Search Results

Search found 1575 results on 63 pages for 'lts'.

Page 58/63 | < Previous Page | 54 55 56 57 58 59 60 61 62 63  | Next Page >

• How to find the reason for a weekly downtime on an Ubuntu web server hosted by AWS?

  - by IceSheep

  We started monitoring our web server using Pingdom and found out that we have a downtime of a few minutes every Sunday at 0:00 UTC. The test runs every minute and checks if a successful HTTP response (code 200) is returned on port 80. The test fails due to a timeout (no response after 30 seconds). Here's what we've already checked – without success: Since we run our webserver behind a load balancer, I've set the Pingdom test on the load balancer's public DNS and the webserver's public DNS in order to find out if there's a problem with the AWS load balancer – both tests return the same result We set up Munin on our webserver. Everything looked fine even after the failure. Since the last failure lasted only 2 minutes I suppose Munin couldn't capture a potential problem (it only checks every 5 minutes) I have checked /var/log/apache2/error.log and /var/log/syslog for suspicious entries I have checked /etc/cron.weekly and /etc/crontab for suspicious entries I have searched for files created or last-modified during 0:00 and 0:15 using this method: touch -t 201209020000 start touch -t 201209020015 end find / -newer start -and ! -newer end (nothing found) Has anybody experienced a similar problem? Any proposals on how to find the reason for this behavior? It's Ubuntu 10.04 LTS running on an AWS m1.large instance. Thanks!

  Read the article

• Route all traffic of home network through VPN [migrated]

  - by user436118

  I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

  Read the article

• Grub Autostart with timeout

  - by BetaRide

  On Ubuntu 10.4 LTS I want Grub to start the default OS after 5 Seconds. I'd like to see the output of the startup scripts. Currently grub wait forever until I hit return and the output of the startup scripts isn't visible. Can someone tell me how I have to configure /etc/default/grub or any other setups? I tried to play with GRUB_TIMEOUT and GRUB_DEFAULT and did a sudo update-grub afterwards, but nothing changed. Any ideas? # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. GRUB_DEFAULT=0 GRUB_HIDDEN_TIMEOUT=5 #GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=5 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" GRUB_SAVEDEFAULT=true # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux # GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_LINUX_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1"

  Read the article

• Multiple SSL certificates on one server

  - by Kyle O'Brien

  We're hosting two websites on our fairly tiny but dedicated production server. Both website require SSL authentication. So, we have virtualhosts set up for both of them. They both reference their own domain.key, domain.crt and domain.intermediate.crt files. Each CSR and certificate file for each site was setup using its own unique information and nothing is shared between them (other than the server itself) However, which ever site's symbolic link (set up in /etc/apache2/sites-enabled) is reference first, is the site who's certificate is referenced even if we're visiting the second site. So for example, assume our companies are Cadbury and Nestle. We set up both sites with their own certificates but we create Cadbury's symbolic link in apache's site-enabled folder first and then Nestle's. You can visit Nestle perfectly fine but if you check the certificate installation, it reference's Cadbury's certificate. We're hosting these websites on a dedicated Ubuntu 12.04.3 LTS server. Both certificates are provided by Thawte.com. I came across a few potential solutions with no degree of success. I'm hoping someone else has a decent solution? Thanks Edit: The only other solution that seems to have provided success to some people is using SNI with Apache. However, the setups here didn't seem to coincide with our setup at all.

  Read the article

• file system damage

  - by jffrs

  I try recover the backup superblock on /dev/sda2 that contain ubuntu 12.04 LTS and partition ext4 with livecd ubuntu 10.04. the message is below root@ubuntu:/home/ubuntu# fsck.ext4 -b 163840 -B 4096 /dev/sda2 e2fsck 1.41.11 (14-Mar-2010) /dev/sda2 was not cleanly unmounted, check forced. Resize inode not valid. Recreate? yes Pass 1: Checking inodes, blocks, and sizes Programming error? block #7963637 claimed for no reason in process_bad_block. Programming error? block #11240437 claimed for no reason in process_bad_block. Root inode is not a directory. Clear? yes Inode 712 is in extent format, but superblock is missing EXTENTS feature Fix? yes Inode 98519 has compression flag set on filesystem without compression support. Clear? yes Inode 98519 has INDEX_FL flag set but is not a directory. Clear HTree index? what's the correct procedure?

  Read the article

• ionice without effect

  - by tim

  System is Ubuntu 10 LTS 64bit (2.6.35.31), I'm running on xen 4.0, no services active, cron stopped, scheduler is cfq for the disk /usr is mounted from: time find /usr -exec stat {} \; > /dev/null 2>&1 & giving real 0m35.760s user 0m0.270s sys 0m3.910s and time ionice -c3 find /usr -exec stat {} \; > /dev/null 2>&1 & giving real 0m36.110s user 0m0.310s sys 0m4.100s which is exactly as expected, now I run both at the same time: time find /usr -exec stat {} \; > /dev/null 2>&1 & time ionice -c3 find /usr -exec stat {} \; > /dev/null 2>&1 & where to my believe the ioniced version should be much slower while the straight version should be as fast as if running alone. but: straight: real 1m10.430s user 0m0.320s sys 0m3.940s ioniced: real 1m10.230s user 0m0.250s sys 0m4.020s which implies that ionice did not work at all. Any hints?

  Read the article

• How to detect and configure an output with xrandr?

  - by ysap

  I have a DELL U2410 monitor connected to a Compaq 100B desktop equipped with an integrated AMD/ATI graphics card (AMD E-350). The installed O/S is Ubuntu 10.04 LTS. The computer is connected to the monitor via the DVI connection. The problem is that I cannot set the desktop resolution to the native 1920x1200. The maximum allowed resolution is 1600x1200. Doing some research I found about the xrandr utility. Unfortunately, when trying to use it I cannot configure it to the required resolution. First, it does not report the output name (which supposed to be DVI-0), saying default instead. Without it I cannot use the --fb option. The EDID utility seems to identify the monitor well. Here's the output from get-edid: # EDID version 1 revision 3 Section "Monitor" # Block type: 2:0 3:ff # Block type: 2:0 3:fc Identifier "DELL U2410" VendorName "DEL" ModelName "DELL U2410" # Block type: 2:0 3:ff # Block type: 2:0 3:fc # Block type: 2:0 3:fd HorizSync 30-81 VertRefresh 56-76 # Max dot clock (video bandwidth) 170 MHz # DPMS capabilities: Active off:yes Suspend:yes Standby:yes Mode "1920x1200" # vfreq 59.950Hz, hfreq 74.038kHz DotClock 154.000000 HTimings 1920 1968 2000 2080 VTimings 1200 1203 1209 1235 Flags "-HSync" "+VSync" EndMode # Block type: 2:0 3:ff # Block type: 2:0 3:fc # Block type: 2:0 3:fd EndSection but the xrandr -q command returns: Screen 0: minimum 640 x 400, current 1600 x 1200, maximum 1600 x 1200 default connected 1600x1200+0+0 0mm x 0mm 1600x1200 0.0* 1280x1024 0.0 1152x864 0.0 1024x768 0.0 800x600 0.0 640x480 0.0 720x400 0.0 When I try to set the resolution, I get: $ xrandr --fb 1920x1200 xrandr: screen cannot be larger than 1600x1200 (desired size 1920x1200) $ xrandr --output DVI-0 --auto warning: output DVI-0 not found; ignoring How can I set the screen resolution to 1920x1200? Why doesn't xrandr identify the DVI-0 output? Note that the same computer running Ubuntu version higher than 10.04 detects the correct resolution with no problems. On this machine I cannot upgrade due to some legacy hardware compatibility problems. Also, I don't see any optional screen drivers available in the Hardware Drivers dialog. ---- UPDATE: following the answer to this question, I got some advance. Now the required mode is listed in the xrandr -q list, but I can't switch to that mode. Using the Monitors applet (which now shows the new mode), I get the response that: The selected configuration for displays could not be applied. Could not set the configuration to CRTC 262. From the command line it looks like this: $ cvt 1920 1200 60 # 1920x1200 59.88 Hz (CVT 2.30MA) hsync: 74.56 kHz; pclk: 193.25 MHz Modeline "1920x1200_60.00" 193.25 1920 2056 2256 2592 1200 1203 1209 1245 -hsync +vsync $ xrandr --newmode "1920x1200_60.00" 193.25 1920 2056 2256 2592 1200 1203 1209 1245 -hsync +vsync $ xrandr -q Screen 0: minimum 640 x 400, current 1600 x 1200, maximum 1600 x 1200 default connected 1600x1200+0+0 0mm x 0mm 1600x1200 0.0* 1280x1024 0.0 1152x864 0.0 1024x768 0.0 800x600 0.0 640x480 0.0 720x400 0.0 1920x1200_60.00 (0x120) 193.0MHz h: width 1920 start 2056 end 2256 total 2592 skew 0 clock 74.5KHz v: height 1200 start 1203 end 1209 total 1245 clock 59.8Hz $ xrandr --addmode default 1920x1200_60.00 $ xrandr -q Screen 0: minimum 640 x 400, current 1600 x 1200, maximum 1600 x 1200 default connected 1600x1200+0+0 0mm x 0mm 1600x1200 0.0* 1280x1024 0.0 1152x864 0.0 1024x768 0.0 800x600 0.0 640x480 0.0 720x400 0.0 1920x1200_60.00 59.8 $ xrandr --output default --mode 1920x1200_60.00 xrandr: Configure crtc 0 failed Another piece of info (if it helps anyone): $ sudo lshw -c video *-display UNCLAIMED description: VGA compatible controller product: ATI Technologies Inc vendor: ATI Technologies Inc physical id: 1 bus info: pci@0000:00:01.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: latency=0 resources: memory:c0000000-cfffffff(prefetchable) ioport:f000(size=256) memory:feb00000-feb3ffff

  Read the article

• Installation problem Ubuntu 12.04 Crashing hardware error

  - by user93640

  I am running on Ubuntu 8.04 for quite some time without many problems. About almost a year ago or so I have been trying to upgrade to 10.04 LTS, but without any success. Each time when trying to upgrade or even newly install the installation process crashed after about an hour or so (I forgot exactly how long). Now I wanted to try Ubuntu 12.04 (not even installing, but I only selected "Try Ubuntu without installing") and I got similar errors. I did not try to install it, because of earlier experience with 10.04 when after I also lost 8.04 and had to install from scratch again (after which it worked). I get the following screen (as I am not allowed to upload photos here the text): 26.767262] [Hardware Error]: CPU 0: Machine Check Exception: 0 Bank 5: b200001804000e0f 26.767279] [Hardware Error]: TSC 0 26.767287] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017924 SOCKET 0 APIC 0 microcode 44 26.767297] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767307] [Hardware Error]: CPU 1: Machine Check Exception: 0 Bank 1: b200000000000175 26.767316] [Hardware Error]: TSC 0 26.767323] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017924 SOCKET 0 APIC 1 microcode 44 26.767331] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767339] [Hardware Error]: CPU 1: Machine Check Exception: 0 Bank 5: b200003000000e0f 26.767348] [Hardware Error]: TSC 0 26.767354] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017924 SOCKET 0 APIC 1 microcode 44 26.767363] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767371] [Hardware Error]: CPU 1: Machine Check Exception: 4 Bank 1: b200000000000175 26.767379] [Hardware Error]: TSC 1bf231e65f 26.767386] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017951 SOCKET 0 APIC 1 microcode 44 26.767395] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767403] [Hardware Error]: CPU 1: Machine Check Exception: 4 Bank 5: b200003008000e0f 26.767413] [Hardware Error]: TSC 1bf231e65f 26.767421] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017951 SOCKET 0 APIC 1 microcode 44 26.767429] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767437] [Hardware Error]: CPU 0: Machine Check Exception: 5 Bank 5: b200001806000e0f 26.767447] [Hardware Error]: RIP |INEXACT| 60:<00000000c1018b5c> {mwait_idle+0x7c/0x1d0} 26.767464] [Hardware Error]: TSC 1bf231e674 26.767471] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017951 SOCKET 0 APIC 0 microcode 44 26.767480] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767487] [Hardware Error]: Machine check: Processor context corrupt 26.767495] Kernel panic - not syncing: Fatal Machine check 26.767505] Pid: 579, comm: debconf-communi Tainted: G M 3.2.0.29-generic-pae #46-Ubuntu 26.767515] Call Trace: 26.767525] [<c158f812>] ? printk+0x2d/0x2f 26.767534] [<c158f6e0>] panic+0x5c/0x161 26.767542] [<c10247ef>] mce_panic.part.14+0x13f/0x170 26.767551] [<c1024872>] mce_panic+0x52/0x90 26.767558] [<c1024a18>] mce_reign+0x168/0x170 26.767565] [<c1024bb5>] mce_end+0x105/0x110 26.767572] [<c10252db>] do_machine_check+0x32b/0x4f0 26.767581] [<c1024fb0>] ? mce_log+0x120/0x120 26.767590] [<c15a5e47>] error_code+0x67/0x6c 26.767602] panic occurred, switching back to text console 26.768498] Rebooting in 30 seconds.. For information, I have also tried earlier Arch Linux. I can install it, but when I try to install a window manager (LXDE) again I got similar errors. Fedora also crashes when installing and also Mandriva did not work for me. Therefore I think something deep in the machine might be wrong. But as stated above I can (clean) install 8.04 and also 9.10 can be installed without problems. Also updates for 8.04 can be installed. My machine is dual boot with XP next to it on a different partition. My HW: Memory : 2.0 GiB; Processor 0: Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz; Processor 1: Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz; How can I install Ubuntu 12.04? Last option would be to completely format my machine and install everything from scratch, but even I am not sure if that would solve it in the end. Can anybody help me out?

  Read the article

• Dual Screen will only mirror after 12.04 upgrade

  - by Ne0

  I have been using Ubuntu with a dual screen for years now, after upgrading to 12.04 LTS i cannot get my dual screen working properly Graphics: 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV350 AR [Radeon 9600] 01:00.1 Display controller: Advanced Micro Devices [AMD] nee ATI RV350 AR [Radeon 9600] (Secondary) I noticed i was using open source drivers and attempted to install official binaries using the methods in this thread. Output: liam@liam-desktop:~$ sudo apt-get install fglrx fglrx-amdcccle Reading package lists... Done Building dependency tree Reading state information... Done The following packages will be upgraded: fglrx fglrx-amdcccle 2 upgraded, 0 newly installed, 0 to remove and 12 not upgraded. Need to get 45.1 MB of archives. After this operation, 739 kB of additional disk space will be used. Get:1 http://gb.archive.ubuntu.com/ubuntu/ precise/restricted fglrx i386 2:8.960-0ubuntu1 [39.2 MB] Get:2 http://gb.archive.ubuntu.com/ubuntu/ precise/restricted fglrx-amdcccle i386 2:8.960-0ubuntu1 [5,883 kB] Fetched 45.1 MB in 1min 33s (484 kB/s) (Reading database ... 328081 files and directories currently installed.) Preparing to replace fglrx 2:8.951-0ubuntu1 (using .../fglrx_2%3a8.960-0ubuntu1_i386.deb) ... Removing all DKMS Modules Error! There are no instances of module: fglrx 8.951 located in the DKMS tree. Done. Unpacking replacement fglrx ... Preparing to replace fglrx-amdcccle 2:8.951-0ubuntu1 (using .../fglrx-amdcccle_2%3a8.960-0ubuntu1_i386.deb) ... Unpacking replacement fglrx-amdcccle ... Processing triggers for ureadahead ... ureadahead will be reprofiled on next reboot Setting up fglrx (2:8.960-0ubuntu1) ... update-alternatives: warning: forcing reinstallation of alternative /usr/lib/fglrx/ld.so.conf because link group i386-linux-gnu_gl_conf is broken. update-alternatives: warning: skip creation of /etc/OpenCL/vendors/amdocl64.icd because associated file /usr/lib/fglrx/etc/OpenCL/vendors/amdocl64.icd (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: warning: skip creation of /usr/lib32/libaticalcl.so because associated file /usr/lib32/fglrx/libaticalcl.so (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: warning: skip creation of /usr/lib32/libaticalrt.so because associated file /usr/lib32/fglrx/libaticalrt.so (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: warning: forcing reinstallation of alternative /usr/lib/fglrx/ld.so.conf because link group i386-linux-gnu_gl_conf is broken. update-alternatives: warning: skip creation of /etc/OpenCL/vendors/amdocl64.icd because associated file /usr/lib/fglrx/etc/OpenCL/vendors/amdocl64.icd (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: warning: skip creation of /usr/lib32/libaticalcl.so because associated file /usr/lib32/fglrx/libaticalcl.so (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: warning: skip creation of /usr/lib32/libaticalrt.so because associated file /usr/lib32/fglrx/libaticalrt.so (of link group i386-linux-gnu_gl_conf) doesn't exist. update-initramfs: deferring update (trigger activated) update-initramfs: Generating /boot/initrd.img-3.2.0-25-generic-pae Loading new fglrx-8.960 DKMS files... Building only for 3.2.0-25-generic-pae Building for architecture i686 Building initial module for 3.2.0-25-generic-pae Done. fglrx: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.2.0-25-generic-pae/updates/dkms/ depmod....... DKMS: install completed. update-initramfs: deferring update (trigger activated) Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Setting up fglrx-amdcccle (2:8.960-0ubuntu1) ... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.2.0-25-generic-pae Processing triggers for libc-bin ... ldconfig deferred processing now taking place liam@liam-desktop:~$ sudo aticonfig --initial -f aticonfig: No supported adapters detected When i attempt to get my settings back to what they were before upgrading i get this message requested position/size for CRTC 81 is outside the allowed limit: position=(1440, 0), size=(1440, 900), maximum=(1680, 1680) and GDBus.Error:org.gtk.GDBus.UnmappedGError.Quark._gnome_2drr_2derror_2dquark.Code3: requested position/size for CRTC 81 is outside the allowed limit: position=(1440, 0), size=(1440, 900), maximum=(1680, 1680) Any idea's on what i need to do to fix this issue?

  Read the article

• Ubuntu 12.04 / 12.10 Randomly Freezing - nVidia?

  - by Alix Axel

  My Ubuntu install frequently freezes, sometimes showing a black screen (not very common anymore - in my latest installs), some other times the mouse and keyboard just fail to move and respond (not even Ctrl + Alt + F1 works) and some other times I'm able to move the mouse with a huge delay (2-5 seconds) but I'm not able to do/click anything. I have a pretty strong feeling that this problem is related to my graphic card drivers because: after hard reset, I usually get error reports about X.org / jockey it's common for artifacts to appear during loading / shutdown / whenever, for instance: pattern filled with £ during log off ugly-colored squared pattern during boot windows that are partially moved (i.e.: only the top half) Firefox renderings that leave the bottom ~30% of the page black These artifacts appear right before the system freezes. I've installed Ubuntu 12.04 LTS and after several failed attempts to get my dual monitor setup to work properly I tried installing the new 12.10 version, hoping that this new version would have this problem solved... Unfortunatly, that was not the case, so I reverted to Ubuntu 12.04. I've tried all the drivers in the Additional Drivers application (even the experimental ones), I've also tried the nvidia-current package from the PPA repository ubuntu-x-swat/x-updates as well as the nouveau OSS driver. Nothing (except no driver at all with a 640*480 resolution) at all seems stable. Here is the info of my graphic card: alix@alix-E500:~$ lspci | grep VGA 01:00.0 VGA compatible controller: NVIDIA Corporation G86 [GeForce 8400M G] (rev a1) alix@alix-E500:~$ sudo lshw -C video [sudo] password for alix: *-display description: VGA compatible controller product: G86 [GeForce 8400M G] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:fd000000-fdffffff memory:d0000000-dfffffff memory:fa000000-fbffffff ioport:cc00(size=128) memory:fe0e0000-fe0fffff Right now, I don't even have my 22" monitor connected as I can't even get my laptop display to work properly and without freezes. I've searched, read and tried all that I could (over several fresh reinstalls) to fix the problem, but so far, no solution has proven definitive. I'm sorry I can't precise which symptom maps to each driver but I've been trying to solve this one on my own without logging what I'm doing, perhaps someone here will be able to point me to a certain-fix solution, if not I'll keep updating this question as I go along. Please let me know if any more info is needed to pinpoint the exact problem. Trying out NVIDIA accelerated graphics driver (version 173). The scrolling, minimizing / maximizing windows takes between 2 and 5 seconds to finalize. Context menus also pop up very slowly and the typing seems delayed by ~1 second. No critical issues so far. Firefox rendering of the Save Edits button is consistently messed up (random black lines in the top). Trying out NVIDIA accelerated graphics driver (version current) [Recommended]. All the delays mentioned above and the buggy rendering of the Save Edits button are gone, but I'm noticing that the whole screen flashes black for a couple of microseconds and while I was writing this test for the first time, the bottom 30% of the screen went black and I couldn't do anything (not even Ctrl + Alt + F1 would work). Had to force a hard reset. Also, the system hanged a little for a couple of seconds with the fade out of the "Restart" menu. Trying out NVIDIA accelerated graphics driver (*experimental*beta) (version experimental-304). Same symptoms as before, it crashed once while I was trying to install Chromium and again after a hard reset when I was trying to remove the driver. The bottom of the screen did not went black and I could move my mouse both times. Ctrl + Alt + F1 didn't work. The ugly-colored pattern also showed up during the second boot. Trying out NVIDIA accelerated graphics driver (*experimental*beta) (version experimental-307). The system crashed as soon as I clicked something. Had to do a fresh re-install. Trying out Nouveau: Accelerated Open Source driver for nVidia cards. Artifacts still show up during boot but other than that this one seems stable. As soon as I connected my second monitor, the responsiveness dropped a lot, animations and video are somewhat slow. I'm gonna try this solution http://askubuntu.com/a/98871/9018 later on.

  Read the article

• Automount of external hard disk

  - by moose

  I have an Intenso 6002560 1TB Memory Station - an external hard disk. This hard disk gets connected via Y-USB cable. When I connect both USB-ends to my Notebook, it gets recognized by my Ubuntu 10.04.4 LTS system: moose@pc07:~$ lsusb [...] Bus 002 Device 005: ID 13fd:1840 Initio Corporation [...] and Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065e10 Device Boot Start End Blocks Id System /dev/sda1 * 1 37810 303704064 83 Linux /dev/sda2 37810 38914 8864769 5 Extended /dev/sda5 37810 38914 8864768 82 Linux swap / Solaris Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0d6ea32a Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976759008+ c W95 FAT32 (LBA) But it did not get mounted: moose@pc07:/dev$ mount -l /dev/sda1 on / type ext4 (rw,errors=remount-ro,user_xattr) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/moose/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=moose) However, I could mount it manually with mount -t vfat /dev/sdc1 /mnt/sdc1 as you can see here: moose@pc07:~$ mount -l /dev/sda1 on / type ext4 (rw,errors=remount-ro,user_xattr) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/moose/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=moose) /dev/sdc1 on /mnt/sdc1 type vfat (rw) edit: Another command: moose@pc07:~$ sudo blkid -o list device fs_type label mount point UUID ---------------------------------------------------------------------------------------------------------------------- /dev/sda1 ext4 / 45eb611b-517e-425b-8057-0391726cccd5 /dev/sda5 swap <swap> e9dc42f3-594c-4b62-874a-305eda5eed41 moose@pc07:~$ blkid -o list device fs_type label mount point UUID ---------------------------------------------------------------------------------------------------------------------- /dev/sda1 ext4 / 45eb611b-517e-425b-8057-0391726cccd5 /dev/sda5 swap <swap> e9dc42f3-594c-4b62-874a-305eda5eed41 /dev/sdc1 /mnt/sdc1 edit: another command: moose@pc07:~$ ls -l /dev/disk/by-uuid/ total 0 lrwxrwxrwx 1 root root 10 2012-09-30 09:31 45eb611b-517e-425b-8057-0391726cccd5 -> ../../sda1 lrwxrwxrwx 1 root root 10 2012-09-30 09:31 e9dc42f3-594c-4b62-874a-305eda5eed41 -> ../../sda5 Here is a link to a Launchpad question about this problem. But I would like it to mount automatically. What do I have to do?

  Read the article

• i don't receive mail notification...Nagios Core 4

  - by alessio

  I have a problem with automatically mail notification in Nagios Core 4 installed on ubuntu 12 .04 lts server... i have tried to send mail with nagios user and root user with the command: echo "test" | mail -s "test mail" [email protected] and i received mail correctly... but i don't receive any automatically mail notification... i don't know how can i do to resolve this issue! :( these are my configuration files (commands.cfg, contacts.cfg, nagios.log, mail.log): commands.cfg (the path /usr/bin/mail is the right path): # 'notify-host-by-email' command definition define command{ command_name notify-host-by-email command_line /usr/bin/printf "%b" "***** Nagios *****\n\nNotification Type: $NOTIFICATIONTYPE$\nHost: $HOSTNAME$\nState: $HOSTSTATE$\nAddress: $HOSTADDRESS$\nInfo: $HOSTOUTPUT$\n\nDate/Time: $LONGDATETIME$\n" | /usr/bin/mail -s "** $NOTIFICATIONTYPE$ Host Alert: $HOSTNAME$ is $HOSTSTATE$ **" $CONTACTEMAIL$ } # 'notify-service-by-email' command definition define command{ command_name notify-service-by-email command_line /usr/bin/printf "%b" "***** Nagios *****\n\nNotification Type: $NOTIFICATIONTYPE$\n\nService: $SERVICEDESC$\nHost: $HOSTALIAS$\nAddress: $HOSTADDRESS$\nState: $SERVICESTATE$\n\nDate/Time: $LONGDATETIME$\n\nAdditional Info:\n\n$SERVICEOUTPUT$\n" | /usr/bin/mail -s "** $NOTIFICATIONTYPE$ Service Alert: $HOSTALIAS$/$SERVICEDESC$ is $SERVICESTATE$ **" $CONTACTEMAIL$ } # 'process-host-perfdata' command definition define command{ command_name process-host-perfdata command_line /usr/bin/printf "%b" "$LASTHOSTCHECK$\t$HOSTNAME$\t$HOSTSTATE$\t$HOSTATTEMPT$\t$HOSTSTATETYPE$\t$HOSTEXECUTIONTIME$\t$HOSTOUTPUT$\t$HOSTPERFDATA$\n" >> /usr/local/nagios/var/host-perfdata.out } # 'process-service-perfdata' command definition define command{ command_name process-service-perfdata command_line /usr/bin/printf "%b" "$LASTSERVICECHECK$\t$HOSTNAME$\t$SERVICEDESC$\t$SERVICESTATE$\t$SERVICEATTEMPT$\t$SERVICESTATETYPE$\t$SERVICEEXECUTIONTIME$\t$SERVICELATENCY$\t$SERVICEOUTPUT$\t$SERVICEPERFDATA$\n" >> /usr/local/nagios/var/service-perfdata.out } contacts.cfg: define contact{ contact_name supporto alias Supporto Clienti DEA service_notification_period 24x7 host_notification_period 24x7 service_notification_options w,u,c,r host_notification_options d,r service_notification_commands notify-service-by-email host_notification_commands notify-host-by-email email [email protected] } define contactgroup{ contactgroup_name admins alias Nagios Administrators members supporto } nagios.log: [1401871412] SERVICE ALERT: fileserver;Current Users;OK;SOFT;2;USERS OK - 1 users currently logged in [1401871953] SERVICE ALERT: backups;Nagios Status;WARNING;SOFT;1;NAGIOS WARNING: 36 processes, status log updated 541 seconds ago [1401872133] SERVICE ALERT: backups;Nagios Status;OK;SOFT;2;NAGIOS OK: 36 processes, status log updated 180 seconds ago [1401872321] SERVICE ALERT: posta;Swap Usage;CRITICAL;SOFT;1;CRITICAL - Plugin timed out after 10 seconds [1401872322] SERVICE ALERT: fileserver;Current Users;CRITICAL;SOFT;1;CRITICAL - Plugin timed out after 10 seconds [1401872420] SERVICE ALERT: archivio;Disk Space;CRITICAL;SOFT;1;CRITICAL - Plugin timed out after 10 seconds [1401872492] SERVICE ALERT: fileserver;Current Users;OK;SOFT;2;USERS OK - 1 users currently logged in [1401872492] SERVICE ALERT: posta;Swap Usage;OK;SOFT;2;SWAP OK: 100% free (1984 MB out of 1984 MB) [1401872590] SERVICE ALERT: archivio;Disk Space;OK;SOFT;2;DISK OK [1401872931] Auto-save of retention data completed successfully. [1401873333] SERVICE ALERT: backups;Nagios Status;WARNING;SOFT;1;NAGIOS WARNING: 36 processes, status log updated 402 seconds ago [1401873513] SERVICE ALERT: backups;Nagios Status;OK;SOFT;2;NAGIOS OK: 36 processes, status log updated 180 seconds ago mail.log (i think that the problem is here but i don't know how to resolve it): Jun 4 10:00:01 backups sm-msp-queue[6109]: My unqualified host name (backups) unknown; sleeping for retry Jun 4 10:01:01 backups sm-msp-queue[6109]: unable to qualify my own domain name (backups) -- using short name Jun 4 10:20:01 backups sm-msp-queue[7247]: My unqualified host name (backups) unknown; sleeping for retry Jun 4 10:21:01 backups sm-msp-queue[7247]: unable to qualify my own domain name (backups) -- using short name Jun 4 10:40:01 backups sm-msp-queue[8327]: My unqualified host name (backups) unknown; sleeping for retry Jun 4 10:41:01 backups sm-msp-queue[8327]: unable to qualify my own domain name (backups) -- using short name Jun 4 11:00:01 backups sm-msp-queue[9549]: My unqualified host name (backups) unknown; sleeping for retry Jun 4 11:01:01 backups sm-msp-queue[9549]: unable to qualify my own domain name (backups) -- using short name Jun 4 11:20:01 backups sm-msp-queue[10678]: My unqualified host name (backups) unknown; sleeping for retry Jun 4 11:21:01 backups sm-msp-queue[10678]: unable to qualify my own domain name (backups) -- using short name i'm at the last step and i want to finish this Nagios Core! :) Any help be appreciate!:) host definition (this host have the disk almost full and it is in hard state but non notification) : define host{ use generic-host ; Name of host template to use host_name posta alias Server Posta ESA address 10.10.2.102 parents xen1, xen2 icon_image redhat.png statusmap_image redhat.gd2 } service definition: define service{ use generic-service host_name xen1, maestro, xen2, posta, nas002, serv2, esasrvmi02, esaubuntumi service_description Disk Space check_command ssh_all_disks!10%!5% } Notification is allowed for the contact definition you gave, but is it also allowed at the the service level ? sorry but i don't understand this thing! :(

  Read the article

• installArchives() failed: perl: warning: Setting locale failed.

  - by Alwin Doss

  I get the following error while updating ubuntu 12.04 LTS installArchives() failed: perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Preconfiguring packages ... perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Preconfiguring packages ... perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Preconfiguring packages ... perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Preconfiguring packages ... (Reading database ... (Reading database ... 5%% (Reading database ... 10%% (Reading database ... 15%% (Reading database ... 20%% (Reading database ... 25%% (Reading database ... 30%% (Reading database ... 35%% (Reading database ... 40%% (Reading database ... 45%% (Reading database ... 50%% (Reading database ... 55%% (Reading database ... 60%% (Reading database ... 65%% (Reading database ... 70%% (Reading database ... 75%% (Reading database ... 80%% (Reading database ... 85%% (Reading database ... 90%% (Reading database ... 95%% (Reading database ... 100%% (Reading database ... 430284 files and directories currently installed.) Preparing to replace libxml2-dev 2.7.8.dfsg-5.1ubuntu4.1 (using .../libxml2-dev_2.7.8.dfsg-5.1ubuntu4.2_i386.deb) ... Unpacking replacement libxml2-dev ... Preparing to replace libxml2 2.7.8.dfsg-5.1ubuntu4.1 (using .../libxml2_2.7.8.dfsg-5.1ubuntu4.2_i386.deb) ... Unpacking replacement libxml2 ... Preparing to replace gstreamer0.10-plugins-bad 0.10.22.3-2ubuntu2 (using .../gstreamer0.10-plugins-bad_0.10.22.3-2ubuntu2.1_i386.deb) ... Unpacking replacement gstreamer0.10-plugins-bad ... Preparing to replace libgstreamer-plugins-bad0.10-0 0.10.22.3-2ubuntu2 (using .../libgstreamer-plugins-bad0.10-0_0.10.22.3-2ubuntu2.1_i386.deb) ... Unpacking replacement libgstreamer-plugins-bad0.10-0 ... Preparing to replace ubuntu-keyring 2011.11.21 (using .../ubuntu-keyring_2011.11.21.1_all.deb) ... /var/lib/dpkg/info/samba4.postinst: 14: /var/lib/dpkg/info/samba4.postinst: /usr/share/samba/setoption.pl: Permission denied dpkg: error processing samba4 (--configure): subprocess installed post-installation script returned error exit status 126

  Read the article

• Desktop login fails, terminal works

  - by Tobias

  I have a freshly setup 12.04 LTS pc system (120 GB SSD, 1 TB HDD, 16 GiB RAM); since a few days, I can't login to the graphical desktop anymore: there is very short flashing shell window which disappears very quickly, and I'm confronted with the login screen again. I believe there is something about modprobe and vbox, but I can't read it fast enough ... I can login to a terminal (Ctrl+Alt+F1). It did not help to chown all contents of my home directory to me:my-group, like suggested here. This is what I could find in /var/log, grepping for the date and time (I inserted linebreaks after <my-hostname>; real time values preserved): auth.log: <date> 22:43:01 <my-hostname> lightdm: pam_succeed_if(lightdm:auth): requirement "user ingroup nopasswdlogin" not met by user "tobias" <date> 22:43:08 <my-hostname> lightdm: pam_unix(lightdm:session): session closed for user lightdm <date> 22:43:08 <my-hostname> lightdm: pam_unix(lightdm:session): session opened for user tobias by (uid=0) <date> 22:43:08 <my-hostname> lightdm: pam_ck_connector(lightdm:session): nox11 mode, ignoring PAM_TTY :0 <date> 22:43:08 <my-hostname> lightdm: pam_unix(lightdm:session): session closed for user tobias <date> 22:43:09 <my-hostname> lightdm: pam_unix(lightdm:session): session opened for user lightdm by (uid=0) <date> 22:43:09 <my-hostname> lightdm: pam_ck_connector(lightdm:session): nox11 mode, ignoring PAM_TTY :0 <date> 22:43:10 <my-hostname> lightdm: pam_succeed_if(lightdm:auth): requirement "user ingroup nopasswdlogin" not met by user "tobias" <date> 22:43:10 <my-hostname> dbus[756]: [system] Rejected send message, 2 matched rules; type="method_call", sender="1:43" (uid=104 pid=1639 comm="/usr/lib/indicator-datetime/indicator-datetime-ser") interface="org.freedesktop.DBus.Properties" member="GetAll" error name="(unset)" requested_reply="0" destination=":1.15" (uid=0 pid=1005 comm="/usr/sbin/console-kit-daemon --no-daemon ") kern.log: <date> 22:43:00 <my-hostname> kernel: [ 16.084525] eth0: no IPv6 routers present syslog: <date> 22:43:00 <my-hostname> kernel: [ 16.084525] eth0: no IPv6 routers present <date> 22:43:01 <my-hostname> ntpdate[1492]: adjust time server 91.189.94.4 offset -0.162831 sec <date> 22:43:08 <my-hostname> acpid: client 969[0:0] has disconnected <date> 22:43:08 <my-hostname> acpid: client connected from 1553[0:0] <date> 22:43:08 <my-hostname> acpid: 1 client rule loaded I have Virtualbox and Truecrypt installed, but I can't think of a reason why they might prevent a graphical login. I'm confused: What is this about requirement "user ingroup nopasswdlogin" not met? I do login using a password, and the password works ok when logging in to a terminal! Can I somehow read the error output, e.g. by delaying it, redirecting it to a file, or having the system prompt me for pressing a key? Has possibly any recent update caused my problem? Should I install the pending updates? How, btw, without access to the graphical UI? I have some working knowledge about the Linux shell, but I'm new to Ubuntu. Any help would be appreciated.

  Read the article

• Terminal Colors Not Working

  - by Matt Fordham

  I am accessing an Ubuntu 10.04.2 LTS server via SSH from OSX. Recently the colors stopped working. I think it happened while I was installing/troubleshooting RVM, but I am not positive. In .bashrc I uncommeneted force_color_prompt=yes, and when I run env | grep TERM I get TERM=xterm-color. But still no colors. Any ideas? Thanks! Here is the output of cat .bashrc # ~/.bashrc: executed by bash(1) for non-login shells. # see /usr/share/doc/bash/examples/startup-files (in the package bash-doc) # for examples # If not running interactively, don't do anything [ -z "$PS1" ] && return # don't put duplicate lines in the history. See bash(1) for more options # ... or force ignoredups and ignorespace HISTCONTROL=ignoredups:ignorespace # append to the history file, don't overwrite it shopt -s histappend # for setting history length see HISTSIZE and HISTFILESIZE in bash(1) HISTSIZE=1000 HISTFILESIZE=2000 # check the window size after each command and, if necessary, # update the values of LINES and COLUMNS. shopt -s checkwinsize # make less more friendly for non-text input files, see lesspipe(1) [ -x /usr/bin/lesspipe ] && eval "$(SHELL=/bin/sh lesspipe)" # set variable identifying the chroot you work in (used in the prompt below) if [ -z "$debian_chroot" ] && [ -r /etc/debian_chroot ]; then debian_chroot=$(cat /etc/debian_chroot) fi # set a fancy prompt (non-color, unless we know we "want" color) case "$TERM" in xterm-color) color_prompt=yes;; esac # uncomment for a colored prompt, if the terminal has the capability; turned # off by default to not distract the user: the focus in a terminal window # should be on the output of commands, not on the prompt force_color_prompt=yes if [ -n "$force_color_prompt" ]; then if [ -x /usr/bin/tput ] && tput setaf 1 >&/dev/null; then # We have color support; assume it's compliant with Ecma-48 # (ISO/IEC-6429). (Lack of such support is extremely rare, and such # a case would tend to support setf rather than setaf.) color_prompt=yes else color_prompt= fi fi if [ "$color_prompt" = yes ]; then PS1='${debian_chroot:+($debian_chroot)}\[\033[01;32m\]\u@\h\[\033[00m\]:\[\033[01;34m\]\w\[\033[00m\]\$ ' else PS1='${debian_chroot:+($debian_chroot)}\u@\h:\w\$ ' fi unset color_prompt force_color_prompt # If this is an xterm set the title to user@host:dir case "$TERM" in xterm*|rxvt*) PS1="\[\e]0;${debian_chroot:+($debian_chroot)}\u@\h: \w\a\]$PS1" ;; *) ;; esac # enable color support of ls and also add handy aliases if [ -x /usr/bin/dircolors ]; then test -r ~/.dircolors && eval "$(dircolors -b ~/.dircolors)" || eval "$(dircolors -b)" alias ls='ls --color=auto' alias dir='dir --color=auto' alias vdir='vdir --color=auto' alias grep='grep --color=auto' alias fgrep='fgrep --color=auto' alias egrep='egrep --color=auto' fi # some more ls aliases alias ll='ls -alF' alias la='ls -A' alias l='ls -CF' # Alias definitions. # You may want to put all your additions into a separate file like # ~/.bash_aliases, instead of adding them here directly. # See /usr/share/doc/bash-doc/examples in the bash-doc package. if [ -f ~/.bash_aliases ]; then . ~/.bash_aliases fi # enable programmable completion features (you don't need to enable # this, if it's already enabled in /etc/bash.bashrc and /etc/profile # sources /etc/bash.bashrc). if [ -f /etc/bash_completion ] && ! shopt -oq posix; then . /etc/bash_completion fi [[ -s "/usr/local/rvm/scripts/rvm" ]] && . "/usr/local/rvm/scripts/rvm"

  Read the article

• It's like I'm in recovery mode after update, but I'm not

  - by mawburn

  I used the Ubuntu software updater and updated to the most recent packages. After the last update today, it's like I have gone into recovery mode, but I haven't. I am running UbuntuGNOME First, everything looks like this: Switching to dark mode does nothing. Also, default applications do not work. Such as Startup and the default screenshot application. Everything was working fine before the latest software update. System Info Ubuntu 14.04 LTS Gnome-Shell 3.10.4 Kernel 3.13.0-29 I can't figure out how to get an update history, but this is almost a fresh install. It's about a week old install and this is the 3rd time I've used the Ubuntu Software Update. I am running AMD ATI HD6700 with the proprietary Catalyst drivers. I tried to provide all information that I thought would be useful, if you need any more please let me know. Edit - I believe something went wrong within these updates: Update Log: Start-Date: 2014-06-09 19:07:07 Commandline: aptdaemon role='role-commit-packages' sender=':1.68' Install: libgnome-desktop-3-10:amd64 (3.12.0-0~eugenesan~trusty2) Upgrade: gnome-session-common:amd64 (3.9.90-0ubuntu12, 3.12.0-0~eugenesan~trusty10), gnome-session-bin:amd64 (3.9.90-0ubuntu12, 3.12.0-0~eugenesan~trusty10), gir1.2-gnomedesktop-3.0:amd64 (3.8.4-0ubuntu3, 3.12.0-0~eugenesan~trusty2), gnome-session:amd64 (3.9.90-0ubuntu12, 3.12.0-0~eugenesan~trusty10), python-libxml2:amd64 (2.9.1+dfsg1-3ubuntu4.1, 2.9.1+dfsg1-3ubuntu4.2), libspice-server1:amd64 (0.12.4-0nocelt2, 0.12.4-0nocelt2.02~eugenesan~trusty1), gir1.2-mutter-3.0:amd64 (3.10.4-0ubuntu2, 3.10.4-0ubuntu2.1), xserver-xorg-video-qxl:amd64 (0.1.1-0ubuntu3, 0.1.1-0ubuntu3.01), libxml2:amd64 (2.9.1+dfsg1-3ubuntu4.1, 2.9.1+dfsg1-3ubuntu4.2), libxml2:i386 (2.9.1+dfsg1-3ubuntu4.1, 2.9.1+dfsg1-3ubuntu4.2), gnome-desktop3-data:amd64 (3.8.4-0ubuntu3, 3.12.0-0~eugenesan~trusty2), mutter:amd64 (3.10.4-0ubuntu2, 3.10.4-0ubuntu2.1), mutter-common:amd64 (3.10.4-0ubuntu2, 3.10.4-0ubuntu2.1), libxml2-utils:amd64 (2.9.1+dfsg1-3ubuntu4.1, 2.9.1+dfsg1-3ubuntu4.2), libmutter0c:amd64 (3.10.4-0ubuntu2, 3.10.4-0ubuntu2.1) End-Date: 2014-06-09 19:07:12 I also installed Citrix Receiver today, following the tutorial here: Citrix Receiver 12.1 on Ubuntu 14.04 64-bit Log Start-Date: 2014-06-09 18:59:06 Commandline: apt-get install libmotif4:i386 nspluginwrapper lib32z1 libc6-i386 libxp6:i386 libxpm4:i386 libasound2:i386 Install: libmotif-common:amd64 (2.3.4-5, automatic), libatk1.0-0:i386 (2.10.0-2ubuntu2, automatic), libxft2:i386 (2.3.1-2, automatic), libgraphite2-3:i386 (1.2.4-1ubuntu1, automatic), nspluginviewer:i386 (1.4.4-0ubuntu5, automatic), libpango-1.0-0:i386 (1.36.3-1ubuntu1, automatic), libxcursor1:i386 (1.1.14-1, automatic), libmotif4:i386 (2.3.4-5), libxm4:amd64 (2.3.4-5, automatic), libxm4:i386 (2.3.4-5, automatic), libxp6:i386 (1.0.2-1ubuntu1), libpangocairo-1.0-0:i386 (1.36.3-1ubuntu1, automatic), libxcb-render0:i386 (1.10-2ubuntu1, automatic), libthai0:i386 (0.1.20-3, automatic), libharfbuzz0b:i386 (0.9.27-1, automatic), libpixman-1-0:i386 (0.30.2-2ubuntu1, automatic), libpangoft2-1.0-0:i386 (1.36.3-1ubuntu1, automatic), libcairo2:i386 (1.13.0~20140204-0ubuntu1, automatic), lib32z1:amd64 (1.2.8.dfsg-1ubuntu1), libjasper1:i386 (1.900.1-14ubuntu3, automatic), libgtk2.0-0:i386 (2.24.23-0ubuntu1.1, automatic), nspluginwrapper:amd64 (1.4.4-0ubuntu5), libuil4:amd64 (2.3.4-5, automatic), libuil4:i386 (2.3.4-5, automatic), libxcb-shm0:i386 (1.10-2ubuntu1, automatic), libxmu6:i386 (1.1.1-1, automatic), libc6-i386:amd64 (2.19-0ubuntu6), libxinerama1:i386 (1.1.3-1, automatic), libgdk-pixbuf2.0-0:i386 (2.30.7-0ubuntu1, automatic), libxcomposite1:i386 (0.4.4-1, automatic), libmrm4:amd64 (2.3.4-5, automatic), libmrm4:i386 (2.3.4-5, automatic), libdatrie1:i386 (0.2.8-1, automatic), libxrandr2:i386 (1.4.2-1, automatic), libxpm4:i386 (3.5.10-1) End-Date: 2014-06-09 18:59:11

  Read the article

• Swap not available on System Monitor

  - by Zaki

  I had a swap partition of 1GB (RAM 1GB, Ubuntu 12.04 lts). Now swap is not shown on System Monitor neither can I hibernate my pc (sudo pm-hibernate). blkid output: /dev/sda1: UUID="B8B4FBB1B4FB706C" TYPE="ntfs" /dev/sda2: UUID="2ea7d608-2d89-4e41-9436-d05cb3ce8871" TYPE="swap" /dev/sda3: UUID="3219d03a-67e4-454b-8ce7-a27831846e35" TYPE="ext4" /dev/sda5: LABEL="Softwares" UUID="AC1CC3301CC2F47C" TYPE="ntfs" /dev/sda6: LABEL="Education" UUID="1E103E6C103E4B53" TYPE="ntfs" /dev/sda7: LABEL="Recreation" UUID="2CC8D181C8D149AA" TYPE="ntfs" /dev/sda8: LABEL="Miscellaneous" UUID="0274D6B174D6A727" TYPE="ntfs" /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda6 during installation UUID=3219d03a-67e4-454b-8ce7-a27831846e35 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=2ea7d608-2d89-4e41-9436-d05cb3ce8871 none swap sw 0 0 free -m total used free shared buffers cached Mem: 991 867 123 0 27 418 -/+ buffers/cache: 421 569 Swap: 0 0 0 cat /proc/swaps Filename Type Size Used Priority fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9f369f36 Device Boot Start End Blocks Id System /dev/sda1 * 63 31471334 15735636 7 HPFS/NTFS/exFAT /dev/sda2 31471616 33470447 999416 82 Linux swap / Solaris /dev/sda3 33472512 62539775 14533632 83 Linux /dev/sda4 62541045 312592769 125025862+ f W95 Ext'd (LBA) /dev/sda5 62541108 125066024 31262458+ 7 HPFS/NTFS/exFAT /dev/sda6 125066088 187591004 31262458+ 7 HPFS/NTFS/exFAT /dev/sda7 187591068 250115984 31262458+ 7 HPFS/NTFS/exFAT /dev/sda8 250116048 312576704 31230328+ 7 HPFS/NTFS/exFAT swapon --all swapon: /dev/sda2: swapon failed: Invalid argument dmesg | grep -A 5 -B 5 -i swap [ 9.487404] EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 131645 [ 9.487413] EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 131330 [ 9.487418] EXT4-fs (sda3): 16 orphan inodes deleted [ 9.487420] EXT4-fs (sda3): recovery complete [ 9.578600] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null) [ 20.580539] Swap area shorter than signature indicates [ 20.588363] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 20.619443] udevd[330]: starting version 175 [ 20.649959] lp: driver loaded but no devices found [ 20.662972] [drm] Initialized drm 1.1.0 20060810 [ 20.675515] i915 0000:00:02.0: setting latency timer to 64 -- [ 72.288573] PM: thaw of drv:sr dev:3:0:0:0 complete after 178.143 msecs [ 72.288578] PM: thaw of drv:scsi_device dev:3:0:0:0 complete after 178.136 msecs [ 72.299677] PM: thaw of drv:scsi_device dev:2:0:0:0 complete after 189.270 msecs [ 72.309473] PM: thaw of devices complete after 202.763 msecs [ 72.309668] PM: writing image. [ 72.309670] PM: Cannot find swap device, try swapon -a. [ 72.309699] PM: Cannot get swap writer [ 72.329896] Restarting tasks ... done. [ 72.331777] PM: Basic memory bitmaps freed [ 72.331792] video LNXVIDEO:00: Restoring backlight state [ 72.420048] option1 ttyUSB0: option_instat_callback: error -84 [ 72.804047] option1 ttyUSB0: option_instat_callback: error -84 -- [ 145.960625] sd 7:0:0:0: Attached scsi generic sg2 type 0 [ 145.972036] sd 7:0:0:0: [sdb] Attached SCSI removable disk [ 172.430508] PPP BSD Compression module registered [ 172.455583] PPP Deflate Compression module registered [ 332.260789] type=1400 audit(1381814763.342:27): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=636 comm="cupsd" pid=636 comm="cupsd" capability=36 capname="block_suspend" [ 1913.030998] Swap area shorter than signature indicates [ 2022.530155] type=1400 audit(1381816453.610:28): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=636 comm="cupsd" pid=636 comm="cupsd" capability=36 capname="block_suspend" [ 4062.729509] Swap area shorter than signature indicates Please help. Thanks in advance. df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 14G 6.1G 7.0G 47% / udev 488M 4.0K 488M 1% /dev tmpfs 199M 868K 198M 1% /run none 5.0M 4.0K 5.0M 1% /run/lock none 496M 224K 496M 1% /run/shm

  Read the article

• Need help with chronic slow wifi connections

  - by mgeorge

  I have had chronic slow wifi connections on several networks for a while now, I think since my update to 12.04 when it came out. I have tried many of the tips and tricks already available out there in the forums with no luck (wicd, etc..). I want to see if any of you experts out there might be able to help me, and thanks in advance!! I use ubuntu 12.04 on a lenovo ideapad y650, and most networks I connect to lose the connection frequently or do not give appropriate bandwidth when I am connected. Here are some results of the usual go-to system checks: cat /etc/lsb-release; uname -a: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Linux mgeorge-lenovo 3.2.0-48-generic-pae #74-Ubuntu SMP Thu Jun 6 20:05:01 UTC 2013 i686 i686 i386 GNU/Linux lspci -nnk | grep -iA2 net: 04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlwifi -- 08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) Subsystem: Lenovo Device [17aa:3878] Kernel driver in use: tg3 lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 090c:7371 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) iwconfig: lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Dyno" Mode:Managed Frequency:2.412 GHz Access Point: CC:5D:4E:46:0A:93 Bit Rate=150 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-40 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:948 Invalid misc:728 Missed beacon:0 eth0 no wireless extensions. rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod: Module Size Used by uvcvideo 67203 0 videodev 86588 1 uvcvideo nouveau 712674 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197641 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau mxm_wmi 12893 1 nouveau wmi 18744 1 mxm_wmi joydev 17393 0 arc4 12473 2 snd_hda_codec_realtek 174313 1 snd_hda_codec_hdmi 31775 1 snd_hda_intel 32719 3 snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80916 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi psmouse 86520 0 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event serio_raw 13027 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq iwlwifi 366509 0 mac80211 436493 1 iwlwifi snd 62218 16 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,sn d_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 17890 0 sparse_keymap 13658 1 ideapad_laptop cfg80211 178877 2 iwlwifi,mac80211 ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 ir_rc5_decoder 12459 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 video 19115 1 nouveau ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir bnep 17830 2 rfcomm 38139 0 parport_pc 32114 0 bluetooth 158479 10 bnep,rfcomm ppdev 12849 0 binfmt_misc 17292 1 mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141414 0 nm-tool: NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: tg3 State: unavailable Default: no HW Address: 00:23:5A:CC:85:BD Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 [Dyno] -------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: yes HW Address: 00:22:FA:D0:94:CA Capabilities: Speed: 150 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) *Dyno: Infra, CC:5D:4E:46:0A:93, Freq 2412 MHz, Rate 54 Mb/s, Strength 81 WPA2 IPv4 Settings: Address: 10.0.0.43 Prefix: 24 (255.255.255.0) Gateway: 10.0.0.1 DNS: 10.0.0.1

  Read the article

• Ubuntu 12.04 LXC nat prerouting not working

  - by petermolnar

  I have a running Debian Wheezy setup I copied exactly to an Ubuntu 12.04 ( elementary OS, used as desktop as well ) While the Debian setup runs flawlessly, the Ubuntu version dies on the prerouting to containers ( or so it seems ) In short: lxc works containers work and run connecting to container from host OK ( including mixed ports & services ) connecting to outside world from container is fine What does not work is connecting from another box to the host on a port that should be NATed to a container. The setups: /etc/rc.local CMD_BRCTL=/sbin/brctl CMD_IFCONFIG=/sbin/ifconfig CMD_IPTABLES=/sbin/iptables CMD_ROUTE=/sbin/route NETWORK_BRIDGE_DEVICE_NAT=lxc-bridge HOST_NETDEVICE=eth0 PRIVATE_GW_NAT=192.168.42.1 PRIVATE_NETMASK=255.255.255.0 PUBLIC_IP=192.168.13.100 ${CMD_BRCTL} addbr ${NETWORK_BRIDGE_DEVICE_NAT} ${CMD_BRCTL} setfd ${NETWORK_BRIDGE_DEVICE_NAT} 0 ${CMD_IFCONFIG} ${NETWORK_BRIDGE_DEVICE_NAT} ${PRIVATE_GW_NAT} netmask ${PRIVATE_NETMASK} promisc up Therefore lxc network is 192.168.42.0/24 and the host eth0 ip is 192.168.13.100; setup via network manager as static address. iptables: *mangle :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT *filter :FORWARD ACCEPT [0:0] :INPUT DROP [0:0] :OUTPUT ACCEPT [0:0] # Accept traffic from internal interfaces -A INPUT -i lo -j ACCEPT # accept traffic from lxc network -A INPUT -d 192.168.42.1 -s 192.168.42.0/24 -j ACCEPT # Accept internal traffic Make sure NEW incoming tcp connections are SYN # packets; otherwise we need to drop them: -A INPUT -p tcp ! --syn -m state --state NEW -j DROP # Packets with incoming fragments drop them. This attack result into Linux server panic such data loss. -A INPUT -f -j DROP # Incoming malformed XMAS packets drop them: -A INPUT -p tcp --tcp-flags ALL ALL -j DROP # Incoming malformed NULL packets: -A INPUT -p tcp --tcp-flags ALL NONE -j DROP # Accept traffic with the ACK flag set -A INPUT -p tcp -m tcp --tcp-flags ACK ACK -j ACCEPT # Allow incoming data that is part of a connection we established -A INPUT -m state --state ESTABLISHED -j ACCEPT # Allow data that is related to existing connections -A INPUT -m state --state RELATED -j ACCEPT # Accept responses to DNS queries -A INPUT -p udp -m udp --dport 1024:65535 --sport 53 -j ACCEPT # Accept responses to our pings -A INPUT -p icmp -m icmp --icmp-type echo-reply -j ACCEPT # Accept notifications of unreachable hosts -A INPUT -p icmp -m icmp --icmp-type destination-unreachable -j ACCEPT # Accept notifications to reduce sending speed -A INPUT -p icmp -m icmp --icmp-type source-quench -j ACCEPT # Accept notifications of lost packets -A INPUT -p icmp -m icmp --icmp-type time-exceeded -j ACCEPT # Accept notifications of protocol problems -A INPUT -p icmp -m icmp --icmp-type parameter-problem -j ACCEPT # Respond to pings, but limit -A INPUT -m icmp -p icmp --icmp-type echo-request -m state --state NEW -m limit --limit 6/s -j ACCEPT # Allow connections to SSH server -A INPUT -p tcp -m tcp --dport 22 -m state --state NEW -m limit --limit 12/s -j ACCEPT COMMIT *nat :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A PREROUTING -d 192.168.13.100 -p tcp -m tcp --dport 2221 -m state --state NEW -m limit --limit 12/s -j DNAT --to-destination 192.168.42.11:22 -A PREROUTING -d 192.168.13.100 -p tcp -m tcp --dport 80 -m state --state NEW -m limit --limit 512/s -j DNAT --to-destination 192.168.42.11:80 -A PREROUTING -d 192.168.13.100 -p tcp -m tcp --dport 443 -m state --state NEW -m limit --limit 512/s -j DNAT --to-destination 192.168.42.11:443 -A POSTROUTING -d 192.168.42.0/24 -o eth0 -j SNAT --to-source 192.168.13.100 -A POSTROUTING -o eth0 -j MASQUERADE COMMIT sysctl: net.ipv4.conf.all.forwarding = 1 net.ipv4.conf.all.mc_forwarding = 0 net.ipv4.conf.default.forwarding = 1 net.ipv4.conf.default.mc_forwarding = 0 net.ipv4.ip_forward = 1 I've set up full iptables log on the container; none of the packets addressed to 192.168.13.100, port 80 is reaching the container. I've even tried different kernels ( server kernel, raring lts kernel, etc ), modprobe everything iptables & nat related, nothing. Any ideas?

  Read the article

• broken upgrade from 10.04 to 12.04 on a VPS - recoverable?

  - by HorusKol

  I have a VPS hosted 1500 km away. It originally came with 9.10 - and this morning I decided that I really should get to an LTS release, and figured I'd jump to 12.04. Researching, I discovered that there is no direct path between 9.10 and 12.04, but that I could upgrade via 10.04. After backing up my data, I dove in. The upgrade to 10.04 was successful, and I proceeded to upgrade to 12.04. Things started to go wrong. First, I got an error with GLIBC - I retried and got the same error. That's when I stopped the upgrade. I then tried another round of apt-get update && apt-get upgrade and got a list of "unmet dependencies": apt: Depends: ubuntu-keyring but it is not going to be installed Depends: libc6 (>= 2.15) but 2.11.1-0ubuntu7.11 is to be installed Depends: libstdc++6 (>= 4.6) but 4.4.3-4ubuntu5.1 is to be installed PreDepends: dpkg (>= 1.15.7.2) but 1.15.5.6ubuntu4.6 is to be installed apt-utils: Depends: libapt-pkg-libc6.10-6-4.8 libapt-inst1.4: Depends: libc6 (>= 2.14) but 2.11.1-0ubuntu7.11 is to be installed libapt-pkg4.12: Depends: libc6 (>= 2.15) but 2.11.1-0ubuntu7.11 is to be installed Depends: libstdc++6 (>= 4.6) but 4.4.3-4ubuntu5.1 is to be installed libc6: Depends: libc-bin (= 2.11.1-0ubuntu7.11) but 2.15-0ubuntu10.2 is to be installed libept0: Depends: libapt-pkg-libc6.10-6-4.8 libnih-dbus1: Depends: libnih1 (= 1.0.3-4ubuntu9) but 1.0.1-1 is to be installed I tried to see if I could do something about these - using apt-get -f install. This told me that I would need to upgrade my kernel. I found instructions on how to do this, but when I ran apt-get to install the new linux headers, I got the same dependency errors. I found another answer here where someone else had had an interruption in their upgrade - and tried the solution that worked for them: sudo apt-get -f dist-upgrade This resulted in the error: E: Could not perform immediate configuration on 'python2.7-minimal'.Please see man 5 apt.conf under APT::Immediate-Configure for details. (2) I tried to resolve this by: apt-get install -o APT::Immediate-Configure=false -f apt python-minimal But this simply ended up with this last list of dependency errors: apt: Depends: ubuntu-keyring but it is not going to be installed Depends: libc6 (>= 2.15) but 2.11.1-0ubuntu7.11 is to be installed Depends: libstdc++6 (>= 4.6) but 4.4.3-4ubuntu5.1 is to be installed PreDepends: dpkg (>= 1.15.7.2) but 1.15.5.6ubuntu4.6 is to be installed apt-utils: Depends: libapt-pkg-libc6.10-6-4.8 libapt-inst1.4: Depends: libc6 (>= 2.14) but 2.11.1-0ubuntu7.11 is to be installed libapt-pkg4.12: Depends: libc6 (>= 2.15) but 2.11.1-0ubuntu7.11 is to be installed Depends: libstdc++6 (>= 4.6) but 4.4.3-4ubuntu5.1 is to be installed libc6: Depends: libc-bin (= 2.11.1-0ubuntu7.11) but 2.15-0ubuntu10.2 is to be installed libept0: Depends: libapt-pkg-libc6.10-6-4.8 libnih-dbus1: Depends: libnih1 (= 1.0.3-4ubuntu9) but 1.0.1-1 is to be installed python: Depends: python-minimal (= 2.6.5-0ubuntu1) but 2.7.3-0ubuntu2 is to be installed python-apt: Depends: libapt-pkg-libc6.10-6-4.8 python-minimal: Depends: python2.7-minimal (>= 2.7.3) but it is not going to be installed Breaks: python-support (< 1.0.10ubuntu2) but 1.0.4ubuntu1 is to be installed synaptic: Depends: libapt-pkg-libc6.10-6-4.8 Any ideas on how to dig out of this hole?

  Read the article

• Randomely loosing wireless connexion with Cubuntu 12.04

  - by statquant

  I am presently experiencing random disconnections from my wireless network. It looks like it is more and more frequent (however I have not seen any clear pattern). This is killing me... Here is some information that should help (from ubuntu forums). Thanks for reading Machine : Acer Aspire S3 statquant@euclide:~$ lsb_release -d Description: Ubuntu 12.04.1 LTS statquant@euclide:~$ uname -mr 3.2.0-33-generic x86_64 statquant@euclide:~$ sudo /etc/init.d/networking restart * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... statquant@euclide:~$ lspci 02:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) statquant@euclide:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 004: ID 064e:c321 Suyin Corp. Bus 002 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. statquant@euclide:~$ ifconfig wlan0 Link encap:Ethernet HWaddr 74:de:2b:dd:c4:78 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::76de:2bff:fedd:c478/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:913 errors:0 dropped:0 overruns:0 frame:0 TX packets:802 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:873218 (873.2 KB) TX bytes:125826 (125.8 KB) statquant@euclide:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"Bbox-D646D1" Mode:Managed Frequency:2.437 GHz Access Point: 00:19:70:80:01:6C Bit Rate=65 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=56/70 Signal level=-54 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:71 Missed beacon:0 statquant@euclide:~$ dmesg | grep "wlan" [ 17.495866] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 17.498950] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 20.072015] wlan0: authenticate with 00:19:70:80:01:6c (try 1) [ 20.269853] wlan0: authenticate with 00:19:70:80:01:6c (try 2) [ 20.272386] wlan0: authenticated [ 20.298682] wlan0: associate with 00:19:70:80:01:6c (try 1) [ 20.302321] wlan0: RX AssocResp from 00:19:70:80:01:6c (capab=0x431 status=0 aid=1) [ 20.302325] wlan0: associated [ 20.307307] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 30.402292] wlan0: no IPv6 routers present statquant@euclide:~$ sudo lshw -C network [sudo] password for statquant: *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 74:de:2b:dd:c4:78 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-33-generic firmware=N/A ip=192.168.1.3 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c0400000-c047ffff memory:afb00000-afb0ffff statquant@euclide:~$ iwlist scan wlan0 Scan completed : Cell 01 - Address: 00:19:70:80:01:6C Channel:6 Frequency:2.437 GHz (Channel 6) Quality=56/70 Signal level=-54 dBm Encryption key:on ESSID:"Bbox-D646D1" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000125fb152bb Extra: Last beacon: 40020ms ago IE: Unknown: 000B42626F782D443634364431 IE: Unknown: 010882848B960C121824 IE: Unknown: 030106 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101820003A4000027A4000042435E0062322F00 IE: Unknown: 2D1A4C101BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D1606080800000000000000000000000000000000000000 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000 And... finally, please note that I did the following (after looking for fixes of similar problems), but unfortunately it did not work sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1

  Read the article

• Error while updating

  - by Alwin Doss

  I get the following error while updating ubuntu 12.04 LTS installArchives() failed: perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Preconfiguring packages ... perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Preconfiguring packages ... perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Preconfiguring packages ... perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Preconfiguring packages ... (Reading database ... (Reading database ... 5%% (Reading database ... 10%% (Reading database ... 15%% (Reading database ... 20%% (Reading database ... 25%% (Reading database ... 30%% (Reading database ... 35%% (Reading database ... 40%% (Reading database ... 45%% (Reading database ... 50%% (Reading database ... 55%% (Reading database ... 60%% (Reading database ... 65%% (Reading database ... 70%% (Reading database ... 75%% (Reading database ... 80%% (Reading database ... 85%% (Reading database ... 90%% (Reading database ... 95%% (Reading database ... 100%% (Reading database ... 430284 files and directories currently installed.) Preparing to replace libxml2-dev 2.7.8.dfsg-5.1ubuntu4.1 (using .../libxml2-dev_2.7.8.dfsg-5.1ubuntu4.2_i386.deb) ... Unpacking replacement libxml2-dev ... Preparing to replace libxml2 2.7.8.dfsg-5.1ubuntu4.1 (using .../libxml2_2.7.8.dfsg-5.1ubuntu4.2_i386.deb) ... Unpacking replacement libxml2 ... Preparing to replace gstreamer0.10-plugins-bad 0.10.22.3-2ubuntu2 (using .../gstreamer0.10-plugins-bad_0.10.22.3-2ubuntu2.1_i386.deb) ... Unpacking replacement gstreamer0.10-plugins-bad ... Preparing to replace libgstreamer-plugins-bad0.10-0 0.10.22.3-2ubuntu2 (using .../libgstreamer-plugins-bad0.10-0_0.10.22.3-2ubuntu2.1_i386.deb) ... Unpacking replacement libgstreamer-plugins-bad0.10-0 ... Preparing to replace ubuntu-keyring 2011.11.21 (using .../ubuntu-keyring_2011.11.21.1_all.deb) ... /var/lib/dpkg/info/samba4.postinst: 14: /var/lib/dpkg/info/samba4.postinst: /usr/share/samba/setoption.pl: Permission denied dpkg: error processing samba4 (--configure): subprocess installed post-installation script returned error exit status 126

  Read the article

• How to fix: Ubuntu 12.04 reboots after loading with elilo

  - by Casey

  I have an HP p6-2120 with CPU: AMD A6-3620 APU with Radeon Graphics RAM: 6GB BIOS: HO2_710.ROM v7.10 [AMI v7.10 4/19/2012] Disk: SATA1 (/dev/sda) - 1 TB (windows) Disk: SATA2 (/dev/sdb) - 1 TB partitioned using "parted -a optimal /dev/sdb" as follows: .. 1049KB 201MB FAT32 boot flag set .. 201MB 60GB ext2 (/) .. 68GB 78GB linux-swap(v1) (swap) .. 78GB 790GB ext4 (/home) .. - rest is "free" space reserved for other purposes (eventually) ubuntu: 12.04.1 LTS [specifically: Release 12.04 (precise) 64-bit] kernel: linux 3.2.0-29-generic I created a bootable EFI USB from the ISO (64-bit) which I downloaded. I can run and install from the USB without any problems. The BIOS is an EFI bios that appears to be capable of booting in either EFI or Legacy mode. Initially, I did the "standard" install with NOTHING on disk2, and let the installer configure everything. The net result of this was that when I started the computer and forced it into "boot" menu mode, it DOES NOT recognize SATA2 as an EFI drive, and when I attempt to "legacy" boot from it, I get the message "ERROR: No Boot Disk has been detected." The "standard" install created one large partition that consumed the entire disk. At that point, I manually partitioned the disk (using sudo parted -a optimal /dev/sdb) as described above. I selected the "other" install, and changed the /dev/sdb1 to "bios_grub", /dev/sdb2 as "/" (ext4), /dev/sdb3 as swap, and /dev/sdb4 as "/home". [Note: fearing that possibly elilo did not recognize ext4, I switched /dev/sdb2 to ext2 and re-insalled] The net result was that the install appeared to trash the /dev/sdb1 partition so that it was NOT readable by anything. I re-formated /dev/sdb1 as FAT32 and set the boot flag. I repeated the install ignoring the messages about no bios_grub partition. After several attempts to get GRUB2 to work, I switched to elilo. I downloaded the most recent version and copied it (elilo-3.14-ia64.efi) to /dev/sdb1/efi/boot/bootx64.efi. (The BIOS boot loader did not recognize it either as elilo-3.14.ia64.efi or as elilo.efi. Based on the advice in one of the web-pages I found, I renamed it to bootx64.efi. This worked.) In that same directory (/efi/boot), I copied the file pointed to the link in /dev/sdb2/vmlinuz to /efi/boot/vmlinuz, and the file pointed to the link in /dev/sdb2/initrd.img to /efi/boot/initrd.img. I created an elilo.conf file as follows: timeout=5000 prompt default=linux-boot image=vmlinuz label=linux-boot read-only initrd=initrd.img root=/dev/sdb2 The /efi/boot directory contains 4 files: bootx64.efi elilo.conf vmlinuz initrd.img When I power-cycle the computer and force the boot menu, drive2 shows up as an EFI bootable drive. When I select it, I get the elilo prompt. Pressing , it appears to load the kernal (I have tried it with verbose=5, and there is a long string of messages with the final one a command line to load the kernel and a series of several dots that fly by) then the screen goes blank, and it reboots the computer. [Note: I have also tried substituting the UUID as found in the /etc/fstab of the installed system for the root directory. This had no effect.] This is a brief synopsis of several nights of fiddling with this. I would deeply appreciate any help you can give.

  Read the article

• Video works with 'Try me' but not after install. What is the difference? U12.04LTS,

  - by HarveyP

  My hard drive got corrupted so I did a reinstall. Tested Youtube in FF during 'try me' and it worked - jerky, but it worked. Instal without all the updates (576 outstanding now) in order to get ff installed as per the demo - to no avail. In 'try me' mode ff NEVER crashed! After install ff crashed whilst I was typing in 'youtube' in the address field. When I finally got to youtube - no video. What is the difference between ff in try me and ff after install? Off to try some selected updates now to see if I can see it for myself. In previous installation I had several profiles and aliased ff with -safe-mode switch to simplify startup of most stable ff. Also found that ff startup in graphic mode worked better (but still without video) with all of the extensions disabled and all of the plugins set to "ask" and always denied ... I have SiS graphic card in SiS Motherboard for XP and ancient Hyundai ImageQuest QV770 monitor. I have Ubuntu 12.04.01 LTS 1 day after install with only the immediate upgrades requested to language pack (English UK). Using FR Alternative keyboard. Connected with domestic wifi network from Orange (FT) I really want to use Skype, but won't bother installing it (again) without video as I can do my sms on FB - whilst ff is not crashed ... Update ... Is something overflowing? I have just had to reboot in order to get ff to restart in any way shape or form - restart on crash form generates new crash form, etc. It was however a good half hour before it crashed so some improvement over conditions before disk corruption. I have now installed all of the critical updates (332 recommended updates still outstanding) which included some relating to ff. Still no video. Still crashing - especially when on Grepolis website. Since the re-install I have had a lovely 1024x768 screen, but after last ff crash and reboot I got a message about 'low graphics mode' and 'setting things myself'. I was not sufficiently tuned in at the time to take proper note - I have no doubt I shall see it again and shall report accordingly. I still have only laptop options for my screen and do not know how to rectify this. Spent a few days with ubuntu on a different, newer machine which has now suffered a graphics breakdown. Returned to this old one again, but with new flat screen Monitor. Found SIS drivers for my graphics BUT it is intended for Red Hat 7.2. I chose this over the version for 7.0 because I thought what the hell, I might not be able to do anything with either of them but this is the later one ... The file will not open with software manager - found a similar problem on Overclock but it has not helped me to install this driver. File name is sis_drv.o-410 and it is currently idling away in my Downloads folder ... I have tried the solution offered on another sis problem, but this shows that my xserver-xorg-video-sis driver is up to date. I am now at a loss as to how to proceed if I can't install the latest sis driver from sis ... Does nobody know how FF changes from "try-me" to "installed"? Any time I MUST have video I reboot from the disk again, but this is tedious! Also one of the things I mock most about MS is the constant rebooting ... UPDATE 10/6/2014 I have installed chromium-browser - worse, crashes even more often than ff.I have installed epiphany - better; Video works but not the associated soundtrack.FireFox is version 14.01 in 'try me' and version 29.0 from my install. Would it be useful to try to downgrade FireFox in order to get video?

  Read the article

• "The connection has timed out" - Please help!

  - by gon

  I recently installed a fresh Ubuntu 12.04 LTS on a desktop, and the installation itself was successful (other than 'grub rescue' issue that I encountered but fixed) but this connection problem is really giving me a headache. Symptoms: 1. When I open the FireFox browser and try to connect to a website, it just hangs for a while saying "Connecting..." but eventually loads an error page "The connection has timed out". 2. It's not a browser problem (and I tried setting ipv6 thing to "true" at about:config) because running "sudo apt-get install [some-random-package]" at terminal fails ("E: Unable to locate package [package]") too. All other operations that need internet access are not working. 3. I certainly see a wired network (called "eth1") at the Network Manager, and it says "Connection Established" after disconnecting and then connecting again. I have tried almost everything that could be found from google search results still no luck. Their problems slightly differ from mine or the solutions just don't work. By the way it didn't have internet access when installing Ubuntu 12.04. (I ignored the message that I need internet to install Ubuntu) Could this be a problem? I'm sorry I don't remember if internet worked or not on the previous version of Ubuntu. :( I would really appreciate your help... I don't even know what more to do if this fails too.. Thanks!! Thanks for your comment. Here is the result of ifconfig: eth0 Link encap:Ethernet HWaddr 78:ac:c0:3d:b2:b9 inet addr:10.10.65.185 Bcast:10.10.65.255 Mask:255.255.255.0 inet6 addr: fe80::7aac:c0ff:fe3d:b2b9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3907 errors:0 dropped:0 overruns:0 frame:0 TX packets:771 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:393118 (393.1 KB) TX bytes:73472 (73.4 KB) Interrupt:16 eth1 Link encap:Ethernet HWaddr 78:ac:c0:3d:b2:b8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204 (204.0 B) TX bytes:204 (204.0 B) route -n: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.10.65.1 0.0.0.0 UG 0 0 0 eth0 10.10.65.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 /etc/resolv.conf: # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 8.8.8.8 nameserver 8.8.4.4 nameserver 10.81.1.8 nameserver 10.1.2.10 nameserver 127.0.0.1 search yamatake.local /etc/network/interfaces: auto lo iface lo inet loopback #auto eth0 #iface eth0 inet dhcp #auto eth1 #iface eth1 inet dhcp And I'll also include the result of 'sudo lshw -C network' in case it might help: *-network description: Ethernet interface product: NetXtreme BCM5764M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: 78:ac:c0:3d:b2:b9 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5764m-v3.35 ip=10.10.65.185 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:93 memory:fc000000-fc00ffff *-network description: Ethernet interface product: NetXtreme BCM5764M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth1 version: 10 serial: 78:ac:c0:3d:b2:b8 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5764m-v3.35 latency=0 link=no multicast=yes port=twisted pair speed=100Mbit/s resources: irq:94 memory:fb000000-fb00ffff

  Read the article

< Previous Page | 54 55 56 57 58 59 60 61 62 63  | Next Page >