Search Results

Search found 15797 results on 632 pages for 'session variables'.

Page 592/632 | < Previous Page | 588 589 590 591 592 593 594 595 596 597 598 599  | Next Page >

• Dlink DWA-556 Access point fails to start on 2.6.35-25 while 2.6.35-24 works. How can I do this with >2.6.35-24?

  - by Azendale

  I'm using hostapd to run an access point with a Dlink DWA-556 wireless N card. However, I can no longer get it to start when I use kernels greater than 2.6.35-24. Here's a log where I ran the uname -a&&hostapd -c <configfile> on the different kernel versions. Linux erikbandersen 2.6.35-24-generic #42-Ubuntu SMP Thu Dec 2 02:41:37 UTC 2010 x86_64 GNU/Linux Configuration file: hostapd.conf ctrl_interface_group=0 Opening raw packet socket for ifindex 248 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf nl80211: Added 802.11b mode based on 802.11g information HT40: control channel: 2 secondary channel: 6 RATE[0] rate=10 flags=0x2 RATE[1] rate=20 flags=0x6 RATE[2] rate=55 flags=0x6 RATE[3] rate=110 flags=0x6 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 Passive scanning not supported Mode: IEEE 802.11g Channel: 2 Frequency: 2417 MHz Flushing old station entries Deauthenticate all stations Using interface wlan1 with hwaddr 1c:bd:b9:d5:e8:3c and ssid 'erikbandersen.com/freewifi' wlan1: Setup of interface done. MGMT (TX callback) ACK Malformed netlink message: len=436 left=256 plen=420 256 extra bytes in the end of netlink message MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb mgmt::auth authentication: STA=3c:4a:92:0e:41:2f auth_alg=0 auth_transaction=1 status_code=0 wep=0 New STA wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: authentication OK (open system) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-AUTHENTICATE.indication(3c:4a:92:0e:41:2f, OPEN_SYSTEM) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) authentication reply: STA=3c:4a:92:0e:41:2f auth_alg=0 auth_transaction=2 resp=0 (IE len=0) MGMT (TX callback) ACK mgmt::auth cb wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: authenticated mgmt::assoc_req association request: STA=3c:4a:92:0e:41:2f capab_info=0x421 listen_interval=10 Validating WMM IE: OUI 00:50:f2 OUI type 2 OUI sub-type 0 version 1 QoS info 0x0 HT: STA 3c:4a:92:0e:41:2f HT Capabilities Info: 0x102c handle_assoc STA 3c:4a:92:0e:41:2f - no greenfield, num of non-gf stations 1 handle_assoc STA 3c:4a:92:0e:41:2f - 20 MHz HT, num of 20MHz HT STAs 1 hostapd_ht_operation_update current operation mode=0x0 hostapd_ht_operation_update new operation mode=0x7 changes=2 new AID 1 wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: association OK (aid 1) MGMT (TX callback) ACK mgmt::assoc_resp cb wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: associated (aid 1) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-ASSOCIATE.indication(3c:4a:92:0e:41:2f) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) wlan1: STA 3c:4a:92:0e:41:2f RADIUS: starting accounting session 4DAC8224-00000000 MGMT (TX callback) ACK mgmt::action cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb Signal 2 received - terminating wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DEAUTHENTICATE.indication(3c:4a:92:0e:41:2f, 1) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) Removing station 3c:4a:92:0e:41:2f hostapd_ht_operation_update current operation mode=0x7 hostapd_ht_operation_update new operation mode=0x0 changes=2 Flushing old station entries Deauthenticate all stations . Linux erikbandersen 2.6.35-25-generic #44-Ubuntu SMP Fri Jan 21 17:40:44 UTC 2011 x86_64 GNU/Linux Configuration file: hostapd.conf ctrl_interface_group=0 Opening raw packet socket for ifindex 248 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf nl80211: Added 802.11b mode based on 802.11g information Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=27 dBm HT40: control channel: 2 secondary channel: 6 RATE[0] rate=10 flags=0x2 RATE[1] rate=20 flags=0x6 RATE[2] rate=55 flags=0x6 RATE[3] rate=110 flags=0x6 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 Passive scanning not supported Mode: IEEE 802.11g Channel: 2 Frequency: 2417 MHz Could not set channel for kernel driver wlan1: Unable to setup interface. My wireless card is listed as 02:00.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) by lspci. Am I doing it wrong and there's a new way of doing it? I'm holding off upgrading to Natty because of this. What changed between the versions that would cause this? Should I report it as a bug?

  Read the article

• Changing an HTML Form's Target with jQuery

  - by Rick Strahl

  This is a question that comes up quite frequently: I have a form with several submit or link buttons and one or more of the buttons needs to open a new Window. How do I get several buttons to all post to the right window? If you're building ASP.NET forms you probably know that by default the Web Forms engine sends button clicks back to the server as a POST operation. A server form has a <form> tag which expands to this: <form method="post" action="default.aspx" id="form1"> Now you CAN change the target of the form and point it to a different window or frame, but the problem with that is that it still affects ALL submissions of the current form. If you multiple buttons/links and they need to go to different target windows/frames you can't do it easily through the <form runat="server"> tag. Although this discussion uses ASP.NET WebForms as an example, realistically this is a general HTML problem although likely more common in WebForms due to the single form metaphor it uses. In ASP.NET MVC for example you'd have more options by breaking out each button into separate forms with its own distinct target tag. However, even with that option it's not always possible to break up forms - for example if multiple targets are required but all targets require the same form data to the be posted. A common scenario here is that you might have a button (or link) that you click where you still want some server code to fire but at the end of the request you actually want to display the content in a new window. A common operation where this happens is report generation: You click a button and the server generates a report say in PDF format and you then want to display the PDF result in a new window without killing the content in the current window. Assuming you have other buttons on the same Page that need to post to base window how do you get the button click to go to a new window? Can't  you just use a LinkButton or other Link Control? At first glance you might think an easy way to do this is to use an ASP.NET LinkButton to do this - after all a LinkButton creates a hyper link that CAN accept a target and it also posts back to the server, right? However, there's no Target property, although you can set the target HTML attribute easily enough. Code like this looks reasonable: <asp:LinkButton runat="server" ID="btnNewTarget" Text="New Target" target="_blank" OnClick="bnNewTarget_Click" /> But if you try this you'll find that it doesn't work. Why? Because ASP.NET creates postbacks with JavaScript code that operates on the current window/frame: <a id="btnNewTarget" target="_blank" href="javascript:__doPostBack(&#39;btnNewTarget&#39;,&#39;&#39;)">New Target</a> What happens with a target tag is that before the JavaScript actually executes a new window is opened and the focus shifts to the new window. The new window of course is empty and has no __doPostBack() function nor access to the old document. So when you click the link a new window opens but the window remains blank without content - no server postback actually occurs. Natch that idea. Setting the Form Target for a Button Control or LinkButton So, in order to send Postback link controls and buttons to another window/frame, both require that the target of the form gets changed dynamically when the button or link is clicked. Luckily this is rather easy to do however using a little bit of script code and jQuery. Imagine you have two buttons like this that should go to another window: <asp:LinkButton runat="server" ID="btnNewTarget" Text="New Target" OnClick="ClickHandler" /> <asp:Button runat="server" ID="btnButtonNewTarget" Text="New Target Button" OnClick="ClickHandler" /> ClickHandler in this case is any routine that generates the output you want to display in the new window. Generally this output will not come from the current page markup but is generated externally - like a PDF report or some report generated by another application component or tool. The output generally will be either generated by hand or something that was generated to disk to be displayed with Response.Redirect() or Response.TransmitFile() etc. Here's the dummy handler that just generates some HTML by hand and displays it: protected void ClickHandler(object sender, EventArgs e) { // Perform some operation that generates HTML or Redirects somewhere else Response.Write("Some custom output would be generated here (PDF, non-Page HTML etc.)"); // Make sure this response doesn't display the page content // Call Response.End() or Response.Redirect() Response.End(); } To route this oh so sophisticated output to an alternate window for both the LinkButton and Button Controls, you can use the following simple script code: <script type="text/javascript"> $("#btnButtonNewTarget,#btnNewTarget").click(function () { $("form").attr("target", "_blank"); }); </script> So why does this work where the target attribute did not? The difference here is that the script fires BEFORE the target is changed to the new window. When you put a target attribute on a link or form the target is changed as the very first thing before the link actually executes. IOW, the link literally executes in the new window when it's done this way. By attaching a click handler, though we're not navigating yet so all the operations the script code performs (ie. __doPostBack()) and the collection of Form variables to post to the server all occurs in the current page. By changing the target from within script code the target change fires as part of the form submission process which means it runs in the correct context of the current page. IOW - the input for the POST is from the current page, but the output is routed to a new window/frame. Just what we want in this scenario. Voila you can dynamically route output to the appropriate window.© Rick Strahl, West Wind Technologies, 2005-2011Posted in ASP.NET  HTML  jQuery  

  Read the article

• Resetting Your Oracle User Password with SQL Developer

  - by thatjeffsmith

  There’s nothing more annoying than having to email, call, or log a support ticket to have one of your accounts reset. This is no less annoying in the Oracle database. Those pesky security folks have determined that your password should only be valid for X days, and your time is up. Time to reset the password! Except…you can’t log into the database to reset your password. What now? Wait a second, look at this nifty thing I see in SQL Developer: Right click on my connection, reset password not available! Why not? The JDBC Driver Doesn’t Support This Operation We can’t make this call over the Oracle JDBC layer, because it hasn’t been implemented. However our primary interface, OCI, does indeed support this. In order to use the Oracle Call Interface (OCI), you need to have an Oracle Client on your machine. The good news is that this is fairly easy to get going. The Instant Client will do. You have two options, the full or ‘Lite’ Instant Clients. If you want SQL*Plus and the other client tools, go for the full. If you just want the basic drivers, go for the Lite. Either of these is fine, but mind the bit level and version of Oracle! Make sure you get a 32 bit Instant Client if you run 32 bit SQL Developer or 64 bit if you run 64 Here’s the download link What, you didn’t believe me? Mind the version of Oracle too! You want to be at the same level or higher of the database you’re working with. You can use a 11.2.0.3 client with 11.2.0.1 database but not a 10gR2 client with 11gR2 database. Clear as mud? Download and Extract Put it where you want – Program Files is as good as place as any if you have the rights. When you’re done, copy that directory path you extracted the archive to, because we’re going to add it to your Windows PATH environment variable. The easiest way to find this in Windows 7 is to open the Start dialog and type ‘path’. In Windows 8 you’ll cast your spell and wave at your screen until something happens. I recommend you put it up front so we find our DLLs first. Now with that set, let’s start up SQL Developer. Check the Connection Context menu again Bingo! What happened there? SQL Developer looks to see if it can find the OCI resources. Guess where it looks? That’s right, the PATH. If it finds what it’s looking for, and confirms the bit level is right, it will activate the Reset Password option. We have a Preference to ‘force’ an OCI/THICK connection that gives you a few other edge case features, but you do not need to enable this to activate the Reset Password. Not necessary, but won’t hurt anything either. There are a few actual benefits to using OCI powered connections, but that’s beyond the scope of today’s blog post…to be continued. Ok, so we’re ready to go. Now, where was I again? Oh yeah, my password has expired… Right click on your connection and now choose ‘Reset Password’ You’ll need to know your existing password and select a new one that meets your databases’s security standards. I Need Another Option, This Ain’t Working! If you have another account in the database, you can use the DBA Panel to reset a user’s password, or of course you can spark up a SQL*Plus session and issue the ALTER USER JEFF IDENTIFIED BY _________; command – but you knew this already, yes? I need more help ‘installing’ the Instant Client, help! There are lots and lots of resources out there on this subject. But I also know from personal experience that many of you have problems getting this to ‘work.’ The key things to remember is to download the right bit level AND make sure the client install directory is in your path. I know many folks that will just ‘install’ the Instant Client directly to one of their ‘bin’ type directories. You can do that if you want, but I prefer the cleaner method. Of course if you lack admin privs to change the PATH variable, that might be your only option. Or you could do what the original ORA- message indicated and ‘contact your DBA.’

  Read the article

• Use WLST to Delete All JMS Messages From a Destination

  - by james.bayer

  I got a question today about whether WebLogic Server has any tools to delete all messages from a JMS Queue.  It just so happens that the WLS Console has this capability already.  It’s available on the screen after the “Show Messages” button is clicked on a destination’s Monitoring tab as seen in the screen shot below. The console is great for something ad-hoc, but what if I want to automate this?  Well it just so happens that the console is just a weblogic application layered on top of the JMX Management interface.  If you look at the MBean Reference, you’ll find a JMSDestinationRuntimeMBean that includes the operation deleteMessages that takes a JMS Message Selector as an argument.  If you pass an empty string, that is essentially a wild card that matches all messages. Coding a stand-alone JMX client for this is kind of lame, so let’s do something more suitable to scripting.  In addition to the console, WebLogic Scripting Tool (WLST) based on Jython is another way to browse and invoke MBeans, so an equivalent interactive shell session to delete messages from a destination would looks like this: D:\Oracle\fmw11gr1ps3\user_projects\domains\hotspot_domain\bin>setDomainEnv.cmd D:\Oracle\fmw11gr1ps3\user_projects\domains\hotspot_domain>java weblogic.WLST   Initializing WebLogic Scripting Tool (WLST) ...   Welcome to WebLogic Server Administration Scripting Shell   Type help() for help on available commands   wls:/offline> connect('weblogic','welcome1','t3://localhost:7001') Connecting to t3://localhost:7001 with userid weblogic ... Successfully connected to Admin Server 'AdminServer' that belongs to domain 'hotspot_domain'.   Warning: An insecure protocol was used to connect to the server. To ensure on-the-wire security, the SSL port or Admin port should be used instead.   wls:/hotspot_domain/serverConfig> serverRuntime() Location changed to serverRuntime tree. This is a read-only tree with ServerRuntimeMBean as the root. For more help, use help(serverRuntime)   wls:/hotspot_domain/serverRuntime> cd('JMSRuntime/AdminServer.jms/JMSServers/JMSServer-0/Destinations/SystemModule-0!Queue-0') wls:/hotspot_domain/serverRuntime/JMSRuntime/AdminServer.jms/JMSServers/JMSServer-0/Destinations/SystemModule-0!Queue-0> ls() dr-- DurableSubscribers   -r-- BytesCurrentCount 0 -r-- BytesHighCount 174620 -r-- BytesPendingCount 0 -r-- BytesReceivedCount 253548 -r-- BytesThresholdTime 0 -r-- ConsumersCurrentCount 0 -r-- ConsumersHighCount 0 -r-- ConsumersTotalCount 0 -r-- ConsumptionPaused false -r-- ConsumptionPausedState Consumption-Enabled -r-- DestinationInfo javax.management.openmbean.CompositeDataSupport(compositeType=javax.management.openmbean.CompositeType(name=DestinationInfo,items=((itemName=ApplicationName,itemType=javax.management.openmbean.SimpleType(name=java.lang.String)),(itemName=ModuleName,itemType=javax.management.openmbean.SimpleType(name=java.lang.String)),(itemName openmbean.SimpleType(name=java.lang.Boolean)),(itemName=SerializedDestination,itemType=javax.management.openmbean.SimpleType(name=java.lang.String)),(itemName=ServerName,itemType=javax.management.openmbean.SimpleType(name=java.lang.String)),(itemName=Topic,itemType=javax.management.openmbean.SimpleType(name=java.lang.Boolean)),(itemName=VersionNumber,itemType=javax.management.op ule-0!Queue-0, Queue=true, SerializedDestination=rO0ABXNyACN3ZWJsb2dpYy5qbXMuY29tbW9uLkRlc3RpbmF0aW9uSW1wbFSmyJ1qZfv8DAAAeHB3kLZBABZTeXN0ZW1Nb2R1bGUtMCFRdWV1ZS0wAAtKTVNTZXJ2ZXItMAAOU3lzdGVtTW9kdWxlLTABAANBbGwCAlb6IS6T5qL/AAAACgEAC0FkbWluU2VydmVyAC2EGgJW+iEuk+ai/wAAAAsBAAtBZG1pblNlcnZlcgAthBoAAQAQX1dMU19BZG1pblNlcnZlcng=, ServerName=JMSServer-0, Topic=false, VersionNumber=1}) -r-- DestinationType Queue -r-- DurableSubscribers null -r-- InsertionPaused false -r-- InsertionPausedState Insertion-Enabled -r-- MessagesCurrentCount 0 -r-- MessagesDeletedCurrentCount 3 -r-- MessagesHighCount 2 -r-- MessagesMovedCurrentCount 0 -r-- MessagesPendingCount 0 -r-- MessagesReceivedCount 3 -r-- MessagesThresholdTime 0 -r-- Name SystemModule-0!Queue-0 -r-- Paused false -r-- ProductionPaused false -r-- ProductionPausedState Production-Enabled -r-- State advertised_in_cluster_jndi -r-- Type JMSDestinationRuntime   -r-x closeCursor Void : String(cursorHandle) -r-x deleteMessages Integer : String(selector) -r-x getCursorEndPosition Long : String(cursorHandle) -r-x getCursorSize Long : String(cursorHandle) -r-x getCursorStartPosition Long : String(cursorHandle) -r-x getItems javax.management.openmbean.CompositeData[] : String(cursorHandle),Long(start),Integer(count) -r-x getMessage javax.management.openmbean.CompositeData : String(cursorHandle),Long(messageHandle) -r-x getMessage javax.management.openmbean.CompositeData : String(cursorHandle),String(messageID) -r-x getMessage javax.management.openmbean.CompositeData : String(messageID) -r-x getMessages String : String(selector),Integer(timeout) -r-x getMessages String : String(selector),Integer(timeout),Integer(state) -r-x getNext javax.management.openmbean.CompositeData[] : String(cursorHandle),Integer(count) -r-x getPrevious javax.management.openmbean.CompositeData[] : String(cursorHandle),Integer(count) -r-x importMessages Void : javax.management.openmbean.CompositeData[],Boolean(replaceOnly) -r-x moveMessages Integer : String(java.lang.String),javax.management.openmbean.CompositeData,Integer(java.lang.Integer) -r-x moveMessages Integer : String(selector),javax.management.openmbean.CompositeData -r-x pause Void : -r-x pauseConsumption Void : -r-x pauseInsertion Void : -r-x pauseProduction Void : -r-x preDeregister Void : -r-x resume Void : -r-x resumeConsumption Void : -r-x resumeInsertion Void : -r-x resumeProduction Void : -r-x sort Long : String(cursorHandle),Long(start),String[](fields),Boolean[](ascending)   wls:/hotspot_domain/serverRuntime/JMSRuntime/AdminServer.jms/JMSServers/JMSServer-0/Destinations/SystemModule-0!Queue-0> cmo.deleteMessages('') 2 where the domain name is “hotspot_domain”, the JMS Server name is “JMSServer-0”, the Queue name is “Queue-0” and the System Module is named “SystemModule-0”.  To invoke the operation, I use the “cmo” object, which is the “Current Management Object” that represents the currently navigated to MBean.  The 2 indicates that two messages were deleted.  Combining this WLST code with a recent post by my colleague Steve that shows you how to use an encrypted file to store the authentication credentials, you could easily turn this into a secure automated script.  If you need help with that step, a long while back I blogged about some WLST basics.  Happy scripting.

  Read the article

• Creating an SMF service for mercurial web server

  - by Chris W Beal

  I'm working on a project at the moment, which has a number of contributers. We're managing the project gate (which is stand alone) with mercurial. We want to have an easy way of seeing the changelog, so we can show management what is going on.  Luckily mercurial provides a basic web server which allows you to see the changes, and drill in to change sets. This can be run as a daemon, but as it was running on our build server, every time it was rebooted, someone needed to remember to start the process again. This is of course a classic usage of SMF. Now I'm not an experienced person at writing SMF services, so it took me 1/2 an hour or so to figure it out the first time. But going forward I should know what I'm doing a bit better. I did reference this doc extensively. Taking a step back, the command to start the mercurial web server is $ hg serve -p <port number> -d So we somehow need to get SMF to run that command for us. In the simplest form, SMF services are really made up of two components. The manifest Usually lives in /var/svc/manifest somewhere Can be imported from any location The method Usually live in /lib/svc/method I simply put the script straight in that directory. Not very repeatable, but it worked Can take an argument of start, stop, or refresh Lets start with the manifest. This looks pretty complex, but all it's doing is describing the service name, the dependencies, the start and stop methods, and some properties. The properties can be by instance, that is to say I could have multiple hg serve processes handling different mercurial projects, on different ports simultaneously Here is the manifest I wrote. I stole extensively from the examples in the Documentation. So my manifest looks like this $ cat hg-serve.xml <?xml version="1.0"?> <!DOCTYPE service_bundle SYSTEM "/usr/share/lib/xml/dtd/service_bundle.dtd.1"> <service_bundle type='manifest' name='hg-serve'> <service name='application/network/hg-serve' type='service' version='1'> <dependency name='network' grouping='require_all' restart_on='none' type='service'> <service_fmri value='svc:/milestone/network:default' /> </dependency> <exec_method type='method' name='start' exec='/lib/svc/method/hg-serve %m' timeout_seconds='2' /> <exec_method type='method' name='stop' exec=':kill' timeout_seconds='2'> </exec_method> <instance name='project-gate' enabled='true'> <method_context> <method_credential user='root' group='root' /> </method_context> <property_group name='hg-serve' type='application'> <propval name='path' type='astring' value='/src/project-gate'/> <propval name='port' type='astring' value='9998' /> </property_group> </instance> <stability value='Evolving' /> <template> <common_name> <loctext xml:lang='C'>hg-serve</loctext> </common_name> <documentation> <manpage title='hg' section='1' /> </documentation> </template> </service> </service_bundle> So the only things I had to decide on in this are the service name "application/network/hg-serve" the start and stop methods (more of which later) and the properties. This is the information I need to pass to the start method script. In my case the port I want to start the web server on "9998", and the path to the source gate "/src/project-gate". These can be read in to the start method. So now lets look at the method scripts $ cat /lib/svc/method/hg-serve #!/sbin/sh # # # Copyright (c) 2012, Oracle and/or its affiliates. All rights reserved. # # Standard prolog # . /lib/svc/share/smf_include.sh if [ -z $SMF_FMRI ]; then echo "SMF framework variables are not initialized." exit $SMF_EXIT_ERR fi # # Build the command line flags # # Get the port and directory from the SMF properties port=`svcprop -c -p hg-serve/port $SMF_FMRI` dir=`svcprop -c -p hg-serve/path $SMF_FMRI` echo "$1" case "$1" in 'start') cd $dir /usr/bin/hg serve -d -p $port ;; *) echo "Usage: $0 {start|refresh|stop}" exit 1 ;; esac exit $SMF_EXIT_OK This is all pretty self explanatory, we read the port and directory using svcprop, and use those simply to run a command in the start case. We don't need to implement a stop case, as the manifest says to use "exec=':kill'for the stop method. Now all we need to do is import the manifest and start the service, but first verify the manifest # svccfg verify /path/to/hg-serve.xml If that doesn't give an error try importing it # svccfg import /path/to/hg-serve.xml If like me you originally put the hg-serve.xml file in /var/svc/manifest somewhere you'll get an error and told to restart the import service svccfg: Restarting svc:/system/manifest-import The manifest being imported is from a standard location and should be imported with the command : svcadm restart svc:/system/manifest-import # svcadm restart svc:/system/manifest-import and you're nearly done. You can look at the service using svcs -l # svcs -l hg-serve fmri svc:/application/network/hg-serve:project-gate name hg-serve enabled false state disabled next_state none state_time Thu May 31 16:11:47 2012 logfile /var/svc/log/application-network-hg-serve:project-gate.log restarter svc:/system/svc/restarter:default contract_id 15749 manifest /var/svc/manifest/network/hg/hg-serve.xml dependency require_all/none svc:/milestone/network:default (online) And look at the interesting properties # svcprop hg-serve hg-serve/path astring /src/project-gate hg-serve/port astring 9998 ...stuff deleted.... Then simply enable the service and if every things gone right, you can point your browser at http://server:9998 and get a nice graphical log of project activity. # svcadm enable hg-serve # svcs -l hg-serve fmri svc:/application/network/hg-serve:project-gate name hg-serve enabled true state online next_state none state_time Thu May 31 16:18:11 2012 logfile /var/svc/log/application-network-hg-serve:project-gate.log restarter svc:/system/svc/restarter:default contract_id 15858 manifest /var/svc/manifest/network/hg/hg-serve.xml dependency require_all/none svc:/milestone/network:default (online) None of this is rocket science, but a bit fiddly. Hence I thought I'd blog it. It might just be you see this in google and it clicks with you more than one of the many other blogs or how tos about it. Plus I can always refer back to it myself in 3 weeks, when I want to add another project to the server, and I've forgotten how to do it.

  Read the article

• How to solve exception_priv _instruction exception while running destop project? [on hold]

  - by Haritha

  While running desktop project im getting exception_priv _instruction how to solve this??? while running this page is coming # # A fatal error has been detected by the Java Runtime Environment: # # EXCEPTION_PRIV_INSTRUCTION (0xc0000096) at pc=0x02f5a92b, pid=3012, tid=3104 # # JRE version: 7.0-b147 # Java VM: Java HotSpot(TM) Client VM (21.0-b17 mixed mode, sharing windows-x86 ) # Problematic frame: # C 0x02f5a92b # # Failed to write core dump. Minidumps are not enabled by default on client versions of Windows # # If you would like to submit a bug report, please visit: # http://bugreport.sun.com/bugreport/crash.jsp # The crash happened outside the Java Virtual Machine in native code. # See problematic frame for where to report the bug. # --------------- T H R E A D --------------- Current thread (0x02f5a800): JavaThread "LWJGL Application" [_thread_in_native, id=3104, stack(0x076f0000,0x07740000)] siginfo: ExceptionCode=0xc0000096 Registers: EAX=0x000df4f0, EBX=0x32afc180, ECX=0x000df4f0, EDX=0x00000020 ESP=0x0773f768, EBP=0x0773f790, ESI=0x32afc180, EDI=0x02f5a800 EIP=0x02f5a92b, EFLAGS=0x00010206 Top of Stack: (sp=0x0773f768) 0x0773f768: 02bd429c 02bd429c 0773f770 32afc180 0x0773f778: 0773f7b8 32b022c8 00000000 32afc180 0x0773f788: 00000000 0773f7a0 0773f7dc 00943187 0x0773f798: 229ec1c0 00948839 69081736 00000000 0x0773f7a8: 089b0048 00000000 00000014 00001406 0x0773f7b8: 00000002 0773f7bc 32afbeb0 0773f7f8 0x0773f7c8: 32b022c8 00000000 32afbf00 0773f7a0 0x0773f7d8: 0773f7f0 0773f81c 00943187 69081736 Instructions: (pc=0x02f5a92b) 0x02f5a90b: 00 43 00 00 00 00 f0 bc 02 e8 00 e9 22 40 f7 73 0x02f5a91b: 07 85 a5 94 00 90 f7 73 07 50 cc a0 6d d8 49 c0 0x02f5a92b: 6d 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x02f5a93b: 00 00 00 00 00 00 00 00 00 08 80 3d 37 00 00 00 Register to memory mapping: EAX=0x000df4f0 is an unknown value EBX=0x32afc180 is an oop {method} - klass: {other class} ECX=0x000df4f0 is an unknown value EDX=0x00000020 is an unknown value ESP=0x0773f768 is pointing into the stack for thread: 0x02f5a800 EBP=0x0773f790 is pointing into the stack for thread: 0x02f5a800 ESI=0x32afc180 is an oop {method} - klass: {other class} EDI=0x02f5a800 is a thread Stack: [0x076f0000,0x07740000], sp=0x0773f768, free space=317k Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code) C 0x02f5a92b j org.lwjgl.opengl.GL11.glVertexPointer(IILjava/nio/FloatBuffer;)V+48 j com.badlogic.gdx.backends.lwjgl.LwjglGL10.glVertexPointer(IIILjava/nio/Buffer;)V+53 j com.badlogic.gdx.graphics.glutils.VertexArray.bind()V+149 j com.badlogic.gdx.graphics.Mesh.bind()V+25 j com.badlogic.gdx.graphics.Mesh.render(IIIZ)V+32 j com.badlogic.gdx.graphics.Mesh.render(III)V+8 j com.badlogic.gdx.graphics.g2d.SpriteBatch.flush()V+197 j com.badlogic.gdx.graphics.g2d.SpriteBatch.switchTexture(Lcom/badlogic/gdx/graphics/Texture;)V+1 j com.badlogic.gdx.graphics.g2d.SpriteBatch.draw(Lcom/badlogic/gdx/graphics/Texture;FFFF)V+33 j sevenseas.game.WorldRenderer.drawBob()V+54 j sevenseas.game.WorldRenderer.render()V+12 j sevenseas.game.GameClass.render(F)V+38 j com.badlogic.gdx.Game.render()V+19 j com.badlogic.gdx.backends.lwjgl.LwjglApplication.mainLoop()V+642 j com.badlogic.gdx.backends.lwjgl.LwjglApplication$1.run()V+27 v ~StubRoutines::call_stub V [jvm.dll+0x122c7e] V [jvm.dll+0x1c9c0e] V [jvm.dll+0x122e73] V [jvm.dll+0x122ed7] V [jvm.dll+0xccd1f] V [jvm.dll+0x14433f] V [jvm.dll+0x171549] C [msvcr100.dll+0x5c6de] endthreadex+0x3a C [msvcr100.dll+0x5c788] endthreadex+0xe4 C [kernel32.dll+0xb713] GetModuleFileNameA+0x1b4 Java frames: (J=compiled Java code, j=interpreted, Vv=VM code) j org.lwjgl.opengl.GL11.nglVertexPointer(IIIJJ)V+0 j org.lwjgl.opengl.GL11.glVertexPointer(IILjava/nio/FloatBuffer;)V+48 j com.badlogic.gdx.backends.lwjgl.LwjglGL10.glVertexPointer(IIILjava/nio/Buffer;)V+53 j com.badlogic.gdx.graphics.glutils.VertexArray.bind()V+149 j com.badlogic.gdx.graphics.Mesh.bind()V+25 j com.badlogic.gdx.graphics.Mesh.render(IIIZ)V+32 j com.badlogic.gdx.graphics.Mesh.render(III)V+8 j com.badlogic.gdx.graphics.g2d.SpriteBatch.flush()V+197 j com.badlogic.gdx.graphics.g2d.SpriteBatch.switchTexture(Lcom/badlogic/gdx/graphics/Texture;)V+1 j com.badlogic.gdx.graphics.g2d.SpriteBatch.draw(Lcom/badlogic/gdx/graphics/Texture;FFFF)V+33 j sevenseas.game.WorldRenderer.drawBob()V+54 j sevenseas.game.WorldRenderer.render()V+12 j sevenseas.game.GameClass.render(F)V+38 j com.badlogic.gdx.Game.render()V+19 j com.badlogic.gdx.backends.lwjgl.LwjglApplication.mainLoop()V+642 j com.badlogic.gdx.backends.lwjgl.LwjglApplication$1.run()V+27 v ~StubRoutines::call_stub --------------- P R O C E S S --------------- Java Threads: ( => current thread ) 0x003d6c00 JavaThread "DestroyJavaVM" [_thread_blocked, id=3240, stack(0x008c0000,0x00910000)] =>0x02f5a800 JavaThread "LWJGL Application" [_thread_in_native, id=3104, stack(0x076f0000,0x07740000)] 0x02bcf000 JavaThread "Service Thread" daemon [_thread_blocked, id=2612, stack(0x02e00000,0x02e50000)] 0x02bc1000 JavaThread "C1 CompilerThread0" daemon [_thread_blocked, id=2776, stack(0x02db0000,0x02e00000)] 0x02bbf400 JavaThread "Attach Listener" daemon [_thread_blocked, id=2448, stack(0x02d60000,0x02db0000)] 0x02bbe000 JavaThread "Signal Dispatcher" daemon [_thread_blocked, id=1764, stack(0x02d10000,0x02d60000)] 0x02bb8000 JavaThread "Finalizer" daemon [_thread_blocked, id=3864, stack(0x02cc0000,0x02d10000)] 0x02bb3400 JavaThread "Reference Handler" daemon [_thread_blocked, id=2424, stack(0x02c70000,0x02cc0000)] Other Threads: 0x02bb1800 VMThread [stack: 0x02c20000,0x02c70000] [id=3076] 0x02bd1000 WatcherThread [stack: 0x02e50000,0x02ea0000] [id=3276] VM state:not at safepoint (normal execution) VM Mutex/Monitor currently owned by a thread: None Heap def new generation total 4928K, used 2571K [0x229c0000, 0x22f10000, 0x27f10000) eden space 4416K, 46% used [0x229c0000, 0x22bc2e38, 0x22e10000) from space 512K, 100% used [0x22e90000, 0x22f10000, 0x22f10000) to space 512K, 0% used [0x22e10000, 0x22e10000, 0x22e90000) tenured generation total 10944K, used 634K [0x27f10000, 0x289c0000, 0x329c0000) the space 10944K, 5% used [0x27f10000, 0x27faea60, 0x27faec00, 0x289c0000) compacting perm gen total 12288K, used 1655K [0x329c0000, 0x335c0000, 0x369c0000) the space 12288K, 13% used [0x329c0000, 0x32b5dc58, 0x32b5de00, 0x335c0000) ro space 10240K, 42% used [0x369c0000, 0x36dfc660, 0x36dfc800, 0x373c0000) rw space 12288K, 53% used [0x373c0000, 0x37a38180, 0x37a38200, 0x37fc0000) Code Cache [0x00940000, 0x009d8000, 0x02940000) total_blobs=305 nmethods=80 adapters=158 free_code_cache=32183Kb largest_free_block=32955904 Dynamic libraries: 0x00400000 - 0x0042f000 C:\Program Files\Java\jre7\bin\javaw.exe 0x7c900000 - 0x7c9af000 C:\WINDOWS\system32\ntdll.dll 0x7c800000 - 0x7c8f6000 C:\WINDOWS\system32\kernel32.dll 0x77dd0000 - 0x77e6b000 C:\WINDOWS\system32\ADVAPI32.dll 0x77e70000 - 0x77f02000 C:\WINDOWS\system32\RPCRT4.dll 0x77fe0000 - 0x77ff1000 C:\WINDOWS\system32\Secur32.dll 0x7e410000 - 0x7e4a1000 C:\WINDOWS\system32\USER32.dll 0x77f10000 - 0x77f59000 C:\WINDOWS\system32\GDI32.dll 0x773d0000 - 0x774d3000 C:\WINDOWS\WinSxS\x86_Microsoft.Windows.Common-Controls_6595b64144ccf1df_6.0.2600.5512_x-ww_35d4ce83\COMCTL32.dll 0x77c10000 - 0x77c68000 C:\WINDOWS\system32\msvcrt.dll 0x77f60000 - 0x77fd6000 C:\WINDOWS\system32\SHLWAPI.dll 0x76390000 - 0x763ad000 C:\WINDOWS\system32\IMM32.DLL 0x629c0000 - 0x629c9000 C:\WINDOWS\system32\LPK.DLL 0x74d90000 - 0x74dfb000 C:\WINDOWS\system32\USP10.dll 0x78aa0000 - 0x78b5e000 C:\Program Files\Java\jre7\bin\msvcr100.dll 0x6d940000 - 0x6dc61000 C:\Program Files\Java\jre7\bin\client\jvm.dll 0x71ad0000 - 0x71ad9000 C:\WINDOWS\system32\WSOCK32.dll 0x71ab0000 - 0x71ac7000 C:\WINDOWS\system32\WS2_32.dll 0x71aa0000 - 0x71aa8000 C:\WINDOWS\system32\WS2HELP.dll 0x76b40000 - 0x76b6d000 C:\WINDOWS\system32\WINMM.dll 0x76bf0000 - 0x76bfb000 C:\WINDOWS\system32\PSAPI.DLL 0x6d8d0000 - 0x6d8dc000 C:\Program Files\Java\jre7\bin\verify.dll 0x6d370000 - 0x6d390000 C:\Program Files\Java\jre7\bin\java.dll 0x6d920000 - 0x6d933000 C:\Program Files\Java\jre7\bin\zip.dll 0x6cec0000 - 0x6cf42000 C:\Documents and Settings\7stl0225\Local Settings\Temp\libgdx7stl0225\37fe1abc\gdx.dll 0x10000000 - 0x1004c000 C:\Documents and Settings\7stl0225\Local Settings\Temp\libgdx7stl0225\52d76f2b\lwjgl.dll 0x5ed00000 - 0x5edcc000 C:\WINDOWS\system32\OPENGL32.dll 0x68b20000 - 0x68b40000 C:\WINDOWS\system32\GLU32.dll 0x73760000 - 0x737ab000 C:\WINDOWS\system32\DDRAW.dll 0x73bc0000 - 0x73bc6000 C:\WINDOWS\system32\DCIMAN32.dll 0x77c00000 - 0x77c08000 C:\WINDOWS\system32\VERSION.dll 0x070b0000 - 0x07115000 C:\DOCUME~1\7stl0225\LOCALS~1\Temp\libgdx7stl0225\52d76f2b\OpenAL32.dll 0x7c9c0000 - 0x7d1d7000 C:\WINDOWS\system32\SHELL32.dll 0x774e0000 - 0x7761d000 C:\WINDOWS\system32\ole32.dll 0x5ad70000 - 0x5ada8000 C:\WINDOWS\system32\uxtheme.dll 0x76fd0000 - 0x7704f000 C:\WINDOWS\system32\CLBCATQ.DLL 0x77050000 - 0x77115000 C:\WINDOWS\system32\COMRes.dll 0x77120000 - 0x771ab000 C:\WINDOWS\system32\OLEAUT32.dll 0x73f10000 - 0x73f6c000 C:\WINDOWS\system32\dsound.dll 0x76c30000 - 0x76c5e000 C:\WINDOWS\system32\WINTRUST.dll 0x77a80000 - 0x77b15000 C:\WINDOWS\system32\CRYPT32.dll 0x77b20000 - 0x77b32000 C:\WINDOWS\system32\MSASN1.dll 0x76c90000 - 0x76cb8000 C:\WINDOWS\system32\IMAGEHLP.dll 0x72d20000 - 0x72d29000 C:\WINDOWS\system32\wdmaud.drv 0x72d10000 - 0x72d18000 C:\WINDOWS\system32\msacm32.drv 0x77be0000 - 0x77bf5000 C:\WINDOWS\system32\MSACM32.dll 0x77bd0000 - 0x77bd7000 C:\WINDOWS\system32\midimap.dll 0x73ee0000 - 0x73ee4000 C:\WINDOWS\system32\KsUser.dll 0x755c0000 - 0x755ee000 C:\WINDOWS\system32\msctfime.ime 0x69000000 - 0x691a9000 C:\WINDOWS\system32\sisgl.dll 0x73b30000 - 0x73b45000 C:\WINDOWS\system32\mscms.dll 0x73000000 - 0x73026000 C:\WINDOWS\system32\WINSPOOL.DRV 0x66e90000 - 0x66ed1000 C:\WINDOWS\system32\icm32.dll 0x07760000 - 0x0778d000 C:\Program Files\WordWeb\WHook.dll 0x74c80000 - 0x74cac000 C:\WINDOWS\system32\OLEACC.dll 0x76080000 - 0x760e5000 C:\WINDOWS\system32\MSVCP60.dll VM Arguments: jvm_args: -Dfile.encoding=Cp1252 java_command: sevenseas.game.MainDesktop Launcher Type: SUN_STANDARD Environment Variables: PATH=C:/Program Files/Java/jre7/bin/client;C:/Program Files/Java/jre7/bin;C:/Program Files/Java/jre7/lib/i386;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Program Files\Java\jdk1.7.0\bin;C:\eclipse; USERNAME=7stl0225 OS=Windows_NT PROCESSOR_IDENTIFIER=x86 Family 15 Model 4 Stepping 1, GenuineIntel --------------- S Y S T E M --------------- OS: Windows XP Build 2600 Service Pack 3 CPU:total 1 (1 cores per cpu, 1 threads per core) family 15 model 4 stepping 1, cmov, cx8, fxsr, mmx, sse, sse2, sse3 Memory: 4k page, physical 2031088k(939252k free), swap 3969920k(3011396k free) vm_info: Java HotSpot(TM) Client VM (21.0-b17) for windows-x86 JRE (1.7.0-b147), built on Jun 27 2011 02:25:52 by "java_re" with unknown MS VC++:1600 time: Sat Oct 26 12:35:14 2013 elapsed time: 0 seconds

  Read the article

• Establishing WebLogic Server HTTPS Trust of IIS Using a Microsoft Local Certificate Authority

  - by user647124

  Everyone agrees that self-signed and demo certificates for SSL and HTTPS should never be used in production and preferred not to be used elsewhere. Most self-signed and demo certificates are provided by vendors with the intention that they are used only to integrate within the same environment. In a vendor’s perfect world all application servers in a given enterprise are from the same vendor, which makes this lack of interoperability in a non-production environment an advantage. For us working in the real world, where not only do we not use a single vendor everywhere but have to make do with self-signed certificates for all but production, testing HTTPS between an IIS ASP.NET service provider and a WebLogic J2EE consumer application can be very frustrating to set up. It was for me, especially having found many blogs and discussion threads where various solutions were described but did not quite work and were all mostly similar but just a little bit different. To save both you and my future (who always seems to forget the hardest-won lessons) all of the pain and suffering, I am recording the steps that finally worked here for reference and sanity. How You Know You Need This The first cold clutches of dread that tells you it is going to be a long day is when you attempt to a WSDL published by IIS in WebLogic over HTTPS and you see the following: <Jul 30, 2012 2:51:31 PM EDT> <Warning> <Security> <BEA-090477> <Certificate chain received from myserver.mydomain.com - 10.555.55.123 was not trusted causing SSL handshake failure.> weblogic.wsee.wsdl.WsdlException: Failed to read wsdl file from url due to -- javax.net.ssl.SSLKeyException: [Security:090477]Certificate chain received from myserver02.mydomain.com - 10.555.55.123 was not trusted causing SSL handshake failure. The above is what started a three day sojourn into searching for a solution. Even people who had solved it before would tell me how they did, and then shrug when I demonstrated that the steps did not end in the success they claimed I would experience. Rather than torture you with the details of everything I did that did not work, here is what finally did work. Export the Certificates from IE First, take the offending WSDL URL and paste it into IE (if you have an internal Microsoft CA, you have IE, even if you don’t use it in favor of some other browser). To state the semi-obvious, if you received the error above there is a certificate configured for the IIS host of the service and the SSL port has been configured properly. Otherwise there would be a different error, usually about the site not found or connection failed. Once the WSDL loads, to the right of the address bar there will be a lock icon. Click the lock and then click View Certificates in the resulting dialog (if you do not have a lock icon but do have a Certificate Error message, see http://support.microsoft.com/kb/931850 for steps to install the certificate then you can continue from the point of finding the lock icon). Figure 1: View Certificates in IE Next, select the Details tab in the resulting dialog Figure 2: Use Certificate Details to Export Certificate Click Copy to File, then Next, then select the Base-64 encoded option for the format Figure 3: Select the Base-64 encoded option for the format For the sake of simplicity, I choose to save this to the root of the WebLogic domain. It will work from anywhere, but later you will need to type in the full path rather than just the certificate name if you save it elsewhere. Figure 4: Browse to Save Location Figure 5: Save the Certificate to the Domain Root for Convenience This is the point where I ran into some confusion. Some articles mentioned exporting the entire chain of certificates. This supposedly works for some types of certificates, or if you have a few other tools and the time to learn them. For the SSL experts out there, they already have these tools, know how to use them well, and should not be wasting their time reading this article meant for folks who just want to get things wired up and back to unit testing and development. For the rest of us, the easiest way to make sure things will work is to just export all the links in the chain individually and let WebLogic Server worry about re-assembling them into a chain (which it does quite nicely). While perhaps not the most elegant solution, the multi-step process is easy to repeat and uses only tools that are immediately available and require no learning curve. So… Next, go to Tools then Internet Options then the Content tab and click Certificates. Go to the Trust Root Certificate Authorities tab and find the certificate root for your Microsoft CA cert (look for the Issuer of the certificate you exported earlier). Figure 6: Trusted Root Certification Authorities Tab Export this one the same way as before, with a different name Figure 7: Use a Unique Name for Each Certificate Repeat this once more for the Intermediate Certificate tab. Import the Certificates to the WebLogic Domain Now, open an command prompt, navigate to [WEBLOGIC_DOMAIN_ROOT]\bin and execute setDomainEnv. You should then be in the root of the domain. If not, CD to the domain root. Assuming you saved the certificate in the domain root, execute the following: keytool -importcert -alias [ALIAS-1] -trustcacerts -file [FULL PATH TO .CER 1] -keystore truststore.jks -storepass [PASSWORD] An example with the variables filled in is: keytool -importcert -alias IIS-1 -trustcacerts -file microsftcert.cer -keystore truststore.jks -storepass password After several lines out output you will be prompted with: Trust this certificate? [no]: The correct answer is ‘yes’ (minus the quotes, of course). You’ll you know you were successful if the response is: Certificate was added to keystore If not, check your typing, as that is generally the source of an error at this point. Repeat this for all three of the certificates you exported, changing the [ALIAS-1] and [FULL PATH TO .CER 1] value each time. For example: keytool -importcert -alias IIS-1 -trustcacerts -file microsftcert.cer -keystore truststore.jks -storepass password keytool -importcert -alias IIS-2 -trustcacerts -file microsftcertRoot.cer -keystore truststore.jks -storepass password keytool -importcert -alias IIS-3 -trustcacerts -file microsftcertIntermediate.cer -keystore truststore.jks -storepass password In the above we created a new JKS key store. You can re-use an existing one by changing the name of the JKS file to one you already have and change the password to the one that matches that JKS file. For the DemoTrust.jks  that is included with WebLogic the password is DemoTrustKeyStorePassPhrase. An example here would be: keytool -importcert -alias IIS-1 -trustcacerts -file microsoft.cer -keystore DemoTrust.jks -storepass DemoTrustKeyStorePassPhrase keytool -importcert -alias IIS-2 -trustcacerts -file microsoftRoot.cer -keystore DemoTrust.jks -storepass DemoTrustKeyStorePassPhrase keytool -importcert -alias IIS-2 -trustcacerts -file microsoftInter.cer -keystore DemoTrust.jks -storepass DemoTrustKeyStorePassPhrase Whichever keystore you use, you can check your work with: keytool -list -keystore truststore.jks -storepass password Where “truststore.jks” and “password” can be replaced appropriately if necessary. The output will look something like this: Figure 8: Output from keytool -list -keystore Update the WebLogic Keystore Configuration If you used an existing keystore rather than creating a new one, you can restart your WebLogic Server and skip the rest of this section. For those of us who created a new one because that is the instructions we found online… Next, we need to tell WebLogic to use the JKS file (truststore.jks) we just created. Log in to the WebLogic Server Administration Console and navigate to Servers > AdminServer > Configuration > Keystores. Scroll down to “Custom Trust Keystore:” and change the value to “truststore.jks” and the value of “Custom Trust Keystore Passphrase:” and “Confirm Custom Trust Keystore Passphrase:” to the password you used when earlier, then save your changes. You will get a nice message similar to the following: Figure 9: To Be Safe, Restart Anyways The “No restarts are necessary” is somewhat of an exaggeration. If you want to be able to use the keystore you may need restart the server(s). To save myself aggravation, I always do. Your mileage may vary. Conclusion That should get you there. If there are some erroneous steps included for your situation in particular, I will offer up a semi-apology as the process described above does not take long at all and if there is one step that could be dropped from it, is still much faster than trying to figure this out from other sources.

  Read the article

• SQL SERVER – Weekly Series – Memory Lane – #006

  - by pinaldave

  Here is the list of selected articles of SQLAuthority.com across all these years. Instead of just listing all the articles I have selected a few of my most favorite articles and have listed them here with additional notes below it. Let me know which one of the following is your favorite article from memory lane. 2006 This was my very first year of blogging so I was every day learning something new. As I have said many times, that blogging was never an intention. I had really not understood what exactly I am working on or beginning when I was beginning blogging in 2006. I had never knew that my life was going to change forever, once I started blogging. When I look back all of this year, I am happy that we are here together. 2007 IT Outsourcing to India – Top 10 Reasons Companies Outsource Outsourcing is about trust, collaboration and success. Helping other countries in need has been always the course of mankind, outsourcing is nothing different then that. With information technology and process improvements increasing the complexity, costs and skills required to accomplish routine tasks as well as challenging complex tasks, companies are outsourcing such tasks to providers who have the expertise to perform them at lower costs , with greater value and quality outcome. UDF – Remove Duplicate Chars From String This was a very interesting function I wrote in my early career. I am still using this function when I have to remove duplicate chars from strings. I have yet to come across a scenario where it does not work so I keep on using it till today. Please leave a comment if there is any better solution to this problem. FIX : Error : 3702 Cannot drop database because it is currently in use This is a very generic error when DROP Database is command is executed and the database is not dropped. The common mistake user is kept the connection open with this database and trying to drop the database. The database cannot be dropped if there is any other connection open along with it. It is always a good idea to take database in single user mode before dropping it. Here is the quick tutorial regarding how to bring the database in single user mode: Using T-SQL | Using SSMS. 2008 Install SQL Server 2008 – How to Upgrade to SQL Server 2008 – Installation Tutorial This was indeed one of the most popular articles in SQL Server 2008. Lots of people wanted to learn how to install SQL SErver 2008 but they were facing various issues while installation. I build this tutorial which becomes reference points for many. Default Collation of SQL Server 2008 What is the collation of SQL Server 2008 default installations? I often see this question confusing many experienced developers as well. Well the answer is in following image. Ahmedabad SQL Server User Group Meeting – November 2008 User group meetings are fun, now a days I am going to User Group meetings every week but there was a case when I have been just a beginner on this subject. The bug of the community was caught on me years ago when I started to present in Ahmedabad and Gandhinagar SQ LServer User Groups. 2009 Validate an XML document in TSQL using XSD My friend Jacob Sebastian wrote an excellent article on the subject XML and XSD. Because of the ‘eXtensible’ nature of XML (eXtensible Markup Language), often there is a requirement to restrict and validate the content of an XML document to a pre-defined structure and values. XSD (XML Schema Definition Language) is the W3C recommended language for describing and validating XML documents. SQL Server implements XSD as XML Schema Collections. Star Join Query Optimization At present, when queries are sent to very large databases, millions of rows are returned. Also the users have to go through extended query response times when joining multiple tables are involved with such queries. ‘Star Join Query Optimization’ is a new feature of SQL Server 2008 Enterprise Edition. This mechanism uses bitmap filtering for improving the performance of some types of queries by the effective retrieval of rows from fact tables. 2010 These puzzles are very interesting and intriguing – there was lots of interest on this subject. If you have free time this weekend. You may want to try them out. SQL SERVER – Challenge – Puzzle – Usage of FAST Hint (Solution)  SQL SERVER – Puzzle – Challenge – Error While Converting Money to Decimal (Solution)  SQL SERVER – Challenge – Puzzle – Why does RIGHT JOIN Exists (Open)  Additionally, I had great fun presenting SQL Server Performance Tuning seminar at fantastic locations in Hyderabad. Installing AdventeWorks Database This has been the most popular request I have received on my blog. Here is the quick video about how one can install AdventureWorks. 2011 Effect of SET NOCOUNT on @@ROWCOUNT There was an interesting incident once while I was presenting a session. I wrote a code and suddenly 10 hands went up in the air.  This was a bit surprise to me as I do not know why they all got alerted. I assumed that there should be something wrong with either project, screen or my display. However the real reason was very interesting – I suggest you read the complete blog post to understand this interesting scenario. Error: Deleting Offline Database and Creating the Same Name This is very interesting because once a user deletes the offline database the MDF and LDF file still exists and if the user attempts to create a new database with the same name it will give error. I found this very interesting and the blog explains the concept very quickly. Have you ever faced a similar situation? Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Memory Lane, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• SQL SERVER – Weekly Series – Memory Lane – #032

  - by Pinal Dave

  Here is the list of selected articles of SQLAuthority.com across all these years. Instead of just listing all the articles I have selected a few of my most favorite articles and have listed them here with additional notes below it. Let me know which one of the following is your favorite article from memory lane. 2007 Complete Series of Database Coding Standards and Guidelines SQL SERVER Database Coding Standards and Guidelines – Introduction SQL SERVER – Database Coding Standards and Guidelines – Part 1 SQL SERVER – Database Coding Standards and Guidelines – Part 2 SQL SERVER Database Coding Standards and Guidelines Complete List Download Explanation and Example – SELF JOIN When all of the data you require is contained within a single table, but data needed to extract is related to each other in the table itself. Examples of this type of data relate to Employee information, where the table may have both an Employee’s ID number for each record and also a field that displays the ID number of an Employee’s supervisor or manager. To retrieve the data tables are required to relate/join to itself. Insert Multiple Records Using One Insert Statement – Use of UNION ALL This is very interesting question I have received from new developer. How can I insert multiple values in table using only one insert? Now this is interesting question. When there are multiple records are to be inserted in the table following is the common way using T-SQL. Function to Display Current Week Date and Day – Weekly Calendar Straight blog post with script to find current week date and day based on the parameters passed in the function.  2008 In my beginning years, I have almost same confusion as many of the developer had in their earlier years. Here are two of the interesting question which I have attempted to answer in my early year. Even if you are experienced developer may be you will still like to read following two questions: Order Of Column In Index Order of Conditions in WHERE Clauses Example of DISTINCT in Aggregate Functions Have you ever used DISTINCT with the Aggregation Function? Here is a simple example about how users can do it. Create a Comma Delimited List Using SELECT Clause From Table Column Straight to script example where I explained how to do something easy and quickly. Compound Assignment Operators SQL SERVER 2008 has introduced new concept of Compound Assignment Operators. Compound Assignment Operators are available in many other programming languages for quite some time. Compound Assignment Operators is operator where variables are operated upon and assigned on the same line. PIVOT and UNPIVOT Table Examples Here is a very interesting question – the answer to the question can be YES or NO both. “If we PIVOT any table and UNPIVOT that table do we get our original table?” Read the blog post to get the explanation of the question above. 2009 What is Interim Table – Simple Definition of Interim Table The interim table is a table that is generated by joining two tables and not the final result table. In other words, when two tables are joined they create an interim table as resultset but the resultset is not final yet. It may be possible that more tables are about to join on the interim table, and more operations are still to be applied on that table (e.g. Order By, Having etc). Besides, it may be possible that there is no interim table; sometimes final table is what is generated when the query is run. 2010 Stored Procedure and Transactions If Stored Procedure is transactional then, it should roll back complete transactions when it encounters any errors. Well, that does not happen in this case, which proves that Stored Procedure does not only provide just the transactional feature to a batch of T-SQL. Generate Database Script for SQL Azure When talking about SQL Azure the most common complaint I hear is that the script generated from stand-along SQL Server database is not compatible with SQL Azure. This was true for some time for sure but not any more. If you have SQL Server 2008 R2 installed you can follow the guideline below to generate a script which is compatible with SQL Azure. Convert IN to EXISTS – Performance Talk It is NOT necessary that every time when IN is replaced by EXISTS it gives better performance. However, in our case listed above it does for sure give better performance. You can read about this subject in the associated blog post. Subquery or Join – Various Options – SQL Server Engine Knows the Best Every single time whenever there is a performance tuning exercise, I hear the conversation from developer where some prefer subquery and some prefer join. In this two part blog post, I explain the same in the detail with examples. Part 1 | Part 2 Merge Operations – Insert, Update, Delete in Single Execution MERGE is a new feature that provides an efficient way to do multiple DML operations. In earlier versions of SQL Server, we had to write separate statements to INSERT, UPDATE, or DELETE data based on certain conditions; however, at present, by using the MERGE statement, we can include the logic of such data changes in one statement that even checks when the data is matched and then just update it, and similarly, when the data is unmatched, it is inserted. 2011 Puzzle – Statistics are not updated but are Created Once Here is the quick scenario about my setup. Create Table Insert 1000 Records Check the Statistics Now insert 10 times more 10,000 indexes Check the Statistics – it will be NOT updated – WHY? Question to You – When to use Function and When to use Stored Procedure Personally, I believe that they are both different things - they cannot be compared. I can say, it will be like comparing apples and oranges. Each has its own unique use. However, they can be used interchangeably at many times and in real life (i.e., production environment). I have personally seen both of these being used interchangeably many times. This is the precise reason for asking this question. 2012 In year 2012 I had two interesting series ran on the blog. If there is no fun in learning, the learning becomes a burden. For the same reason, I had decided to build a three part quiz around SEQUENCE. The quiz was to identify the next value of the sequence. I encourage all of you to take part in this fun quiz. Guess the Next Value – Puzzle 1 Guess the Next Value – Puzzle 2 Guess the Next Value – Puzzle 3 Guess the Next Value – Puzzle 4 Simple Example to Configure Resource Governor – Introduction to Resource Governor Resource Governor is a feature which can manage SQL Server Workload and System Resource Consumption. We can limit the amount of CPU and memory consumption by limiting /governing /throttling on the SQL Server. If there are different workloads running on SQL Server and each of the workload needs different resources or when workloads are competing for resources with each other and affecting the performance of the whole server resource governor is a very important task. Tricks to Replace SELECT * with Column Names – SQL in Sixty Seconds #017 – Video  Retrieves unnecessary columns and increases network traffic When a new columns are added views needs to be refreshed manually Leads to usage of sub-optimal execution plan Uses clustered index in most of the cases instead of using optimal index It is difficult to debug SQL SERVER – Load Generator – Free Tool From CodePlex The best part of this SQL Server Load Generator is that users can run multiple simultaneous queries again SQL Server using different login account and different application name. The interface of the tool is extremely easy to use and very intuitive as well. A Puzzle – Swap Value of Column Without Case Statement Let us assume there is a single column in the table called Gender. The challenge is to write a single update statement which will flip or swap the value in the column. For example if the value in the gender column is ‘male’ swap it with ‘female’ and if the value is ‘female’ swap it with ‘male’. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Memory Lane, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Partner Blog Series: PwC Perspectives - "Is It Time for an Upgrade?"

  - by Tanu Sood

  Is your organization debating their next step with regard to Identity Management? While all the stakeholders are well aware that the one-size-fits-all doesn’t apply to identity management, just as true is the fact that no two identity management implementations are alike. Oracle’s recent release of Identity Governance Suite 11g Release 2 has innovative features such as a customizable user interface, shopping cart style request catalog and more. However, only a close look at the use cases can help you determine if and when an upgrade to the latest R2 release makes sense for your organization. This post will describe a few of the situations that PwC has helped our clients work through. “Should I be considering an upgrade?” If your organization has an existing identity management implementation, the questions below are a good start to assessing your current solution to see if you need to begin planning for an upgrade: Does the current solution scale and meet your projected identity management needs? Does the current solution have a customer-friendly user interface? Are you completely meeting your compliance objectives? Are you still using spreadsheets? Does the current solution have the features you need? Is your total cost of ownership in line with well-performing similar sized companies in your industry? Can your organization support your existing Identity solution? Is your current product based solution well positioned to support your organization's tactical and strategic direction? Existing Oracle IDM Customers: Several existing Oracle clients are looking to move to R2 in 2013. If your organization is on Sun Identity Manager (SIM) or Oracle Identity Manager (OIM) and if your current assessment suggests that you need to upgrade, you should strongly consider OIM 11gR2. Oracle provides upgrade paths to Oracle Identity Manager 11gR2 from SIM 7.x / 8.x as well as Oracle Identity Manager 10g / 11gR1. The following are some of the considerations for migration: Check the end of product support (for Sun or legacy OIM) schedule There are several new features available in R2 (including common Helpdesk scenarios, profiling of disconnected applications, increased scalability, custom connectors, browser-based UI configurations, portability of configurations during future upgrades, etc) Cost of ownership (for SIM customers)\ Customizations that need to be maintained during the upgrade Time/Cost to migrate now vs. waiting for next version If you are already on an older version of Oracle Identity Manager and actively maintaining your support contract with Oracle, you might be eligible for a free upgrade to OIM 11gR2. Check with your Oracle sales rep for more details. Existing IDM infrastructure in place: In the past year and half, we have seen a surge in IDM upgrades from non-Oracle infrastructure to Oracle. If your organization is looking to improve the end-user experience related to identity management functions, the shopping cart style access request model and browser based personalization features may come in handy. Additionally, organizations that have a large number of applications that include ecommerce, LDAP stores, databases, UNIX systems, mainframes as well as a high frequency of user identity changes and access requests will value the high scalability of the OIM reconciliation and provisioning engine. Furthermore, we have seen our clients like OIM's out of the box (OOB) support for multiple authoritative sources. For organizations looking to integrate applications that do not have an exposed API, the Generic Technology Connector framework supported by OIM will be helpful in quickly generating custom connector using OOB wizard. Similarly, organizations in need of not only flexible on-boarding of disconnected applications but also strict access management to these applications using approval flows will find the flexible disconnected application profiling feature an extremely useful tool that provides a high degree of time savings. Organizations looking to develop custom connectors for home grown or industry specific applications will likewise find that the Identity Connector Framework support in OIM allows them to build and test a custom connector independently before integrating it with OIM. Lastly, most of our clients considering an upgrade to OIM 11gR2 have also expressed interest in the browser based configuration feature that allows an administrator to quickly customize the user interface without adding any custom code. Better yet, code customizations, if any, made to the product are portable across the future upgrades which, is viewed as a big time and money saver by most of our clients. Below are some upgrade methodologies we adopt based on client priorities and the scale of implementation. For illustration purposes, we have assumed that the client is currently on Oracle Waveset (formerly Sun Identity Manager).   Integrated Deployment: The integrated deployment is typically where a client wants to split the implementation to where their current IDM is continuing to handle the front end workflows and OIM takes over the back office operations incrementally. Once all the back office operations are moved completely to OIM, the front end workflows are migrated to OIM. Parallel Deployment: This deployment is typically done where there can be a distinct line drawn between which functionality the platforms are supporting. For example the current IDM implementation is handling the password reset functionality while OIM takes over the access provisioning and RBAC functions. Cutover Deployment: A cutover deployment is typically recommended where a client has smaller less complex implementations and it makes sense to leverage the migration tools to move them over immediately. What does this mean for YOU? There are many variables to consider when making upgrade decisions. For most customers, there is no ‘easy’ button. Organizations looking to upgrade or considering a new vendor should start by doing a mapping of their requirements with product features. The recommended approach is to take stock of both the short term and long term objectives, understand product features, future roadmap, maturity and level of commitment from the R&D and build the implementation plan accordingly. As we said, in the beginning, there is no one-size-fits-all with Identity Management. So, arm yourself with the knowledge, engage in industry discussions, bring in business stakeholders and start building your implementation roadmap. In the next post we will discuss the best practices on R2 implementations. We will be covering the Do's and Don't's and share our thoughts on making implementations successful. Meet the Writers: Dharma Padala is a Director in the Advisory Security practice within PwC.  He has been implementing medium to large scale Identity Management solutions across multiple industries including utility, health care, entertainment, retail and financial sectors.   Dharma has 14 years of experience in delivering IT solutions out of which he has been implementing Identity Management solutions for the past 8 years. Scott MacDonald is a Director in the Advisory Security practice within PwC.  He has consulted for several clients across multiple industries including financial services, health care, automotive and retail.   Scott has 10 years of experience in delivering Identity Management solutions. John Misczak is a member of the Advisory Security practice within PwC.  He has experience implementing multiple Identity and Access Management solutions, specializing in Oracle Identity Manager and Business Process Engineering Language (BPEL). Praveen Krishna is a Manager in the Advisory Security practice within PwC.  Over the last decade Praveen has helped clients plan, architect and implement Oracle identity solutions across diverse industries.  His experience includes delivering security across diverse topics like network, infrastructure, application and data where he brings a holistic point of view to problem solving. Jenny (Xiao) Zhang is a member of the Advisory Security practice within PwC.  She has consulted across multiple industries including financial services, entertainment and retail. Jenny has three years of experience in delivering IT solutions out of which she has been implementing Identity Management solutions for the past one and a half years.

  Read the article

• NoSQL Java API for MySQL Cluster: Questions & Answers

  - by Mat Keep

  The MySQL Cluster engineering team recently ran a live webinar, available now on-demand demonstrating the ClusterJ and ClusterJPA NoSQL APIs for MySQL Cluster, and how these can be used in building real-time, high scale Java-based services that require continuous availability. Attendees asked a number of great questions during the webinar, and I thought it would be useful to share those here, so others are also able to learn more about the Java NoSQL APIs. First, a little bit about why we developed these APIs and why they are interesting to Java developers. ClusterJ and Cluster JPA ClusterJ is a Java interface to MySQL Cluster that provides either a static or dynamic domain object model, similar to the data model used by JDO, JPA, and Hibernate. A simple API gives users extremely high performance for common operations: insert, delete, update, and query. ClusterJPA works with ClusterJ to extend functionality, including - Persistent classes - Relationships - Joins in queries - Lazy loading - Table and index creation from object model By eliminating data transformations via SQL, users get lower data access latency and higher throughput. In addition, Java developers have a more natural programming method to directly manage their data, with a complete, feature-rich solution for Object/Relational Mapping. As a result, the development of Java applications is simplified with faster development cycles resulting in accelerated time to market for new services. MySQL Cluster offers multiple NoSQL APIs alongside Java: - Memcached for a persistent, high performance, write-scalable Key/Value store, - HTTP/REST via an Apache module - C++ via the NDB API for the lowest absolute latency. Developers can use SQL as well as NoSQL APIs for access to the same data set via multiple query patterns – from simple Primary Key lookups or inserts to complex cross-shard JOINs using Adaptive Query Localization Marrying NoSQL and SQL access to an ACID-compliant database offers developers a number of benefits. MySQL Cluster’s distributed, shared-nothing architecture with auto-sharding and real time performance makes it a great fit for workloads requiring high volume OLTP. Users also get the added flexibility of being able to run real-time analytics across the same OLTP data set for real-time business insight. OK – hopefully you now have a better idea of why ClusterJ and JPA are available. Now, for the Q&A. Q & A Q. Why would I use Connector/J vs. ClusterJ? A. Partly it's a question of whether you prefer to work with SQL (Connector/J) or objects (ClusterJ). Performance of ClusterJ will be better as there is no need to pass through the MySQL Server. A ClusterJ operation can only act on a single table (e.g. no joins) - ClusterJPA extends that capability Q. Can I mix different APIs (ie ClusterJ, Connector/J) in our application for different query types? A. Yes. You can mix and match all of the API types, SQL, JDBC, ODBC, ClusterJ, Memcached, REST, C++. They all access the exact same data in the data nodes. Update through one API and new data is instantly visible to all of the others. Q. How many TCP connections would a SessionFactory instance create for a cluster of 8 data nodes? A. SessionFactory has a connection to the mgmd (management node) but otherwise is just a vehicle to create Sessions. Without using connection pooling, a SessionFactory will have one connection open with each data node. Using optional connection pooling allows multiple connections from the SessionFactory to increase throughput. Q. Can you give details of how Cluster J optimizes sharding to enhance performance of distributed query processing? A. Each data node in a cluster runs a Transaction Coordinator (TC), which begins and ends the transaction, but also serves as a resource to operate on the result rows. While an API node (such as a ClusterJ process) can send queries to any TC/data node, there are performance gains if the TC is where most of the result data is stored. ClusterJ computes the shard (partition) key to choose the data node where the row resides as the TC. Q. What happens if we perform two primary key lookups within the same transaction? Are they sent to the data node in one transaction? A. ClusterJ will send identical PK lookups to the same data node. Q. How is distributed query processing handled by MySQL Cluster ? A. If the data is split between data nodes then all of the information will be transparently combined and passed back to the application. The session will connect to a data node - typically by hashing the primary key - which then interacts with its neighboring nodes to collect the data needed to fulfil the query. Q. Can I use Foreign Keys with MySQL Cluster A. Support for Foreign Keys is included in the MySQL Cluster 7.3 Early Access release Summary The NoSQL Java APIs are packaged with MySQL Cluster, available for download here so feel free to take them for a spin today! Key Resources MySQL Cluster on-line demo  MySQL ClusterJ and JPA On-demand webinar  MySQL ClusterJ and JPA documentation MySQL ClusterJ and JPA whitepaper and tutorial

  Read the article

• Day 4 - Game Sprites In Action

  - by dapostolov

  Yesterday I drew an image on the screen. Most exciting, but ... I spent more time blogging about it then actual coding. So this next little while I'm going to streamline my game and research and simply post key notes. Quick notes on the last session: The most important thing I wanted to point out were the following methods:           spriteBatch.Begin(SpriteBlendMode.AlphaBlend);           spriteBatch.Draw(sprite, position, Color.White);           spriteBatch.End(); The spriteBatch object is used to draw Textures and a 2D texture is called a Sprite A texture is generally an image, which is called an Asset in XNA The Draw Method in the Game1.cs is looped (until exit) and utilises the spriteBatch object to draw a Scene To begin drawing a Scene you call the Begin Method. To end a Scene you call the End Method. And to place an image on the Scene you call the Draw method. The most simple implementation of the draw method is:           spriteBatch.Draw(sprite, position, Color.White); 1) sprite - the 2D texture you loaded to draw 2) position - the 2d vector, a set of x & y coordinates 3) Color.White - the tint to apply to the texture, in this case, white light = nothing, nada, no tint. Game Sprites In Action! Today, I played around with Draw methods to get comfortable with their "quirks". The following is an example of the above draw method, but with more parameters available for us to use. Let's investigate!             spriteBatch.Draw(sprite, position2, null, Color.White, MathHelper.ToRadians(45.0f), new Vector2(sprite.Width / 2, sprite.Height / 2), 1.0F, SpriteEffects.None, 0.0F); The parameters (in order): 1) sprite  the texture to display 2) position2 the position on the screen / scene this can also be a rectangle 3) null the portion of the image to display within an image null = display full image this is generally used for animation strips / grids (more on this below) 4) Color.White Texture tinting White = no tint 5) MathHelper.ToRadians(45.0f) rotation of the object, in this case 45 degrees rotates from the set plotting point. 6) new Vector(0,0) the plotting point in this case the top left corner the image will rotate from the top left of the texture in the code above, the point is set to the middle of the image. 7) 1.0f Image scaling (1x) 8) SpriteEffects.None you can flip the image horizontally or vertically 9) 0.0f The z index of the image. 0 = closer, 1 behind? And playing around with different combinations I was able to come up with the following whacky display:   Checking off Yesterdays Intention List: learn game development terminology (in progress) - We learned sprite, scene, texture, and asset. how to place and position (rotate) a static image on the screen (completed) - The thing to note was, it's was in radians and I found a cool helper method to convert degrees into radians. Also, the image rotates from it's specified point. how to layer static images on the screen (completed) - I couldn't seem to get the zIndex working, but one things for sure, the order you draw the image in also determines how it is rendered on the screen. understand image scaling (in progress) - I'm not sure I have this fully covered, but for the most part plug a number in the scaling field and the image grows / shrinks accordingly. can we reuse images? (completed) - yes, I loaded one image and plotted the bugger all over the screen. understand how framerate is handled in XNA (in progress) - I hacked together some code to display the framerate each second. A framerate of 60 appears to be the standard. Interesting to note, the GameTime object does provide you with some cool timing capabilities, such as...is the game running slow? Need to investigate this down the road. how to display text , basic shapes, and colors on the screen (in progress) - i got text rendered on the screen, and i understand containing rectangles. However, I didn't display "shapes" & "colors" how to interact with an image (collision of user input?) (todo) how to animate an image and understand basic animation techniques (in progress) - I was able to create a stripe animation of numbers ranging from 1 - 4, each block was 40 x 40 pixles for a total stripe size of 160 x 40. Using the portion (source Rectangle) parameter, i limited this display to each section at varying intervals. It was interesting to note my first implementation animated at rocket speed. I then tried to create a smoother animation by limiting the redraw capacity, which seemed to work. I guess a little more research will have to be put into this for animating characters / scenes. how to detect colliding images or screen edges (todo) - but the rectangle object can detect collisions I believe. how to manipulate the image, lets say colors, stretching (in progress) - I haven't figured out how to modify a specific color to be another color, but the tinting parameter definately could be used. As for stretching, use the rectangle object as the positioning and the image will stretch to fit! how to focus on a segment of an image...like only displaying a frame on a film reel (completed) - as per basic animation techniques what's the best way to manage images (compression, storage, location, prevent artwork theft, etc.) (todo) Tomorrows Intention Tomorrow I am going to take a stab at rendering a game menu and from there I'm going to investigate how I can improve upon the code and techniques. Intention List: Render a menu, fancy or not Show the mouse cursor Hook up click event A basic animation of somesort Investigate image / menu techniques D.

  Read the article

• SUPINFO International University in Mauritius

  Since a while I'm considering to pick up my activities as a student and I'd like to get a degree in Computer Science. Personal motivation I mean after all this years as a professional software (and database) developer I have the personal urge to complete this part of my education. Having various certifications by Microsoft and being awarded as an Microsoft Most Valuable Professional (MVP) twice looks pretty awesome on a resume but having a "proper" degree would just complete my package. During the last couple of years I already got in touch with C-SAC (local business school with degree courses), the University of Mauritius and BCS, the Chartered Institute for IT to check the options to enroll as an experienced software developer. Quite frankly, it was kind of alienating to receive that feedback: Start from scratch! No seriously? Spending x amount of years to sit for courses that might be outdated and form part of your daily routine? Probably being in an awkward situation in which your professional expertise might exceed the lecturers knowledge? I don't know... but if that's path to walk... Well, then I might have to go for it. SUPINFO International University Some weeks ago I was contacted by the General Manager, Education Recruitment and Development of Medine Education Village, Yamal Matabudul, to have a chat on how the local IT scene, namely the Mauritius Software Craftsmanship Community (MSCC), could assist in their plans to promote their upcoming campus. Medine went into partnership with the French-based SUPINFO International University and Mauritius will be the 36th location world-wide for SUPINFO. Actually, the concept of SUPINFO is very likely to the common understanding of an apprenticeship in Germany. Not only does a student enroll into the programme but will also be placed into various internships as part of the curriculum. It's a big advantage in my opinion as the person stays in touch with the daily procedures and workflows in the real world of IT. Statements like "We just received a 'crash course' of information and learned new technology which is equivalent to 1.5 months of lectures at the university" wouldn't form part of the experience of such an education. Open Day at the Medine Education Village Last Saturday, Medine organised their Open Day and it was the official inauguration of the SUPINFO campus in Mauritius. It's now listed on their website, too - but be warned, the site is mainly in French language although the courses are all done in English. Not only was it a big opportunity to "hang out" on the campus of Medine but it was great to see the first professional partners for their internship programme, too. Oh, just for the records, IOS Indian Ocean Software Ltd. will also be among the future employers for SUPINFO students. More about that in an upcoming blog entry. Open Day at Medine Education Village - SUPINFO International University in Mauritius Mr Alick Mouriesse, President of SUPINFO, arrived the previous day and he gave all attendees a great overview of the roots of SUPINFO, the general development of the educational syllabus and their high emphasis on their partnerships with local IT companies in order to assist their students to get future jobs but also feel the heartbeat of technology live. Something which is completely missing in classic institutions of tertiary education in Computer Science. And since I was on tour with my children, as usual during weekends, he also talked about the outlook of having a SUPINFO campus in Mauritius. Apart from the close connection to IT companies and providing internships to students, SUPINFO clearly works on an international level. Meaning students of SUPINFO can move around the globe and can continue their studies seamlessly. For example, you might enroll for your first year in France, then continue to do 2nd and 3rd year in Canada or any other country with a SUPINFO campus to earn your bachelor degree, and then live and study in Mauritius for the next 2 years to achieve a Master degree. Having a chat with Dale Smith, Expand Technologies, after his interesting session on Technological Entrepreneurship - TechPreneur More questions by other craftsmen of the Mauritius Software Craftsmanship Community And of course, this concept works in any direction, giving Mauritian students a huge (!) opportunity to live, study and work abroad. And thanks to this, Medine already announced that there will be new facilities near Cascavelle to provide dormitories and other facilities to international students coming to our island. Awesome! Okay, but why SUPINFO? Well, coming back to my original statement - I'd like to get a degree in Computer Science - SUPINFO has a process called Validation of Acquired Experience (VAE) which is tailor-made for employees in the field of IT, and allows you to enroll in their course programme. I already got in touch with their online support chat but was only redirected to some FAQs on their website, unfortunately. So, during the Open Day I seized the opportunity to have an one-on-one conversation with Alick Mouriesse, and he clearly encouraged me to gather my certifications and working experience. SUPINFO does an individual evaluation prior to their assignment regarding course level, and hopefully my chances of getting some modules ahead of studies are looking better than compared to the other institutes. Don't get me wrong, I don't want to go down the easy route but why should someone sit for "Database 101" or "Principles of OOP" when applying and preaching database normalisation and practicing Clean Code Developer are like flesh and blood? Anyway, I'll be off to get my transcripts of certificates together with my course assignments from the old days at the university. Yes, I studied Applied Chemistry for a couple of years before intersecting into IT and software development particularly... ;-)

  Read the article

• Stumbling Through: Making a case for the K2 Case Management Framework

  I have recently attended a three-day training session on K2s Case Management Framework (CMF), a free framework built on top of K2s blackpearl workflow product, and I have come away with several different impressions for some of the different aspects of the framework.  Before we get into the details, what is the Case Management Framework?  It is essentially a suite of tools that, when used together, solve many common workflow scenarios.  The tool has been developed over time by K2 consultants that have realized they tend to solve the same problems over and over for various clients, so they attempted to package all of those common solutions into one framework.  Most of these common problems involve workflow process that arent necessarily direct and would tend to be difficult to model.  Such solutions could be achieved in blackpearl alone, but the workflows would be complex and difficult to follow and maintain over time.  CMF attempts to simplify such scenarios not so much by black-boxing the workflow processes, but by providing different points of entry to the processes allowing them to be simpler, moving the complexity to a middle layer.  It is not a solution in and of itself, development is still required to tie the pieces together. CMF is under continuous development, both a plus and a minus in that bugs are fixed quickly and features added regularly, but it may be difficult to know which versions are the most stable.  CMF is not an officially supported K2 product, which means you will not get technical support but you will get access to the source code. The example given of a business process that would fit well into CMF is that of a file cabinet, where each folder in said file cabinet is a case that contains all of the data associated with one complaint/customer/incident/etc. and various users can access that case at any time and take one of a set of pre-determined actions on it.  When I was given that example, my first thought was that any workflow I have ever developed in the past could be made to fit this model there must be more than just this model to help decide if CMF is the right solution.  As the training went on, we learned that one of the key features of CMF is SharePoint integration as each case gets a SharePoint site created for it, and there are a number of excellent web parts that can be used to design a portal for users to get at all the information on their cases.  While CMF does not require SharePoint, without it you will be missing out on a huge portion of functionality that CMF offers.  My opinion is that without SharePoint integration, you may as well write your workflows and other components the old fashioned way. When I heard that each case gets its own SharePoint site created for it, warning bells immediately went off in my head as I felt that depending on the data load, a CMF enabled solution could quickly overwhelm SharePoint with thousands of sites so we have yet another deciding factor for CMF:  Just how many cases will your solution be creating?  While it is not necessary to use the site-per-case model, it is one of the more useful parts of the framework.  Without it, you are losing a big chunk of what CMF has to offer. When it comes to developing on top of the Case Management Framework, it becomes a matter of configuring what makes up a case, what can be done to a case, where each action on a case should take the user, and then typing up actions to case statuses.  This last step is one that I immediately warmed up to, as just about every workflow Ive designed in the past needed some sort of mapping table to set the status of a work item based on the action being taken definitely one of those common solutions that it is good to see rolled up into a re-useable entity (and it gets a nice configuration UI to boot!).  This concept is a little different than traditional workflow design, in that you dont have to think of an end-to-end process around passing a case along a path, rather, you must envision the case as central object with workflow threads branching off of it and doing their own thing with the case data.  Certainly there can be certain workflow threads that get rather complex, but the idea is that they RELATE to the case, they dont BECOME the case (though it is still possible with action->status mappings to prevent certain actions in certain cases, so it isnt always a wide-open free for all of actions on a case). I realize that this description of the Case Management Framework merely scratches the surface on what the product actually can do, and I dont think Ive conclusively defined for what sort of business scenario you can make a case for Case Management Framework.  What I do hope to have accomplished with this post is to raise awareness of CMF there is a (free!) product out there that could potentially simplify a tangled workflow process and give (for free!) a very useful set of SharePoint web parts and a nice set of (free!) reports.  The best way to see if it will truly fit your needs is to give it a try did I mention it is FREE?  Er, ok, so it is free, but only obtainable at this time for K2 partnersDid you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• ISACA Webcast follow up: Managing High Risk Access and Compliance with a Platform Approach to Privileged Account Management

  - by Darin Pendergraft

  Last week we presented how Oracle Privileged Account Manager (OPAM) could be used to manage high risk, privileged accounts.  If you missed the webcast, here is a link to the replay: ISACA replay archive (NOTE: you will need to use Internet Explorer to view the archive) For those of you that did join us on the call, you will know that I only had a little bit of time for Q&A, and was only able to answer a few of the questions that came in.  So I wanted to devote this blog to answering the outstanding questions.  Here they are. 1. Can OPAM track admin or DBA activity details during a password check-out session? Oracle Audit Vault is monitoring these activities which can be correlated to check-out events. 2. How would OPAM handle simultaneous requests? OPAM can be configured to allow for shared passwords.  By default sharing is turned off. 3. How long are the passwords valid?  Are the admins required to manually check them in? Password expiration can be configured and set in the password policy according to your corporate standards.  You can specify if you want forced check-in or not. 4. Can 2-factor authentication be used with OPAM? Yes - 2-factor integration with OPAM is provided by integration with Oracle Access Manager, and Oracle Adaptive Access Manager. 5. How do you control access to OPAM to ensure that OPAM admins don't override the functionality to access privileged accounts? OPAM provides separation of duties by using Admin Roles to manage access to targets and privileged accounts and to control which operations admins can perform. 6. How and where are the passwords stored in OPAM? OPAM uses Oracle Platform Security Services (OPSS) Credential Store Framework (CSF) to securely store passwords.  This is the same system used by Oracle Applications. 7. Does OPAM support hierarchical/level based privileges?  Is the log maintained for independent review/audit? Yes. OPAM uses the Fusion Middleware (FMW) Audit Framework to store all OPAM related events in a dedicated audit database.  8. Does OPAM support emergency access in the case where approvers are not available until later? Yes.  OPAM can be configured to release a password under a "break-glass" emergency scenario. 9. Does OPAM work with AIX? Yes supported UNIX version are listed in the "certified component section" of the UNIX connector guide at:http://docs.oracle.com/cd/E22999_01/doc.111/e17694/intro.htm#autoId0 10. Does OPAM integrate with Sun Identity Manager? Yes.  OPAM can be integrated with SIM using the REST  APIs.  OPAM has direct integration with Oracle Identity Manager 11gR2. 11. Is OPAM available today and what does it cost? Yes.  OPAM is available now.  Ask your Oracle Account Manager for pricing. 12. Can OPAM be used in SAP environments? Yes, supported SAP version are listed in the "certified component section" of the SAP  connector guide here: http://docs.oracle.com/cd/E22999_01/doc.111/e25327/intro.htm#autoId0 13. How would this product integrate, if at all, with access to a particular field in the DB that need additional security such as SSN's? OPAM can work with DB Vault and DB Firewall to provide the fine grained access control for databases. 14. Is VM supported? As a deployment platform Oracle VM is supported. For further details about supported Virtualization Technologies see Oracle Fusion Middleware Supported System configurations here: http://www.oracle.com/technetwork/middleware/ias/downloads/fusion-certification-100350.html 15. Where did this (OPAM) technology come from? OPAM was built by Oracle Engineering. 16. Are all Linux flavors supported?  How about BSD? BSD is not supported. For supported UNIX version see the "certified component section" of the UNIX connector guide http://docs.oracle.com/cd/E22999_01/doc.111/e17694/intro.htm#autoId0 17. What happens if users don't check passwords in at the end of a work task? In OPAM a time frame can be defined how long a password can be checked out. The security admin can force a check-in at any given time. 18. is MySQL supported? Yes, supported DB version are listed in the "certified component section" of the DB connector guide here: http://docs.oracle.com/cd/E22999_01/doc.111/e28315/intro.htm#BABGJJHA 19. What happens when OPAM crashes and you need to use the password? OPAM can be configured for high availability, but if required, OPAM data can be backed up/recovered.  See the OPAM admin guide. 20. Is OPAM Standalone product or does it leverage other components from IDM? OPAM can be run stand-alone, but will also leverage other IDM components

  Read the article

• Great event : Microsoft Visual Studio 2010 Launch @ Microsoft TechEd Blore

  - by sathya

  Great event : Microsoft Visual Studio 2010 Launch @ Microsoft TechEd Blore   I was really excited on attending the day 1 of Microsoft TechEd 2010 in Bangalore. This is the first Teched that am attending. The event was really fun filled with lot of knowledge sharing sessions and lots of goodies and gifts by the partners Initially the Event Started by Murthy's Session. He explained about the Developers relating to the 5 elements of nature (Pancha Boothaas) 1. Fire - Passion 2. Wave (Water) - Catch the right wave which we need to apply. 3. Earth - Connections and lots of opportunities around the world 4. Air -  Its whatever we breathe. Developers.. Without them nothing is possible. they are like the air 5. Sky - Cloud based applications   Next the Keynote and the announcement of Visual Studio by SomaSegar. List of things that he delivered his speech on : 1. Announcement of Visual Studio 2010 2. Announcement of .NET 4.0 3. Announcement of Silverlight later this week 4. What is the current Trend? Microsoft has done a research with many developers across the globe and have got the following feedback from the users. Get Lost (interrupted) - When we do some work and somebody is calling or interrepting by someother way we lose track of what we were doing and we need to do from the start Falling Behind- Technology gets updated  phenomenally over a period of time and developers always have a scenario like they are not in the state of the art technology and they always have a doubt whether they are staying updated. Lack of Collobaration - When a Manager asks a person what the team members have done and some might be done and some might not be and finally all are into a state like we dont know where we are. So they have addressed these 3 points in the VS 2010 by the following features : Get Lost - Some cool features which could overcome this. We have some Graphical interface. which could show what we have done and where we are. Some Zoom features in the code level. Falling Behind - Everything is based on .NET language base. 2010 has been built in such a way that if developers know the native language that's enough for building good applications. Lack of Collobaration - Some Dashboard Features which would show where exactly the project is. And a graphical user interface is shown on clicking which it directly drills down even to the code level. 5. An overview on all new features in VS 2010. 6. Some good demos of new features in VS 2010 by Polita and one more girl. Some of the new features included : 1. Team Explorer 2. Zoom in Code 3. Ribbon Development 4. Development in Single Platform for Windows Phone, XBox, Zune, Azure, Web Based and Windows based applications 5. Sequence Diagram Generation directly from code 6. Dashboards to show project status 7. Javascript and JQuery intellisense 8. Native support for JQuery 9. Packaging feature while deploying. 10. Generation of different versions of web.config like Web.Config.Production, Web.Config.Staging, etc. 11. IntelliTrace - Eliminating the "Not Reproducible" statement. 12. Automated User Interface Testing. At last in the closing of the day we had a great event called Demo Extravaganza, where lot of cool projects that were launched by Microsoft and also the projects that are under research were also shown. I got a lot of info about Bing today. BING really rocks!!! It has the following : 1. Visual Search 2. Product based search. For each product different menu filters were provided to make an advanced search 3. BING Maps was awesome!! It zoomed in to the street level and we can assume that we are the persons who are walking or running on the road and we can see the real objects like buildings moving by our side. 4. PhotoSynth was used in BING to show up all the images taken around the globe in a 3D format. 5. Formula - If we give some formula it automatically gives the value for the variable or derivation of expression Also some info about some kool touch apps which does an authentication and computation of Teched Attendee's Points that they have scored and the sessions attended. One guy won an XBOX in lucky draw as a gift. There were lot of Partner Stalls like Accenture,Intel,Citrix,MicroFocus,Telerik,infragistics,Sapient etc. Some Offers were provided for us like 50% off on Certifications, 1 free Elearning Course, etc. Stay tuned!! Wil update you on other events too..

  Read the article

• PeopleSoft at Alliance 2012 Executive Forum

  - by John Webb

  Guest Posting From Rebekah Jackson This week I jointed over 4,800 Higher Ed and Public Sector customers and partners in Nashville at our annual Alliance conference.   I got lost easily in the hallways of the sprawling Gaylord Opryland Hotel. I carried the resort map with me, and I would still stand for several minutes at a very confusing junction, studying the map and the signage on the walls. Hallways led off in many directions, some with elevators going down here and stairs going up there. When I took a wrong turn I would instantly feel stuck, lose my bearings, and occasionally even have to send out a call for help.    It strikes me that the theme for the Executive Forum this year outlines a less tangible but equally disorienting set of challenges that our higher education customer’s CIOs are facing: Making Decisions at the Intersection of Business Value, Strategic Investment, and Enterprise Technology. The forces acting upon higher education institutions today are not neat, straight-forward decision points, where one can glance to the right, glance to the left, and then quickly choose the best course of action. The operational, technological, and strategic factors that must be considered are complex, interrelated, messy…and the stakes are high. Michael Horn, co-author of “Disrupting Class: How Disruptive Innovation Will Change the Way the World Learns”, set the tone for the day. He introduced the model of disruptive innovation, which grew out of the research he and his colleagues have done on ‘Why Successful Organizations Fail’. Highly simplified, the pattern he shared is that things start out decentralized, take a leap to extreme centralization, and then experience progressive decentralization. Using computers as an example, we started with a slide rule, then developed the computer which centralized in the form of mainframes, and gradually decentralized to mini-computers, desktop computers, laptops, and now mobile devices. According to Michael, you have more computing power in your cell phone than existed on the planet 60 years ago, or was on the first rocket that went to the moon. Applying this pattern to Higher Education means the introduction of expensive and prestigious private universities, followed by the advent of state schools, then by community colleges, and now online education. Michael shared statistics that indicate 50% of students will be taking at least one on line course by 2014…and by some measures, that’s already the case today. The implication is that technology moves from being the backbone of the campus, the IT department’s domain, and pushes into the academic core of the institution. Innovative programs are underway at many schools like Bellevue and BYU Idaho, joined by startups and disruptive new players like the Khan Academy.   This presents both threat and opportunity for higher education institutions, and means that IT decisions cannot afford to be disconnected from the institution’s strategic plan. Subsequent sessions explored this theme.    Theo Bosnak, from Attain, discussed the model they use for assessing the complete picture of an institution’s financial health. Compounding the issue are the dramatic trends occurring in technology and the vendors that provide it. Ovum analyst Nicole Engelbert, shared her insights next and suggested that incremental changes are no longer an option, instead fundamental changes are affecting the landscape of enterprise technology in higher ed.    Nicole closed with her recommendation that institutions focus on the trends in higher education with an eye towards the strategic requirements and business value first. Technology then is the enabler.   The last presentation of the day was from Tom Fisher, Sr. Vice President of Cloud Services at Oracle. Tom runs the delivery arm of the Cloud Services group, and shared his thoughts candidly about his experiences with cloud deployments as well as key issues around managing costs and security in cloud deployments. Okay, we’ve covered a lot of ground at this point, from financials planning, business strategy, and cloud computing, with the possibility that half of the institutions in the US might not be around in their current form 10 years from now. Did I forget to mention that was raised in the morning session? Seems a little hard to believe, and yet Michael Horn made a compelling point. Apparently 100 years ago, 8 of the top 10 education institutions in the world were German. Today, the leading German school is ranked somewhere in the 40’s or 50’s. What will the landscape be 100 years from now? Will there be an institution from China, India, or Brazil in the top 10? As Nicole suggested, maybe US parents will be sending their children to schools overseas much sooner, faced with the ever-increasing costs of a US based education. Will corporations begin to view skill-based certification from an online provider as a viable alternative to a 4 year degree from an accredited institution, fundamentally altering the education industry as we know it?

  Read the article

• C# Performance Pitfall – Interop Scenarios Change the Rules

  - by Reed

  C# and .NET, overall, really do have fantastic performance in my opinion.  That being said, the performance characteristics dramatically differ from native programming, and take some relearning if you’re used to doing performance optimization in most other languages, especially C, C++, and similar.  However, there are times when revisiting tricks learned in native code play a critical role in performance optimization in C#. I recently ran across a nasty scenario that illustrated to me how dangerous following any fixed rules for optimization can be… The rules in C# when optimizing code are very different than C or C++.  Often, they’re exactly backwards.  For example, in C and C++, lifting a variable out of loops in order to avoid memory allocations often can have huge advantages.  If some function within a call graph is allocating memory dynamically, and that gets called in a loop, it can dramatically slow down a routine. This can be a tricky bottleneck to track down, even with a profiler.  Looking at the memory allocation graph is usually the key for spotting this routine, as it’s often “hidden” deep in call graph.  For example, while optimizing some of my scientific routines, I ran into a situation where I had a loop similar to: for (i=0; i<numberToProcess; ++i) { // Do some work ProcessElement(element[i]); } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } This loop was at a fairly high level in the call graph, and often could take many hours to complete, depending on the input data.  As such, any performance optimization we could achieve would be greatly appreciated by our users. After a fair bit of profiling, I noticed that a couple of function calls down the call graph (inside of ProcessElement), there was some code that effectively was doing: // Allocate some data required DataStructure* data = new DataStructure(num); // Call into a subroutine that passed around and manipulated this data highly CallSubroutine(data); // Read and use some values from here double values = data->Foo; // Cleanup delete data; // ... return bar; Normally, if “DataStructure” was a simple data type, I could just allocate it on the stack.  However, it’s constructor, internally, allocated it’s own memory using new, so this wouldn’t eliminate the problem.  In this case, however, I could change the call signatures to allow the pointer to the data structure to be passed into ProcessElement and through the call graph, allowing the inner routine to reuse the same “data” memory instead of allocating.  At the highest level, my code effectively changed to something like: DataStructure* data = new DataStructure(numberToProcess); for (i=0; i<numberToProcess; ++i) { // Do some work ProcessElement(element[i], data); } delete data; Granted, this dramatically reduced the maintainability of the code, so it wasn’t something I wanted to do unless there was a significant benefit.  In this case, after profiling the new version, I found that it increased the overall performance dramatically – my main test case went from 35 minutes runtime down to 21 minutes.  This was such a significant improvement, I felt it was worth the reduction in maintainability. In C and C++, it’s generally a good idea (for performance) to: Reduce the number of memory allocations as much as possible, Use fewer, larger memory allocations instead of many smaller ones, and Allocate as high up the call stack as possible, and reuse memory I’ve seen many people try to make similar optimizations in C# code.  For good or bad, this is typically not a good idea.  The garbage collector in .NET completely changes the rules here. In C#, reallocating memory in a loop is not always a bad idea.  In this scenario, for example, I may have been much better off leaving the original code alone.  The reason for this is the garbage collector.  The GC in .NET is incredibly effective, and leaving the allocation deep inside the call stack has some huge advantages.  First and foremost, it tends to make the code more maintainable – passing around object references tends to couple the methods together more than necessary, and overall increase the complexity of the code.  This is something that should be avoided unless there is a significant reason.  Second, (unlike C and C++) memory allocation of a single object in C# is normally cheap and fast.  Finally, and most critically, there is a large advantage to having short lived objects.  If you lift a variable out of the loop and reuse the memory, its much more likely that object will get promoted to Gen1 (or worse, Gen2).  This can cause expensive compaction operations to be required, and also lead to (at least temporary) memory fragmentation as well as more costly collections later. As such, I’ve found that it’s often (though not always) faster to leave memory allocations where you’d naturally place them – deep inside of the call graph, inside of the loops.  This causes the objects to stay very short lived, which in turn increases the efficiency of the garbage collector, and can dramatically improve the overall performance of the routine as a whole. In C#, I tend to: Keep variable declarations in the tightest scope possible Declare and allocate objects at usage While this tends to cause some of the same goals (reducing unnecessary allocations, etc), the goal here is a bit different – it’s about keeping the objects rooted for as little time as possible in order to (attempt) to keep them completely in Gen0, or worst case, Gen1.  It also has the huge advantage of keeping the code very maintainable – objects are used and “released” as soon as possible, which keeps the code very clean.  It does, however, often have the side effect of causing more allocations to occur, but keeping the objects rooted for a much shorter time. Now – nowhere here am I suggesting that these rules are hard, fast rules that are always true.  That being said, my time spent optimizing over the years encourages me to naturally write code that follows the above guidelines, then profile and adjust as necessary.  In my current project, however, I ran across one of those nasty little pitfalls that’s something to keep in mind – interop changes the rules. In this case, I was dealing with an API that, internally, used some COM objects.  In this case, these COM objects were leading to native allocations (most likely C++) occurring in a loop deep in my call graph.  Even though I was writing nice, clean managed code, the normal managed code rules for performance no longer apply.  After profiling to find the bottleneck in my code, I realized that my inner loop, a innocuous looking block of C# code, was effectively causing a set of native memory allocations in every iteration.  This required going back to a “native programming” mindset for optimization.  Lifting these variables and reusing them took a 1:10 routine down to 0:20 – again, a very worthwhile improvement. Overall, the lessons here are: Always profile if you suspect a performance problem – don’t assume any rule is correct, or any code is efficient just because it looks like it should be Remember to check memory allocations when profiling, not just CPU cycles Interop scenarios often cause managed code to act very differently than “normal” managed code. Native code can be hidden very cleverly inside of managed wrappers

  Read the article

• Poner aplicaci&oacute;n Asp.Net en modo OFFLINE

  - by Jason Ulloa

  Una de las opciones que todo aplicación debería tener es el poder ponerse en modo OFFLINE para evitar el acceso de usuarios. Esto es completamente necesario cuando queremos realizar cambios a nuestra aplicación (cambiar algo, poner una actualización, etc) o a nuestra base de datos y evitarnos problemas con los usuarios que se encuentren logueados dentro de la aplicación en ese momento. Muchos ejemplos a través de la Web exponen la forma de realizar esta tarea utilizando dos técnicas: 1. La primera de ellas es utilizar el archivo App_Offline.htm sin embargo, esta técnica tiene un inconveniente. Y es que, una vez que hemos subido el archivo a nuestra aplicación esta se bloquea completamente y no tenemos forma de volver a ponerla ONLINE a menos que eliminemos el archivo. Es decir no podemos controlarla. 2. La segunda de ellas es el utilizar la etiqueta httpRuntime, pero nuevamente tenemos el mismo problema. Al habilitar el modo OFFLINE mediante esta etiqueta, tampoco podremos acceder a un modo de administración para cambiarla. Un ejemplo de la etiqueta httpRuntime <configuration> <system.web> <httpRuntime enable="false" /> </system.web> </configuration>   Tomando en cuenta lo anterior, lo mas optimo seria que podamos por medio de alguna pagina de administración colocar nuestro sitio en modo OFFLINE, pero manteniendo el acceso a la pagina de administración para poder volver a cambiar el valor que pondrá nuestra aplicación nuevamente en modo ONLINE. Para ello, utilizaremos el web.config de nuestra aplicación y una pequeña clase que se encargara de Leer y escribir los valores. Lo primero será, abrir nuestro web.config y definir dentro del appSettings dos nuevas KEY que contendrán los valores para el modo OFFLINE de nuestra aplicación: <appSettings> <add key="IsOffline" value="false" /> <add key="IsOfflineMessage" value="Sistema temporalmente no disponible por tareas de mantenimiento." /> </appSettings>   En las KEY anteriores tenemos el IsOffLine con value de false, esto es para indicarle a nuestra aplicación que actualmente su modo de funcionamiento es ONLINE, este valor será el que posteriormente cambiemos a TRUE para volver al modo OFFLINE. Nuestra segunda KEY (IsOfflineMessage) posee el value (Sistema temporalmente….) que será mostrado al usuario como un mensaje cuando el sitio este en modo OFFLINE. Una vez definidas nuestras dos KEY en el web.config, escribiremos una clase personalizada para leer y escribir los valores. Así que, agregamos un nuevo elemento de tipo clase al proyecto llamado SettingsRules y la definimos como Public. Está clase contendrá dos métodos, el primero será para leer los valores: public string readIsOnlineSettings(string sectionToRead) { Configuration cfg = WebConfigurationManager.OpenWebConfiguration(System.Web.Hosting.HostingEnvironment.ApplicationVirtualPath); KeyValueConfigurationElement isOnlineSettings = (KeyValueConfigurationElement)cfg.AppSettings.Settings[sectionToRead]; return isOnlineSettings.Value; }   El segundo método, será el encargado de escribir los nuevos valores al web.config public bool saveIsOnlineSettings(string sectionToWrite, string value) { bool succesFullySaved;   try { Configuration cfg = WebConfigurationManager.OpenWebConfiguration(System.Web.Hosting.HostingEnvironment.ApplicationVirtualPath); KeyValueConfigurationElement repositorySettings = (KeyValueConfigurationElement)cfg.AppSettings.Settings[sectionToWrite];   if (repositorySettings != null) { repositorySettings.Value = value; cfg.Save(ConfigurationSaveMode.Modified); } succesFullySaved = true; } catch (Exception) { succesFullySaved = false; } return succesFullySaved; }   Por último, definiremos en nuestra clase una región llamada instance, que contendrá un método encargado de devolver una instancia de la clase (esto para no tener que hacerlo luego) #region instance   private static SettingsRules m_instance;   // Properties public static SettingsRules Instance { get { if (m_instance == null) { m_instance = new SettingsRules(); } return m_instance; } }   #endregion instance   Con esto, nuestra clase principal esta completa. Así que pasaremos a la implementación de las páginas y el resto de código que completará la funcionalidad.   Para complementar la tarea del web.config utilizaremos el fabuloso GLOBAL.ASAX, este contendrá el código encargado de detectar si nuestra aplicación tiene el valor de ONLINE o OFFLINE y además de bloquear todas las paginas y directorios excepto el que le hayamos definido como administrador, esto para luego poder volver a configurar el sitio.   El evento del Global.Asax que utilizaremos será el Application_BeginRequest   protected void Application_BeginRequest(Object sender, EventArgs e) {   if (Convert.ToBoolean(SettingsRules.Instance.readIsOnlineSettings("IsOffline"))) {   string Virtual = Request.Path.Substring(0, Request.Path.LastIndexOf("/") + 1);   if (Virtual.ToLower().IndexOf("/admin/") == -1) { //We don't makes action, is admin section Server.Transfer("~/TemporarilyOfflineMessage.aspx"); }   } } La primer Línea del IF, verifica si el atributo del web.config es True o False, si es true toma la dirección WEB que se ha solicitado y la incluimos en un IF para verificar si corresponde a la Sección admin (está sección no es mas que un folder en nuestra aplicación llamado admin y puede ser cambiado a cualquier otro). Si el resultado de ese if es –1 quiere decir que no coincide, entonces, esa será la bandera que nos permitirá bloquear inmediatamente la pagina actual, transfiriendo al usuario a una pagina de mantenimiento. Ahora, en nuestra carpeta Admin crearemos una nueva pagina asp.net llamada OnlineSettings.aspx para actualizar y leer los datos del web.config y una pagina Default.aspx para pruebas. Nuestra página OnlineSettings tendrá dos pasos importantes: 1. Leer los datos actuales de configuración protected void Page_Load(object sender, EventArgs e) { if (!IsPostBack) { IsOffline.Checked = Convert.ToBoolean(mySettings.readIsOnlineSettings("IsOffline")); OfflineMessage.Text = mySettings.readIsOnlineSettings("IsOfflineMessage"); } }   2. Actualizar los datos con los nuevos valores. protected void UpdateButton_Click(object sender, EventArgs e) { string htmlMessage = OfflineMessage.Text.Replace(Environment.NewLine, "<br />");   // Update the Application variables Application.Lock(); if (IsOffline.Checked) { mySettings.saveIsOnlineSettings("IsOffline", "True"); mySettings.saveIsOnlineSettings("IsOfflineMessage", htmlMessage); } else { mySettings.saveIsOnlineSettings("IsOffline", "false"); mySettings.saveIsOnlineSettings("IsOfflineMessage", htmlMessage); }   Application.UnLock(); }   Por último en la raíz de la aplicación, crearemos una nueva página aspx llamada TemporarilyOfflineMessage.aspx que será la que se muestre cuando se bloquee la aplicación. Al final nuestra aplicación se vería algo así Página bloqueada Configuración del Bloqueo Y para terminar la aplicación de ejemplo

  Read the article

• IndyTechFest Recap

  - by Johnm

  The sun had yet to raise above the horizon on Saturday, May 22nd and I was traveling toward the location of the 2010 IndyTechFest. In my freshly awaken, and pre-coffee, state I reflected on the months that preceded this day and how quickly they slipped away. The big day had finally come and the morning dew glistened with a unique brightness that morning. What is this all about? For those who are unfamiliar with IndyTechFest, it is a regional conference held in Indianapolis and hosted by the Indianapolis .NET Developers Association (IndyNDA) and the Indianapolis Professional Association for SQL Server (IndyPASS).  The event presents multiple tracks and sessions covering subjects such as Business Intelligence,  Database Administration, .NET Development, SharePoint Development, Windows Mobile Development as well as non-Microsoft topics such as Lean and MongoDB. This year's event was the third hosting of IndyTechFest. No man is an island No event such as IndyTechFest is executed by a single person. My fellow co-founders, with their highly complementary skill sets and philanthropy make the process very enjoyable. Our amazing volunteers and their aid were indispensible. The generous financial support of our sponsors that made the event and fabulous prizes possible. The spectacular line up of speakers who came from near and far to donate their time and knowledge. Our beloved attendees who sacrificed the first sunny Saturday in weeks to expand their skill sets and network with their peers. We are deeply appreciative. Challenges in preparation With the preparation of any event comes challenges. It is these challenges that makes the process of planning an event so interesting. This year's largest challenge was the location of the event. In the past two years IndyTechFest was held at the Gene B. Glick Junior Achievement Center in Indianapolis. This facility has been the hub of the Indy technical community for many years. As the big day drew near, the facility's availability came into question due to some recent changes that had occurred with those who operated the facility. We began our search for an alternative option. Thankfully, the Marriott Indianapolis East was available, was very spacious and willing to work within the range of our budget. Within days of our event, the decision to move proved to be wise since the prior location had begun renovations to the interior. Whew! Always trust your gut. Every day it's getting better At the ending of each year, we huddle together, review the evaluations and identify an area in which the event could improve. This year's big opportunity for improvement resided in the prize give-away portion at the end of the day. In the 2008 event, admittedly, this portion was rather chaotic, rushed and disorganized. This year, we broke the drawing into two sections, of which each attendee received two tickets. The first ticket was a drawing for the mountain of books that were given away. The second ticket was a drawing for the big prizes, the 2 Xboxes, 3 laptops and iPad. We peppered the ticket drawings with gift card raffles and tossing t-shirts into the audience. If at first you don't succeed, try and try again Each year of IndyTechFest, we have offered a means for ad-hoc sessions or discussion groups to pop-up. To our disappointment it was something that never quite took off. We have always believed that this unique type of session was valuable and wanted to figure out a way to make it work for this year. A special thanks to Alan Stevens, who took on and facilitated the "open space" track and made it an official success. Share with your tweety When the attendee badges were designed we decided to place an emphasis on the attendee's Twitter account as well as the events hash-tag (#IndyTechFest) to encourage some real-time buzz during the day. At the host table we displayed a Twitter feed for all to enjoy. It was quite successful and encouraging use of social media. My badge was missing my Twitter account since it was recently changed. For those who care to follow my rather sparse tweets, my address is @johnnydata. Man, this is one long blog post! All in all it was a very successful event. It is always great to see new faces and meet old friends. The planning for the 2011 IndyTechFest will kick off very soon. We have more capacity for future growth and a truck full of great ideas. Stay tuned!

  Read the article

• CodePlex Daily Summary for Friday, August 22, 2014

  CodePlex Daily Summary for Friday, August 22, 2014Popular ReleasesQuickMon: Version 3.22: This release add two important changes. 1. Config variables at the monitor pack level (global to entire monitor pack for all Collectors) 2. The QuickMon (Windows) service now automatically reloads monitor packs that have been changed since it was started. This means you don't have to restart the service for changes to take effect.SSIS ReportGeneratorTask: ReportGenerator Task 1.8: New version of the SSIS Report Generator Task that supports SQL Server 2008, 2012 and 2014. In addition to minor bug fixes Multi-Value Parameters and Execution Information were integrated. The complete variable and parameter assignment is now a string and can be set dynamically.Corefig for Windows Server 2012 Core and Hyper-V Server 2012: Corefig 1.1.2 ISO: FixesUpdated Hyper-V scripts to use version 2 of the WMI tree. Updated the Hyper-V check for saved VM to look for the proper identifier. Fixed text issues with the licensing tab (thanks to briangw for rooting this problem out). EnhancementsNew (and improved) version number in Corefig.psd1.Outlook 2013 Backup Add-In: Outlook Backup Add-In 1.3: Changelog for new version: Added button in config-window to reset the last backup-time (this will trigger the backup after closing outlook) Minimum interval set to 0 (backup at each closing of outlook) Catch exception when data store entry is corrupt Added two parameters (prefix and suffix) to automatically rename the backup file Updated VSTO-Runtime to 10.0.50325 Upgraded project to Visual Studio 2013 Added optional command to run after backup (e.g. pack backup files, ...) Add...babelua: 1.6.7.0: V1.6.7.0 - 2014.8.21New feature: add a file search window ( ctrl+1 or ALT+L ), like The file search in VC Assistant; Stability improvement: performance improvement when BabeLua load/unload; performance improvement when debugger load lua files;File Explorer for WPF: FileExplorer3_20August2014: Please see Aug14 Update.Open NFe: RDI Open NFe 3.0 (alpha): Atualização para o layout 3.10 da NFe.ODBC Connect: v1.0: ODBC Connect executables for both 32bit and 64bit ODBC data sourcesMSSQL Deployment Tool: Microsoft SQL Deploy Tool v1.3.1: MicrosoftSqlDeployTool: v1.3.1.38348 What's changed? Update namespace and assembly name. Bug fixing.SharePoint 2013 Search Query Tool: SharePoint 2013 Search Query Tool v2.1: Layout improvements Bug fixes Stores auth method and user name Moved experimental settings to Advanced boxCtrlAltStudio Viewer: CtrlAltStudio Viewer 1.2.2.41183 Alpha: This alpha of the CtrlAltStudio Viewer provides some preliminary Oculus Rift DK2 support. For more details, see the release notes linked to below. Release notes: http://ctrlaltstudio.com/viewer/release-notes/1-2-2-41183-alpha Support info: http://ctrlaltstudio.com/viewer/support Privacy policy: http://ctrlaltstudio.com/viewer/privacy Disclaimer: This software is not provided or supported by Linden Lab, the makers of Second Life.HDD Guardian: HDD Guardian 0.6.1: New: package now include smartctl 6.3; Removed: standard notification e-mail. Now you have to set your mail server to send e-mail alerts; Bugfix: USB detection error; custom e-mail server settings issue; bottom panel displays a wrong ATA error count.VG-Ripper & PG-Ripper: VG-Ripper 2.9.62: changes NEW: Added Support for 'MadImage.org' links NEW: Added Support for 'ImgSpot.org' links NEW: Added Support for 'ImgClick.net' links NEW: Added Support for 'Imaaage.com' links NEW: Added Support for 'Image-Bugs.com' links NEW: Added Support for 'Pictomania.org' links NEW: Added Support for 'ImgDap.com' links NEW: Added Support for 'FileSpit.com' links FIXED: 'ImgSee.me' linksMagick.NET: Magick.NET 7.0.0.0001: Magick.NET linked with ImageMagick 7-Beta.CMake Tools for Visual Studio: CMake Tools for Visual Studio 1.2: This release adds the following new features and bug fixes from CMake Tools for Visual Studio 1.1: Added support for CMake 3.0. Added support for word completion. Added IntelliSense support for the CMAKEHOSTSYSTEM_INFORMATION command. Fixed syntax highlighting for tokens beginning with escape sequences. Fixed issue uninstalling CMake Tools for Visual Studio after Visual Studio has been uninstalled.GW2 Personal Assistant Overlay: GW2 Personal Assistant Overlay 1.1: Overview1.1 is the second 'stable' release of the GW2 Personal Assistant Overlay. This version includes just a couple of very minor features and some minor bug fixes. For details regarding installation, setup, and general use, see Documentation. Note: If you were using a previous version, you will probably want to copy over the following user settings files: GW2PAO.DungeonSettings.xml GW2PAO.EventSettings.xml GW2PAO.WvWSettings.xml GW2PAO.ZoneCompletionSettings.xml New FeaturesAdded new "No...Fluentx: Fluentx v1.5.3: Added few more extension methods.fastJSON: v2.1.2: 2.1.2 - bug fix circular referencesJPush.NET: JPush Server SDK 1.2.1 (For JPush V3): Assembly: 1.2.1.24728 JPush REST API Version: v3 JPush Documentation Reference .NET framework: v4.0 or above. Sample: class: JPushClientV3 2014 Augest 15th.SEToolbox: SEToolbox 01.043.008 Release 1: Changed ship/station names to use new DisplayName instead of Beacon/Antenna. Fixed issue with updated SE binaries 01.043.018 using new Voxel Material definitions.New Projects1thManage: GDT for erevery oneCreateProjectOnCodePlex: This is the first project for CoderCamps.HEAD FIRST C# LAB 1 : A DAY AT THE RACES: This has been provided for educational purposes and general discussion to improve coding practices associated with the resources detailed within Head First C#.Introduce Audit logging to your EF application using Repository & Unit of Work: Introduce Auditing in your application that uses Entity Framework by utilizing the Repository and Unit of Work design patterns.License Registration (C++): Allow to create demo version, activate or not a module.MS Word SharepointWiki Plugin: Scope of the Plugin is to enable a Post to a Sharepoint Wiki from within MS Word with Formatted Text and Images.Send My Zip: This app will help you to send the files were zipped then send the email about password information. This project is currently in setup mode and only availablewinhttp: this is a project for http/https download.Wix Builder: WixBuilder focusses on easily generating a WiX script from a project ouput, compile and link it into msi installer using the WiX Toolset.XiamiSig: ????????。

  Read the article

• Explaining Explain Plan Notes for Auto DOP

  - by jean-pierre.dijcks

  I've recently gotten some questions around "why do I not see a parallel plan" while Auto DOP is on (I think)...? It is probably worthwhile to quickly go over some of the ways to find out what Auto DOP was thinking. In general, there is no need to go tracing sessions and look under the hood. The thing to start with is to do an explain plan on your statement and to look at the parameter settings on the system. Parameter Settings to Look At First and foremost, make sure that parallel_degree_policy = AUTO. If you have that parameter set to LIMITED you will not have queuing and we will only do the auto magic if your objects are set to default parallel (so no degree specified). Next you want to look at the value of parallel_degree_limit. It is typically set to CPU, which in default settings equates to the Default DOP of the system. If you are testing Auto DOP itself and the impact it has on performance you may want to leave it at this CPU setting. If you are running concurrent statements you may want to give this some more thoughts. See here for more information. In general, do stick with either CPU or with a specific number. For now avoid the IO setting as I've seen some mixed results with that... In 11.2.0.2 you should also check that IO Calibrate has been run. Best to simply do a: SQL> select * from V$IO_CALIBRATION_STATUS; STATUS        CALIBRATION_TIME ------------- ---------------------------------------------------------------- READY         04-JAN-11 10.04.13.104 AM You should see that your IO Calibrate is READY and therefore Auto DOP is ready. In any case, if you did not run the IO Calibrate step you will get the following note in the explain plan: Note -----    - automatic DOP: skipped because of IO calibrate statistics are missing One more note on calibrate_io, if you do not have asynchronous IO enabled you will see:  ERROR at line 1: ORA-56708: Could not find any datafiles with asynchronous i/o capability ORA-06512: at "SYS.DBMS_RMIN", line 463 ORA-06512: at "SYS.DBMS_RESOURCE_MANAGER", line 1296 ORA-06512: at line 7 While this is changed in some fixes to the calibrate procedure, you should really consider switching asynchronous IO on for your data warehouse. Explain Plan Explanation To see the notes that are shown and explained here (and the above little snippet ) you can use a simple explain plan mechanism. There should  be no need to add +parallel etc. explain plan for <statement> SELECT PLAN_TABLE_OUTPUT FROM TABLE(DBMS_XPLAN.DISPLAY()); Auto DOP The note structure displaying why Auto DOP did not work (with the exception noted above on IO Calibrate) is like this: Automatic degree of parallelism is disabled: <reason> These are the reason codes: Parameter -  parallel_degree_policy = manual which will not allow Auto DOP to kick in  Hint - One of the following hints are used NOPARALLEL, PARALLEL(1), PARALLEL(MANUAL) Outline - A SQL outline of an older version (before 11.2) is used SQL property restriction - The statement type does not allow for parallel processing Rule-based mode - Instead of the Cost Based Optimizer the system is using the RBO Recursive SQL statement - The statement type does not allow for parallel processing pq disabled/pdml disabled/pddl disabled - For some reason (alter session?) parallelism is disabled Limited mode but no parallel objects referenced - your parallel_degree_policy = LIMITED and no objects in the statement are decorated with the default PARALLEL degree. In most cases all objects have a specific degree in which case Auto DOP will honor that degree. Parallel Degree Limited When Auto DOP does it works you may see the cap you imposed with parallel_degree_limit showing up in the note section of the explain plan: Note -----    - automatic DOP: Computed Degree of Parallelism is 16 because of degree limit This is an obvious indication that your are being capped for this statement. There is one quite interesting one that happens when you are being capped at DOP = 1. First of you get a serial plan and the note changes slightly in that it does not indicate it is being capped (we hope to update the note at some point in time to be more specific). It right now looks like this: Note -----    - automatic DOP: Computed Degree of Parallelism is 1 Dynamic Sampling With 11.2.0.2 you will start seeing another interesting change in parallel plans, and since we are talking about the note section here, I figured we throw this in for good measure. If we deem the parallel (!) statement complex enough, we will enact dynamic sampling on your query. This happens as long as you did not change the default for dynamic sampling on the system. The note looks like this: Note ----- - dynamic sampling used for this statement (level=5)

  Read the article

• A little primer on using TFS with a small team

  - by johndoucette

  The scenario; A small team of 3 developers mostly in maintenance mode with traditional ASP.net, classic ASP, .Net integration services and utilities with the company’s third party packages, and a bunch of java-based Coldfusion web applications all under Visual Source Safe (VSS). They are about to embark on a huge SharePoint 2010 new construction project and wanted to use subversion instead VSS. TFS was a foreign word and smelled of “high cost” and of an “over complicated process”. Since they had no preconditions about the old TFS versions (‘05 & ‘08), it was fun explaining how simple it was to install a TFS server and get the ball rolling, with or without all the heavy stuff one sometimes associates with such a huge and powerful application management lifecycle product. So, how does a small team begin using TFS? 1. Start by using source control and migrate current VSS source trees into TFS. You can take the latest version or migrate the entire version history. It’s up to you on whether you want a clean start or need quick access to all the version notes and history of the bits. 2. Since most shops are mainly in maintenance mode with existing applications, begin using bug workitems for everything. When you receive an issue/bug from your current tracking system, manually enter the workitem in TFS right through Visual Studio. You can automate the integration to the current tracking system later or replace it entirely. Believe me, this thing is powerful and can handle even the largest of help desks. 3. With new construction, begin work with requirements and task workitems and follow the traditional sprint-based development lifecycle. Obviously, some minor training will be needed, but don’t fear, this is very intuitive and MSDN has a ton of lesson based labs and videos. 4. For the java developers, use the new Team Explorer Everywhere 2010 plugin (recently known as Teamprise). There is a seamless interface in Eclipse, but also a good command-line utility for other environments such as Dreamweaver. 5. Wait to fully integrate the whole workitem/project management/testing process until your team is familiar with the integrated workitems for bugs and code. After a while, you will see the team wanting more transparency into the work they are all doing and naturally, everyone will want workitems to help them organize the chaos! 6. Management will be limited in the value of the reports until you have a fully blown implementation of project planning, construction, build, deployment and testing. However, there are some basic “bug rate” reports and current backlog listings that can provide good information. Some notable explanations of TFS; Work Item Tracking and Project Management - A workitem represents the unit of work within the system which enables tracking of all activities produced by a user, whether it is a developer, business user, project manager or tester. The properties of a workitem such as linked changesets (checked-in code), who updated the data and when, the states and reasons for change, are all transitioned to a data warehouse within TFS for reporting purposes. A workitem can be defines as a "bug", "requirement", test case", or a "change request". They drive the work effort by the individual assigned to it and also provide a key role in defining what needs to be done. Workitems are the things the team needs to do to accomplish a goal. Test Case Management - Starting with a workitem known as a "test case", a tester (or developer) can now author and manage test cases within a formal test plan subsystem. Although TFS supports the test case workitem type, there is a new product known as the VS Test Professional 2010 which allows a tester to facilitate manual tests including fast forwarding steps in the process to arrive at the assertion point quickly. This repeatable process provides quick regression tests and can be conducted by the business user to ensure completeness during UAT. In addition, developers no longer can provide a response to a bug with the line "cannot reproduce". With every test run, attachments including the recorded session, captured environment configurations and settings, screen shots, intellitrace (debugging history), and in some cases if the lab manager is being used, a snapshot of the tested environment is available. Version Control - A modern system allowing shared check-in/check-out, excellent merge conflict resolution, Shelvesets (personal check-ins), branching/merging visualization, public workspaces, gated check-ins, security hierarchy capabilities, and changeset/workitem tracking. Knowing what was done with the code by any developer has become much easier to picture and resolve issues. Team Build - Automate the compilation process whether you need it to be whenever a developer checks-in code, periodically such as nightly builds for testers in the morning, or manual builds to be deployed into production. Each build can run through pre-determined tests, perform code analysis to see if the developer conforms to the team standards, and reject the build if either fails. Project Portal & Reporting - Provide management with a dashboard with insight into the project(s). "Where are we" in each step of the way including past iterations and the current burndown rate. Enabling this feature is easy as it seamlessly interfaces with existing SharePoint implementations.

  Read the article

• JavaOne 2011: Content review process and Tips for submissions

  - by arungupta

  The Technical Sessions, Birds of Feather, Panels, and Hands-on labs (basically all the content delivered at JavaOne) forms the backbone of the conference. At this year's JavaOne conference you'll have access to the rock star speakers, the ability to engage with luminaries in the hallways, and have beer (or 2) with community peers in designated areas. Even though the conference is Oct 2-6, 2011, and will be bigger and better than last year's conference, the Call for Paper submission and review/selection evaluation started much earlier.In previous years, I've participated in the review process and this year I was honored to serve as co-lead for the "Enterprise Service Architecture and Cloud" track with Ludovic Champenois. We had a stellar review team with an equal mix of Oracle and external community reviewers. The review process is very overwhelming with the reviewers going through multiple voting iterations on each submission in order to ensure that the selected content is the BEST of the submitted lot. Our ultimate goal was to ensure that the content best represented the track, and most importantly would draw interest and excitement from attendees. As always, the number and quality of submissions were just superb, making for a truly challenging (and rewarding) experience for the reviewers. As co-lead I tried to ensure that I applied a fair and balanced process in the evaluation of content in my track. . Here are some key steps followed by all track leads: Vote on sessions - Each reviewer is required to vote on the sessions on a scale of 1-5 - and also provide a justifying comment. Create buckets - Divide the submissions into different buckets to ensure a fair representation of different topics within a track. This ensures that if a particular bucket got higher votes then the track is not exclusively skewed towards it. Top 7 - The review committee provides a list of the top 7 talks that can be used in the promotional material by the JavaOne team. Generally these talks are easy to identify and a consensus is reached upon them fairly quickly. First cut - Each track is allocated a total number of sessions (including panels), BoFs, and Hands-on labs that can be approved. The track leads then start creating the first cut of the approvals using the casted votes coupled with their prior experience in the subject matter. In our case, Ludo and I have been attending/speaking at JavaOne (and other popular Java-focused conferences) for double digit years. The Grind - The first cut is then refined and refined and refined using multiple selection criteria such as sorting on the bucket, speaker quality, topic popularity, cumulative vote total, and individual vote scale. The sessions that don't make the cut are reviewed again as well to ensure if they need to replace one of the selected one as a potential alternate. I would like to thank the entire Java community for all the submissions and many thanks to the reviewers who spent countless hours reading each abstract, voting on them, and helping us refine the list. I think approximately 3-4 hours cumulative were spent on each submission to reach an evaluation, specifically the border line cases. We gave our recommendations to the JavaOne Program Committee Chairperson (Sharat Chander) and accept/decline notifications should show up in submitter inboxes in the next few weeks. Here are some points to keep in mind when submitting a session to JavaOne next time: JavaOne is a technology-focused conference so any product, marketing or seemingly marketish talk are put at the bottom of the list.Oracle Open World and Oracle Develop are better options for submitting product specific talks. Make your title catchy. Remember the attendees are more likely to read the abstract if they like the title. We try our best to recategorize the talk to a different track if it needs to but please ensure that you are filing in the right track to have all the right eyeballs looking at it. Also, it does not hurt marking an alternate track if your talk meets the criteria. Make sure to coordinate within your team before the submission - multiple sessions from the same team or company does not ensure that the best speaker is picked. In such case we rely upon your "google presence" and/or review committee's prior knowledge of the speaker. The reviewers may not know you or your product at all and you get 750 characters to pitch your idea. Make sure to use all of them, to the last 750th character. Make sure to read your abstract multiple times to ensure that you are giving all the relevant information ? Think through your presentation and see if you are leaving out any important aspects.Also look if the abstract has any redundant information that will not required by the reviewers. There are additional sections that allow you to share information about the speaker and the presentation summary. Use them to blow the horn about yourself and any other relevant details. Please don't say "call me at xxx-xxx-xxxx to find out the details" :-) The review committee enjoyed reviewing the submissions and we certainly hope you'll have a great time attending them. Happy JavaOne!

  Read the article

• JavaOne 2011: Content review process and Tips for submissions

  - by arungupta

  The Technical Sessions, Birds of Feather, Panels, and Hands-on labs (basically all the content delivered at JavaOne) forms the backbone of the conference. At this year's JavaOne conference you'll have access to the rock star speakers, the ability to engage with luminaries in the hallways, and have beer (or 2) with community peers in designated areas. Even though the conference is Oct 2-6, 2011, and will be bigger and better than last year's conference, the Call for Paper submission and review/selection evaluation started much earlier.In previous years, I've participated in the review process and this year I was honored to serve as co-lead for the "Enterprise Service Architecture and Cloud" track with Ludovic Champenois. We had a stellar review team with an equal mix of Oracle and external community reviewers. The review process is very overwhelming with the reviewers going through multiple voting iterations on each submission in order to ensure that the selected content is the BEST of the submitted lot. Our ultimate goal was to ensure that the content best represented the track, and most importantly would draw interest and excitement from attendees. As always, the number and quality of submissions were just superb, making for a truly challenging (and rewarding) experience for the reviewers. As co-lead I tried to ensure that I applied a fair and balanced process in the evaluation of content in my track. . Here are some key steps followed by all track leads: Vote on sessions - Each reviewer is required to vote on the sessions on a scale of 1-5 - and also provide a justifying comment. Create buckets - Divide the submissions into different buckets to ensure a fair representation of different topics within a track. This ensures that if a particular bucket got higher votes then the track is not exclusively skewed towards it. Top 7 - The review committee provides a list of the top 7 talks that can be used in the promotional material by the JavaOne team. Generally these talks are easy to identify and a consensus is reached upon them fairly quickly. First cut - Each track is allocated a total number of sessions (including panels), BoFs, and Hands-on labs that can be approved. The track leads then start creating the first cut of the approvals using the casted votes coupled with their prior experience in the subject matter. In our case, Ludo and I have been attending/speaking at JavaOne (and other popular Java-focused conferences) for double digit years. The Grind - The first cut is then refined and refined and refined using multiple selection criteria such as sorting on the bucket, speaker quality, topic popularity, cumulative vote total, and individual vote scale. The sessions that don't make the cut are reviewed again as well to ensure if they need to replace one of the selected one as a potential alternate. I would like to thank the entire Java community for all the submissions and many thanks to the reviewers who spent countless hours reading each abstract, voting on them, and helping us refine the list. I think approximately 3-4 hours cumulative were spent on each submission to reach an evaluation, specifically the border line cases. We gave our recommendations to the JavaOne Program Committee Chairperson (Sharat Chander) and accept/decline notifications should show up in submitter inboxes in the next few weeks. Here are some points to keep in mind when submitting a session to JavaOne next time: JavaOne is a technology-focused conference so any product, marketing or seemingly marketish talk are put at the bottom of the list.Oracle Open World and Oracle Develop are better options for submitting product specific talks. Make your title catchy. Remember the attendees are more likely to read the abstract if they like the title. We try our best to recategorize the talk to a different track if it needs to but please ensure that you are filing in the right track to have all the right eyeballs looking at it. Also, it does not hurt marking an alternate track if your talk meets the criteria. Make sure to coordinate within your team before the submission - multiple sessions from the same team or company does not ensure that the best speaker is picked. In such case we rely upon your "google presence" and/or review committee's prior knowledge of the speaker. The reviewers may not know you or your product at all and you get 750 characters to pitch your idea. Make sure to use all of them, to the last 750th character. Make sure to read your abstract multiple times to ensure that you are giving all the relevant information ? Think through your presentation and see if you are leaving out any important aspects.Also look if the abstract has any redundant information that will not required by the reviewers. There are additional sections that allow you to share information about the speaker and the presentation summary. Use them to blow the horn about yourself and any other relevant details. Please don't say "call me at xxx-xxx-xxxx to find out the details" :-) The review committee enjoyed reviewing the submissions and we certainly hope you'll have a great time attending them. Happy JavaOne!

  Read the article

< Previous Page | 588 589 590 591 592 593 594 595 596 597 598 599  | Next Page >