Search Results

Search found 48997 results on 1960 pages for 'i ask questions for a reason'.

Page 59/1960 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

  • Is "DSLAM congestion" a legitimate reason for slow DSL?

    - by Jay Bazuzi
    My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

    Read the article

  • Why does outlook 2013, after initial setup, always fail to connect to an Exchange server/always ask for a password?

    - by jhstuckey
    After installing Outlook 2013 configuring it to connect to an exchange server (details about which, e.g., version, etc., I do not know how to provide) was stressful and the user used outlook without issue for a session. The next time outlook is started this error (Re. subject) occurs. The answer to this question solves the issue, or explains why it is happening (i.e., no one could provide a solution). Full size image: http://i.imgur.com/H2bVlyJ.png EDIT 5/18: To add more detail, a) after outlook 2013 was installed and configured (through the menu it prompts you with, add an account) it connected and was fine. It is only after outlook is closed and re-opened that it will not connect again to the server. This problem has been mentioned elsewhere, e.g., http://community.office365.com/en-us/forums/158/t/62832.aspx.

    Read the article

  • Random BSODs on Win7 boot. Can't find a valid reason.

    - by 0plus1
    Hi, I bought and assembled a new pc: ASUS m4a785td-v EVO AMD x4 620 OCZ Black Edition 2x 2gb WD 500gb sata Win7 Ultimate 64bit fresh install BSOD on boot. Formatted, reinstalled, BSOD on install. Ran memtest - no errors. Ran Win7 install in safe mode. Installed, random BSOD on win7 startup, even in safe mode. Updated BIOS. Ran the win7 memtest (no error), booted after some tries and ran Prime95 blend test for 12 hours straight with no errors at all! When the pc has booted, win7 runs as smooth as possible, I've been playing STALKER for 4 hours straight with not a single hiccup. Using Blue Screen View I can see that every BSOD involves: ntoskrnl.exe Here are the dumps Any help would be greatly appreciated, this thing is driving me crazy.

    Read the article

  • Is there any reason to install software as root as opposed to sudo installing software as a sudoer?

    - by Tchalvak
    I'm setting up a new server running Ubuntu Server Edition, and I'm not certain what the difference would be between installing most of the basic software as root, vs installing the basic software as an admin user using sudo apt-get install . For one thing, I'm not sure whether after installing the software as root, I'll need sudo access when running the software as a user (e.g. if I install git as root). On the other hand, if I install software as a user, I could conceive of it not being available to other users that I create in the future. What's the best practice here?

    Read the article

  • Proxy Error 502 "Reason: Error reading from remote server" with Apache 2.2.3 (Debian) mod_proxy and Jetty 6.1.18

    - by Martin
    Apache is receiving requests at port :80 and proxying them to Jetty at port :8080 The proxy server received an invalid response from an upstream server The proxy server could not handle the request GET /. My dilemma: Everything works fine normally (fast requests, few seconds or few tens of seconds long requests are processed ok). Problems occur when request processing takes long (few minutes?). If I issue request instead directly to Jetty at port :8080 the request is processed OK. So problem is likely to sit somewhere between Apache and Jetty where I am using mod_proxy. How to solve this? I have already tried some "tricks" related to KeepAlive settings, without luck. Here is my current configuration, any suggestions? #keepalive Off ## I have tried this, does not help #SetEnv force-proxy-request-1.0 1 ## I have tried this, does not help #SetEnv proxy-nokeepalive 1 ## I have tried this, does not help #SetEnv proxy-initial-not-pooled 1 ## I have tried this, does not help KeepAlive 20 ## I have tried this, does not help KeepAliveTimeout 600 ## I have tried this, does not help ProxyTimeout 600 ## I have tried this, does not help NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] ServerName www.mydomain.fi ServerAlias mydomain.fi mydomain.com mydomain www.mydomain.com ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPass / http://www.mydomain.fi:8080/ retry=1 acquire=3000 timeout=600 ProxyPassReverse / http://www.mydomain.fi:8080/ RewriteEngine On RewriteCond %{SERVER_NAME} !^www\.mydomain\.fi RewriteRule /(.*) http://www.mydomain.fi/$1 [redirect=301L] ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On </VirtualHost> Here is also the debug log from a failing request: 74.125.43.99 - - [29/Sep/2010:20:15:40 +0300] "GET /?wicket:bookmarkablePage=newWindow:com.mydomain.view.application.reports.SaveReportPage HTTP/1.1" 502 355 "https://www.mydomain.fi/?wicket:interface=:0:2:::" "Mozilla/5.0 (Windows; U; Windows NT 6.1; fi; rv:1.9.2.10) Gecko/20100914 Firefox/3.6.10" [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: error reading status line from remote server www.mydomain.fi, referer: https://www.mydomain.fi/?wicket:interface=:0:2::: [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: Error reading from remote server returned by /, referer: https://www.mydomain.fi/?wicket:interface=:0:2:::

    Read the article

  • Zabbix - Some of the monitored items dont get refreshd. how to find the reason?

    - by Niro
    I'm experiencing a strange issue with Zabbix monitoring a MySQL server. Most of the data from the server such as MySQL queries per second and MySQL uptime , Buffers memory etc. update nicely while some data like CPU iowait time (avg1) , Host local time ,MySQL number of threads and other items which were monitored in the past has last check time of about a week ago. I can't find any logic in this, for example Mysql number of threads and Mysql queries per second are obtained in a similar way so it does not make sense one of them is monitored and one is not. Please help- how can I fix this?

    Read the article

  • What is the main reason of adsl modem/routers dying ?

    - by ldigas
    The other day my home adsl modem/router (dwg 684t in this case) died. A guy from the telecom company came, brought another so no problem in day to day operation, but he also left this one. Now, I'm interested ... it didn't fall, it wasn't electrocuted ... but it just doesn't work. What could be the problem ? Can they be fixed ? Is it worth it (in which case I would have two which is always nice) ... What are the usual problems that occur with them ? In this case, I can connect to the router, I can see its settings, I just can't connect to the internet. With the new one everything works. Weird. Edit: Additional question: Can those things be fixed ? I mean, is it worth giving it to a local tinker for him to experiment on it ? I'm not looking for a definite opinion, just your personal advice ... (although in the end I think I'm gonna archive it in the "cylinder register")

    Read the article

  • Connection to Google, Yahoo, Bing, Ask, etc. compromised via all devices on my home network - How?

    - by jt0dd
    I'm a very computer savvy guy (although not very networking savvy), and I may still be wrong about this, but I think my home network may be compromised somehow. I'd like to know if it's possible for someone to have hijacked my network's connection to Google.com and other popular websites. Update: The issue seems to take effect with all popular websites. I can connect to small (non-popular) websites without issue, but Facebook, Google, Yahoo, and Bing cannot be accessed by any device on my home network. On all devices using my home network, I'm being shown http://www.google.com WARNING! Internet Explorer is currently out of date. Please update to continue. when I attempt to connect to google.com. I wouldn't be surprised by this at all if it were just the laptop. It's the fact that this is happening on all devices on my network that confuses me. Here's the screenshot from my iPhone, for reference. Can my home network be compromised? Is that even possible? How can something like this happen across all platforms on all devices in the same way? I wouldn't imagine every device / platform on the network would get the same virus. Should I assume that my network's security is totally compromised? Update: All mobile devices and laptops on my home network are experiencing the same alert when attempting to connect to google.com.

    Read the article

  • Use subpath internal proxy for subdomains, but redirect external clients if they ask for that subpath?

    - by HostileFork
    I have a VirtualHost that I'd like to have several subdomains on. (For the sake of clarity, let's say my domain is example.com and I'm just trying to get started by making foo.example.com work, and build from there.) The simplest way I found for a subdomain to work non-invasively with the framework I have was to proxy to a sub-path via mod_rewrite. Thus paths would appear in the client's URL bar as http://foo.example.com/(whatever) while they'd actually be served http://foo.example.com/foo/(whatever) under the hood. I've managed to do that inside my VirtualHost config file like this: ServerAlias *.example.com RewriteEngine on RewriteCond %{HTTP_HOST} ^foo\.example\.com [NC] # <--- RewriteCond %{REQUEST_URI} !^/foo/.*$ [NC] # AND is implicit with above RewriteRule ^/(.*)$ /foo/$1 [PT] (Note: It was surprisingly hard to find that particular working combination. Specifically, the [PT] seemed to be necessary on the RewriteRule. I could not get it to work with examples I saw elsewhere like [L] or trying just [P]. It would either not show anything or get in loops. Also some browsers seemed to cache the response pages for the bad loops once they got one... a page reload after fixing it wouldn't show it was working! Feedback welcome—in any case—if this part can be done better.) Now I'd like to make what http://foo.example.com/foo/(whatever) provides depend on who asked. If the request came from outside, I'd like the client to be permanently redirected by Apache so they get the URL http://foo.example.com/(whatever) in their browser. If it came internally from the mod_rewrite, I want the request to be handled by the web framework...which is unaware of subdomains. Is something like that possible?

    Read the article

  • Proxy Error 502 "Reason: Error reading from remote server" with Apache 2.2.3 (Debian) mod_proxy and Jetty 6.1.18

    - by Martin
    Apache is receiving requests at port :80 and proxying them to Jetty at port :8080 The proxy server received an invalid response from an upstream server The proxy server could not handle the request GET /. My dilemma: Everything works fine normally (fast requests, few seconds or few tens of seconds long requests are processed ok). Problems occur when request processing takes long (few minutes?). If I issue request instead directly to Jetty at port :8080 the request is processed OK. So problem is likely to sit somewhere between Apache and Jetty where I am using mod_proxy. How to solve this? I have already tried some "tricks" related to KeepAlive settings, without luck. Here is my current configuration, any suggestions? #keepalive Off ## I have tried this, does not help #SetEnv force-proxy-request-1.0 1 ## I have tried this, does not help #SetEnv proxy-nokeepalive 1 ## I have tried this, does not help #SetEnv proxy-initial-not-pooled 1 ## I have tried this, does not help KeepAlive 20 ## I have tried this, does not help KeepAliveTimeout 600 ## I have tried this, does not help ProxyTimeout 600 ## I have tried this, does not help NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] ServerName www.mydomain.fi ServerAlias mydomain.fi mydomain.com mydomain www.mydomain.com ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPass / http://www.mydomain.fi:8080/ retry=1 acquire=3000 timeout=600 ProxyPassReverse / http://www.mydomain.fi:8080/ RewriteEngine On RewriteCond %{SERVER_NAME} !^www\.mydomain\.fi RewriteRule /(.*) http://www.mydomain.fi/$1 [redirect=301L] ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On </VirtualHost> Here is also the debug log from a failing request: 74.125.43.99 - - [29/Sep/2010:20:15:40 +0300] "GET /?wicket:bookmarkablePage=newWindow:com.mydomain.view.application.reports.SaveReportPage HTTP/1.1" 502 355 "https://www.mydomain.fi/?wicket:interface=:0:2:::" "Mozilla/5.0 (Windows; U; Windows NT 6.1; fi; rv:1.9.2.10) Gecko/20100914 Firefox/3.6.10" [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: error reading status line from remote server www.mydomain.fi, referer: https://www.mydomain.fi/?wicket:interface=:0:2::: [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: Error reading from remote server returned by /, referer: https://www.mydomain.fi/?wicket:interface=:0:2:::

    Read the article

  • Is it possible to have zsh+keychain+tmux not ask for keys?

    - by Wayne Werner
    I'm using tmux and zsh, and I've recently been learning about ssh-agent and keychain. From the manpage for zsh, it says that it will source .zlogin only if the shell is, well, a login shell. Following advice I read, I stuck keychain --clear in my .zlogin, which worked perfectly. When I logged into the box I had to unlock my key. However, each time I create a new window in tmux, it clears/makes me re-add my key. This is a little annoying... but I can understand it if, in fact, each new tmux window is a login window. I haven't been able to find much help outside of the manpages on this topic. So is each new tmux window a login shell, or is there any way that I can make it not clear my keys only when I create a tmux window?

    Read the article

  • Why would my 15" MacBook Pro suddenly ask me to Hard Quit while I was in a browser?

    - by flathead27ford
    I was in Firefox looking at a search I had performed in eBay and all of a sudden, the screen grayed out starting from the top down. In the middle of the screen was a box with about 5 different languages saying I had to hard quit my computer. I tried other keys on my computer and nothing was working so I hard quit and restarted. Can anyone tell me why this happened? Cheers, Kyle

    Read the article

  • Is there a reason the partition tool GParted doesn't show a percentage finish number initially?

    - by Jian Lin
    I am using GParted more, and it seems to do a reliable work. I just wonder why if the tasks is to resize a 250GB partition to 190GB, and then create a new partition, the first 10, 15 minutes, there is only a blue bar moving left and right, but there won't be an indicator showing how many percent is done. Then after that 10 to 15 minutes, it does show 1:05:00 left to finish the job. Update: at first I thought there is no percentage or time remaining at all... but after waiting for 10, 15 mintues, it does show. I just wonder why it didn't show at first.

    Read the article

  • What is the reason for this DNSSEC validation failure of dnsviz.net?

    - by grifferz
    On trying to resolve dnsviz.net from a host using an Unbound resolver that is configured to use DNSSEC validation, the result is "no servers could be reached": $ dig -t soa dnsviz.net ; <<>> DiG 9.6-ESV-R4 <<>> -t soa dnsviz.net ;; global options: +cmd ;; connection timed out; no servers could be reached Nothing is logged by Unbound to suggest why this is the case. Here is the /etc/unbound/unbound.conf: server: verbosity: 1 interface: 192.168.0.8 interface: 127.0.0.1 interface: ::0 access-control: 0.0.0.0/0 refuse access-control: ::0/0 refuse access-control: 127.0.0.0/8 allow_snoop access-control: 192.168.0.0/16 allow_snoop chroot: "" auto-trust-anchor-file: "/etc/unbound/root.key" val-log-level: 2 python: remote-control: control-enable: yes If I add: module-config: "iterator" (thus disabling DNSSEC validation) then I am able to resolve this host normally. The domain and its DNSSEC check out fine according to http://dnscheck.iis.se/ so there must be something wrong with my resolver configuration. What is it and how do I go about debugging that?

    Read the article

  • What may the reason of slowness be (see details in message body)?

    - by Ivan
    I've got a really weird situation I'm beating to solve. A performance problem which looks really like an empty waiting sequence set in code (while it probably isn't so). I've got a pretty powerful dedicated server (10 GB RAM, eight Xeon cores, etc) running Ubuntu 10.04 with all the functionality services (except OpenVPN server used to provide secure access to clients) deployed in separate VirtualBox (vboxheadless) machines (one for the company e-mail server, one for web server and one for accounting/crm server (Firebird + proprietary app server working with Delphi-made clients)). CPU load (as "top" says) is almost always near zero. Host system RAM is close to 100% usage but not overloaded (as very little swapping gets used, and freed (by stopping one of VMs) memory doesn't get reused any quickly). Approximately 50% of guests RAM is used. iostat usually shows near zero %util. Network bandwidth seems to be underused. But the accounting/crm client (a Win32 Delphi application run on WinXP machines) software works hell-slow with this server (and works much better using an inside-LAN Windows server). I just can't imagine what can make it be slow if there are so plenty of CPU, RAM, HDD and bandwidth resources available on clients and on the server even in their hardest moments. Saying bandwidth is underused I not only know that clients and the server are connected to the Internet with a bigger channels than really used (which leaves the a chance they may have a bottleneck of a sort on the route between them), I've tested bandwidth between clients and the server by copying files among them.

    Read the article

  • With puppet, can you have the client ask to be a certain set of roles?

    - by Aitch
    I've recently got my puppetmaster and client up and running and have had the client correctly signed, then requested and applied simple changes, all good. I have a growing number of machines (100). They are not consistently named (historical reasons). They fall into a handful of categories (think of it like: dataserver_type1, dataserver_type2, webserver_type1, webserver_type2....). New instances of these types of machines are added weekly. I don't understand (yet) or cannot see how I can declare a "generic" node of (say) "dataserver_type1" that contains whatever modules it needs, and set something in the client puppet.conf that says "I am a dataserver_type1" without using the hostname/FQDN If I set the node name in the catalog as (say) "my-data-server-type1" - the certified hostname - it picks it up and works. I know you can use patterns for hostnames but as I said, my server names are not consistent, and I can't change them. This seems disingenuous to have to edit a file and manually add a node for each server, when they continue to grow. Edit: Digging deeper, it seems roles may be what I want. But there still seems to be an element whereby the master has contain a list of roles that a specific named server should do. Perhaps what I am asking is, how can a client say "I want to be this role", without the server having to be updated?

    Read the article

  • How do I ask screen to behave like a standard bash shell?

    - by thornomad
    Just learned about the screen command on linux - it is genius. I love it. However, the actual terminal/prompt in screen looks and behaves differently than my standard bash prompt. That is, the colors aren't the same, tab completion doesn't seem to work, etc. Is there a way I can tell screen to behave just like a normal (at least, normal as in what I am used to) bash prompt ?

    Read the article

  • What is the reason for: "Depends: libatk1.0-0 (>= 1.29.3) but 1.28.0-0ubuntu1 is to be installed"

    - by solomongaby
    I am trying to install Filezilla from this repository: https://launchpad.net/~yofel/+archive/ppa And after sudo apt-get update, I tried to install it but I get this error: Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: filezilla: Depends: libatk1.0-0 (>= 1.29.3) but 1.28.0-0ubuntu1 is to be installed Do you have any idea what is happening?

    Read the article

  • Is there any reason this cronjob would fail in cron, but not on the command line?

    - by Treffynnon
    I have written a little one liner that will email me when a list of files changes - I used sha512 to generate a list of hashes and then periodically check that those hashes still match. */5 * * * * /usr/bin/sha512sum --status -c /sha512.sumlist && echo "Success" > /dev/null || echo "Check robots.txt and index.html in /var/www as staging sites are now potentially exposed to the world and the damned googlebot" | /usr/bin/mail -s "Default staging server files have changed" [email protected] It works fine on the command line with: /usr/bin/sha512sum --status -c /sha512.sumlist && echo "Success" > /dev/null || echo "Check robots.txt and index.html in /var/www as staging sites are now potentially exposed to the world and the damned googlebot" | /usr/bin/mail -s "Default staging server files have changed" [email protected] As soon as I run it as a cronjob though it emails every time it runs with the failure message instead of only when the sha512sum check should fail. Is there something silly I have missed in a rush? I forgot to mention that I am running an Ubuntu machine.

    Read the article

  • What is the main reason for ADSL modem/routers dying?

    - by ldigas
    The other day my home ADSL modem/router (dwg 684t in this case) died. A guy from the telecom company came to my place and brought another one, but he also left this one. Now, I'm interested - it didn't fall, it wasn't electrocuted - but it just doesn't work. What could be the problem? Can it be fixed? Is it worth it (in which case I would have two which is always nice)? I'm not looking for a definite opinion, just your personal advice ... (although in the end I think I'm going to archive it in the "cylinder register") What are the usual problems that occur with them? In this case, I can connect to the router, I can see its settings, I just can't connect to the Internet. With the new one everything works. Weird.

    Read the article

  • How do I ask screen to behave like a standard bash shell?

    - by thornomad
    Just learned about the screen command on linux - it is genius. I love it. However, the actual terminal/prompt in screen looks and behaves differently than my standard bash prompt. That is, the colors aren't the same, tab completion doesn't seem to work, etc. Is there a way I can tell screen to behave just like a normal (at least, normal as in what I am used to) bash prompt ? Additional Information I am connecting via ssh from a Mac (Terminal) to a headless linux box (Ubuntu). After logging in, I have TERM=xterm-color and when I run screen I have TERM=screen. Am going to try the suggestions below to see if I can change the $TERM value first.

    Read the article

  • How can I ask for a new dhcp lease on windows 7?

    - by Pat
    In windows7 how do I request a new dhcp lease ? What I need in the equivalent of the button "repair" on windows XP. The button "diagnose" seems to do a few things but not request a new dhcp lease if one is already available. Disabling and re-enabling the card does the trick but messes up any program capturing traffic on the interface.

    Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >