Search Results

Search found 1623 results on 65 pages for 'packet analyzers'.

Page 58/65 | < Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >

• Java: Cleaing up connection reset (but not by peer).

  - by Zombies

  There seems to be some confusion as well contradicting statements on various SO answers: http://stackoverflow.com/questions/585599/whats-causing-my-java-net-socketexception-connection-reset . You can see here that the accepted answer states that the connecteion was closed by other side. But this is not true, closing a connection doesn't cause a connection reset. It is cauesed by "an underlying TCP/IP error." What I want to know is if a SocketException: Connection reset means really besides "unerlying TCP/IP Error." What really causes this? As I doubt it has anything to do with the connection being closed (since closing a connection isn't an exception worthy flag, and reading from a closed connection is, but that isn't an "underlying TCP/IP error." My hypothesis is this Connection reset is caused from a server's failure to acknowledge an ACK packet (either wholly or just improperly as per TCP/IP). And that a SocketTimeoutException is generated only when no data is generated to be read (since this is thrown during a read after a certain duration, and read is waiting for data, but is not concerned with ACK packets). In other words, read() throws SocketTimeoutException if it didn't read any bytes of actual data (DATA LAYER) in its allotted time.

  Read the article

• Detecting TCP dropout over an unreliable network

  - by yx

  I am doing some experimentation over an unreliable radio network (home brewed) using very rudimentary java socket programming to transfer messages back and forth between the end nodes. The setup is as follows: Node A --- Relay Node --- Node B One problem I am constantly running into is that somehow the connection drops out and neither Node A or B knows that the link is dead, and yet continues to transmit data. The TCP connection does not time out either. I have added in a heartbeat message that causes a timeout after a while, but I still would like to know what is the underlying cause of why TCP does not time out. Here are the options I am enabling when setting up a socket: channel.socket().setKeepAlive(false); channel.socket().setTrafficClass(0x08); // for max throughput This behavior is strange since it is totally different than when I have a wired network. On a wired network, I can simulate a disconnected connection by pulling out the ethernet cord, however, once I plug the cord back in, the connection becomes restablished and messages begin to be passed through once more. On the radio network, the connection is never reestablished and once it silently dies, the messages never resume. Is there some other unknown java implentation or setting for a socket that I can use, also, why am I seeing this behavior in the first place? And yes, before anyone says anything, I know TCP is not the preffered choice over an unreliable network, but in this case I wanted to ensure no packet loss.

  Read the article

• SYN receives RST,ACK very frequently

  - by user1289508

  Hi Socket Programming experts, I am writing a proxy server on Linux for SQL Database server running on Windows. The proxy is coded using bsd sockets and in C, and it is working just fine. When I use a database client (written in JAVA, and running on a Linux box) to fire queries (with a concurrency of 100 or more) directly to the Database server, not experiencing connection resets. But through my proxy I am experiencing many connection resets. Digging deeper I came to know that connection from 'DB client' to 'Proxy' always succeeds but when the 'Proxy' tries to connect to the DB server the connection fails, due to the SYN packet getting RST,ACK. That was to give some background. The question is : Why does sometimes SYN receives RST,ACK? 'DB client(linux)' to 'Server(windows)' ---- Works fine 'DB client(linux) to 'Proxy(Linux)' to 'Server(windows)' ----- problematic I am aware that this can happen in "connection refused" case but this definitely is not that one. SYN flooding might be another scenario, but that does not explain fine behavior while firing to Server directly. I am suspecting some socket option setting may be required, that the client does before connecting and my proxy does not. Please put some light on this. Any help (links or pointers) is most appreciated. Additional info: Wrote a C client that does concurrent connections, which takes concurrency as an argument. Here are my observations: - At 5000 concurrency and above, some connects failed with 'connection refused'. - Below 2000, it works fine. But the actual problem is observed even at a concurrency of 100 or more. Note: The problem is time dependent sometimes it never comes at all and sometimes it is very frequent and DB client (directly to server) works fine at all times .

  Read the article

• What are the C# equivalent of these C++ structs

  - by Otake

  typedef union _Value { signed char c; unsigned char b; signed short s; unsigned short w; signed long l; unsigned long u; float f; double *d; char *p; } Value; typedef struct _Field { WORD nFieldId; BYTE bValueType; Value Value; } Field; typedef struct _Packet { WORD nMessageType; WORD nSecurityType; BYTE bExchangeId; BYTE bMarketCenter; int iFieldCount; char cSymbol[20]; Field FieldArr[1]; } Packet; What are the C# equivalent of these C++ structs? I am migrating some code from C++ to C# and having problems to migrate these structures. I had tried a few things but I always ended up having marshalling problems.

  Read the article

• Rewriting Live TCP/IP (Layer 4) Streams

  - by user213060

  I want to rewrite TCP/IP streams. Ettercap's etterfilter command lets you perform simple live replacements of TCP/IP data based on fixed strings or regexes. Example: if (ip.proto == TCP && tcp.dst == 80) { if (search(DATA.data, "gzip")) { replace("gzip", " "); msg("whited out gzip\n"); } } if (ip.proto == TCP && tcp.dst == 80) { if (search(DATA.data, "deflate")) { replace("deflate", " "); msg("whited out deflate\n"); } } http://ettercap.sourceforge.net/forum/viewtopic.php?t=2833 I would like to rewrite streams based on my own filter program instead of just simple string replacements. Anyone have an idea of how to do this? Is there anything other than Ettercap that can do live replacement like this, maybe as a plugin to a VPN software or something? The rewriting should occur at the transport layer (Layer 4) as it does in this example, instead of a lower layer packet-based approach. Thanks!

  Read the article

• Creating a assertClass() method in JUnit

  - by Mike

  Hi, I'm creating a test platform for a protocol project based on Apache MINA. In MINA when you receive packets the messageReceived() method gets an Object. Ideally I'd like to use a JUnit method assertClass(), however it doesn't exist. I'm playing around trying to work out what is the closest I can get. I'm trying to find something similar to instanceof. Currently I have: public void assertClass(String msg, Class expected, Object given) { if(!expected.isInstance(given)) Assert.fail(msg); } To call this: assertClass("Packet type is correct", SomePacket.class, receivedPacket); This works without issue, however in experimenting and playing with this my interest was peaked by the instanceof operator. if (receivedPacket instanceof SomePacket) { .. } How is instanceof able to use SomePacket to reference the object at hand? It's not an instance of an object, its not a class, what is it?! Once establishing what type SomePacket is at that point is it possible to extend my assertClass() to not have to include the SomePacket.class argument, instead favouring SomePacket?

  Read the article

• Java loop to collect the second and third elements every three in an array

  - by mhollander38

  I have a file with data in the form timestamp, coordinate, coordinate, seperated by spaces, as here; 14:25:01.215 370.0 333.0 I need to loop through and add the coordinates only to an array. The data from the file is read in and put into as String[] called info, from split(" "). I have two problems, I think the end of the file has a extra " " which I need to lose appropriately and I also want confirmation/suggestions of my loop, at the moment I am getting sporadic out of bounds exceptions. My loop is as follows; String[] info; info = dataHolder.split(" "); ArrayList<String> coOrds1 = new ArrayList<String>(); for (int counter = 0; counter < info.length; counter = counter+3) { coOrds1.add(info[counter+1]); coOrds1.add(info[counter+2]); } Help and suggestions appreciated. The text file is here but the class receives in a UDP packet from another class so I am unsure if this potentially adds " " at the end or not.

  Read the article

• Authentication system - Return information that have to change every time

  - by paulohr

  I have a application (made in Delphi) that contains a Authentication system (login & password). This system is in PHP, and the application get results from PHP using HTTP GET method. The system returns 'OK' if login and password are correct, and 'NO' if not correct. Like this... procedure Check; var x: string; begin x:=Get('www.mywebsite.com/auth.php?user=xxxxxx&pass=zzzzzz'); if x='OK' then UnlockFeatures else MessageBox(0,'You're not VIP','Error',0); end; Well, it works fine, but it is very easy to circumvent this system with sniffers, packet editor or proxy. So, I want to get some information (in PHP) that changes every time, and that could be possible get the same information by my application. What can I do? I don't need codes. Just tips, suggestions, please... Thanks...

  Read the article

• Encouter error "Linux ip -6 addr add failed" while setting up OpenVPN client

  - by Mickel

  I am trying to set up my router to use OpenVPN and have gotten quite far (I think), but something seems to be missing and I am not sure what. Here is my configuration for the client: client dev tun proto udp remote ovpn.azirevpn.net 1194 remote-random resolv-retry infinite auth-user-pass /tmp/password.txt nobind persist-key persist-tun ca /tmp/AzireVPN.ca.crt remote-cert-tls server reneg-sec 0 verb 3 OpenVPN client log: Nov 8 15:45:13 rc_service: httpd 15776:notify_rc start_vpnclient1 Nov 8 15:45:14 openvpn[27196]: OpenVPN 2.3.2 arm-unknown-linux-gnu [SSL (OpenSSL)] [LZO] [EPOLL] [MH] [IPv6] built on Nov 1 2013 Nov 8 15:45:14 openvpn[27196]: NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Nov 8 15:45:14 openvpn[27196]: Socket Buffers: R=[116736->131072] S=[116736->131072] Nov 8 15:45:14 openvpn[27202]: UDPv4 link local: [undef] Nov 8 15:45:14 openvpn[27202]: UDPv4 link remote: [AF_INET]178.132.75.14:1194 Nov 8 15:45:14 openvpn[27202]: TLS: Initial packet from [AF_INET]178.132.75.14:1194, sid=44d80db5 8b36adf9 Nov 8 15:45:14 openvpn[27202]: WARNING: this configuration may cache passwords in memory -- use the auth-nocache option to prevent this Nov 8 15:45:14 openvpn[27202]: VERIFY OK: depth=1, C=RU, ST=Moscow, L=Moscow, O=Azire Networks, OU=VPN, CN=Azire Networks, name=Azire Networks, [email protected] Nov 8 15:45:14 openvpn[27202]: Validating certificate key usage Nov 8 15:45:14 openvpn[27202]: ++ Certificate has key usage 00a0, expects 00a0 Nov 8 15:45:14 openvpn[27202]: VERIFY KU OK Nov 8 15:45:14 openvpn[27202]: Validating certificate extended key usage Nov 8 15:45:14 openvpn[27202]: ++ Certificate has EKU (str) TLS Web Server Authentication, expects TLS Web Server Authentication Nov 8 15:45:14 openvpn[27202]: VERIFY EKU OK Nov 8 15:45:14 openvpn[27202]: VERIFY OK: depth=0, C=RU, ST=Moscow, L=Moscow, O=AzireVPN, OU=VPN, CN=ovpn, name=ovpn, [email protected] Nov 8 15:45:15 openvpn[27202]: Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Nov 8 15:45:15 openvpn[27202]: Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Nov 8 15:45:15 openvpn[27202]: Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Nov 8 15:45:15 openvpn[27202]: Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Nov 8 15:45:15 openvpn[27202]: Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA Nov 8 15:45:15 openvpn[27202]: [ovpn] Peer Connection Initiated with [AF_INET]178.132.75.14:1194 Nov 8 15:45:17 openvpn[27202]: SENT CONTROL [ovpn]: 'PUSH_REQUEST' (status=1) Nov 8 15:45:17 openvpn[27202]: PUSH: Received control message: 'PUSH_REPLY,ifconfig-ipv6 2a03:8600:1001:4010::101f/64 2a03:8600:1001:4010::1,route-ipv6 2000::/3 2A03:8600:1001:4010::1,redirect-gateway def1 bypass-dhcp,dhcp-option DNS 194.1.247.30,tun-ipv6,route-gateway 178.132.77.1,topology subnet,ping 3,ping-restart 15,ifconfig 178.132.77.33 255.255.255.192' Nov 8 15:45:17 openvpn[27202]: OPTIONS IMPORT: timers and/or timeouts modified Nov 8 15:45:17 openvpn[27202]: OPTIONS IMPORT: --ifconfig/up options modified Nov 8 15:45:17 openvpn[27202]: OPTIONS IMPORT: route options modified Nov 8 15:45:17 openvpn[27202]: OPTIONS IMPORT: route-related options modified Nov 8 15:45:17 openvpn[27202]: OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified Nov 8 15:45:17 openvpn[27202]: TUN/TAP device tun0 opened Nov 8 15:45:17 openvpn[27202]: TUN/TAP TX queue length set to 100 Nov 8 15:45:17 openvpn[27202]: do_ifconfig, tt->ipv6=1, tt->did_ifconfig_ipv6_setup=1 Nov 8 15:45:17 openvpn[27202]: /usr/sbin/ip link set dev tun0 up mtu 1500 Nov 8 15:45:18 openvpn[27202]: /usr/sbin/ip addr add dev tun0 178.132.77.33/26 broadcast 178.132.77.63 Nov 8 15:45:18 openvpn[27202]: /usr/sbin/ip -6 addr add 2a03:8600:1001:4010::101f/64 dev tun0 Nov 8 15:45:18 openvpn[27202]: Linux ip -6 addr add failed: external program exited with error status: 254 Nov 8 15:45:18 openvpn[27202]: Exiting due to fatal error Any ideas are most welcome!

  Read the article

• Mac OS X Server Configure DHCP Options 66 and 67

  - by Paul Adams

  I need to configure Mountain Lion (10.8.2) OS X Server BOOTP to provide DHCP options 66 and 67 to provide PXE booting for PCs on my network. I have tried following the bootpd MAN pages, but they are not specific enough. I have also read conflicting information on the net, but nothing definitive for Mountain Lion DHCP. From bootpd man page: bootpd has a built-in type conversion table for many more options, mostly those specified in RFC 2132, and will try to convert from whatever type the option appears in the property list to the binary, packet format. For example, if bootpd knows that the type of the option is an IP address or list of IP addresses, it converts from the string form of the IP address to the binary, network byte order numeric value. If the type of the option is a numeric value, it converts from string, integer, or boolean, to the proper sized, network byte-order numeric value. Regardless of whether bootpd knows the type of the option or not, you can always specify the DHCP option using the data property list type <key>dhcp_option_128</key> <data> AAqV1Tzo </data> My TFTP server is 172.16.152.20 and the bootfile is pxelinux.0 I have edited /etc/bootpd.plist and added the following to the subnet dict: <key>dhcp_option_66</key> <data> LW4gLWUgrBCYFAo= </data> <key>dhcp_option_67</key> <data> LW4gLWUgcHhlbGludXguMAo= </data> According to the man page, the data elements are supposed to be Base64 encoded, but no matter what I try, I cannot get PXE clients to boot. I have tried encoding 172.16.152.20 using various methods: echo "172.16.152.20" | openssl enc -base64 returns MTcyLjE2LjE1Mi4yMAo= DHCP Option Code Utility (http://mac.softpedia.com/get/Internet-Utilities/DHCP-Option-Code-Utility.shtml) generating a string from 172.16.152.20 yields: LW4gLWUgMTcyLjE2LjE1Mi4yMAo= (used in the above example) DHCP Option Code Utility generating an IP Addresss from 172.16.152.20 yields: LW4gLWUgrBCYFAo= Encoding pxelinux.0 with the above methods likewise yields different encodings. I have tried using all three methods of encoding the data elements, but nothing seems to work i.e. my PXE boot clients do not get directed to my TFTP server. Can anyone help? Regards, Paul Adams.

  Read the article

• My current iptable configuration doesn't work [on hold]

  - by Brad

  sudo chkconfig iptables off /etc/init.d/iptables on ### Clear/flush iptables sudo iptables -F sudo iptables -P INPUT ACCEPT sudo iptables -P OUTPUT ACCEPT sudo iptables -P FORWARD ACCEPT ### Allow SSH iptables -A INPUT -i eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT ### Allow YUM updates sudo iptables -A OUTPUT -o eth0 -p tcp --dport 80 --match owner --uid-owner 0 --state NEW,ESTABLISHED -j ACCEPT sudo iptables -A OUTPUT -o eth0 -p tcp --dport 443 --match owner --uid-owner 0 --state NEW,ESTABLISHED -j ACCEPT ### Add your rules form the link above, here # ftp,smtp,imap,http,https,pop3,imaps,pop3s sudo iptables -A INPUT -i eth0 -p tcp -m multiport --dports 21,25,143,80,443,110,993,995 -m state --state NEW,ESTABLISHED -j ACCEPT sudo iptables -A OUTPUT -o eth0 -p tcp -m multiport --sports 21,25,143,80,110,443,993,995 -m state --state NEW,ESTABLISHED -j ACCEPT ## allow dns sudo iptables -A OUTPUT -p udp -o eth0 --dport 53 -j ACCEPT && sudo iptables -A INPUT -p udp -i eth0 --sport 53 -j ACCEPT # handling pings sudo iptables -A INPUT -p icmp --icmp-type echo-request -j ACCEPT && sudo iptables -A OUTPUT -p icmp --icmp-type echo-reply -j ACCEPT sudo iptables -A OUTPUT -p icmp --icmp-type echo-request -j ACCEPT && sudo iptables -A INPUT -p icmp --icmp-type echo-reply -j ACCEPT # manage ddos attacks sudo iptables -A INPUT -p tcp --dport 80 -m limit --limit 25/minute --limit-burst 100 -j ACCEPT ## Implement some logging so that we know what's getting dropped sudo iptables -N LOGGING sudo iptables -A INPUT -j LOGGING sudo iptables -A LOGGING -m limit --limit 2/min -j LOG --log-prefix "IPTables Packet Dropped: " --log-level 7 sudo iptables -A LOGGING -j DROP # once a rule affects traffic then it is no longer managed # so if the traffic has not been accepted, block it sudo iptables -A INPUT -j DROP sudo iptables -I INPUT 1 -i lo -j ACCEPT sudo iptables -A OUTPUT -j DROP # allow only internal port forwarding sudo iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT sudo iptables -P FORWARD DROP # create an iptables config file sudo iptables-save > /root/dsl.fw ### Append the following to the rc.local file sudo nano /etc/rc.local ####--- /sbin/iptables-restore < sudo /root/dsl.fw ####--- /etc/init.d/iptables save ## check to see if this setting is working great. sudo service iptables restart ## log out/in testing sudo chkconfig iptables on What is the problem with this setup? If I restart the server it doesn't allow me back in SSH, and there may be a problem with Yum Original source of information: https://gist.github.com/Jonathonbyrd/1274837#file-instructions

  Read the article

• Unable to mount XP share using fs-cifs from Linux

  - by MetalSearGolid

  I have a head unit that runs Linux that is connected to my PC via an Ethernet cable. I have a Windows XP share on this PC that the head unit needs to be able to mount, however, when mounting using the following command, it fails. Here is the command that fails, along with the verbose output: # fs-cifs -vvvvvvvvv -l //CUMBRIA-XP:192.168.1.2:/hnet /mnt/net cifs[2158679-1]: starting... cifs[2158679-1]: user is to input both name & passwd. cifs[2158679-1]: server [192.168.1.2] share [hnet] prefix [/mnt/net] user [nu ll] passwd [null] Welcome: 192.168.1.2(:/hnet) -> /mnt/net Username:headunit cifs[2158679-1]: user name: headunit length 8 cifs[2158679-1]: new server Password: cifs[2158679-1]: establishing connection to (192.168.1.2)CUMBRIA-XP cifs[2158679-1]: session request: 192.168.1.2:CUMBRIA-XP -> localhost cifs[2158679-1]: negotiating smb dialect cifs[2158679-1]: skey(idx=2): 00000000, challenge:(8), 6137bfa2 f2d7803b cifs[2158679-1]: negotiation: success with dialect=2 cifs[2158679-1]: logging headunit on 192.168.1.2 cifs[2158679-1]: new packet cifs[2158679-1]: returning: mid 0 status= 0 cifs[2158679-1]: smb_logon successful: dialect 2 enpass 1 cifs[2158679-1]: mounting 192.168.1.2:/hnet cifs[2158679-1]: returning: mid 1 status= 13 cifs[2158679-1]: smb_mount: Bad file descriptor cifs[2158679-1]: try upper case share. cifs[2158679-1]: session request: 192.168.1.2:CUMBRIA-XP -> localhost cifs[2158679-1]: negotiating smb dialect cifs[2158679-1]: skey(idx=2): 00000000, challenge:(8), 2d3e910f e3e148c4 cifs[2158679-1]: negotiation: success with dialect=2 cifs[2158679-1]: logging headunit on 192.168.1.2 cifs[2158679-1]: returning: mid 2 status= 0 cifs[2158679-1]: smb_logon successful: dialect 2 enpass 1 cifs[2158679-1]: mounting 192.168.1.2:/HNET cifs[2158679-1]: returning: mid 3 status= 13 cifs[2158679-1]: smb_mount: Bad file descriptor cifs[2158679-1]: mount failed. cifs[2158679-1]: io_mount: smb_connection failed: Bad file descriptor io_mount: Bad file descriptor cifs[2158679-1]: user is to input both name & passwd. fs-cifs: missing arguments, or all mount attempts failed. run "use fs-cifs" or "fs-cifs -h" for help. Any ideas? It is worthy to note that /mnt does not exist on the filesystem, but I was told by the company who gave us these units that fs-cifs should automatically create the /mnt/net folders if they don't exist.

  Read the article

• Can't ssh tunnel to access a remote mysql server

  - by hobbes3

  I can't seem to figure out why I can't use ssh tunnel to connect to my remote MySQL server. I do ssh tunnel with [hobbes3@hobbes3] ~ $ ssh linode -L 3307:localhost:3306 Then on another terminal, I try [hobbes3@hobbes3] ~ $ mysql -h localhost -P 3307 -u root --protocol=tcp -p Enter password: ERROR 2013 (HY000): Lost connection to MySQL server at 'reading initial communication packet', system error: 2 On the server, it shows this: root@li534-120 ~ # channel 4: open failed: connect failed: Connection refused Here is my my.cnf on the server: [mysqld] # Settings user and group are ignored when systemd is used (fedora >= 15). # If you need to run mysqld under different user or group, # customize your systemd unit file for mysqld according to the # instructions in http://fedoraproject.org/wiki/Systemd user=mysql datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 # Semisynchronous Replication # http://dev.mysql.com/doc/refman/5.5/en/replication-semisync.html # uncomment next line on MASTER ;plugin-load=rpl_semi_sync_master=semisync_master.so # uncomment next line on SLAVE ;plugin-load=rpl_semi_sync_slave=semisync_slave.so # Others options for Semisynchronous Replication ;rpl_semi_sync_master_enabled=1 ;rpl_semi_sync_master_timeout=10 ;rpl_semi_sync_slave_enabled=1 # http://dev.mysql.com/doc/refman/5.5/en/performance-schema.html ;performance_schema [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid [mysqld] port = 3306 socket=/var/lib/mysql/mysql.sock skip-external-locking key_buffer_size = 64M max_allowed_packet = 128M sort_buffer_size = 512K net_buffer_length = 8K read_buffer_size = 256K read_rnd_buffer_size = 512K myisam_sort_buffer_size = 8M thread_cache = 8 max_connections = 25 query_cache_size = 16M table_open_cache = 1024 table_definition_cache = 1024 tmp_table_size = 32M max_heap_table_size = 32M bind-address = 0.0.0.0 Now sure if this helps but here is the MySQL user list: mysql> select * from mysql.user; +-----------+------+-------------------------------------------+-------------+-------------+-------------+-------------+-------------+-----------+-------------+---------------+--------------+-----------+------------+-----------------+------------+------------+--------------+------------+-----------------------+------------------+--------------+-----------------+------------------+------------------+----------------+---------------------+--------------------+------------------+------------+--------------+------------------------+----------+------------+-------------+--------------+---------------+-------------+-----------------+----------------------+--------+-----------------------+ | Host | User | Password | Select_priv | Insert_priv | Update_priv | Delete_priv | Create_priv | Drop_priv | Reload_priv | Shutdown_priv | Process_priv | File_priv | Grant_priv | References_priv | Index_priv | Alter_priv | Show_db_priv | Super_priv | Create_tmp_table_priv | Lock_tables_priv | Execute_priv | Repl_slave_priv | Repl_client_priv | Create_view_priv | Show_view_priv | Create_routine_priv | Alter_routine_priv | Create_user_priv | Event_priv | Trigger_priv | Create_tablespace_priv | ssl_type | ssl_cipher | x509_issuer | x509_subject | max_questions | max_updates | max_connections | max_user_connections | plugin | authentication_string | +-----------+------+-------------------------------------------+-------------+-------------+-------------+-------------+-------------+-----------+-------------+---------------+--------------+-----------+------------+-----------------+------------+------------+--------------+------------+-----------------------+------------------+--------------+-----------------+------------------+------------------+----------------+---------------------+--------------------+------------------+------------+--------------+------------------------+----------+------------+-------------+--------------+---------------+-------------+-----------------+----------------------+--------+-----------------------+ | localhost | root | *664328D3C5E263F4FB25185681AAE7E92B01B2B0 | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | | | | | 0 | 0 | 0 | 0 | | | | 127.0.0.1 | root | *664328D3C5E263F4FB25185681AAE7E92B01B2B0 | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | | | | | 0 | 0 | 0 | 0 | | | | ::1 | root | *664328D3C5E263F4FB25185681AAE7E92B01B2B0 | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | | | | | 0 | 0 | 0 | 0 | | | +-----------+------+-------------------------------------------+-------------+-------------+-------------+-------------+-------------+-----------+-------------+---------------+--------------+-----------+------------+-----------------+------------+------------+--------------+------------+-----------------------+------------------+--------------+-----------------+------------------+------------------+----------------+---------------------+--------------------+------------------+------------+--------------+------------------------+----------+------------+-------------+--------------+---------------+-------------+-----------------+----------------------+--------+-----------------------+ 3 rows in set (0.00 sec) I read about how MySQL treats localhost vs 127.0.0.1 as connecting via a socket or TCP, respectively. But I'm starting to get confused on what's really going on or if socket vs TCP is even the issue. Thanks in advance and I'm open for any tips and suggestions! Some more info: My MySQL client, running OS X 10.8.4, is mysql Ver 14.14 Distrib 5.6.10, for osx10.8 (x86_64) using EditLine wrapper My MySQL server, running on CentOS 6.4 32-bit, is mysql> SHOW VARIABLES LIKE "%version%"; +-------------------------+--------------------------------------+ | Variable_name | Value | +-------------------------+--------------------------------------+ | innodb_version | 1.1.8 | | protocol_version | 10 | | slave_type_conversions | | | version | 5.5.28 | | version_comment | MySQL Community Server (GPL) by Remi | | version_compile_machine | i686 | | version_compile_os | Linux | +-------------------------+--------------------------------------+ 7 rows in set (0.00 sec)

  Read the article

• DNS "recursion not available" using a Cisco AnyConnect VPN connection

  - by codeape

  Does anyone have experience with configuring Cisco AnyConnect VPN? We have a problem with client DNS name resolution when connected over VPN. To me, it looks as if the Cisco AnyConnect VPN client intercepts DNS queries from the clients. Can someone confirm that the AnyConnect VPN client in fact does this (intercepts DNS traffic)? Where is this configured on the VPN server? EDIT: Here's how the routing table changes when I connect to the VPN: [~] $ diff -u /tmp/route_normal /tmp/route_vpn --- /tmp/route_normal 2010-01-20 19:23:47.000000000 +0100 +++ /tmp/route_vpn 2010-01-20 19:24:46.000000000 +0100 @@ -1,6 +1,10 @@ Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface +xxx.xxx.xx.xx.i 10.0.0.1 255.255.255.255 UGH 0 0 0 ath0 172.16.53.0 * 255.255.255.0 U 0 0 0 vmnet1 10.0.0.0 * 255.255.255.0 U 0 0 0 ath0 +172.17.20.0 * 255.255.255.0 U 0 0 0 cscotun 0 +192.168.111.0 172.17.20.212 255.255.255.0 UG 0 0 0 cscotun 0 172.16.140.0 * 255.255.255.0 U 0 0 0 vmnet8 +172.16.0.0 172.17.20.212 255.255.0.0 UG 0 0 0 cscotun 0 default 10.0.0.1 0.0.0.0 UG 0 0 0 ath0 EDIT 2: The IT guy has done "something" on the VPN endpoint. Now I get "recursion not available" when doing nslookup. The DNS servers have recursion enabled. So it must be the Cisco VPN DNS interception messing this up. ubuntu@domU-12-31-39-00-ED-14:~$ /opt/cisco/vpn/bin/vpn connect xxx.xxxxxx.xx ... >> Please enter your username and password ... >> notice: Establishing VPN... >> state: Connected >> notice: VPN session established to ... ubuntu@domU-12-31-39-00-ED-14:~$ nslookup www.vg.no ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server Server: 172.16.0.23 Address: 172.16.0.23#53 ** server can't find www.vg.no.compute-1.internal: REFUSED ubuntu@domU-12-31-39-00-ED-14:~$ ping 195.88.55.16 PING 195.88.55.16 (195.88.55.16) 56(84) bytes of data. 64 bytes from 195.88.55.16: icmp_seq=1 ttl=240 time=110 ms 64 bytes from 195.88.55.16: icmp_seq=2 ttl=240 time=111 ms 64 bytes from 195.88.55.16: icmp_seq=3 ttl=240 time=109 ms ^C --- 195.88.55.16 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2017ms rtt min/avg/max/mdev = 109.953/110.379/111.075/0.496 ms

  Read the article

• iptables (NAT/PAT) setup for SSH & Samba

  - by IanVaughan

  I need to access a Linux box via SSH & Samba that is hidden/connected behind another one. Setup :- A switch B C |----| |---| |----| |----| |eth0|----| |----|eth0| | | |----| |---| |eth1|----|eth1| |----| |----| Eg, SSH/Samba from A to C How does one go about this? I was thinking that it cannot be done via IP alone? Or can it? Could B say "hi on eth0, if your looking for 192.168.0.2, its here on eth1"? Is this NAT? This is a large private network, so what about if another PC has that IP?! More likely it would be PAT? A would say "hi 192.168.109.15:1234" B would say "hi on eth0, traffic for port 1234 goes on here eth1" How could that be done? And would the SSH/Samba demons see the correct packet header info and work?? IP info :- A - eth0 - 192.168.109.2 B - eth0 - B1 = 192.168.109.15 B2 = 172.24.40.130 - eth1 - 192.168.0.1 C - eth1 - 192.168.0.2 A, B & C are RHEL (RedHat) But Windows computers can be connected to the switch. I configured the 192.168.0.* IPs, they are changeable. Update after response from Eddie Few problems (and Machines' B IP is different!) From A :- ssh 172.24.40.130 works ok, (can get to B2) but ssh 172.24.40.130 -p 2022 -vv times out with :- OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 172.24.40.130 [172.24.40.130] port 2022. ...wait ages... debug1: connect to address 172.24.40.130 port 2022: Connection timed out ssh: connect to host 172.24.40.130 port 2022: Connection timed out From B2 :- $ service iptables status Table: filter Chain INPUT (policy ACCEPT) num target prot opt source destination Chain FORWARD (policy ACCEPT) num target prot opt source destination 1 ACCEPT tcp -- 0.0.0.0/0 192.168.0.2 tcp dpt:22 Chain OUTPUT (policy ACCEPT) num target prot opt source destination Table: nat Chain PREROUTING (policy ACCEPT) num target prot opt source destination 1 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:2022 to:192.168.0.2:22 Chain POSTROUTING (policy ACCEPT) num target prot opt source destination Chain OUTPUT (policy ACCEPT) num target prot opt source destination And ssh from B2 to C works fine :- $ ssh 192.168.0.2 Route info :- $ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 172.24.40.0 * 255.255.255.0 U 0 0 0 eth0 169.254.0.0 * 255.255.0.0 U 0 0 0 eth1 default 172.24.40.1 0.0.0.0 UG 0 0 0 eth0 $ ip route 192.168.0.0/24 dev eth1 proto kernel scope link src 192.168.0.1 172.24.40.0/24 dev eth0 proto kernel scope link src 172.24.40.130 169.254.0.0/16 dev eth1 scope link default via 172.24.40.1 dev eth0 So I just dont know why the port forward doesnt work from A to B2?

  Read the article

• Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

  - by Kevinoid

  Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated. Update (2011-06-26) After failing to solve the problem, I resorted to paid Microsoft support. They were unable to solve the problem. Since then I have implemented a solution based on Linux that is working quite well. I will attempt to evaluate any proposed answers as best I can, but current configurations and time constraints will make this slow...

  Read the article

• Guests can't access KVM host server by name although nslookup and dig returns correct record

  - by user190196

  So I have a KVM host that also runs an apache server with some yum repos. The VM guests are connected to the default virtual network, which is configured to offer DHCP and forwarding with NAT on virbr0 (192.168.12.1). The guests can successfully access the yum repos on the host by IP address, so for example curl 192.168.122.1/repo1 returns the content without problems. But I'd like to have the guests be able to reach the web server on the host by name rather IP address. I added the desired name record to the host's /etc/hosts file and libvirt's dnsmasq service seems to be serving that correctly to the guests since nslookup and dig successfully resolve the name on the guests: [root@localhost ~]# nslookup repo Server: 192.168.122.1 Address: 192.168.122.1#53 Name: repo Address: 192.168.122.1 [root@localhost ~]# dig repo ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6 <<>> repo ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 55938 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;repo. IN A ;; ANSWER SECTION: repo. 0 IN A 192.168.122.1 ;; Query time: 0 msec ;; SERVER: 192.168.122.1#53(192.168.122.1) ;; WHEN: Tue Sep 17 02:10:46 2013 ;; MSG SIZE rcvd: 38 But curl/ping/etc still fail: [root@localhost ~]# curl repo curl: (6) Couldn't resolve host 'repo' While a request via ip address works: [root@localhost ~]# curl 192.168.122.1 <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 3.2 Final//EN"> <html> <head> <title>Index of /</title> [...] Same with ping: [root@localhost ~]# ping repo ping: unknown host repo [root@localhost ~]# ping 192.168.122.1 PING 192.168.122.1 (192.168.122.1) 56(84) bytes of data. 64 bytes from 192.168.122.1: icmp_seq=1 ttl=64 time=0.110 ms 64 bytes from 192.168.122.1: icmp_seq=2 ttl=64 time=0.146 ms 64 bytes from 192.168.122.1: icmp_seq=3 ttl=64 time=0.191 ms ^C --- 192.168.122.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2298ms rtt min/avg/max/mdev = 0.110/0.149/0.191/0.033 ms I tried adding repo 192.168.122.1 to the guests' /etc/hosts files but still no dice. Also tried changing guests' /etc/nsswitch.conf with both: hosts: files dns and hosts: dns files I've read the relevant libvirt documentation and I'm not sure where else to learn more about this and be able to move forward with it.

  Read the article

• Some DHCP clients end up with wrong DNS server

  - by Nic Waller

  The scenario: DC running Windows Server 2008 R2 providing DNS + DHCP Cisco 1811 Router as the gateway 30 Windows XP DHCP clients on the LAN The problem: Some workstations are spontaneously switching to an incorrect DNS server. Specifically, ipconfig /all shows that they start using the gateway as a DNS server. This happens about 5-10 times a day to various computers, sometimes more than once per day. The workaround: Repairing the connection on the XP client always fixes the problem, and the correct DNS server address is obtained. We lost our main DNS/DHCP machine a week ago, and had to bring this one online as a spare. We've been having this issue since then. DHCP leases on the old and new servers are configured for "wired" (8 day) duration. There are definitely no other DHCP servers active on the LAN. So far there is no discernible pattern about which clients will show this problem, or when. When I ran DCDIAG /test:DNS it came back clean. Manual inspection of the DNS zone shows that all the records are appearing as expected, with no traces of the previous machine in there. Update Feb 27: Added screenshots. Here is a screenshot of the DHCP scope options on the 2008 R2 server. And here is a screenshot of ipconfig /all running on a healthy host. I don't have any ailing hosts at the moment, but will grab a screencap next time it happens. Update Feb 28: More screenshots. Here's a screenshot of DHCP and DNS traffic from a healthy client when repairing the local area connection. There's definitely only one server responding, but it does seem strange that the negotiation takes place twice. I'll try to get a similar capture from a sick machine this coming week. Update Mar 01: Caught a bad ipconfig. Here's a screenshot of ipconfig /all from a client that had this issue. It says the lease was issued this morning, but it doesn't even have an entry for the secondary DNS I set up yesterday. Both DNS servers were discovered properly when repairing the connection. Update Mar 01: It even got the sysadmin! This issue finally affected my personal workstation this morning. Unfortunately I had just rebooted and wasn't running a packet dump at the time. I set up a secondary server yesterday, and was logging all DNS traffic to it. My machine had not contacted the secondary DNS in over half an hour, so that says to me that it's just spontaneously reverting to the gateway without even failing over to secondary DNS first. Today I swapped the order of the DNS servers in DHCP, so the secondary is primary and vice versa. I will update again once I know how that goes.

  Read the article

• 6to4 tunnel: cannot ping6 to ipv6.google.com?

  - by quanta

  Hi folks, Follow the Setup of 6to4 tunnel guide, I want to test ipv6 connectivity, but I cannot ping6 to ipv6.google.com. Details below: # traceroute 192.88.99.1 traceroute to 192.88.99.1 (192.88.99.1), 30 hops max, 40 byte packets 1 static.vdc.vn (123.30.53.1) 1.514 ms 2.622 ms 3.760 ms 2 static.vdc.vn (123.30.63.117) 0.608 ms 0.696 ms 0.735 ms 3 static.vdc.vn (123.30.63.101) 0.474 ms 0.477 ms 0.506 ms 4 203.162.231.214 (203.162.231.214) 11.327 ms 11.320 ms 11.312 ms 5 static.vdc.vn (222.255.165.34) 11.546 ms 11.684 ms 11.768 ms 6 203.162.217.26 (203.162.217.26) 42.460 ms 42.424 ms 42.401 ms 7 218.188.104.173 (218.188.104.173) 42.489 ms 42.462 ms 42.415 ms 8 218.189.5.10 (218.189.5.10) 42.613 ms 218.189.5.42 (218.189.5.42) 42.273 ms 42.300 ms 9 d1-26-224-143-118-on-nets.com (118.143.224.26) 205.752 ms d1-18-224-143-118-on-nets.com (118.143.224.18) 207.130 ms d1-14-224-143-118-on-nets.com (118.143.224.14) 206.970 ms 10 218.189.5.150 (218.189.5.150) 207.456 ms 206.349 ms 206.941 ms 11 * * * 12 10gigabitethernet2-1.core1.lax1.he.net (72.52.92.121) 214.087 ms 214.426 ms 214.818 ms 13 192.88.99.1 (192.88.99.1) 207.215 ms 199.270 ms 209.391 ms # ifconfig tun6to4 tun6to4 Link encap:IPv6-in-IPv4 inet6 addr: 2002:x:x::/16 Scope:Global inet6 addr: ::x.x.x.x/128 Scope:Compat UP RUNNING NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:11 dropped:0 overruns:0 carrier:11 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) # iptunnel sit0: ipv6/ip remote any local any ttl 64 nopmtudisc tun6to4: ipv6/ip remote any local x.x.x.x ttl 64 # ip -6 route show ::/96 via :: dev tun6to4 metric 256 expires 21332777sec mtu 1480 advmss 1420 hoplimit 4294967295 2002::/16 dev tun6to4 metric 256 expires 21332794sec mtu 1480 advmss 1420 hoplimit 4294967295 fe80::/64 dev eth0 metric 256 expires 15674592sec mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth1 metric 256 expires 15674597sec mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tun6to4 metric 256 expires 21332794sec mtu 1480 advmss 1420 hoplimit 4294967295 default via ::192.88.99.1 dev tun6to4 metric 1 expires 21332861sec mtu 1480 advmss 1420 hoplimit 4294967295 # ping6 -n -c 4 ipv6.google.com PING ipv6.google.com(2404:6800:8005::68) 56 data bytes From 2002:x:x:: icmp_seq=0 Destination unreachable: Address unreachable From 2002:x:x:: icmp_seq=1 Destination unreachable: Address unreachable From 2002:x:x:: icmp_seq=2 Destination unreachable: Address unreachable From 2002:x:x:: icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 4 packets transmitted, 0 received, +4 errors, 100% packet loss, time 2999ms What is my problem? Thanks,

  Read the article

• Total newb having SSH tunnel and remote MySQL access problems

  - by kscott

  I don't often work with linux or need to SSH tunnel into remote MySQL databases, so pardon my ignorance. I'm using Windows 7 and am needing to connect to a remote MySQL instance on a Linux server. For months I had been using the HeidiSQL client application successfully. Today two things happened: the DB moved to a new server and I updated HeidiSQL, now I cannot log in to the MySQL server, when attempting I get this message from Heidi: SQL Error (2003) in statement #0: Can't connect to MySQL server on 'localhost' (10061) If I use Putty, I can connect to the server and get MySQL access through command line, including fetching data from the DB. I assume this means my credentials and address are correct, but do not understand why putting those same details into HeidiSQL's SSH tunnel info won't work. I also downloaded the MySQL Workbench and attempted to set up a connection through that client and got this message: Cannot Connect to Database Server Your connection attempt failed for user 'myusername' from your host to server at localhost:3306: Lost connection to MySQL server at 'reading initial communication packet', system error: 0 Please: 1 Check that mysql is running on server localhost 2 Check that mysql is running on port 3306 (note: 3306 is the default, but this can be changed) 3 Check the myusername has rights to connect to localhost from your address (mysql rights define what clients can connect to the server and from which machines) 4 Make sure you are both providing a password if needed and using the correct password for localhost connecting from the host address you're connecting from From Googling around I see that it could be related to the MySQL bind-address, but I am a third party sub-contractor with no access to the MySQL settings of this box and the system admin is assuring me that I'm an idiot and need to figure it out on my end. This is completely possible but I don't know what else to try. Edit 1 - The client settings I am using In Heidi and MySQL Workbench I am using the following: SSH host + port: theHostnameOfTheRemoteServer.com:22 {this is the same host I can Putty to} SSH Username: mySSHusername {the same user name I use for my Putty connection} SSH Password: mySSHpassword {the same password for the Putty connection} Local port: 3307 {this is on the SSH settings tab and was defaulted to 3307 by Heidi, changing it to 3306 gives me a different error: SQL Error (1045) in statement #0: Access denied for user 'mySQLusername'@'localhost' (using password: YES)"} MySQL host: theHostnameOfTheRemoteServer.com {consensus seems to be I should use 'localhost' here} MySQL User: mySQLusername {which I can connect with once in with Putty} MySQL Password: mySQLpassword {which works once in with Putty} Port: 3306

  Read the article

• radvd is not assigning prefix

  - by Samik

  I'm currently trying to setup IPv6 address auto-configuration with router advertisement daemon (radvd) on a virtual machine running CentOS 6.5. But the eth0 interface is not obtaining that prefix. I've obtained the ULA prefix from here. Contents of /etc/sysctl.conf # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 net.ipv6.conf.all.forwarding = 1 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 0 # Controls whether core dumps will append the PID to the core filename. # Useful for debugging multi-threaded applications. kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Disable netfilter on bridges. net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 # Controls the default maxmimum size of a mesage queue kernel.msgmnb = 65536 # Controls the maximum size of a message, in bytes kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 Contents of /etc/radvd.conf # NOTE: there is no such thing as a working "by-default" configuration file. # At least the prefix needs to be specified. Please consult the radvd.conf(5) # man page and/or /usr/share/doc/radvd-*/radvd.conf.example for help. # # interface eth0 { AdvSendAdvert on; MinRtrAdvInterval 3; MaxRtrAdvInterval 10; AdvDefaultPreference low; AdvHomeAgentFlag off; prefix fd8a:8d9d:808f:1::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr on; }; }; Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes I've also enabled radvd at startup through chkconfig. Though I noticed that radvd is starting after interfaces are brought up. I've tried restarting the network service afterwards but still I get the following link-local address only #ip -6 addr show 1: lo: mtu 16436 inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qlen 1000 inet6 fe80::5054:ff:fe74:d746/64 scope link valid_lft forever preferred_lft forever Edit: Based on the answer given by Sander Steffann I still need clarification on some points but I'm posting here what worked. Contents of /etc/sysconfig/network NETWORKING=yes HOSTNAME=syslog-ng-server NETWORKING_IPV6=yes IPV6FORWARDING=yes Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes IPV6FORWARDING=no Removed following line from /etc/sysctl.conf net.ipv6.conf.all.forwarding = 1 Contents of /etc/radvd.conf is as previous.

  Read the article

• How do I protect a low budget network from rogue DHCP servers?

  - by Kenned

  I am helping a friend manage a shared internet connection in an apartment buildling with 80 apartments - 8 stairways with 10 apartments in each. The network is laid out with the internet router at one end of the building, connected to a cheap non-managed 16 port switch in the first stairway where the first 10 apartments are also connected. One port is connected to another 16 port cheapo switch in the next stairway, where those 10 apartments are connected, and so forth. Sort of a daisy chain of switches, with 10 apartments as spokes on each "daisy". The building is a U-shape, approximately 50 x 50 meters, 20 meters high - so from the router to the farthest apartment it’s probably around 200 meters including up-and-down stairways. We have a fair bit of problems with people hooking up wifi-routers the wrong way, creating rogue DHCP servers which interrupt large groups of the users and we wish to solve this problem by making the network smarter (instead of doing a physical unplugging binary search). With my limited networking skills, I see two ways - DHCP-snooping or splitting the entire network into separate VLANS for each apartment. Separate VLANS gives each apartment their own private connection to the router, while DHCP snooping will still allow LAN gaming and file sharing. Will DHCP snooping work with this kind of network topology, or does that rely on the network being in a proper hub-and-spoke-configuration? I am not sure if there are different levels of DHCP snooping - say like expensive Cisco switches will do anything, but inexpensive ones like TP-Link, D-Link or Netgear will only do it in certain topologies? And will basic VLAN support be good enough for this topology? I guess even cheap managed switches can tag traffic from each port with it’s own VLAN tag, but when the next switch in the daisy chain receives the packet on it’s “downlink” port, wouldn’t it strip or replace the VLAN tag with it’s own trunk-tag (or whatever the name is for the backbone traffic). Money is tight, and I don’t think we can afford professional grade Cisco (I have been campaigning for this for years), so I’d love some advice on which solution has the best support on low-end network equipment and if there are some specific models that are recommended? For instance low-end HP switches or even budget brands like TP-Link, D-Link etc. If I have overlooked another way to solve this problem it is due to my lack of knowledge. :)

  Read the article

• Persuading openldap to work with SSL on Ubuntu with cn=config

  - by Roger

  I simply cannot get this (TLS connection to openldap) to work and would appreciate some assistance. I have a working openldap server on ubuntu 10.04 LTS, it is configured to use cn=config and most of the info I can find for TLS seems to use the older slapd.conf file :-( I've been largely following the instructions here https://help.ubuntu.com/10.04/serverguide/C/openldap-server.html plus stuff I've read here and elsewhere - which of course could be part of the problem as I don't totally understand all of this yet! I have created an ssl.ldif file as follows; dn:cn=config add: olcTLSCipherSuite olcTLSCipherSuite: TLSV1+RSA:!NULL add: olcTLSCRLCheck olcTLSCRLCheck: none add: olcTLSVerifyClient olcTLSVerifyClient: never add: olcTLSCACertificateFile olcTLSCACertificateFile: /etc/ssl/certs/ldap_cacert.pem add: olcTLSCertificateFile olcTLSCertificateFile: /etc/ssl/certs/my.domain.com_slapd_cert.pem add: olcTLSCertificateKeyFile olcTLSCertificateKeyFile: /etc/ssl/private/my.domain.com_slapd_key.pem and I import it using the following command line ldapmodify -x -D cn=admin,dc=mydomain,dc=com -W -f ssl.ldif I have edited /etc/default/slapd so that it has the following services line; SLAPD_SERVICES="ldap:/// ldapi:/// ldaps:///" And everytime I'm making a change, I'm restarting slapd with /etc/init.d/slapd restart The following command line to test out the non TLS connection works fine; ldapsearch -d 9 -D cn=admin,dc=mydomain,dc=com -w mypassword \ -b dc=mydomain,dc=com -H "ldap://mydomain.com" "cn=roger*" But when I switch to ldaps using this command line; ldapsearch -d 9 -D cn=admin,dc=mydomain,dc=com -w mypassword \ -b dc=mydomain,dc=com -H "ldaps://mydomain.com" "cn=roger*" This is what I get; ldap_url_parse_ext(ldaps://mydomain.com) ldap_create ldap_url_parse_ext(ldaps://mydomain.com:636/??base) ldap_sasl_bind ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP mydomain.com:636 ldap_new_socket: 3 ldap_prepare_socket: 3 ldap_connect_to_host: Trying 127.0.0.1:636 ldap_pvt_connect: fd: 3 tm: -1 async: 0 TLS: can't connect: A TLS packet with unexpected length was received.. ldap_err2string ldap_sasl_bind(SIMPLE): Can't contact LDAP server (-1) Now if I check netstat -al I can see; tcp 0 0 *:www *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:https *:* LISTEN tcp 0 0 *:ldaps *:* LISTEN tcp 0 0 *:ldap *:* LISTEN I'm not sure if this is significant as well ... I suspect it is; openssl s_client -connect mydomain.com:636 -showcerts CONNECTED(00000003) 916:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:s23_lib.c:188: I think I've made all my certificates etc OK and here are the results of some checks; If I do this; certtool -e --infile /etc/ssl/certs/ldap_cacert.pem I get Chain verification output: Verified. certtool -e --infile /etc/ssl/certs/mydomain.com_slapd_cert.pem Gives "certtool: the last certificate is not self signed" but it otherwise seems OK? Where have I gone wrong? Surely getting openldap to run securely on ubuntu should be easy and not require a degree in rocket science! Any ideas?

  Read the article

• Tutorial for configuring OpenVPN [on hold]

  - by user2699451

  I have been through 10+ tutorials on setting up a OpenVPN, and each tutorial gives a different problem... Does anyone know of a decent and helpful website/tutorial which I could go to to get it set up? I have been battling through it for almost 2 months now. Yes, I have also bugged forums.openvpn, but I think I have "reached my post limit" with them. I have to configure it remotely via ssh. UPDATE: okay, I have been asked to be more clear on the topic I followed this tutorial (as a example) - http://www.servermom.com/how-to-build-openvpn-server-on-centos-6-x/732/ I had no issues setting up, etc. except when I boot into windows and run the OpenVPN GUI Client, it connects and gives this error: WARNING: Bad encapsulated packet length from peer (21331), which must be 0 and <= 1576 -- please ensure that --tun-mtu or --link-mtu is equal on both peers -- this condition could also indicate a possible active attack on the TCP link -- [Attemping restart...] Here is my server config: port 1194 #- port proto udp #- protocol dev tun tun-mtu 1500 tun-mtu-extra 32 mssfix 1450 reneg-sec 0 ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem plugin /usr/lib64/openvpn/plugin/lib/openvpn-auth-pam.so /etc/pam.d/login #- Co$ #plugin /etc/openvpn/radiusplugin.so /etc/openvpn/radiusplugin.cnf #- Uncomment$ client-cert-not-required username-as-common-name server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" keepalive 5 30 comp-lzo persist-key persist-tun status 1194.log verb 3 and my client config: client dev tun proto udp remote [server ip] 1194 # - Your server IP and OpenVPN Port resolv-retry infinite nobind tun-mtu 1500 tun-mtu-extra 32 mssfix 1450 persist-key persist-tun ca ca.crt auth-user-pass comp-lzo reneg-sec 0 verb 3 OpenVPN Client Log: Thu Oct 31 11:51:29 2013 OpenVPN 2.0.9 Win32-MinGW [SSL] [LZO] built on Oct 1 2006 Thu Oct 31 11:51:44 2013 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Thu Oct 31 11:51:44 2013 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Thu Oct 31 11:51:44 2013 LZO compression initialized Thu Oct 31 11:51:44 2013 Control Channel MTU parms [ L:1576 D:140 EF:40 EB:0 ET:0 EL:0 ] Thu Oct 31 11:51:44 2013 Data Channel MTU parms [ L:1576 D:1450 EF:44 EB:135 ET:32 EL:0 AF:3/1 ] Thu Oct 31 11:51:44 2013 Local Options hash (VER=V4): '2547efd2' Thu Oct 31 11:51:44 2013 Expected Remote Options hash (VER=V4): '77cf0943' Thu Oct 31 11:51:44 2013 Attempting to establish TCP connection with x.x.x.x:1194 Thu Oct 31 11:51:44 2013 TCP connection established with x.x.x.x:1194 Thu Oct 31 11:51:44 2013 TCPv4_CLIENT link local: [undef] Thu Oct 31 11:51:44 2013 TCPv4_CLIENT link remote: x.x.x.x:1194 // after this it just hangs, nothing happens So I dont know what I am doing wrong but I am getting a bit impatient and on each forum I post this, I get stupid/unrelated/unhelpful answers...

  Read the article

• Block IP Address including ICMP using UFW

  - by dr jimbob

  I prefer ufw to iptables for configuring my software firewall. After reading about this vulnerability also on askubuntu, I decided to block the fixed IP of the control server: 212.7.208.65. I don't think I'm vulnerable to this particular worm (and understand the IP could easily change), but wanted to answer this particular comment about how you would configure a firewall to block it. I planned on using: # sudo ufw deny to 212.7.208.65 # sudo ufw deny from 212.7.208.65 However as a test that the rules were working, I tried pinging after I setup the rules and saw that my default ufw settings let ICMP through even from an IP address set to REJECT or DENY. # ping 212.7.208.65 PING 212.7.208.65 (212.7.208.65) 56(84) bytes of data. 64 bytes from 212.7.208.65: icmp_seq=1 ttl=52 time=79.6 ms ^C --- 212.7.208.65 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 79.630/79.630/79.630/0.000 ms Now, I'm worried that my ICMP settings are too generous (conceivably this or a future worm could setup an ICMP tunnel to bypass my firewall rules). I believe this is the relevant part of my iptables rules is given below (and even though grep doesn't show it; the rules are associated with the chains shown): # sudo iptables -L -n | grep -E '(INPUT|user-input|before-input|icmp |212.7.208.65)' Chain INPUT (policy DROP) ufw-before-input all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-input (1 references) ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 3 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 4 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 11 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 12 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 ufw-user-input all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-input (1 references) DROP all -- 0.0.0.0/0 212.7.208.65 DROP all -- 212.7.208.65 0.0.0.0/0 How should I go about making it so ufw blocks ICMP when I specifically attempt to block an IP address? My /etc/ufw/before.rules has in part: # ok icmp codes -A ufw-before-input -p icmp --icmp-type destination-unreachable -j ACCEPT -A ufw-before-input -p icmp --icmp-type source-quench -j ACCEPT -A ufw-before-input -p icmp --icmp-type time-exceeded -j ACCEPT -A ufw-before-input -p icmp --icmp-type parameter-problem -j ACCEPT -A ufw-before-input -p icmp --icmp-type echo-request -j ACCEPT I'm tried changing ACCEPT above to ufw-user-input: # ok icmp codes -A ufw-before-input -p icmp --icmp-type destination-unreachable -j ufw-user-input -A ufw-before-input -p icmp --icmp-type source-quench -j ufw-user-input -A ufw-before-input -p icmp --icmp-type time-exceeded -j ufw-user-input -A ufw-before-input -p icmp --icmp-type parameter-problem -j ufw-user-input -A ufw-before-input -p icmp --icmp-type echo-request -j ufw-user-input But ufw wouldn't restart after that. I'm not sure why (still troubleshooting) and also not sure if this is sensible? Will there be any negative effects (besides forcing the software firewall to force ICMP through a few more rules)?

  Read the article

< Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >