Search Results

Search found 20785 results on 832 pages for 'idea'.

Page 592/832 | < Previous Page | 588 589 590 591 592 593 594 595 596 597 598 599  | Next Page >

• When machine is turned on, only the fan runs

  - by Gopal

  Hi, I have an issue slightly similar to this one posted here, http://superuser.com/questions/127016/troubleshooting-monitor-never-turns-on-system-fans-running-dvd-rom-does-not-op My configuration is as follows: EPOX 9NPA+ Ultra motherboard AMD Athlon 64 CPU Corsair 2 x 1GB PC3200 DDR RAM 1 DVD RW drive and 1 CD ROM Drive SATA 250 GB Hard drive 400W Power supply EVGA 256MB graphics card I have had this configuration for about four years. Last month, I started having issues in starting the machine. It wouldn't start when I press the ON button in the front of the case. So I used to pull out the power cord and plug it back in and then switch on in the front, and it used to work fine. And then one fine day, when I plugged in the power cord at the back, even without switching on the power-on button at the front, I saw that the fan at the back was running. So I opened the system. Then I could see that all the fans inside were running. I replaced the power supply. No luck there. Then I replaced the CMOS battery. Again nothing improved. Even when I removed all the cards and memory, I still get one short beep. That's it. Any idea how to proceed on this? Anything else could be checked? I want to confirm if this is a motherboard failure, before proceeding to replace it.

  Read the article

• Asus K55VM usb 3.0 issue

  - by user2141481

  Good day superusers! I own the above laptop and I found out that there are some unknown and unusual issues with usb 3.0 ports. I haven't noticed anything strange until now. I got a new toshiba usb 3.0 external hdd and when I try to copy larger amount of data from my disk to the external hdd, the OS(windows 7) randomly starts ignoring the external hdd. It doesn't shut it down, it kinda just stops responding but the light on the hdd is still lit. I get an error that the files cannot be copied. I have reinstalled windows 7, installed all drivers(including intel chipset drivers of course) and the issue is still present. It acts normal when copying small amount of data. Also, I heard that some intel chipsets have an issue with usb, something about the connectors not transferring power when the usb device enters some kind of "low power mode" causing the device to stop responding and you need to plug it out and in again. But the thing is, my Intel® Chief River Chipset HM76 is not on the list of affected hardware(not ENTIRELY sure though). If anyone has any idea of what the problem to this might be, I'd be greatful. Edit: The hdd works perfectly fine even for large amounts of data if plugged in the usb 2.0 port!

  Read the article

• Motion - takes snapshot without motion detected

  - by Emmanuel Brunet

  I've been installed the standard motion 3.2.12 package on debian 7.5. I would like to get snapshot ONLY when motion is detected, but it still saves a picture every second without any activity in front of the camera. I'm using a TENVIS JPT3815W IP camera motion.conf here is my configuration file setup_mode off target_dir /media/videos/log/webcam netcam_url http://webcam/snapshot.cgi netcam_tolerant_check on netcam_userpass admin:alpha1237 # Output frames at 1 fps when no motion is detected and increase to the # rate given by webcam_maxrate when motion is detected (default: off) webcam_motion off output_all off # detection settings 1-255 default 32 noise_level 50 # Maximum framerate for webcam streams (default: 1) webcam_maxrate 25 pre_capture 0 framerate 25 gap 30 locate on mail [email protected] text_right "FRONT CAMERA %Y/%m/%d - %T" text_double on ffmpeg_cap_new on ffmpeg_cap_motion on ffmpeg_video_codec mpeg4 output_motion off snapshot_interval 0 # Quality of the jpeg (in percent) images produced (default: 50) quality 90 # Restrict webcam connections to localhost only (default: on) webcam_localhost off # Limits the number of images per connection (default: 0 = unlimited) # Number can be defined by multiplying actual webcam rate by desired number of seconds # Actual webcam rate is the smallest of the numbers framerate and webcam_maxrate webcam_limit 0 Issue when I start motion images are stored in /media/videos/log/webcam nearly every second. I hjust want to get images when a motion is detected and the according video clip Any idea where the configuration fails ?

  Read the article

• Debian, How to convert filesystem from ISO-8859-1 into UTF-8?

  - by Johan

  I have a old pc that is running Debian stable, that is in need of a upgrade. The problem is that it is using latin1 (ISO-8859-1) for everything, and since the rest of the world has moved to UTF-8 I plan to convert this computer as well. And for this question I will focus in on the files that are served with Samba, and some has some latin1 characters in the filenames (like åäö). Now my plan is to move all data of this old computer onto and a brand new one that is running Debian stable (but with UTF-8). Does anybody have a good idea? Thanks Johan Note: later I plan to use iconv to convert the content of some files with something like this: iconv --from-code=ISO-8859-1 --to-code=UTF-8 iso.txt > utf.txt However I don't know of a good way to convert the filesystem it self. Note: Normally I usaly just scp from one computer to the next, but then I end up with latin1 characters in the utf-8 filesystem... Update: Did a small test round with a hand full of files (with funny chars) in the filenames, and that seemed like it could work. convmv -r -f ISO-8859-1 -t UTF-8 * So it was only to execute with the --notest convmv -r -f ISO-8859-1 -t UTF-8 --notest * Nothing more to it.

  Read the article

• DNS failover in a two datacenter scenario

  - by wanson

  I'm trying to implement a low-cost solution for website high availability. I'm looking for the downsides of the following scenario: I have two servers with the same configuration, content, mysql replication (dual-master). They are in different datacenters - let's call them serverA and serverB. Users use serverA - serverB is more like a backup. Now, I want to use DNS failover, to switch users from serverA to serverB when serverA goes down. My idea is that I setup DNS servers (bind/powerdns) on serverA and serverB - let's call them ns1.website.com and ns2.website.com (assuming I own website.com). Then I configure my domain to use them as its nameservers. Both DNS servers will return serverA IP as my website's IP. If serverA goes down I can (either manually or automatically from serverB) change configuration of serverB's DNS, to return IP of serverB as website's IP. Of course the TTL will be low, as it's supposed to be in DNS failovers. I know that it may take some time to switch to serverB (DNS ttl, time to detect serverA failure, serverB DNS reconfiguration etc), and that some small part of users won't use serverB anyway. And I'm OK with that. But what are other downsides of such an approach? An alternative scenario is that ns1.website.com will return serverA IP as website's IP, and ns2.website.com will return serverB IP as website's IP. But AFAIK clients not always use primary nameserver and sometimes would use secondary one. So some small part of users would use serverB instead of serverA which is not quite what I'd like. Can you confirm that DNS clients behave like that and can you tell what percentage of clients would possibly use serverB instead of serverA (statistically)? This one also has the downside that when serverA goes back up, it will be automatically used as website's primary server, which is also a bad situation (cold cache, mysql replication could fail in the meantime etc). So I'm adding it only as a theoretical alternative. I was thinking about using some professional DNS failover companies but they charge for the number of DNS requests and the fees are very high (why?)

  Read the article

• Setup Entourage for Exchange via HTTP communication

  - by Johandk

  Our ISP set up a hosted exchange server for all our mail. I've setup all our Outlook users with no problems. We have two people using Mac OSX Leopard and Entourage. Entourage has the option of adding an Exchange account, but I have no idea how to tell it to connect to exchange via HTTP. Heres an excerpt from the client setup docs the hosting company sent me for Outlook: 1 .Go to control panel 2. Select ‘Mail’ 3. Select ‘Email accounts’ Under the E-mail tab select ‘New’ Select ‘Manually configure server settings......’ - click next Select ‘Microsoft Exchange’ – click next Complete details as below with Microsoft Exchange Server as: [server address] Do not select ‘Check Name’. Instead select ‘More Settings’. Go to the Connection tab, and select the bottom option ‘Connect to Microsoft Exchange using HTTP’. And then select the ‘Exchange Proxy Settings’ button. Enter Proxy server for Exchange Check Only connect to proxy servers that have this principal name in their certificate, Enter msstd:[servername] Proxy Authentication - select Basic Authentication Select OK, and again, so that you return to the main screen. Now select ‘Check Name’. Enter Username and Password: The username should now be the full name and underlined. If so select next, and then finish. Next time you open Outlook, enter username and password Any help GREATLY appreciated.

  Read the article

• No apparent reason for high load average

  - by Oz.

  We have several web servers running on Amazon (ec2) c1.xlarge, over Amazon AMI. The servers are duplicates of each other, running the exact same hardware and software. Each server spec is: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge A couple of weeks ago we have run a yum upgrade on one of the servers. Starting on this upgrade the upgraded server started showing a high load average. Needless to say, we did not update the other servers and we can not do so until we understand the reason for this behavior. The strange thing is that when we compare the servers using top or iostat, we can not find the reason for the high load. Note that we have moved traffic from the "problematic" server to the others, which have made the "problematic" server less crowded in terms of requests, and still his load is higher. Do you have any idea what could it be, or where else can we check? Many thanks for the help! Oz. # # proper server # w command # 00:42:26 up 2 days, 19:54, 2 users, load average: 0.41, 0.48, 0.49 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT pts/1 82.80.137.29 00:28 14:05 0.01s 0.01s -bash pts/2 82.80.137.29 00:38 0.00s 0.02s 0.00s w # # proper server # iostat command # Linux 3.2.12-3.2.4.amzn1.x86_64 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 9.03 0.02 4.26 0.17 0.13 86.39 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 1.63 1.50 55.00 367236 13444008 xvdfp1 4.41 45.93 70.48 11227226 17228552 xvdfp2 2.61 2.01 59.81 491890 14620104 xvdfp3 8.16 14.47 94.23 3536522 23034376 xvdfp4 0.98 0.79 45.86 192818 11209784 # # problematic server # w command # 00:43:26 up 2 days, 21:52, 2 users, load average: 1.35, 1.10, 1.17 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT pts/0 82.80.137.29 00:28 15:04 0.02s 0.02s -bash pts/1 82.80.137.29 00:38 0.00s 0.05s 0.00s w # # problematic server # iostat command # Linux 3.2.20-1.29.6.amzn1.x86_64 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 7.97 0.04 3.43 0.19 0.07 88.30 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 2.10 1.49 76.54 374660 19253592 xvdfp1 5.64 40.98 85.92 10308946 21612112 xvdfp2 3.97 4.32 93.18 1087090 23439488 xvdfp3 10.87 30.30 115.14 7622474 28961720 xvdfp4 1.12 0.28 65.54 71034 16487112

  Read the article

• Are there any open source reseller packages?

  - by Tom Wright

  My department has just been given the right/responsibility to manage our own VPS. The idea being that the bureaucracy will be less for the many small web projects we run. Since each project will be managed by a different team, I was planning on approaching a shared hosting model. Are there any free pieces of software that would help automate the provision of resources each time a team request a new project? Most of the projects have identical requirements - basically LAMP - so it would be these resources that I would want provisioning (and de-provisioning, if that is a word) automatically. Ideally, there would also be a way to hook it into our LDAP authentication backend too, though I could probably make this sort of modification if necessary. Since we won't be charging our "client" however, we won't need the ability to generate invoices, handle payments, etc. etc. EDIT: Sample workflow Login authenticated against LDAP Username checked against admin group (not on central LDAP) Click 'new project' and enter project name User created on VPS with project name as username Apache virtual host created and subdomain (using project name) allocated FTP & MySQL users created

  Read the article

• Ubuntu 12.04 suddenly cannot connect to WPA2/WPA Personal protected connection. Windows 7 can

  - by d4ryl3

  I have a laptop with Windows 7 and Ubuntu 12.04. I have a Cisco E1200 and when I set it up, it created 2 SSIDs. Let's name them: MyConnection (WPA/WPA2 personal), and MyConnection-Guest (no authentication, guest password entered via web browser). I had no problem connecting to MyConnection before, either in Windows 7 and Ubuntu. But now, I can't access MyConnection on Ubuntu. It just says "connecting..." then disconnects after a while. But I'm able to access the internet (on Ubuntu) when I connect to MyConnection-Guest. MAC filtering is off (even if it's on its MAC address is in the white list). Any idea why I'm unable to connect to MyConnection in Ubuntu? Thanks. Update: My Ubuntu installation can connect to ANY WiFi connection (WPA/WEP/no auth), except for MyConnection. Update2: This is what "The not so easy way" returned: Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant.conf' Priority group 0 id=0 ssid='MyConnection' id=1 ssid='MyConnection' id=2 ssid='MyConnection' id=3 ssid='MyConnection' WEXT: cfg80211-based driver detected SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf flags 0x0 netlink: Operstate: linkmode=1, operstate=5 Own MAC address: xx:xx:xx:xx:xx:xx wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_countermeasures RSN: flushing PMKID list in the driver Setting scan request: 0 sec 100000 usec WPS: UUID based on MAC address - hexdump(len=16): 16 3b d8 47 9e 24 50 89 96 16 6d 66 35 f3 58 37 EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: Supplicant port status: Unauthorized EAPOL: Supplicant port status: Unauthorized Added interface eth1

  Read the article

• How to debug silent hang on shutdown of Solaris 10?

  - by jblaine

  We're experiencing a mysterious hang on shutdown of a newly-imaged Oracle/Sun Solaris 10 SPARC box. It is repeatable (in the same spot ... from what we can tell). We let it try to work itself out multiple times for 5-10 minutes and it never progressed. I've never seen this happen before. The last thing displayed on the console is that syslogd was sent signal 15. Prior to us disabling snmpdx on the box, the last thing on the console was that snmpdx was sent signal 15 (after syslogd was sent signal 15). While very rare to find, in Solaris days past, I'd have a better idea from experience where the problem might be, and could then narrow things down further with silly (but effective) debugging echo statments in /etc/*.d scripts. With SMF in the picture, I'm not really quite sure where to start. We forced a crash dump via sync at the {ok} prompt for later analysis, and then let the box come up because it's a production server and our scheduled outage window was closing. /var/adm/messages shows nothing of use. How would you debug this situation? mdb ps of the savecore shows the following processes were running at hang time (afsd is the OpenAFS client and that many are expected): > > ::ps S PID PPID PGID SID UID FLAGS ADDR NAME R 0 0 0 0 0 0x00000001 00000000018387c0 sched R 108 0 0 0 0 0x00020001 00000600110fe010 zpool-silmaril-p R 3 0 0 0 0 0x00020001 0000060010b29848 fsflush R 2 0 0 0 0 0x00020001 0000060010b2a468 pageout R 1 0 0 0 0 0x4a024000 0000060010b2b088 init R 1327 1 1327 329 0 0x4a024002 00000600176ab0c0 reboot R 747 1 7 7 0 0x42020001 0000060017f9d0e0 afsd R 749 1 7 7 0 0x42020001 00000600180104d0 afsd R 752 1 7 7 0 0x42020001 0000060017cb44b8 afsd R 754 1 7 7 0 0x42020001 0000060017fc8068 afsd R 756 1 7 7 0 0x42020001 0000060017fcb0e8 afsd R 760 1 7 7 0 0x42020001 00000600177f4048 afsd R 762 1 7 7 0 0x42020001 000006001800f8b0 afsd R 764 1 7 7 0 0x42020001 000006001800ec90 afsd R 378 1 378 378 0 0x42020000 0000060013aee480 inetd R 7 1 7 7 0 0x42020000 0000060010b28008 svc.startd R 329 7 329 329 0 0x4a024000 00000600110ff850 sh Z 317 7 317 317 0 0x4a014002 0000060013b3a490 sac

  Read the article

• iperf max udp multicast performance peaking at 10Mbit/s?

  - by Tom Frey

  I'm trying to test UDP multicast throughput via iperf but it seems like it's not sending more than 10Mbit/s from my dev machine: C:\> iperf -c 224.0.166.111 -u -T 1 -t 100 -i 1 -b 1000000000 ------------------------------------------------------------ Client connecting to 224.0.166.111, UDP port 5001 Sending 1470 byte datagrams Setting multicast TTL to 1 UDP buffer size: 8.00 KByte (default) ------------------------------------------------------------ [156] local 192.168.1.99 port 49693 connected with 224.0.166.111 port 5001 [ ID] Interval Transfer Bandwidth [156] 0.0- 1.0 sec 1.22 MBytes 10.2 Mbits/sec [156] 1.0- 2.0 sec 1.14 MBytes 9.57 Mbits/sec [156] 2.0- 3.0 sec 1.14 MBytes 9.55 Mbits/sec [156] 3.0- 4.0 sec 1.14 MBytes 9.56 Mbits/sec [156] 4.0- 5.0 sec 1.14 MBytes 9.56 Mbits/sec [156] 5.0- 6.0 sec 1.15 MBytes 9.62 Mbits/sec [156] 6.0- 7.0 sec 1.14 MBytes 9.53 Mbits/sec When I run it on another server, I'm getting ~80Mbit/s which is quite a bit better but still not anywhere near the 1Gbps limits that I should be getting? C:\> iperf -c 224.0.166.111 -u -T 1 -t 100 -i 1 -b 1000000000 ------------------------------------------------------------ Client connecting to 224.0.166.111, UDP port 5001 Sending 1470 byte datagrams Setting multicast TTL to 1 UDP buffer size: 8.00 KByte (default) ------------------------------------------------------------ [180] local 10.0.101.102 port 51559 connected with 224.0.166.111 port 5001 [ ID] Interval Transfer Bandwidth [180] 0.0- 1.0 sec 8.60 MBytes 72.1 Mbits/sec [180] 1.0- 2.0 sec 8.73 MBytes 73.2 Mbits/sec [180] 2.0- 3.0 sec 8.76 MBytes 73.5 Mbits/sec [180] 3.0- 4.0 sec 9.58 MBytes 80.3 Mbits/sec [180] 4.0- 5.0 sec 9.95 MBytes 83.4 Mbits/sec [180] 5.0- 6.0 sec 10.5 MBytes 87.9 Mbits/sec [180] 6.0- 7.0 sec 10.9 MBytes 91.1 Mbits/sec [180] 7.0- 8.0 sec 11.2 MBytes 94.0 Mbits/sec Anybody has any idea why this is not achieving close to link limits (1Gbps)? Thanks, Tom

  Read the article

• Windows 2012 RDS Temporary profile for Administrator

  - by Fabio

  I've configured a Windows 2012 RDS Farm with two virtual servers (VMWare - each one on a different ESX server). Both servers have Licensing, Web Access, Gateway, Connection Broker and Session Host roles. High Availability is set up and it works fine. Remote Apps are working and even Windows XP clients have access to the web interface. User profile path is \vmfiles1\UserProfileDisks\App\ and almost everyone has full right access to it. The problem I have is that I would like to be able to access both servers at the same time with the Administrator account (console), but each time I try, the second server that I logon to give me access with a temporary profile. I tried to enable/disable multiple sessions per user and forced Admin logoff with the GPO but nothing changed. Another thing is that the server pool is not saved, so each time I restart the RDS server or I logoff from it, I have to add a server in the server manager. Do you have any idea? Sorry if my english is not perfect.

  Read the article

• Setting Up My Home Network

  - by Skizz

  I currently have five PCs at home, three running WinXP and two running Ubuntu. They are set up like this: ISP ----- Modem ---- Switch ---- Ubuntu1 -- B&W Printer | |--WinXP1 | |--WinXP2 Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) The Ubuntu1 machine is set up as a PDC using Samba and runs fetchmail, procmail, dovecot to get my e-mail and allow me to access the e-mail via imap so I can read the e-mail on any PC. I'd like to set up the network like this: ISP ----- Modem ---- Ubuntu1 ---- Switch ------WinXP1 | | |--WinXP2 B&W Printer Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) My questions are: How to configure Ubuntu1 to act as a firewall. How to configure Ubuntu1 to provide a consistant user authentication across the network, at the moment Samba provides roaming profiles for the XP machines but the Ubuntu2 machine has it's own user lists. I'd like to have a single authentication for both XP machines and linux machines so that users added to the server list will propagate to all PCs (i.e. new users can log on using any PC without modifying any of the client PCs). How to configure a linux client (Ubuntu2 above) to access files on the server (Ubuntu1), some of which are in user specific folders, effectively sharing /home/{user} per user (read and write access) and stuff like /home/media/photos with read access for everyone and limited write access. How to configure the XP machines (if it is different from a the Samba method). How to set up e-mail filtering. I'd like to have a whitelist/blacklist system for incoming e-mails for some of the e-mail accounts (mainly, my kids' accounts) with filtered e-mails being put into quaranteen until a sysadmin either adds the sender to a blacklist or whitelist. OK, that's a lot of stuff. For now, I don't want config files*, rather, what services / applications to use and how they interact. For example, LDAP could be used for authentication but what else would be useful to make the administration of the LDAP easier. Once I have a general idea for the overall configuration, I can ask other questions about the specifics. Skizz I have looked around for information, but most answers are usually in the form of abstract config files and lists of packages to install.

  Read the article

• Designing a software based load balancer

  - by Kishore pandey

  Hello to all Server fault users, I am new to this website but have constantly been using the mother website, stackover flow. Well to begin with, i would like to design a load balancer for the organization i am working for. As i am very new to this whole, idea about load balancing and networks. I am finding it very difficult to start my project. I did a lot of research on already existing load balancer and found some(HAPROXY,NGINX) that could solve my problems, but the point is, I am still in a dilemma if they could answer the following requirements of mine: The client and server in my architecture are distributed. The load balancer should take care of the firewall. LB server should balance the load among all servers present in WWW cloud. The LB server should have some sort of configuration file, with the help of which it is possible to configure the servers. Heart beat: With the help of which it would be possible to check if any server is down, if any server is down the request should be passed to some other server. Various load balancing algorithms of the incoming requests. Easy error handling. It should be fairly possible to prioritize the incoming requests. Is there any already available load balncer solution on the market that could satisfy these requirements? If not is there any base code available with the help of which i could develop my own load balncer. If not where should i start from scratch? I am practically new to everything. Any help from a load balancer expert is very much appreciated. Thanx a ton in advance. Cheers and regards. Kishore

  Read the article

• Triple monitor setting in Linux with USB-HDMI adapter

  - by Oscar Carballal

  I'm trying to set up a triple monitor desktop at my office using Fedora 17, but it seems impossible, let me explain the setting: Laptop ASUS K53SD with 2 graphic cards, Intel and nVidia (Screen controled by Intel card) 24" Full HD monitor connected to the HDMI output (controlled by Intel card) 23" Full HD monitor connected to an USB-HDMI adapter (via framebuffer in /dev/fb2, apparently) VGA output (not used) controlled by nVidia card First of all, the USB-HDMI adapter works perfectly, it gives me a green screen (which means the communication is OK) and I can make it work if I set up a single monitor setting via framebuffer in Xorg. Here I leave the page where I got the instructions: http://plugable.com/2011/12/23/usb-graphics-and-linux Now I'm trying to set up the the two main monitors (laptop and 24") with the intel driver and the 23" with the framebuffer, but the most succesful configuration I get is the two main monitors working and the third disconnected. Do you have any idea what can I do to make this work? Here I leave my xRandr output and my Xorg conf: -> xrandr Screen 0: minimum 320 x 200, current 3286 x 1080, maximum 8192 x 8192 LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA2 disconnected (normal left inverted right x axis y axis) HDMI1 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 531mm x 299mm 1920x1080 60.0*+ 50.0 25.0 30.0 1680x1050 59.9 1680x945 60.0 1400x1050 74.9 59.9 1600x900 60.0 1280x1024 75.0 60.0 1440x900 75.0 59.9 1280x960 60.0 1366x768 60.0 1360x768 60.0 1280x800 74.9 59.9 1152x864 75.0 1280x768 74.9 60.0 1280x720 50.0 60.0 1440x576 25.0 1024x768 75.1 70.1 60.0 1440x480 30.0 1024x576 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 720x576 50.0 848x480 60.0 720x480 59.9 640x480 72.8 75.0 66.7 60.0 59.9 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) 1920x1080_60.00 60.0 The Xorg file: # Xorg configuration file for using a tri-head display Section "ServerLayout" Identifier "Layout0" Screen 0 "HDMI" 0 0 Screen 1 "USB" RightOf "HDMI" Option "Xinerama" "on" EndSection ########### MONITORS ################ Section "Monitor" Identifier "USB1" VendorName "Unknown" ModelName "Acer 24as" Option "DPMS" EndSection Section "Monitor" Identifier "HDMI1" VendorName "Unknown" ModelName "Acer 23SH" Option "DPMS" EndSection ########### DEVICES ################## Section "Device" Identifier "Device 0" Driver "intel" BoardName "GeForce" BusID "PCI:0:02:0" Screen 0 EndSection Section "Device" Identifier "USB Device 0" driver "fbdev" Option "fbdev" "/dev/fb2" Option "ShadowFB" "off" EndSection ############## SCREENS ###################### Section "Screen" Identifier "HDMI" Device "Device 0" Monitor "HDMI1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "USB" Device "USB Device 0" Monitor "USB1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• Why does this rsnapshot exclude not work?

  - by bstpierre

  Rsnapshot passes excludes directly to rsync, but rsync's behavior appears inconsistent. I've simplified my rsnapshot backup test to the following directory tree (this tree will be backed up): gorilla:~# find /tmp/snaptest -exec file {} \; /tmp/snaptest: directory /tmp/snaptest/SKIPTHIS: directory /tmp/snaptest/SKIPTHIS/xyz: directory /tmp/snaptest/SKIPTHIS/xyz/testing: ASCII text /tmp/snaptest/SKIPTHIS/bar: ASCII text /tmp/snaptest/SKIPTHIS/foo: ASCII text /tmp/snaptest/SKIPTHIS.txt: ASCII text My config file: config_version 1.2 snapshot_root /tmp/backup-media no_create_root 1 cmd_cp /bin/cp cmd_rm /bin/rm cmd_rsync /usr/bin/rsync cmd_ssh /usr/bin/ssh cmd_logger /usr/bin/logger cmd_du /usr/bin/du interval hourly 6 interval daily 7 interval weekly 4 interval monthly 3 verbose 3 loglevel 3 logfile /media/maxtor-one-touch/rsnapshot.log lockfile /media/maxtor-one-touch/backups/.rsnapshot.pid rsync_short_args -a rsync_long_args --delete --numeric-ids --relative --delete-excluded exclude "SKIPTHIS/**" link_dest 1 backup /tmp/snaptest snaptest The result: gorilla:~# rsnapshot -c /tmp/snaptest.conf hourly echo 12638 > /media/maxtor-one-touch/backups/.rsnapshot.pid mkdir -m 0755 -p /tmp/backup-media/hourly.0/ /usr/bin/rsync -a --delete --numeric-ids --relative --delete-excluded \ --exclude="SKIPTHIS/**" /tmp/snaptest \ /tmp/backup-media/hourly.0/snaptest touch /tmp/backup-media/hourly.0/ rm -f /media/maxtor-one-touch/backups/.rsnapshot.pid gorilla:~# find /tmp/backup-media/ -exec file {} \; /tmp/backup-media/: directory /tmp/backup-media/hourly.0: directory /tmp/backup-media/hourly.0/snaptest: directory /tmp/backup-media/hourly.0/snaptest/tmp: sticky directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest: directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS: directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/xyz: directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/xyz/testing: ASCII text /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/bar: ASCII text /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/foo: ASCII text /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS.txt: ASCII text My confusion stems from the fact that if I copy-paste the rsync command echoed by rsnapshot, the SKIPTHIS directory is excluded! (I've tested with various other SKIPTHIS patterns with the same results.) Any idea what's going on?

  Read the article

• Command line scripts to restore the 4 system databases of MS SQL Server 2008

  - by ciscokid

  Hi there, can someone give me some advice on how to restore the 4 system databases (master, msdb, model, tempdb) of a sql server 2008 please? I've already done some testing myself (on restoring the master database) with the following commad line script as a result: ::set variables set dbname=master set dbdirectory=C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA title Restoring %dbname% database net stop mssqlserver cd C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\Binn sqlservr -m sqlcmd -Slocalhost -E -Q "restore database master from disk='c:\master.bak' WITH REPLACE" net start mssqlserver pause After the execution of the 'sqlservr -m' command (used to start the server instance in single-user mode, which is only necessary when restoring the MASTER database), the script stops. So in order to execute the last 2 commands I need to separate the script into 2 smaller scripts, and run them one after the other. Does anyone has an idea on how I can merge them into one single script that runs completely without any interruption? I also want to restore the other 3 system databases using command line scripts like this one. Can someone please advice me how I need to go on? I've already noticed that restoring the temdb is not so easy, but there has to be a way... Looking forward to your advice!

  Read the article

• SVN, Samba and Symbolic Links. How to get them all to play together?

  - by Camsoft

  I've got a website project under version control that relies on files from an unversioned directory on the same server via Symbolic Links. I'm currently storing the symbolic links in the repository. The idea is that if someone checks out a working copy on to the same server they can edit and test the working copy of the project before committing it back to the repository. When they checkout their working copy it successfully sets up the symlinks so that the entire site works when testing. The users that work on the project are Windows users, so I've set a samba shares on the server and then mapped them to network drives in Windows. People can edit their working copies directly on the server via network shares and then test them in the web browser before committing their changes back to the repository via TortoiseSVN. The Problem The problem I have is that Samba resolves the symlinks as expected but when a user tries to commit their changes back to the repository, TortoiseSVN thinks the linked files are part of the project and tries to commit the target files to the repository and not the symlinks themselves. I tried turning off symlink support in samba which means that the linked files cannot be resolved as I don't really want people to have access to the linked files nor do I want to import the linked files in the repository. The problem with this is that I get Can't stat '\webserver\projects\working\project\symlinked_file.php'. Access is denied Apart from the symlink problem everything else works 100% perfectly. Users can either checkout website projects to their machine and work on them (but can't test) or checkout them out to their space on the dev web server and work on them and fully test. So I don't want to change the workflow process, I just need a solution to the symbolic link issue. Many thanks. Originally posted on StackOverflow: http://stackoverflow.com/questions/2400917/svn-samba-and-symbolic-links-how-to-get-them-all-to-play-together

  Read the article

• AWS VPC ELB vs. Custom Load Balancing

  - by CP510

  So I'm wondering if this is a good idea. I have a Amazon AWS VPC setup with a public and private subnets. So I all ready get the Internet Gateway and NAT. I was going to setup all my web servers (Apache2 isntances) and DB servers in the private subnet and use a Load Balancer/Reverse Proxy to pick up requests and send them into the private subnets cluster of servers. My question then, is Amazons ELB's a good use for these, or is it better to setup my own custom instance to handle the public requests and run them through the NAT using nginx or pound? I like the second option just for the sake of having a instance I can log into and check. As well as taking advantage of caching and fail2ban ddos prevention, as well as possibly using fail safes to redirect traffic. But I have no experience with their ELB's, so I thought I'd ask your opinions. Also, if you guys have an opinion on this as well, would using the second option allow me to only have 1 public IP address and be able to route SSH connections through port numbers to respective instances? Thanks in advance!

  Read the article

• Controller Error: Do I need to worry?

  - by Kryten

  I have a HP Pavillion dv5224ea Laptop with Windows 7 on it. Recently I discovered a Error in Event Viewer: The driver detected a controller error on \Device\Ide\IdePort1. (more details): - System - Provider [ Name] atapi - EventID 11 [ Qualifiers] 49156 Level 2 Task 0 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2010-03-07T12:43:07.090197600Z EventRecordID 30198 Channel System Computer Alistair-Win7 Security - EventData \Device\Ide\IdePort1 0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00100000 00000001 00000000 C004000B 0008: 00000002 C0000185 00000000 00000000 0010: 00000000 00000000 00000000 00000000 0018: 00000000 00001004 In Bytes 0000: 00 00 10 00 01 00 00 00 ........ 0008: 00 00 00 00 0B 00 04 C0 .......À 0010: 02 00 00 00 85 01 00 C0 ......À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 00 00 00 00 04 10 00 00 ........ Event Viewer is recording A LOT of these errors (sometimes 13, one after the other!). Do I need to worry? What does this error mean? What device could "\Device\Ide\IdePort1" be? What is a ATAPI Error? Do I need to re-install Windows? I generally find the occurs when I try to backup my machine (using Windows Backup) or when using a program that uses Volume Shadow Copy. I have run "sfc", no problems. There are no Device Errors in Device Manager. I have also run "vssadmin list writers", no problems. Whats going on??? Would it be a good idea to re-install Windows 7?

  Read the article

• Can't install xclip on Ubuntu 10.10

  - by wildster

  I'm trying to load an SSH key to Github from a new machine and this command is not working: sudo apt-get install xclip Reading package lists... Done Building dependency tree Reading state information... Done Package xclip is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package xclip has no installation candidate when I try: sudo aptitude install xclip Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done No candidate version found for xclip No candidate version found for xclip The following partially installed packages will be configured: synaptics-dkms 0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0B of archives. After unpacking 0B will be used. Writing extended state information... Done Setting up synaptics-dkms (1.1.1) ... Loading new synaptics-1.1.1 DKMS files... Error! Cannot locate /usr/src/synaptics-1.1.1.dkms.tar.gz. File does not exist. dpkg: error processing synaptics-dkms (--configure): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: synaptics-dkms E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: Setting up synaptics-dkms (1.1.1) ... Loading new synaptics-1.1.1 DKMS files... Error! Cannot locate /usr/src/synaptics-1.1.1.dkms.tar.gz. File does not exist. dpkg: error processing synaptics-dkms (--configure): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: synaptics-dkms Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done Any idea how I can install this? Mucho thanks in advance

  Read the article

• Strange battery behavior on laptop

  - by EpsilonVector

  My laptop is behaving rather strangely lately, and I was hoping to get some idea as to what may be causing such symptoms. The problem: When charging, very minute or so it loses connectivity with the AC adapter for a split second, and regains it back immediately. When this happens the little light that indicates the computer is plugged in does flicker off and back on, but I checked the adapter by replacing the battery on my laptop, and this indeed solves the problem, so it is probably the battery which is at fault, not the adapter (I also tried to move the adapter's wire around just to make sure it had nothing to do with torn wires). I suppose that the obvious solution is to get a new battery, but as far as battery defects go- this is a rather strange one; it loses connection with the adapter, but still powers the computer, and changing the power setting to a balanced plan (was maximum performance) seem to have solved the problem too. Is there a chance this is not simply the battery, but some kind of other electronic defect? And if not, what can cause it to behave so strangely? PS I tried to recalibrate it- didn't help.

  Read the article

• Migrate Windows Server 2008 to a new hard disk

  - by MainMa

  Hi, I have a machine with Windows Server 2008. I want to change the hard disk drive, but keep everything else. I don't have a cd/dvd drive and don't want to buy it. My first idea was to make a byte-to-byte copy of the disk with Paragon Advanced Recovery. The problem is that when I try to boot from a new hard disk, it says that there were hardware changes and that Windows must be repaired, inviting me to insert the installation disk and follow repair instructions. I searched and found that 1:1 copy is not a correct way to do things. The correct one is to restore Windows to a new hard disk from a full system backup. But to restore, I need to have a dvd drive. I tried to make a copy of the Windows Server 2008 .iso on an USB flash drive, but the drive is not bootable (while the same procedure applied to Paragon Advanced Recovery ISO produces a bootable recovery USB flash drive). Now what else can I do (except buying a dvd drive)? Is there a way either to make Windows work without doing recovery or recover Windows 2008 without using a cd drive?

  Read the article

• 10 GigE interfaces limits single connection throughput to 1 Gb on a ProCurve 4208vl

  - by wazoox

  The setup is as follow : 3 Linux servers with Intel CX4 10 GigE controllers and an X-Serve with a Myricom 10 GigE CX4 controller are connected to a ProCurve 4208vl switch, with a myriad of other machines connected through good ol' 1000 base-T. The interfaces are actually set up as 10 Gig, according to both the switch monitoring interface and the servers (ethtool, etc). However a single connection between two 10 GigE equipped machines through the switch is limited to exactly 1Gb. If I connect two of the 10 GigE machines directly with a CX4 cable, netperf reports the link bandwidth as 9000 Mb/s. NFS achieves about 550 MB/s transfers. But when I'm using the switch, the connection tops at 950 Mb/s through netperf and 110 MB/s with NFS. When I open several connections from 3 of the machines to the 4th, I get 350 MB/s of NFS transfer speed. So each individual 10 GigE ports actually can reach much more than 1 Gb, but individual connections are strictly limited to 1 Gb. Conclusion : the 10 GigE connection through the switch behaves exactly like a trunk of 10 1 Gb connections. That doesn't make any sense to me, unless HP planned these ports only for cascading switches or strictly for many-clients-to-single-server connection. Unfortunately this is NOT the envisioned setup, we need big throughput from machine to machine. Is this a not-so-known (or carefully hidden...) limitation of this type of switch? Should I suggest seppuku to the HP representative? Does anyone have any idea on how to enable a proper behaviour ? I upgraded for an hefty price from bonded 1Gb links to 10 GigE and see exactly ZERO gain! That's absolutely unacceptable.

  Read the article

• Solaris 10 invalid ARP requests from 0.0.0.0? Link up/down every hour or 2

  - by JWD

  The guys at the data center where I'm hosting a server running Solaris 10 are telling me that my server is making a lot of invalid arp requests. This is an example of a portion of what was sent to me from the logs (with Mac addresses and IP addresses changed). [mymacaddress]/0.0.0.0/0000.0000.0000/[myipaddress]/[Datestamp]) It's being logged every hour. I don't see anything in the arp tables (arp -a) or routing tables (netstat -r) and I don't see anything relating to 0.0.0.0 when snoping the arp requests. The only place I see any reference to 0.0.0.0 is if I do netstat -a for the SCTP SCTP: Local Address Remote Address Swind Send-Q Rwind Recv-Q StrsI/O State ------------------------------- ------------------------------- ------ ------ ------ ------ ------- ----------- 0.0.0.0 0.0.0.0 0 0 102400 0 32/32 CLOSED But not really sure what that means. Doesn't seem like I can disable SCTP. There are some tunable SCTP parameters but it's not something I'm familiar with. Do I have to add changes to /etc/system? Looks like sctp_heartbeat_interval might be what I need to change? If it makes any difference, I have a few solaris zones running on this server, each with their own IP address on a virtual interface. eth0:0, eth0:1, etc. Does anyone have any idea what might be causing this and how to stop it? I think the switch I'm connected to doesn't like it and momentarily drops the connection. Is there anyway to at least block those requests using ipfilter or something else? Update: This was happening more frequently but now it seems to be happening roughly every hour or every two hours. It's not consistent. I tried setting setting the link speed and duplex to match the switch port and that seemed to make it stop happening for a few hours but then it started again.

  Read the article

< Previous Page | 588 589 590 591 592 593 594 595 596 597 598 599  | Next Page >