Search Results

Search found 4765 results on 191 pages for 'wireless printers'.

Page 57/191 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• Network Manager kicks off abruptly

  - by Vijay Selvaraj

  I have installed Ubuntu 10.10 and trying to connect with my ADSL Wireless broadband internet modem using Linksys WUSB600N receiver. The good news is the OS is able to detect my wifi network and I am able to hook to network over WPA authentication with basic settings. But the network goes off abruptly and never connects again until I reboot the machine. I have Windows 7 as dual boot on my machine. The same adapter works perfectly with Windows 7 but not in Ubuntu. Is there anything in need to tweak to make things working or do I need to try any other better network manager on Ubuntu?

  Read the article

• Cannot connect to a Wifi network chipset AR9287

  - by Fritz

  After updating my newly installed ubuntu 10.10. I can't connect to the wifi network anymore although it is showing it. Tried to install manufacturer driver INF file via ndiswrapper only makes things worst - lost my wifi. Downloaded and installed the compat-wireless driver for the Atheros AR9287. After installing, i got my wifi connection again but after rebooting I can't reconnect again. The Wifi access point is showing 2/5 to 3/5 signal strength. Laptop: Acer Aspire 4741G Wifi Adapter: Atheros AR9287 OS: Ubuntu 10.10 64bit

  Read the article

• Acer Aspire One 722 broadcom 4313 wifi

  - by Colin Matheson

  I had an Acer Aspire One 722 with the Atheros Wifi card and it worked fine on 11.04. So we bought 200 of them for our school. However these all came with the Broadcom BCM4313 wireless card and there are issues. It is using the brcmsmac driver and they connect initially. However after a time (sometimes just a few webpages) some of them lose connection. However, they still have an IP and network-manager says they are connected, but no pages load and you can't ping anything on the LAN or internet. A disconnect/reconnect can fix it, but sometimes a restart is required. It happens frequently so is a major issue. Lots of broadcom drivers are blacklisted: bcm43xx, b43, brcm80211. Any ideas or experiences with the broadcom4313 card? Please save these computers from a Windows fate!

  Read the article

• WiFi and Bluetooth will not work on Dell Studio XPS 1645

  - by Ross

  Today I acquired a Dell XPS 1645. Ubuntu seems to run alright on it however The bluetooth is not detected and the WiFi doesn't work. The WiFi is especially weird because I actually have the restricted driver enabled for it. It also worked for a short while when I first booted into Ubuntu however now there isn't even an option to enable wireless. If anyone could possibly help me out with this I'd deeply appreciate it. I've not had to return to Windows for a good while and it's not something I want to have to do now.

  Read the article

• Unable to use TL-WN821N

  - by udiw

  Hi, I got a TP-LINK USB wireless module - TL-WN821N, using Ubuntu 10.4 (same problems were also seen in 10.10). From everything I've read online, the usb should work just fine, since the Atheros ar9170 is built into the kernel. However, when I plug it in, it is detected as a USB device, but there is no wlan associated with it, and basically - nothing happens. Am I doing something wrong? what should I do so that the Atheros driver is associated with this device? btw, on Windows it works fine (with the drivers). Some logs: $ uname -mr 2.6.32-28-generic i686 $ lsb_release -d Description: Ubuntu 10.04.2 LTS $ lsusb ... (trimmed) Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 017: ID 0cf3:7015 Atheros Communications, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub $ lsmod |grep ar9 ar9170usb 51296 0 ath 7611 1 ar9170usb mac80211 205402 3 ar9170usb,iwl3945,iwlcore cfg80211 126528 5 ar9170usb,ath,iwl3945,iwlcore,mac80211 led_class 2864 4 ar9170usb,iwl3945,iwlcore,sdhci

  Read the article

• Updated 11.10 - now trackpad and wifi won't work. How can these be fixed?

  - by Aron Standley

  I reinstalled 11.10 on my Asus EEE 1005HA, and my mousepad hasn't been working since. I've tried the workarounds mentioned in this post: http://ubuntuforums.org/showthread.php?t=1867357 but, I get the message on the command line that says, "Synaptic isn't installed." When I go to the network settings to install Synaptic, I can't turn on wifi - no wireless options exist. How can I turn on wifi from the command line, on a new 11.10 install? Or, is there a way to turn on the trackpad and wifi from the install thumb drive? How can I move forward?

  Read the article

• Need instructions how to create wpa_supplicant.conf and add fast_reauth=0 to it // WPA 2 Enterprise & frequent wlan disconnects

  - by nutty about natty

  Like many other natty users on a university / academic network, I'm experiencing annoying frequent disconnects / hangs / delays. See, for instance: https://bugs.launchpad.net/ubuntu/+source/wpasupplicant/+bug/429370 I would like to learn how to add fast_reauth=0 to the wpa_supplicant.conf file. This file, it seems, does not exit by default, and needs to be manually created first: http://w1.fi/gitweb/gitweb.cgi?p=hostap.git;a=blob_plain;f=wpa_supplicant/README [quote] You will need to make a configuration file, e.g., /etc/wpa_supplicant.conf, with network configuration for the networks you are going to use. [unquote] Further, I installed wpa_gui which probably needs to be launched with parameters, else it's pretty blank... What I'm hoping for is this: That creating a wpa_supplicant.conf file with fast_reauth=0 in it, saving it to the relevant path, will work and make my uni wireless (more or even completely) stable. I read mixed reviews about wicd (as an alternative to the network manager). Also note that on my basic wlan at home (with bog-standard wpa encryption) the connection is stable. Thanks!

  Read the article

• Install reliance Driver software in ubuntu 14.04

  - by A Umar Mukthar

  I'm Using Huawei ec 150 dongle. I need to install driver software It is quiet a big task for begineers in linux. So i took this matter over here. EDIT Output of lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 12d1:140b Huawei Technologies Co., Ltd. EC1260 Wireless Data Modem HSD USB Card Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 046d:c05a Logitech, Inc. M90/M100 Optical Mouse Bus 002 Device 002: ID 046d:c31d Logitech, Inc. Media Keyboard K200 Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

  Read the article

• Cannot connect to Open WiFi hotspot created by Android

  - by Bibhas

  I'm trying to share my 3G data connection via WiFi hotspot. I have an open Hotspot running on my phone(Xperia Neo V - MT11i - Android 2.3.4). But I cannot connect to it from my Ubuntu system. Here is the syslog while I try to connect to it - NetworkManager[1077]: <info> Activation (wlan0) starting connection 'TheNeo' NetworkManager[1077]: <info> (wlan0): device state change: disconnected -> prepare (reason 'none') [30 40 0] NetworkManager[1077]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled... NetworkManager[1077]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started... NetworkManager[1077]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled... NetworkManager[1077]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete. NetworkManager[1077]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting... NetworkManager[1077]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0] NetworkManager[1077]: <info> Activation (wlan0/wireless): connection 'TheNeo' requires no security. No secrets needed. NetworkManager[1077]: <info> Config: added 'ssid' value 'TheNeo' NetworkManager[1077]: <info> Config: added 'scan_ssid' value '1' NetworkManager[1077]: <info> Config: added 'key_mgmt' value 'NONE' NetworkManager[1077]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete. NetworkManager[1077]: <info> Config: set interface ap_scan to 1 NetworkManager[1077]: <info> (wlan0): supplicant interface state: inactive -> scanning wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) NetworkManager[1077]: <info> (wlan0): supplicant interface state: scanning -> authenticating kernel: [17498.113553] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17498.310138] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17498.510069] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17498.710083] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17504.779927] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17504.976420] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17505.176379] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17505.376314] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17511.478385] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17511.674738] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17511.874655] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17512.074659] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17518.152643] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17518.349064] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17518.549051] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17518.748999] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17524.858896] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17525.055404] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17525.255387] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17525.455254] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17531.589176] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17531.785747] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17531.985724] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17532.185610] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17538.329257] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17538.528003] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17538.728024] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17538.927922] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17545.022036] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17545.218339] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17545.418319] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17545.618206] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17551.724177] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17551.920685] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17552.120597] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17552.320526] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out NetworkManager[1077]: <warn> Activation (wlan0/wireless): association took too long, failing activation. NetworkManager[1077]: <info> (wlan0): device state change: config -> failed (reason 'supplicant-timeout') [50 120 11] NetworkManager[1077]: <warn> Activation (wlan0) failed for access point (TheNeo) NetworkManager[1077]: <warn> Activation (wlan0) failed. NetworkManager[1077]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] NetworkManager[1077]: <info> (wlan0): deactivating device (reason 'none') [0] NetworkManager[1077]: <info> (wlan0): supplicant interface state: authenticating -> disconnected NetworkManager[1077]: <warn> Couldn't disconnect supplicant interface: This interface is not connected. Why is direct probe to 5c:b5:24:2f:d1:2f timed out? Any idea?

  Read the article

• Connected to wifi, but quits loading pages after a random amount of time

  - by Collin

  I'm using Ubuntu 12.10, on a TOSHIBA Satellite L755 laptop, and using a Cradlepoint MBR-1000 wireless router. The wifi supposedly works fine on my sisters' and mom's laptops, and my dad uses a wired connection through the router. Nobody else has the problem. It shows that I'm connected and everything. The network manager GUI shows that everything is going just dandy... but it's not. I'll be able to load a page or two, then I have to disconnect, and reconnect to the router to get it to work again for a couple minutes. I noticed when I was downstairs, close to the router, this problem seemed to go away (at least, I was connected for a couple of hours without running into this problem). When I run ping -n 8.8.8.8 it shows this while the connection is still running fine 64 bytes from 8.8.8.8: icmp_req=1187 ttl=47 time=665 ms and whe

  Read the article

• E: unable to locate package firmware-b43-installer when i

  - by Raju

  I am using Acer aspire-5002wlmi laptop and set up a dual boot with Windows XP and Ubuntu 12.04. Wifi is well working in XP but when I start Ubuntu I will get the below error. [ 95.514855] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all the instruction on this website. then I followed the instructions from the below link file:///C:/Documents%20and%20Settings/MGL/Desktop/how%20to%20install%20ubuntu/Ubuntu%2012.04%20Splash%20Screen%20Lockup%20with%20LiveCD%20_%20Ben%20Rousch%27s%20Cluster%20of%20Bleep.htm but I am stuck in installing the Broadcom Wifi firmware in terminal and it is showing this error: E: unable to locate package firmware-b43-installer

  Read the article

• Wired connection stops working suddenly

  - by user90950

  I have Ubuntu 12.04.I was downloading something via aria..and then it suddenly stopped..no connection to Internet. I tried to ping the host but no reply..also tried to ping the route 192.168.250.1 but no reply got a message saying 'Ubuntu 12.04 has experienced internal error'. I restarted system but nothing is sorted out. The wired connection 'establishes' but I am not able to use Internet or ping either to host/route/8.8.8.8. The wireless is working fine and it does connect to Internet. I have a static IP address for wired connection and it does connect to Internet on Windows OS installed on this same Laptop with same IP settings.. please suggest how do i get my wired connection start working properly again..

  Read the article

• Wifi problem in ubuntu using macbook pro when it restart

  - by Amro

  I was read that subject : http://ubuntuforums.org/showthread.php?t=2011756 and i follow it step by step in the page n 1 , then i was connect but after i restart my macbook again , i was lost the wifi connection.i dont know why or whats the problem exactly. every time I run this command: dmesg | grep -e b43 -e bcma I get this output: [ 2012.769684] bcma-pci-bridge 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2012.769701] bcma-pci-bridge 0000:02:00.0: setting latency timer to 64 [ 2012.769775] bcma: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x25, class 0x0) [ 2012.769808] bcma: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1D, class 0x0) [ 2012.769889] bcma: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x13, class 0x0) [ 2012.770175] bcma: PMU resource config unknown for device 0x4331 [ 2012.824527] bcma: Bus registered [ 2012.831744] b43-phy0: Broadcom 4331 WLAN found (core revision 29) [ 2013.371031] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07) and to get the connection again every time i must entery that code in the step of reload driver. How i can let the ubuntu see my wifi and wireless device automatically when i reboot my computer????

  Read the article

• Wifi won't work without ethernet (Ubuntu 12.04)

  - by alok

  I have a strange problem. I am running Ubuntu 12.04 on a Dell Studio 1558 laptop. I'm usually unable to access Wifi (I have a BCM43224 wireless card with the STA proprietary driver installed.) So I have to unplug the ethernet cable from my Wifi router and stick it into my laptop's ethernet port to access the Internet. But when I stick the cable back into the Wifi router and try connecting to Wifi, Wifi inexplicably starts working. How can I get Wifi to work all the time without having to 'jumpstart' it with an ethernet connection?

  Read the article

• Two Wifi Icons in Panel

  - by Alex

  I have the exact problem in 13.10 as this user Two Wifi indicators in panel. Here are some screenshots: Here are some screenshots from another user: http://ubuntuforums.org/showthread.php?t=2183020&p=12825563 ifconfig and iwconfig outputs $ ifconfig lo Link encap:Local Loopback inet addr:XXXXXX Mask:XXXXXXX inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2243 errors:0 dropped:0 overruns:0 frame:0 TX packets:2243 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:209889 (209.8 KB) TX bytes:209889 (209.8 KB) wlan0 Link encap:Ethernet HWaddr XXXXXXXXX inet addr:XXXXXX Bcast:XXXXXXXX Mask:XXXXXXX inet6 addr: XXXXXXX Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5925 errors:0 dropped:0 overruns:0 frame:0 TX packets:3361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2951818 (2.9 MB) TX bytes:630579 (630.5 KB) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"XXXXX" Mode:Managed Frequency:2.437 GHz Access Point: XXXXXXXX Bit Rate=72.2 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:153 Invalid misc:472 Missed beacon:0

  Read the article

• Slow wifi after upgrading kubuntu 13.04 to 13.10

  - by RedCow22

  After upgrading from kubuntu 13.04 to 13.10 suddenly my wifi connection is very slow. Ping times are varying from 200 up to 1500 ms to www.google.nl. When I connect my ethernet cable they drop to normal times like 8 or 9 ms. Anyone experiencing the same problem or know a solution I can try? During the upgrade process a few times they asked whether I wanted to keep or replace some kind of configuration file. I'm not sure anymore which file it was, but maybe this has something to do with it. Before the upgrade both wired and wireless connection worked perfect.

  Read the article

• WINDOWS 7 DEAD BLUE SCREEN DOES NOT REBOOT OR INSTALL NEW WIN OS

  - by ADAM

  Windows died. So, I installed ubuntu, and have had difficulties downloading apps from the internet like skype or realplayer... etc. And It does not recognize my password. I needed to install drivers for my wireless from cd-rom. It does not show where to save new downloaded files and programs, and app and does not show how to install like windows does. So I would like to go back to windows. Window does not not start up anymore and I can not get safe mode with F8. It goes to black screen only and none of other parameters work when press f8! Any help is highly valued.

  Read the article

• System freeze after opening Wi-Fi menu can boot into the machine and use Internet in recovery mode

  - by Michael

  So right now sitting in front of my Alienware area 51 desktop. It has a Broadcom Netlink BCM 5784M gigabit ethernet PCI E card. Most of the time able to get through the login screen and to the main screen if I click on the wireless settings on the top right-hand corner the system immediately freezes the cursor does not move at all keyboards are unresponsive. I was doing some quick Google searching and I found a suggestion to boot into recovery mode I did this and did a apt-get Distribution update which ran successfully installed then I rebooted into the regular system same thing I'm pretty sure it's the network card because even if I don't click the settings if a network related dialog opens such as disconnection or connection the system again immediately freezes. I'm running Ubuntu 13.04 ** update 1 ** Just was able to use my system for a little bit however when I went into Firefox and hit the web it again froze so obviously a driver problem but I'm not sure how to get drivers for Broadcom which apparently according to the description on stack-overflow is terrible Any ideas? Sorry for lack of punctuation on an ipad.

  Read the article

• How do I get a D-Link DWL-G520 working?

  - by human33

  I have Ubuntu 12.04 on an older desktop PC, and I am finding it much harder to connect to a wifi connection than it should be. I have an iPhone with which I want to tether to it with Mifi 4.0, but I need to install ipheth which I can't do without internet on that computer. I am typing from my other windows pc with which i can download and move hings with thumb drives, but haven't gotten keryx to work. I also found a D-Link DWL-G520 HIGH SPEED 2.4GHZ (802.11G) WIRELESS 108MBPS PCI ADAPTER which I installed, but can't find a driver to put on a flashdrive to use it. If anybody has any ideas, they are appreciated. I am a noob, and I don't want to have to move the comp. downstairs to plug into the modem. PS: I also have a netgear USB network adapter, which doesn't work with my Ubuntu.

  Read the article

• Wifi USB interface being detected after some time

  - by Dani

  I've got a wifi interface connected by USB (its chipset is the zd1211b, which I think it works with the zyd driver). When I log into my ubuntu 12.04 it don't detect the inteface but after waiting an indeterminate amount of time (sometimes a few minutes, sometimes half an hour or more) it is detected and it works fine. It's just to weird and also very annoying because you don't know when are you going to be able to use the wireless connection. Any solution to this? Can I force somehow the SO to detect the interface?

  Read the article

• 3.5.0-18 kernel update broke BCM43228

  - by ignition

  After updating the kernel to 3.5.0-18 the Broadcom BCM43228 wireless card of my Acer Aspire One 756 has stopped working properly. The card often refuses to connect to my AP, and if it connects it behaves very unstable. I have already reinstalled the drivers, as recommended by googling around. As far as I can tell the only driver that supports my card is the bcmwl package. I found one solution saying I should install broadcom-sta using module assistant, however I could not get this to install and apparently broadcom-sta and bcmwl are effectively the same driver? Is anyone experiencing similar issues? Is it possible to just downgrade to the previous kernel version?

  Read the article

• Set up Trendnet TEW-638APB Access point on Ubuntu 14.04

  - by Mr. Smileys

  I have a computer running Ubuntu 14.04, it has 2 Ethernet ports. I would like to set up this computer so that the internet comes in on one of the ports and is then shared through the other port with the Trendnet wireless access point that my other devices would connect to and use the internet. I have looked online for information on setting this up but have not been able to find anything. If someone could point me to a guide that would help me or just tell me how to do this in an answer I would really appreciate it. please help me to solve this problem

  Read the article

• How to Install Linux on my PC

  - by Holic

  Hi i need some help to install the drivers from my pc, on Ubuntu 10.10 i just installed it, and i a newbie on Ubuntu, but i understand a bit of Windows...but i want to try ubuntu and then Maybe change to UBUNTU!!! My hardware: QuadCore Intel Core i7-870, 3266 MHz (24 x 136) Asus P7P55D-E (2 PCI, 3 PCI-E x1, 2 PCI-E x16, 4 DDR3 DIMM, Audio, Gigabit LAN, IEEE-1394) NVIDIA GeForce GTX 480 (1536 MB) nVIDIA HDMI @ nVIDIA GF100 - High Definition Audio Controller VIA VT1828S @ Intel Ibex Peak PCH - High Definition Audio Controller [B-3] DIMM1: G Skill F3-12800CL9-2GBRL 2 GB DDR3-1333 DDR3 SDRAM (8-8-8-22 @ 609 MHz) (7-7-7-20 @ 533 MHz) (6-6-6-17 @ 457 MHz) DIMM3: G Skill F3-12800CL9-2GBRL 2 GB DDR3-1333 DDR3 SDRAM (8-8-8-22 @ 609 MHz) (7-7-7-20 @ 533 MHz) (6-6-6-17 @ 457 MHz) my pc is not connected to the internet with a wire(RJ45) but with a wireless LAn Asus WL-167G-V3(wich i also whant to install if possible) Anything would've help me :) Cheers & Thank you!

  Read the article

• After running updates in 10.10 Netbook Remix, Ralink 5390 Not working

  - by nosound

  Additional Drivers still lists the driver. Reports it as being activated but not in use. Prior to running updates, wireless was working fine. Set it up using this guide: http://www.upubuntu.com/2012/02/how-to-install-drivers-for-ralink.html Thoughts and reflections would be much appreciated. ... nm. Using Synaptic Package Manager, marked for reinstallation, reinstalled, rebooted. Back to the way things were. Little new to this side of the world. ;)

  Read the article

• Ad-hoc network(hot spot created) not detected by android phone

  - by Nirmik

  I created a hot spot via network wireless use as hotspot. Other laptops successfully detected the hot-spot,could connect and use it without any problem. But no android phone could detect it.! I tried with many android phones but none could.(I found out that even an ad-hoc created in windows is not detected by any phone) So is there anything wrong i am doing(rather i am not doing anything actually other than clicking on the "use as hotspt" button..but still..)? or is that the network cannot be shared with phones? and if not,how can i share it with phones?

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >