Search Results

Search found 17860 results on 715 pages for 'virtual pc'.

Page 587/715 | < Previous Page | 583 584 585 586 587 588 589 590 591 592 593 594  | Next Page >

• QoS for Cisco Router to Prioritize Voice and Interactive Traffic

  - by TJ Huffington

  I have a Cisco 891W NATing Voice and Data to the internet over a 10mbit/2mbit connection. Voice traffic gets degraded when I upload large files. Pings time out as well. I tried to configure a QoS policy but it's basically not doing anything. Voice traffic still degrades when upload bandwidth gets saturated. Here is my current configruation: class-map match-any QoS-Transactional match protocol ssh match protocol xwindows class-map match-any QoS-Voice match protocol rtp audio class-map match-any QoS-Bulk match protocol secure-nntp match protocol smtp match protocol tftp match protocol ftp class-map match-any QoS-Management match protocol snmp match protocol dns match protocol secure-imap class-map match-any QoS-Inter-Video match protocol rtp video class-map match-any QoS-Voice-Control match access-group name Voice-Control policy-map QoS-Priority-Output class QoS-Voice priority percent 25 set dscp ef class QoS-Inter-Video bandwidth remaining percent 10 set dscp af41 class QoS-Transactional bandwidth remaining percent 25 random-detect dscp-based set dscp af21 class QoS-Bulk bandwidth remaining percent 5 random-detect dscp-based set dscp af11 class QoS-Management bandwidth remaining percent 1 set dscp cs2 class QoS-Voice-Control priority percent 5 set dscp ef class class-default fair-queue interface FastEthernet8 bandwidth 1024 bandwidth receive 20480 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto auto discovery qos crypto map mymap max-reserved-bandwidth 80 service-policy output QoS-Priority-Output crypto map mymap 10 ipsec-isakmp set peer 1.2.3.4 default set transform-set ESP-3DES-SHA match address 110 qos pre-classify ! fa8 is my connection to the internet. Voice traffic goes over a VPN ("mymap") to the SIP server. That's why I specified "qos pre-classify" which I believe is the way to classify traffic over the VPN. However even when I ping a public IP while saturating upload bandwidth, the latency is exceptionally high. Is this configuration correct? Are there any suggestions that might make this work for my setup? Thanks in advance.

  Read the article

• Connection speed drops from 1 Gbps to 10 Mbps (Vista 64)

  - by Kevin Hakanson

  I recently got a Windows Home Server (HP MediaSmart Server EX490) setup so I could do backups and other things. However, I am having trouble on my Vista 64 PC. The backup will be making great progress, then it will just slow down. At one point, I noticed the lights on my Netgear GS105 indicated it was not using a 1000 Mbps connection, but a 10 Mbps one. I checked the Status of Local Area Connection (Intel(R) 82567V-2 Gigabit Network Connection) and that also showed the same slow speed. This has happened several times in the last couple days. When I disabled the network device, and then enabled it, it established the 1 Gpbs connection again. However, some of the times the Sent Bytes Activity on the Status windows indicate that the data flow is still slow (100 to 1000 bytes every couple seconds). Obviously, at this rate I could backup faster to floppy disk. :) My question is how to diagnose and fix this problem. When I look at the Administrative Events, I do a Errors: Bonjour Service 456: ERROR: read_msg errno 10054 (An existing connection was forcibly closed by the remote host.) And a Warning: e1yexpress Intel(R) 82567V-2 Gigabit Network Connection Link has been disconnected. I am suspicious there is some power saving mode. I found a post suggesting System Idle Power Saver(SIPS) may be the issue. I am going to try that, but looking for other suggestions or diagnostic advice. I have several new items in this configuration: server, client software, switch and cat6 cables.

  Read the article

• I am getting a SQUID Error

  - by Dave

  Hello, What exactly is wrong here Entry in SQUID File--- httpd_accel_host virtual httpd_accel_port 80 httpd_accel_with_proxy on httpd_accel_uses_host_header on acl lan src 192.168.1.1 192.168.2.0/24 http_access allow localhost Error after: service squid restart 2010/02/01 14:24:29| Processing Configuration File: /etc/squid/squid.conf (depth 0) 2010/02/01 14:24:29| cache_cf.cc(361) parseOneConfigFile: squid.conf:10 unrecognized: 'broken_vary_encoding' 2010/02/01 14:24:29| WARNING: Netmasks are deprecated. Please use CIDR masks instead. 2010/02/01 14:24:29| WARNING: IPv4 netmasks are particularly nasty when used to compare IPv6 to IPv4 ranges. 2010/02/01 14:24:29| WARNING: For now we assume you meant to write /0 2010/02/01 14:24:29| WARNING: (B) '::/4294967200' is a subnetwork of (A) '::' 2010/02/01 14:24:29| WARNING: because of this '::' is ignored to keep splay tree searching predictable 2010/02/01 14:24:29| WARNING: You should probably remove '::/4294967200' from the ACL named 'all' 2010/02/01 14:24:29| WARNING: Netmasks are deprecated. Please use CIDR masks instead. 2010/02/01 14:24:29| WARNING: IPv4 netmasks are particularly nasty when used to compare IPv6 to IPv4 ranges. 2010/02/01 14:24:29| WARNING: For now we assume you meant to write /128 2010/02/01 14:24:29| aclParseIpData: unknown netmask '255.255.255.255' in '127.0.0.1/255.255.255.255' FATAL: Bungled squid.conf line 25: acl localhost src 127.0.0.1/255.255.255.255 Squid Cache (Version 3.1.0.14): Terminated abnormally. CPU Usage: 0.013 seconds = 0.006 user + 0.007 sys Maximum Resident Size: 0 KB Page faults with physical i/o: 0 Also please provide me with the simplest squid script for the proxy to run. Restrictions can be entered. Thanks Dave

  Read the article

• No VMKernel Dump File on PSOD for ESXi 4

  - by user66481

  On PSOD no VMKernel Dump File is written to disk and no message is written to screen (the screen is either blank or full of dashes). I need this data to understand why the system crashes; any help as to how to fix this to write a dump file would be appreciated. Thanks. Notes: VMKCore partition exists, is active, and is configured (esxcfg-dumppart -l). esxcfg-advcfg -g /Misc/PsodOnCosPanic = 1. esxcfg-advcfg -g /Misc/CosCoreFile = /var/core. esxcfg-dumppart -C -D /vmfs/devices/disks/ = "Error running command. Unable to copy the dump partition: Couldn't find a valid VMKernel dump file. Dump partition might be uninitialized." Hardware diagnostics (Dell) checks okay. Hardware: VMWare ESXi 4.1.0 (VMKernel Release Build 320137) Dell Inc. Optiplex 960 (2 Drives) Intel Core 2 Quad CPU Q9400 2.66GHz Configuration: 2 Virtual Machines: Windows Server 2003 R2 Enterprise Edition SP2 (1 on each drive) VM 1: Executes Batch Jobs (Has Internet Information Services 6) VM 2: Database Server (Has SQL Server 2000)

  Read the article

• ssh tunnel - bind: Cannot assign requested address

  - by JosephK

  Trying to create a socks (-D) ssh tunnel - Linux box to Linux box (both centos): sshd running on remote side ok. From local machine we do / see this: ssh -D 1080 [email protected]. [email protected]'s password: bind: Cannot assign requested address (where 8.8.8.8 is really my server's IP and 'user' is my real username) I am logged into the remote side in this terminal-window. I can verify that the local port was unused prior to this command, and then used by an ssh process, after the command, via: netstat -lnp | grep 1080 So, unlike most googled-responses with this error, the problem would not seem to be the loopback interface assignment. If I try to use this tunnel with a mail client, the local-side permits the attempt (no 'proxy-failed' error), but no data / reply is returned. On the remote side, I do have "PermitTunnel yes" in my sshd_config (though 'yes' should be the default, anyway). Ideas or Clues? Here is the relevant debug-output OpenSSH_5.3p1, OpenSSL 1.0.0-fips 29 Mar 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * .... debug1: Authentication succeeded (password). debug1: Local connections to LOCALHOST:1080 forwarded to remote address socks:0 debug1: Local forwarding listening on 127.0.0.1 port 1080. debug1: channel 0: new [port listener] debug1: Local forwarding listening on ::1 port 1080. bind: Cannot assign requested address debug1: channel 1: new [client-session] debug1: Entering interactive session. debug1: Sending environment. debug1: Sending env LANG = en_US.utf8 Other clue: If I run a Virtual Box on the client running Windows, open a tunnel with putty in that box, that tunnel, to the same remote server, works.

  Read the article

• nginx reload failing: `object version does not match bootstrap parameter`

  - by Jean Jordaan

  I added a server stanza to my virtual.conf, and now nginx seems to have a problem reloading the config. At this point I don't know what exactly is going wrong or how to debug better. Any help would be most appreciated. The config test succeeds: root@server:~# service nginx configtest nginx: the configuration file /etc/nginx/nginx.conf syntax is ok nginx: configuration file /etc/nginx/nginx.conf test is successful I'm tailing the logfile. Upon reload, the following error is logged. As far as I can see, the new config is not used. root@server:~# service nginx reload Reloading nginx: [ OK ] root@server:~# ==> /var/log/nginx/error.log <== nginx object version 0.8.54 does not match bootstrap parameter 1.0.15 at /usr/lib64/perl5/XSLoader.pm line 94. Compilation failed in require. BEGIN failed--compilation aborted. 2012/10/18 12:31:07 [alert] 9620#0: perl_parse() failed: 2 This is the version of nginx I'm running: root@server:~# yum info nginx Loaded plugins: fastestmirror, presto Loading mirror speeds from cached hostfile * base: ftp.udc.es * epel: mirror.nl.leaseweb.net * extras: ftp.udc.es * updates: ftp.cica.es Installed Packages Name : nginx Arch : x86_64 Version : 1.0.15 Release : 2.el6 [...] Server OS: CentOS release 6.3 (Final)

  Read the article

• Cannot connect to a VPN server - authentication failed with error code 691

  - by stacker

  When trying to connect to a VPN server, I get the 691 error code on the client, which say: Error Description: 691: The remote connection was denied because the user name and password combination you provided is not recognized, or the selected authentication protocol is not permitted on the remote access server. I validated that the username and password are correct. I also installed a certification to use with the IKEv2 security type. I also validated that the VPN server support security method. But I cannot login. In the server log I get this log: Network Policy Server denied access to a user. The user DomainName\UserName connected from IP address but failed an authentication attempt due to the following reason: The remote connection was denied because the user name and password combination you provided is not recognized, or the selected authentication protocol is not permitted on the remote access server. Any idea of what can I do? Thanks in advance! Log Name: Security Source: Microsoft-Windows-Security-Auditing Date: 12/29/2010 7:12:20 AM Event ID: 6273 Task Category: Network Policy Server Level: Information Keywords: Audit Failure User: N/A Computer: VPN.domain.com Description: Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information. User: Security ID: domain\Administrator Account Name: domain\Administrator Account Domain: domani Fully Qualified Account Name: domain.com/Users/Administrator Client Machine: Security ID: NULL SID Account Name: - Fully Qualified Account Name: - OS-Version: - Called Station Identifier: 192.168.147.171 Calling Station Identifier: 192.168.147.191 NAS: NAS IPv4 Address: - NAS IPv6 Address: - NAS Identifier: VPN NAS Port-Type: Virtual NAS Port: 0 RADIUS Client: Client Friendly Name: VPN Client IP Address: - Authentication Details: Connection Request Policy Name: Microsoft Routing and Remote Access Service Policy Network Policy Name: All Authentication Provider: Windows Authentication Server: VPN.domain.home Authentication Type: EAP EAP Type: Microsoft: Secured password (EAP-MSCHAP v2) Account Session Identifier: 313933 Logging Results: Accounting information was written to the local log file. Reason Code: 16 Reason: Authentication failed due to a user credentials mismatch. Either the user name provided does not map to an existing user account or the password was incorrect.

  Read the article

• .htaccess Permission denied. Unable to check htaccess file

  - by Josh

  I have a strange problem when adding a sub-domain to our virtual server. I have done similar sub-domains before and they have worked fine. When I try to access the sub-domain I get an 403 Forbidden error. I checked the error logs and have the following error: pcfg_openfile: unable to check htaccess file, ensure it is readable I've searched Google and could only find solutions regarding file and folder permissions, that I have checked and the solution isn't solved. I also saw problems with Frontpage Extensions, but that's not installed on the server. Edit Forgot to say that there isn't a .htaccess file in the directory of the sub-domain Edit #2 Still not been able to find a solution on this. Only things I have been able to find out is: It doesn't seem to be a problem with any .htaccess files (I've tried creating blank ones, with correct user privileges). It doesn't seem to be a problem with any folder permissions as they are all set correct. There isn't a problem with the way the sub-domain has been set up, as I've tried pointing the DocumentRoot to another folder and it worked fine. I've also done sub-domains fine before with no problem. Edit #3 Find out more information. I don't think it can be a file permission problem now, because if I access it by going to the server ip and then the directory where the site is hosted it all works fine (minus the stylesheets & images, which is just down to how they are linked)

  Read the article

• Stop Outgoing Spam Already Tagged as Spam

  - by me

  Hi, I run a Postfix server with Amavis and Spamassassin among other things. Postfix receives mail from the outside world and passes it on to Amavis. Amavis has Spamassassin rate the mail, and then tags it as spam if necessary. Then Postfix relies on each users' procmailrcs to deal with the mail as they will. I believe this is the correct approach because I believe each user should have the ability to choose what to do with their spam. Unfortunately, we also have some users with foregin domains in our virtual alises list. Because these addresses don't have user accounts with our servers, the spam that is forwarded to them is never put through a procmailrc and we end up forwarding spam, already tagged as spam, to other servers. Is there a way to stop outgoing mail already tagged as spam? Or is there any other way to fix this? EDIT: I only wish to delete the messages that are both spam AND being forwarded to other servers. I don't want to delete all mails marked as spam. Is there a way to distinguish between the two?

  Read the article

• How can I solve the apache2 httpd error "mixing * ports and non-* ports with a NameVirtualHost addre

  - by rrc7cz

  Here is the error I get when booting up Apache2: * Starting web server apache2 apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [Wed Oct 21 16:37:26 2009] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results [Wed Oct 21 16:37:26 2009] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results [Wed Oct 21 16:37:26 2009] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results [Wed Oct 21 16:37:26 2009] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results [Wed Oct 21 16:37:26 2009] [warn] NameVirtualHost *:80 has no VirtualHosts I first followed this guide on setting up Apache to host multiple sites: http://www.debian-administration.org/articles/412 I then found a similar question on ServerFault and tried applying the solution, but it didn't help. Here is an example of my final VirtualHost config: <VirtualHost *:80> ServerAdmin [email protected] ServerName www.xxx.com ServerAlias xxx.com # Indexes + Directory Root. DirectoryIndex index.html DocumentRoot /var/www/www.xxx.com # Logfiles ErrorLog /var/www/www.xxx.com/logs/error.log CustomLog /var/www/www.xxx.com/logs/access.log combined </VirtualHost> with the domain X'd out to protect the innocent :-) Also, I have the conf.d/virtual.conf file mentioned in the guide looking like this: NameVirtualHost * The odd thing is that everything appears to work fine for two of the three sites.

  Read the article

• Why is my Current Printer unavailable in Office ?

  - by cros

  Whenever I try to print any document from Microsoft Office 2007 in Windows Vista 64-bit there is a great possibility that the print job will fail with the following error message: Current printer is unavailable. Select another printer. Only problem is no printer works, not even Bullzip PDF Printer. The only way to resolve this that I have found so far is a reboot, but I don't want to do that all the time. I am using Windows Vista 64-bit. I've had the problem using both SP1 and SP2. The problem occurs on both locally installed and network printers, as well as the virtual printer Bullzip PDF Printer. My primary source of the problem has been Excel, but the error has also occurred in Word. Changing the default printer and restarting the Microsoft Office-application solves this temporarily, but not permanently. Google:ing the error message returns a lot of questions but no solutions, so seems like a frequent problem. What could be a permanent solution for this problem? UPDATE: It seems that my problem stems from me opening MS Office applications by opening a document from Total Commander with administrative rights. This somehow makes the applications not find the printers. Opening MS Office applications either from the Start menu or by opening a document in a non-administrator Explorer allows me to print.

  Read the article

• What is there in Win 7 Pro (or Ultimate) that is not there in Home Premium? - Especially considering this situation..

  - by Senthil

  I want to know the REAL difference between Windows 7 Home Premium and Professional/Utimate. In India, the cost of different versions: Ultimate - 11,200 INR Professional - 10,700 INR Home Premium - 6,600 INR The absolute cost of the first two is so high to me that the difference (500 INR) doesn't matter. So to me there is really no choice between the first two - If I decide to buy the Professional version, I'd rather go for Ultimate itself. What I want to know is, whether Home Premium is enough for my needs. I tried searching for comparison but many look like just marketing junk from MS. They are short and vague. According to this page, the major differences between Pro and HomePremium are Run many Windows XP productivity programs in Windows XP Mode. Connect to company networks easily and more securely with Domain Join. You can do both in Pro but not in Home Premium. I intend to use my Windows 7 for a small business - just starting up. So I'll be dealing with the following: All kinds of development tools, servers Very important - I will run Virtual Machine Software (MS VPC or VMWare or Sun VirtualBox etc..) My system will be acting as the server for most purposes till I can afford dedicated servers. Connect the system to a variety of network devices (PCs, Printers, etc..) Run productivity, business and financial apps Any other small software startup business requirement that I haven't thought of yet. Professional (and Ultimate) is twice as expensive as Home Premium. So it'd be great if someone can point out the things you cannot do with Home Premium, when you use it like I explained above, so that I can make a decision about which one to buy. I need some real-life experiences so that I can make an informed decision - not a decision based on marketing junk.

  Read the article

• Looking for USB Network Attached Storage (NAS) Adapter that supports multiple drives, NTFS/FAT32 fil

  - by braveterry

  I'm looking for a NAS Adapter that supports attaching multiple USB devices to the network. Here's what I'd like to see in a NAS adapter: Under $100.00. Support for multiple devices. This can be through a USB hub or through multiple USB connectors on the device itself. Bittorrent support would be nice, but this isn't a deal-breaker. Filesystem support for at least NTFS or FAT32. I'd prefer to not have to reformat to use the device, but this is also not a deal-breaker. Here is what I am NOT looking for: I'm NOT looking for a NAS enclosure. I already have a couple of spare external USB drives that I'd like to use. I'm NOT looking for a networked USB hub like the one mentioned here. Network USB hubs only allow access to a drive from one PC at a time. I'm NOT looking for a wireless router with a NAS built in. I already have a wireless router, and I'd rather not go through the hassle of replacing it if possible. What I've looked at so far PogoPlug: This supports multiple devices via a USB hub, but there's not Bittorrent support. It's $99.00, so I may end up going with this and hope that they patch in Bittorrent support later. Addonics NAS Adapter: This supports only one device per adapter, so it's a non-starter. SimpleNET NAS Head USB 2.0 Portable Dongle: I'm not 100% sure this supports multiple devices. Plus there doesn't seem to be any Bittorrent support. I'll try to update this post as I explore other devices.

  Read the article

• Audio Static/Interference regardless of audio interface?

  - by Tom

  I currently am running a media center/server on a Lubuntu machine. The machine specs: Core 2 Duo Extreme EVGA SLI 680i MotherBoard 2 GB DDR2 Ram 3 Hard Drives no raid - WD Caviar Black, Green, and Samsung Spinpoint Galaxy GTX 220 1GB External USB Creative XI-FI Extreme Card 550W Power Supply This machine is hooked up through an optical cable to an ONKYO HTR340 Receiver through the XIFI card. Whenever I play any audio regardless if it is through XBMC, the default audio player, a flash video, etc, I get a horrible static sound that randomly gets louder. Here is a video of the sound: http://www.youtube.com/watch?v=SqKQkxYRVA4 This static comes in randomly, sometimes going away for short periods, but eventually always comes back. So far I have tried everything I could think of: Reinstalling OS Installing/upgrading/repairing PulseAudio/Alsa Installing alternate OSes, straight Ubuntu, Lubuntu, Xubuntu, Arch, Mint, Windows 7 Switching audio from the external card to internal Optical, audio out through HDMI, audio out through headphones Different ports on receiver (my main desktop sounds fine on the same sound system) Different optical cables Unplugging everything unnecessary from the motherboard (1 HD, 1 Stick of Ram, 1 Keyboard) Swapping out ram Swapping out the motherboard Replacing the Graphics Card (was replaced due to fan being noisy, not specifically for this problem) Different harddrives Swapping power supply Disabling onboard audio Pretty much everything short of swapping the CPU. I haven't been able to narrow down the problem and it is getting frustrating. Is it possible that the CPU is faulty and might cause a problem such as this, or that the PC case is shorting out the motherboard? Any kind of suggestions will be appreciated.

  Read the article

• How can I trigger the creation of a new CLB file?

  - by Xperimental

  I'm currently having a problem with an application using COM running on Windows Vista. The application runs ok on one machine, but doesn't work on a similar configured machine. Both machines are virtual images originating from the same source image. While searching the registry for causes of this error, I came across the CLBVersion key in HKCR\CLSID which seems to have something to do with COM. The value of the key differs between the two machines (0x6 on the erroneous one, 0xc on the working one). Also there are files containing the same number in their filenames in the %SystemRoot\Registration directories of the machines. They are called R000000000006.clb and R00000000000c.clb respectively. I have already searched the windows event log for anything leading to the creation of those files (I have searched by the creation date of the files). Now a few questions regarding the registry keys and the files: Is it correct, that this is connected to COM? What is the function of the files? What causes the creation of a new "CLBVersion"? Is there a way for me to trigger the creation of a new CLB file? edit: I have now found out, that this has nothing to do with my application error. But I would still be interested in details about the registry key and the files. An installation of Visual Studio 2005 has brought the second machine to the same configuration (0xc in registry and file) as the other one.

  Read the article

• Confusion about Kerberos, delegation and SPNs.

  - by Vilx-

  I already posted this question on SO, but the nature of it is between programming and server configuration, so I'll re-post it here as well. I'm trying to write a proof-of-concept application that performs Kerberos delegation. I've written all the code, and it seems to working (I'm authenticating fine), but the resulting security context doesn't have the ISC_REQ_DELEGATE flag set. So I'm thinking that maybe one of the endpoints (client or server) is forbidden to delegate. However I'm not authenticating against an SPN. Just one domain user against another domain user. As the SPN for InitializeSecurityContext() I'm passing "[email protected]" (which is the user account under which the server application is running). As I understand, domain users have delegation enabled by default. Anyway, I asked the admin to check, and the "account is sensitive and cannot be delegated" checkbox is off. I know that if my server was running as a NETWORK SERVICE and I used an SPN to connect to it, then I'd need the computer account in AD to have the "Trust computer for delegation" checkbox checked (off by default), but... this is not the case, right? Or is it? Also - when the checkbox in the computer account is set, do the changes take place immediately, or must I reboot the server PC or wait for a while?

  Read the article

• IBM HS23 Blade Server (7875) onboard NIC driver for linux

  - by Igor Spivak

  I work with IBM HS23 Blade Server (7875). It's onboard NIC adapter is: Emulex OCl11104-F-X Virtual Fabric Adapter 2-port 10GB and 2-port 1GB LOM . I'm tryed to the following Linux OS with the server: 2.6.32-22-generic-pae #36-Ubuntu SMP. and discovered my OS has not proper Network drive installed (for the NIC adapter described above). After investigation I made, I discovered that the driver I need is "be2net" placed in "net" directory of the linux under the folder "be2net". I managed to download this driver with the latest package for my kernel. Driver info ("modinfo be2net" result) is as follows: --------------------------------------------------------------------------------------- filename: /lib/modules/2.6.32-22-generic-pae/kernel/drivers/net/benet/be2net.ko license: GPL author: ServerEngines Corporation description: ServerEngines BladeEngine2 10Gbps NICDriver 2.101.205 version: 2.101.205 srcversion: 199ADD251CB874C3727CC47 alias: pci:v000019A2d00000710sv*sd*bc*sc*i* alias: pci:v000019A2d00000701sv*sd*bc*sc*i* alias: pci:v000019A2d00000700sv*sd*bc*sc*i* alias: pci:v000019A2d00000221sv*sd*bc*sc*i* alias: pci:v000019A2d00000211sv*sd*bc*sc*i* depends: vermagic: 2.6.32-22-generic-pae SMP mod_unload modversions 586TSC parm: rx_frag_size:Size of a fragment that holds rcvd data. (uint) --------------------------------------------------------------------------------------- After starting linux, I get the following error: be2net 0000:16:00.x: Emulex OneConnect 10Gbps NIC (be3) initilization failed. I checked the same server with another Linux version (Red-Had 5.5.1.0) and the NICs worked properly, so seems there is no problem in HW. Also, on IBM or Emulex offical sites I managed to find drivers only for Red-Had and SUSE versions.

  Read the article

• MSSQL 2000 installation error: Setup failed to configure the server. Refer to the server error logs.

  - by kaneuniversal

  I'm trying to install MSSQL 2000 on a virtual Windows 2003 instance. However, every time I run the install program, it fails to start the service. This is the error log: 21:46:50 C:\Program Files\Microsoft SQL Server\80\Tools\Binn\cnfgsvr.exe -F "C:\WINDOWS\sqlstp.log" -I MSSQLSERVER -V 1 -M 0 -Q "SQL_Latin1_General_CP1_CI_AS" -H 131408 -U sa -P ############################################################################### Starting Service ... SQL_Latin1_General_CP1_CI_AS -m -Q -T4022 -T3659 Connecting to Server ... driver={sql server};server=xxxxxxxxxx;UID=sa;PWD=;database=master [Microsoft][ODBC SQL Server Driver]Timeout expired driver={sql server};server=xxxxxxxxxx;UID=sa;PWD=;database=master [Microsoft][ODBC SQL Server Driver]Timeout expired driver={sql server};server=xxxxxxxxxx;UID=sa;PWD=;database=master [Microsoft][ODBC SQL Server Driver]Timeout expired SQL Server configuration failed. ############################################################################### 21:49:34 Process Exit Code: (-1) 22:19:04 Setup failed to configure the server. Refer to the server error logs and C:\WINDOWS\sqlstp.log for more information. 22:19:04 Action CleanUpInstall: 22:19:04 C:\DOCUME~1\ADMINI~1\LOCALS~1\Temp\1\SqlSetup\Bin\scm.exe -Silent 1 -Action 4 -Service SQLSERVERAGENT 22:19:05 Process Exit Code: (1060) The specified service does not exist as an installed service. 22:19:05 C:\DOCUME~1\ADMINI~1\LOCALS~1\Temp\1\SqlSetup\Bin\scm.exe -Silent 1 -Action 4 -Service MSSQLSERVER 22:19:05 Process Exit Code: (0) 22:19:05 StatsGenerate returned: 2 22:19:05 StatsGenerate (0x0,0x1,0xf00000,0x200,1033,303,0x0,0x1,0,0,0 22:19:05 StatsGenerate -1,Administrator) 22:19:05 Installation Failed. Has anyone had this problem? Any ideas about how to fix it? Thanks very much, Michael

  Read the article

• Toshiba Portege M400 screen rotation not working under Windows 7 x64

  - by Christi

  I have installed Windows 7 on my Toshiba Portege M400. This in itself was relatively tricky.* However, the button utilities aren't quite working for me. One of the buttons tries to launch the Toshiba Assist program, which doesn't appear to be available under Windows 7 for the M400, but this I can live without. More important is that the screen won't rotate as it is supposed to when you hold the "cancel" (X in a circle) button on the bezel. The PC is set to run "C:\Program Files (x860\Toshiba\Toshiba Rotation Utility\phtrot.exe". There is a "trot.exe" file in the same directory (the former appears to be to cause slightly different behaviour when rotation is done by press and hold). Neither of these programs rotates the screen either by using the buttons or from the command line. The screen is rotating normally when switching from tablet to laptop mode, so there does not appear to be an inherent problem with rotation. I'd just like to be able to use the buttons on the side of the screen to change the screen orientation. Windows XP used to have a "setrot" utility to do this, but that seems to have gone in Windows 7 Thanks for your help. *Just in case anyone comes looking for how to do this, you need to extract driver files from http://cdgenp01.csd.toshiba.com/content/support/downloads/util_raid_os2007252a.exe, which does not seem to be listed among the available files for the m400. This executable contains the SATA interface drivers that will need to be loaded by the installer before it can see your hard disk drive. It needs to be unpacked and the files copied to a USB key which they can then be loaded from in the install process. The utilities etc. for installation post windows install are all available from the Toshiba USA support website.

  Read the article

• Non-functioning AutoFilter on Locked Cells in Office 2008 - works in Office 2007

  - by Sarcas

  I'm looking into a problem for someone, who works in a mixed OS environment. She has created an Excel spreadsheet in Office 2007 to act as a directory, with AutoFilter turned on for names, email addresses, departments etc. To make sure no one accidentally edits email addresses (for example), she has protected the work sheet. Accessing this worksheet on a PC running Excel 2007, everything runs as you'd expect. You can filter the sheet by any of the auto-filtered columns, and because the sheet is protected, the data integrity is guaranteed. However, if you access the sheet on a Mac running Excel 2008, you can't filter the columns. What's strange here is that the AutoFilter dropdown arrows do appear in each of the column headers as you would expect. It's just that nothing happens if you click on them. If you select one of the column header cells (say, 'First Name') and check the menu: Data-Filter, you can see that AutoFilter is ticked. As another datapoint, you also seem to be able to apply an Advanced filter to these rows on the protected sheets. Does anyone know why this might be? It seems to be a compatibility issue between Excel 2007/2008 (I know the codebase isn't the same), but I can't find any references to it in documentation or forums anywhere, and it would be good to know if there's a way around this. Thanks!

  Read the article

• Personal VPN Solutions

  - by dragonmantank

  I want to set up a VPN for my laptop to connect back at home so that I don't have to directly expose my desktop computer to the internet. Here is what I have: Internet -> DD-WRT v24sp1-mega -> Desktop PC w/ Windows 7 Ultimate -> MacBook w/ OSX 10.6 What would be the easiest thing to do? DD-WRT has PPTP and OpenVPN built in and Windows 7 has RRAS itself but thus far I've run into some problems. Are there any other alternatives, or suggestions on getting these to work? PPTP I tried setting up PPTP directly on DD-WRT using these directions. When I tried connecting using my external IP from the MacBook I just kept getting that the remote server did not respond. OpenVPN According to the instructions here I don't have enough open nvram to set up OpenVPN. RRAS I got RRAS set up without a problem and can connect from the MacBook to the Windows 7 box while I'm on the same network. I port forwarded 1723 on the DD-WRT back to the Windows 7 box and made sure that PPTP Passthrough was enabled. Again, like PPTP, it just kept timing out.

  Read the article

• Access All VLANS over XenServer Interface

  - by Garrett

  For my current setup, I have a physical NIC on a XenServer machine that receives traffic tagged with various VLAN IDs. I have a virtual machine that is running Vyatta that needs to be able to access both tagged and untagged traffic in order to route traffic. Here's the problem: 1) If I bind the NIC in XenCenter to the VM (which has no VLAN ID associated with it), the VM cannot see any tagged traffic. I have verified this using tcpdump. However, the tagged traffic is flowing into the XenServer machine perfectly fine. 2) I have more than 7 VLANs, so adding each VLAN as an interface within XenCenter isn't an option. 3) Even though tcpdump shows no tagged traffic coming in the VMs NIC, I have tried adding VLAN interfaces within Vyatta. This also doesn't work. I have tried using both Linux bridge and openvswitch setups and neither seem to work. I am running XenServer 6.0.3 free and Vyatta VC6.3. Please help! I've run out of ideas. I've googled for hours and can't seem to find anything.

  Read the article

• Booting the server redis no errors

  - by Tylër

  The redis but usually begins with the following errors: tyler @ tyler-vortex: ~ / pens $. / src / redis-server [3690] Dec 01 10:56:05 # Warning: the specified config file, using the default config. In order to Specify a config file use 'redis-server / path / to / redis.conf' [3690] Dec 01 10:56:05 # Unable to set the max number of files limit to 10032 (Operation not permitted), setting the max configuration to 992 clients. Others errors founds: tyler@tyler-vortex:~/redis$ sudo ./utils/install_server.sh Welcome to the redis service installer This script will help you easily set up a running redis server Please select the redis port for this instance: [6379] Selecting default: 6379 Please select the redis config file name [/etc/redis/6379.conf] Selected default - /etc/redis/6379.conf Please select the redis log file name [/var/log/redis_6379.log] Selected default - /var/log/redis_6379.log Please select the data directory for this instance [/var/lib/redis/6379] Selected default - /var/lib/redis/6379 Please select the redis executable path [/usr/local/bin/redis-server] cat: ./redis.conf.tpl: Arquivo ou diretório não encontrado cat: ./redis_init_script.tpl: Arquivo ou diretório não encontrado ERROR: Could not write init script to /tmp/6379.conf. Aborting! Furthermore, I would like to know how to configure it not to consume so much RAM. Follow the memory configuration of our website, but the settings of "vm-*" does not exist in the file redis.conf. http://redis.io/topics/virtual-memory You have to create them? * Edit: I installed. After that, I believe that I no longer have access via. / Src / redis-server, because it happens: tyler@tyler-vortex:~$ cd redis/ tyler@tyler-vortex:~/redis$ ./src/redis-server [2616] 01 Dec 22:29:30 # Warning: no config file specified, using the default config. In order to specify a config file use 'redis-server /path/to/redis.conf' [2616] 01 Dec 22:29:30 # Opening port 6379: bind: Address already in use tyler@tyler-vortex:~/redis$ But there's another detail, the redistribution starts with the system .. redis 127.0.0.1:6379> exit tyler@tyler-vortex:~/redis$ ./src/redis-cli redis 127.0.0.1:6379> exit ... but how can I now see that the communication had before you installed from. sh?

  Read the article

• Installing messaging software displays error 1324 invalid character

  - by llykke

  Trying to install Reuters Messaging software onto a windows 7 pc we receive the error message Error 1324: The folder path 'My Documents' contains an invalid character We've tried installing the application using the local admin account and the user account which is an AD account (roaming?). This user account has administrative rights (i.e. should be allowed to install applications). The users 'My Documents' folder is located on a network drive, where only the user has access. We've tried experimenting with the HKEY_CURRENT_USER \ Software \ Microsoft \ Windows \ CurrentVersion \ Explorer\ User Shell Folders registry entries and setting them to a local position (i.e. C:\Users\Username\Documents) but this didn't resolve the error. We've also tried the following which was taken from a website I can't remember the name of: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\FileSystem Select the NtfsDisable8dot3NameCreation entry and change the value to 0 Select the Win31FileSystem entry and change the value to 0 which didn't resolve the issue. Edit: This was also an issue when attempting to install the citrix native client necessary to run citrix application (*.ica extension). This made the same error box appear.

  Read the article

• VMWare ESX, storage over 2TB

  - by Phliplip

  Hi, First of, i'm a webdeveloper and my server experience lies in setting up FreeBSD servers for webserver. I'm working on a project for at photographer, and i'm hired to develop a new online photo ordering system - where user of course can view their photos :) They have a massive need of storage, thus we have bought a HP G6 and 8x1TB SATA HDD. Our plan is to install VMWare ESX 4.0, running multiple virtual machines; FreeBSD 8 for webserver and some windows servers. Allready done that. Then mount one big storage to the BSD, and share it through Samba to the WinServers. The raid is set up with an array of 2x 1TB to handle the VMs. And the rest is setup as 3 2x1TB to handle the photo-data. Thus 2.73TB for photo-data (the raids are 1+0). Now if we add a datastore in the ESX and add the 3 LUNs we can get a datastore of 2.74TB. But i don't se how i can add this datastore direct to the VM. Only the BSD VM needs access to this. Only way is to create a VirtualDisk, with a max of 2TB (8MB blocksize). This is because the datastore where we save the virtualdisk has a maximum filesize of 2TB. Then add it as a harddisk to the BSD VM. In the 'Add Harddisk' pane for the VM, i see an option for Raw Disk Management. I think this is to access the datastore or the raid directly. Only problem is that its greyed out! Can i access the datastorage directly from the BSD? Without creating and adding virtualdisk.

  Read the article

< Previous Page | 583 584 585 586 587 588 589 590 591 592 593 594  | Next Page >