Search Results

Search found 16182 results on 648 pages for 'event tracing'.

Page 595/648 | < Previous Page | 591 592 593 594 595 596 597 598 599 600 601 602  | Next Page >

• WinXP - Having trouble sharing internet with 3G USB modem via ICS

  - by Carlos Nunez

  all! I've been banging my head against a wall with this issue for a few days now and am hoping someone can help out. I recently signed up for T-Mobile's webConnect 3G/4G service to replace the faltering (and slow) DSL connection in my apartment. The goal was to put the SIM in one of my old phones and use its built-in WLAN tethering feature to share Internet out to rest of my computers. I quickly found out that webConnect-provisioned SIMs do not work with regular smartphones, so I was forced to either buy a 4G-compatible router or tether one of my old laptops to my wireless router and share out that way. I chose the latter, and it's sharpening my inner masochistic self by the day. Here's the setup: GSM USB modem (via hub), ICS host - 10/100 Mbps Ethernet NIC, ICS "guest" - WAN port of my SMC WGBR14N wireless router in bridged mode (i.e. wireless access point). Ideally, this would make my laptop the DHCP server and internet gateway with the WAP giving everyone wireless coverage. I can browse internet on the host laptop fine. However, when clients try to connect, they get a DHCP-assigned IP from the laptop and are able to use the Internet for a few minutes before completely dying. After that happens, they are able to re-associate with the WAP and get IP addresses, but are unable to use Internet or resolve IP addresses until the laptop and router are restarted. If they do get access, it's very, very slow. After running Wireshark on the host machine, it turns out that this is because every TCP connection keeps getting RST. DNS seems to work. I would normally think the firewall is the culprit here, but when it drops packets, it drops them completely. The fact that TCP connections are being ACK'ed by the destination rules that out. Of course, none of the event Log isn't saying anything about what's going on. I also tried disabling power management on the NIC, since that's caused problems in the past; that didn't help either. I finally disabled receive-side scaling as per a Microsoft KB (that applied to Windows Server 2003, SP2) to no avail. I'm thinking of trying it with a different NIC (will be tough; don't have a spare Ethernet NIC around for the laptop), but I'm getting the impression that this simply doesn't work. Can anyone please advise? I apologise for the length of this post; all contributions are much appreciated! -Carlos.

  Read the article

• CentOS 6 - Make system aware of custom lib paths and missing base links

  - by Mike Purcell

  I am trying to compile libmemcached (1.0.7) on CentOS6, and keep getting the following warning: ... checking for event.h... no configure: WARNING: Unable to find libevent ... I manually compiled libevent (2.0.19) and built it using the following configure line: OPTIONS="--prefix=/usr/local/_custom/app/libevent" Everything compiled and installed fine, but I couldn't figure out how to make the system aware that the lib files are in the custom /usr/local/_custom/app/libevent/libdir. I stumbled upon an article and read that I can make the system aware of custom lib paths by adding a custom file to /etc/ld.so.conf.d/ directory: # /etc/ld.so.conf.d/customApp.conf /usr/local/_custom/app/libevent/lib Then I issued the ldconfig command and was able to confirm that libevent was included by issuing this command: ldconfig -p | ack -i libevent Seeing that libevent was now included in the ldconfig output, I figured I would be able to compile libmemcached and satisfy the aforementioned warning. Unfortunately it did not. So I took another look at the ldconfig output and noticed this: libevent_pthreads-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_pthreads-2.0.so.5 libevent_openssl-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_openssl-2.0.so.5 libevent_extra-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_extra-2.0.so.5 libevent_core-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_core-2.0.so.5 libevent-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent-2.0.so.5 There are no references to the base links, for example, I would expect to see links to these (ls -la /usr/local/_custom/app/libevent/lib): libevent.so -> libevent-2.0.so.5.1.7 libevent_openssl.so -> libevent_openssl-2.0.so.5.1.7 libevent_core.so -> libevent_core-2.0.so.5.1.7 So either I am doing something wrong, or the system still does not know where to look to find libevent.so. -- Update #1 -- I wasn't able to get libmemcached to compile without the warning notice, even after trying to compile using the following configure command: ./configure --prefix=/usr/local/_custom/app/libmemcached CFLAGS="-I/usr/local/_custom/app/libevent/include" LDFLAGS="-L/usr/local/_custom/app/libevent/lib" I thought for sure this would work because I am directly passing the include and lib directories to the configure command. But it did not.

  Read the article

• Safer RAID5 rebuilds using partially failed disks?

  - by arcticmac

  There have been lots of articles posted recently about how RAID5 is dangerous because of long resilver times, and in particular because of increasing chances of encountering a URE during the resilver. Obviously this is a significant concern. However, it seems that in many cases of interest (as long as you're keeping some kind of eye on your disks), when it comes time to rebuild the array, the disk that I'm replacing is still mostly readable. If you try to explain this predicament to the average layperson, they are typically very confused as to why you have two almost completely functional disks but can't produce one working array. It seems to me that there ought to be some way to take advantage of this to make rebuilds safer, as long as I'm willing to have the RAID5 be read-only for a couple of days while it rebuilds. Conceptually, what I have in mind looks something like this: When a disk fails, immediately take the RAID5 offline or mount it read-only Attach a new disk (either in a spare bay, or externally via eSATA) and begin rebuilding it to replace the failed one. If known, perhaps start with the stripes in which the failure occurred, to minimize the chances of losing those if another disk fails. In the event that a second disk experiences a URE or other failure during the rebuild, try to source that data from the disk that is being replaced. Presumably if this happens, more rebuilding would be necessary. When complete, shut down the server, swap the replacement drive into the original bay if desired, and bring the array back up. Obviously such a process would not be appropriate for applications where uptime is critical or data loss cannot be tolerated, but it seems to me that this could help considerably to improve the reliability of RAID5. I assume that there's not a good way to implement a recovery like this at present, given that I haven't seen any indication of tools that are designed to do this, and that it seems like it would be rather obtuse to work out manually. Are there also technical issues with it that I haven't thought of (I'm still fairly new to RAID stuff)? Any thoughts on how hard something like this would be to implement (e.g. in linux md raid)?

  Read the article

• Forms authentication failed between web server and sql server

  - by Matt Bear

  I've actually found the solution, but I'm trying to understand why it failed, and why my solution fixed the problem. We have an application that uses forms authentication between a web server and sql server, web server runs server 2008, sql server runs 2008 r2, and sql server 2008. In august the sql server was patched with .net 3.5.1, the web server was untouched, and the forms authentication continued to work. 1 week ago we virtualized the web server onto our vSphere server because of failing hardware. Afterwards the form authentication failed with event code 4005, detail code 50201, The ticket supplied was invalid (on the sql server). In fact the sql server started generating Schannel errors and began blue screening 3-4 times a day. At this point I touched the sql server for the first time(ever), the errors were non specific, any reference to them I could find had to do with either zone alarm(which we don't run), or memory errors. So I applied service pack 1, which stopped the blue screening, but did not fix the forms authentication. At this point we had a work around, so we put it on the back burner while we completed another project, and I was able to get back on it last night. First thing was to adjust some code in the webconfig file on the sql server, nothing, next was regenerate and change out the machine key, still no change. Update the DNS servers, no change. Finally I went through and installed all windows updates, two reboots, (over RDP installed a network card driver which failed, and did not have my server room key, that was fun). After that, forms authentication was working again. And the sql server stopped generating as many errors, I've gotten two schannel errors since then. In short, forms authentication began failing when the web server was cloned onto a virtual machine, which caused the sql server to blue sceen? and forms authentication to fail. And could only be fixed by applying patches to the sql server?(I'm wishing I had patched the servers one at a time so I could know for sure which patch on which server fixed it). My question is why did it fail, and why did patching fix it? I hate fixing something without fully understanding the why and how.

  Read the article

• SSD Fresh Does Not Start

  - by Jim Fell

  I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fress from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried shutting down the Spybot Resident and disabling the firewall and virus scanner with no luck. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

  Read the article

• Hyper-V Machine drifts time all over, even with NTP

  - by MichaelGG

  Resolved The problem was Hyper-V on that machine. I removed Hyper-V, installed VMware Server, ran the same VM. Time sync issues went away (< 100ms difference after a day). My setup is like this: HYV1 - HyperV machine (non domain) - sync irrelevant AD1 - VM AD server on HYV1, sync'd to time.nist.gov. HyperV time sync off. S1 - Physical machine, sync'd to domain. S2 - Physical machine running HyperV, sync'd to domain. V1 - Linux VM machine on S2, sync'd to AD1. No HyperV integration. AD1 and S1 have fine sync -- stripchart shows less than 100ms difference. S2 drifts like crazy. Here's a bit of the stripchart against AD1: 18:33:22 d:+00.0010138s o:+05.4101899s 18:33:24 d:+00.0010138s o:+05.4319765s 18:33:26 d:+00.0000000s o:+05.4788429s 18:33:28 d:+00.0000000s o:+05.6089942s 18:33:30 d:+00.0010138s o:+05.7240269s 18:33:32 d:+00.0000000s o:+06.0421911s 18:33:34 d:+00.0081104s o:+06.5613708s 18:33:37 d:+00.0000000s o:+06.9096594s 18:33:39 d:+00.0000000s o:+06.8867838s 18:33:41 d:+00.0010127s o:+06.8936401s In 20 seconds, it drifted over a second. If I manually reset it to within 1s, within a few minutes it'll be back drifting about 2 seconds. Overnight it went from ~2s to ~5s. The Linux VM inside S2 has perfect sync with AD1. Here's the config: C:\Users\mgg>w32tm /dumpreg /subkey:Parameters Value Name Value Type Value Data ------------------------------------------------------------ ServiceDll REG_EXPAND_SZ %systemroot%\system32\w32time.dll ServiceMain REG_SZ SvchostEntry_W32Time ServiceDllUnloadOnStop REG_DWORD 1 Type REG_SZ NT5DS NtpServer REG_SZ ad01.mydomain ad02.mydomain C:\Users\mgg>w32tm /dumpreg /subkey:Config Value Name Value Type Value Data ----------------------------------------------------------- FrequencyCorrectRate REG_DWORD 4 PollAdjustFactor REG_DWORD 5 LargePhaseOffset REG_DWORD 50000000 SpikeWatchPeriod REG_DWORD 900 LocalClockDispersion REG_DWORD 9 HoldPeriod REG_DWORD 5 PhaseCorrectRate REG_DWORD 1 UpdateInterval REG_DWORD 30000 EventLogFlags REG_DWORD 2 AnnounceFlags REG_DWORD 5 TimeJumpAuditOffset REG_DWORD 28800 MinPollInterval REG_DWORD 2 MaxPollInterval REG_DWORD 8 MaxNegPhaseCorrection REG_DWORD -1 MaxPosPhaseCorrection REG_DWORD -1 MaxAllowedPhaseOffset REG_DWORD 300 I looked at the event log, and apart from warnings about sync (after it gets way out of sync), there's no other warnings. How can I go about troubleshooting this? It's the only machine that is having this problem. All the other machines (physical and virtual) are doing fine. Edit: To clarify: The VM (AD1) has integration turned off and syncs to time.nist.gov. AD1 is fine. It's the physical machine S1 that can't sync to AD1 and drifts all over. All the other physical servers are able to sync to AD1 just fine. Update So, it appears to be an issue of running the VM. The clock slips slowly with the VM off. Turned on, it immediately starts losing seconds. I swt the VM to only use half the resources, and that seems to have slightly mitigated it, for now. Thanks!

  Read the article

• Skyrim: Heavy Performance Issues after a couple of location changes

  - by Derija

  Okay, I've tried different solutions: ENB Series, removing certain mods, checking my FPS Rate, monitoring my resources, .ini tweaks. It's all just fine, I don't see what I'm missing. A couple of days ago, I bought Skyrim. Before I bought the game, I admit I had a pirated copy because my girlfriend actually wanted to buy me the game as a present, then said she didn't have enough money. Sick of waiting, I decided to buy the game by myself. The ridiculous part is, it worked better cracked than it does now uncracked. As the title suggests, after entering and leaving houses a couple of times, my performance obviously drops extremely. My build is just fine, Intel i5 quad core processor, NVIDIA GTX 560 Ti from Gigabyte, actually stock-OC, but manually downclocked to usual settings using appropriate Gigabyte software. This fixed the CTD issues I had before with both Skyrim and BF3. I have 4GB RAM. A website about Game Tweaks suggested that my HDD may be too slow. A screenshot of a Windows Performance Index sample with the subscription "This is likely to cause issues" showed the HDD with a performance index of 5.9, the exact same mine has, so I was playing with the thought to purchase an SSD instead, load games onto it that really need it like Skyrim, and hope it'd do the trick. Unfortunately, SSDs are likewise expensive, compared to "normal" HDDs... I'm really getting desperate about it. My save is gone because the patches made it impossible to load saves of the unpatched version and I already saved more than 80 times despite being only level 8, just because every time I interact with a door leading me to another location I'm scared the game will drop again. I can't even play for 30 mins straight anymore, it's just no fun at all. I've researched for a couple of days before I decided to post my question here. Any help is appreciated, I don't want to regret having bought the game... Since it actually is the best game I've played possibly for ever. Sincerely. P.S.: I don't think it's necessary to say, but still, of course I'm playing on PC. P.P.S.: After monitoring both my PC resources including CPU usage and HDD usage as well as the GPU usage, I don't see any changes even after the said event. P.P.P.S.: Original question posted here where I've been advised to ask here.

  Read the article

• Backing Up vs. Redundancy

  - by TK Kocheran

  I'm currently in stage 2 of 3 of building my home workstation. What this means is that my RAID-0 array of solid state disks will be backed up nightly to a RAID-5 or RAID-6 array of traditional spinning hard disks. However, it recently dawned on me that redundancy is not backup. The main reason for setting up a RAID array with redundancy was to protect myself in the event of a drive failure to serve as an effective backup solution. Wait. What if a bolt of lightning finds a way to travel into my house, through my surge-protector, into my power supply and physically destroys all of my hard disks and SSDs? Well, in that case, I guess I'd be fine because I generally keep most important files (music, pictures, videos) stored in multiple places like on my laptop, my wife's laptop, and an encrypted USB hard drive. Wait. What if a giant hedgehog meteor attacks my house from space traveling at mach 3 and all machines and hard disks are blown to smithereens. Well, I guess I could find a way to do ridiculously slow and cumbersome rsyncs or backups to Amazon's Glacier. Wait. What if there's a nuclear apocalypse... and at this point I start laughing hysterically. At what point does backing up become irrelevant? I completely understand situation one (mechanical drive failure), situation two (workstation compromised or destroyed somehow), possibly even situation three (all machines and disks destroyed), but situation four? There's no questioning the need for backups. None. However, there are three questions I'd really like addressed: To what level should one backup? I definitely understand the merits of physical disk redundancy. I also believe in keeping important files on multiple machines and thinning out the possibility of losing all of my files. Online backups make sense, but they beg the following question. What should I be backing up remotely and how often? It's no problem storage-wise to back up important files (music, pictures, videos) and even configuration and temporal data for all of the machines in my network (all Linux based)... albeit locally. Transferring to the cloud is another story. Worst-case scenario, if I lost all of my configuration for my individual computers, the reality is that I probably lost the machines too. The cloud is a long way away from here; I can run backups over CAT-6 here and see 100MB/s easily, but I'm afraid that I'm only going to see 2MB/s at best when transferring up to the cloud.

  Read the article

• Moving from single-site to multi-site Active Directory has broken OWA proxying

  - by messick

  Originally we had the following setup: OfficeExch01 has Mailbox Role and CAS Role OfficeExch01 is in the office. CoLoExch01 had just CAS Role. CoLoExch01 is internet facing and in a CoLo. Three AD domain controllers in the default site. Users could go to https://webmail.whatever.com/owa, get proxyed to OfficeExch01 and everything was great. Well, we recently setup a separate AD site and put a domain controller and the ColoExch01 server in the new site. I also made that remote DC be a Global Catalog. Now, users get the following error: Outlook Web Access is not available. If the problem continues, contact technical support for your organization and tell them the following: There is no Microsoft Exchange Client Access server that has the necessary configuration in the Active Directory site where the mailbox is stored. I also see event 41 errors in the logs: The Client Access server "https://webmail.xxxxxxx.com/owa" attempted to proxy Outlook Web Access traffic for mailbox "/o=XXXXX/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Recipients/cn=xxxxxxk". This failed because no Client Access server with an Outlook Web Access virtual directory configured for Kerberos authentication could be found in the Active Directory site of the mailbox. The simplest way to configure an Outlook Web Access virtual directory for Kerberos authentication is to set it to use Integrated Windows authentication by using the Set-OwaVirtualDirectory cmdlet in the Exchange Management Shell, or by using the Exchange Management Console. If you already have a Client Access server deployed in the target Active Directory site with an Outlook Web Access virtual directory configured for Kerberos authentication, the proxying Client Access server may not be finding that target Client Access server because it does not have an internalUrl parameter configured. You can configure the internalUrl parameter for the Outlook Web Access virtual directory on the Client Access server in the target Active Directory site by using the Set-OwaVirtualDirectory cmdlet. Looking this up I see a lot talk about ExternalURL and InternalURL settings. However, everything worked great until we made the new AD site. I also made sure the internal CAS server's /owa virtual directory is set to use Integrated Authentication. Is there something I need to do to allow Exchange to see that I've made these AD changes?

  Read the article

• Why is my new Phenom II 965 BE not significantly faster than my old Athlon 64 X2 4600+?

  - by Software Monkey

  I recently rebuilt my 5 year old computer. I upgraded all core components, in particular from an Athlon 64 X2 4600+ at 2.4 GHz with DDR2 800 to a Phenom II 965 BE (quad core) at 3.6 GHz with DDR3 1333 (actually 1600, but testing consistently detected memory errors at 1600). The motherboard is also much newer and better. The HDD's (x3), DVD writer and card reader are the same. The BIOS memory config is auto-everything except the base timing which I overrode to 1T instead of 2T. The BIOS CPU multiplier is slightly over-clocked to 3.6 GHz from the stock 3.4 GHz. I noticed compiling Java is slower than I expected. As it happens I have some (single-threaded) Java pattern-matching code which is CPU and memory bound and for which I have performance numbers recorded on a number of hardware platforms, including my old system. So I did a test run on the new equipment and was stunned to find that the numbers are only slightly better than my old system, about 25%. The data set it is operating on is a 148,975 character array, which should easily fit in caches, but in any event the new CPU has larger caches all around. The system was, of course, otherwise idle for the test and the test run is a timed 10 seconds to eliminate scheduling anomalies. A long while ago, when I upgraded only memory from DD2 667 to DDR2 800 there was no change in performance of this test, which subjectively supports that the test cycle does not need to (significantly) access main memory, but yes it is creating and garbage collecting a large number of objects in the process of this test (low millions of matches are found for the pattern set). I am about 99.999% certain the code hasn't changed since I last ran it on 2009-03-17 - but I can't easily retest the old hardware, because it is currently in pieces on my work-bench waiting to be built into a new computer for my kids. Note that Windows (XP) reports a CPU speed of 795 MHz unless I have some thing running. With stuff running it seems to jump all over the place each time I use ALT-Pause to display the system properties, everywhere from 795 MHz to 3.4 Ghz. So why might my shiny new hardware under-performing so badly? EDIT: The old memory was Mushkin DDR2 800 with timings set for auto which should have been 5-5-5-12. The new memory is Corsair DDR3 1600, running at 1333 with timings also auto which are 9-9-9-21. In both cases they are a paired set of dual channel DIMMs. I was waiting to ensure my system was stable before tweaking with memory timings.

  Read the article

• Write STDOUT & STDERR to a logfile, also write STDERR to screen

  - by Stefan Lasiewski

  I would like to run several commands, and capture all output to a logfile. I also want to print any errors to the screen (or optionally mail the output to someone). Here's an example. The following command will run three commands, and will write all output (STDOUT and STDERR) into a single logfile. { command1 && command2 && command3 ; } > logfile.log 2>&1 Here is what I want to do with the output of these commands: STDERR and STDOUT for all commands goes to a logfile, in case I need it later--- I usually won't look in here unless there are problems. Print STDERR to the screen (or optionally, pipe to /bin/mail), so that any error stands out and doesn't get ignored. It would be nice if the return codes were still usable, so that I could do some error handling. Maybe I want to send email if there was an error, like this: { command1 && command2 && command3 ; } logfile.log 2&1 || mailx -s "There was an error" [email protected] The problem I run into is that STDERR loses context during I/O redirection. A '2&1' will convert STDERR into STDOUT, and therefore I cannot view errors if I do 2 error.log Here are a couple juicier examples. Let's pretend that I am running some familiar build commands, but I don't want the entire build to stop just because of one error so I use the '--keep-going' flag. { ./configure && make --keep-going && make install ; } > build.log 2>&1 Or, here's a simple (And perhaps sloppy) build and deploy script, which will keep going in the event of an error. { ./configure && make --keep-going && make install && rsync -av --keep-going /foo devhost:/foo} > build-and-deploy.log 2>&1 I think what I want involves some sort of Bash I/O Redirection, but I can't figure this out.

  Read the article

• System Requirements of a write-heavy applications serving hundreds of requests per second

  - by Rolando Cruz

  NOTE: I am a self-taught PHP developer who has little to none experience managing web and database servers. I am about to write a web-based attendance system for a very large userbase. I expect around 1000 to 1500 users logged-in at the same time making at least 1 request every 10 seconds or so for a span of 30 minutes a day, 3 times a week. So it's more or less 100 requests per second, or at the very worst 1000 requests in a second (average of 16 concurrent requests? But it could be higher given the short timeframe that users will make these requests. crosses fingers to avoid 100 concurrent requests). I expect two types of transactions, a local (not referring to a local network) and a foreign transaction. local transactions basically download userdata in their locality and cache it for 1 - 2 weeks. Attendance equests will probably be two numeric strings only: userid and eventid. foreign transactions are for attendance of those do not belong in the current locality. This will pass in the following data instead: (numeric) locality_id, (string) full_name. Both requests are done in Ajax so no HTML data included, only JSON. Both type of requests expect at the very least a single numeric response from the server. I think there will be a 50-50 split on the frequency of local and foreign transactions, but there's only a few bytes of difference anyways in the sizes of these transactions. As of this moment the userid may only reach 6 digits and eventid are 4 to 5-digit integers too. I expect my users table to have at least 400k rows, and the event table to have as many as 10k rows, a locality table with at least 1500 rows, and my main attendance table to increase by 400k rows (based on the number of users in the users table) a day for 3 days a week (1.2M rows a week). For me, this sounds big. But is this really that big? Or can this be handled by a single server (not sure about the server specs yet since I'll probably avail of a VPS from ServInt or others)? I tried to read on multiple server setups Heatbeat, DRBD, master-slave setups. But I wonder if they're really necessary. the users table will add around 500 1k rows a week. If this can't be handled by a single server, then if I am to choose a MySQL replication topology, what would be the best setup for this case? Sorry, if I sound vague or the question is too wide. I just don't know what to ask or what do you want to know at this point.

  Read the article

• External USB HD issues with a twist (works on Windows7 but not XP)

  - by Eruditass

  I have this older external USB HD, 160 GB. I was using it to copy my Steam games to another computer. On the source computer, Windows 7 64-bit, everything worked fine. Drive reported no errors, had no hiccups, etc. Plugging it into the Windows XP 32-bit computer, it worked fine for looking through the files, moving files around on it (no real reading/writing, just modifying the filesystem table). However, when copying files from it to my internal HD, after a couple seconds to tens of minutes (seemingly random times), the USB device becomes unrecognized and it reports a delayed write error. Events in system log go like this, chronologically: (number times displayed)xSource (Event ID): "message" 2xdisk (51): An error was detected on device \Device\Harddisk1\D during a paging operation. 1xftdisk (57): The system failed to flush data to the transaction log. Corruption may occur. 1xApplication popup (26): Windows - Delayed Write Failed : Windows was unable to save all the data for the file E:\$Mft. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. 1xntfs (50): {Delayed Write Failed} Windows was unable to save all the data for the file . The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. These repeat for a while, then there is 10+ disk messages or ftdisk messages. Other notes: This occurs on random files at random times. This problem cannot be replicated on the Windows 7 source machine when copying from the HD to a different location on its local disk chkdsk /f was run and found no errors. chkdsk /f/r has the delayed write issue. drive was set to quick removal. Setting to performance in device manager yielded same result I am not writing anything to the USB external drive, so I am not sure why there is even a delayed write error (writing file access times?) local Windows XP was chkdsk'd without problems Windows XP machine has no problems with other USB HD's Various USB ports were attempted Rebooting did not help Occurs with SyncToy as well as windows explorer SMART status is good on both local drive and the external one Lack of gaming is making me cranky

  Read the article

• APC ups es 700 randomly overload

  - by Matteo Mosca

  First of all, I live in Italy, Europe, so keep this in mind for Volt/Watt considerations. Standard voltage in Italian apartments is 220V. In my living room I have 2 APC ups, one being an ES-550 and the other an ES-700 They each have 4 slots for surge protection only, and 4 slots for surge protection + battery backup. Just to give all the information, they both got their battery replaced less than one month ago. The ES-550 works fine, without any problem. On the battery I have connected: Pc Monitor Sony Bravia 46'' 4th slot is empty The ES-700 has the following on battery: Xbox 360 Ps3 (standby when not used) Wii (standby when not used) Netgear 8 port switch (always on) Here's what happens: the ES-700, randomly, but mostly at night when I'm sleeping, goes like "overload", with the constant beep. If I try to shut it off keeping the power button pressed, nothing happens. The only thing that works is unplugging random stuff (sometimes unplugging 1 console works, other times I have to unplug all 4 devices). Every time this happens the problem is "real", meaning the 4 devices become unpowered, so it's not just an "alarm no working properly" problem. While I'm sleeping, of course, the power usage is what described on the list, 2 devices on standy, 1 off and 1 on. Today it happened again while I was playing with my Ps3. I unplugged it, problem went away. I plugged it again, and it kept working fine. I just can't figure out what's the problem. The only additional info I can provide is that this behaviour started after a big power outage last december 26 (a blackout that lasted almost all day) but the "surge protection" part of those UPS should be there for those problems, to leverage peaks when power goes away or gets restored. Another funny thing is, althought it might not be related, for a couple of days after that event the Wii was unable to power on, I thought its power transformer was broken, but then it suddenly started working again. I can be sure it's not the Wii overloading the UPS because the overload happens even if I leave the Wii unplugged. Any suggestion is really appreciated, and I can provide any additional info, if needed, that didn't come to mind right now. Thanks.

  Read the article

• Do RAID controllers commonly have SATA drive brand compatibility issues?

  - by Jeff Atwood

  We've struggled with the RAID controller in our database server, a Lenovo ThinkServer RD120. It is a rebranded Adaptec that Lenovo / IBM dubs the ServeRAID 8k. We have patched this ServeRAID 8k up to the very latest and greatest: RAID bios version RAID backplane bios version Windows Server 2008 driver This RAID controller has had multiple critical BIOS updates even in the short 4 month time we've owned it, and the change history is just.. well, scary. We've tried both write-back and write-through strategies on the logical RAID drives. We still get intermittent I/O errors under heavy disk activity. They are not common, but serious when they happen, as they cause SQL Server 2008 I/O timeouts and sometimes failure of SQL connection pools. We were at the end of our rope troubleshooting this problem. Short of hardcore stuff like replacing the entire server, or replacing the RAID hardware, we were getting desperate. When I first got the server, I had a problem where drive bay #6 wasn't recognized. Switching out hard drives to a different brand, strangely, fixed this -- and updating the RAID BIOS (for the first of many times) fixed it permanently, so I was able to use the original "incompatible" drive in bay 6. On a hunch, I began to assume that the Western Digital SATA hard drives I chose were somehow incompatible with the ServeRAID 8k controller. Buying 6 new hard drives was one of the cheaper options on the table, so I went for 6 Hitachi (aka IBM, aka Lenovo) hard drives under the theory that an IBM/Lenovo RAID controller is more likely to work with the drives it's typically sold with. Looks like that hunch paid off -- we've been through three of our heaviest load days (mon,tue,wed) without a single I/O error of any kind. Prior to this we regularly had at least one I/O "event" in this time frame. It sure looks like switching brands of hard drive has fixed our intermittent RAID I/O problems! While I understand that IBM/Lenovo probably tests their RAID controller exclusively with their own brand of hard drives, I'm disturbed that a RAID controller would have such subtle I/O problems with particular brands of hard drives. So my question is, is this sort of SATA drive incompatibility common with RAID controllers? Are there some brands of drives that work better than others, or are "validated" against particular RAID controller? I had sort of assumed that all commodity SATA hard drives were alike and would work reasonably well in any given RAID controller (of sufficient quality).

  Read the article

• Remotely from Chrome or IE page loads ~60seconds, from Firefox or IE on local machine - instantly.

  - by Janis Veinbergs

  The problem: If i access SharePoint from Windows 7 with IE8 or Chrome5 - I must wait for like a minute to get a response. If i use other Windows 7 with IE8, just the same - just wait a MINUTE. If i use Firefox3.6 on W7 machine - page opens up instantly. Now switch to IE rendering engine in Firefox, you will have to wait just as with IE. Now i tried IE8 on XP SP3 - page opens up instantly. I tried IE8 on Windows Server 2003 SP2 (machine on which SharePoint is hosted) - page opens up instantly. IIS6 Logs I did request almost instantly from all 3 browsers and this is what shows up in IIS logs (first 2 entries for each browser): Chrome Ok, IIS saw first Chrome request when i Hit enter in browser, but i had to wait long for things to move on 2010-06-01 05:46:04 W3SVC1794621940 192.168.0.9 GET /sapulces - 80 - 192.168.0.186 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/533.4+(KHTML,+like+Gecko)+Chrome/5.0.375.55+Safari/533.4 401 2 2148074254 Loading... 2010-06-01 05:47:07 W3SVC1794621940 192.168.0.9 GET /sapulces - 80 - 192.168.0.186 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/533.4+(KHTML,+like+Gecko)+Chrome/5.0.375.55+Safari/533.4 401 1 0 ... etc... Firefox All Instantly 2010-06-01 05:46:06 W3SVC1794621940 192.168.0.9 GET /sapulces - 80 - 192.168.0.186 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+lv;+rv:1.9.2.3)+Gecko/20100401+Firefox/3.6.3 401 2 2148074254 2010-06-01 05:46:06 W3SVC1794621940 192.168.0.9 GET /sapulces - 80 - 192.168.0.186 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+lv;+rv:1.9.2.3)+Gecko/20100401+Firefox/3.6.3 401 1 0 ... etc... IE I did hit enter when it was 05:46:06, but these are first entries in IIS logs 2010-06-01 05:47:08 W3SVC1794621940 192.168.0.9 GET /sapulces - 80 - 192.168.0.186 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.1;+Trident/4.0;+SLCC2;+.NET+CLR+2.0.50727;+.NET+CLR+3.5.30729;+.NET+CLR+3.0.30729;+Media+Center+PC+6.0;+Tablet+PC+2.0;+.NET+CLR+1.1.4322;+.NET4.0C;+.NET4.0E) 401 1 0 2010-06-01 05:47:08 W3SVC1794621940 192.168.0.9 GET /sapulces - 80 - 192.168.0.186 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.1;+Trident/4.0;+SLCC2;+.NET+CLR+2.0.50727;+.NET+CLR+3.5.30729;+.NET+CLR+3.0.30729;+Media+Center+PC+6.0;+Tablet+PC+2.0;+.NET+CLR+1.1.4322;+.NET4.0C;+.NET4.0E) 401 1 0 ... etc... Nothing to see in Event Logs. The question Similar question has been asked but there is no response and i`m trying to access page without SSL and that happens even on GET requests. Where do I look? Where would be the problem? Browser? OS? I don't even know what to think about. Just a note Just a note about chrome's process isolation: I found it sad that while I was waiting that minute with Chrome, i could not use any other tab (i could switch, but i could not, for example, scroll or use any controls)

  Read the article

• Win7 x64 unresponsive for a minute or so. HD failing?

  - by Gaia

  On a fully updated Win7 x64, every so often the system stalls for a minute or so. This has been going on for a couple months now. By stalling I mean the mouse responds and I can move windows around, but any window, any program, that is open becomes whiteish when I select it AND any new programs will not open. It doesn't matter what kind of program it is. When the stall stops all clicks I made (open new programs for example) take effect. Nothing shows up consistently (as in every time this happens) in the event log. Today though I was able to find something, but it doesn't reveal much other than the "system was unresponsive". It's a 7009 for "A timeout was reached (30000 milliseconds) while waiting for the Windows Error Reporting Service service to connect." It doesn't matter if I have any USB devices plug-in or not. I've ran Microsoft Security Essentials and Malwarebytes. While the machine is unresponsive, I've noticed that Drive D (the other partition on the single internal HD in this laptop) is displayed like this in explorer. This never occurs with Drive C or any other drive on the machine. . SMART report for the physical drive: Read benchmark by HD Tune 5 Pro, probably the most telling piece of the puzzle. Isn't this alone enough to see there is a problem with the drive, regardless of whether the unresponsiveness is caused by such purported problem? Here is a short hardware report: Computer: LENOVO ThinkPad T520 CPU: Intel Core i5-2520M (Sandy Bridge-MB SV, J1) 2500 MHz (25.00x100.0) @ 797 MHz (8.00x99.7) Motherboard: LENOVO 423946U Chipset: Intel QM67 (Cougar Point) [B3] Memory: 8192 MBytes @ 664 MHz, 9.0-9-9-24 - 4096 MB PC10600 DDR3 SDRAM - Samsung M471B5273CH0-CH9 - 4096 MB PC10600 DDR3 SDRAM - Patriot Memory (PDP Systems) PSD34G13332S Graphics: Intel Sandy Bridge-MB GT2+ - Integrated Graphics Controller [D2/J1/Q0] [Lenovo] Intel HD Graphics 3000 (Sandy Bridge GT2+), 3937912 KB Drive: ST320LT007, 312.6 GB, Serial ATA 3Gb/s Sound: Intel Cougar Point PCH - High Definition Audio Controller [B2] Network: Intel 82579LM (Lewisville) Gigabit Ethernet Controller Network: Intel Centrino Advanced-N 6205 AGN 2x2 HMC OS: Microsoft Windows 7 Professional (x64) Build 7601 The drive less than 1 year old. Do I have a defective drive? Seagate Tools diag says there is nothing wrong with the drive... UPDATE: I noticed that the windows error reporting service entered the running state then the stopped state and the space between the two events was exactly 2 minutes. Which error it was trying to report I don't know. I check the "Reliability Monitor" and it shows no errors to be reported. I've disabled the windows error reporting service to see if the problem stops.

  Read the article

• Hyper-V causes boot loop/failure on a non-Gigabyte Win8 Pro system

  - by Nick

  Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated. EDIT: I found a collection of tips here.. http://social.msdn.microsoft.com/Forums/en-US/wptools/thread/b06cc9f2-aa5e-4cb3-9df1-0c273e1dfd68 So i've been attempting various bios settings to resolve this issue with no luck. I've tried setting 'CPUID Limit' to disabled. This seems to work partly as Win8 boots but no USB devices work at all. I also attempted disabling the usb 3.0 controller as the msdn topic lists an issue with USB controllers on Gigabyte boards. This also doesn't work. The USB devices light up but no input is received by the OS. All of my other bios CPU settings are in line with the info in the post. I'm totally stumped. Bios screenshots: http://i.imgur.com/yKN5u.png http://i.imgur.com/Y9wI4.png http://i.imgur.com/F6EuO.png

  Read the article

• Tomcat and IIS 7 both on different ip's and different ports

  - by n00b

  I have Tomcat and IIS 7 installed together on a Windows 2008 server. The machine has two IPs (134.133.1.1 and 134.133.2.2). I want Tomcat to handle 134.133.1.1, on port 80, and IIS to handle both 134.133.2.2, on port 80 AND 134.133.1.1, on port 443, but can't seem to get the last two together (I can get one or the other by themselves on IIS, along with the first IP address on Tomcat). I have configured Tomcat to successfully listen to ip 134.133.1.1, on port 80 with this configuration; <Connector port="80" protocol="HTTP/1.1" address="134.133.1.1" connectionTimeout="20000" redirectPort="8443" /> I also have a site configured in IIS bound to ip 134.133.1.1, on port 443 (SSL). When I turn on IIS, after Tomcat, I can reach both 134.133.1.1:80 (Tomcat) and 134.133.1.1:443 (IIS) successfully (as desired). The problem now comes when I want to introduce a new site via IIS, at the new ip address. In IIS I have setup a new site at IP 134.133.2.2, port 80. I can not start the site. The event log shows this error; Unable to bind to the underlying transport for [::]:80. The IP Listen-Only list may contain a reference to an interface which may not exist on this machine. The data field contains the error number. I think this is because IIS 7 tries to listen to port 80 on all IPs, and it cant because Tomcat is taking port 80 for 134.133.1.1. From reading, the resolution is to specify the IP address you want IIS to bind on port 80. The problem is, when I add 134.133.2.2 to the iplisten list, then I get a 404 when I try navigating to 134.133.1.1:443. I assume this is because IIS is no longer listening to ANY port on 134.133.1.1. How do I resolve this such that IIS will return both sites? EDIT: Per request my IIS binding for site A is 134.133.2.2 on port 80 (http) and 134.133.2.2 on port 443. For site B in IIS, the binding is 134.133.1.1 on port 443 (https). Note the IPs in this example are just for example purposes, but consistent with my setup.

  Read the article

• PTR Record Troubles

  - by Physikal

  I am having a hell of a time getting our PTR record right. Our current PTR zone looks like this: $ttl 38400 @ IN SOA ns1.domain.com. admin.domain.com. ( 1268669139 10800 3600 604800 38400 ) xxx.xxx.xxx.in-addr.arpa. IN NS ns2.domain.com. xxx.xxx.xxx.in-addr.arpa. IN NS ns1.domain.com. 97 IN PTR mail.domain.com. xxx.xxx.xxx.xxx.in-addr.arpa. IN PTR mail.domain.com. 97.96/28. IN PTR mail.domain.com For some reason the only thing that works is the 97.96/28. When this line is in there it actually says I have a PTR record when reporting from intodns.com. If I remove that line, it says I have no PTR. I have followed instructions from http://www.philchen.com/2007/04/04/configuring-reverse-dns and when I follow those instructions intodns.com says I have no PTR. When it does work with the line 97.96/28., the PTR kicks back as (from intodns.com) : 97.xxx.xxx.xxx.in-addr.arpa -> mail.domain.com.xxx.xxx.xxx.in-addr.arpa Which is, to my knowledge, an incorrect PTR. I want it to just kick back as mail.domain.com, without the xxx.xxx.xxx.in-addr.arpa extension. I have tried everything I can think of but I can't fix it. I can't help but think it's one of those things that is so stupid and simple I'm going to do the ol'facepalm. Any help is greatly appreciated. Thanks! In the event that the domain zone is needed, here it is: $ttl 38400 @ IN SOA domain.com. [email protected]. ( 1265221037 10800 3600 604800 38400 ) domain.com. IN A xxx.xxx.xxx.xxx www.domain.com. IN A xxx.xxx.xxx.xxx ftp.domain.com. IN A xxx.xxx.xxx.xxx m.domain.com. IN A xxx.xxx.xxx.xxx localhost.domain.com. IN A 127.0.0.1 webmail.domain.com. IN A xxx.xxx.xxx.xxx admin.domain.com. IN A xxx.xxx.xxx.xxx mail.domain.com. IN A xxx.xxx.xxx.xxx domain.com. IN MX 5 mail.domain.com. domain.com. IN TXT "v=spf1 a mx a:domain.com ip4:xxx.xxx.xxx.xxx ?all" domain.com. IN NS ns1 domain.com. IN NS ns2 ns1 IN A xxx.xxx.xxx.xxx ns2 IN A xxx.xxx.xxx.xxx Any double entries in different formats were part of my troubleshooting process.

  Read the article

• php-fpm or nginx: bad gateway

  - by John Tate

  I'm getting a bad gateway error all the sudden for a site. I didn't change the configuration for the site, I just added a new server config where I put them under /etc/nginx/servers and it stopped working. The new server works, and there is no conflict between the php-fpm listen addresses. server { listen 80; server_name obfuscated.onion; location = / { root /var/www/sites/obfuse; index index.php; } location / { root /var/www/sites/obfuse; index index.php; if (!-f $request_filename) { rewrite ^(.*)$ /index.php?q=$1 last; break; } if (!-d $request_filename) { rewrite ^(.*)$ /index.php?q=$1 last; break; } } error_page 404 /index.php; location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico)$ { root /var/www/sites/obfuse; access_log off; expires 30d; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/sites/obfuse$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param PATH_INFO $fastcgi_script_name; include fastcgi_params; } } There is nothing unusual in php-fpm's log even when I raised the level to debug. [24-Jun-2013 09:10:37.357943] DEBUG: pid 6756, fpm_scoreboard_init_main(), line 40: got clock tick '100' [24-Jun-2013 09:10:37.358950] DEBUG: pid 6756, fpm_event_init_main(), line 333: event module is kqueue and 1 fds have been reserved [24-Jun-2013 09:10:37.358978] NOTICE: pid 6756, fpm_init(), line 83: fpm is running, pid 6756 [24-Jun-2013 09:10:37.359009] DEBUG: pid 6756, main(), line 1832: Sending "1" (OK) to parent via fd=5 [24-Jun-2013 09:10:37.389215] DEBUG: pid 6756, fpm_children_make(), line 421: [pool cyruserv] child 22288 started [24-Jun-2013 09:10:37.391343] DEBUG: pid 6756, fpm_children_make(), line 421: [pool cyruserv] child 21911 started [24-Jun-2013 09:10:37.391914] DEBUG: pid 6756, fpm_event_loop(), line 362: 5776 bytes have been reserved in SHM [24-Jun-2013 09:10:37.391941] NOTICE: pid 6756, fpm_event_loop(), line 363: ready to handle connections [24-Jun-2013 09:10:38.393048] DEBUG: pid 6756, fpm_pctl_perform_idle_server_maintenance(), line 379: [pool cyruserv] currently 0 active children, 2 spare children, 2 running children. Spawning rate 1 [24-Jun-2013 09:10:39.403032] DEBUG: pid 6756, fpm_pctl_perform_idle_server_maintenance(), line 379: [pool cyruserv] currently 0 active children, 2 spare children, 2 running children. Spawning rate 1 [24-Jun-2013 09:10:40.413070] DEBUG: pid 6756, fpm_pctl_perform_idle_server_maintenance(), line 379: [pool cyruserv] currently 0 active children, 2 spare children, 2 running children. Spawning rate 1 I don't know why this has started happening, but the logs are not telling me anything. Please ask for more information than this, you'll probably need it.

  Read the article

• Windows 2003 Storage Server Hanging on Large File Transfers

  - by user25272

  In one of our offices we have a Dell PowerVault 745N NAS device which acts as the main file server. Its running 32bit Windows 2003 Storage Server SP2 with 3GB RAM. The server holds around 60 users HOME folders, which are mapped via AD. The office clients are a mix of XP SP3, Vista and Windows 7. Occasionally the server will completely hang when transferring large files. When the hang happens the console becomes unresponsive with only the mouse active and blank wallpaper. Sometimes stopping the copy frees the server, sometimes not. The hanging can last around 20 minutes. During this time other servers also become unresponsive with blank wallpaper at the console. If you do manage to get onto another server the taskbar and run commands are unresponsive. This also transcends to the client computers sometimes with explorer crashing. I'm guessing this is due to the HOME folder mapping. Eventually the NAS server with free up and everything will be back to normal. The server is configured as follows: PERC 4/DC DATA 2 - 12 SCSI HDD - RAID5 SHADOWCOPY 2 SCSI HDD - RAID1 CERC SATA DATA 11 4 SATA HDD - RAID5 OS 4 SATA HDD - RAID5 All the drivers and firmware is up to date. I've been through all the diagnostics with Dell and the hardware has come up clean including full HDD tests on the arrays. The server has NOD32 installed as the AV, but the hanging happens when it is uninstalled. There are no errors in the event log when this happens and we don't have any errors logged on any of our ProCurve switches. DNS is fine on the domain and AD from what I can tell is running happily. There are no DFS or NFS shares setup either. All the shares are standard Windows. I've unchecked the allow the computer to turn off this device to save power box under Power Management on the NIC. "Set Link Speed and Duplex to Auto-negotiate 1000 " Increased Receive Descriptors buffer from 256 to 352 (reserves more CPU resource for handling data) I've run network traces using network monitor and have found the following: 417 8.078125 {SMB:192, NbtSS:25, TCP:24, IPv4:23} 192.168.2.244 192.168.5.35 SMB SMB:R; Nt Create Andx - NT Status: System - Error, Code = (52) STATUS_OBJECT_NAME_NOT_FOUND I've tried different cabling; NICs and switch ports all with the same result. Transferring files from other servers on the domain is fine. All I haven't done is run CHKDSK on the drives to look for any file system errors. On the Vista clients I have also run netsh interface tcp set global autotuning=disabled with no result. Could it be that the server has a faulty drive or that the I/O is too much for it to handle? Any ideas why would the hang cause issues with the other servers on the LAN? Many Thanks.

  Read the article

• Bypassing "Found New Hardware Wizard" / Setting Windows to Install Drivers Automatically

  - by Synetech inc.

  Hi, My motherboard finally died after the better part of a decade, so I bought a used system. I put my old hard-drive and sound-card in the new system, and connected my old keyboard and mouse (the rest of the components—CPU, RAM, mobo, video card—are from the new system). I knew beforehand that it would be a challenge to get Windows to boot and install drivers for the new hardware (particularly since the foundational components are new), but I am completely unable to even attempt to get through the work of installing drivers for things like the video card because the keyboard and mouse won't work (they do work, in the BIOS screen, in DOS mode, in Windows 7, in XP's boot menu, etc., just not in Windows XP itself). Whenever I try to boot XP (in normal or safe mode), I get a bunch of balloons popping up for all the new hardware detected, and a New Hardware Found Wizard for Processor (obviously it has to install drivers for the lowest-level components on up). Unfortunately I cannot click Next since the keyboard and mouse won't work yet because the motherboard drivers (for the PS/2 or USB ports) are not yet installed. I even tried a serial mouse, but to no avail—again, it does work in DOS, 7, etc., but not XP because it doesn't have the serial port driver installed. I tried mounting the SOFTWARE and SYSTEM hives under Windows 7 in order to manually set the "unsigned drivers warning" to ignore (using both of the driver-signing policy settings that I found references to). That didn't work; I still get the wizard. They are not even fancy, proprietary, third-party, or unsigned drivers. They are drivers that come with Windows—as the drivers for CPU, RAM, IDE controller, etc. tend to be. And the keyboard and mouse drivers are the generic ones at that (but like I said, those are irrelevant since the drivers for the ports that they are connected to are not yet installed). Obviously at some point in time over the past several years, a setting got changed to make Windows always prompt me when it detects new hardware. (It was also configured to show the Shutdown Event Tracker on abnormal shutdowns, so I had to turn that off so that I could even see the desktop.) Oh, and I tried deleting all of the PNF files so that they get regenerated, but that too did not help. Does anyone know how I can reset Windows to at least try to automatically install drivers for new hardware before prompting me if it fails? Conversely, does anyone know how exactly one turns off automatic driver installation (and prompt with the wizard)? Thanks a lot.

  Read the article

• Windows Service Limit Crashes Services on Startup

  - by Paul Williams

  We have developed a custom Windows service in C# as part of a large Enterprise application. Our QA department tests multiple versions of this service. The QA lab has several (over 20) copies of this service installed on one Windows 2003 test box. Each copy is in its own folder and has a unique service name, though each executable file is named the same (OurWindowsService.exe, for example). Each service uses the same Windows credentials (a domain user). The purpose of this service is to handle MSMQ messages. The queued messages do all sorts of important stuff. For some reason, they can run only 5 of these services at a time. When we start a 6th, the service crashes on startup. For example, I can start #1, #2, #3, #4, and #5. When I start #6, it crashes. However, if I stop #1 and start #6, #6 runs fine, and now #1 fails to start. When the services crash, the following error appears in the Windows event log: Faulting application OurWindowsService.exe, version 5.40.1.1, faulting module kernel32.dll, version 5.2.3790.4480, fault address 0x0000bef7. I was able to use WinDbg to generate a postmortem dump file. The dump file revealed that the crash occurs trying to delay load SHLWAPI.dll: 0:000> kb100 ChildEBP RetAddr Args to Child 0012ece4 79037966 c06d007e 00000000 00000001 KERNEL32!RaiseException+0x53 0012ed4c 790099ba 00000008 0012ed08 7c82860c mscoree!__delayLoadHelper2+0x139 0012ed98 790075b1 001550c8 0012edac 0012fb34 mscoree!_tailMerge_**SHLWAPI_dll**+0xd 0012edb0 79007623 001550c8 0012edf8 0012edf4 mscoree!XMLGetVersionWithSupported+0x22 0012ee00 790069a4 aa06f1b0 00000000 000001fe mscoree!RuntimeRequest::GetRuntimeVersion+0x56 0012f478 790077aa 00000001 7903fb4c 0012fb34 mscoree!RuntimeRequest::ComputeVersionString+0x5bd 0012f89c 79007802 00000001 0012f8b4 7903fb4c mscoree!RuntimeRequest::FindVersionedRuntime+0x11c 0012f8b8 79007b19 00000001 00000000 aa06fa6c mscoree!RuntimeRequest::RequestRuntimeDll+0x2c 0012ffa4 79007c02 00000001 0012ffbc 00000000 mscoree!GetInstallation+0x72 0012ffc0 77e6f23b 00000000 00000000 7ffdf000 mscoree!_CorExeMain+0x12 0012fff0 00000000 79007bf0 00000000 78746341 KERNEL32!BaseProcessStart+0x23 I believe the error code handed to Kernel32.RaiseException, c06d007e, means Module Not Found, but I'm not certain. Does this sound familiar to anyone? Are we hitting some limit on the number of service instances on some file name? Does MSMQ dislike more than 5 listening services?

  Read the article

• resolve access violation exception (0xC0000005) crashing IIS app pool

  - by Joseph

  IIS 7.5, server 2008 r2, classic asp and asp .net 2.0, 3.5 website same server, same app pool. The past 4 weeks thousands of these errors 'C0000005' are occurring. I know from IIS debug diag tool that 'C0000005' is an access violation error. Below is the top line from my debug diag report. In w3wp__PID__6656__Date__01_08_2011__Time_01_42_46AM__281__First Chance Access Violation.dmp the assembly instruction at asp!CActiveScriptEngine::GetApplication+27 in \\?\C:\Windows\System32\inetsrv\asp.dll from Microsoft Corporation has caused an access violation exception (0xC0000005) when trying to read from memory location 0x00000000 on thread 29 Thread 29 - System ID 6736 Entry point 0x00000000 Create time 1/8/2011 12:46:26 AM Time spent in user mode 0 Days 00:00:00.140 Time spent in kernel mode 0 Days 00:00:00.078 Function Source asp!CActiveScriptEngine::GetApplication+27 vbscript!COleScript::GetDebugApplicationCoreNoRef+2b vbscript!COleScript::FDebuggerEnabled+30 vbscript!COleScript::SetScriptSite+cd asp!CActiveScriptEngine::Init+125 asp!CScriptManager::GetEngine+252 asp!AllocAndLoadEngines+28f asp!ExecuteGlobal+17a asp!Execute+b5 asp!CHitObj::ViperAsyncCallback+3fc asp!CViperAsyncRequest::OnCall+6a comsvcs!CSTAActivityWork::STAActivityWorkHelper+32 ole32!EnterForCallback+f4 ole32!SwitchForCallback+1a8 ole32!PerformCallback+a3 ole32!CObjectContext::InternalContextCallback+15b ole32!CObjectContext::DoCallback+1c comsvcs!CSTAActivityWork::DoWork+12f comsvcs!CSTAThread::DoWork+18 comsvcs!CSTAThread::ProcessQueueWork+37 comsvcs!CSTAThread::WorkerLoop+135 msvcrt!_endthreadex+44 msvcrt!_endthreadex+ce kernel32!BaseThreadInitThunk+e ntdll!__RtlUserThreadStart+70 ntdll!_RtlUserThreadStart+1b BELOW is the faulting module. ASP report Executing ASP requests 0 Request(s) ASP templates cached 0 Template(s) ASP template cache size 0.00 Bytes Loaded ASP applications 1 Application(s) ASP.DLL Version 7.5.7600.16620 ASP application report ASP application metabase key Physical Path Virtual Root Session Count 0 Session(s) Request Count 0 Request(s) Session Timeout 0 minutes(s) Path to Global.asa Server side script debugging enabled False Client side script debugging enabled False Out of process COM servers allowed False Session state turned on False Write buffering turned on False Application restart enabled False Parent paths enabled False ASP Script error messages will be sent to browser False ASP!CACTIVESCRIPTENGINE::GETAPPLICATION+27In w3wp__PID__6656__Date__01_08_2011__Time_01_42_46AM__281__First Chance Access Violation.dmp the assembly instruction at asp!CActiveScriptEngine::GetApplication+27 in \\?\C:\Windows\System32\inetsrv\asp.dll from Microsoft Corporation has caused an access violation exception (0xC0000005) when trying to read from memory location 0x00000000 on thread 29 recent events: server was being brute forced by hackers all of Dec and probably earlier, they weren't able to gain access but did get a virus on and blasted out spam. insatlled AVG and about the 17 or 22 latest patches. after that the app pool started crashing and the server has crashed a couple times since then. I am in no mans land as I am a developer and not a sys admin but I have to assume many roles. So I'm reaching out for help. Sometimes I will see hundreds of these 'C0000005' scriptengine errors in the event log in a matter of seconds and other times just a few times an hour. I googled this line 'ASP!CACTIVESCRIPTENGINE::GETAPPLICATION' and got nothing. Its like the function don't exist or something. I have spent many hours google-ing to no avail and am now turning to the experts on the forums. Thank you for your help

  Read the article

< Previous Page | 591 592 593 594 595 596 597 598 599 600 601 602  | Next Page >