Search Results

Search found 2370 results on 95 pages for 'av cable'.

Page 57/95 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• Is this a common/bug on this PPPoE setting for Cisco ASA 5505?

  - by DCAlliances

  We have to change the way the firewall setup due to we've changed the internet provider. The way we setup we have ADSL modem and we have to do a full bridge mode and the firewall configuration has to change from Static IP to Use PPPoE option on Outside interface with PPPoE username and password, CHAP authentication, WAN IP and WAN subnet mask. [See the attachment] It's been working ok with the use of PPPoE option however the issue is that if we un-plug the power cable of the firewall. This "Outside" interface turned to blank - NO WAN IP, PPPoE username and password. So basically, we have to retype this information again. Is this common or a bug? Any ideas? Thanks

  Read the article

• Why only the left speakers are working?

  - by user324469

  I've just bought a 5.1 speakers and only the left side speakers and the center are working. If I plug in the speakers to my mp3 player than each speaker is working, so the speakers are good. I have windows 7 and I can't configure it. Please help me! I'm sure that the problem is with some settings at the computer. A while ago I had the same issue with some stereo speakers and I can't remember how I've fixed it, but it was only a setting error. I don`t think that my sound card could be the problem, because it's in-built and I have a new motherboard: asus m2n68-am. I've just tested my computer with some stereo head speakers and also only the left one was working. If I start the speakers very loud than the right speakers are making some noise, too I've connected the speakers with a two channels cable. This is the speakers type: genius sw-hf 5.1 5050 v2

  Read the article

• How can I get data off of a Corsair SSD?

  - by user1870398

  My Corsair SSD won't work and I have some critical data on it that I didn't back up (I needed to create a copy of my mechanical storage device, just forgot). The drive isn't detected by the OS or BIOS. I also tried it on another system, but all that happened was the OS failed to load (my guess was that it knew the drive was there, just couldn't read it). I tried powering it on without the data cable for a bit of time to see if it'd work again, but it didn't. Any ideas of how I can get the data off of this drive without having to send it in?

  Read the article

• Linksys WRT54G2 not showing connected PC's in DHCP table

  - by Moose

  For some reason all of a sudden my linksys WRT54G2 no longer shows PC's connected in the DHCP table. It was being touchy then all of a sudden they all just disappeared. It showed 2 of the 4 connected then it showed the other 2 then it only showed 1 and then it was showing none. I seem to be having a connection reset every 30-60 minutes also not sure if that is related to the router going bad or if it is just comcast being it's typical crappy self. I have tried to reset my router and my cable modem and both problems still seem to keep happening(no PC's in table and connection reset every 30-60 mins). Now I know the router doesn't store clients after a router reboot but they normally show up within a matter of minutes for me in the past. Before anyone asks yes all devices on the network are using DHCP and not static. Could this be a sign of the router starting to go bad?

  Read the article

• Windows 7 randomly installs an "Unknown Device" successfully

  - by Amazed

  Rarely (several days to weeks between occurrences,) and seemingly at random, I get a balloon notification from Windows 7 (x64 SP1 Home Premium) that it is installing hardware for me. Whatever is being installed does so without error. However, no new hardware has been installed or plugged in! When I click the balloon it doesn't give me any useful information: Looking in the event log, I find this entry: Event ID: 20001 Source: UserPnp Task Category: 7005 Message: Driver Management concluded the process to install driver FileRepository\usb.inf_amd64_neutral_153b489118ee37b8\usb.inf for Device Instance ID USB\VID_0000&PID_0000\6&3AF9A177&0&0060&&02 with the following status: 0x0. It appears to be USB related. My motherboard has both USB 2.0 and 3.0 controllers. My keyboard and mouse are plugged into the 2.0 slots and the data/recharge cable for a tablet (but not the tablet itself) was plugged in to the 3.0 slot. No other USB devices have been attached for several days/reboots. Why is Windows doing this?

  Read the article

• Should I remove all unmanged switches from my network?

  - by IMAbev

  I have a office network with approx 150 devices (computers/printers/ip phones). Almost all of the end point devices have straight run Cat5e from my Hp switches directly to the device. IP phones for each end user sit between the hp switch and computer. (hp switch - in to phone out of phone in to computer) While I have gotten rid of most of them, I still have a couple linksys unmanaged switches that split off to 2 or more devices. I have heard various reasons for removing these switches but not entirely sure if it actually degrades the network. I agree that eliminating these switches certainly cleans up the network from a management standpoint. Are these unmanaged switches bad for my network? Is there a clear advantage to having 'home run' cable runs to each of my end point devices?

  Read the article

• MySQL replication hung after slave goes offline and comes back online again

  - by Ed Manet

  I have a master server and several slave servers replicating a single database. I am using in MySQL 5.0 in SLES 11. During fault tolerance testing I found that when the slave's network connection is broken (cable un-plugged) and then restored, replication hangs. It shows no errors and the slave appears to be running but the Read_Master_Log_Pos and Exec_Master_Log_Pos values do not match the log postion on the master server. The Slave_IO_State is "Waiting for master to send event". The Slave_IO_Running and Slave_SQL_Running values are both are "Yes". The Master_Log_File and Relay_Master_Log_File match. If I stop and start the slave or restart the mysql daemon, replication starts working again. Any ideas on what I can do about this?

  Read the article

• Change audio output depending on which one is on

  - by pkrish

  I have a PC that is hooked up to my HDTV (via a long hdmi cable) and to a monitor, which is in another room. I have speakers directly plugged to the PC audio out. The PC is next to the monitor and speakers. I am not sure but I think Windows can play sound on only 1 audio device at a time. And I can only set 1 device as the default output. I can get sound on the TV or speaker depending on which device I set to default. But I would have to do this every time I switch between using my TV or my monitor! Is there some way to configure such that sound plays through the TV if the TV is on, else it plays in the speakers? If this is not possible, then the next best alternative would be to get the sound to play on both the devices at the same time. Thanks!

  Read the article

• Routing internet through ethernet to a computer without a Wireless adapter

  - by Decency

  I'm setting up a small home network. I have a laptop which connects to internet wirelessly- that works fine. I have a desktop connected to this laptop by an ethernet cable which I'd like to access the internet with. In the past, I have used a different laptop to do this and had no problems doing so. Both computers run Windows 7. I have tried setting up a homegroup and disabling Windows firewall, as well as restarting both computers. I can share data but my internet connection can not be accessed through the desktop. (I understand USB network adapters are cheap, I have one on the way but that doesn't solve this issue.) Any help or live chat support if you'd prefer would be appreciated. Thanks!

  Read the article

• Realtek HD Audio 5.1 Optical Input (from Xbox 360)

  - by Shevek

  I'm trying to connect up my Xbox 360 digital audio to my 5.1 speakers via my PC (my LCD has dual input, DVI for the PC, D-SUB for the Xbox). The motherboard has a Realtek ALC888 chipset and I have a 5.1 speaker system connected via 3 x 3.5mm jacks (FR/FL, RR/RL, C/LFE) and I get full 5.1 output from the PC. I have connected the optical audio cable from the Xbox to the Optical In on the motherboard's backplate. With the Xbox in Digital Stereo mode I get 2 channel audio from the Xbox, through the PC, to the speakers. With the Xbox in Dolby Digital 5.1 mode I get no sound at all. I have the latest Realtek drivers installed in Win 7 32-bit. Questions: Is it possible to use the full 5.1 DD from the Xbox? If so, am I missing some option(s) in the Realtek setup? Do I need some other piece of software to do this? (AC3Filter or FFDShow perhaps) Many thanks

  Read the article

• Stunnel delaying boot

  - by Onitlikesonic

  My stunnel implementation works fine when the network is plugged in but it takes an awful amount of time, which delays the whole boot process, when there is no network connected to the machine. As extra information: I'm using "delay=yes" I'm using an fqdn (e.g: stunnel.mydomain.com) for the connections Using ubuntu but this also happened with centos5 previously How can this be avoided or a timeout specified? edit: doing an strace as suggested by symcbean shows the following (including the last part where it hangs): [...] --- SIGCHLD (Child exited) @ 0 (0) --- rt_sigreturn(0x11) = 0 close(3) = 0 wait4(-1, [{WIFEXITED(s) && WEXITSTATUS(s) == 0}], 0, NULL) = 6039 clone(child_stack=0, flags=CLONE_CHILD_CLEARTID|CLONE_CHILD_SETTID|SIGCHLD, child_tidptr=0x7ff9ce0c79d0) = 6046 wait4(-1, [{WIFEXITED(s) && WEXITSTATUS(s) == 0}], 0, NULL) = 6046 --- SIGCHLD (Child exited) @ 0 (0) --- rt_sigreturn(0x11) = 6046 write(1, "[Started: /etc/stunnel/stunnel.c"..., 37) = 37 write(1, "stunnel.\n", 9) = 9 exit_group(0) = ? [...] stunnel hangs in this line: wait4(-1, and when i plug in the network cable it continues to show [{WIFEXITED(s) && WEXITSTATUS(s) == 0}], 0, NULL) = 6046

  Read the article

• How can I switch between the HDMI and DVI outputs of my graphics card?

  - by Owen Melbourne

  I've got an Nvidia GTX 560ti card which currently I've got my 2 monitors hooked up to using the 2 DVI ports. However its got a mini-HDMI port which I've plugged a HDMI cable in (with mini adapter) and lead it into my TV which is across the room. I'm hoping to be able to toggle between the HDMI output and the DVI outputs, however I'm not sure how I'd go about this, Could somebody please point me in the right direction, I'm not really worried about having all 3 on at the same time so that isn't a problem, but if its possible then I'll do that.

  Read the article

• How share internet connection between two laptops

  - by danielgratzz

  I have what appears to be a cable modem plugged into the wall with only ONE ethernet port on it. Therefore i can only connect one computer to it. Also, it has no wireless capability. I have to dialup the connection and enter a username and password on my laptop. But how can i share this internet connection between two laptops running windows 7 ultimate? I have spare ethernet cables if that would help... Please help, thank You.

  Read the article

• RDMA architecture - do you need adapters on both ends?

  - by Bobb

  I know Linux can use RDMA NICs like Solarflare... I just found Intel has something like that NetEffect cards. But Intel is talking all about clusters.. Can someone please explain. If I want low-latency networking and install RDMA NIC on my server. Is there limitation on where the cable can go? Is there a specific device expected on the other end? Is it special RDMA switch or RDMA adapter before switch or what? Why is this cluster talk? What if I want a single server with Windows (I can install HPC Windows or Windows 2008 R2)?

  Read the article

• How do I maximize and check my gigabit transfer rate?

  - by J Penguin

  I'm trying to maximize my LAN transfer speed. LAN cards and switch are all gigabit on a CAT 6 cable. Modes are set correctly to 1000 full duplex. CentOS server Testing with ftp from both windows and fedora, I'm only having the speed around 11MB/s. On windows I notice that the first few seconds of file transfer I'm actually getting around 25MB/s before it drops to 11MB/s Can anyone please recommend me what my next step should be to increase this performance? Are there any utilities I can use to test the file transfer speed without taking hard drive speed into consideration? The only thing I know is the MTU which I will have to wait until the office hour is over before I can play with it. If there are anything else I should be aware of, please please let me know. Thank you!

  Read the article

• Server only powers (but doesn't POST) when IDE drive is powered

  - by Jookia

  So after a thunderstorm last night which did a little damage, a Gigabyte server has decided it's going on power on but not POST. If it is POSTing, it's doing a very bad job at telling me. No beeps, nothing. Power seems to reach the components though. CD Drive opens and closes. So after stripping it back, I've found that the difference between this behaviour and deciding it's not going to power on for more than half a second, is having a power cable plugged in to one of the IDE hard drives. Is this normal, or a sign that the PSU has had it?

  Read the article

• "No bootable device - insert boot disk" after restart on Ubuntu 10.04 b1 update

  - by anjanesh

  I was making an update on my Ubuntu 10.04 beta1 64-bit PC when, after reboot I get PXE-E61: Mediaa test failure, check cable PXE-M0F: Exiting Intel Boot Agent. No bootable device - insert boot disk and press any key How did my boot record disappear ? BIOS Boot Boot Menu Type : Normal Boot Device Priority : <CD/DVD-ROM Drive> <Hard Disk Drive> <Floppy Drive> <Ethernet> Hard Driver Order : No Hard Disk Drive CD/DVD ROM Drive Order : <PT-TSSTcorp CDDV> Removable Drive Order : No Removable Drive Boot to Optical Devices : <Enable> Boot to Removable Devices : <Enable> Boot to Network : <Enable> USB Boot : <Enable>

  Read the article

• How do I increase my home's bandwidth?

  - by Derek

  I just mistakingly posted this on Stack Exchange but don't know how to delete it... Anyway, I was thinking of building a home server to use instead of renting a VPS, because in the long run it would be cheaper. What I'm concerned with is the bandwidth limit of my house. I know when I'm downloading something off the internet, if I download at high speeds the rest of the computers connected to my router will become slower. Is there any way to avoid this? There are other cable outlets in my house, will connecting a modem and router there avoid this problem?

  Read the article

• How do I set up failover for a single web server using two ISPs?

  - by Travis

  I have one web server and two WAN connections (1 cable, 1 DSL). DNS is run offsite, and points to the IP address assigned by one of the ISPs. How can I have the second connection take over when the primary one fails? I have seen that it is possible to have two A records, each pointing to a different IP, but it has several problems. What's the real solution to this? I imagine this is a very common issue. Thanks in advance!

  Read the article

• How to prevent Ubuntu from combining networks on 2 NIC server?

  - by SolarPower

  I've got a Ubuntu Server 10.10 with 2 network interfaces with a cable plugged into both going to switches on completely different networks with different routers. One network is the 10.1.10.X network with a separate gateway/router - the server has an IP of 10.1.10.50 with the gateway IP of 10.1.10.1. The other interface is 10.2.10.X, IP 10.2.10.50, gateway 10.2.10.1. All my Mac machines are on the 10.2.10.X network, and all servers on the 10.1.10.X. The ONLY connection between the two is this machine. From a Mac in my office, I CANNOT ping any computer on the 10.1.10.X network except the Ubuntu machine I'm talking about. However, under the Shared column in Finder, I can see every server on the other network listed. That makes me believe that somehow this Ubuntu machine is letting certain requests span both networks, which is a security problem. Hope this is enough info.

  Read the article

• Bitlocker-to-go on fixed drive

  - by Unsigned

  Scenario Two drives are connected to a computer. One via a SATA-to-USB interface, the other directly via a SATA-to-eSATA cable. The drive on USB appears as a removable drive, the drive on eSATA appears as a fixed drive. Both use NTFS. The USB drive offers Bitlocker-To-Go, the eSATA drive only offers BitLocker. Question It is my understanding that drives encrypted with BitLocker-To-Go include an app to allow Windows XP read-only access to the volume. Is this the only difference, and is there a way to use Bitlocker-To-Go on the eSATA drive? Update Another difference is found here: The recovery key is required when a BitLocker-protected fixed data drive configured for automatic unlocking is moved to another computer.[1] Assuming that does not apply to removable drives.

  Read the article

• GRUB Problem or Hardware Problem?

  - by Nikit Batale

  I have Windows XP Professional and Ubuntu Karmic Koala 9.10 on dual boot. I often get a GRUB loading failed error during boot-up. Or sometimes, when I try to boot into either Ubuntu or XP, I get a Could not read from source error. Now this is funny. After getting one of the above errors, if I simply unplug the SATA cable from Hard Drive end and plug it again, the problem gets solved. So what and whose problem is it? GRUB or My Hardware ? P.S.: I was suggested on StackOverflow that ServerFault is the right place for this question.

  Read the article

• an unknown ip on network

  - by Ahmed safan

  In our office we have many PCs, all of them have static IP addresses. We had a problem with one server with ip 192.168.1.10 dropping off the network occasionally. I unplugged the network cable from the server and from pinged 192.168.1.10 from another host and there was a response. I searched all PCs to see if any has such ip but i didn't found a one. I changed the server ip to fix the problem, but I still find this rogue device using 192.168.1.10 on the network -- how can I figure out what it is? Could it be the ip of virtual machine on someone's PC?

  Read the article

• Cannot see main user profile directory on old vista hdd on win7

  - by chaoskreator

  I have an old laptop HDD that ran Vista that I need to get some pictures and movies off of. I've attached it via SATA cable to my new Win 7 (64 bit) machine and it mounts fine, except I can't see the main user profile in the D:\Users directory. I've changed ownership and permissions for the D: drive to my C:\ Username but still no luck. I read something about it being caused by the UAC being active on the Vista machine. Is this true? Is there a way to disable this and gain access to the main profile without putting it back into the old laptop (it's fried and won't boot)?

  Read the article

• Configure TV Capture card to not use external audio jack for TV audio output

  - by Adam D.

  I had this working with MythTV on Ubuntu 9.1. Then a power surge killed the motherboard. After replacing the motherboard, ram and cpu, the card does not produce any audio except through the output jack on the back of the card. I do not want to use a cable to go from the back of the card to the audio in on the built in sound card of the new mother board. FYI, the old motherboard did not have an on-board sound card. There was a separate audio card installed. There's some configuration that has to be done to have it work the same way again. I just have no idea where to start. This is regarding wintv hauppauge mythtv linux ubuntu 9.10 audio

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >