Search Results

Search found 3061 results on 123 pages for 'interfaces'.

Page 58/123 | < Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >

• IP alias lost when changing main IP

  - by rmflow

  my /etc/network/interfaces: auto eth0 iface eth0 inet static address 192.168.3.75 netmask 255.255.255.0 gateway 192.168.3.0 Situation 1: After linux booted I set an IP alias: ifconfig eth0:0 192.168.3.111 Now ifconfig reports two IP addresses 192.168.3.75 at eth0 and 192.168.3.111 at eth0:0 When I change main IP to another network: ifconfig eth0 192.168.1.111 the alias eth0:0 is lost! Situation 2: After linux booted I set an IP alias: ifconfig eth0:0 192.168.4.111 Now ifconfig reports two IP addresses 192.168.3.75 at eth0 and 192.168.4.111 at eth0:0 When I change main IP to another network: ifconfig eth0 192.168.1.111 the alias eth0:0 stays! How do I properly change main IP, so all my aliases are not lost?

  Read the article

• correct routing for multiple devices

  - by helmi

  I have Debian Lenny machine with 3 interfaces enabled (eth0-2), and I have problems as follow. eth1 is connected to a router and this router has portforwarding for port80. eth2 is connected direct to the internet If I open a website hosted on my system via the router it works fine. If I try to open the same via the eth2 connetion it does not! tshark shows incomming trafic on eth2 but nothing goes out there. iptabes accepts all My routing table: Ziel Router Genmask Flags Metric Ref Use Iface 10.9.0.2 * 255.255.255.255 UH 0 0 0 tun0 212.236.24.128 * 255.255.255.224 U 0 0 0 eth2 192.168.1.0 * 255.255.255.0 U 0 0 0 eth1 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 10.9.0.0 10.9.0.2 255.255.255.0 UG 0 0 0 tun0 default 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 default 212.236.024.129 0.0.0.0 UG 0 0 0 eth2 default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Red Hat cluster: Failure of one of two services sharing the same virtual IP tears down IP

  - by js01

  I'm creating a 2+1 failover cluster under Red Hat 5.5 with 4 services of which 2 have to run on the same node, sharing the same virtual IP address. One of the services on each node needs a (SAN) disk, the other doesn't. I'm using HA-LVM. When I shut down (via ifdown) the two interfaces connected to the SAN to simulate SAN failure, the service needing the disk is disabled, the other keeps running, as expected. Surprisingly (and unfortunately), the virtual IP address shared by the two services on the same machine is also removed, rendering the still-running service useless. How can I configure the cluster to keep the IP address up?

  Read the article

• How to prevent Ubuntu from combining networks on 2 NIC server?

  - by SolarPower

  I've got a Ubuntu Server 10.10 with 2 network interfaces with a cable plugged into both going to switches on completely different networks with different routers. One network is the 10.1.10.X network with a separate gateway/router - the server has an IP of 10.1.10.50 with the gateway IP of 10.1.10.1. The other interface is 10.2.10.X, IP 10.2.10.50, gateway 10.2.10.1. All my Mac machines are on the 10.2.10.X network, and all servers on the 10.1.10.X. The ONLY connection between the two is this machine. From a Mac in my office, I CANNOT ping any computer on the 10.1.10.X network except the Ubuntu machine I'm talking about. However, under the Shared column in Finder, I can see every server on the other network listed. That makes me believe that somehow this Ubuntu machine is letting certain requests span both networks, which is a security problem. Hope this is enough info.

  Read the article

• ifconfig ignores alias on IPv6

  - by Marten Lehmann

  When I add an IPv4 address for the interface eth0:0 with ifconfig, it is created correctly: ifconfig eth0:0 add 192.168.10.10 This can be verified by ifconfig or "ip a". When I add an IPv6 address however, ifconfig seems to ignore the alias of the interface: ifconfig eth0:0 add fc00::2/48 The address fc00::2/48 is added to eth0 then, not to eth0:0, no matter if eth0:0 previously exists with an IPv4 address or not. I'm doing this on CentOS 5 but I guess it is a general behaviour of ifconfig? Am I doing something wrong or is this by intention? I'm using separate aliases for interfaces very often and I hoped to use it for IPv6 as well. Kind regards Marten

  Read the article

• iptables forwarding between two interface

  - by broody

  So I have a linux box with two wireless interfaces, one is a station and the other an AP. wlan0 (station) - Connected to the internet connection wlan1 (AP) - Other clients connect to it. I would like for clients connected to wlan1 to be able to access the internet on wlan0. And I'd like to do this with iptables as my kernel doesn't have bridging support... Here's what I've tried so far with iptables but it's not working: iptables -A FORWARD -i wlan0 -o wlan1 -j ACCEPT iptables -A FORWARD -i wlan1 -o wlan0 -j ACCEPT I'd appreciate any help.

  Read the article

• Linux box acting as wireless access point to share the internet connection

  - by Suresh

  A linux machine is connected to internet over two interfaces ppp0 and ppp1 using two modems. Also this machine acts as wireless access point through an interface say, eth0 with ip address 192.168.1.1 and acts as gateway for the connected devices through this network with subnet mask 255.255.255.0 Now is it possible to achieve the following: When any of the connected devices through wireless AP needs internet connection linux machine has to use ppp1 interface for internet. If any of the applications on the linux machine needs internet connection linux machine should use ppp0 interface for the internet. Can this be achieved by adding rules to chains in filter/nat tables? If the kernel routing table has a default rule to route the default traffic through interface ppp0, wil kernel completely ignore ppp1 for internet? PS: new to networking and routing concepts, If the question is not clear leave a comment, will try to give more information.

  Read the article

• Linux: multiple network connections - 3G/4G / Wifi / LAN / etc; how can i set a preferred network connection to use?

  - by Alex

  I've been looking at how I can setup a laptop that has multiple network interfaces, but a problem exists if all the connections are active, i.e. 3G, WiFi and LAN are all connected, I would like it to default to LAN. I would like to set "weights" or "priority" to each connection, so that if the LAN is unplugged, it'll default to WiFi - if its in range and working, otherwise, it'll switch and use the 3G dongle; I've been looking around and I can see that the "metric" counter for route isn't being used for recent kernels. I thought that would be able to set the preferred gateway / connections - but according to the man page: man route: OUTPUT Metric The 'distance' to the target (usually counted in hops). It is not used by recent kernels, but may be needed by routing daemons. So I'm confused, are there any scripts / apps / anything that can detect active network connections, and by way of configuration, send my default gateway network traffic through that interface if its active / alive?

  Read the article

• How can I store Rails uploads on a remote server (and not a common cloud host)?

  - by joshee

  I would like to store uploads from a Rails application on a different server than my application server. I want to keep costs to a minimum and host this other server in-house. I am planning to use Carrierwave for uploads. It seems Carrierwave interfaces with Fog for remote hosts. Is there a way I could set the other server to act as a Fog provider? How would I go about this setup? Or, is there some better and easier way to go about all this?

  Read the article

• Linux does not communicate to Windows subinterface

  - by artaxerxe

  I set my NIC on Windows so that I have two interfaces: one (the first one) has IP 192.168.0.5 the other one has IP 10.10.10.1. On a Linux machine I set an interface to 10.10.10.2. On another Linux machine I set the interface to 10.10.10.3. And tried to ping those machines. Here is the result. Linux to Linux is ok. Windows to Linux also is ok. But Linux to Windows does not work. Can you help me on getting the communication between Linux and Windows? What should I do for this? I have to mention that those machines are connected through a switch. If you need any details, ask me please! Thanks in advance!

  Read the article

• openwrt uses a single interface bridge?

  - by timbo

  My understanding of bridging is that it ties together two interfaces at layer 2. I am looking at a Ubiquiti Nanostation2 running OpenWRT that has an ethernet port 'eth0' and a wifi port 'ath0'. The ethernet port (the 'wan' port) is not part of the bridge and the bridge is just a single interface. Can anyone clarify this? - seems very different to Ubuntu. /etc/config/network: config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' config 'interface' 'wifi' option 'ipaddr' '192.168.13.1' option 'type' 'bridge' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ifname' 'wifi0'

  Read the article

• Can I get dual monitor support (2xDVI) from my (DVI+HDMI) graphics card?

  - by nray

  It seems that pure 2 x DVI dual head video cards are becoming rare. Most cards feature something like 1 x DVI plus 1 x HDMI plus 1 x VGA or some other interface. The idea seems to be that you can just use an HDMI <= DVI adapter. One result is that cards are seldom marked " 2 x DVI " anymore, but does this mean that they support simultaneous output on all interfaces? Are all cards dual head these days? Take Asus's nVidia cards for example, they routinely have 1 x DVI plus 1 x HDMI instead of 2 x DVI, so my question is, are these equivalent to a dual head DVI card, or is there some detail required for dual monitor support? I use dual-monitor stretched desktops for digital signage projects.

  Read the article

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• PFSENSE and IPV6 , direct connect rules

  - by Bgnt44

  My question is about pfsense configuration for ipv6 In theory Ipv6 are fully routable even in a LAN For stating point i ve Using this tutorial : http://doc.pfsense.org/index.php/Using_IPv6_on_2.1_with_a_Tunnel_Broker So my Lan network has ipv4 connection and ipv6 I would like to be able to access my LAN machines by their IPV6 i'm confused with firewall rules which i need to set to be able to do that Even if i set all interfaces to pass all packets, i'm not able to directly access any machine by their IPV6 Did i miss something ? Edit : Ok i found that it work now, think it has always work but my isp seems to support ipv6 sometimes and sometimes not ... weird

  Read the article

• Using Ctrl-Tab to switch between tabs in Mac Terminal.app

  - by dkee

  How can I make Ctrl-Tab and Ctrl-Shift-Tab switch between tabs in Terminal.app on a Mac (OS 10.4 and 10.5 specifically)? This is how I switch tabs in Firefox and Aquamacs, and Command-Shift-[ and Command-Shift-] is too awkward to me. I am aware of this related question: .../unable-to-switch-a-tab-efficiently-in-macs-terminal* And hence the Keyboard Shortcuts section of the System Preferences, but the dialog box for Keyboard Shortcuts doesn't seem to accept Ctrl-Tab in the Keyboard Shortcut field. Is there a special keyboard sequence for inputting tabs (with modifiers) into a dialog box field on a Mac? Is there any other method that would allow me to customize Terminal.app in the way I desire? Not really a programming question, but I think the answer would be useful to other folks that program on Macs and would like to have some consistency between interfaces of different applications. Thanks! * Couldn't add the hyperlink as a new user

  Read the article

• Cisco asa 5505 locks up / unresponsive

  - by Chris

  We have a cisco asa 5505 that's new (in service for about 2 months) running 7.2(4) software. Every day around 10a it locks up for approx 10 minutes. We're monitoring it via snmp with stg, and snmp doesn't respond during that time. There's no output in the 'show crash' output. Internet connectivity is also dropped. Wondering if anyone else has seen this and what the fix might be. Currently we're looking at upgrading software, but will need memory upgrade for that. We've forced the speed and duplex on the internal and external interfaces, but the problem is still occurring. It's connected on the internal lan to a netgear 724 gige switch.

  Read the article

• Broadcast UDP over VPN

  - by ibmz

  I have OpenVPN configured and have 5 dd-wrt router clients. I would like the machines on those routers to be-able to UDP Broadcast across all 5 networks. I cannot bridge the interfaces(to my knowledge) because each router needs to be able to operate on its own should the VPN connection die (dhcp needs to work). currently each router has its own /24 (eg 192.168.1.x) network. Is there a way to use IPTables to mangle the udp and forward them to all VPN Clients? To summarize i need 1)to UDP broadcast to all routers and their clients 2)for all routers to be able to operate independently should the VPN go down

  Read the article

• Setting up a static IP address (public) in Ubuntu

  - by ycseattle

  I have a business class internet connection and need to setup a static ip address for a machine. I did a search online and only find how to setup static local ip addresses (like 192.168..). I tried the same technique, and only setup the ip address and netmask, but after restart networking the computer could not connect to the outside world. This is what I did: 1) edit /etc/network/interfaces iface eth0 inet static address 173.10.xxx.xx netmask 255.255.255.252 2) edit /etc/resolv.conf search wp.comcast.net nameserver xx.xx.xx.xxx nameserver xx.xx.xx.xxx 3) restart network sudo /etc/init.d/networking restart Now the last step didn't report error, ifconfig shows the ip address was set, but this server cannot connect to outside world, ping google.com and reports "unknown host google.com". Any ideas?

  Read the article

• How to set the preferred network interface in linux

  - by Mike Cooper

  I have my network set up like this. http://docs.google.com/Doc?docid=0AZ1YxuLE4djaZGhqN2s1NmRfMjhjNjc0Ym1meg&hl=en In words: I have a machine (Calcium, running Arch Linux) that has two network interfaces. eth0 is hoooked up to a router, and is gigabit. Eth1 is hooked up directly to the university network over 10Megabit. The router's uplink is hooked up to the university network as well, and it is also 10Megabit. Currently (I believe) all traffic on Calcium is going through eth0, through the router, regardless of whether it is internal or external. (How can I confirm this?) Ideally, traffic that is destined for the internal network (192.168.10.0/24) would travel over eth0 to the router, and wherever it is going. ALL other traffic should go over eth1.

  Read the article

• Windows Server - Dual NIC Bandwidth Pooling

  - by tsilb

  I have a Windows Server 2008 machine with dual NICs. Both are plugged into the same switch in a typical one-switch, one-gateway home network. This server is used almost exclusively for inbound connections. It hosts a web server (IIS 6), SQL server, and file server (via LAN UNC paths and mapped drives). How do I make best use of inbound bandwidth across both NICs? For example, if I connect to it by hostname and one of the interfaces has high traffic, I'd like the new connection to use the other interface.

  Read the article

• Confusion about HSRP Groups

  - by Kyle Brandt

  If I have a router that has several LANs on it, and each of these LAN is attached to a second router, do I need to use different HSRP groups for each LAN? With this set up, each virtual gateway will be on a Layer 2 segment. And within a router, no interface will have multiple gateways. So, For example: Router 1: F0/0: ip address 192.168.1.2 255.255.255.0 standby ip 192.168.1.1 F2/0: ip address 192.168.2.2 255.255.255.0 standby ip 192.168.2.1 Router 2: F0/0: ip address 192.168.1.3 255.255.255.0 standby ip 192.168.1.1 F2/0: ip address 192.168.2.3 255.255.255.0 standby ip 192.168.2.1 Will this work, or do I need standby 1 ip 192.168.2.1 on the F2/0 interfaces? Since according to the RFC, the group number of the packet is in the HSRP multicast packets, my guess is that I don't need different groups, and that multiple groups are only needed when they are all on the same Layer 2 segment. However, I haven't been able to find this setup....

  Read the article

• Multiple External IP Ranges on a Juniper SSG5

  - by Sam

  I have a Juniper SSG 5 firewall in a datacenter. The first interface (eth0/0) has been assigned a static IP address and has three other addresses configured for VIP Nat. I have a static route configured at the lowest priority for 0.0.0.0/0 to my hosting company's gateway. Now I need to configure a second IP block. I have the IPs assigned to the second interface (eth0/1) which is in the same security zone and virtual router as the first. However, with this interface enabled I (a) can't initiate outbound sessions (browse the internet, ping, DNS lookup, etc) even though I can access servers behind the firewall just fine from the outside and (b) can't ping the management IP of the firewall/gateway. I've tried anything I can think of but I guess this is a little above my head. Could anyone point me in the right direction? Interfaces: ethernet0/0 xxx.xxx.242.4/29 Untrust Layer3 ethernet0/1 xxx.xxx.152.0/28 Untrust Layer3 Routes: http://i.stack.imgur.com/60s41.png

  Read the article

• Proper way for changing MAC address in a linux VM?

  - by HappyDeveloper

  I tried to change the MAC address in a ubuntu VM (virtualbox), but after that it threw lots of errors during boot, and then I had no internet connection. Then I saw that the interface was renamed to eth1, so I edited /etc/network/interfaces to change eth0 to eth1, rebooted (didn't know how to restart the network), and boot was now faster and internet worked fine. But now after every time I log in, I get 1 or 2 error messages that say nothing, they only ask me if I want to report them. So I was wondering, is there was a proper way to change MAC address, to avoid these issues?

  Read the article

• Decrease the height of title bar in Visual Studio 2012 on secondary screen

  - by matcheek

  I have two screens on my VS2012. No problems with title bar on the main screen, on the secondary however, the title bar takes up lots of space - see screenshot attached. In VS2010, for example, the title bar on secondary screen is a lot thinier. I guess this change was made to address touch interfaces (??) but it is highly inconvenient to waste some much space just because of that. Anybody knows how the change just the height of the title bar on the secondary screen?

  Read the article

• SQL Server 2008 is not accessible from Windows Server 2008 ?

  - by Albert Widjaja

  Hi, I have successfully configured Windows Server 2008 Enterprise SP2 with SQL Server 2008 Enterprise SP2 all 64 bit, however when I tried to access this particular SQL Server 2008 DB instance from another SQL Server 2008 SSMS in another Windows Server 2008 it failed ? what I did is to disabled the IPv6 IP address using the regedit but still the problem hasn't been fixed even after restart ? I have enabled the named piped as well but still no luck ? any help please ? Here's the error message: " A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) "

  Read the article

< Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >