Search Results

Search found 2048 results on 82 pages for 'x11 forwarding'.

Page 57/82 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• Wake on Lan/Wan won't work after some time has passsed

  - by Vian Esterhuizen

  I have the following set up: Gigabyte Z77X-UD5H Wake On Lan Enabled Asus N66U Port Forwarding Static IP assigned to my computer Windows 7 Advanced Power Management - PCI Express - Off Intel 82579V - All options under Power Management checked I'm trying to set this up for Wake on Wan capabilities. If I shut down my computer and immediately try to Wake on Wan (and Lan) it works and starts up. While the computer is on, I've used a few WOL specific packet sniffers and the packet comes through on the correct port. After any period of time over a few minutes, waking on Wan or Lan won't work. The back "activity" light is blinking on my ethernet port on my computer, as well as on the router, so I would assume the network card is on and able to receive a signal. Any ideas? Suggestions? What can I do to troubleshoot the problem?

  Read the article

• Changing linksys router configuration from command-line

  - by Dan

  I am constantly logged into (ssh'd) my home machine (ubuntu) from various remote locations. Sometimes I would like to change my home linksys router settings (change the port forwarding settings or disable/enable wireless, things like that). When I try and use the links2 text browser, there isn't much I can do because the tab titles don't show up (presumably because they are pictures?). Is there another way of configuring a linksys router from a command line? I guess my only other option is to set up a proxy on my home machine and use a browser connected to that proxy to configure it, but I would think there might be a non-browser way of doing it. Thanks

  Read the article

• How can I fix my Virtual PC 2007 network configuration

  - by DanJ

  Hi, I have installed Windows Virtual PC 2007 on my Windows 2003 R2 Server. I have installed a virtual Windows XP. I have configured the virtual PC to use Shared Networking (NAT) I have disabled the firewall on the virtual windows XP The problem: I am unable to PING from Windows 2003 (the host) to the Windows XP (virtual) I do have normal traffic from the virtual to the internet Could this problem be related to routing? How I can I fix this network configuration to allow for the following traffic: 1. From Virtual to Internet 2. From Host to Virtual 3. If possible, from Internet to Virtual on pre-defined ports (port forwarding?) Thanks

  Read the article

• How to configure squid for retrieving (and caching) directly my static resources?

  - by fabien7474

  I have an Apache/Tomcat/Spring tc Server running on CentOS EC2 VM. I would like to install squid on the same machine as a proxy for retrieving (directly i.e. without forwarding the request to Apache/Tomcat) and caching static content ONLY identified by URIs : /images, /css or /js. Other URIs should be forwarded to the normal Web Server and not cached. Since I am a newbie, I didn't find from squid documentation how to configure squid for this desired behavior (and if it is even possible). Could you please help me and tell me how should I configure squid for this purpose? Thank you.

  Read the article

• Teredo - how to connect to host behind NAT?

  - by Signum

  All I want to achieve is to establish connection to my simple server (written in C# using TcpListener class, if it makes any difference), on my computer which is behind NAT. It has some IPv6 address (it's public IP, starting with 2001:0) on Teredo interface. However, I cannot even ping it from outside my network, for instance I'm trying to ping this address from this website http://mebsd.com/ipv6-ping-and-traceroute, result - 100% packet loss. As I understood from reading about Teredo, there is no need for some port forwarding? So where could be the problem?

  Read the article

• Why aren't Heroku syslog drains logging to rsyslogd?

  - by Benjamin Oakes

  I'm having a problem using syslog drains as described in https://devcenter.heroku.com/articles/logging. To summarize, I have an Ubuntu 10.04 instance on EC2 that is running rsyslogd. I've also set up the security groups as they describe, and added a syslog drain using a command like heroku drains:add syslog://host1.example.com:514. I can send messages from the Heroku console to my rsyslogd instance via nc. I see them appear in the log file, so I know there isn't a firewall/security group issue.  However, Heroku does not seem to be forwarding log messages to the server that heroku drains lists. I would expect to see HTTP requests, Rails messages, etc. Is there something else I can try to figure this out? I'm new to rsyslogd, so I could easily be missing something.

  Read the article

• PuTTY/SSH: How to Prevent Auto-Logout?

  - by feklee

  My ISP's SSH server (Debian 2.0) logs me out after 35 minutes of inactivity, when connected with PuTTY (Windows XP). This is a big problem when I utilize the server for port-forwarding. The final messages displayed in the terminal: This terminal has been idle 30 minutes. If it remains idle for 5 more minutes it will be logged out by the system. Logged out by the system. PuTTY options that do not help: Sending of null packets to keep session active. Seconds between keepalives (0 to turn off): 30 [x] Enable TCP keepalives (SO_KEEPALIVE option) Any idea how to avoid the auto-log-out? Should I try another SSH client?

  Read the article

• mod_proxy failing as forward proxy in simple configuration

  - by Stabledog

  (On Mac OS X 10.6, Apache 2.2.11) Following the oft-repeated googled advice, I've set up mod_proxy on my Mac to act as a forward proxy for http requests. My httpd.conf contains this: <IfModule mod_proxy> ProxyRequests On ProxyVia On <Proxy *> Allow from all </Proxy> (Yes, I realize that's not ideal, but I'm behind a firewall trying to figure out why the thing doesn't work at all) So, when I point my browser's proxy settings to the local server (ip_address:80), here's what happens: I browse to http://www.cnn.com I see via sniffer that this is sent to Apache on the Mac Apache responds with its default home page ("It works!" is all this page says) So... Apache is not doing as expected -- it is not forwarding my browser's request out onto the Internet to cnn. Nothing in the logfile indicates an error or problem, and Apache returns a 200 header to the browser. Clearly there is some very basic configuration step I'm not understanding... but what?

  Read the article

• Connecting to local Sql server 2005 through Internet

  - by Manish

  Hello My Sql server is on Local Machine, I want to access it through Internet. I Configure Surace manager and Configuration manager of sqlserver 2005 for remote access. My sqlserver is running on port:1433 I am using port forwarding , I can access service of other ports, My Connetion String Is: Data Source=190.190.200.100,1433;Network Library=DBMSSOCN;Initial Catalog=myDataBase;User ID=myUsername;Password=myPassword; But it gives following error when i am trying to connect sql server through internet: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.)

  Read the article

• Content Length and Transfer Encoding Chunked nginx, node-http-proxy

  - by rampr

  I have the following setup - node-http-proxy acts as a reverse proxy forwarding all requests to nginx/socket.io as necessary My problem is this When I send a HTTP DELETE request from the browser, node-http-proxy adds a header "Transfer Encoding Chunked" as the request from the browser had no Content Length. The request from the browser had no Content Length as it had no body. Nginx doesn't like the Transfer Encoding Chunked Header and throws a 411 asking for Content-Length. The problem gets solved when I send dummy data as part of the DELETE request so there is a Content Length and node-http-proxy doesn't add Transfer Encoding Chunked header and nginx is happy. I want to understand if node-http-proxy isn't working as expected, because it adds a Transfer Encoding Chunked header when Content Length is missing because there is no Content Body.

  Read the article

• Can Remote Desktop be set up to use IPv6?

  - by Garrett

  I have both a Windows 7 Ultimate and a Windows XP Professional machine set up on my home network. I would like to be able to access them from school. Port forwarding is not currently an option (long story). Is there a way to set it so that I can RDP (yes it has to be RDP not something like TeamViewer or LogMeIn) over IPv6, possibly using Teredo? I have tried but I can't seem to get it working. Also I cannot ping these machines' IPv6 addresses. How can I get this set up?

  Read the article

• OS X Address Not Available - How do I open this port?

  - by GeoffreyF67

  I am trying to get xdebug working on my snow leopard box. It uses port 9000. When I ask slickedit to monitor this port is gives an error that the address is not available. I've gone to canyouseeme.org to see if the port is open. It says the port is NOT open. I've verified that I have that port forwarding to my box from the router and i do NOT have the mac firewall running. I'm stumped. Any ideas?

  Read the article

• openvpn and virtualbox

  - by hyperboreean

  Hi guys, I have a linux machine on which I occasionally run Windows XP in Virtual Box. All runs wonderful, except for the openvpn in XP, which can't connect to the vpn server running on a remote machine. The vpn client works from linux ... as far as I read until now it seems to be a problem of port forwarding ... I keep getting this error: TCP/UDP: Incoming packet rejected from 10.0.2.2:1194, expected peer address: (allow this incoming source address/port by removing --remote or adding --float) , but have no idea how to fix it.

  Read the article

• Routing from the DMZ to the interior network only

  - by Allan

  I have a home network connected to Verizon's FIOS service. Verizon's ActionTec router is connected to the ONT via coax to establish the MOCA network. My DD-WRT router's WAN port is connected to one of the ActionTec's LAN ports. The DD-WRT router is configured with a static IP address and assigned to the DMZ (this is done so I only have to configure port forwarding once). My issue is that this does not allow computers connected to the DD-WRT to serve streaming audio/video to the MOCA network using Verizon's Media Manager. I know that Media Manager uses ports 18001, 5050, and 5060, but I don't know how to forward those ports so that they are only available to the ActionTec's network and not the rest of the internet.

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - Setup guide recommendations?

  - by Peter Mounce

  I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. My ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• How do I access an Ubuntu VirtualBox guest at a static IP from an OS X host?

  - by David Siegel

  How does one configure an Ubuntu guest to use a static IP that's visible to an OS X host, and ensure that the static IP is independent of the host's network configuration? I previously used bridged networking for my guest, but I'm constantly moving my host between networks so the guest IP is always different. First, I tried setting the guest network configuration to NAT and forwarding host port 1022 to guest port 22, so I could at least ssh to a fixed address (localhost:1022): $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/Protocol" "TCP" $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/GuestPort" 22 $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/HostPort" 1022 Then, $ ssh localhost -p 1022 ssh: connect to host localhost port 1022: Connection refused But this didn't work (guest has no network access with NAT and OS X refused the connection, as you can see). I'd love a general solution that would let me communicate with my guest at a fixed IP.

  Read the article

• Nodejs for processing js and Nginx for handling everything else

  - by Kevin Parker

  I am having a nodejs running on port 8000 and nginx on port 80 on same server. I want Nginx to handle all the requests(image,css,etc) and forward js requests to nodejs server on port 8000. Is it possible to achieve this. i have configured nginx as reverse proxy but its forwarding every request to nodejs but i want nginx to process all except js. nginx/sites-enabled/default/ upstream nodejs { server localhost:8000; #nodejs } location / { proxy_pass http://192.168.2.21:8000; proxy_next_upstream error timeout invalid_header http_500 http_502 http_503 http_504; proxy_redirect off; proxy_buffering off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; }

  Read the article

• Gmail for Googleapps mail delivery issues

  - by epeleg

  I have a google apps domain running gmail. One of the owners of one of the email accounts is complaining that some emails don't get delivered to him. I sent him an email that did not get to its destination on one hand but I got no NDR on the other hand. I have already checked that the email was not on in his spam folder. The only thing that he has there is a forwarding rule that is also set up to leave the original in place. I am looking for any tools or ideas on how to debug this.

  Read the article

• Basic networking: Centos Server Router + Ubuntu Client setup.. unable to access outside world from client

  - by ale

  I am trying to set up my Centos Server with two NICs as a router. eth0 is connected to the outside world and eth1 is connected to an Ubuntu client. Here's eth0 on the server: DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=yes TYPE=Ethernet eth1 on the server: DEVICE=eth1 BOOTPROTO=static IPADDR=192.168.0.10 # a free address on my network ONBOOT=yes TYPE=Ethernet My server has IPv4 packet forwarding turned on and my iptables only contains: # iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE # iptables --append FORWARD --in-interface eth1 -j ACCEPT My Ubuntu client has this in its /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp gateway 192.168.0.10 but I can't get an Internet connection from the server for my client. I can't even ping my server from the client: $ ping 192.168.0.10 Destination Host Unreachable

  Read the article

• Connecting to a VirtualBox machine from the host, using an ip address

  - by Doron

  Hello, In a macbook host, I run VirtualBox having a guest ubuntu server, with a NAT network setting. In the virtual machine application "Parallels", I would get on the host an IP address of the guest, to which I could later set hostnames and access it directly. However, I couldn't find a way to accomplish this using VirtualBox. The only solution VirtualBox has for me, is to set port forwarding, and access "localhost" with these ports. How can I have the desired behavior set up, without having to change to a bridged network settings, and expose my guest computer to the network my host computer is connected to ? Thanks.

  Read the article

• How to prove that an email has been sent?

  - by bguiz

  Hi, I have a dispute on my hands in which the other party (landlord's real estate agent) dishonestly claims to not have received an email that I truly did send. My questions is, what are the ways to prove that the email was indeed sent? Thus far, the methods that I have already thought of are: Screenshot of the mail in the outbox Forwarding a copy of the original email I am aware of other things like HTTP/ SMTP headers etc that would exist as well. Are these useful for my purposes, and if so how do I extract these? The email in question was sent using Yahoo webmail ( http://au.mail.yahoo.com/ ). Edit: I am not seeking legal advice here, just technical advice as to how to gather this information.

  Read the article

• IIS not listening over external network, all other traffic working

  - by Beuy

  Hello there, I have a very odd situation, I have a server (let's call it X) running 2008 R2 with two NIC's in it, one is connected to the work domain and has a subnet of 192.168.10.0/24 the other is connected to a ADSL connection and has a subnet of 192.168.1.0/24. The server has IIS installed. On the ADSL connection I have setup a dynamic dns and port forwarding to allow external HTTP, HTTPS, FTP and RDP connections. FTP and RDP are working fine however neither HTTP or HTTPS are working at all. I can browse the websites by going to localhost on the machine, the HTTP and HTTPS ports appear as "Filtered" when I try to scan them using PortQueryUI and browsers respond with a "Server took too long to load or was not responding" error. This was working fine just a few days ago, Windows firewall is disabled I don't have any software firewall on it. And I'm really lost. Any help would be great.

  Read the article

• Hosting a web site at home: ISP Blocking port 80?

  - by tombull89

  Hello, I presume this is a better place to put this rather than server fault. I'm interested in setting up a small site to host at home as a "proof of concept" exercise, i.e. to prrove that I know how to do it. I've got a (virtual) server 2003 machine with a site on it, all configured with port forwarding through to 80 on my server. I have a Belkin F5D7634 which I have put my DYNDNS details in but when I try to go to my DYNDNS address it comes up with the page cannot be displayed. My ISP is Carphone Warehouse/AOL and I've been unable to find any information if they block port 80. If they do, can anybody reccomend a home provider that does not block port 80? Regards, Tom.

  Read the article

• How to get rid of NAT in a LAN?

  - by Alberto

  Currently the LAN I manage is organized as follows: internal network (192.168.1.0) which uses a Linux server as a gateway (internal address on interface br0 192.168.1.1, external address on interface br1 10.0.0.2) through NAT; then the 10.0.0.0 network has another gateway (10.0.0.1) which through another NAT connects the whole thing to the internet. What I would like to achieve is to configure the Linux server so that the first layer of NAT is no more necessary, so that for example a computer in the 10.0.0.0 network can ping every computer in the 192.168.1.0 network. I deleted this iptables rule: iptables -t nat -A POSTROUTING -o br1 -j SNAT --to-source 10.0.0.2, but of course now computers on 192.168.1.0 cannot reach the internet; ip forwarding is of course enabled. What's missing here? Thanks

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >