXCEPTION_NOT_HANDLED SYSTEM_SERVICE_EXCEPTION

  Read the article

• Terminal Server in Windows Server 2003

  - by Hemal

  I have a confusion regarding what I am doing here. At present I have a Windows Server 2003 server with SP2. I have assigned RAS/VPN server role to it (through Manage my server wizard) and in my router, I setup the IP address of my RAS/VPN server as PPTP server. Staff leave their workstations ON all the time and access them from home through RDP. They first connect thorugh VPN & in the RDC they simply type their respective IP or computer name to access the office network from home. Everything works fine so far except: Staff have to leave compuers always ON in the office Speed is very slow depend how many staff members access the VPN network I was told to install and configure Terminal service to improve this situation. I already added TS Role in the server but I don't know how to clients can access the TS server from home or remote location. I really appreciate any good links or guidence from the experts in this group regarding this. Thank you in advance for any replies!

  Read the article

• How to handle sh: fetch: command not found

  - by Tyler Johnson

  Okay, I'm a noobie. I know how to build and compose a website, but I have no idea what I'm doing when it comes to servers and server commands, etc. I've recently had a problem with all of my sites on our servers going down all at once and then I have to go in and reboot the server for them to come up again. At first this was annoying, but now it is becoming agonizing as it now takes 3-4 reboots for the websites to come back up. I contacted support for my hosting, but they are not being very helpful. They just keep telling me what the issue might be and basically telling me that I'm going to have to look into it and figure it out, which really isn't possible since I know nothing. Anyway, here are the things they said were possible reasons: They said I have "strange logs" in my Apache webserver log, error: sh: fetch: command not found. My php.ini memory limit is: 256M which is very high. It should be 32M or 64M. Server is reaching Max Clients, meaning we have more than 150 visitors at a time. (They supposedly "fixed" this, but the sites/server are still going down) I have some Wordpress sites with plugins getting errors like: PHP Warning: pack(): Type H: illegal hex digit G in... PHP Fatal error: Cannot use object of type stdClass as array in... PHP Fatal error: Maximum execution time of 30 seconds exceeded in... PHP Fatal error: Call to undefined function file_exists() in... PHP Parse error: syntax error, unexpected '<' I know that's a lot, but I really am at wits end and have no idea what to do now. If anyone could maybe give me some advice or point me in the right direction I would greatly appreciate it! Thanks! Oh, and here are the specs for my server: RAM: 2048MB CPU Shares: 40 Primary Disk: 50GB Data Transfer: 75GB Port Speed: 5Mbps

  Read the article

• In an environment with multiple WiFi access points, do wireless clients sometimes connect to both at the same time?

  - by Bobby Burgess

  This is more of a curiosity than a problem, but in this new office I have two D-link DAP-2553's connected in a master/slave array (this just means the master keeps certain configuration options aligned with the slave). The network is set to 802.11n-only, and each AP has the same SSID and WPA2 key. The only difference is that they are on different channels (1 and 11). The WiFi network itself is working well. Users can roam around and the signal/speed is fairly consistent. However, I notice that when I look at the 802.11 client list in the web admin page for each of the 2 APs, I see that certain clients are connected to both, for extended periods of time, but I assume they are only passing data through one of them. Not every client is seen on each AP, but at any given time the same MAC address of a WiFi adapter can be associated (and remain associated) with both APs. The client list auto-refreshes every few seconds so I believe I'm looking at the most recent rather than stale information. One of the WiFi adapters that consistently associates with both APs is an Intel Centrino Wireless-N 1030 (laptop chip). Is it part of the WiFi standard that more than one association per WiFi card can be established concurrently on separate APS?

  Read the article

• How to move or delete files from a folder containing 2 million files on an NTFS drive?

  - by Beau

  The issue is that any modification to the directory locks up Explorer indefinitely, though Samba access to other directories still works. I've tried moving files locally and over Samba. Even enumerating the directory to get the list of files locks up the computer indefinitely. I tried using Python's win32file.FindFilesIterator to iterate the files but that also hangs. My idea was to move each file to a different directory (in a directory above the directory we're dealing with) based on its timestamp, so that we'd have at most a thousand or so files in each directory... But since I can't even enumerate the files, that's been a non-starter. If I have to give up and just nuke the directory I'm willing to do that, but a standard delete also hangs indefinitely. I have set these two parameters to increase speed and they also did not help the issue: R:\>fsutil behavior query disablelastaccess disablelastaccess = 1 R:\>fsutil behavior query disable8dot3 disable8dot3 = 1 These are all sequential images that would have run into the 'bug' with 8.3 filenames whereby many similarly named files in one directory can take a long time to compute 8.3 filenames. From what I understand this data is stored in the file system even after disable8dot3 is enabled, so it may still be contributing to the problem. Any ideas?

  Read the article

• How to interrupt software raid resync?

  - by Adam5

  I want to interrupt a running resync operation on a debian squeeze software raid. (This is the regular scheduled compare resync. The raid array is still clean in such a case. Do not confuse this with a rebuild after a disk failed and was replaced.) How to stop this scheduled resync operation while it is running? Another raid array is "resync pending", because they all get checked on the same day (sunday night) one after another. I want a complete stop of this sunday night resyncing. [Edit: sudo kill -9 1010 doesn't stop it, 1010 is the PID of the md2_resync process] I would also like to know how I can control the intervals between resyncs and the remainig time till the next one. [Edit2: What I did now was to make the resync go very slow, so it does not disturb anymore: sudo sysctl -w dev.raid.speed_limit_max=1000 taken from http://www.cyberciti.biz/tips/linux-raid-increase-resync-rebuild-speed.html During the night I will set it back to a high value, so the resync can terminate. This workaround is fine for most situations, nonetheless it would be interesting to know if what I asked is possible. For example it does not seem to be possible to grow an array, while it is resyncing or resyncing "pending"]

  Read the article

• How to diagnose and solve an erratic "HDCP Support Required"?

  - by Jom Orgstrom

  I am playing a digital tv broadcast on Windows Media Center for Windows 7. I built this system so it works with HDCP, and in fact I have been able to watch tv and bluray before with this same computer. However, I suddenly started getting an "HDCP Support Required" error from WMC. The entire message is as follows: HDCP Support Required High-bandwidth Digital Content Protection (HDCP) may not be supported by the current video card. Use an HDCP-compliant display, video card, and video driver. Or, connect using an analog connection such as component or VGA. Relevant specs are: CPU: Ivy Bridge Core i7-3770 Motherboard: Asus P8H77-I Memory: 16GB DDR3-1600 Graphics: Radeon HD 7850 (Driver by AMD, version 8.982.0.0 built on 2012/07/27) Display: Acer P243w connected by HDMI Sound: Roland Quad-Capture (It complains even when I use the bundled VIA HD Audio) TV Tuner: I-O Data GV-MC7/HZ3 OS: Windows 7 Professional SP1, Windows Update enabled. All patched and up to date. As you can see, there is nothing weird or old about my setup. I am also not doing anything strange, not doing any overclocking, weird system changes and so on. One thing that does happen from time to time, is that the display goes black for a few seconds (sometimes when watching media contents, sometimes when just using photoshop or Visual Studio). This happened with my previous setup as well, so I'd be inclined to think it is a display or cable issue (apart from the BD drive, these are the only things I kept from my previous setup to this one). But being a digital transfer, as far as I know, these things either work or not. Never erratically or with decreased quality. The thing is that sometimes I can watch the TV, sometimes not. This happens with recorded programs as well, so it's not a per-program thing. Sometimes rebooting helps, sometimes it doesn't. Sometimes unplugging and plugging back the HDMI connector helps, sometimes it doesn't. Sometimes doing so doesn't even turn the screen back on, so I have to reboot. Unfortunately, WMC's error message is quite unhelpful. I'd like to know exactly where the problem is, so I can solve it. I don't want to buy a brand new display just to then find out it was a registry setting that was misconfigured. I've tried looking at the system event viewer, but these errors don't show up at all in there. Other people who have this problem seem to have a setup that is not HDCP compliant, so I turn to you guys here. Anybody knows how to diagnose this problem? Edit: So I got the Cyberlink Blu-ray disc advisor. I ran it and told me everything was okay, except for the Video Connection Type, which showed as "Digital (without HDCP)". I then proceeded to unplug the power cable from the monitor, plugged it in again, ran the tool again, and now it's "Digital (with HDCP)". Needless to say, I can watch my TV and recorded programs on WMP again. I'm guessing that at some point, something may be slightly wrong with the HDCP setup, and Windows decides to reset the entire content protection path (which leads to the screen blanking out). Usually the reset succeeds, but sometimes it doesn't, so Windows defaults to turning HDCP off. There's no way to turn it back on, except by doing a hard reset of the display. I really want to know what the exact error was, so I can fix it. Is it the cable? is it the display? is it the video card? the driver? Also, is there any other way to try and turn HDCP on again without having to hard reset the display? Oh, questions, questions...

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• File server share access intermittent/slow/machine unstable: win2k8r2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• GlusterFS as elastic file storage?

  - by Christopher Vanderlinden

  Is there any way to run GlusterFS in a replicated mode, but with the ability to dynamically scale the volume up and down? Say you have 3 servers all running glusterd. your Gluster volume would have to be setup with replica 3 gluster volume create test-volume replica 3 192.168.0.150:/test-volume 192.168.0.151:/test-volume 192.168.0.152:/test-volume You would then mount it as say \mnt\gfs_test What happens when I want to add 2 more servers to the storage pool and then also use them in this volume? Is there any easy way to expand the volume AND increase that replica count to 5? My end goal is to run this on EC2 instances, say 3 Apache front ends, with the webroot setup on the gluster volume mount. My concern is that if I ever need to spin up a server, I would want the server to not only be an additional Apache front end, but also another server in the gluster file system, adding to fault tolerance as well as possibly giving a slight boost in read speed. Maybe there are better options that would fit the bill here? Thanks.

  Read the article

• Windows Server 2012 Hyper-V very slow

  - by Matt Taylor

  I have been running several Hyper-V VMs on Windows Server 2008 R2 for the past couple of years and enjoying perfectly adequate performance for my testing/development/r&d environments. I'm a software developer so my hardware knowledge is basic however I built the rig using: •Gigabyte GA-X58A-UD3R Intel X58 (Socket 1366) DDR3 Motherboard •Intel Core i7 960 3.20GHz (Bloomfield) (Socket LGA1366) •24GB triple channel RAM The host OS is running on an OCZ SSD and all the VMs are running on a 2TB Marvell SATA3 RAID 0 array consisting of 2 Western Digital Caviar Black 7,200rpm drives. I have tested the speed of the 2TB drive and appear to be getting less than 3Mbs but it can adequately run a 4 VM farm including a DC, (SQL) database and IIS application servers. I recently upgraded the SSD on which the host runs to a 256GB OCZ Vertex 4 and took the opportunity to upgrade to Windows Server 2012 and installed the Hyper-V role. I tried importing one of my existing Windows Server 2008 R2 VMs (and converted it to .vhdx) plus I have tried creating a brand new Windows Server 2008 R2 VM but both are running extremely slowly and I can see nothing obvious using the host and guest Task Manager/Resource Monitor tools. In both cases the VM has 8GB RAM (fixed), 4 CPUs, fixed size HD (not expanding) and is using an external virtual network running on a separate NIC to the host. I have upgraded the BIOS to the latest available version and checked the virtualization settings. I have run out of "obvious" (to a developer) things to check/configure and my next option will be to re-install the host OS but before I do I would very much appreciate any advice from any experts out there. Thanks

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• Varnish, Nginx, Apache, APC, Meteor, Cpanel & Wordpress On A Single Server, Any Good?

  - by Aahan

  Yes, I have read many close questions, but I needed a specific answer and hence this question. First, these are my new server specifications: Linux Server (CentOS), Intel Xeon 3470 Quad Core (2.93GHz x 4) processor, 4 GB DDR3 Memory, 1TB Hard Disk Space, 10 TB Bandwidth and 9 Dedicated IPs. AIM: To speed up my wordpress blog + Increase server's capacity to handle heavy load PLAN: This is how I am planning to setup my server - - VARNISH (in the front, to cache server responses) NGINX (to effectively handle static content & overcome the C10k problem) APACHE (behind Nginx, to effectively deliver dynamic content) APC (PHP page, database & object caching) CPANEL (which requires Apache, and I require it) WORDPRESS W3 TOTAL CACHE (caching plugin for Wordpress). So , will the setup work? Have anyone tried it? Please shower your thoughts and knowledge. NOTE: I can't do without Apache because I am used to that .htaccess & Cpanel stuff. So, it's not any option. All others are options. Please try to help. I hope I am clear in what I wanted to ask.

  Read the article

• What is the quickest and safest way to test new software and revert all changes, if needed?

  - by calbar

  I'm looking for Windows software that will allow me to quickly create a "checkpoint", do whatever I might need to do to my computer - install programs/drivers/updates, create/delete personal files, reboot the system multiple times, open questionable attachments - and then revert the entire system back to when the checkpoint was created. Essentially I want Windows Restore Points that save my personal files and partitions, too. It sounds like disk imaging might be the ticket, but creating them is much too slow and the restore process too involved... I'm hoping to sacrifice full disaster recovery for speed. Creating a checkpoint should be as close to one-click as possible, and rolling back should be a matter of selecting a restore point and rebooting. Ding! I'm familiar with Sandboxie, True Image Home "Try and Decide", Returnil, and a number of other "virtual system" apps that actively "catch" changes and allow you to commit or reject them. I'm not interested in these for a number of reasons - I prefer the "cut and dry" restore point approach. Finally, I'll note that I've just recently become aware of Comodo Time Machine. It sounds absolutely perfect, however, a quick skim through the user forums show more than a few horror stories of corrupted, unbootable systems. Any positive personal experience with the software to suppress my superstitions, or suggestions for more established alternatives would be greatly appreciated - Comodo Time Machine seems relatively new. Thanks for your help!

  Read the article

• httpd.config Easy Apache WHM CentOS

  - by jessie

  First let me explain how I got to this situation. I run a Streaming Video Site. Videos are about 100-250MB in size at any given time there are 500 people on the site. So I guess that would make then static. Recently My site started getting really slow and the only way to fix it temporarily was to restart apache. Now there was no change in traffic that could have caused this. My site is not being attacked. My hosting company recomended to implement mpm_mod and suPHP. They did that by using Easy Apache in WHMS. Then everything was working fine but a little slow. I researched around and to my understanding that mpm will do that but be more table. I was told that installing FastCGI would speed things up just enough. Well that made everything worse. The site is slow and time's out. I used WHM and took off fastCGI but its still the same, it seems like everything i do as of now nothing changes. I even did a roll back on the htconfig file but that didn't work. I'm not sure how to fix this. and my hosting network guy wont be able to touch the problem until Tuesday. I have root access.

  Read the article

< Previous Page | 558 559 560 561 562 563 564 565 566 567 568 569  | Next Page >