Search Results

Search found 9105 results on 365 pages for 'disk quota'.

Page 59/365 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

  • Should I use "Raid 5 + spare" or "Raid 6"?

    - by Trevor Boyd Smith
    What is "Raid 5 + Spare" (excerpt from User Manual, Sect 4.17.2, P.54): RAID5+Spare: RAID 5+Spare is a RAID 5 array in which one disk is used as spare to rebuild the system as soon as a disk fails (Fig. 79). At least four disks are required. If one physical disk fails, the data remains available because it is read from the parity blocks. Data from a failed disk is rebuilt onto the hot spare disk. When a failed disk is replaced, the replacement becomes the new hot spare. No data is lost in the case of a single disk failure, but if a second disk fails before the system can rebuild data to the hot spare, all data in the array will be lost. What is "Raid 6" (excerpt from User Manual, Sect 4.17.2, P.54): RAID6: In RAID 6, data is striped across all disks (minimum of four) and a two parity blocks for each data block (p and q in Fig. 80) is written on the same stripe. If one physical disk fails, the data from the failed disk can be rebuilt onto a replacement disk. This Raid mode can support up to two disk failures with no data loss. RAID 6 provides for faster rebuilding of data from a failed disk. Both "Raid 5 + spare" and "Raid 6" are SO similar ... I can't tell the difference. When would "Raid 5 + Spare" be optimal? And when would "Raid 6" be optimal"? The manual dumbs down the different raid with 5 star ratings. "Raid 5 + Spare" only gets 4 stars but "Raid 6" gets 5 stars. If I were to blindly trust the manual I would conclude that "Raid 6" is always better. Is "Raid 6" always better?

    Read the article

  • Why does OS X insist on spinning up all external drives when loading a file from the local drive?

    - by Phillip Oldham
    Why does OS X insist on spinning up all the attached external drives (firewire, usb) when loading a file from the local (internal) drive? It's driving me insane that I have to wait for 3 attached drives (1 back-up, 2 media) to spin up -- a total of 20s -- to access a file that is located only on my local/internal drive. There is no obvious need to access the other drives; nothing is being read from them and nothing need be written. Examples: Quicktime X opening a file from the local HDD. Starting Caffeine, an app which doesn't access any other files at all. Can I tell OS X to only spin those drives up when actually accessing them?

    Read the article

  • CloneZilla PXE Boot Without NFS

    - by John
    I am trying to setup CloneZilla to be bootable via PXE without using NFS. I do not have NFS running on our PXE server and would like to keep it that way. However, most of the information that I have found online indicates that you need to setup NFS in order to PXE boot CloneZilla. I believe that I am pretty close in getting it to work, but am not sure where to go next. Listed below are the different PXE menu option configurations that I have used so far. LABEL Clonezilla Live MENU LABEL Clonezilla Live KERNEL utilities/clonezilla/vmlinuz APPEND initrd=utilities/clonezilla/initrd.img boot=live live-config noswap nolocales edd=on nomodeset ocs_live_run="ocs-live-general" ocs_live_extra_param="" ocs_live_keymap="" ocs_live_batch="no" o$ I have also tried the following append lines, without success: APPEND initrd=utilities/clonezilla/initrd.img boot=live union=aufs noswap noprompt vga=788 fetch=tftp://10.130.155.23/filesystem.squashfs APPEND initrd=utilities/clonezilla/initrd.img boot=live union=aufs noswap noprompt vga=normal nomodeset nosplash fetch=tftp://10.130.155.23/filesystem.squashfs Each of them have resulted in a no go with the following error: "Unable to find a live file system on the network". It looks like it gets to the point of trying to load the filesystem.squashfs file, hangs, and then throws the error. Any help would be greatly appreciated.

    Read the article

  • what is acceptable datastore latency on VMware ESXi host?

    - by BeowulfNode42
    Looking at our performance figures on our existing VMware ESXi 4.1 host at the Datastore/Real-time performance data Write Latency Avg 14 ms Max 41 ms Read Latency Avg 4.5 ms Max 12 ms People don't seem to be complaining too much about it being slow with those numbers. But how much higher could they get before people found it to be a problem? We are reviewing our head office systems due to running low on storage space, and are tossing up between buying a 2nd VM host with DAS or buying some sort of NAS for SMB file shares in the near term and maybe running VMs from it in the longer term. Currently we have just under 40 staff at head office with 9 smaller branches spread across the country. Head office is runnning in an MS RDS session based environment with linux ERP and mail systems. In total 22 VMs on a single host with DAS made from a RAID 10 made of 6x 15k SAS disks.

    Read the article

  • MD3200 - 3 to 4x less throughput than MD1220. Am I missing something here?

    - by Igor Polishchuk
    I have two R710 servers with similar configuration. One in my office has MD1220 attached. Another one in the datacenter of my hosting services vendor has MD3200. I'm getting significantly worse throughput from MD3200 at my vendors setup. I'm mostly interested in sequential writes, and I'm getting these results in bonnie++ and dd tests: Seq. writes on MD1220 in my office: 1.1 GB/s - bonnie++, 1.3GB/s - dd Seq. writes on MD3200 at my vendor's: 240MB/s - bonnie++, 310MB/s - dd Unfortunately, I could not test the exactly the same configurations, but the two I have should be comparable. If anything, my good performing environment is cheaper than the bad performing. I expect at least similar throughput from these two setups. My vendor cannot really help me. Hopefully, somebody more familiar with the DAS performance can look at it and tell if I'm missing something here and my expectations are too high. To summarize, the question here is it reasonable to expect about 100MB/s of sequential write throughput per each couple of drives in RAID10 on MD3200? Is there any trick to enable such performance in MD3200 with dual controller as opposed to simple MD1220 with a single H800 adapter? More details about the configurations: A good one in my office: Dell R710 2CPU X5650 @ 2.67GHz 12 cores 96GB DDR3, OS: RHEL 5.5, kernel 2.6.18-194.26.1.el5 x86_64 20x300GB 2.5" SAS 10K in a single RAID10 1MB chunk size on MD1220 + Dell H800 I/O controller with 1GB cache in the host Not so good one at my vendor's: Dell R710 2CPU L5520 @ 2.27GHz 8 cores 144GB DDR3, OS: RHEL 5.5, kernel 2.6.18-194.11.4.el5 x86_64 20x146GB 2.5" SAS 15K in a single RAID10 512KB chunk size, Dell MD3200, 2 I/O controllers in array with 1GB cache each Additional information. I've also ran the same tests on the same vendor's host, but the storage was: two raids of 14x146GB 15K RPM drives RAID 10, striped together on the OS level on MD3000+MD1000. The performance was about 25% worse than on MD3200 despite having more drives. When I ran similar tests on the internal storage of my vendor's host (2x146GB 15K RPM drives RAID1, Perc 6i) I've got about 128MB/s seq. writes. Just two internal drives gave me about a half of 20 drives' throughput on MD3200. The random I/O performance of the MD3200 setup is ok, it gives me at least 1300 IOPS. I'm mostly have problems with sequentioal I/O throughput. Thank you for looking into it. Regards Igor

    Read the article

  • The difference between desktop-series HDD drives and server-series

    - by FractalizeR
    Hello. What are the main differences between desktop-series hard disks and server-series? The obvious things I can see are: durability (server hardware mostly more qualitative and have more warranty) and power consumption (server hardware more focused on performance, than on power economy). Also server disks are usually a little faster, but it seems, that it is not always the case. May be there are some other reasons, that make you choose server-oriented series (Seagate ES drives, for example) over desktop-oriented ones (Seagate Barracuda series)? What are they?

    Read the article

  • Migration with SysPrep, ImageX and

    - by Jack Smith
    I know that you can use SysPrep and ImageX to create a prepared image that can be used on several systems but the question is. How well does it work in a corporate environment of moving machines from old hardware off to new harddrives and new hardware? EDIT: The system runs accounting software and databases. So would SysPrep remove all License keys and other information which means would cause problems right? Would something else be a better option even though there are heavy costs involved? Currently, when I clone/copy the drive, Windows will black screen on me. So I need something with differential hardware support?

    Read the article

  • Cannot resize OS X partition

    - by David Pearce
    I am trying to resize my existing Mac OS Extended partition on my Macbook to install Windows 7 (using steps similar to these), but when ever I go to apply the changes, I get this error: Partition failed Partition failed with the error: The partition cannot be resized. Try reducing the amount of change in the size of the partition. The total capacity of the hard drive in question is 260GB, with the entirety being taken up by the OS X boot partition. There is I am aiming to shrink that partition down to 60GB. How can I fix this problem? I have been reducing the amount of change by 10GB each attempt, but it still is not working. I assume the problem is that there is not a large amount of continuous space on the device. Is there some way to can do a manual defrag that would rectify this problem?

    Read the article

  • What usb-bootable utility should I use to copy SATA hard drives?

    - by Steve Brown
    I have a computer that only has two SATA connections and I need to copy one SATA hard drive to another. Since I have to unplug the CD drive to copy the drives I need a USB-bootable utility. I have an old school copy of Norton Ghost (CD based): Ghost has always worked well for me in the past - I see there is a new "version 15" out but I'm not sure if it is worth buying. A friend has Acronis True Image on a USB drive: We tried to use that on the computer but it was unable to copy both partitions (restore partition and main partition). Of course there may be some problem with the drive that is keeping Acronis from working (it is just exiting with a lame error about not being able to copy the disks and no error code or detailed information), but I'm interested in knowing if there is a better, more solid, or widely used solution that I should invest in. What usb-bootable utilities can I use to copy SATA hard drives?

    Read the article

  • What would I need to do to clone a Linux install to another machine?

    - by Marcus Hughes
    Basically, I want to make an image of one Linux install I have, and distribute it over similar (if not identical) spec machines on a network. I know it is possible, however am unsure of what needs to be done before I make the image of the install to ensure it works correctly on all machines. First think I know needs to be done, is remove all interface configuration, as I assume it would just jump to eth1 (and possibly use the same MAC), as it wont locate the network interface it had before, how would I do this so it auto detects and goes to eth0 again? Is there anything else I would need to do to the install before I make its image?

    Read the article

  • General monitoring for SQL Server Analysis Services using Performance Monitor

    - by Testas
    A recent customer engagement required a setup of a monitoring solution for SSAS, due to the time restrictions placed upon this, native Windows Performance Monitor (Perfmon) and SQL Server Profiler Monitoring Tools was used as using a third party tool would have meant the customer providing an additional monitoring server that was not available.I wanted to outline the performance monitoring counters that was used to monitor the system on which SSAS was running. Due to the slow query performance that was occurring during certain scenarios, perfmon was used to establish if any pressure was being placed on the Disk, CPU or Memory subsystem when concurrent connections access the same query, and Profiler to pinpoint how the query was being managed within SSAS, profiler I will leave for another blogThis guide is not designed to provide a definitive list of what should be used when monitoring SSAS, different situations may require the addition or removal of counters as presented by the situation. However I hope that it serves as a good basis for starting your monitoring of SSAS. I would also like to acknowledge Chris Webb’s awesome chapters from “Expert Cube Development” that also helped shape my monitoring strategy:http://cwebbbi.spaces.live.com/blog/cns!7B84B0F2C239489A!6657.entrySimulating ConnectionsTo simulate the additional connections to the SSAS server whilst monitoring, I used ascmd to simulate multiple connections to the typical and worse performing queries that were identified by the customer. A similar sript can be downloaded from codeplex at http://www.codeplex.com/SQLSrvAnalysisSrvcs.     File name: ASCMD_StressTestingScripts.zip. Performance MonitorWithin performance monitor,  a counter log was created that contained the list of counters below. The important point to note when running the counter log is that the RUN AS property within the counter log properties should be changed to an account that has rights to the SSAS instance when monitoring MSAS counters. Failure to do so means that the counter log runs under the system account, no errors or warning are given while running the counter log, and it is not until you need to view the MSAS counters that they will not be displayed if run under the default account that has no right to SSAS. If your connection simulation takes hours, this could prove quite frustrating if not done beforehand JThe counters used……  Object Counter Instance Justification System Processor Queue legnth N/A Indicates how many threads are waiting for execution against the processor. If this counter is consistently higher than around 5 when processor utilization approaches 100%, then this is a good indication that there is more work (active threads) available (ready for execution) than the machine's processors are able to handle. System Context Switches/sec N/A Measures how frequently the processor has to switch from user- to kernel-mode to handle a request from a thread running in user mode. The heavier the workload running on your machine, the higher this counter will generally be, but over long term the value of this counter should remain fairly constant. If this counter suddenly starts increasing however, it may be an indicating of a malfunctioning device, especially if the Processor\Interrupts/sec\(_Total) counter on your machine shows a similar unexplained increase Process % Processor Time sqlservr Definately should be used if Processor\% Processor Time\(_Total) is maxing at 100% to assess the effect of the SQL Server process on the processor Process % Processor Time msmdsrv Definately should be used if Processor\% Processor Time\(_Total) is maxing at 100% to assess the effect of the SQL Server process on the processor Process Working Set sqlservr If the Memory\Available bytes counter is decreaing this counter can be run to indicate if the process is consuming larger and larger amounts of RAM. Process(instance)\Working Set measures the size of the working set for each process, which indicates the number of allocated pages the process can address without generating a page fault. Process Working Set msmdsrv If the Memory\Available bytes counter is decreaing this counter can be run to indicate if the process is consuming larger and larger amounts of RAM. Process(instance)\Working Set measures the size of the working set for each process, which indicates the number of allocated pages the process can address without generating a page fault. Processor % Processor Time _Total and individual cores measures the total utilization of your processor by all running processes. If multi-proc then be mindful only an average is provided Processor % Privileged Time _Total To see how the OS is handling basic IO requests. If kernel mode utilization is high, your machine is likely underpowered as it's too busy handling basic OS housekeeping functions to be able to effectively run other applications. Processor % User Time _Total To see how the applications is interacting from a processor perspective, a high percentage utilisation determine that the server is dealing with too many apps and may require increasing thje hardware or scaling out Processor Interrupts/sec _Total  The average rate, in incidents per second, at which the processor received and serviced hardware interrupts. Shoulr be consistant over time but a sudden unexplained increase could indicate a device malfunction which can be confirmed using the System\Context Switches/sec counter Memory Pages/sec N/A Indicates the rate at which pages are read from or written to disk to resolve hard page faults. This counter is a primary indicator of the kinds of faults that cause system-wide delays, this is the primary counter to watch for indication of possible insufficient RAM to meet your server's needs. A good idea here is to configure a perfmon alert that triggers when the number of pages per second exceeds 50 per paging disk on your system. May also want to see the configuration of the page file on the Server Memory Available Mbytes N/A is the amount of physical memory, in bytes, available to processes running on the computer. if this counter is greater than 10% of the actual RAM in your machine then you probably have more than enough RAM. monitor it regularly to see if any downward trend develops, and set an alert to trigger if it drops below 2% of the installed RAM. Physical Disk Disk Transfers/sec for each physical disk If it goes above 10 disk I/Os per second then you've got poor response time for your disk. Physical Disk Idle Time _total If Disk Transfers/sec is above  25 disk I/Os per second use this counter. which measures the percent time that your hard disk is idle during the measurement interval, and if you see this counter fall below 20% then you've likely got read/write requests queuing up for your disk which is unable to service these requests in a timely fashion. Physical Disk Disk queue legnth For the OLAP and SQL physical disk A value that is consistently less than 2 means that the disk system is handling the IO requests against the physical disk Network Interface Bytes Total/sec For the NIC Should be monitored over a period of time to see if there is anb increase/decrease in network utilisation Network Interface Current Bandwidth For the NIC is an estimate of the current bandwidth of the network interface in bits per second (BPS). MSAS 2005: Memory Memory Limit High KB N/A Shows (as a percentage) the high memory limit configured for SSAS in C:\Program Files\Microsoft SQL Server\MSAS10.MSSQLSERVER\OLAP\Config\msmdsrv.ini MSAS 2005: Memory Memory Limit Low KB N/A Shows (as a percentage) the low memory limit configured for SSAS in C:\Program Files\Microsoft SQL Server\MSAS10.MSSQLSERVER\OLAP\Config\msmdsrv.ini MSAS 2005: Memory Memory Usage KB N/A Displays the memory usage of the server process. MSAS 2005: Memory File Store KB N/A Displays the amount of memory that is reserved for the Cache. Note if total memory limit in the msmdsrv.ini is set to 0, no memory is reserved for the cache MSAS 2005: Storage Engine Query Queries from Cache Direct / sec N/A Displays the rate of queries answered from the cache directly MSAS 2005: Storage Engine Query Queries from Cache Filtered / Sec N/A Displays the Rate of queries answered by filtering existing cache entry. MSAS 2005: Storage Engine Query Queries from File / Sec N/A Displays the Rate of queries answered from files. MSAS 2005: Storage Engine Query Average time /query N/A Displays the average time of a query MSAS 2005: Connection Current connections N/A Displays the number of connections against the SSAS instance MSAS 2005: Connection Requests / sec N/A Displays the rate of query requests per second MSAS 2005: Locks Current Lock Waits N/A Displays thhe number of connections waiting on a lock MSAS 2005: Threads Query Pool job queue Length N/A The number of queries in the job queue MSAS 2005:Proc Aggregations Temp file bytes written/sec N/A Shows the number of bytes of data processed in a temporary file MSAS 2005:Proc Aggregations Temp file rows written/sec N/A Shows the number of bytes of data processed in a temporary file 

    Read the article

  • ext4 jbd2 journaling active even on empty filesystem

    - by Paul
    I have been having several issues with my ext4 filesystems that seem to be due to jbd2 journaling. I made a related post here and am rephrasing it with the hope that someone may be able to help. For a minimal example, I start with an empty 8gb USB stick and use gparted to create one ext4 partition. The command used by gparted when creating the ext4 file system is: mkfs.ext4 -j -O extent -L DataTraveler8gb /dev/sde1 I check the filesystem with gparted: e2fsck -f -y -v /dev/sde1 and I mount it: sudo mount /dev/sde1 /media/test The disk is empty, but the journaling is very active on this disk (/dev/sde1). The other disks are ext4 SSDs formatted similarly. A snapshot of iotop: % sudo iotop -oPa Total DISK READ: 0.00 B/s | Total DISK WRITE: 2027.21 K/s PID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 262 be/3 root 0.00 B 56.00 K 0.00 % 0.18 % [jbd2/sda1-8] 29069 be/3 root 0.00 B 0.00 B 0.00 % 0.16 % [jbd2/sde1-8] 891 be/3 root 0.00 B 4.00 K 0.00 % 0.03 % [jbd2/sdc1-8] What is jbd2 doing with /dev/sde1? If I follow the same steps with a larger 2Tb disk, iotop indicates this empty disk is constantly being written to by jbd2 at the rate of Mb/s as soon as I mount it. On the other disks, which have the OS and /home, I have tried to find if any files are being modified by processes to cause this behavior but couldn't find any. I also moved many of the disk intensive process to use a tmpfs. And used noatime. I have another non-SSD hard disk on this machine, /dev/sdb, that is also ext4 but was not formatted by gparted (given to me by a coworker). It does not appear in iotop. So I am assuming there an issue with gparted. Any suggestions are appreciated. Also any tips on how to modify existing partitions to fix the issue without having to start from scratch would be great. There are some posts related to jbd2 but they didn't help (eg. here).

    Read the article

  • Disabling partition just for one OS on multi-boot system

    - by Emiswelt
    Hi Regarding to the solution there: http://serverfault.com/questions/36385/how-can-i-mount-a-hard-drive-as-read-only-on-windows-xp I have a system with three partitions. One runs windows 7, one runs windows XP and is for some experimental programming and testing. I don't want to mess up anything, so I am going to disable the windows 7 partition like described on the linked page above from windows XP to protect the operating system. When I do this, is the windows 7 partition only disabled for the running XP os, or is the windows 7 partition rendered unbootable? with best regards

    Read the article

  • Simple Workstation Imaging Solution?

    - by user23087
    I need a fairly cheap imaging solution for Windows XP corporate desktops. Ideally, I'd be able to set up a desktop exactly as we want it, create an image, deploy this image to a server, then boot a new desktop to a CD/USB Drive/Network and quickly set up the workstation. Ideally, each computer would also have a unique workstation name. Any ideas? Right now I'm using a custom built Linux DD solution, but it's slow, not network-based, can't image multiple computers at the same time as there's only one copy on a USB drive, and can't uniquely name the computers. Thanks, Will

    Read the article

  • ubuntu hardrive repartition without uninstalling ubuntu or windows 7 and losing data of hardrive

    - by user141692
    I have and asus r500v with 750 gb gpt system uefi motherboard core i7 3610qm, nvidia geforce gt, with ubuntu and w7 dual boot, I had problems installing ubuntu because of the grub but I fix it with https://bugs.launchpad.net/ubuntu/+source/grub2/+bug/807801, but I still have the problem of "warning: the partition is misaligned by 3072 bytes. this may result iin very poor performance. Repartitioning is suggested" in every linux partitioin I made and my 750 gb is not being used at the maximun capacity it only uses 698 gb. I want to make partitions so that the warning doesnt show up and I can use the maximum capacity of the HDD, as I did with another dual boot laptop (compaq presario cq40). I have the following partitions: unknown 1.0Mb: partition type: lynux Basic DAta partition, device: /dev/sda2 Usage: --, Partition flags: --, partition label:-- warning: the partition is misaligned by 3072 bytes. this may result in very poor performance. repartitioning is suggested. -system 210 Mb FAt, usage: Filesystem, partition type: EFI system Partition, Partition Flags:--, Label: system, Device: /dev/sda1, partition label: EFI system partition, Capacity 210MB, avilable:--, Mount Point: mounted at /boot/efi -134 Mb NTFS, usage: filesystem, partition type: linux basic data partition, partition flags:.--, device: /dev/sda7, partition label: --, capacity: 134MB,available:--, mount point: not mounted -OS 250 GB NTFS, usage: file system, partititon type: linux basic data partition, partition flags: --, type: NTFS, label: OS, device: /dev/sda3, partition label: basic data partition, capacity: 250 GB, available:-, mount point: not mounted -10GB FAT 32, usage: filesystem, partition type: EFI system partition, partition flags:--, type: FAT 32, label: --, device: /dev/sda4, partition label: --, capacity: 10GB, available:--, mount point: not mounted warning: the partition is misaligned by 3072 bytes. this may result in very poor performance. repartitioning is suggested. -10gb ext 4, usage: file system, partition type: linux basic data partition, partition flags:--, type: EXT4(version1) label:--, device: /dev/sda9, partition label:--, capacity: 10 GB, available:--, mount point at / warning: the partition is misaligned by 1536 bytes. this may result in very poor performance. repartitioning is suggested. -478GB ext4, usage: filesystem, partition type: linux basic data partition, partition flags:--, type: EXT4, label:--, device: /dev/sda5, partition label:--, capacity: 478gb, available:--, mount point: mounted at /home warning: the partition is misaligned by 512 bytes. this may result in very poor performance. repartitioning is suggested. -2.0gb Swap 2.0Gb, usage: swap space, partition type: linux swap partitioin, partition flags:-, device: /dev/sda6, partition label: capacity: 2.0gb warning: the partition is misaligned by 512 bytes. this may result in very poor performance. repartitioning is suggested. and as you can see it is not well organized so please help me to organize the partitions witahout uninstalling the w7, and if possible the grub2

    Read the article

  • How can I free up some space in my C: drive?

    - by Faraaz
    Each time I try to save a file, I get a message from my computer (with Windows 7) that asks me to free up some space in my Drive C before being able to save my intended file. But the more I search for extraneous files to delete, the more I get frustrated. I simply can't find out what "extra" file(s) I have that are occupying about 20 gigs of my C drive. As far as I know I save all the downloadable stuff to my other drives, and the most part of what I do with my computer is just Internet browsing. Would you please help me find the file or files that have occupied so much space in my Drive C so that I can remove them?

    Read the article

  • Are there any Microsoft Exchange Clients for iOS and Android that store their local data in an encrypted manner?

    - by Zac B
    I don't feel like this is a product recommendation question, more of a "does this tech even exist and is it feasible" question, but if I'm wrong, feel free to give this question the boot. Context: Our company has a bunch of traveling employees who access the company's Exchange server via thier iDevices or android phones, but because of the data protection laws in the state where our company is based (and the nature of the data our company works with), a recent security audit found that all mobile devices (laptops, phones, etc) operated by our company need to have all company correspondence and related data encrypted all the time. For laptops, that was easy: BitLocker or TrueCrypt, problem solved. For phones and tablets, however, I'm stumped. Sure, you can put lock screens/passwords on the phones, but the data is still accessible via external extraction, as law enforcement authorities already know. Question: Are there any clients for Microsoft Exchange that run on iOS or Android which store local data encrypted? The people using our mobile devices do a lot of their work while offline, so just giving them OWA access with SSL connection security isn't enough. Are there apps/technologies that present an additional login credential prompt to decrypt locally stored data in the app's storage area on the phone? My gut reaction when I started looking into this was "that doesn't sound like something Apple would allow into the App Store", but I've been wrong before...

    Read the article

  • partition alignment on fresh windows 2003 ent server

    - by Datapimp23
    Hi, I have this server which has it's physical disks in RAID 5 controlled by a 3com raid controller. size of the stripe unit is unknown for the moment (Can check tomorrow in the office). I need to install windows server 2003 ENT and create 2 partitions (OS, Data). I'd like to create the partitions before the installation on windows server. They have to be aligned properly. I have the newest version of gparted on a disc but I have no clue if this is the right tool. Can someone point me in the right direction? Thanks

    Read the article

  • Setting up a Pagefile and Partition in Server 2008

    - by Brett Powell
    I am setting up 18 new machines for our company, and I have instructions from my new boss on setting up a Pagefile and Partition. I have looked at their existing machines to base the new setups off of, but there is no consistency between any 2 machines, which has left me extremely frustrated to say the least. My instructions are... 1) Set a static pagefile (use recommended value as max/min), set it on SSD if SSD available. 2) Make 3 partitions: C: is used for OS and install files D: is used for backups on machines with a SSD. On machines without SSD create a D: partition for pagefile (2*installed RAM for partition size) E: must be the partition hosting user files I have never messed with Pagefiles before, and looking at their existing machines is offering no help. My questions are... 1) As the machines I am setting up have no SSD (just 2 SATA drives) does it sound like the Pagefile should be setup on the C: (primary) drive or the D:? The instructions are vague so I have no idea. 2) As C: and D: are both Physical drives, does it sound like C: should be partitioned out to create the E: drive or D:? Thanks for any help I can get. I am extremely stressed out under a massive workload right now, and these vague instructions are quite infuriating.

    Read the article

  • Linux laptop encryption

    - by kaerast
    What are my options for encrypting the /home directories of my Ubuntu laptops? They are currently setup without any encryption and some have /home as a separate partition whilst others don't. Most of these laptops are single-user standalone laptops which are out on the road a lot. Is ecryptfs and the encrypted Private directory good enough or are there better, more secure, options? If somebody got hold of the laptop, how easy would it be for them to gain access to the encrypted files? Similar questions for encrypted lvm, truecrypt and any other solution I may not be aware of.

    Read the article

  • When did my Mac's HD last sleep?

    - by flipdoubt
    Is there any app or log that says when my MacBook Pro's hard drive last went into sleep mode? I ask because each night when I close the MBP's lid without being plugged into a power source, the power light goes into its snooze rhythm but the battery is half-drained by the next morning. It certainly looks like it is asleep, but the power drain seems to indicate otherwise.

    Read the article

  • Cannot resize OS X partition

    - by joshhunt
    I am trying to resize my existing Mac OS Extended partition on my Macbook to install Windows 7 (using steps similar to these), but when ever I go to apply the changes, I get this error: Partition failed Partition failed with the error: The partition cannot be resized. Try reducing the amount of change in the size of the partition. The total capacity of the hard drive in question is 260GB, with the entirety being taken up by the OS X boot partition. There is I am aiming to shrink that partition down to 60GB. How can I fix this problem? I have been reducing the amount of change by 10GB each attempt, but it still is not working. I assume the problem is that there is not a large amount of continuous space on the device. Is there some way to can do a manual defrag that would rectify this problem?

    Read the article

  • does my machine configuration make sense?

    - by user1227914
    i couldn't think of a better place to ask this question, so here it goes. we're putting together a dedicated server for a website that will initially host the web server and the mysql database. as the website grows, we'll move the database to a different server and this machine will eventually only server the actual website. so the question is ...does my configuration look okay? it's the first time i'm building a server from scratch so i want to make sure i don't combine components that don't fit or something. things like ..do the drives i picked work for the hot swap ..etc. what do you guys think? am i good to go with this configuration? :) Chassis: Supermicro SuperServer 6016T-MTHF (6x DDR3 SDRAM - ECC DIMM 240-pin, 2x LGA1366 Socket, Power Provided: 600 Watt, 4 (free) x hot-swap - 3.5") CPU: Intel BX80614E5620 Xeon E5620 Processor - 4 Core, 2.40GHz, LGA 1366, 5.86GT/s QPI 12MB Cache, 64-Bit, 80W, HyperThreading Memory: Crucial CT51272BB1339 4GB PC10600 DDR3 Memory - 1333MHz, ECC, Registered, 1x4096MB (possibly 3 or 4 of them) Hard Drives: Western Digital WD2002FAEX Caviar Black Hard Drive - 2TB, 3.5", SATA 6Gbps, 7200 RPM, 64MB (possibly 2 or 3). thank you very much for any professional advice :)

    Read the article

  • WinXP: File Record Segment nnnn is unreadable?

    - by chris
    I'm pretty sure that the drive is toast, except for the fact that this error is only showing up on one partition (it's out of a Dell computer, and has a couple of Dell partitions, which boot and work fine.) I've already purchased another hard drive, and re-installed WinXP, but when I re-connect this drive and reboot, I'm getting thousands of these errors. Is there any chance of recovering any files off this? Should I prevent XP from trying to resolve the problems?

    Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >