Search Results

Search found 17913 results on 717 pages for 'old school rules'.

Page 584/717 | < Previous Page | 580 581 582 583 584 585 586 587 588 589 590 591  | Next Page >

• Netgear router keeps disconnecting iPhone

  - by DisgruntledGoat

  My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

  Read the article

• Windows Server 2008 - inexplicable system time jumps/glitches/inaccuracies

  - by Nathan Ridley

  I'm running a production web server on Windows Server 2008. On this server I have a database which logs certain user actions, but every now and again I inexplicably get database entries which, according to the record ID and the records immediately before and after, have the wrong time logged against them (7 days+ too old). For example, record ID 1001 will be for Dec 7, 11pm, 1002 will be for Dec 7, 11:01pm, then 1003 will be for Nov 28, 1:38am, then the next will be back on track again. The problem seems to occur in random records (or 2-3 records in a row) and crops up once every few days. This is absolutely baffling because there is only one place in the application that assigns this date/time value and it's simply the system UTC date. I have been synchronizing the system time to time-a.nist.gov (which I read in another article was a bit more reliable than the default time.windows.com) and it seems to occasionally get out of time anyway (3-4 minutes), but I'm speculating that occasionally the time server has a temporary glitch where the date changes to a drastically wrong value for a short space of time, then changes back. Either that, or the motherboard clock battery is screwed and the reason the time momentarily changes is that the motherboard loses the time and then the time synchronization puts it back again. Could either of my suspicions be right? Should I turn off time synchronization for a production server? Assigning dates to an event log where the dates are up to 2 weeks prior to the actual date is a severe problem I can't have when the next version of my application is released. Any suggestions or advice would be appreciated.

  Read the article

• What's the best / easiest way to combine two mailboxes on Exchange 2007?

  - by jmassey

  I've found this and this(2) (sorry, maximum hyperlink limit for new users is 1, apparently), but they both seem targeted toward much more complex cases than what I'm trying to do, and I just want to make sure I'm not missing some better approach. Here's the scenario: 'Alice' has retired. 'Bob' has taken over Alice's position. Bob was already with the organization in a different but related position, and so they already have their own Exchange account with mail, calendars, etc., that they need to keep. I need to get all of Alice's old mail, calendar entries, etc., merged into Bob's existing stuff. Ideally, I don't want to have all of Alice's stuff in a separate 'recovery' folder that Bob would have to switch back and forth between to look at older stuff; I want it all just merged into Bob's current Inbox / Calendar. I'm assuming (read: hoping) that there's a better way to do this than fiddling with permissions and exporting to and then importing from a .pst. Office version is 2007 for everybody that uses Exchange, if that helps. Exchange is version 8.1. What (preferably step-by-step - I'm new to Exchange) is the best way to do this? I can't imagine this is an uncommon scenario, but my google-fu has failed me; there seems to be nothing on this subject that isn't geared towards far more complex scenarios. (2): h t t p://technet.microsoft.com/en-us/library/bb201751%28EXCHG.80%29.aspx

  Read the article

• ESXi 5 Guests will not boot

  - by Adrian

  I have a problem with Guests not booting under VMWare ESXi 5.0 on my IBM x3550M3 server. Note: Investigation eventually determined that problem was with the VMware client on a Lenovo Edge laptop, the only Windows box available in a Linux IT shop. vSphere Client v4 and v5 duplicated behavior on the Lenovo Edge. As indicated in the comment to the accepted answer, replacing the workstation with one using different video was the "fix" for this particular issue. The ESXi host boots just fine. The Client connects just fine. Guests can be configured but do not successfully boot. The initial guest memory consumption jumps up to 560MB and drops down to 40MB after a few seconds. Initial CPU usage is 1 full CPU (3000Ghz per the chart) and immediately drops downm to 29Mhz. Guests do not display any output in the Console tab but show a state of 'Powered On'. No errors in the Events tab. Switching Guest from BIOS to EFI makes no difference. VMs are listed as Version 7 and the behavior is duplicated across all availabled Guest OS flavors. Problem also duplicated when server is booted up in Legacy Only mode. Logs do not contain anything particularly suspicious. Edit: No firewalls, routers, or VLANs in between the client and server. Edit 2: We have tried to Boot Guest into BIOS screen at Next Boot checkbox in the Guest Setting. Was not successful. Edit 3: 500GB datastore with 1 40GB VM on it. Plenty of space. Edit 4: Guests copied from my old ESXi 4 server DO NOT boot on the ESXi 5 system. Initially it complains about too little Video RAM being configured for the default 2500x1600, but it still doesn't work properly even after I bump the Video RAM settings or switch it to Auto-Detect.

  Read the article

• How to set TV-out options under Linux of an Geforce 9600 GT video card

  - by polemon

  I'm using the TV-out connector of my Geforce 9600 GT to connect it to an old TV set. It's obviously in Composite mode, the other two cables of Component video are dead, only Pb/VIDEO labeled one gives me a signal. The picture appears black/white on the TV, I presume it's because the video card gives me an NTSC signal, but it's a PAL tv set. How do I change the TV-out from NTSC to PAL? My Component to SCART adapter hasn't arrived yet, but I think I should be able to set manually, whether the signal should be Composite or Component. How do I switch modes of the TV-out, between Component and Composite? I'm running Linux, so it's probably some settings I need to make in xorg.conf. Edit: I got this far: I need to set in the "Device" section of my xorg.conf: Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" The whole section looks like this now: Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 9600 GT" Option "AddARGBGLXVisuals" "True" Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" EndSection How can I list all available settings for "TVStandard" and "TVOutFormat"?

  Read the article

• Heartbeat/DRBD failover didn't work as expected. How do I make the failover more robust?

  - by Quinn Murphy

  I had a scenario where a DRBD-heartbeat set up had a failed node but did not failover. What happened was the primary node had locked up, but didn't go down directly (it was inaccessible via ssh or with the nfs mount, but it could be pinged). The desired behavior would have been to detect this and failover to the secondary node, but it appears that since the primary didn't go full down (there is a dedicated network connection from server to server), heartbeat's detection mechanism didn't pick up on that and therefore didn't failover. Has anyone seen this? Is there something that I need to configure to have more robust cluster failover? DRBD seems to otherwise work fine (had to resync when I rebooted the old primary), but without good failover, it's use is limited. heartbeat 3.0.4 drbd84 RHEL 6.1 We are not using Pacemaker nfs03 is the primary server in this setup, and nfs01 is the secondary. ha.cf # Hearbeat Logging logfacility daemon udpport 694 ucast eth0 192.168.10.47 ucast eth0 192.168.10.42 # Cluster members node nfs01.openair.com node nfs03.openair.com # Hearbeat communication timing. # Sets the triggers and pulse time for swapping over. keepalive 1 warntime 10 deadtime 30 initdead 120 #fail back automatically auto_failback on and here is the haresources file: nfs03.openair.com IPaddr::192.168.10.50/255.255.255.0/eth0 drbddisk::data Filesystem::/dev/drbd0::/data::ext4 nfs nfslock

  Read the article

• unable to copy file to folder, permission denied without explanation

  - by ValekHalfHeart

  Recently Norton Internet security deleted ml.exe (an assembler I use to program in masm32) off of my computer, thinking that one of the programs I had written with it was a virus (it was most certainly not). Fortunately, I had a copy of ml.exe backed up in an external hard drive, and tried to copy it over to my computer. The old ml.exe was located in C:\masm32\bin, so I tried to copy the new one to that location. After disabling Norton (which had opened the folder and preventing me from accessing it), I am still unable to copy the new file to C:\masm32\bin. When I tried, Windows announced that I would need Administrator permission to copy the file. Since I'm an admin, I figured this wouldn't be a problem although it was unexpected, as I have never had to provide administrator permission to access this folder before. However, instead of prompting me to enter my password, Windows simply refuses to copy the file: I repeat, I was not asked to provide a password. It simply says that I do not have permission. Does anyone know what's happening and how to fix it? Is Norton still causing problems, or it something else?

  Read the article

• Can I share my cable internet connection through my ADSL wireless router?

  - by Roaders

  Hi All Over the xmas period I am at my in-laws. They have Virgin Broadband (cable) and have a basic modem / router that is plugged directly into their computer using an ethernet cable. My wife and I arrived with 5 PCs! (ok, one is a gift and won't be used) 4 of which are laptops so I would like to be able to use their internet connection. At the moment I am working so have plugged the ethernet cable into my work laptop. Rebooting the router meant that my work laptop now has internet. I have my ADSL Netgear router which is wireless. I tried plugging it in between the router and the PC but I didn't seem to be able to share the internet connection wirelessly. The original PC still had internet despite ony being connected to my router but my wireless laptop didn't have a connection. My old cable router had an internet ethernet port on the back that the modem plugged into. My ADSL router doesn't, it has a phone connection socket. Is there a way of doing what I want with the equipment I have? Thanks

  Read the article

• RHEL 6 vs latest vanilla kernel differences?

  - by Yanko Hernández Álvarez

  What are the differences of the RHEL 6 kernel and the latest kernel.org one? I know RHEL is based on 2.6.32 with some features backported from newer kernels and that it also has other features that are not yet part of the latest vanilla kernel. Is there any comparison of the features of both kernels so I can tell how advanced is the RHEL kernel 6 vs. latest vanilla and vice versa?. It don't have to be the latest kernel at all, but the more recent the vanilla version, the better. What I want to know is: What features I lose/win if I change the RHEL kernel for the latest kernel.org’s one? What features are less matured/developed in the latest vanilla kernel than in RHEL’s (and vice versa)? (I guess KVM virtualization is one of them, but I'm not so sure.) What things (libraries / programs / etc) don’t interact as well with the latest vanilla kernel than with the RHEL’s one? In a related note: Is there ANY way to be as up to date (kernelwise) as possible (using RHEL 6) without loosing too much in the process? (Any way except doing the patching myself, I don’t have the necessary expertise) Any repo I don’t know of? Any alternative? Update: The srpm doesn't include patches (see comments), so that way is not possible. Clarification: I'm interested in how "old" the RHEL kernel gets as time goes by, and to know when the latest upstream kernel includes all the improvements included in the RHEL version.

  Read the article

• How to back up a database with thousands of files

  - by Neal

  I am working with a Fedora server that runs a customized software package. The server software is quite old, and its database consists of 1,723 files. The database files are constantly changing - they continually grow and changes are not necessarily appended to the end. So right now, we currently back up every 24 hours at midnight when all users are off of the system and the database is in an internally consistent state. The problem is that we have the potential to lose an entire day's worth of work, which would be unrecoverable. So I'd like to know if there is a way to take some sort of an instantaneous snapshot of these database files that we could back up every 30 minutes or so. I've read about Linux LVM snapshots, and am thinking that I might be able to do accomplish the goal by taking a snapshot, rsync'ing the files to a backup server, then dropping the snapshot. But I've never done this before,so I don't know if this is the "right" fix. Any ideas on this? Any better solutions? Thanks!

  Read the article

• Moving server room to another part of the building

  - by PHLiGHT

  This question is a bit different than the typical we are moving our server room to an off site location or we are moving the whole office to a new building. Management wants to add some more office space and to do so they want to move the server room to another location. The server room has Verizon smart jacks, a few servers, PBX and all the office network drops go into this room. I'm going to go over there to scout out an alternate location for the equipment because that is still TBD. This sounds like quite a pain since the Verizon equipment for our MPLS will need to be moved (never done that) and the office jacks will need to be re-run. How do you handle the jacks? I was thinking of keeping them in the same location and having new wall plates put in with half the ports going to the current location and the other half to the new location. Or do you think that 40 drops could just be done over the weekend so the old stuff would be ripped out and replaced with the new? Currently the wiring is a mess so this could be a blessing in the long run.

  Read the article

• Updated my WAMP Server and MySQL is eating up 580mB of memory

  - by Jon

  I updated my dev-box's WAMPSERVER, and along with updating PHP and Apache, MySQL updated to '5.6.12'. After doing that, I copied the data folder from my old (5.1.36) install to the new one and now MySQL takes up 580mB which is way too much, since I'm the only person using it (Locally) and there are only 20 or so databases on it, none of which have 'memory' tables. How can I get this down to a decent amount? My my.ini: # For advice on how to change settings please see # http://dev.mysql.com/doc/refman/5.6/en/server-configuration-defaults.html # *** DO NOT EDIT THIS FILE. It's a template which will be copied to the # *** default location during install, and will be replaced if you # *** upgrade to a newer version of MySQL. [mysqld] # Remove leading # and set to the amount of RAM for the most important data # cache in MySQL. Start at 70% of total RAM for dedicated server, else 10%. # innodb_buffer_pool_size = 128M # Remove leading # to turn on a very important data integrity option: logging # changes to the binary log between backups. # log_bin # These are commonly set, remove the # and set as required. # basedir = ..... # datadir = ..... # port = ..... # server_id = ..... # Remove leading # to set options mainly useful for reporting servers. # The server defaults are faster for transactions and fast SELECTs. # Adjust sizes as needed, experiment to find the optimal values. # join_buffer_size = 128M # sort_buffer_size = 2M # read_rnd_buffer_size = 2M sql_mode=NO_ENGINE_SUBSTITUTION,STRICT_TRANS_TABLES Database info: Storage Engine Data Size Index Size Total Size InnoDB 48.00 KB 0.00 B 48.00 KB MEMORY 0.00 B 0.00 B 0.00 B MyISAM 163.64 MB 122.49 MB 286.13 MB Total 163.69 MB 122.49 MB 286.18 MB

  Read the article

• Cannot delete flash9.ocx

  - by Kara Marfia

  Some kinda voodoo, indeed. Bought a new boot drive, and it's time to use the old drive for data. I thought I'd save some time by just wiping the unneeded system folders, instead of backing up, formatting, and restoring. Wups! I have a single Adobe file that absolutely will not be deleted. G:\Windows\SysWOW64\Macromed\Flash\flash9.ocx - though it may have started with a different file name. I'm able to rename it, oddly enough. To be clear, the drive is currently plugged in externally. So I can boot the computer, plug this drive in afterward, and immediately attempt to delete. "File in use" box reads "the action can't be completed because the file is open in another program". I'd format at this point, but it's my white whale, and I have to know if Adobe has inserted some nasty little registry hack - or whatever it is - making this impossible. Since I'm sure it'll come up, I've taken ownership of the file - and this was the trick preventing me from deleting anything else on the drive - full rights on the file permissions, you name it, I've fiddled with the file itself. I'm about to try uninstalling flash from the system drive, in case that aligns the planets properly. Sometimes I wish I were less stubborn, and could just format already.

  Read the article

• Sending bulkmail from different server?

  - by Omer Gencay

  I want to send bulk domains from my vps for a domain(cagetur.com) hosted in another company. The company(cagetur) will go on using the old hosting account for its mailing operations. The vps will just be used for smtp for once a week. I created an A record "vps.cagetur.com". directed it to the IP adress of vps then created a mx record with bigger preference number "50 vps.cagetur.com." on the domain control panel. When I trace the "vps.cagetur.com" i can reach my vps now. I installed hMail on the vps. Configure it (created domain, accounts). I have no information about "system" so i couldn't get further from this point. I can connect to the mail server with Outlook without errors. I can send an email from the account on the vps but it doesn't reaches. No errors, no emails. What do i have to do for getting it work? Thank you.

  Read the article

• Encrypted WiFi with no password?

  - by Ian Boyd

  Is there any standard that allows a WiFi connection to be encrypted, but not require a password? i know that (old, weak) WEP, and newer WPA/WPA2 require a password (i.e. shared secret). Meanwhile my own wireless connections are "open", and therefore unencrypted. There is no technical reason why i can't have an encrypted link that doesn't require the user to enter any password. Such technology exists today (see public key encryption and HTTPS). But does such a standard exist for WiFi? Note: i only want to protect communications, not limit internet access. i get the sense that no such standard exists (since i'm pretty capable with Google), but i'd like it confirmed. Claraification: i want to protect communcations, not limit internet access. That means users are not required to have a password (or its moral equivalent). This means users are not required: to know a password to know a passphrase to enter a CAPTCHA to draw a secret to have a key fob to know a PIN to use a pre-shared key have a pre-shared file to possess a certificate In other words: it has the same accessibility as before, but is now encrypted.

  Read the article

• Understanding !d command in sed with respect to saves

  - by richardh

  I have a directory of tab-delimited text files and some have comments in the first few lines that I would like to delete. I know that the first good line starts with "Mark" so I can use /^Mark/,$!d to delete these comments. After this deletion I have several other replacements that I make in the (new) first line that has variable names. My question is, why do I have to save sed's output to get my script to work? I understand that if I line is deleted, then the output doesn't proceed downstream because there is no output. But if I don't delete (i.e., !d) then why do I have to save to file? Thanks! Here is my shell script. (I'm a sed newbie, so any other feedback is also appreciated.) #!/bin/bash for file in *.txt; do mv $file $file.old1 sed -e '/^Mark/,$!d' $file.old1 > $file.old2 sed -e '1s/\([Ss]\)hareholder/\1hrhldr/g'\ -e '1s/\([Ii]\)mmediate/\1mmdt/g'\ -e '1s/\([Nn]\)umber/\1o/g'\ -e '1s/\([Cc]\)ompany/\1o/g'\ -e '1s/\([Ii]\)nformation/\1nfo/g'\ -e '1s/\([Pp]\)ercentage/\1ct/g'\ -e '1s/\([Dd]\)omestic/\1om/g'\ -e '1s/\([Gg]\)lobal/\1lbl/g'\ -e '1s/\([Cc]\)ountry/\1ntry/g'\ -e '1s/\([Ss]\)ource/\1rc/g'\ -e '1s/\([Oo]\)wnership/\1wnrshp/g'\ -e '1s/\([Uu]\)ltimate/\1ltmt/g'\ -e '1s/\([Ii]\)ncorporation/\1ncorp/g'\ -e '1s/\([Tt]\)otal/\1ot/g'\ -e '1s/\([Dd]\)irect/\1ir/g'\ $file.old2 > $file rm -f $file.old* done

  Read the article

• How to run Fujitsu P27T-7 LED monitor in its not native resolution and have perfect fonts rendering

  - by Ilia Rostovtsev

  My problem is completely opposite to anything I could find as I need to run my monitor in its NOT native resolution and have perfect font rendering. I recently got myself Ultra HD 2560x1440 27 inch monitor (Fujitsu P27T-7 LED) and I have an issue with this. I would call it personal but I'm afraid it's not as few people already agreed with me. I do programming and the text on UHD is way to small for comfortable usage. I changed the resolution to regular Full HD (1920x1080), it became just right but the text is looking slightly blur now, in comparison to both its natural UHD resolution and/or to my old 23 inch NEC. I am pretty frustrated and not sure what to do and how to make fonts look just as sleek as they should? I can't work in UHD resolution (my vision is 100% perfect), simply if calculated, picture size with Ultra HD (2560x1440) on 27 inch is around 30% smaller than Full HD (1920x1080) on 23 inch. In order to have same font size, if compared with Full HD 23 inch, 27 inch Ultra HD monitor must be around 32 inches in size. If I set my new monitor to regular Full HD 1920x1080, then the fonts' size are just perfect but the quality is not as it's blurry? Could anyone please help me out with an advise of how to solve this problem? Spec: nVidia 560 Ti with DVI-D port on Fedora 20. EDIT 1: Changing fonts doesn't really help as everything else doesn't look the way it should. EDIT 2: The monitor is buzzing on 2560x1440 so badly in case there are lots of lines on the screen, like file listing. If I type ls /usr/bin it makes such nasty irritating sound. When resolution goes to 1920x1080 it's a bit better. Any idea why?

  Read the article

• User authentication -- username mismatch in IIS in ASP.NET application

  - by Cory Larson

  Last week, an employee's Active Directory username was changed (or a new one was created for them). For the purposes of this example, let's assume these usernames: Old: Domain\11111 New: Domain\22222 When this user now logs in using their new username, and attempts to browse to any one of a number of ASP.NET applications using only Windows Authentication (no Anonymous enabled), the system authenticates but our next layer of database-driven permissions prevents them from being authorized. We tracked it down to a mismatch of usernames between their logon account and who IIS thinks they are. Below are the outputs of several ASP.NET variables from apps running in a Windows 2008 IIS7.5 environment: Request.ServerVariables["AUTH_TYPE"]: Negotiate Request.ServerVariables["AUTH_USER"]: Domain\11111 Request.ServerVariables["LOGON_USER"]: Domain\22222 Request.ServerVariables["REMOTE_USER"]: Domain\11111 HttpContext.Current.User.Identity.Name: Domain\11111 System.Threading.Thread.CurrentPrincipal.Identity.Name: Domain\11111 From the above, I can see that only the LOGON_USER server variable has the correct value, which is the account the user used to log on to their machine. However, we use the "AUTH_USER" variable for looking up the database permissions. In a separate testing environment (completely different server: Windows 2003, IIS6), all of the above variables show "Domain\22222". So this seems to be a server-specific issue, like the credentials are somehow getting cached either on their machine or on the server (the former seems more plausible). So the question is: how do I confirm whether it's the user's machine or the server that is botching the request? How should I go about fixing this? I looked at the following two resources and will be giving the first one a try shortly: http://www.interworks.com/blogs/jvalente/2010/02/02/removing-saved-credentials-passwords-windows-xp-windows-vista-or-windows-7 http://stackoverflow.com/questions/2325005/classic-asp-request-servervariableslogon-user-returning-wrong-username/5299080#5299080 Thanks.

  Read the article

• samba access from win98

  - by SimonSalman

  Hello, the admin installed a new file server in our institute: OpenSuse 11.1 with Samba 3.2.7-11.3.2-2154-SUSE-CODE11. They copied the smb.conf from the old machine (hosting Samba 3.0.0) to the new one. Everything works as before, but one Windows 98 machine can see but not access the file server. It prompts for user authentication, but will not accept any user-password combination. There exists a lot of discussion about the problem on the net, but none provided a clear answer to the problem. EDIT: 1. I changed Win98 registry enable plain-text passwords, and alternatively changed server's smb.conf and /etc/smbpasswd to accept encrypted passwords 2. Further I provide a profile with a user-password combination on Win98 machine similar to one of the samba users-password combinations. 3. I changed smb.conf such that the samba server is the Local Master Browser all these changes are not necessary when using the older samba server. So, I conclude that a configuration problem on the server side is likely. If you need any further information, I will post them here. Best regards, Simon

  Read the article

• Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

  - by WerkkreW

  I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

  Read the article

• Nginx map module 301 redirecting

  - by Reinier Korth

  I've rebuild my website in Ruby on Rails and now I want to 301 redirect a lot of old urls using Nginx's http://wiki.nginx.org/HttpMapModule For some reason I can't get it to work. It works fine without the rewrite ^ $new permanent; line. Does anyone see what I'm missing? This my nginx.conf: server { server_name example.com; return 301 $scheme://www.example.com$request_uri; } # 301 redirect list map $uri $new { /test123 http://www.example.com/test123; /bla http://www.example.com/bladiebla; } server { server_name www.example.com; rewrite ^ $new permanent; root example/public; location ^~ /assets/ { gzip_static on; expires max; add_header Cache-Control public; } try_files $uri/index.html $uri @unicorn; location @unicorn { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_pass http://unicorn-<%= application %>; } error_page 500 502 503 504 /500.html; client_max_body_size 4G; keepalive_timeout 10; }

  Read the article

• Sending mail results in "Sender address rejected: Domain not found"

  - by user1281413

  The setup: WHM/CPanel CentOS 5 server running Exim and Courier for mail services, and BIND for domain name services. I recently moved servers. The old server was running a HIGHLY similar configuration, and all accounts were ported via WHM. However, the server is unable to send, and sometimes receive email. Errors I am seeing (when I do get an error mail back) state: 450 4.1.8 : Sender address rejected: Domain not found Edit for clarity: this is the error response from remote mail servers. Numerous independent mail servers come back with the same error. (Email address is merely one valid example) My first instinct of course was to check the domain records. However, k-t.org appears to have a valid record (including an MX record), even after running it through domain checks on a completely different server elsewhere and online. Note that the issue appears to happen with all the domains hosted on the server, not just k-t.org I have also ensured that a PTR was created. My Googling has only lead me to people who had fairly basic DNS mistakes, but either I'm blind/dumb (possible, DNS is not my strong suite), or it's something that is a bit more archaic. I've run out of ideas, and I can't seem to find anything that could explain why servers are unable to resolve the domains. There doesn't seem to be anything missing or incorrect.

  Read the article

• Changing PATH Environment Variable for all Users. (Ubuntu)

  - by Wally Glutton

  I recently compiled Ruby Enterprise Edition (REE) on an Ubuntu 8.04 server. I would like to update my PATH to ensure this new version of Ruby (found in /opt/ruby_ee/bin) supersedes the older version in /usr/local/bin. (I still want the old version around, though.) I would like these PATH changes to affect all users and crontabs. Attempted Solution #1: The REE documentation recommends placing the REE bin folder at the beginning of the global PATH in /etc/environment. I altered the PATH in this file to read: PATH="/opt/ruby_ee/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games" This did not affect my PATH at all. Attempted Solution #2: Next I followed these instructions and updated the PATH setting in /etc/login.defs and /etc/crontab. (I did not change /etc/sudoers.) This didn't affect my PATH either, even after logging out and rebooting the server. Other information: I seem to be having the same problem described here. I'm testing using the commands "echo $PATH" and "ruby -v". My shell is bash. My .bashrc doesn't override my PATH. Yes, I have heard of the Ruby Version Manager project. ;)

  Read the article

• What to do when a device has no driver for Windows 7 but it has Vista, XP drivers

  - by Mehper C. Palavuzlar

  This has always been a bothersome matter for me. Some devices (printers, scanners, etc.) have drivers for older versions of Windows (Vista, XP, 2000, NT) but no driver for Windows 7. What are my chances to install such devices on Windows 7? Example case: I have a Sharp printer & scanner (Sharp AR-122E N) which I have used for my old Windows XP based PC. Now I want to install it on a Windows 7 x64 based PC. Windows 7 cannot load its driver. I used the original driver CD but when I run the setup.exe (which is included in AR122EN111.exe, 6713KB), it says Cannot install driver on this operating system. Supported operating systems are: Windows 2000, XP, Vista. I tried to install the driver using compatibility settings. I tried Windows Vista and Windows XP SP3, but to no avail. The setup gave the same error. I also googled for Windows 7 driver for "Sharp AR-122E N" but it only listed the original driver that I tried. The official site of Sharp does not even list the driver for this product. In the past, the compatibility setting workaround did work for some devices, but this time it failed. What else can I do to overcome this problem?

  Read the article

• Cookieless Domain redirect in WHM/cPANEL

  - by Patrick Lanfranco

  I am currently trying to get my head around in understanding how to set-up a "cookieless" domain using WHM / Cpanel - unfortunately without any success at this moment. I have a Magento store and I would like to use "cookieless domains" for my media, skin (template) and js files. Magento has a nice feature to define URL for those folders. My current setup is as follows: www.mydomain.com <- main store media.mydomain.com <- subdomain to the media folder (mydomain.com/media/) skin.mydomain.com <- subdomain to the media folder (mydomain.com/skin/) js.mydomain.com <- subdomain to the media folder (mydomain.com/js/) I think it's poinless to have them used as "cookieliess domains" since my Magento installation uses .mydomain.com as cookie domain, so what I would like to achieve is to register a new additional domain and have it point via WHM / cPanel to those specific locations. I have tried to change the A and CNAME records although without any success as they were just simply redirecting from one page to another in the browser (newdomain.com - jump to old.com). What kind of records do I have to set to have this working properly? Some advice would be highly appreciated.

  Read the article

< Previous Page | 580 581 582 583 584 585 586 587 588 589 590 591  | Next Page >