Search Results

Search found 15248 results on 610 pages for 'slashdot configuration'.

Page 573/610 | < Previous Page | 569 570 571 572 573 574 575 576 577 578 579 580  | Next Page >

• VPN in Ubuntu fails every time

  - by fazpas

  I am trying to setup a vpn connection in Ubuntu 10.04 to use the service from relakks.com I used the network manager to add the vpn connection and the settings are: Gateway: pptp.relakks.com Username: user Password: pwd IPv4 Settings: Automatic (VPN) Advanced: MSCHAP & MSCHAPv2 checked Use point-to-point encryption (security:default) Allow BSD data compression checked Allow deflate data compression checked Use TCP header compression checked The connection always fail, here is the syslog: Jun 27 20:11:56 desktop NetworkManager: <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'... Jun 27 20:11:56 desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' started (org.freedesktop.NetworkManager.pptp), PID 2064 Jun 27 20:11:56 desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' just appeared, activating connections Jun 27 20:11:56 desktop NetworkManager: <info> VPN plugin state changed: 3 Jun 27 20:11:56 desktop NetworkManager: <info> VPN connection 'Relakks' (Connect) reply received. Jun 27 20:11:56 desktop pppd[2067]: Plugin /usr/lib/pppd/2.4.5//nm-pptp-pppd-plugin.so loaded. Jun 27 20:11:56 desktop pppd[2067]: pppd 2.4.5 started by root, uid 0 Jun 27 20:11:56 desktop NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp1, iface: ppp1) Jun 27 20:11:56 desktop NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp1, iface: ppp1): no ifupdown configuration found. Jun 27 20:11:56 desktop pppd[2067]: Using interface ppp1 Jun 27 20:11:56 desktop pppd[2067]: Connect: ppp1 <--> /dev/pts/0 Jun 27 20:11:56 desktop pptp[2071]: nm-pptp-service-2064 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Jun 27 20:11:57 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 1 'Start-Control-Connection-Request' Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:739]: Received Start Control Connection Reply Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:773]: Client connection established. Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 7 'Outgoing-Call-Request' Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:858]: Received Outgoing Call Reply. Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:897]: Outgoing call established (call ID 0, peer's call ID 1024). Jun 27 20:11:59 desktop kernel: [ 56.564074] Inbound IN=ppp0 OUT= MAC= SRC=93.182.139.2 DST=186.110.76.26 LEN=61 TOS=0x00 PREC=0x00 TTL=52 ID=40460 DF PROTO=47 Jun 27 20:11:59 desktop kernel: [ 56.944054] Inbound IN=ppp0 OUT= MAC= SRC=93.182.139.2 DST=186.110.76.26 LEN=60 TOS=0x00 PREC=0x00 TTL=52 ID=40461 DF PROTO=47 Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[pptp_read_some:pptp_ctrl.c:544]: read returned zero, peer has closed Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[callmgr_main:pptp_callmgr.c:258]: Closing connection (shutdown) Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 12 'Call-Clear-Request' Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[pptp_read_some:pptp_ctrl.c:544]: read returned zero, peer has closed Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[call_callback:pptp_callmgr.c:79]: Closing connection (call state) Jun 27 20:11:59 desktop pppd[2067]: Modem hangup Jun 27 20:11:59 desktop pppd[2067]: Connection terminated. Jun 27 20:11:59 desktop NetworkManager: <info> VPN plugin failed: 1 Jun 27 20:11:59 desktop NetworkManager: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp1, iface: ppp1) Jun 27 20:11:59 desktop pppd[2067]: Exit. Does someone can identify something in the syslog? I've been googling and reading about pptp but couldn't find anything about the error "read returned zero, peer has closed"

  Read the article

• Unauthorized Access Exception using Web Deploy to Site when the site root is a UNC path

  - by Peter LaComb Jr.

  I am trying to use Web Deploy to deploy a site where the Site is rooted on a UNC path instead of a local drive. This is because I want to have a shared configuration, and have all servers point to the same UNC for content. That would allow me to deploy to one server and have all servers updated at the same time. I've created a share with everyone and users read/write. The NTFS permissions have the ID of the appDomain account as full control, and that is the same account that is configured as the specific user in Management Service Delegation. I can log on to the destination server as that ID, access the share and create/delete files. However, I'm getting the following exception in my Microsoft Web Deploy log on the destination server: User: Client IP: 192.168.62.174 Content-Type: application/msdeploy Version: 9.0.0.0 MSDeploy.VersionMin: 7.1.600.0 MSDeploy.VersionMax: 9.0.1631.0 MSDeploy.Method: Sync MSDeploy.RequestId: c060c823-cdb4-4abe-8294-5ffbdc327d2e MSDeploy.RequestCulture: en-US MSDeploy.RequestUICulture: en-US ServerVersion: 9.0.1631.0 Skip: objectName="^configProtectedData$" Provider: auto, Path: A tracing deployment agent exception occurred that was propagated to the client. Request ID 'c060c823-cdb4-4abe-8294-5ffbdc327d2e'. Request Timestamp: '8/23/2012 11:01:56 AM'. Error Details: ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER Microsoft.Web.Deployment.DeploymentDetailedUnauthorizedAccessException: Unable to perform the operation ("Create Directory") for the specified directory ("\someserver.mydomain.local\sharename\sitename\applicationName"). This can occur if the server administrator has not authorized this operation for the user credentials you are using. Learn more at: http://go.microsoft.com/fwlink/?LinkId=221672#ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER. --- Microsoft.Web.Deployment.DeploymentException: The error code was 0x80070005. --- System.UnauthorizedAccessException: Access to the path '\someserver.mydomain.local\sharename\sitename\applicationName' is denied. at Microsoft.Web.Deployment.NativeMethods.RaiseIOExceptionFromErrorCode(Win32ErrorCode errorCode, String maybeFullPath) at Microsoft.Web.Deployment.DirectoryEx.CreateDirectory(String path) at Microsoft.Web.Deployment.DirPathProviderBase.CreateDirectory(String fullPath, DeploymentObject source) at Microsoft.Web.Deployment.DirPathProviderBase.Add(DeploymentObject source, Boolean whatIf) --- End of inner exception stack trace --- --- End of inner exception stack trace --- at Microsoft.Web.Deployment.FilePathProviderBase.HandleKnownRetryableExceptions(DeploymentBaseContext baseContext, Int32[] errorsToIgnore, Exception e, String path, String operation) at Microsoft.Web.Deployment.DirPathProviderBase.Add(DeploymentObject source, Boolean whatIf) at Microsoft.Web.Deployment.DeploymentObject.Add(DeploymentObject source, DeploymentSyncContext syncContext) at Microsoft.Web.Deployment.DeploymentSyncContext.HandleAdd(DeploymentObject destObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentSyncContext.HandleUpdate(DeploymentObject destObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenNoOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenNoOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.ProcessSync(DeploymentObject destinationObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentObject.SyncToInternal(DeploymentObject destObject, DeploymentSyncOptions syncOptions, PayloadTable payloadTable, ContentRootTable contentRootTable, Nullable1 syncPassId) at Microsoft.Web.Deployment.DeploymentAgent.HandleSync(DeploymentAgentAsyncData asyncData, Nullable1 passId) at Microsoft.Web.Deployment.DeploymentAgent.HandleRequestWorker(DeploymentAgentAsyncData asyncData) at Microsoft.Web.Deployment.DeploymentAgent.HandleRequest(DeploymentAgentAsyncData asyncData) This is shown as the following on the console of the machine where I run the deployment: C:\Users\PLaComb"C:\Program Files (x86)\IIS\Microsoft Web Deploy V3\msdeploy.exe" -source:package='C:\Packages\Deployments\applicationName.zip' -dest:auto,computerName='https://SERVERNAME:8172/msdeploy.axd',includeAcls='True' -verb:sync -disableLink:AppPoolExtension -disableLink:ContentExtension -disableLink:CertificateExtension -setParamFile:"C:\Packages\Deployments\applicationName.SetParameters.xml" -allowUntrusted Info: Using ID 'c060c823-cdb4-4abe-8294-5ffbdc327d2e' for connections to the remote server. Info: Adding sitemanifest (sitemanifest). Info: Adding virtual path (JMS/admin) Info: Adding directory (JMS/admin). Error Code: ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER More Information: Unable to perform the operation ("Create Directory") for the specified directory ("\someserver.mydomain.local\sharename\sitename\applicationName"). This can occur if the server administrator has not authorized this operation for the user credentials you are using. Learn more at: http://go.microsoft.com/fwlink/?LinkId=221672#ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER. Error: The error code was 0x80070005. Error: Access to the path '\someserver.mydomain.local\sharename\sitename\applicationName' is denied. Error count: 1.

  Read the article

• iptable CLUSTERIP won't work

  - by Rad Akefirad

  We have some requirements which explained here. We tried to satisfy them without any success as described. Here is the brief information: Here are requirements: 1. High Availability 2. Load Balancing Current Configuration: Server #1: one static (real) IP for each 10.17.243.11 Server #2: one static (real) IP for each 10.17.243.12 Cluster (virtual and shared among all servers) IP: 10.17.243.15 I tried to use CLUSTERIP to have the cluster IP by the following: on the server #1 iptables -I INPUT -i eth0 -d 10.17.243.15 -j CLUSTERIP --new --hashmode sourceip --clustermac 01:00:5E:00:00:20 --total-nodes 2 --local-node 1 on the server #2 iptables -I INPUT -i eth0 -d 10.17.243.15 -j CLUSTERIP --new --hashmode sourceip --clustermac 01:00:5E:00:00:20 --total-nodes 2 --local-node 2 When we try to ping 10.17.243.15 there is no reply. And the web service (tomcat on port 8080) is not accessible either. However we managed to get the packets on both servers by using TCPDUMP. Some useful information: iptable roules (iptables -L -n -v): Chain INPUT (policy ACCEPT 21775 packets, 1470K bytes) pkts bytes target prot opt in out source destination 0 0 CLUSTERIP all -- eth0 * 0.0.0.0/0 10.17.243.15 CLUSTERIP hashmode=sourceip clustermac=01:00:5E:00:00:20 total_nodes=2 local_node=1 hash_init=0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 14078 packets, 44M bytes) pkts bytes target prot opt in out source destination Log messages: ... kernel: [ 7.329017] e1000e: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None ... kernel: [ 7.329133] e1000e 0000:05:00.0: eth3: 10/100 speed: disabling TSO ... kernel: [ 7.329567] ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready ... kernel: [ 71.333285] ip_tables: (C) 2000-2006 Netfilter Core Team ... kernel: [ 71.341804] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) ... kernel: [ 71.343168] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully ... kernel: [ 108.456043] device eth0 entered promiscuous mode ... kernel: [ 112.678859] device eth0 left promiscuous mode ... kernel: [ 117.916050] device eth0 entered promiscuous mode ... kernel: [ 140.168848] device eth0 left promiscuous mode TCPDUMP while pinging: tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 12:11:55.335528 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 10.17.243.1 > 10.17.243.15: ICMP echo request, id 16162, seq 2390, length 64 12:11:56.335778 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 10.17.243.1 > 10.17.243.15: ICMP echo request, id 16162, seq 2391, length 64 12:11:57.336010 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 10.17.243.1 > 10.17.243.15: ICMP echo request, id 16162, seq 2392, length 64 12:11:58.336287 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 10.17.243.1 > 10.17.243.15: ICMP echo request, id 16162, seq 2393, length 64 And there is no ping reply as I said. Does anyone know which part I missed? Thanks in advance.

  Read the article

• Having problems with high CPU usage and apparent memory leak of Exim

  - by Dancrumb

  I'm having problems with my server and am hoping you can help. The culprit appears to be exim. The CPU usage is consistently high and the memory usage trends up and up and up for no apparent reason (this is not a heavily used server). To demonstrate the issue, I ran the following: root@server [/var/log]# service exim restart; for iter in `seq 0 9`; do date; top -n1 | grep exim; sleep 10; done Shutting down exim: [ OK ] Shutting down spamd: [ OK ] Starting exim: [ OK ] Sun Jun 6 18:12:07 CDT 2010 62592 root 25 0 11400 6572 2356 R 51.5 1.3 0:00.92 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim Sun Jun 6 18:12:18 CDT 2010 62592 root 25 0 28768 23m 2356 R 57.4 4.6 0:06.75 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:12:28 CDT 2010 62592 root 25 0 36408 30m 2356 R 55.5 6.0 0:12.59 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:12:39 CDT 2010 62592 root 25 0 41396 35m 2356 R 53.5 7.0 0:18.35 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:12:49 CDT 2010 62592 root 25 0 45868 40m 2356 R 47.5 7.8 0:24.06 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:13:00 CDT 2010 62592 root 25 0 50056 44m 2356 R 55.3 8.6 0:29.84 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:13:10 CDT 2010 62592 root 25 0 53888 47m 2356 R 55.2 9.4 0:35.63 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:13:21 CDT 2010 62592 root 20 0 56920 50m 2356 R 55.3 9.9 0:41.15 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:13:31 CDT 2010 62592 root 25 0 60380 54m 2356 R 53.4 10.6 0:46.98 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim Sun Jun 6 18:13:42 CDT 2010 62592 root 22 0 63400 57m 2356 R 49.5 11.2 0:52.74 exim 62587 mailnull 18 0 7548 1212 792 S 0.0 0.2 0:00.00 exim 62588 root 18 0 7536 2052 1648 S 0.0 0.4 0:00.00 exim After some time, it gets to a rate of picking up an extra MB every 10s. I've checked the exim logs and there are no messages coming in there. exim -bV shows: Exim version 4.69 #1 built 16-Mar-2009 14:44:43 Copyright (c) University of Cambridge 2006 Berkeley DB: Sleepycat Software: Berkeley DB 4.2.52: (February 22, 2005) Support for: crypteq iconv() IPv6 PAM Perl OpenSSL Content_Scanning Old_Demime Experimental_SPF Experimental_SRS Experimental_DomainKeys Lookups: lsearch wildlsearch nwildlsearch iplsearch dbm dbmnz passwd Authenticators: cram_md5 dovecot plaintext spa Routers: accept dnslookup ipliteral manualroute queryprogram redirect Transports: appendfile/maildir autoreply pipe smtp Size of off_t: 8 Configuration file is /etc/exim.conf I'm at something of a loss as to how to proceed. Any recommendations would be well received!

  Read the article

• Cannot join Win7 workstations to Win2k8 domain

  - by wfaulk

  I am trying to connect a Windows 7 Ultimate machine to a Windows 2k8 domain and it's not working. I get this error: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt. DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain "example.local": The query was for the SRV record for _ldap._tcp.dc._msdcs.example.local The following domain controllers were identified by the query: dc1.example.local dc2.example.local However no domain controllers could be contacted. Common causes of this error include: Host (A) or (AAAA) records that map the names of the domain controllers to their IP addresses are missing or contain incorrect addresses. Domain controllers registered in DNS are not connected to the network or are not running. The client is in an office connected remotely via MPLS to the data center where our domain controllers exist. I don't seem to have anything blocking connectivity to the DCs, but I don't have total control over the MPLS circuit, so it's possible that there's something blocking connectivity. I have tried multiple clients (Win7 Ultimate and WinXP SP3) in the one office and get the same symptoms on all of them. I have no trouble connecting to either of the domain controllers, though I have, admittedly, not tried every possible port. ICMP, LDAP, DNS, and SMB connections all work fine. Client DNS is pointing to the DCs, and "example.local" resolves to the two IP addresses of the DCs. I get this output from the NetLogon Test command line utility: C:\Windows\System32>nltest /dsgetdc:example.local Getting DC name failed: Status = 1355 0x54b ERROR_NO_SUCH_DOMAIN I have also created a separate network to emulate that office's configuration that's connected to the DC network via LAN-to-LAN VPN instead of MPLS. Joining Windows 7 computers from that remote network works fine. The only difference I can find between the two environments is the intermediate connectivity, but I'm out of ideas as to what to test or how to do it. What further steps should I take? (Note that this isn't actually my client workstation and I have no direct access to it; I'm forced to do remote hands access to it, which makes some of the obvious troubleshooting methods, like packet sniffing, more difficult. If I could just set up a system there that I could remote into, I would, but requests to that effect have gone unanswered.) 2011-08-25 update: I had DCDIAG.EXE run on a client attempting to join the domain: C:\Windows\System32>dcdiag /u:example\adminuser /p:********* /s:dc2.example.local Directory Server Diagnosis Performing initial setup: Ldap search capabality attribute search failed on server dc2.example.local, return value = 81 This sounds like it was able to connect via LDAP, but the thing that it was trying to do failed. But I don't quite follow what it was trying to do, much less how to reproduce it or resolve it. 2011-08-26 update: Using LDP.EXE to try and make an LDAP connection directly to the DCs results in these errors: ld = ldap_open("10.0.0.1", 389); Error <0x51: Fail to connect to 10.0.0.1. ld = ldap_open("10.0.0.2", 389); Error <0x51: Fail to connect to 10.0.0.2. ld = ldap_open("10.0.0.1", 3268); Error <0x51: Fail to connect to 10.0.0.1. ld = ldap_open("10.0.0.2", 3268); Error <0x51: Fail to connect to 10.0.0.2. This would seem to point fingers at LDAP connections being blocked somewhere. (And 0x51 == 81, which was the error from DCDIAG.EXE from yesterday's update.) I could swear I tested this using TELNET.EXE weeks ago, but now I'm thinking that I may have assumed that its clearing of the screen was telling me that it was waiting and not that it had connected. I'm tracking down LDAP connectivity problems now. This update may become an answer.

  Read the article

• TLS (STARTTLS) Failure After 10.6 Upgrade to Open Directory Master

  - by Thomas Kishel

  Hello, Environment: Mac OS X 10.6.3 install/import of a MacOS X 10.5.8 Open Directory Master server. After that upgrade, LDAP+TLS fails on our MacOS X 10.5, 10.6, CentOS, Debian, and FreeBSD clients (Apache2 and PAM). Testing using ldapsearch: ldapsearch -ZZ -H ldap://gnome.darkhorse.com -v -x -b "dc=darkhorse,dc=com" '(uid=donaldr)' uid ... fails with: ldap_start_tls: Protocol error (2) Testing adding "-d 9" fails with: res_errno: 2, res_error: <unsupported extended operation>, res_matched: <> Testing without requiring STARTTLS or with LDAPS: ldapsearch -H ldap://gnome.darkhorse.com -v -x -b "dc=darkhorse,dc=com" '(uid=donaldr)' uid ldapsearch -H ldaps://gnome.darkhorse.com -v -x -b "dc=darkhorse,dc=com" '(uid=donaldr)' uid ... succeeds with: # donaldr, users, darkhorse.com dn: uid=donaldr,cn=users,dc=darkhorse,dc=com uid: donaldr # search result search: 2 result: 0 Success # numResponses: 2 # numEntries: 1 result: 0 Success (We are specifying "TLS_REQCERT never" in /etc/openldap/ldap.conf) Testing with openssl: openssl s_client -connect gnome.darkhorse.com:636 -showcerts -state ... succeeds: CONNECTED(00000003) SSL_connect:before/connect initialization SSL_connect:SSLv2/v3 write client hello A SSL_connect:SSLv3 read server hello A depth=1 /C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=Dark Horse Network/CN=DHC MIS Department verify error:num=19:self signed certificate in certificate chain verify return:0 SSL_connect:SSLv3 read server certificate A SSL_connect:SSLv3 read server done A SSL_connect:SSLv3 write client key exchange A SSL_connect:SSLv3 write change cipher spec A SSL_connect:SSLv3 write finished A SSL_connect:SSLv3 flush data SSL_connect:SSLv3 read finished A --- Certificate chain 0 s:/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=MIS/CN=gnome.darkhorse.com i:/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=Dark Horse Network/CN=DHC MIS Department 1 s:/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=Dark Horse Network/CN=DHC MIS Department i:/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=Dark Horse Network/CN=DHC MIS Department --- Server certificate -----BEGIN CERTIFICATE----- <deleted for brevity> -----END CERTIFICATE----- subject=/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=MIS/CN=gnome.darkhorse.com issuer=/C=US/ST=Oregon/L=Milwaukie/O=Dark Horse Comics, Inc./OU=Dark Horse Network/CN=DHC MIS Department --- No client certificate CA names sent --- SSL handshake has read 2640 bytes and written 325 bytes --- New, TLSv1/SSLv3, Cipher is AES256-SHA Server public key is 1024 bit Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : AES256-SHA Session-ID: D3F9536D3C64BAAB9424193F81F09D5C53B7D8E7CB5A9000C58E43285D983851 Session-ID-ctx: Master-Key: E224CC065924DDA6FABB89DBCC3E6BF89BEF6C0BD6E5D0B3C79E7DE927D6E97BF12219053BA2BB5B96EA2F6A44E934D3 Key-Arg : None Start Time: 1271202435 Timeout : 300 (sec) Verify return code: 0 (ok) So we believe that the slapd daemon is reading our certificate and writing it to LDAP clients. Apple Server Admin adds ProgramArguments ("-h ldaps:///") to /System/Library/LaunchDaemons/org.openldap.slapd.plist and TLSCertificateFile, TLSCertificateKeyFile, TLSCACertificateFile, and TLSCertificatePassphraseTool to /etc/openldap/slapd_macosxserver.conf when enabling SSL in the LDAP section of the Open Directory service. While that appears enough for LDAPS, it appears that this is not enough for TLS. Comparing our 10.6 and 10.5 slapd.conf and slapd_macosxserver.conf configuration files yields no clues. Replacing our certificate (generated with a self-signed ca) with an Apple Server Admin generated self signed certificate results in no change in ldapsearch results. Setting -d to 256 in /System/Library/LaunchDaemons/org.openldap.slapd.plist logs: 4/13/10 5:23:35 PM org.openldap.slapd[82162] conn=384 op=0 EXT oid=1.3.6.1.4.1.1466.20037 4/13/10 5:23:35 PM org.openldap.slapd[82162] conn=384 op=0 do_extended: unsupported operation "1.3.6.1.4.1.1466.20037" 4/13/10 5:23:35 PM org.openldap.slapd[82162] conn=384 op=0 RESULT tag=120 err=2 text=unsupported extended operation Any debugging advice much appreciated. -- Tom Kishel

  Read the article

• SATA drive problems with two SIL RAID cards

  - by Jon Topper

  I've just put a second SiI 3114 SATARaid card in my home server so that I could add another pair of SATA drives and increase my storage space. Annoyingly, it doesn't seem to work: [ 32.816030] ata5: lost interrupt (Status 0x0) [ 32.816072] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 32.816091] ata5.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in [ 32.816094] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 32.816101] ata5.00: status: { DRDY } [ 32.816117] ata5: hard resetting link [ 33.136082] ata5: SATA link down (SStatus 0 SControl 0) [ 36.060940] irq 18: nobody cared (try booting with the "irqpoll" option) [ 36.060949] Pid: 0, comm: swapper Not tainted 2.6.31-20-generic #58-Ubuntu [ 36.060954] Call Trace: [ 36.060977] [] ? printk+0x18/0x1c [ 36.060997] [] __report_bad_irq+0x27/0x90 [ 36.061005] [] note_interrupt+0x150/0x190 [ 36.061011] [] handle_fasteoi_irq+0xac/0xd0 [ 36.061023] [] handle_irq+0x18/0x30 [ 36.061029] [] do_IRQ+0x47/0xc0 [ 36.061042] [] ? irq_exit+0x50/0x70 [ 36.061058] [] ? smp_apic_timer_interrupt+0x57/0x90 [ 36.061065] [] common_interrupt+0x30/0x40 [ 36.061075] [] ? native_safe_halt+0x5/0x10 [ 36.061082] [] default_idle+0x46/0xd0 [ 36.061088] [] cpu_idle+0x8c/0xd0 [ 36.061103] [] rest_init+0x55/0x60 [ 36.061111] [] start_kernel+0x2e6/0x2ec [ 36.061117] [] ? unknown_bootoption+0x0/0x19e [ 36.061133] [] i386_start_kernel+0x7c/0x83 [ 36.061137] handlers: [ 36.061139] [] (sil_interrupt+0x0/0xb0) [ 36.061151] Disabling IRQ #18 [ 38.136014] ata5: hard resetting link [ 38.456022] ata5: SATA link down (SStatus 0 SControl 0) [ 43.456013] ata5: hard resetting link [ 43.776022] ata5: SATA link down (SStatus 0 SControl 0) [ 43.776035] ata5.00: disabled [ 43.776055] ata5.00: device reported invalid CHS sector 0 [ 43.776074] sd 4:0:0:0: [sde] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 43.776082] sd 4:0:0:0: [sde] Sense Key : Aborted Command [current] [descriptor] [ 43.776092] Descriptor sense data with sense descriptors (in hex): [ 43.776097] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 43.776112] 00 00 00 00 [ 43.776118] sd 4:0:0:0: [sde] Add. Sense: No additional sense information [ 43.776127] end_request: I/O error, dev sde, sector 0 [ 43.776136] Buffer I/O error on device sde, logical block 0 [ 43.776170] ata5: EH complete [ 43.776187] ata5.00: detaching (SCSI 4:0:0:0) root@core:~# cat /proc/interrupts CPU0 0: 47 IO-APIC-edge timer 1: 8 IO-APIC-edge i8042 6: 3 IO-APIC-edge floppy 7: 0 IO-APIC-edge parport0 8: 0 IO-APIC-edge rtc0 9: 0 IO-APIC-fasteoi acpi 14: 53069 IO-APIC-edge pata_sis 15: 53004 IO-APIC-edge pata_sis 17: 112265 IO-APIC-fasteoi sata_sil 18: 200002 IO-APIC-fasteoi sata_sil, SiS SI7012 19: 111140 IO-APIC-fasteoi eth0 20: 0 IO-APIC-fasteoi ohci_hcd:usb2 21: 0 IO-APIC-fasteoi ohci_hcd:usb3 23: 0 IO-APIC-fasteoi ehci_hcd:usb1 NMI: 0 Non-maskable interrupts LOC: 6650492 Local timer interrupts SPU: 0 Spurious interrupts CNT: 0 Performance counter interrupts PND: 0 Performance pending work RES: 0 Rescheduling interrupts CAL: 0 Function call interrupts TLB: 0 TLB shootdowns TRM: 0 Thermal event interrupts THR: 0 Threshold APIC interrupts MCE: 0 Machine check exceptions MCP: 160 Machine check polls ERR: 0 MIS: 0 root@core:~# lspci | grep Raid 00:09.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 00:0a.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) root@core:~# lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 9.10 Release: 9.10 Codename: karmic root@core:~# uname -a Linux core.topper.me.uk 2.6.31-20-generic #58-Ubuntu SMP Fri Mar 12 05:23:09 UTC 2010 i686 GNU/Linux I've tried a combination of different kernel options (irqpoll, noapic, noacpi, pci=noapic) all to no avail. Does anyone have any bright ideas about how I can go about making this work? Swapping PCI cards around isn't an option as there are only two slots in this motherboard (an ASRock K7S41GX). The BIOS doesn't look to have too much in the way of configuration options regarding IRQ usage. Plan B is to ditch this server completely and buy a new QNAP for these drives to go in, but I was hoping to avoid doing this right now.

  Read the article

• DNS request timed out. timeout was 2 seconds

  - by sahil007

  i had setup bind dns server on centos. from local lan it will work fine but from remote when i tried to nslookup ..it will give reply like "DNS request timed out...timeout was 2 seconds." what is the problem? this is my bind config---- // Red Hat BIND Configuration Tool options { directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; query-source address * port 53; }; controls { inet 127.0.0.1 allow {localhost; } keys {rndckey; }; }; acl internals { 127.0.0.0/8; 192.168.0.0/24; 10.0.0.0/8; }; view "internal" { match-clients { internals; }; recursion yes; zone "mydomain.com" { type master; file "mydomain.com.zone"; }; zone "0.168.192.in-addr.arpa" { type master; file "0.168.192.in-addr.arpa.zone"; }; zone "." IN { type hint; file "named.root"; }; zone "localdomain." IN { type master; file "localdomain.zone"; allow-update { none; }; }; zone "localhost." IN { type master; file "localhost.zone"; allow-update { none; }; }; zone "0.0.127.in-addr.arpa." IN { type master; file "named.local"; allow-update { none; }; }; zone "0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa." I N { type master; file "named.ip6.local"; allow-update { none; }; }; zone "255.in-addr.arpa." IN { type master; file "named.broadcast"; allow-update { none; }; }; zone "0.in-addr.arpa." IN { type master; file "named.zero"; allow-update { none; }; }; }; view "external" { match-clients { any; }; recursion no; zone "mydomain.com" { type master; file "mydomain.com.zone"; // file "/var/named/chroot/var/named/mydomain.com.zone"; }; zone "0.168.192.in-addr.arpa" { type master; file "0.168.192.in-addr.arpa.zone"; }; }; include "/etc/rndc.key";

  Read the article

• Apache cyclic redirection problem

  - by slicedlime

  I have an extremely weird problem with one of my sites. I run a number of blogs off a single apache2 server with a shared wordpress install. Each site has a www.domain.com main domain, but a ServerAlias of domain.com. This works fine for all the blogs except one, which instead of redirecting to www.domain.com redirects to domain.com, causing a cyclic redirection. The configuration for each host looks like this: <VirtualHost *:80> ServerName www.domain.com ServerAlias domain.com DocumentRoot "/home/www/www.domain.com" <Directory "/home/www/www.domain.com"> Options MultiViews Indexes Includes FollowSymLinks ExecCGI AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> As this didn't work, I tried a mod_rewrite rule for it, which still didn't redirect correctly. The weird thing here is that if i rewrite it to redirect to any other domain it will redirect correctly, even to another subdomain. So a rewrite rule for domain.com that redirects to foo.domain.com works, but not to www.domain.com. In the same way, trying to redirec to www.domain.com/foo/ ends me up with a redirection to domain.com/foo/. Even weirder, I tried setting up domain.com as a completely separate virtual host, and ran this php test script as index.php on it: <?php header('Location: http://www.domain.com/' . $_SERVER["request_uri"]); ?> Hitting domain.com still redirects to domain.com! Checking out the headers sent to the server verifies that I get exactly the redirect URL I wanted, except with the "www." stripped. The same script works like a charm if I replace www. with foo or redirect to any other domain. This has now foiled me for a long time. I've diffed the vhosts configs for a working domain and the faulty one, and the only difference is the domain name itself. I've diffed the .htaccess files for both sites, and the only difference is a path related to the sharing of wordpress installation for the blogs: php_value include_path ".:/home/www/www.domain.com/local/:/home/www/www.domain.com/" I searched through everything in /etc (including apache conf) for the domain name of the faulty host and found nothing weird, searched through everything in /etc for one of the working ones to make sure it didn't differ, I even went so far to check on the DNS setup of two domains to make sure there wasn't anything strange going on. Here's the response for the faulty one: user@localhost dir $ wget -S domain.com --2010-03-20 21:47:24-- http://domain.com/ Resolving domain.com... x.x.x.x Connecting to domain.com|x.x.x.x|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 301 Moved Permanently Via: 1.1 ISA Connection: Keep-Alive Proxy-Connection: Keep-Alive Content-Length: 0 Date: Sat, 20 Mar 2010 20:47:24 GMT Location: http://domain.com/ Content-Type: text/html; charset=UTF-8 Server: Apache X-Powered-By: PHP/5.2.10-pl0-gentoo X-Pingback: http://domain.com/xmlrpc.php Keep-Alive: timeout=15, max=100 Location: http://domain.com/ [following] And a working one: user@localhost dir $ wget -S domain.com --2010-03-20 21:51:33-- http://domain.com/ Resolving domain.com... x.x.x.x Connecting to domain.com|x.x.x.x|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 301 Moved Permanently Via: 1.1 ISA Connection: Keep-Alive Proxy-Connection: Keep-Alive Content-Length: 0 Date: Sat, 20 Mar 2010 20:51:33 GMT Location: http://www.domain.com/ Content-Type: text/html; charset=UTF-8 Server: Apache X-Powered-By: PHP/5.2.10-pl0-gentoo X-Pingback: http://www.domain.com/xmlrpc.php Keep-Alive: timeout=15, max=100 Location: http://www.domain.com/ [following] I'm stumped. I've had this problem for a long time, and I feel like I've tried everything. I can't see why the different domains would act differently under the same installation with the same settings. Help :(

  Read the article

• Varnish cached 'MISS status' object?

  - by Hesey

  My site uses nginx, varnish, jboss. And some url will be cached by varnish, it depends a response header from jboss. The first time, jboss tells varnish doesn't cache this url. Then the second request, jboss tells varnish to cache, but varnish won't cache it. I used varnishstat and found that 1 object is cached in Varnish, is that the 'MISS status' object? I remove grace code and the problem still exists. When I PURGE this url, varnish works fine and cache the url then. But I can't PURGE so much urls every startup time, how can I fix this? The configuration: acl local { "localhost"; } backend default { .host = "localhost"; .port = "8080"; .probe = { .url = "/preload.htm"; .interval = 3s; .timeout = 1s; .window = 5; .threshold = 3; } } sub vcl_deliver { if (req.request == "PURGE") { remove resp.http.X-Varnish; remove resp.http.Via; remove resp.http.Age; remove resp.http.Content-Type; remove resp.http.Server; remove resp.http.Date; remove resp.http.Accept-Ranges; remove resp.http.Connection; set resp.http.keeplive="true"; } else { if (obj.hits > 0) { set resp.http.X-Cache = "HIT"; } else { set resp.http.X-Cache = "MISS"; } } } sub vcl_recv { if(req.url ~ "/check.htm"){ error 404 "N"; } if( req.http.host ~ "store." || req.request == "POST"){ return (pipe); } if (req.backend.healthy) { set req.grace = 30s; } else { set req.grace = 10m; } set req.http.x-cacheKey = "0"; if(req.url ~ "/shop/view_shop.htm" || req.url ~ "/shop/viewShop.htm" || req.url ~ "/index.htm"){ if(req.url ~ "search=y"){ set req.http.x-cacheKey = req.http.host + "/search.htm"; }else if(req.url !~ "bbs=y" && req.url !~ "shopIntro=y" && req.url !~ "shop_intro=y"){ set req.http.x-cacheKey = req.http.host + "/index.htm"; } }else if(req.url ~ "/search"){ set req.http.x-cacheKey = req.http.host + "/search.htm"; } if( req.http.x-cacheKey == "0" && req.url !~ "/i/"){ return (pipe); } if (req.request == "PURGE") { if (client.ip ~ local) { return (lookup); } else { error 405 "Not allowed."; } } if (req.url ~ "/i/") { set req.http.x-shop-url = req.original_url; }else { unset req.http.cookie; } } sub vcl_fetch { set beresp.grace = 10m; #unset beresp.http.x-cacheKey; if (req.url ~ "/i/" || req.url ~ "status" ){ set beresp.ttl = 0s; /* ttl=0 for dynamic content */ } else if(beresp.http.x-varnish-cache != "1"){ set beresp.do_esi = true; /* Do ESI processing */ set beresp.ttl = 0s; unset beresp.http.set-cookie; } else { set beresp.do_esi = true; /* Do ESI processing */ set beresp.ttl = 1800s; unset beresp.http.set-cookie; } } sub vcl_hash { hash_data(req.http.x-cacheKey); return (hash); } sub vcl_error { if (req.request == "PURGE") { return (deliver); } else { set obj.http.Content-Type = "text/html; charset=gbk"; synthetic {"<!--ve-->"}; return (deliver); } } sub vcl_hit { if (req.request == "PURGE") { set obj.ttl = 0s; error 200 "Purged."; } } sub vcl_miss { if (req.request == "PURGE") { error 404 "N"; } }

  Read the article

• CakePhp on IIS: How can I Edit URL Rewrite module for SSL Redirects

  - by AdrianB

  I've not dealt much with IIS rewrites, but I was able to import (and edit) the rewrites found throughout the cake structure (.htaccess files). I'll explain my configuration a little, then get to the meat of the problem. So my Cake php framework is working well and made possible by the url rewrite module 2.0 which I have successfully installed and configured for the site. The way cake is set up, the webroot folder (for cake, not iis) is set as the default folder for the site and exists inside the following hierarchy inetpub -wwwroot --cakePhp root ---application ----models ----views ----controllers ----WEBROOT // *** HERE *** ---cake core --SomeOtherSite Folder For this implementation, the url rewrite module uses the following rules (from the web.config file) ... <rewrite> <rules> <rule name="Imported Rule 1" stopProcessing="true"> <match url="^(.*)$" ignoreCase="false" /> <conditions logicalGrouping="MatchAll"> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> </conditions> <action type="Rewrite" url="index.php?url={R:1}" appendQueryString="true" /> </rule> <rule name="Imported Rule 2" stopProcessing="true"> <match url="^$" ignoreCase="false" /> <action type="Rewrite" url="/" /> </rule> <rule name="Imported Rule 3" stopProcessing="true"> <match url="(.*)" ignoreCase="false" /> <action type="Rewrite" url="/{R:1}" /> </rule> <rule name="Imported Rule 4" stopProcessing="true"> <match url="^(.*)$" ignoreCase="false" /> <conditions logicalGrouping="MatchAll"> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> </conditions> <action type="Rewrite" url="index.php?url={R:1}" appendQueryString="true" /> </rule> </rules> </rewrite> I've Installed my SSL certificate and created a site binding so that if i use the https:// protocol, everything is working fine within the site. I fear that attempts I have made at creating a rewrite are too far off base to understand results. The rules need to switch protocol without affecting the current set of rules which pass along url components to index.php (which is cake's entry point). My goal is this- Create a couple of rewrite rules that will [#1] redirect all user pages (in this general form http://domain.com/users/page/param/param/?querystring=value ) to use SSL and then [#2} direct all other https requests to use http (is this is even necessary?). [e.g. http://domain.com/users/login , http://domain.com/users/profile/uid:12345 , http://domain.com/users/payments?firsttime=true] ] to all use SSL [e.g. https://domain.com/users/login , https://domain.com/users/profile/uid:12345 , https://domain.com/users/payments?firsttime=true] ] Any help would be greatly appreciated.

  Read the article

• RAID and Partitions, guidance Needed

  - by beauregarde

  Alright I have a Biostar TA790GX3A2+ Mobo 2x Seagate 750Gb Hard drive (with 2 different speeds) an X4 9750 A GeForce 9800GT and 2GB RAM Hardware Specs link text I want to configure my computer with partitions in various RAID arrays. The Partitions I know i want (disk letters are mostly for reference here) C: XP Boot D: XP Swap E: XP Run F: Games G: Data The Partitions I think I want (repeat caveat) H: small FAT for Win Legacy and DOS I: Linux J: Linux Swap K-?M?: Other Linux /whatever partitions N & O: Attic for D1 and D2 What I'd like to do, is have C: written on Disk 1 (D1),.. D: on D2,.. E: and F: striped on D1 & D2,.. G: mirrored or D1 & D2,.. I: on D2 (so i can just switch disc boot priority to open in Ubuntu),.. J: on D1,.. and H: somewhere low on D1 I am inexperienced with VMs, so i am unsure as to whether those run out of XP, or whether i need to reserve a primary partition for them. However, I think they would be preferable for testing new OS's to scheduling a partition for the same purpose. I'm also not married to XP, but -64 IS pretty important to me. QUestion Time 1) Ignoring the irrationality of it all, is such a configuration possible? If not, can some pseudo-approximation be achieved? 2) My RAID is software, isnt it? 3) How much should I short a 750GB HD? And should i use that space for my attics, or for my attics and something else, or for something else (.iso's perhaps?)? 4) if XP is striped on D1 & D2, will that interfere egregiously with my Swap writes on D2? If so, would striping both XP and Swap relieve (or at least mitigate) that issue? Should XP and Swap just be written normally on 2 different HDs? 5) Should I keep DL's and Drivers on E: (XP Run), F: (Games), or elsewhere? 6) Is 4GB enough for C:? 7) Is 30GB enough (or too much) for E:? 8) How much to reserve for the Linux and sub-Linux partitions? Also, where on the platter do you think i should put them? 9) Am I a fool to use FAT16 instead of FAT32 for H: because I'd rather run 95 than 98SE? If not, do you think 2GB or 4GB? 10) I cant predict what my Max Commit Charge will be, so recommendations for Pagefile size? 5GB? 12GB? 11) VMs, where do I run them? do they exacerbate anything? Would it be better to just emulate Linux, 95, and DOS? EC) What havent I considered that I really should? Notes: computer is mostly for playing games and watching media, though I wouldnt rule out the use of particularly blah-intensive anything.

  Read the article

• routing specific IP to ppp0 tunnel

  - by gompertz

  Hi All, I feel I've struggled with this long enough and need some help. I have a pptp tunnel and am trying to route destination traffic from 208.85.40.20 to the pptp tunnel (ppp0). (Keen observers may recognize the ip as being that of pandora.com). I am doing all this configuration on a router... and I know it's not working successfully as traceroute yields nothing but astericks. I've pasted relevant outputs below: (with some "security" editing to the addresses) root@OpenWrt:~# ifconfig br0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28185 errors:0 dropped:0 overruns:0 frame:0 TX packets:24936 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4894242 (4.6 MiB) TX bytes:5941902 (5.6 MiB) eth0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:51829 errors:0 dropped:0 overruns:0 frame:0 TX packets:56824 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11490288 (10.9 MiB) TX bytes:11857913 (11.3 MiB) Interrupt:4 eth2 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:15426 TX packets:9529 errors:21 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:423 (423.0 B) TX bytes:596036 (582.0 KiB) Interrupt:2 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:30 errors:0 dropped:0 overruns:0 frame:0 TX packets:30 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2300 (2.2 KiB) TX bytes:2300 (2.2 KiB) ppp0 Link encap:Point-Point Protocol inet addr:68.68.39.250 P-t-P:172.16.20.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:165 errors:2 dropped:0 overruns:0 frame:0 TX packets:68 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:7006 (6.8 KiB) TX bytes:3462 (3.3 KiB) vlan0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:28182 errors:0 dropped:0 overruns:0 frame:0 TX packets:33813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5006544 (4.7 MiB) TX bytes:6609774 (6.3 MiB) vlan1 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX inet addr:173.183.111.3 Bcast:173.183.111.255 Mask:255.255.224.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23653 errors:0 dropped:0 overruns:0 frame:0 TX packets:23012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5522012 (5.2 MiB) TX bytes:4982944 (4.7 MiB) wds0.4915 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wds0.4915 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@OpenWrt:~# cat /etc/ppp/ip-up iptables -A FORWARD -t filter -i br0 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -t filter -i ppp0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -s 192.168.1.1/24 -d 0/0 -j MASQUERADE iptables -A forwarding_rule -o ppp0 -j ACCEPT iptables -A forwarding_rule -i ppp0 -j ACCEPT iptables -t nat -A postrouting_rule -o ppp0 -j MASQUERADE root@OpenWrt:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.16.20.1 * 255.255.255.255 UH 0 0 0 ppp0 208.85.40.20 * 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 173.183.192.0 * 255.255.224.0 U 0 0 0 vlan1 default d173-183-192-1. 0.0.0.0 UG 0 0 0 vlan1 default 192.168.1.1 0.0.0.0 UG 0 0 0 br0 Any advice is greatly appreciated, I'm not too great with network but am pretty astute at learning ;-)

  Read the article

• cron.daily not running at the time it should?

  - by Mariano Martinez Peck

  My /etc/cron.daily scripts seem to be executing far later from what I understand they should. I am in Ubuntu and anacron is installed. If I do a sudo cat /var/log/syslog | grep cron I get something like: Aug 23 01:17:01 mymachine CRON[25171]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 02:17:01 mymachine CRON[25588]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 03:17:01 mymachine CRON[26026]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 03:25:01 mymachine CRON[30320]: (root) CMD (test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily )) Aug 23 04:17:01 mymachine CRON[26363]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 05:17:01 mymachine CRON[26770]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 06:17:01 mymachine CRON[27168]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 07:17:01 mymachine CRON[27547]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 07:30:01 mymachine CRON[2249]: (root) CMD (start -q anacron || :) Aug 23 07:30:02 mymachine anacron[2252]: Anacron 2.3 started on 2014-08-23 Aug 23 07:30:02 mymachine anacron[2252]: Will run job `cron.daily' in 5 min. Aug 23 07:30:02 mymachine anacron[2252]: Jobs will be executed sequentially Aug 23 07:35:02 mymachine anacron[2252]: Job `cron.daily' started As you can see, at 3:25 it tried to do something. But the cron.daily execution started really at 7:35. My /etc/crontab is: # /etc/crontab: system-wide crontab # Unlike any other crontab you don't have to run the `crontab' # command to install the new version when you edit this file # and files in /etc/cron.d. These files also have username fields, # that none of the other crontabs do. SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin # m h dom mon dow user command 17 * * * * root cd / && run-parts --report /etc/cron.hourly 25 3 * * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily ) 47 6 * * 7 root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.weekly ) 52 6 1 * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.monthly ) # From what I understand, daily scripts are indeed for 3:25. My /etc/anacrontab is: # /etc/anacrontab: configuration file for anacron # See anacron(8) and anacrontab(5) for details. SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin HOME=/root LOGNAME=root # These replace cron's entries 1 5 cron.daily run-parts --report /etc/cron.daily 7 10 cron.weekly run-parts --report /etc/cron.weekly @monthly 15 cron.monthly run-parts --report /etc/cron.monthly So...does someone know why my cron started to do something at 3:25 but then really start the jobs at 7:35? Also..as you can see in the log, hourly jobs are being executed at correct time: hour and 17 minutes, which is exactly what I have in /etc/crontab Finally, from the logs, it seems my daily jobs are being actually run by anacron rather than cron? So cron finds nothing to run (at 3:25) and then anacron runs the jobs at 7:35? If true, how can I fix this? Thanks in advance,

  Read the article

• how to make bridge networking with KVM work in Fedora19

  - by netllama

  I'm attempting to get several virtual machines setup on a Fedora-19 host system, with the traditional bridge network devices (br0, br1, etc). I've done this many times before with older versions of Fedora (16, 14, etc), and it just works. However, for reasons that I cannot figure out, the bridge doesn't seem to be working in Fedora19. While I can successfully connect to the outside world (local network + internet) from inside a VM, nothing can communicate with the VM from outside (local network). I'm referring to something as trivial as pinging. From inside the VM, I can ping anything successfully (0% packet loss). However, from outside the VM (on the host, or any other system on the same network), I see 100% packet loss when pinging the IP address of the VM. My first question is simply, does anyone else have this working successfully in F19? And if so, what steps did you need to follow? I'm not using NetworkManager at all, its all the network service. There are no firewalls involved anywhere (iptables & firewall services are currently disabled). Here's the current host configuration: # brctl show bridge name bridge id STP enabled interfaces br0 8000.38eaa792efe5 no em2 vnet1 br1 8000.38eaa792efe6 no em3 br2 8000.38eaa792efe7 no em4 vnet0 virbr0 8000.525400db3ebf yes virbr0-nic # more /etc/sysconfig/network-scripts/ifcfg-em2 TYPE=Ethernet BRIDGE="br0" NAME=em2 DEVICE="em2" UUID=aeaa839e-c89c-4d6e-9daa-79b6a1b919bd ONBOOT=yes HWADDR=38:EA:A7:92:EF:E5 NM_CONTROLLED="no" # more /etc/sysconfig/network-scripts/ifcfg-br0 TYPE=Bridge NM_CONTROLLED="no" BOOTPROTO=dhcp NAME=br0 DEVICE="br0" ONBOOT=yes # ifconfig em2 ;ifconfig br0 em2: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet6 fe80::3aea:a7ff:fe92:efe5 prefixlen 64 scopeid 0x20<link> ether 38:ea:a7:92:ef:e5 txqueuelen 1000 (Ethernet) RX packets 100093 bytes 52354831 (49.9 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 25321 bytes 15791341 (15.0 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device memory 0xf7d00000-f7e00000 br0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 10.31.99.226 netmask 255.255.252.0 broadcast 10.31.99.255 inet6 fe80::3aea:a7ff:fe92:efe5 prefixlen 64 scopeid 0x20<link> ether 38:ea:a7:92:ef:e5 txqueuelen 0 (Ethernet) RX packets 19619 bytes 1963328 (1.8 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 11 bytes 1074 (1.0 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 Relevant section from /etc/libvirt/qemu/foo.xml (one of the VMs with this problem): <interface type='bridge'> <mac address='52:54:00:26:22:9d'/> <source bridge='br0'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> # ps -ef | grep qemu qemu 1491 1 82 13:25 ? 00:42:09 /usr/bin/qemu-system-x86_64 -machine accel=kvm -name cuda-linux64-build5 -S -machine pc-0.13,accel=kvm,usb=off -cpu SandyBridge,+pdpe1gb,+osxsave,+dca,+pcid,+pdcm,+xtpr,+tm2,+est,+smx,+vmx,+ds_cpl,+monitor,+dtes64,+pbe,+tm,+ht,+ss,+acpi,+ds,+vme -m 16384 -smp 6,sockets=6,cores=1,threads=1 -uuid 6e930234-bdfd-044d-2787-22d4bbbe30b1 -no-user-config -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/cuda-linux64-build5.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=localtime -no-shutdown -device piix3-usb-uhci,id=usb,bus=pci.0,addr=0x1.0x2 -drive file=/var/lib/libvirt/images/cuda-linux64-build5.img,if=none,id=drive-virtio-disk0,format=raw,cache=writeback -device virtio-blk-pci,scsi=off,bus=pci.0,addr=0x4,drive=drive-virtio-disk0,id=virtio-disk0,bootindex=1 -netdev tap,fd=25,id=hostnet0,vhost=on,vhostfd=26 -device virtio-net-pci,netdev=hostnet0,id=net0,mac=52:54:00:26:22:9d,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -vnc 127.0.0.1:1 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x5 I can provide additional information, if requested. thanks!

  Read the article

• Why doesn't this for loop work?

  - by evilsoup

  This is on Ubuntu 12.04 I'm trying to figure out how to get ffmpeg to do a batch conversion of FLACs to MP3, recursively. If I cd into a directory and use for f in *.flac; do ffmpeg -i "$f" -c:a libmp3lame -q:a 2 "${f/%flac/mp3}"; done that works perfectly fine. However, when I try this, it doesn't work: for f in "$(find . -type f -name *.flac)"; do ffmpeg -i "$f" -c:a libmp3lame -q:a 2 "${f/%flac/mp3}"; done It doesn't even throw up any useful errors (but here is the output anyway, no need to complain): evilsoup@enchantment:~/Music/Jean Sibelius$ for f in "$(find . -type f -name *.flac)"; do ffmpeg -i "$f" -c:a libmp3lame -q:a 2 "${f/%flac/mp3}"; done ffmpeg version git-2012-12-18-b7e085a Copyright (c) 2000-2012 the FFmpeg developers built on Dec 18 2012 19:23:11 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --enable-gpl --enable-libfaac --enable-libfdk-aac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-x11grab --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 12.100 / 52. 12.100 libavcodec 54. 80.100 / 54. 80.100 libavformat 54. 49.102 / 54. 49.102 libavdevice 54. 3.102 / 54. 3.102 libavfilter 3. 28.100 / 3. 28.100 libswscale 2. 1.103 / 2. 1.103 libswresample 0. 17.102 / 0. 17.102 libpostproc 52. 2.100 / 52. 2.100 ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/02. Symphony No.1.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/03. Symphony No.1.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/stripped2.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/05. Symphony No.1.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/stripped3.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/09. Andante festivo.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/08. Symphony No.3.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/01. Finlandia.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/07. Symphony No.3.flac ./Symphonies 1, 2, 3 & 5 I've tested the find command on its own, and it works as expected, so the problem has to be something to do with the interaction between find and for. I'm aware that I could do something with find's -exec option, but I can't find any way to do string substitution as I can with a bash for loop, and I'd rather not have a bunch of file.flac.mp3s to deal with, even if they could be fixed with a simple rename.

  Read the article

• Do I need to be worried about these SMART drive temperatures?

  - by Steve Lorimer

  I have 5 hard drives in a machine sitting in a cupboard. /dev/sda is a 500GB Seagate drive, and is the boot disk. /dev/sd{b,c,d,e} are 2TB drives in a raid6 configuration. smartctl is showing significantly higher temperatures (like ~140 degrees celsius) on the raid drives than the boot drive. Do I need to be worried? /dev/sdb and /dev/sde are new Western Digital Black drives (new=1 week) /dev/sdc and /dev/sdd are 5 year old Hitachi drives /dev/sda [SAT], Temperature_Celsius changed from 40 to 39 /dev/sdc [SAT], Temperature_Celsius changed from 142 to 146 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 142 /dev/sdd [SAT], Temperature_Celsius changed from 142 to 146 /dev/sda [SAT], Airflow_Temperature_Cel changed from 61 to 62 /dev/sda [SAT], Temperature_Celsius changed from 39 to 38 /dev/sde [SAT], Temperature_Celsius changed from 107 to 108 /dev/sdb [SAT], Temperature_Celsius changed from 108 to 109 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 150 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 150 /dev/sda [SAT], Airflow_Temperature_Cel changed from 62 to 61 /dev/sda [SAT], Temperature_Celsius changed from 38 to 39 Update: Adding detailed drive information as per request: /dev/sda =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Pipeline HD 5900.2 Device Model: ST3500312CS Serial Number: 5VV47HXA LU WWN Device Id: 5 000c50 02aad5ad6 Firmware Version: SC13 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5900 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdb =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD2003FZEX-00Z4SA0 Serial Number: WD-WMC1F1398726 LU WWN Device Id: 5 0014ee 003b8bd25 Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdc =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1220F30WSTUD LU WWN Device Id: 5 000cca 369cc9f5d Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdd =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1220F30WST4D LU WWN Device Id: 5 000cca 369cc9f48 Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sde =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD2003FZEX-00Z4SA0 Serial Number: WD-WMC1F1483782 LU WWN Device Id: 5 0014ee 3002d235c Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled

  Read the article

• Where's the Swap File/Partition?

  - by chrisbunney

  I'm investigating the virtual memory configuration of a Debian based Amazon EC2 instance, and as my background isn't in system admin, I'm slightly confused by what I'm seeing. We're using MongoDB, and the monitoring server we have indicates that the Mongo process is using about 20GB of swap space, however I can't figure out where this is located on the server. As far as I can tell from using the various suggested methods from Google, there is either a much smaller amount, or none at all. top indicates that there is 1.8GB of swap memory: top - 15:35:21 up 6 days, 3:23, 1 user, load average: 1.60, 1.43, 1.37 Tasks: 47 total, 2 running, 45 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 1.3%sy, 0.0%ni, 14.7%id, 83.8%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 3928924k total, 2855572k used, 1073352k free, 640564k buffers Swap: 0k total, 0k used, 0k free, 1887788k cached swapon -s doesn't seem to think there's any swap space: Filename Type Size Used Priority free -m doesn't think there's any swap either: total used free shared buffers cached Mem: 3836 3663 172 0 626 2701 -/+ buffers/cache: 336 3500 Swap: 0 0 0 And neither does vmstat: procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 3 0 66224 641372 2874744 0 0 21 5012 21 33 2 2 76 19 But cat /etc/fstab thinks there is a swap partition: /dev/xvda1 / ext3 defaults 1 1 /dev/xvda2 /mnt ext3 defaults 0 0 /dev/xvda3 swap swap defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 However df -k gives no indication of the xvda3 partition: Filesystem 1K-blocks Used Available Use% Mounted on /dev/xvda1 16513960 15675324 0 100% / tmpfs 1964460 8 1964452 1% /lib/init/rw udev 1914148 28 1914120 1% /dev tmpfs 1964460 4 1964456 1% /dev/shm So I really don't know what to make of this, because I appear to have a process using about 10 times more virtual memory than what might be available, and I have no idea where this virtual memory is on the system. I'm probably misinterpreting the output of the tools, so I'd be grateful if someone would be able to set me straight: What have I got wrong, what's the right interpretation, and how do you reach that interpretation? EDIT0: We use 10gen's MMS for monitoring the database, the relevant section for memory from the last data point is: "mem": { "virtual": 20749, "bits": 64, "supported": true, "mappedWithJournal": 20376, "mapped": 10188, "resident": 1219 }, This JSON is specific to the database process (I believe) rather than the system as a whole. fdisk -l /dev/xvda outputs... nothing? I tried each of the 3 xvda entries in /etc/fstab as well: root@ip:~# fdisk -l /dev/xvda1 Disk /dev/xvda1: 34.4 GB, 34359738368 bytes 255 heads, 63 sectors/track, 4177 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/xvda1 doesn't contain a valid partition table root@ip:~# fdisk -l /dev/xvda2 root@ip:~# fdisk -l /dev/xvda3 root@ip:~# Edit1: Output of cat /proc/meminfo for the sake of completeness: MemTotal: 3928924 kB MemFree: 726600 kB Buffers: 648368 kB Cached: 2216556 kB SwapCached: 0 kB Active: 1945100 kB Inactive: 994016 kB Active(anon): 60476 kB Inactive(anon): 12952 kB Active(file): 1884624 kB Inactive(file): 981064 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 387180 kB Writeback: 0 kB AnonPages: 73380 kB Mapped: 1188260 kB Shmem: 48 kB Slab: 149768 kB SReclaimable: 146076 kB SUnreclaim: 3692 kB KernelStack: 1104 kB PageTables: 16096 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 1964460 kB Committed_AS: 305572 kB VmallocTotal: 34359738367 kB VmallocUsed: 16760 kB VmallocChunk: 34359721448 kB HardwareCorrupted: 0 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 3932160 kB DirectMap2M: 0 kB

  Read the article

• Logging to MySQL without empty rows/skipped records?

  - by Lee Ward

  I'm trying to figure out how to make Squid proxy log to MySQL. I know ACL order is pretty important but I'm not sure if I understand exactly what ACLs are or do, it's difficult to explain, but hopefully you'll see where I'm going with this as you read! I have created the lines to make Squid interact with a helper in squid.conf as follows: external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log The external ACL helper (mysql_lg.php) is a PHP script and is as follows: error_reporting(0); if (! defined(STDIN)) { define("STDIN", fopen("php://stdin", "r")); } $res = mysql_connect('localhost', 'squid', 'testsquidpw'); $dbres = mysql_select_db('squid', $res); while (!feof(STDIN)) { $line = trim(fgets(STDIN)); $fields = explode(' ', $line); $user = rawurldecode($fields[0]); $cli_ip = rawurldecode($fields[1]); $protocol = rawurldecode($fields[2]); $uri = rawurldecode($fields[3]); $q = "INSERT INTO logs (id, user, cli_ip, protocol, url) VALUES ('', '".$user."', '".$cli_ip."', '".$protocol."', '".$uri."');"; mysql_query($q) or die (mysql_error()); if ($fault) { fwrite(STDOUT, "ERR\n"); }; fwrite(STDOUT, "OK\n"); } The configuration I have right now looks like this: ## Authentication Handler auth_param ntlm program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 30 auth_param negotiate program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-basic auth_param negotiate children 5 # Allow squid to update log external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log acl localnet src 172.16.45.0/24 acl AuthorizedUsers proxy_auth REQUIRED acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl CONNECT method CONNECT acl blockeddomain url_regex "/etc/squid3/bl.acl" http_access deny blockeddomain deny_info ERR_BAD_GENERAL blockeddomain # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # Allow the internal network access to this proxy http_access allow localnet # Allow authorized users access to this proxy http_access allow AuthorizedUsers # FINAL RULE - Deny all other access to this proxy http_access deny all From testing, the closer to the bottom I place the logging lines the less it logs. Oftentimes, it even places empty rows in to the MySQL table. The file-based logs in /var/log/squid3/access.log are correct but many of the rows in the access logs are missing from the MySQL logs. I can't help but think it's down to the order I'm putting lines in because I want to log everything to MySQL, unauthenticated requests, blocked requests, which category blocked a specific request. The reason I want this in MySQL is because I'm trying to have everything managed via a custom web-based frontend and want to avoid using any shell commands and access to system log files if I can help it. The end result is to make it as easy as possible to maintain without keeping staff waiting on the phone whilst I add a new rule and reload the server! Hopefully someone can help me out here because this is very much a learning experience for me and I'm pretty stumped. Many thanks in advance for any help!

  Read the article

• Weird Network Behavior of Home Router

  - by Stilgar

  First of all I would like to apologize because what you are going to read will be long and confusing but I am fighting this issue for 3 days now and am out of ideas. At home I have the following setup 50Mbps Internet connects into a home router A 2 desktop computers connect to router A via standard FTP LAN cables including one where the cable is ~20m long. a second router B connects to router A via standard FTP LAN cable X (~20m long). several devices connect to the wireless network of router B and there are a couple of desktop computers connected to it through FTP LAN cables. For some reason computers connected to router B when it is connected via cable X have very slow Internet connection. It is like 5 times slower than what is expected. This is the actual problem I am trying to solve. Interesting facts If a computer is connected to cable X directly instead of through router B the Internet speed is just fine (up to the 50Mbps I get from the ISP). Tested with two computers. I have tried replacing router B with another router C and the problem persists. If I connect router B via another cable to the same ports with the same settings everything seems to work fine and computers connected to router B have quite fast Internet I have tested mainly via Speedtest.net but I have also achieved similar speeds when downloading a file The upload speed is quite higher than the download speed in all cases. Note that my ISP usually has higher upload speed (unless it manages to hit the 50Mbps cap) It seems like the speed when connecting through router B with cable X is reduced 4-5 times no matter what the original speed is. For example via router B I get 10Mbps speed to local servers where I get 50Mbps when connected on router A. If I use a distant server where the ISP is only able to provide 25Mbps I get 4-5Mbps on router B. WiFi is slower than LAN on both routers (which is normal) but the reduced speed is reduced proportionally for WiFi. In addition the upload speed is normally higher from the ISP and it is also reduced proportionally. I have tried two different network configurations. One where I have NAT behind NAT where router B connects to router A via the WAN port and has its own DHCP. Second where router B connects to router A via standard LAN port and has DHCP disabled. In this configuration router B serves as a switch and the Network Gateway for computers connected to router B is the internal IP address of router A. Both configurations work just fine but both manifest the reduced speed issue. pings seem to work just fine As far as I can tell none of the cables is crossed The RJ45 setup for cable X orange orange-white brown brow-white blue blue-white green green-white This is a big problem for me since cable X passes through walls and floors and is very hard to replace. I also may have gotten some of the facts wrong because I am almost going crazy with this issue and testing includes going several floors up and down the staircase. One hypothesis I came up with is that the cable is defective in such a way that the voltage from the router affects its performance. When it is connected to a computer it performs just fine but the router has less power. Related hypothesis includes the cable being affected by electricity cables in the walls when the voltage is low. (I know nothing about electricity) So any ideas what to do, what to test or what the issue may be?

  Read the article

• mod evasive not working properly on ubuntu 10.04

  - by Joe Hopfgartner

  I have an ubuntu 10.04 server where I installed mod_evasive using apt-get install libapache2-mod-evasive I already tried several configurations, the result stays the same. The blocking does work, but randomly. I tried with low limis and long blocking periods as well as short limits. The behaviour I expect is that I can request websites until either page or site limit is reached per given interval. After that I expect to be blocked until I did not make another request for as long as the block period. However the behaviour is that I can request sites and after a while I get random 403 blocks, which increase and decrase in percentage, however they are very scattered. This is an output of siege, so you get an idea: HTTP/1.1 200 0.09 secs: 75 bytes ==> /robots.txt HTTP/1.1 403 0.08 secs: 242 bytes ==> /robots.txt HTTP/1.1 200 0.08 secs: 75 bytes ==> /robots.txt HTTP/1.1 403 0.08 secs: 242 bytes ==> /robots.txt HTTP/1.1 200 0.11 secs: 75 bytes ==> /robots.txt HTTP/1.1 403 0.08 secs: 242 bytes ==> /robots.txt HTTP/1.1 200 0.08 secs: 75 bytes ==> /robots.txt HTTP/1.1 403 0.09 secs: 242 bytes ==> /robots.txt HTTP/1.1 200 0.08 secs: 75 bytes ==> /robots.txt HTTP/1.1 200 0.09 secs: 75 bytes ==> /robots.txt HTTP/1.1 200 0.08 secs: 75 bytes ==> /robots.txt HTTP/1.1 200 0.09 secs: 75 bytes ==> /robots.txt HTTP/1.1 403 0.08 secs: 242 bytes ==> /robots.txt HTTP/1.1 200 0.08 secs: 75 bytes ==> /robots.txt HTTP/1.1 403 0.08 secs: 242 bytes ==> /robots.txt HTTP/1.1 200 0.10 secs: 75 bytes ==> /robots.txt HTTP/1.1 403 0.08 secs: 242 bytes ==> /robots.txt HTTP/1.1 200 0.08 secs: 75 bytes ==> /robots.txt HTTP/1.1 403 0.09 secs: 242 bytes ==> /robots.txt HTTP/1.1 200 0.10 secs: 75 bytes ==> /robots.txt HTTP/1.1 403 0.09 secs: 242 bytes ==> /robots.txt HTTP/1.1 200 0.09 secs: 75 bytes ==> /robots.txt HTTP/1.1 200 0.08 secs: 75 bytes ==> /robots.txt HTTP/1.1 200 0.09 secs: 75 bytes ==> /robots.txt HTTP/1.1 200 0.08 secs: 75 bytes ==> /robots.txt HTTP/1.1 200 0.10 secs: 75 bytes ==> /robots.txt HTTP/1.1 200 0.08 secs: 75 bytes ==> /robots.txt The exac limits in place during this test run were: DOSHashTableSize 3097 DOSPageCount 10 DOSSiteCount 100 DOSPageInterval 10 DOSSiteInterval 10 DOSBlockingPeriod 120 DOSLogDir /var/log/mod_evasive DOSEmailNotify ***@gmail.com DOSWhitelist 127.0.0.1 So I would expect to be blocked at least 120 seconds after being blocked once. Any ideas aobut this? I also tried adding my configuration at different places (vhost, server config, directory context) and with of without ifmodule directive... This doesnt change anything.

  Read the article

• Nginx error page with JSON response

  - by Waseem

  I'm trying to serve a maintenance page to clients making request to my application when it is under maintenance. Following is my nginx configuration for that purpose. server { recursive_error_pages on; listen 80; ... if (-f $document_root/maintenance.html) { return 503; } error_page 404 /404.html; error_page 500 502 504 /500.html; error_page 503 @503; location = /404.html { root $document_root; } location = /500.html { root $document_root; } location @503 { error_page 405 =/maintenance.html; if (-f $request_filename) { break; } rewrite ^(.*)$ /maintenance.html break; } } Lets say I have enabled maintenance of my site by creating a $document_root/maintenance.html. This file, correctly, is served when a user makes a request with with Accept header of text/html. $ curl http://server.com/ -i -v -X GET -H "Accept: text/html" * Adding handle: conn: 0xf89420 * Adding handle: send: 0 * Adding handle: recv: 0 * Curl_addHandleToPipeline: length: 1 * - Conn 0 (0xf89420) send_pipe: 1, recv_pipe: 0 * About to connect() to server.com port 80 (#0) * Trying xxx.xxx.xxx.xxx... * Connected to server.com (xxx.xxx.xxx.xxx) port 80 (#0) > GET / HTTP/1.1 > User-Agent: curl/7.33.0 > Host: server.com > Accept: text/html > < HTTP/1.1 503 Service Temporarily Unavailable HTTP/1.1 503 Service Temporarily Unavailable * Server nginx/1.1.19 is not blacklisted < Server: nginx/1.1.19 Server: nginx/1.1.19 < Date: Thu, 14 Nov 2013 11:16:16 GMT Date: Thu, 14 Nov 2013 11:16:16 GMT < Content-Type: text/html Content-Type: text/html < Content-Length: 27 Content-Length: 27 < Connection: keep-alive Connection: keep-alive < This is under maintenance. * Connection #0 to host server.com left intact Now some clients set Accept header to application/json. How do I send them a JSON response instead of maintenance.html? Following is the response that I get when setting Accept to application/json. $ curl http://server.com/ -i -v -X GET -H "Accept: application/json" * Adding handle: conn: 0x190c430 * Adding handle: send: 0 * Adding handle: recv: 0 * Curl_addHandleToPipeline: length: 1 * - Conn 0 (0x190c430) send_pipe: 1, recv_pipe: 0 * About to connect() to server.com port 80 (#0) * Trying xxx.xxx.xxx.xxx... * Connected to server.com (xxx.xxx.xxx.xxx) port 80 (#0) > GET / HTTP/1.1 > User-Agent: curl/7.33.0 > Host: server.com > Accept: application/json > < HTTP/1.1 503 Service Temporarily Unavailable HTTP/1.1 503 Service Temporarily Unavailable * Server nginx/1.1.19 is not blacklisted < Server: nginx/1.1.19 Server: nginx/1.1.19 < Date: Thu, 14 Nov 2013 11:15:50 GMT Date: Thu, 14 Nov 2013 11:15:50 GMT < Content-Type: text/html Content-Type: text/html < Content-Length: 27 Content-Length: 27 < Connection: keep-alive Connection: keep-alive < This is under maintenance. * Connection #0 to host server.com left intact

  Read the article

• SSH-forwarded X11 display from Linux to Mac lost after some time

  - by mklein9

  I have a new and vexing problem with ssh forwarding my X11 connection when logging in from a Mac (10.7.2) to Linux (Ubuntu 8.04). I have no trouble using ssh -X to log in to the remote machine and starting an X11-based application from that shell. What has recently started happening is that additional invocations of X11 applications from that same shell, after a while (on the order of hours), are unable to start because the forwarded display is being blocked (I presume). When attempting to start xterm, for example, I get the usual message about a bad DISPLAY setting, such as: xterm Xt error: Can't open display: localhost:10.0 But the X11 application I started right when I logged in is still running along just fine, using that exact same display (localhost:10.0), just that it was started earlier. I turned on verbose logging in sshd_config and I see this in the /var/log/auth.log file in response to the failed xterm startup attempt: sshd[22104]: channel 8: open failed: administratively prohibited: open failed If I ssh -X to the server again, starting a new shell and getting assigned a new display (localhost:11.0), the same process repeats: the X11 applications started early on run just fine for as long as I keep them open (days), but after a few hours I cannot start any new ones from that shell. Particulars: OpenSSH sshd server running on Ubuntu 8.04, display forwarded to a Mac running Lion (10.7.2) with the default Apple X server. The systems are connected on an Ethernet LAN with a single switch between them. Neither machine is running a firewall. Until recently (a few days ago) this setup worked perfectly so I am mystified as to where to look next. I am by no means an X11 or SSH expert but have good UNIX/Linux experience. Nothing obvious has changed in either client or server configuration although I have tried changing a few options to try to debug this, like setting sshd_config's TCPKeepAlive to no, and setting "host +localhost" (you can tell I've been Googling). When logging in from a Linux 11.10 laptop to the same remote host over the same network and switch, this problem does not occur -- an xterm can be invoked successfully hours later from the same ssh login shell while the same experiment from the Mac fails (tested this morning to be sure), so it would appear to be a Mac-specific issue. With "LogLevel DEBUG3" set on the remote machine (sshd server), and no change made in the client connections by me, /var/log/auth.log shows one slight change in connection status reports overnight, which is the port number used by the one successful ssh session from the Linux machine (I think), connection #7 below: sshd[20173]: debug3: channel 7: status: The following connections are open:\r\n #0 server-session (t4 r0 i0/0 o0/0 fd 14/13 cfd -1)\r\n #3 X11 connection from 127.0.0.1 port 57564 (t4 r1 i0/0 o0/0 fd 16/16 cfd -1)\r\n #4 X11 connection from 127.0.0.1 port 57565 (t4 r2 i0/0 o0/0 fd 17/17 cfd -1)\r\n #5 X11 connection from 127.0.0.1 port 57566 (t4 r3 i0/0 o0/0 fd 18/18 cfd -1)\r\n #6 X11 connection from 127.0.0.1 port 57567 (t4 r4 i0/0 o0/0 fd 19/19 cfd -1)\r\n #7 X11 connection from 127.0.0.1 port 59007 In this report, everything is the same between status reports except the port number used by connection #7 which I believe is the Linux client -- the only one still maintaining a display connection. It continues to increment over time, judging by a sequence of these reports overnight. Thanks for any help, -Mike

  Read the article

• http.conf setup to simplify using 'localhost:81'

  - by Will

  I'm installing portable wampserver within my dropbox folder so I can access anywhere. I have this achieved and accessible using http://locahost:81 I want to access it by using a different address (dropping the :81 port number) such as http://myothersite. I'm fairly certain I need to add a virtualhosts directove somewhere within this, but I am not Apache experienced! This is the current Apache httpd.conf file: ServerRoot "C:/Users/will/Dropbox/Wampee-2.1-beta-2/bin/apache/apache2.2.17" Listen 81 ServerAdmin admin@localhost ServerName localhost:81 DocumentRoot "C:/Users/will/Dropbox/Wampee-2.1-beta-2/www/" <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> <Directory "C:/Users/will/Dropbox/Wampee-2.1-beta-2/www/"> Options Indexes FollowSymLinks AllowOverride all # onlineoffline tag - don't remove Order Deny,Allow Deny from all Allow from 127.0.0.1 </Directory> <IfModule dir_module> DirectoryIndex index.php index.php3 index.html index.htm </IfModule> <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> ErrorLog "C:/Users/will/Dropbox/Wampee-2.1-beta-2/logs/apache_error.log" LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog "C:/Users/will/Dropbox/Wampee-2.1-beta-2/logs/access.log" common #CustomLog "logs/access.log" combined </IfModule> <IfModule alias_module> ScriptAlias /cgi-bin/ "cgi-bin/" </IfModule> <IfModule cgid_module> #Scriptsock logs/cgisock </IfModule> <Directory "cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig conf/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddType application/x-httpd-php .php AddType application/x-httpd-php .php3 </IfModule> # Server-pool management (MPM specific) #Include conf/extra/httpd-mpm.conf # Multi-language error messages #Include conf/extra/httpd-multilang-errordoc.conf # Fancy directory listings Include conf/extra/httpd-autoindex.conf # Language settings #Include conf/extra/httpd-languages.conf # User home directories #Include conf/extra/httpd-userdir.conf # Real-time info on requests and configuration #Include conf/extra/httpd-info.conf # Virtual hosts #Include conf/extra/httpd-vhosts.conf # Local access to the Apache HTTP Server Manual #Include conf/extra/httpd-manual.conf # Distributed authoring and versioning (WebDAV) #Include conf/extra/httpd-dav.conf # Various default settings #Include conf/extra/httpd-default.conf # Secure (SSL/TLS) connections #Include conf/extra/httpd-ssl.conf # # Note: The following must must be present to support # starting without SSL on platforms with no /dev/random equivalent # but a statically compiled-in mod_ssl. # <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> Include "C:/Users/will/Dropbox/Wampee-2.1-beta-2/alias/*" Include "C:/Users/will/Dropbox/Wampee-2.1-beta-2/MyWebAp ps/etc/alias/*"

  Read the article

• Kernel panic when bringing up DRBD resource

  - by sc.

  I'm trying to set up two machines synchonizing with DRBD. The storage is setup as follows: PV - LVM - DRBD - CLVM - GFS2. DRBD is set up in dual primary mode. The first server is set up and running fine in primary mode. The drives on the first server have data on them. I've set up the second server and I'm trying to bring up the DRBD resources. I created all the base LVM's to match the first server. After initializing the resources with `` drbdadm create-md storage I'm bringing up the resources by issuing drbdadm up storage After issuing that command, I get a kernel panic and the server reboots in 30 seconds. Here's a screen capture. My configuration is as follows: OS: CentOS 6 uname -a Linux host.structuralcomponents.net 2.6.32-279.5.2.el6.x86_64 #1 SMP Fri Aug 24 01:07:11 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux rpm -qa | grep drbd kmod-drbd84-8.4.1-2.el6.elrepo.x86_64 drbd84-utils-8.4.1-2.el6.elrepo.x86_64 cat /etc/drbd.d/global_common.conf global { usage-count yes; # minor-count dialog-refresh disable-ip-verification } common { handlers { pri-on-incon-degr "/usr/lib/drbd/notify-pri-on-incon-degr.sh; /usr/lib/drbd/notify-emergency-reboot.sh; echo b /proc/sysrq-trigger ; reboot -f"; pri-lost-after-sb "/usr/lib/drbd/notify-pri-lost-after-sb.sh; /usr/lib/drbd/notify-emergency-reboot.sh; echo b /proc/sysrq-trigger ; reboot -f"; local-io-error "/usr/lib/drbd/notify-io-error.sh; /usr/lib/drbd/notify-emergency-shutdown.sh; echo o /proc/sysrq-trigger ; halt -f"; # fence-peer "/usr/lib/drbd/crm-fence-peer.sh"; # split-brain "/usr/lib/drbd/notify-split-brain.sh root"; # out-of-sync "/usr/lib/drbd/notify-out-of-sync.sh root"; # before-resync-target "/usr/lib/drbd/snapshot-resync-target-lvm.sh -p 15 -- -c 16k"; # after-resync-target /usr/lib/drbd/unsnapshot-resync-target-lvm.sh; } startup { # wfc-timeout degr-wfc-timeout outdated-wfc-timeout wait-after-sb become-primary-on both; wfc-timeout 30; degr-wfc-timeout 10; outdated-wfc-timeout 10; } options { # cpu-mask on-no-data-accessible } disk { # size max-bio-bvecs on-io-error fencing disk-barrier disk-flushes # disk-drain md-flushes resync-rate resync-after al-extents # c-plan-ahead c-delay-target c-fill-target c-max-rate # c-min-rate disk-timeout } net { # protocol timeout max-epoch-size max-buffers unplug-watermark # connect-int ping-int sndbuf-size rcvbuf-size ko-count # allow-two-primaries cram-hmac-alg shared-secret after-sb-0pri # after-sb-1pri after-sb-2pri always-asbp rr-conflict # ping-timeout data-integrity-alg tcp-cork on-congestion # congestion-fill congestion-extents csums-alg verify-alg # use-rle protocol C; allow-two-primaries yes; after-sb-0pri discard-zero-changes; after-sb-1pri discard-secondary; after-sb-2pri disconnect; } } cat /etc/drbd.d/storage.res resource storage { device /dev/drbd0; meta-disk internal; on host.structuralcomponents.net { address 10.10.1.120:7788; disk /dev/vg_storage/lv_storage; } on host2.structuralcomponents.net { address 10.10.1.121:7788; disk /dev/vg_storage/lv_storage; } /var/log/messages is not logging anything about the crash. I've been trying to find a cause of this but I've come up with nothing. Can anyone help me out? Thanks.

  Read the article

< Previous Page | 569 570 571 572 573 574 575 576 577 578 579 580  | Next Page >