Search Results

Search found 21644 results on 866 pages for 'connection speed'.

Page 560/866 | < Previous Page | 556 557 558 559 560 561 562 563 564 565 566 567  | Next Page >

• Windows XP can use a wired network port, but MacBook (OS X) fails on the same port

  - by Dean Hill

  I wired the Cat5 in my house seven years ago. The wired ports have worked fine with both my Windows XP laptop and MacBook. My wireless network also works fine, but I like to use wired occasionally. One of the Cat5 runs wasn't terminated with a jack, so I recently terminated this wire with a port/jack on the wall end and a standard Cat5 plug on the end that plugs into my router. This is the same setup as my other runs. Unfortunately, the MacBook isn't working well with the new wired port. The OS X Network System Preferences show the IP, Subnet, Router, etc., and everything looks fine. A "netstat -ibd" shows no errors or dropped packets. However, when I open a page in Safari, the status says "Contacting 'www.google.com'" and appears to hang. If I wait for a couple minutes, part of the Google page starts to display, but it is still not the full page load. When I use a Windows XP laptop on the same wired port, everything works fine. An internet speed test shows good results and all web pages load fine. A "netstat -e" under Windows shows no errors. I've used a Cat5 tester, and the cable tests fine (wires 1-8 light up in sequence). I've replaced both the port/jack and the connector twice to make sure I wired things correctly. I'd really like this Cat5 to work with the MacBook (and I'm trying to avoid running a new length of cable). Any ideas what the problem could be?

  Read the article

• My desktop has started overheating -- how hot is hot?

  - by Jerry

  I have a two year old desktop, some random quad core HP desktop. It used to run very quietly, but in the past month, the fans start up anytime anything "serious" is being done -- compiles, playing video, etc. Right now, speedfan and speccy report the cores are between 50C and 70C. Speedfan reports this as hot. (Nice flame icon.) Well, the system does sit on my carpet, so two weeks ago, I took off the lid, and cough *cough* it was pretty filled with dust. I got out an air can, turned on a vacuum and carefully got out all the dust that I saw on the CPU fan the case fans any fan I saw (graphics board) and blew out all the dust I could from all the circuit boards. And then I closed the case back up. It has definitely run cooler since then, but it still runs hot, and I hear high speed fan noise I never heard before. How hot is too hot? At what temps do consumer grade CPUs die? What should I be looking to do? Replace CPU fan? (It seems to work) Replace power supply fan? Assuming the dust problem is gone, where should I be looking to determine why the machine is heating up? Epilogue: After following the various pieces of advice given here, the system did run cooler, but it was still noticeably running louder (hotter) than just a few months prior. I ended up purchasing a new cpu heatsink and fan and during installation found the cooling grease from the original heatsink was just a dried, cracked layer, probably more of an insulator than heat transfer agent. With the new fan AND the new heatsink compound, the system ran much much cooler and the fan rarely turns on.

  Read the article

• dd oflag=direct 5x fast

  - by César

  I have Centos 6.2 in server with this specs: 2xCPU 16 Core AMD Opteron 6282 SE 64GB RAM Raid controller H700 1GB cache NV - 2HD 74GB SAS 15Krpm RAID1 stripe 16k (OS Centos 6.2) sda - 4HD 146GB SAS 15Krpm RAID10 stripe 16k (ext4 bs 4096, no barriers) sdb -> /vol01 Raid controller H800 1GB cache nv - MD1200 12HD 300GB SAS 15Krpm RAID10 stripe 256k (For DB Postgres 8.3.18) (ext4 bs 4096, stride 64, stripe-width 384, no barriers) sdc -> /vol02 I'm benchmarking IO speed with dd, and view thah if in RAID10 12 disk exec: dd if=/dev/zero of=DD bs=8M count=10000 oflag=direct 10000+0 records in 10000+0 records out 83886080000 bytes (84 GB) copied, 126,03 s, 666 MB/s but if I remove "oflag=direct" option obtain about 80 MB/s. In read benchmark, results are similar: dd of=/dev/null if=DD bs=8M count=10000 iflag=direct 10000+0 records in 10000+0 records out 83886080000 bytes (84 GB) copied, 79,5918 s, 1,1 GB/s If remove iflag=direct obtain 150MB/s... I don't understand this huge differences, on other machines y don't have this behavior. Can I have some kernel parameter misconfigured? Thanks!

  Read the article

• Firefox 29 - how do I delete history entries visited fewer than x times

  - by lousyuser

  Context: I've been using my Firefox profile for a couple of years now. My history file has become huge, naturally. I got Firefox Sync set up between my main desktop PC and my laptop. HW configs: PC: i5-3450, 8 GB DDR3 RAM, Crucial M4 128 GB SSD laptop: Pentium SU4100, 4 GB DDR3 RAM, WD 5400 rpm HDD Accessing history entries when typing into the Awesome Bar on my desktop takes quite a long time despite the decent config, the laptop is even slower. The experience is quite unresponsive. I figured if I cleared the history up a little bit, I might avoid creating a new profile to speed things up. The question itself: to illustrate: Is there a way to delete all history entries that have been visited fewer than x (let's say 5) times and at the same time the recent visit is fewer than y (let's say 120) days old? afaik the history file is some kind of SQL database, but I'm not really sure how the data is saved, if there's a "safe way" to edit it and what the query to do what I need would look like. Thanks in advance for any help. I kept browsing through previous SuperUser questions to see if I could find relevant information. "In my Firefox profile directory, there is a filed named places.sqlite. Opening it with sqlite reveals (amongst others) the tables moz_places and moz_historyvisits. It seems that moz_historyvisits uses the primary of moz_places to refer to the URLs." As I'm unfamiliar with databases, I don't really understand the way the two tables mentioned in the quote are related. screenshot of a part of the tables I've noticed the visit_count is in a standard format, making it easy to work with. The last_visit_date looks encrypted to my naked eye, but I can't see in which way. Hope that helps, I'm at my wits' end.

  Read the article

• warning: dict_ldap_lookup: Search error 1: Operations error

  - by drecute

  Please I need help with ldap search filter to use to retrieve the user email information from ldap. I'm running postfix_ldap of Ubuntu server 12.04. Everything seems to work fine, except getting the values returned from the search. Version 1 server_host = ldap://samba.example.com search_base = dc=company, dc=example, dc=com query_filter = mail=%s bind = no domain = example.com Version 2 server_host = ldap://samba.example.com search_base = dc=company, dc=example, dc=com query_filter = mail=%s bind_dn = cn=Users,dc=company,dc=example,dc=com domain = example.com mail logs Nov 26 11:13:26 mail postfix/smtpd[19662]: match_string: example.com ~? example.com Nov 26 11:13:26 mail postfix/smtpd[19662]: dict_ldap_lookup: No existing connection for LDAP source /etc/postfix/ldap-aliases.cf, reopening Nov 26 11:13:26 mail postfix/smtpd[19662]: dict_ldap_connect: Connecting to server ldap://samba.example.com Nov 26 11:13:26 mail postfix/smtpd[19662]: dict_ldap_connect: Actual Protocol version used is 3. Nov 26 11:13:26 mail postfix/smtpd[19662]: dict_ldap_connect: Binding to server ldap://samba.example.com with dn cn=Users,dc=company,dc=example,dc=com Nov 26 11:13:26 mail postfix/smtpd[19662]: warning: dict_ldap_connect: Unable to bind to server ldap://samba.example.com with dn cn=Users,dc=company,dc=example,dc=com: 49 (Invalid credentials) Nov 26 11:13:26 mail postfix/smtpd[19662]: warning: ldap:/etc/postfix/ldap-aliases.cf lookup error for "[email protected]" Nov 26 11:13:26 mail postfix/smtpd[19662]: maps_find: virtual_alias_maps: [email protected]: search aborted Nov 26 11:13:26 mail postfix/smtpd[19662]: mail_addr_find: [email protected] -> (try again) Nov 26 11:13:26 mail postfix/smtpd[19662]: NOQUEUE: reject: RCPT from col0-omc3-s2.col0.hotmail.com[65.55.34.140]: 451 4.3.0 <[email protected]>: Temporary lookup failure; from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<col0-omc3-s2.col0.hotmail.com> Nov 26 11:13:26 mail postfix/smtpd[19662]: > col0-omc3-s2.col0.hotmail.com[65.55.34.140]: 451 4.3.0 <[email protected]>: Temporary lookup failure here's another log with successful search result but fialed to get the values of the result Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: Using existing connection for LDAP source /etc/postfix/ldap-aliases.cf Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: /etc/postfix/ldap-aliases.cf: Searching with filter [email protected] Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_get_values[1]: Search found 1 match(es) Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_get_values[1]: Leaving dict_ldap_get_values Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: Search returned nothing Nov 26 12:04:56 mail postfix/smtpd[20463]: maps_find: virtual_alias_maps: [email protected]: not found Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: In dict_ldap_lookup Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: /etc/postfix/ldap-aliases.cf: Skipping lookup of key 'tola.akintola': domain mismatch Nov 26 12:04:56 mail postfix/smtpd[20463]: maps_find: virtual_alias_maps: tola.akintola: not found Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: In dict_ldap_lookup Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: /etc/postfix/ldap-aliases.cf: Skipping lookup of key '@example.com': domain mismatch Nov 26 12:04:56 mail postfix/smtpd[20463]: maps_find: virtual_alias_maps: @example.com: not found Nov 26 12:04:56 mail postfix/smtpd[20463]: mail_addr_find: [email protected] -> (not found) My refined ldap-aliases.cf looks like this: server_host = ldap://samba.example.com server_port = 3268 search_base = dc=company, dc=example, dc=com query_filter = mail=%s result_attribute = uid bind_dn = cn=Administrator,cn=Users,dc=company,dc=example,dc=com bind_pw = pass domain = example.com So I'll like to know what ldap filter is appropriate to get this to work. Thanks for helping out.

  Read the article

• How to backup a NAS drive to a USB drive?

  - by Tim Murphy

  How would you backup 600+ GB of data on a NAS (Network-Attached Storage) drive to a USB external drive? The NAS drive does not contain mission critical data nonetheless I wish to make weekly copies of it just in case. The NAS drive is almost exclusively used as an archive dump and is rarely updated. However the backup strategy used must have a simple restore procedure so I can confidently say the data now on the NAS drive is exactly how it was at the time of backup. I did try xcopy but seemed like it would take many-many hours and eventually crashed with insufficient memory. http://www.ctunion.com/node/114 suggests I would need to use xxcopy instead due to folder/file name lengths. My concern with xcopy/xxcopy is the length of time it takes. Hoping something else is faster. NAS drive is DLink DNS-313. 1TB drive installed. Connected to router via Ethernet cable. USB drive is Seagate 1TB. Can be connected to Windows Vista (preferred) or Windows 7 PCs. Both PCs are usually connected Wirelessly however ethernet cable can be used during backup to speed up the process.

  Read the article

• Samba with remote LDAP authentication doesn`t see users properly

  - by LucasBr

  I'm trying to setup a samba server authenticated by a remote LDAP server, and I'm having some problems that I can't figure how to solve. I was able to make an getent passwd at samba server and I could see all users at ldapserver, but when I tried to access \\SAMBASERVER at my windows box I had this at the /var/log/samba/log.mywindowsbox: <...snip...> [2012/10/19 13:05:22.449684, 2] smbd/sesssetup.c:1413(setup_new_vc_session) setup_new_vc_session: New VC == 0, if NT4.x compatible we would close all old resources. [2012/10/19 13:05:22.449692, 3] smbd/sesssetup.c:1212(reply_sesssetup_and_X_spnego) Doing spnego session setup [2012/10/19 13:05:22.449701, 3] smbd/sesssetup.c:1254(reply_sesssetup_and_X_spnego) NativeOS=[] NativeLanMan=[] PrimaryDomain=[] [2012/10/19 13:05:22.449717, 3] libsmb/ntlmssp.c:747(ntlmssp_server_auth) Got user=[lucas] domain=[BUSINESS] workstation=[MYWINDOWSBOX] len1=24 len2=24 [2012/10/19 13:05:22.449747, 3] auth/auth.c:216(check_ntlm_password) check_ntlm_password: Checking password for unmapped user [BUSINESS]\[lucas]@[MYWINDOWSBOX] with the new password interface [2012/10/19 13:05:22.449759, 3] auth/auth.c:219(check_ntlm_password) check_ntlm_password: mapped user is: [SAMBASERVER]\[lucas]@[MYWINDOWSBOX] [2012/10/19 13:05:22.449773, 3] smbd/sec_ctx.c:210(push_sec_ctx) push_sec_ctx(0, 0) : sec_ctx_stack_ndx = 1 [2012/10/19 13:05:22.449783, 3] smbd/uid.c:429(push_conn_ctx) push_conn_ctx(0) : conn_ctx_stack_ndx = 0 [2012/10/19 13:05:22.449791, 3] smbd/sec_ctx.c:310(set_sec_ctx) setting sec ctx (0, 0) - sec_ctx_stack_ndx = 1 [2012/10/19 13:05:22.449922, 2] lib/smbldap.c:950(smbldap_open_connection) smbldap_open_connection: connection opened [2012/10/19 13:05:23.001517, 3] lib/smbldap.c:1166(smbldap_connect_system) ldap_connect_system: successful connection to the LDAP server [2012/10/19 13:05:23.007713, 3] smbd/sec_ctx.c:418(pop_sec_ctx) pop_sec_ctx (0, 0) - sec_ctx_stack_ndx = 0 [2012/10/19 13:05:23.007733, 3] auth/auth_sam.c:399(check_sam_security) check_sam_security: Couldn't find user 'lucas' in passdb. [2012/10/19 13:05:23.007743, 2] auth/auth.c:314(check_ntlm_password) check_ntlm_password: Authentication for user [lucas] -> [lucas] FAILED with error NT_STATUS_NO_SUCH_USER [2012/10/19 13:05:23.007760, 3] smbd/error.c:80(error_packet_set) error packet at smbd/sesssetup.c(111) cmd=115 (SMBsesssetupX) NT_STATUS_LOGON_FAILURE [2012/10/19 13:05:23.010469, 3] smbd/process.c:1489(process_smb) Transaction 3 of length 142 (0 toread) <...snip...> /etc/samba/smb.conf file follows: [global] dos charset = 850 unix charset = LOCALE workgroup = BUSINESS netbios name = SAMBASERVER bind interfaces only = true interfaces = lo eth0 eth1 smb ports = 139 hosts deny = All hosts allow = 192.168.78. 192.168.255. 127.0.0.1 10.149.122. 192.168.0. name resolve order = wins bcast hosts log level = 3 syslog = 0 log file = /var/log/samba/log.%m max log size = 100000 domain logons = No wins support = Yes wins proxy = No client ntlmv2 auth = Yes lanman auth = Yes ntlm auth = Yes dns proxy = Yes time server = Yes security = user encrypt passwords = Yes obey pam restrictions = Yes ldap password sync = Yes unix password sync = Yes passdb backend = ldapsam:"ldap://192.168.78.206" ldap ssl = off ldap admin dn = uid=root,ou=Users,dc=business,dc=intranet ldap suffix = ldap group suffix = ou=Groups ldap user suffix = ou=Users ldap machine suffix = ou=Computers ldap idmap suffix = ou=Idmap ldap delete dn = Yes add user script = /usr/sbin/smbldap-useradd -m "%u" delete user script = /usr/sbin/smbldap-userdel "%u" add group script = /usr/sbin/smbldap-groupadd -p "%g" delete group script = /usr/sbin/smbldap-groupdel "%g" add user to group script = /usr/sbin/smbldap-groupmod -m "%u" "%g" delete user from group script = /usr/sbin/smbldap-groupmod -x "%u" "%g" set primary group script = /usr/sbin/smbldap-usermod -g "%g" "%u" add machine script = /usr/sbin/smbldap-useradd -W -t5 "%u" idmap backend = ldap:"ldap://192.168.78.206" idmap uid = 16777216-33554431 idmap gid = 16777216-33554431 load printers = No printcap name = /dev/null map acl inherit = Yes map untrusted to domain = Yes enable privileges = Yes veto files = /lost+found/ /publicftp/ So, \\SAMBASERVER says he couldn't find my user, but I can see it by getent passwd . What I can do in order to SAMBASERVER see and authenticate my user? Thanks in advance!

  Read the article

• Samba PDC share slow with LDAP backend

  - by hmart

  The scenario I have a SUSE SLES 11.1 SP1 machine as Samba master PDC with LDAP backend. In one share there are Database files for a Client-Server application. I log XP and Windows 7 machines to the local domain (example.local), the login is a little slow but works. In the client computers have an executable which opens, reads and writes the database files from the server share. The Problem When running Samba with LDAP password backend the client application runs VERY SLOW with a maximum transfer rate of 2500 MBit per second. If disable LDAP the client app speed increases 20x, with transfer rate of 50Mbit/sec and running smoothly. I'm doing test with just two users and two machines, so concurrency, or LDAP size shouldn't be the problem here. The suspect LDAP, Smb.conf [global] section configuration. The Question What can I do? I've googled a lot, but still have no answer. Slow smb.conf WITH LDAP [global] workgroup = zmartsoft.local passdb backend = ldapsam:ldap://127.0.0.1 printing = cups printcap name = cups printcap cache time = 750 cups options = raw map to guest = Bad User logon path = \\%L\profiles\.msprofile logon home = \\%L\%U\.9xprofile logon drive = P: usershare allow guests = Yes add machine script = /usr/sbin/useradd -c Machine -d /var/lib/nobody -s /bin/false %m$ domain logons = Yes domain master = Yes local master = Yes netbios name = server os level = 65 preferred master = Yes security = user wins support = Yes idmap backend = ldap:ldap://127.0.0.1 ldap admin dn = cn=Administrator,dc=zmartsoft,dc=local ldap group suffix = ou=Groups ldap idmap suffix = ou=Idmap ldap machine suffix = ou=Machines ldap passwd sync = Yes ldap ssl = Off ldap suffix = dc=zmartsoft,dc=local ldap user suffix = ou=Users

  Read the article

• Optimal file system type and mount options for an rsnapshot dedicated drive

  - by Nimmy Lebby

  We have an external USB 2 drive that we are using as a backup drive for our configuration. We use rsnapshot for the backups. It uses a few standard commands for managing snapshots: rm -rf: deletes expired snapshots mv: moves older snapshots down a slot cp -al: duplicates last snapshot to new slot rsync -a --delete --numeric-ids --relative: synchronizes new snapshot As you could see by the log below, the majority of the time is spent on the rm -rf and the cp -al steps: [25/Dec/2010:14:00:02] rsnapshot hourly: started [25/Dec/2010:14:00:02] echo 21012 > /var/run/rsnapshot.pid [25/Dec/2010:14:00:02] rm -rf /mnt/extdrive/snapshots/hourly.5/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.4/ /mnt/extdrive/snapshots/hourly.5/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.3/ /mnt/extdrive/snapshots/hourly.4/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.2/ /mnt/extdrive/snapshots/hourly.3/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.1/ /mnt/extdrive/snapshots/hourly.2/ [25/Dec/2010:14:15:48] cp -al /mnt/extdrive/snapshots/hourly.0 /mnt/extdrive/snapshots/hourly.1 [25/Dec/2010:14:23:32] rsync -a --delete --numeric-ids --relative /etc /mnt/extdrive/snapshots/hourly.0/sm4/ [25/Dec/2010:14:23:52] touch /mnt/extdrive/snapshots/hourly.0/ [25/Dec/2010:14:23:52] rm -f /var/run/rsnapshot.pid [25/Dec/2010:14:23:52] rsnapshot hourly: completed successfully My questions: I'm currently using ext4 for the filesystem. Maybe this is not the best choice from those available in Red Hat. Anyone have any recommendations that would speed up the process? The partition's mount options are sync,dirsync 1 2. Is there a way to optimize this since it's solely used for rsnapshot? Of course, reasoning would be greatly appreciated.

  Read the article

• One Comcast Business Gateway, One Router, Two Web Servers

  - by Kevin Scheidt

  I have a Comcast business account with a router and a web server (info) attached. behind the router there are multiple computers and a second web server (info) which also serves as a file server. (info) has two nics in it. One direct to comcast and one connected to the router. It needs to serve the world it's websites. It needs however, to also be able to see all the internal computers and (com)'s served files. With just 1 nic (the one connected to the router, not comcast), (info) works fine but no one outside can see it. (com) services port 80 and (info) needs to handle port 80 as well. I have two domain names registered, and 5 static ip's from comcast. right now h t t p: / /www.graceamazing.com handled by (com) works fine and h t t p: / /www.graceamazing.com:1307 handled by (info) works fine. but as soon as I enable the 2nd nic in (info) h t t p: / /www.graceamazing.info runs extremely slow (Horribly slow). however, h t t p: / /www.graceamazing.com:1307 and .com work fine. (com) has an ip address via the router 70.89.233.41 (info) has a ip addy of 70.89.233.46 via comcast (2nd nic) and a internal ip of 192.168.x.100 via static behind the router. Any suggestions or changes to make that will make h t t p: / /www.graceamazing.info perform with the same speed it has when going through h t t p: / /graceamazing.com:1307 is there a setting I should check / could have misssed?

  Read the article

• FreeBSD with Vagrant - don't know how to check guest additions version

  - by joelmaranhao

  On Mac OS X 10.9.3 Picked a box from the VagrantCloud Init the vagrant box $ vagrant init chef/freebsd-9.2-i386 A `Vagrantfile` has been placed in this directory. You are now ready to `vagrant up` your first virtual environment! Please read the comments in the Vagrantfile as well as documentation on `vagrantup.com` for more information on using Vagrant. List the files $ ls -al -rw-r--r-- 1 joel staff 4831 Jun 5 17:17 Vagrantfile Vagrantfile content VAGRANTFILE_API_VERSION = "2" Vagrant.configure(VAGRANTFILE_API_VERSION) do |config| config.vm.box = "chef/freebsd-9.2-i386" end Starting my virtual box leads to Errors $ vagrant up Bringing machine 'default' up with 'virtualbox' provider... ==> default: Box 'chef/freebsd-9.2-i386' could not be found. Attempting to find and install... default: Box Provider: virtualbox default: Box Version: >= 0 ==> default: Loading metadata for box 'chef/freebsd-9.2-i386' default: URL: https://vagrantcloud.com/chef/freebsd-9.2-i386 ==> default: Adding box 'chef/freebsd-9.2-i386' (v1.0.0) for provider: virtualbox default: Downloading: https://vagrantcloud.com/chef/freebsd-9.2-i386/version/1/provider/virtualbox.box ==> default: Successfully added box 'chef/freebsd-9.2-i386' (v1.0.0) for 'virtualbox'! ==> default: Importing base box 'chef/freebsd-9.2-i386'... ==> default: Matching MAC address for NAT networking... ==> default: Checking if box 'chef/freebsd-9.2-i386' is up to date... ==> default: Setting the name of the VM: freebsd92-i386_default_1401982167145_49633 ==> default: Fixed port collision for 22 => 2222. Now on port 2201. ==> default: Clearing any previously set network interfaces... ==> default: Preparing network interfaces based on configuration... default: Adapter 1: nat ==> default: Forwarding ports... default: 22 => 2201 (adapter 1) ==> default: Booting VM... ==> default: Waiting for machine to boot. This may take a few minutes... default: SSH address: 127.0.0.1:2201 default: SSH username: vagrant default: SSH auth method: private key default: Warning: Connection timeout. Retrying... default: Warning: Connection timeout. Retrying... ==> default: Machine booted and ready! Sorry, don't know how to check guest version of Virtualbox Guest Additions on this platform. Stopping installation. ==> default: Checking for guest additions in VM... default: The guest additions on this VM do not match the installed version of default: VirtualBox! In most cases this is fine, but in rare cases it can default: prevent things such as shared folders from working properly. If you see default: shared folder errors, please make sure the guest additions within the default: virtual machine match the version of VirtualBox you have installed on default: your host and reload your VM. default: default: Guest Additions Version: 4.2.16 default: VirtualBox Version: 4.3 ==> default: Mounting shared folders... default: /vagrant => /Users/joel/Code/anybots/operations/robot/freebsd92-i386 Vagrant attempted to execute the capability 'mount_virtualbox_shared_folder' on the detect guest OS 'freebsd', but the guest doesn't support that capability. This capability is required for your configuration of Vagrant. Please either reconfigure Vagrant to avoid this capability or fix the issue by creating the capability. Note that I have recently installed the latest version of VirtualBox, but somehow I can't find the Guest Additions.

  Read the article

• postfix: Temporary lookup failure for FQDN

  - by Thufir

  I'm using the FQDN of dur.bounceme.net which I want to resolve(?) to localhost. That is, I want mail to [email protected] to get delivered to user@localhost. I've tried following the Ubuntu guide on this and seem to be going in circles a bit. root@dur:~# root@dur:~# postfix stop postfix/postfix-script: stopping the Postfix mail system root@dur:~# postfix start postfix/postfix-script: starting the Postfix mail system root@dur:~# telnet dur.bounceme.net 25 Trying 127.0.1.1... telnet: Unable to connect to remote host: Connection refused root@dur:~# root@dur:~# telnet localhost 25 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 dur.bounceme.net ESMTP Postfix (Ubuntu) ehlo dur 250-dur.bounceme.net 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN mail from:[email protected] 250 2.1.0 Ok rcpt to:[email protected] 451 4.3.0 <[email protected]>: Temporary lookup failure rcpt to:thufir@localhost 451 4.3.0 <thufir@localhost>: Temporary lookup failure quit 221 2.0.0 Bye Connection closed by foreign host. root@dur:~# root@dur:~# grep telnet /var/log/mail.log Aug 28 00:24:45 dur postfix/smtpd[18256]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <thufir@localhost>: Temporary lookup failure; from=<[email protected]> to=<thufir@localhost> proto=ESMTP helo=<dur> Aug 28 00:24:58 dur postfix/smtpd[18256]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <[email protected]>: Temporary lookup failure; from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<dur> Aug 28 00:54:55 dur postfix/smtpd[18825]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <[email protected]>: Temporary lookup failure; from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<dur> Aug 28 00:55:08 dur postfix/smtpd[18825]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <thufir@localhost>: Temporary lookup failure; from=<[email protected]> to=<thufir@localhost> proto=ESMTP helo=<dur> root@dur:~# root@dur:~# postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/var/lib/mailman/data/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix default_transport = smtp home_mailbox = Maildir/ inet_interfaces = loopback-only mailbox_command = /usr/lib/dovecot/deliver -c /etc/dovecot/conf.d/01-mail-stack-delivery.conf -m "${EXTENSION}" mailbox_size_limit = 0 mailman_destination_recipient_limit = 1 mydestination = dur, dur.bounceme.net, localhost.bounceme.net, localhost myhostname = dur.bounceme.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 readme_directory = no recipient_delimiter = + relay_domains = lists.dur.bounceme.net relay_transport = relay relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_authenticated_header = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/dovecot-auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/ssl/certs/ssl-mail.pem smtpd_tls_key_file = /etc/ssl/private/ssl-mail.key smtpd_tls_mandatory_ciphers = medium smtpd_tls_mandatory_protocols = SSLv3, TLSv1 smtpd_tls_received_header = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport root@dur:~#

  Read the article

• Cannot get Windows snipping tool to auto run with AutoHotKey

  - by jasondavis

  I am trying to get Windows 7 sniping tool to run when I hit my PRINTSCREEN keyboard button with AUTOHOTKEY. I have been unsuccessful so far though. Here is what I have for the AutoHotKey script. I have tried this PRINTSCREEN::Run, c:\windows\system32\SnippingTool.exe and this PRINTSCREEN::Run, SnippingTool.exe and this PRINTSCREEN::Run, SnippingTool And all those give me this error when I hit the PRINTSCREEN button... It basicly says it cannot find the file, however the file path seems to be correct, I can copy paste it into a window and it opens the snipping tool, any ideas why it will not work? Here is the full code to my AHK file... ; ; AutoHotkey Version: 1.x ; Language: English ; Platform: Win7 ; Author: Jason Davis <friendproject@> ; ; Script Function: ; Template script (you can customize this template by editing "ShellNew\Template.ahk" in your Windows folder) ; #NoEnv ; Recommended for performance and compatibility with future AutoHotkey releases. SendMode Input ; Recommended for new scripts due to its superior speed and reliability. SetWorkingDir %A_ScriptDir% ; Ensures a consistent starting directory. /* PRINTSCREEN = Will run Windows 7 snipping tool */ PRINTSCREEN::Run, c:\windows\system32\SnippingTool.exe return

  Read the article

• Optimize shell and awk script

  - by bryan

  I am using a combination of a shell script, awk script and a find command to perform multiple text replacements in hundreds of files. The files sizes vary between a few hundred bytes and 20 kbytes. I am looking for a way to speed up this script. I am using cygwin. The shell script - #!/bin/bash if [ $# = 0 ]; then echo "Argument expected" exit 1 fi while [ $# -ge 1 ] do if [ ! -f $1 ]; then echo "No such file as $1" exit 1 fi awk -f ~/scripts/parse.awk $1 > ${1}.$$ if [ $? != 0 ]; then echo "Something went wrong with the script" rm ${1}.$$ exit 1 fi mv ${1}.$$ $1 shift done The awk script (simplified) - #! /usr/bin/awk -f /HHH.Web/{ if ( index($0,"Email") == 0) { sub(/HHH.Web/,"HHH.Web.Email"); } printf("%s\r\n",$0); next; } The command line find . -type f | xargs ~/scripts/run_parser.sh

  Read the article

• CUPS causes printer to click and doesn't print

  - by Pez Cuckow

  I'm suffering a strange problem with my Cannon iP4850 when trying to use CUPS on a Raspberry Pi (this is not RPi specific, please do not vote to move it). When I plug the printer into my Laptop (OSX) or my Desktop W7 it identifies as a iP4800 and prints perfectly. So I plug it into the Pi (running debian), set it up in CUPS enable sharing and can now see the iP4800 series shared on the network. However if I print to it (using AirPrint etc...); the file gets to CUPS safely (shows in the queue) but when it tries to print the printer clicks (like a loud thunk) 3/4 times and then gives in, with a double amber flashing light. In cups it shows as job completed. Do you know why using the pi and cups would cause what appears to be a hardware fault and what I can do to fix the problem or to provide further debug info? Thanks for your time! Description: Canon iP4800 series Location: Lounge Driver: Canon PIXMA iP4800 - CUPS+Gutenprint v5.2.9 (color, 2-sided printing) Connection: usb://Canon/iP4800%20series?serial=2239B2 Note: I've tried deleting and re-adding the printer to the Laptop, Desktop and PI and the results are always the same Log for plugging in printer and printing (attempting to) something until the printer turned off again pi@pezpi /var/log $ dmesg [ 7284.176336] usb 1-1.2: new high speed USB device number 8 using dwc_otg [ 7284.279703] usb 1-1.2: New USB device found, idVendor=04a9, idProduct=10d5 [ 7284.279750] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7284.279771] usb 1-1.2: Product: iP4800 series [ 7284.279786] usb 1-1.2: Manufacturer: Canon [ 7284.279800] usb 1-1.2: SerialNumber: 2239B2 Setting cups to verbose: Change loglevel in cupsd.conf to debug (or debug2) pi@pezpi /var/log $ sudo vim /etc/cups/cupsd.conf pi@pezpi /var/log $ sudo /etc/init.d/cups restart [ ok ] Restarting Common Unix Printing System: cupsd. pi@pezpi /var/log $ Log from $ /var/log/cups/error_log is at http://pastebin.com/7VZMRMrG (too large to post here) The log contains - in order (deleted the log and then did the beneath) Restarting the cups server Attempting to print a test page x2 Printing from 192.168.1.90 via AirPrint Printing from 192.168.1.90 via Network Print Turning the printer off and on again

  Read the article

• Different network response for indentical co-located machines

  - by Santosh

  We have a situation as follows: We have a two different virtual machines (VMs) on some remote server farm. The machines are identical in terms of hardware/software(OS) configurations. We have a J2EE application running on JBoss on each of those two machines. These two applications are of different version sav V1 on VM1 and V2 on VM2. We observed some degraded response time for application V2 when accessed via public URL. When we accessed the application through a secured VPN, there is hardly any difference. The bandwidth test (upload/download speed, ping etc) shows that VM1 is responding better when accessed via secured VPN. We concluded that the application does not seem to have performance issue. Because, it that's the case the performance degradation should also be there when access via VPN. So we concluded its the network problem. But since those two identical VMs are on same network we are looking for the reasons for different responses. My question is, given the above situation, what could be reasons for such a behavior ?

  Read the article

• Ubuntu 12.04 - HP ProLiant DL380 G4 - Load Maxes Out / Unresponsive

  - by Brian S

  Trying to post this question on here. I've posted it on the Ubuntu forums as well with no replies. Recently I upgraded an HP ProLiant DL380 G4 server from Ubuntu 10.04 server to Ubuntu 12.04 server. Upon doing so, the server will not - at random times - get to a load of 400+ and then become completely non-responsive. I use an SNMP graphing program (cacti) and the load steadily increases by about 10 every five minutes until it gets over 400 and the graphing stops. The graphs may not be accurate, but the CPU load averages about 3% before this happens - and right when the load starts increasing, it jumps to about 25% for 15 minutes and dramatically dips down to less than 1% (about 0.3%) until the graphing stops. I'm not able to open a SSH tunnel to the server to do anything. I've checked the /var/log/syslog and all logging stops at that time as well - with nothing else in there. The odd thing is - the server still responds to DNS queries for the zones it is authoritative on during this time - and at normal speed. Just not sure what the next step would be in order to find out what is going on - and how this issue can be corrected. The server cannot stay with Ubuntu 10.04 Server and needs to stay upgraded.

  Read the article

• What is the quickest reliable way to backup a NAS drive to a USB drive?

  - by Tim Murphy

  How would you backup 600+ GB of data on a NAS (Network-Attached Storage) drive to a USB external drive? The NAS drive does not contain mission critical data nonetheless I wish to make weekly copies of it just in case. The NAS drive is almost exclusively used as an archive dump and is rarely updated. However the backup strategy used must have a simple restore procedure so I can confidently say the data now on the NAS drive is exactly how it was at the time of backup. I did try xcopy but seemed like it would take many-many hours and eventually crashed with insufficient memory. http://www.ctunion.com/node/114 suggests I would need to use xxcopy instead due to folder/file name lengths. My concern with xcopy/xxcopy is the length of time it takes. Hoping something else is faster. NAS drive is DLink DNS-313. 1TB drive installed. Connected to router via Ethernet cable. USB drive is Seagate 1TB. Can be connected to Windows Vista (preferred) or Windows 7 PCs. Both PCs are usually connected Wirelessly however ethernet cable can be used during backup to speed up the process.

  Read the article

• CPU-adaptive compression

  - by liori

  Hello, Let assume I need to send some data from one computer to another, over a pretty fast network... for example standard 100Mbit connection (~10MB/s). My disk drives are standard HDD, so their speed is somewhere between 30MB/s and 100MB/s. So I guess that compressing the data on the fly could help. But... I don't want to be limited by CPU. If I choose an algorithm that is intensive on CPU, the transfer will actually go slower than without compression. This is difficult with compressors like GZIP and BZIP2 because you usually set the compression strength once for the whole transfer, and my data streams are sometimes easy, sometimes hard to compress--this makes the process suboptimal because sometimes I do not use full CPU, and sometimes the bandwidth is underutilized. Is there a compression program that would adapt to current CPU/bandwidth and hit the sweet spot so that the transfer will be optimal? Ideally for Linux, but I am still curious about all solutions. I'd love to see something compatible with GZIP/BZIP2 decompressors, but this is not necessary. So I'd like to optimize total transfer time, not simply amount of bytes to send. Also I don't need real time decompression... real time compression is enough. The destination host can process the data later in its spare time. I know this doesn't change much (compression is usually much more CPU-intensive than decompression), but if there's a solution that could use this fact, all the better. Each time I am transferring different data, and I really want to make these one-time transfers as quick as possible. So I won't benefit from getting multiple transfers faster due to stronger compression. Thanks,

  Read the article

• Serving and caching content from Amazon S3 with Tomcat

  - by Rob

  Hi all, We're looking to serve a range of content using Amazon S3 as a store for the content and Tomcat to host the web application. The content is divided into free and paid for content. We intend to authenticate the users when they access the web application running in Tomcat. Based around their authentication we are able to tell if the user has access to paid for content or simply free stuff. So I envision the flow of a request being something like this: Authenticated request to Tomcat If user is "paid" user, display links to premium content Direct requests for paid content back through Tomcat to prevent direct access to it by non-paying users. Tomcat makes request to S3 through a web cache to keep our costs down Content is returned to user. As we have to pay for each request to S3, I'd ideally like to cache content locally to the Tomcat instance after it has been requested for the first time to keep costs to a minimum and to speed things up. I would also like to be able to invalidate this cache if we publish fresh content to S3. So to confirm my proposal: Client Request - Tomcat - Web Cache - S3 To invalidate the cache, I was thinking of using something like PubSubHubbub with the cache waiting for updates to the feed for content that it should invalidate. I'd appreciate some general feedback on this approach as I've no real experience of caching and I'm sure I've made some invalid assumptions. I'd also appreciate any recommendations for caching technologies. Thanks.

  Read the article

• Is StoreJet Transcend (0x2329) an Advanced Format drive?

  - by Graham Perrin

  I use a 640 GB StoreJet Transcend (0x2329) with ZEVO Community Edition 1.1.1 on OS X 10.8.2. Question Is this drive Advanced Format? Background I submitted a request for technical support to Transcend but the first response was gibberish so I don't expect a reasonable follow-up. Models at http://www.transcend-info.com/Products/CatList.asp?LangNo=0&ModNo=293 are similar but different sizes (not 640 GB). Mine is probably 25M2 (TS640GSJ25M2): Unless I'm missing something, nothing currently in the Transcend support area tells me whether the drive is Advanced Format. From System Information in OS X 10.8.2: StoreJet Transcend: Capacity: 640.14 GB (640,135,028,736 bytes) Removable Media: Yes Detachable Drive: Yes BSD Name: disk3 Product ID: 0x2329 Vendor ID: 0x152d (JMicron Technology Corp.) Version: 0.00 Serial Number: 322549FBA004 Speed: Up to 480 Mb/sec Manufacturer: JMicron History for the ZFS pool shows creation in March 2012 –  macbookpro08-centrim:~ gjp22$ zpool history zhandy | grep create 2012-03-14.17:29:37 zpool create -f -O compression=off -O copies=1 -O casesensitivity=insensitive -O snapdir=visible zhandy /dev/dsk/GPTE_1928482A-7FE4-482D-B692-3EC6B03159BA 2012-06-22.15:51:16 zfs create zhandy/Pocket Time Machine At that time I almost certainly used ZEVO Setup Assistant to create the pool. macbookpro08-centrim:~ gjp22$ zpool get ashift zhandy NAME PROPERTY VALUE SOURCE zhandy ashift 0 default If I discover that the drive is Advanced Format, a different ashift value will be appropriate.

  Read the article

• Poor SSL performance with vsftpd

  - by petrus

  I'm trying to tweak vsftpd to achieve maximum performance for my usage: I have only one or two clients that connect to the server. File size is between ~15MB and 1GB. Typical transfer batch represent between 1 and 2GB of data. For testing purposes, I'm using a tmpfs on both sides (thus eliminating any disks bottleneck) with a single 1GB file. When SSL is disabled, performance is good, with a transfer rate at ~120MB/s (reaching the limits of gigabit networking). With SSL enabled only for control traffic (and not data traffic), performance drops at about 112MB/s, which is still within the acceptable limits. However, when SSL is enabled for data flows, the transfer speed drops dramatically: 6.7MB/s using 3DES & SHA (ssl_ciphers=DES-CBC3-SHA in vsftpd.conf) 16MB/s using DES & SHA (ssl_ciphers=DES-CBC-SHA) I didn't tested other ciphers, but from what I can see from the CPU usage during the transfer, it seems that vsftpd is only using a single cpu/core per client. While this can fit for large ftp sites with hundreds of clients, I'd like to avoid this behavior and use more ressources on the server. On a side note, if you have any ideas regarding other openssl ciphers...

  Read the article

• Why are my socks proxies slow

  - by vps_newcomer

  I have a linux vps, and i have tried a few socks proxy setups to test their performance: All tests were using speedtest.net The standard ssh tunnel proxy 0.8mbit/s download and 0.1-0.2mbit/s upload speeds dante-server proxy 1.3mbit/s download and 0.4-0.5mbit/s upload I am wondering why are these speeds so slow? Is anything shaping them? Is it just the nature of socks proxies? I know that the ssh tunnel has to do encryption and what not so that is why its slow, but i was surprised to see that the second setup was also quite slow. On the VPS i have received download speeds of 25MB/s per second (thats about 200mbit/s and upload speed of atleast 5MB/s (haven't got a good enough pipe to test anything faster). The other option i was going to try is to setup OpenVPN and see how that goes, however i need to find a good tutorial as it's fairly complicated to setup. So why is it so slow? How can i test to see where the bottleneck is? How can i make it faster :D

  Read the article

• Multiple IP's using one NIC connectivity problem - Windows

  - by Vincent

  I have a frame relay network that is directly connected to a GPRS network. I also have a ADSL high speed network and recently I have been trying to achieve the following network configuration using windows 7 (Also tried XP) with no success to date. On one server I have two NIC's NIC1 I would like the following two static IP address's 10.0.1.110 and 10.0.1.200 the cisco router has a default gateway of 10.0.1.1 the ADSL is DHCP. NIC1 and the cisco router do not have access to the internet. NIC2 is setup for DHCP with a primary DNS and secondary DNS configured to enable internet connectivity. With NIC1 all incoming TCP connections are from IP address's starting with 10.192.x.x I cannot establish a TCP connection to both 10.0.1.110 and 10.0.1.200. Its either one or the other. I have a static route implemented in windows of: route -p 10.192.0.0 mask 255.255.0.0 10.0.1.1 metric 1 I have tried leaving out the gateway in the NIC1 and many other combinations with no success. Can anyone please help? What am I doing wrong?

  Read the article

• 5GHz vs 2.4GHz dual band router, max mbps

  - by Tallboy

  I've done a fair amount of reading before posting this but there are a few things still unclear. I just bought a Netgear WNDR3700 N600. I understand that 5GHz offers more channels, less interference because of more available channels, wont interfere with a microwave and so on, and also has a shorter range. Currently, my router is broadcasting both signals (for my iPhone on 2.4, and my computer on 5) But my question is What is the max speed of 5GHz in mbps? In the router settings, it allows me to set '300mbps', but I keep reading online that the max is 54. Is this true? I noticed when I set up the router the default for 2.4 was set to 300 and the default for 5 was set to 54, so I changed both to 300. Is this fine as well? I don't see why it wouldn't be maxed out for both by default. On the box it says max rate of 300+300 so I assume this is correct, but it's throttled down so the router isn't stressing in case you have something streaming media 24/7 and slowing the internet down too. What is the max range of 5GHz? my apt is 780 square feet, and the router is in the main living room.

  Read the article

< Previous Page | 556 557 558 559 560 561 562 563 564 565 566 567  | Next Page >