Search Results

Search found 23311 results on 933 pages for 'multiple computers'.

Page 585/933 | < Previous Page | 581 582 583 584 585 586 587 588 589 590 591 592  | Next Page >

• Setup 2003 R2 Radius server to work on vista/seven

  - by Fox

  Hi All, I'm currently trying to configure my 2003 R2 server RADIUS module to enable WIFI client to authenticate throught my Active Directory. The RADIUS server use MS-CHAP V2 as encryption method. I got several Access Point running DD-WRT, configured to use WPA2-Enterprise security that use Radius Server. Everything is setup, and almost working. When I say almost working, I mean, I can login using my AD Credential on my IPod or even on a MacBook running OS X, Windows XP also work with some little tweak in connection properties. The problem is Windows Vista or Windows Seven clients computers that are not inside domain. It doesn't work at all, it doesn't even prompt for user/password/domain. I already install the patch for IAS to make the certsrv compatible with Vista and Seven, but still doesn't work. Anyone ever encounter the same issue I have right now? I'm searching for a solution to this for several already and still not find anything. Looks like many people have the same issue too. Thanks all for you eventual answers.

  Read the article

• Ruckus wireless AP and Dell PowerConnect configuration problems

  - by DanielJay

  We are working on trying to get some Ruckus Access Points to work correctly on our network. Currently our network is as follows: VLAN 10 - Servers VLAN 11 – Computers/DHCP VLAN 12 – Voice VLAN 13 – Guest We use Dell PowerConnect 6248P switches for our switches. Port settings are as follows: ZoneDirector 1100 is plugged into this port. Should be accessing the server VLAN and then allowing all other traffic. interface ethernet 1/g2 classofservice trust ip-dscp description 'Ruckus ZoneDirector 1100' switchport mode general switchport general pvid 10 switchport general allowed vlan add 10 switchport general allowed vlan add 11-13 tagged exit Access point is plugged into this port. The port has to be on VLAN 11 in order to get DHCP. interface ethernet 1/g16 classofservice trust ip-dscp description 'Ruckus - IT' switchport mode general switchport general pvid 11 switchport general allowed vlan add 10-12 switchport general allowed vlan add 13 tagged exit If we tag the traffic from the SSID as VLAN 11 data fails. If we leave the SSID tagged as 1 the data flows correctly. Are there problems with passing tagged traffic to untagged ports? We are looking to see what we can do to get the SSID tagged as 11 instead of 1. Any suggestions?

  Read the article

• Ubuntu questions - important

  - by asdasd

  They had installed some modified edubuntu's at school... So i have some questions about setting some things up: How we can play HD videos ? They are made for windows machines and are in .wmv format but we need to play them on our multimedia class but don't know how - which player, which codecs etc. How to edit properly the /etc/apt/sources file ? Anything we try to install via apt-get it just says that E:\ is not available. Please tell me which repositories to put in there so we could be able to install some tools. Where are usually viruses/trojans put in ubuntu ? I mean in which directories ? Because our computers are behaving really slow and we need to check for some malware manually - we are not even allowed to install any kind of AV software. So tell me the usual directories and places for hiding such files, how are they hiddem, how to recognize them etc. Any others nice tricks/tips that we need to know. Thank you very much in advance.

  Read the article

• How to pipe internet radio into a tuner?

  - by JW

  UPDATE: Thanks everyone for the ideas! This was an area I knew very little about but now I can talk with a little more expertise about it. Much appreciated! Visited my dad this weekend and he wants to pipe some internet radio he's found down to a tuner on quite a distance away in the house. He uses computers for only very basic things: e-mail, getting the Post crossword, checking Yahoo!, checking recipes, etc. There's currently one computer in the house (no router). My initial suggestion (without any research whatsoever) was to get a wireless router and a netbook for downstairs near the tuner, but he initially wasn't too keen about having another computer down there. Anyway, is there any computer hardware that could magically pipe the audio output from the computer down to one set of (RCA) audio inputs on the tuner? Wireless isn't necessary but it probably would be easier. Anyway, thanks for your suggestions! UPDATE Thanks everyone! Voted up all of your suggestions now that I have 15 rep. Much appreciated.

  Read the article

• Can't log in using second domain controller when first DC is unreachable

  - by rbeier

  Hi, We're a small web development company. Our domain has two DCs: a main one (BEEHIVE, 192.168.3.20) in the datacenter and a second one (SPHERE2, 10.0.66.19) in the office. The office is connected to the datacenter via a VPN. We recently had a brief network outage in the office. During this outage, we weren't able to access the domain from our office machines. I had hoped that they would fail over to the DC in the office, but that didn't happen. So I'm trying to figure out why. I'm not an expert on Active Directory so maybe I'm missing something obvious. Both domain controllers are running a DNS server. Each office workstation is configured to use the datacenter DC as its primary DNS server, and the office DC as its secondary: DNS Servers . . . . . . . . . . . : 192.168.3.20 10.0.66.19 Both DNS servers are working, and both domain controllers are working (at least, I can connect to them both using AD Users + Computers). Here are the SRV records that point to the domain controllers (I've changed the domain name but I've left the rest alone): C:\nslookup Default Server: beehive.ourcorp.com Address: 192.168.3.20 set type=srv _ldap._tcp.ourcorp.com Server: beehive.ourcorp.com Address: 192.168.3.20 _ldap._tcp.ourcorp.com SRV service location: priority = 0 weight = 100 port = 389 svr hostname = beehive.ourcorp.com _ldap._tcp.ourcorp.com SRV service location: priority = 0 weight = 100 port = 389 svr hostname = sphere2.ourcorp.com beehive.ourcorp.com internet address = 192.168.3.20 sphere2.ourcorp.com internet address = 10.0.66.19 Does anyone have any ideas? Thanks, Richard

  Read the article

• Prevent Exchange Server from advertising itself on domain

  - by Justin Shin

  I'm in the middle of setting up an Exchange 2010 Server. Currently, we use a SaaS provider for Exchange 2007 services. Some (but not all) of my users have been reporting that they are receiving Outlook/Exchange login prompts to login to the new Exchange server. This is happening without any intervention on the client's machines. The Exchange server is a member of the domain and connects to the domain site remotely through a site-to-site VPN. What can I do to prevent these login prompts from appearing? Will shutting down the new server until it is time to switch resolve these issues? A little more info: I found that on one of the client computers, all of the settings for Outlook over HTTP had been changed (automatically) from webmail.provider.com to mail.company.com (the latter being the new server). This happened when I enabled Outlook Anywhere access on Exchange 2010. I changed the client's settings back, and everything was groovy. But, when I disabled Outlook Anywhere again, the logon prompt came back.

  Read the article

• Windows 7 x64 RTM USB Port Has Power But Won't Recognize Mouse/Keyboard/Anything

  - by ben

  I have an odd error that doesn't seem to fit in with any of the other odd Windows 7 x64 USB errors that have been kicked up on Google. Here we go: Uninstalled Tortoise SVN and clicked restart computer. My machine had been up for around 28 days On reboot my mouse and keyboard failed to work anymore, couldn't log in. Tried every USB port I have on my Dell 390 and the ports on my Dell 19's, nothing worked. They had power but Windows would not respond when I manipulated the keyboard/mouse. Rebooted my computer and pressed F2 to get into bios, my keyboard is working fine in bios. Keyboard and mouse work fine on other computers when using USB. Found adapters for keyboard and mouse to convert from USB to PS/2 ports, works fine. I'm actually typing this question on the same keyboard, same computer, just using PS/2 ports for my mouse and keyboard. It appears to be a Windows 7 x64 issue. Other things I have tried: Multiple other mice and keyboards, iphone, all with no luck. Each one gets power, but Windows never tries to install drivers or sees that they are connected. Uninstall and reinstall all USB drivers. Drives uninstall and reinstall fine and report no errors in Control Panel. In Power Management I disallow Windows from turning off USB ports to save power Installed the latest nVidia drivers for my graphics card, no change. Anyplace else I can look/try? Thanks!

  Read the article

• Self-Resetting Power Strips?

  - by Justin Scott

  We are about to deploy a number of secure kiosks into an environment where they may be prone to lightning strikes and power surges on a somewhat regular basis (southern Florida in a place where the existing electrical infrastructure is, shall we say, a bit out of date). Ideally we would use battery backups on each system, but it's not in the budget. We plan to use a standard power strip with a circuit breaker built-in to protect the computers, but management has asked if there is a power strip that can reset itself after the breaker has been tripped. I've looked around and wasn't able to find such a beast, and it seems to me that it would probably be a safety issue for such a product to exist (e.g. if something plugged into the strip is drawing a lot of current and trips the breaker, you wouldn't want that resetting itself to prevent a possible fire). Nevertheless, if anyone has experience with such a product or can point me in the direction of something that would allow the breakers to be reset automatically or remotely (we don't want to have to send someone to each kiosk every time there is a power surge) I would appreciate any tips.

  Read the article

• Different approaches to share files over local network & playlists "collaboration"

  - by exTyn

  I know, that I can use Google to find methods to share files over local network [1]. But, I have never shared files over local network, and I want to do this in a good, professional way. Also, this could be a good community wiki, I think. Well, what I am asking for, is: what are pros and cons of different methods to sharing files ofver local network? In my case, I need to share files between Linux & Win 7, and I want it to be secure (= without access for anyone else but me & people in my room). Another question (connected with above topic) is about playing music over the local network. Let's say, I live with 2 other guys in a room, one of us have speakers and we want to collaborate in creating playlists (e.g. everyone is choosing 3 songs to be played). Is it possible? How to do this? I am asking this question on SuperUser, because it (question) is connected with hardware & software (network, connecting computers, software for managing playlists in network etc.). I think it is most accurate place for such question (I have considered SO and SF). [1] And I have already done this! But, I do not have an experience in this field (sharing files over local network), do I am asking about pros and cons.

  Read the article

• NetInstall working on some systems, not working on others

  - by cduruk

  Hi, I'm having an issue where my NetInstall setup works on some computers and fails on others. I am not able to diagnose the issue. I created an image of a Mac Mini and then created a NetRestore image using the System Image Utility found on Snow Leopard Server. NetBoot and NFS all seem to be working fine on the server, which is an XServe. Then I select the NetInstall image from the Startup Disk on a machine. On some of the machines, the process works as expected. On some of them, I see the globe icon blink a few times and then the system boots to the regular hard drive. I have captured the tracedump and the system.log logs from the server on both cases where NetInstall seems to work and fail. Here is the link that has all the logs http://gist.github.com/232232 The gist of the failure seems to be from the lack of BSDP DISCOVER in the failure but I'm not able to identify why that exactly is happening. I'd really appreciate any help on this issue.

  Read the article

• Automate creation of Windows startup script?

  - by Niten

  Is there a good way to automate installing local startup (rather than login) scripts in Windows XP and Windows 7, via the command line, WMI, or otherwise (even COM or Win32 if it comes to that)? I need to setup a local startup script on a large number of computers, and unfortunately, Active Directory is absolutely not an option. I would like to write a script or small program that I can run on each computer to perform the startup script installation in order to save myself a lot of error-prone point-and-click manual labor. I see that when one uses gpedit.msc to create a local startup script, information about the script gets stored in the registry here: HKLM\Software\Policies\Microsoft\Windows\System\Scripts\Startup However, if you create such a script and then delete its registry key, the script will remain listed in the local Group Policy editor; as is so often the case in Windows, apparently there is more going on there than meets the eye. This leads me to question whether it's safe to manually add subkeys for new startup scripts here (I wouldn't want my script to be overwritten by later changes made using the local Group Policy editor, for instance)... Another option that's occurred to me is to create an item in the Task Scheduler configured to run at system startup. However, my concerns there are twofold: Can this be automated any more easily? For instance, the at command doesn't appear to let you schedule a task for system startup, and WMI's Win32_ScheduledJob interface looks unreliable (it fails to show any of my currently scheduled tasks, for one thing). Would I be able to prevent users from logging in until the scheduled startup task is completed, as can be done with "normal" Windows startup scripts? Thanks in advance for any suggestions, I've been banging my head against this one for a bit...

  Read the article

• Different approaches to share files over local network

  - by exTyn

  I know, that I can use Google to find methods to share files over local network [1]. But, I have never shared files over local network, and I want to do this in a good, professional way. Also, this could be a good community wiki, I think. Well, what I am asking for, is: what are pros and cons of different methods to sharing files ofver local network? In my case, I need to share files between Linux & Win 7, and I want it to be secure (= without access for anyone else but me & people in my room). Another question (connected with above topic) is about playing music over the local network. Let's say, I live with 2 other guys in a room, one of us have speakers and we want to collaborate in creating playlists (e.g. everyone is choosing 3 songs to be played). Is it possible? How to do this? I am asking this question on SuperUser, because it (question) is connected with hardware & software (network, connecting computers, software for managing playlists in network etc.). I think it is most accurate place for such question (I have considered SO and SF). [1] And I have already done this! But, I do not have an experience in this field (sharing files over local network), do I am asking about pros and cons.

  Read the article

• Private staff network within public network

  - by pianohacker

  I'm the sysadmin at a small public library. Since I got here a few years ago, I've been trying to set up the network in a secure and simple way. Security is a little tricky; the staff and patron networks need to be separated, for security reasons. Even if I further isolated the public wireless, I'd still rather not trust the security of our public computers. However, the two networks also need to communicate; even if I set up enough VMs so they didn't share any servers, they need to use the same two printers at the very least. Currently, I'm solving this with some jerry-rigged commodity equipment. The patron network, linked together by switches, has a Windows server connected to it for DNS and DHCP and a DSL modem for a gateway. Also on the patron network is the WAN side of a Linksys router. This router is the "top" of the staff network, and has the same Windows server connected on a different port, providing DNS and DHCP, and another, faster DSL modem (separate connections are very useful, especially as we heavily depend on some cloud-hosted software). tl;dr: We have a public network, and a NATed staff network within it. My question is; is this really the best way to do this? The right equipment would likely make my job easier, but anything with more than four ports and even rudimentary management quickly becomes a heavy hit on our budget. (My original question was about an ungodly frustrating DHCP routing issue, but I thought I'd ask whether my network was broken rather than asking about the DHCP problem and being told my network was broken.)

  Read the article

• What parts of a motherboard age, and how can I choose one with the longest possible life?

  - by Robert Harvey

  I have a home-built computer that's probably about four years old. I realize this probably seems ancient to some folks, but computers have no moving parts (except the fans), so theoretically they should last a long time, if I still have software to run on them. A few weeks ago, it began blue-screening and freezing up, with various error messages. It almost always happened about five minutes after startup. I assumed that the video card was overheating, since the cheap little fan on the heatsink died, so I replaced it. Long story short, after upgrading the video drivers a couple of times and performing some other troubleshooting, I remembered that the last time this happened, I took out the memory SIMS and cleaned the contacts with a gum eraser, so I did that again (noting that the SATA cables were very close to the chips on the SIMS). I re-routed the cables and reinstalled the SIMS. So far, so good; the machine has been trouble-free since. But blue-screens are distressing; I never know what bits are being chewed up in my OS installation when something like this happens. So I'm wondering if I'm choosing my components properly. If it matters, it's an Intel D915GAG motherboard and Corsair memory, but what I'm wondering is, should I be looking for certain characteristics when I choose these parts for my next computer, so that I can avoid this problem in my next build?

  Read the article

• Being a more attractive job candidate - Certs XOR Degree

  - by Zephyr Pellerin

  I'm currently working in an IT position, where I do helpdesk stuff, and predominantly security related issues/consulting (In the loosest sense of the term) In-House and for Service-Contract clients (as the only/acting CCSP [I guess I should say only person with Cisco experience] in my organization). I've professionally written Kernel Mode drivers for a gaming company. Among other things that I'm proud to put on a resume. I think of myself as very reasonably qualified as a System Administrator, With excellent Cisco experience, among other things I think would make a good addition to almost any IT staff in need of a new employee. However, Something has always tripped me up - Human Resources. Let me explain, I decided to skip the university route - I'm immensely glad that I did, The computer science graduates that I've met and work with rarely know much of anything about Computers (Until they gain some 'real' experience), Even when asked about Theoretical Computing fundamentals they can rattle something off about Turing Completeness but rarely do they understand the mathematical underpinnings. In short, I think instead of going to college, I'd rather pick up some real world experience. However, Apparently, Employers rarely think the same way. A quick perusal of jobs through the standard job search engine yields nothing short of a conspiracy to exclude anyone without 'A Bachelors Degree in Computer Science or Equivalent'. Interviews I've had in the past have almost always been entangled with - 1. My Age (Which I can't really change) and 2. Lack of Degree. Employers frequently disregard the CCNA/CCSP, The experience I've gained through internships, My extensive experience in x86 assembly and C, among so many other things I like to think are valuable to employers - In lieu of the fact that I don't have a piece of paper. So, AS AN EMPLOYER - Is it even worth working on my CCIE? Or should I pad my resume with certifications that are easier to acquire (Like CISSP, MSCE, Network+, etc.). Or should I ditch the whole idea and head back to get a Mathematics or CS degree?

  Read the article

• Interactive console based CSV editor

  - by Penguin Nurse

  Although spreadsheet applications for editing CSV files on the console used to be one of the earliest killer applications for personal computers, only few of them and even less documentation about them is still actively maintained. After having done extensive search on the web, manpages and source code, I ended up with the following three applications that all have fundamental drawbacks: sc: abbrev. for spreadsheet calculator; nice tool with vi keybings, but it does not put strings containing the delimiter into quotas when exporting to delimiter separated format and can't import csv files correctly, i.e. all numbers are interpreted as strings GNU oleo: doesn't seem to be actively maintained any longer since 2001 and there are therefore no packages for major linux distributions teapot: offers packages for various operating systems, but uses for example counter-intuitive naming for cells (numbers for row and column, i.e. 11 seems to be intended to be row 1, column 1) and superfluous code for FLTK GUI Various Emacs modes also do not quote strings containing the delimiter well or are require much more typing for entering the scaffold of a table. Therefore I would be very grateful for overcoming one of theses drawbacks or any hints towards another console based CSV editor. It actually needn't do any calculations just editing cells or column- and rowise.

  Read the article

• Wireless to Wireless Transfer Slow on a Linksys WRT54GL

  - by Kyle Brandt

  The Situation: When I try to transfer a file from one computer to another that are both connected via wireless on a WRT54GL (in a office) with dd-wrt firmware I often get bad speeds. In generally they average around 100 kilobytes a second. Either computer can download via wireless from the Internet at at about 2 megabytes a second. The speed is slow with the transfer of one large file. There are about 20 other wireless networks that the computers can see, so there is a lot of noise, but I don't have the equipment to really monitor the frequencies well. But that still seems pretty slow. I thought maybe it was the transmit on each card, but even when they are 5 feet away with a line of sight I still get these speeds. According to Linux both cards are operating at 54g. My Questions: Is this normal for this sort of consumer level wireless equipment? Anything I can do to improve it? why is wireless to wireless transfer slow when everything else isn't? Whats steps might I take to figure out what is happening? For example, are lots of packets not making to the access point requiring retransmissions? Above all, I want to find out what the problem actually is. This may seem odd, but at this point I am more interested in understanding what the problem is than fixing it. What I have tried: I have tried messing with lots of settings. Different channels, xmit power, G-Only, none of which has made anything any better. I've also tried upgrading to newer dd-wrt firmware version and doing a reset to wipe out the settings.

  Read the article

• router only assigns small number of IPs

  - by Liam Coates

  Been having a problem with my router for a while now, might just be because it is really old but here's the problem: If a lot of computers are connected to my home network someone will get disconnected. They are assigned IPs and it seems like at a certain point (and I don't know how many) you either get assigned the same IP as someone else or something else is happening and you get disconnected - until i soft reset it and it works again which takes 30 secs. I'd say my tablet, my PC, my sisters iPad, 2 laptops and a netbook is the most that can be connected at one time so that is 6 but that should be fine. The only way I know this is the problem is because I turned on my tablet and I was online on my PC, got disconnected but my tablet was still connected, this is just after i turned the tablet on so I know my router is having difficulty with IPs, it is like it assigned the same IP to the tablet which then clashed with my desktop and knocked me off. I see that sometimes the following solves it as well so I wrote a batch file with a menu to execute these commands as I have to do it so often. ipconfig /release ipconfig /flushdns ipconfig /renew Any ideas? Or shall I just get a new router as this one is old and maybe can't handle giving out that many IPs? Cheers!

  Read the article

• Port forwarding + shared connection with Ubuntu

  - by Joey Adams

  Because my wireless router's ethernet ports are defective, I set up a shared wireless connection from my laptop (which has wifi) to my eMac (which does not) via a crossover ethernet cable. The laptop is behind a router as 192.168.1.131, and the eMac is behind the laptop as 10.42.43.1 . The laptop is running Ubuntu 9.10 (Karmic). I achieved the shared connection through NetworkManager Applet. I right-clicked on the network icon at the topright, went to Edit Connections, selected the Wired connection named "Auto eth0", clicked "Edit...", went to the "IPv4 Settings" tab, and selected the Method "Shared to other computers". The eMac can now access the Internet. Now I want to enable port forwarding. There's a game I want to play that needs port 6112 forwarded (both TCP and UDP) in order to host games. I set up the router to enable port forwarding for 192.168.1.131 (the laptop), but port forwarding still isn't available on the eMac. I suppose I need to pretend my laptop is a router and configure port forwarding on it, indicating that incoming connections to the laptop (192.168.1.131) should be forwarded to the eMac on the shared connection (10.42.43.1 ). Thus, packets coming into the router on port 6112 would be redirected to the laptop (by the router), then to the eMac (by the laptop). My question is, how would I do that on Ubuntu (in light of NetworkManager's presence)? Also, if I can't get this to work, does anyone mind hosting a comp stomp? :D

  Read the article

• Home network with two isolated separate subnets, running on cablemodem/router and WRT-router.

  - by Johan Allgoth

  I have a new connection with a nice new router/cable-modem. I'd like to setup it up optimally and needs some pointers. I am a complete n00b when it comes to routing. I want to end up with two separate subnets, 10.1.2.0/24 and 192.168.1.0/24 each available on their own wireless channel/SSID. Both firewalled. I want my wired computers on the gigabit switch, optimally with public ips. I want to be able to reach 192.168.1.0/24 from 10.1.2.0/24, but not vice versa. Everyone should have internet access. Hardware and capabilities: Netgear CG3100. Handles cable connection. Gigabit switch. 802.11n. Can do DHCP, firewall, NAT etc. Can choose subnet. Can turn of NAT and if so hand out up to 4 public ips. Somewhat challenged when it comes to configuration. WRT-router. Runs DD/Open-WRT very stable. 100 Mbit switch. 802.11.g Can do DHCP, firewall, NAT etc. Can choose subnet. Highly configurable. I hope to be able to keep 10.1.2.0/24 on the CG3100, for speed reasons and 192.168.0.0/24 on the WRT-router for quota and user control reasons. On my 10.1.2.0/24 network I plan on running servers for various services. Should I turn of NAT on the WRT-router? Or on the cable modem? Activate what in that case? Is double NAT always f-ed up?

  Read the article

• Cannot find network path for computer in workgroup of home Windows XP PCs

  - by John Galt

  VMWare Workstation 6.5 is running as an app on a Windows Vista 64bit PC host. Thanks to Workstation we have 2 guest machines running: TerriVM and MattVM (both of these run Windows XP SP2). We are attempting to get virtual networking configured so we can access the files of both of these VM guest systems from other real PCs connected to this home network. We think we are close but we can't quite get it right... Here is what we've done so far: * On VM Workstation, we set "Host Virtual Network Mapping" to use VMnet0 with the setting "Bridge to an automatically chosen adapter". * On each VM guest (i.e. using Windows explorer on XP), we rightmouse on the C disk, click "Sharing" tab, set shareName to "C_Disk" and check both boxes labeled "Share this folder on the network" and "Allow network users to change my files". Symptoms: On "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \TerriVM\C_Disk and assign drive letter T. We see all the folders on this shared drive and can open files on them. So that is good. On same "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \MattVM\C_Disk and assign drive letter M. We get a message box "_The network path \mattvm\C_Disk could not be found_". Alternatively, we type just \mattvm\ into the Folder box and click "Browse" and get a dialog box where we drill down from "Entire Network" to "Microsoft Windows Network" to "Workgroup" where both TerriVM and MattVM are listed as computers on the network. Clicking the + sign next to MattVM gives an hourglass and never enables the OK button and I have to cancel. In summary, I think we've attempted to share both of these virtual machines using the same techniques and connect to them in similar fashion, but one connects properly and the other machine can be seen but no shared resources on it can be accessed. Can anyone suggest something possibly overlooked or something to try? Thanks so much in advance.

  Read the article

• Shorewall log question.

  - by Shikoru

  I have been getting various attempts to connect to ports on my shorewall firewall. The ports that I keep seeing connection attempts at are tcp 44444, tcp 44446, udp 55555 and every now and then some slight variation. I ran "netstat -a" and did not see anything listening on those ports. Is this something that I should be worried about or is it just some rouge computers out there? I have noticed alot of the ip addresses are from Spain and Mexico. May 25 18:39:35 Takkun kernel: [62516.626514] Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:d0:b7:65:d4:13:34:ef:xx:xx:xx:81:08:00 SRC=200.124.9.113 DST=72.xxx.xxx.xxx LEN=48 TOS=0x00 PREC=0x00 TTL=112 ID=51796 DF PROTO=TCP SPT=2071 DPT=44446 WINDOW=16384 RES=0x00 SYN URGP=0 May 25 18:39:52 Takkun kernel: [62535.433285] Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:d0:b7:65:d4:13:34:ef:xx:xx:xx:81:08:00 SRC=72.50.95.174 DST=72.xxx.xxx.xxx LEN=90 TOS=0x00 PREC=0x00 TTL=105 ID=31130 PROTO=UDP SPT=59505 DPT=55555 LEN=70 May 25 18:40:05 Takkun kernel: [62548.963413] Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:d0:b7:65:d4:13:34:ef:xx:xx:xx:81:08:00 SRC=77.12.37.1 DST=72.xxx.xxx.xxx LEN=90 TOS=0x00 PREC=0x00 TTL=108 ID=9585 PROTO=UDP SPT=20401 DPT=55555 LEN=70 That is the jist of what im seeing.

  Read the article

• Why does Windows make random "device connect" and "device disconnect" sounds?

  - by Steve Elmer

  Hello, I've been noticing this since Windows Vista. I see it on Windows 7, now, as well. In any case throughout the day I notice that my computer makes apparently random device-connect and/or device-disconnect ("boink") sounds. I suppose it is the same sound you hear when connecting or disconnecting a USB device such as a thumb drive. I've noticed that this happens on each of three computers I work with at home, my wife's computer, and my machine at work. It happens without any user action at all - i.e. I'll be just sitting there (hands off my mouse and keyboard), and the computer will make the sound. There is no visual queue or anything. Just the sound. I have sometimes gone in pursuit of the sound - running virus scans, examining event logs and such, and observing task manager - but have never had any luck tracking this thing down, but have not had any luck. Surely someone else out there must be experiencing this, too. Any ideas? Thanks, Steve

  Read the article

• Software way to cool down an old MacBook Pro

  - by notMacBookProSuperUser

  Hi all, First a little background: I've got lots of computers, including Linux PCs and two MacBook Pro (and a MacMini). My concern is with my 'old' MacBookPro (Core Duo). It really does overheat. Warranty is long void. Years ago (I'd say 2.5 years ago or so) one day it overheated so bad that the battery inflated due to the heat. I got a new battery for free but it's still getting incredibly hot (much other than any other computer I've got: my newer Core 2 Duo MacBook Pro doesn't get nearly as hot as the old one. It s really a pain because I use my old MBP when I m in front of TV, having it on my lap, and it can really become unbearable. I don't want to open that old MBP. On Linux I can force a new CPU 'governor' that decides how the CPU is allowed to operate: it can be 'on demand', 'always max speed', 'always speed x', etc. Does the same exist under MacOS X? Is there a way, say if a 1.86 Ghz Core Duo can run at 1.6 Ghz, to ask MacOS X: "never run this CPU above 1.6 Ghz" ?

  Read the article

• Why does Windows make random "device connect" and "device disconnect" sounds?

  - by Steve Elmer

  Hello, I've been noticing this since Windows Vista. I see it on Windows 7, now, as well. In any case throughout the day I notice that my computer makes apparently random device-connect and/or device-disconnect ("boink") sounds. I suppose it is the same sound you hear when connecting or disconnecting a USB device such as a thumb drive. I've noticed that this happens on each of three computers I work with at home, my wife's computer, and my machine at work. It happens without any user action at all - i.e. I'll be just sitting there (hands off my mouse and keyboard), and the computer will make the sound. There is no visual queue or anything. Just the sound. I have sometimes gone in pursuit of the sound - running virus scans, examining event logs and such, and observing task manager - but have never had any luck tracking this thing down, but have not had any luck. Surely someone else out there must be experiencing this, too. Any ideas? Thanks, Steve

  Read the article

< Previous Page | 581 582 583 584 585 586 587 588 589 590 591 592  | Next Page >