Search Results

Search found 16560 results on 663 pages for 'high tech resources'.

Page 596/663 | < Previous Page | 592 593 594 595 596 597 598 599 600 601 602 603  | Next Page >

• Video memory buswidth vs video memory Bandwidth

  - by Mixxiphoid

  My current video card (9600GT) is dying and I'm searching for a new video card. Between acquiring my current one and now, I got a lot more knowledge about hardware and I want to use that to pick my new card. So I decided to not just buy some popular card blindly, but to search for a card able to handle my hardware requirements. I searched the specs at the NVidia site for the GT640 and was confused by the memory section and some questions raised. My current card's memory bus width is 256bit and has 1GB of memory. I checked Google about the importance of bus width. And all the links basically said the same 'The higher the number the more potential simultaneously traffic can be transferred'. This was already clear to me, yet there are currently a lot of new cards which are considered better than my current one with a lower bus width. To go in more detail about my question I copied the memory info from the NVidia site: GT 640 GT640 GDDR5 Memory Specs: Memory Clock 1.8 Gbps 5.0 Gbps Standard Memory Config 2048 MB 1024 MB Memory Interface DDR3 GDDR5 Memory Interface Width 128-bit 64-bit Memory Bandwidth (GB/sec) 28.5 40.0 What puzzled me is that the Memory Bandwidth seems to me the most important part, yet the lower bus width has the higher 'performance'. Is this due to the fact the memory interface is GDDR5 and is therefore able to have a higher memory clock speed (5Gbps)? If I am to buy a new video card, should I check the bus width? Memory clock? Bandwith? Amount of memory? My current card ahs 1GB memory, so I was searching for a 2GB memory card, but now I'm not so sure any more whether that is really 'better'. My main question: To me it seems that memory performance is made up by the combination of bus width and frequency. Is this true? If yes, why are there so many sites telling me I need to get a card with a high bus width? If no, then what IS important when it goes about memory performance on a video card. NOTE: The memory bandwidth is (almost) never displayed on vendor sites. How can I determine which card is better without knowing the bandwith?

  Read the article

• How can I verify that my SSD is performing as it should?

  - by Jon Skeet

  EDIT: Okay, so I've no idea what caused the change, but after trying loads of different things to work out what was wrong, I've rerun the WEI (about the 4th time in total) and the score has jumped to a far more respectable 7.3. I'm going to leave well alone now :) I've got a brand new 256GB SSD (Crucial CT256M225) which should have stellar performance. However, on my (also brand new) Dell Studio 1557 with Windows 7 Professional 64 bit, it's only giving a performance index of 5.9. I realise the performance index should be taken with a bit of a pinch of salt, but I wonder whether something's wrong. Given this paragraph from this MSDN article on Windows 7, I'd expect to see a high 6.X or possible a 7.X figure: In Windows 7, there are new random read, random write and flush assessments. Better SSDs can score above 6.5 all the way to 7.9. To be included in that range, an SSD has to have outstanding random read rates and be resilient to flush and random write workloads. In the Beta timeframe of Windows 7, there was a capping of scores at 1.9, 2.9 or the like if a disk (SSD or HDD) didn’t perform adequately when confronted with our random write and flush assessments. Feedback on this was pretty consistent, with most feeling the level of capping to be excessive. As a result, we now simply restrict SSDs with performance issues from joining the newly added 6.0+ and 7.0+ ranges. SSDs that are not solid performers across all assessments effectively get scored in a manner similar to what they would have been in Windows Vista, gaining no Win7 boost for great random read performance. How can I diagnose any performance issues with either the disk or how Windows 7 is handling it? Are there any particularly good tools you'd recommend? One note of curiosity: I couldn't install the firmware update (to 1916) until I changed my BIOS handling of the drive to ATA mode; after installing the firmware I tried to boot the Windows installation DVD - but that only worked after turning it back to AHCI mode (which I've left it in). Installing Windows 7 took longer than I expected - it sat at the "Windows is loading files" prompt for a very long time. Likewise it was on "Expanding files (0%)" for a long time. Since installation it's been fine though - but I don't know whether it's really providing quite as beefy performance as it should. EDIT: My netbook with the 64GB equivalent drive has a performance index of 6.6...

  Read the article

• Rails 3 shows 404 error instead of index.html (nginx + unicorn)

  - by Miko

  I have an index.html in public/ that should be loading by default but instead I get a 404 error when I try to access http://example.com/ The page you were looking for doesn't exist. You may have mistyped the address or the page may have moved. This has something to do with nginx and unicorn which I am using to power Rails 3 When take unicorn out of the nginx configuration file, the problem goes away and index.html loads just fine. Here is my nginx configuration file: upstream unicorn { server unix:/tmp/.sock fail_timeout=0; } server { server_name example.com; root /www/example.com/current/public; index index.html; keepalive_timeout 5; location / { try_files $uri @unicorn; } location @unicorn { proxy_pass http://unicorn; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $host; proxy_redirect off; } } My config/routes.rb is pretty much empty: Advertise::Application.routes.draw do |map| resources :users end The index.html file is located in public/index.html and it loads fine if I request it directly: http://example.com/index.html To reiterate, when I remove all references to unicorn from the nginx conf, index.html loads without any problems, I have a hard time understanding why this occurs because nginx should be trying to load that file on its own by default. -- Here is the error stack from production.log: Started GET "/" for 68.107.80.21 at 2010-08-08 12:06:29 -0700 Processing by HomeController#index as HTML Completed in 1ms ActionView::MissingTemplate (Missing template home/index with {:handlers=>[:erb, :rjs, :builder, :rhtml, :rxml, :haml], :formats=>[:html], :locale=>[:en, :en]} in view paths "/www/example.com/releases/20100808170224/app/views", "/www/example.com/releases/20100808170224/vendor/plugins/paperclip/app/views", "/www/example.com/releases/20100808170224/vendor/plugins/haml/app/views"): /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/paths.rb:14:in `find' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/lookup_context.rb:79:in `find' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/base.rb:186:in `find_template' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/render/rendering.rb:45:in `_determine_template' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/render/rendering.rb:23:in `render' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/haml-3.0.15/lib/haml/helpers/action_view_mods.rb:13:in `render_with_haml' etc... -- nginx error log for this virtualhost comes up empty: 2010/08/08 12:40:22 [info] 3118#0: *1 client 68.107.80.21 closed keepalive connection My guess is unicorn is intercepting the request to index.html before nginx gets to process it.

  Read the article

• Passenger 2.2.4, nginx 0.7.61 and SSL

  - by boompa

  Has anyone had any luck configuring Passenger and nginx with SSL? I've spent hours trying to get this configuration working as I'd like, using what few resources there are out there on the net, and I can't get any of the supposedly forwarded headers to show up in the Rails controller. For example, with a conf file of the following (and multiple variations thereof): server { listen 3000; server_name .example.com; root /Users/website/public; passenger_enabled on; rails_env development; } server { listen 3443; root /Users/website/public; rails_env development; passenger_enabled on; ssl on; #ssl_verify_client on; ssl_certificate /Users/website/ssl/server.crt; ssl_certificate_key /Users/website/ssl/server.key; #ssl_client_certificate /Users/website/ssl/CA.crt; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!ADH:RC4+RSA:+HIGH:+MEDIUM:-LOW:-SSLv2:-EXP; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X_FORWARDED_PROTO https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_set_header X-SSL-Subject $ssl_client_s_dn; #proxy_set_header X-SSL-Issuer $ssl_client_i_dn; proxy_redirect off; proxy_max_temp_file_size 0; } and Rails code in the controller like this: request.headers.each { |k, v| RAILS_DEFAULT_LOGGER.error "Header #{k} Val #{v}" } other headers appear, but not those set in nginx, e.g.: Header rack.multithread Val false Header REQUEST_URI Val /login/new Header REMOTE_PORT Val 64021 Header rack.multiprocess Val true Header PASSENGER_USE_GLOBAL_QUEUE Val false Header PASSENGER_APP_TYPE Val rails Header SCGI Val 1 Header SERVER_PORT Val 3443 Header HTTP_ACCEPT_CHARSET Val ISO-8859-1,utf-8;q=0.7,*;q=0.7 Header rack.request.query_hash Val Header DOCUMENT_ROOT Val /Users/website/public I've even gone so far as to modify Passenger's abstract_request_handler's main_loop method, i.e., headers, input = parse_request(client) if headers if headers[REQUEST_METHOD] == PING process_ping(headers, input, client) else headers.each { |h,v| log.unknown "abstract_request_handler: #{h} = #{v}" } process_request(headers, input, client) end end only to find that the supposedly added headers do not exist there either: abstract_request_handler: HTTP_KEEP_ALIVE = 300 abstract_request_handler: HTTP_USER_AGENT = Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; en-US; rv:1.9.1) Gecko/20090624 Firefox/3.5 abstract_request_handler: PASSENGER_SPAWN_METHOD = smart-lv2 abstract_request_handler: CONTENT_LENGTH = 0 abstract_request_handler: HTTP_IF_NONE_MATCH = "b6e8b9afbc1110ee3bf0c87e119252ad" abstract_request_handler: HTTP_ACCEPT_LANGUAGE = en-us,en;q=0.5 abstract_request_handler: SERVER_PROTOCOL = HTTP/1.1 abstract_request_handler: HTTPS = on abstract_request_handler: REMOTE_ADDR = 127.0.0.1 abstract_request_handler: SERVER_SOFTWARE = nginx/0.7.61 abstract_request_handler: SERVER_ADDR = 127.0.0.1 abstract_request_handler: SCRIPT_NAME = abstract_request_handler: PASSENGER_ENVIRONMENT = development abstract_request_handler: REMOTE_PORT = 64021 abstract_request_handler: REQUEST_URI = /login/new abstract_request_handler: HTTP_ACCEPT_CHARSET = ISO-8859-1,utf-8;q=0.7,*;q=0.7 abstract_request_handler: SERVER_PORT = 3443 abstract_request_handler: SCGI = 1 abstract_request_handler: PASSENGER_APP_TYPE = rails abstract_request_handler: PASSENGER_USE_GLOBAL_QUEUE = false I'm tired of banging my head against the wall, so I'd truly appreciate any help I can get!

  Read the article

• Remote host: can tracert, can telnet, can*not* browse: what gives?

  - by MacThePenguin

  One of my customers of the company I work for has made a change to their Internet connection, and now we can't connect to them any more from our LAN. To help me troubleshoot this issue, the network guy on the customer's site has configured their firewall so that a HTTPS connection to their public IP address is open to any IP. I should put https://<customer's IP> in my browser and get a web page. Well, it works from any network I've tried (even from my smartphone), just not from my company's LAN. I thought it may be an issue with our firewall (though I checked its rules and it allows outbound TCP port 443 to anywhere), so I just connected a PC directly to the network connection of our provider, bypassing out firewall completely, and still it didn't work (everything else worked). So I asked for help to our Internet provider's customer service, and they asked me to do a tracert to our customer's IP. The tracert is successful, as the final hop shown in the output is the host I want to reach. So they said there's no problem. :( I also tried telnet <customer's IP> 443 and that works as well: I get a blank page with the cursor blinking (I've tried using another random port and that gives me an error message, as it should). Still, from any browser of any PC in my LAN I can't open that URL. I tried checking the network traffic with Wireshark: I see the packages going through and answers coming back, thought the packets I see passing are far less than they are if I successfully connect to another HTTPS website. See the attached screenshot: I had to blur the IPs, anyway the longer string is my PC's local IP address, the shorter one is the customer's public IP. I don't know what else to try. This is the only IP doing this... Any idea what could I try to find a solution to this issue? Thanks, let me know if you need further details. Edit: when I say "it doesn't work" I mean: the page doesn't open, the browser keeps loading for a long time and eventually shows an error saying that the page cannot be opened. I'm not in my office now so I can't paste the exact message, but it's the usual message you get when the browser reaches its timeout. When I say "it works", I mean the browser loads and shows a webpage (it's the logon page for the customers' firewall admin interface: so there's the firewall brand's logo and there are fields to enter a user id and a password). Update 13/09/2012: tried again to connect to the customer's network through our Internet connection without a firewall. This is what I did: Run a Kubuntu 12.04 live distro on a spare laptop; Updated all the packages I could and installed WireShark; Attached it to my LAN and verified that I couldn't open https://<customer's IP>. Verified that the Wireshark trace for this attempt was the same as the one I've already posted; Verified that I could connect to another customer's host using rdesktop (it worked); Tried to rdesktop to <customer's IP>, here's the output: kubuntu@kubuntu:/etc$ rdesktop <customer's IP> Autoselected keyboard map en-us ERROR: recv: Connection reset by peer Disconnected the laptop from the LAN; Disconnected the firewall from the Extranet connection, connected the laptop instead. Set its network configuration so that I could access the Internet; Verified that I could connect to other websites in http and https and in RDP to other customers' hosts - it all worked as expected; Verified that I could still traceroute to <customer's IP>: I could; Verified that I still couldn't open https://<customer's IP> (same exact result as before); Checked the WireShark trace for this attempt and noticed a different behaviour: I could see packets going out to the customer's IP, but no replies at all; Tried to run rdesktop again, with a slightly different result: kubuntu@kubuntu:/etc/network$ rdesktop <customer's IP> Autoselected keyboard map en-us ERROR: <customer's IP>: unable to connect Finally gave up, put everything back as it was before, turned off the laptop and lost the WireShark traces I had saved. :( I still remember them very well though. :) Can you get anything out of it? Thank you very much. Update 12/09/2012 n.2: I followed the suggestion by MadHatter in the comments. From inside the firewall, this is what I get: user@ubuntu-mantis:~$ openssl s_client -connect <customer's IP>:443 CONNECTED(00000003) If I now type GET / the output pauses for several seconds and then I get: write:errno=104 I'm going to try the same, but bypassing the firewall, as soon as I can. Thanks. Update 12/09/2012 n.3: So, I think ISA Server is altering the results of my tests... I tried installing Wireshark directly on the firewall and monitoring the packets on the Extranet network card. When the destination is the customer's IP, whatever service I try to connect to (HTTPS, RDP or SAProuter), I can only see outbound packets and no response packets whatsoever from their side. It looks like ISA Server is "faking" the remote server's replies, that's why I get a connection using telnet or the openSSL client. This is the wireshark trace from inside our LAN: But this is the trace on the Extranet network card: This makes a bit more sense... I'll send this info to the customer's tech and see if he can make anything out of it. Thanks to all that took the time to read my question and post suggestions. I'll update this post again.

  Read the article

• Vagrant-aws not provisioning

  - by SuperCabbage

  I'm trying to spin up and provision an EC2 instance with Vagrant, it successfully creates the instance up and I can then use vagrant ssh to SSH into the it but Puppet doesn't seem to carry out any provisioning. Upon running vagrant up --provider=aws --provision I get the following output Bringing machine 'default' up with 'aws' provider... WARNING: Nokogiri was built against LibXML version 2.8.0, but has dynamically loaded 2.9.1 [default] Warning! The AWS provider doesn't support any of the Vagrant high-level network configurations (`config.vm.network`). They will be silently ignored. [default] Launching an instance with the following settings... [default] -- Type: m1.small [default] -- AMI: ami-a73264ce [default] -- Region: us-east-1 [default] -- Keypair: banderton [default] -- Block Device Mapping: [] [default] -- Terminate On Shutdown: false [default] Waiting for SSH to become available... [default] Machine is booted and ready for use! [default] Rsyncing folder: /Users/benanderton/development/projects/my-project/aws/ => /vagrant [default] Rsyncing folder: /Users/benanderton/development/projects/my-project/aws/manifests/ => /tmp/vagrant-puppet/manifests [default] Rsyncing folder: /Users/benanderton/development/projects/my-project/aws/modules/ => /tmp/vagrant-puppet/modules-0 [default] Running provisioner: puppet... An error occurred while executing multiple actions in parallel. Any errors that occurred are shown below. An error occurred while executing the action on the 'default' machine. Please handle this error then try again: No error message I can then SSH into the instance by using vagrant ssh but none of my provisioning has taken place, so I'm assuming that errors have occured but I'm not being given any useful information relating to them. My Vagrantfile is as following; Vagrant.configure("2") do |config| config.vm.box = "ubuntu_aws" config.vm.box_url = "https://github.com/mitchellh/vagrant-aws/raw/master/dummy.box" config.vm.provider :aws do |aws, override| aws.access_key_id = "REDACTED" aws.secret_access_key = "REDACTED" aws.keypair_name = "banderton" override.ssh.private_key_path = "~/.ssh/banderton.pem" override.ssh.username = "ubuntu" aws.ami = "ami-a73264ce" end config.vm.provision :puppet do |puppet| puppet.manifests_path = "manifests" puppet.module_path = "modules" puppet.options = ['--verbose'] end end My Puppet manifest is as following; package { [ 'build-essential', 'vim', 'curl', 'git-core', 'nano', 'freetds-bin' ]: ensure => 'installed', } None of the packages are installed.

  Read the article

• Postfix: How to apply header_checks only for specific Domains?

  - by Lukas

  Basically what I want to do is rewriting the From: Header, using header_checks, but only if the mail goes to a certain domain. The problem with header_check is, that I can't check for a combination of To: and From: Headers. Now I was wondering if it was possible to use the header_checks in combination with smtpd_restriction_classes or something similar. I've found a lot information about header_checks and multiple header fields, when searching the net. All of them basically telling me, that one can't combine two header for checking. But I didn't find any information if it was possible to only do a header check if a condition (eg. mail goes to example.com) was met. Edit: While doing some more Research I've found the following article which suggests to add a Service in postfix master.cf, use a transportmap to pass mails for the Domain to that service and have a separate header_check defined with -o. The thing is that I can't get it to work... What I did so far is adding the Service to the master.cf: example unix - - n - - smtpd -o header_checks=regexp:/etc/postfix/check_headers_example Adding the followin Line to the transportmap: example.com example: Last but not least I have two regexp-files for header checks, one for the newly added service, and one to redirect answers to the rewritten domain. check_headers_example: /From:(.*)@mydomain.ain>(.*)/ REPLACE From:[email protected]>$2 Obviously if someone answers, the mail would go to nirvana, so I have the following check_headers defined in the main postfix process: /To:(.*)<(.*)@mydomain.example.com>(.*)/ REDIRECT [email protected]$2 Somehow the Transport is ignored. Any help is appreciated. Edit 2: I'm still stuck... I did try the following: smtpd_restriction_classes = header_rewrite header_rewrite = regexp:/etc/postfix/rewrite_headers_domain smtpd_recipient_restrictions = (some checks) check_recipient_access hash:/etc/postfix/rewrite_table, (more checks) In the rewrite_table the following entries exist: /From:(.*)@mydomain.ain>(.*)/ REPLACE From:[email protected]>$2 All it gets me is a NOQUEUE: reject: 451 4.3.5 Server configuration error. I couldn't find any resources on how you would do that but some people saying it wasn't possible. Edit 3: The reason I asked this question was, that we have a customer (lets say customer.com) who uses some aliases that will forward mail to a domain, let's say example.com. The mailserver at example.com does not accept any mail from an external server that come from a sender @example.com. So all mails that are written from example.com to [email protected] will be rejected in the end. An exception on example.com's mailserver is not possible. We didn't really solve this problem, but will try to work around it by using lists (mailman) instead of aliases. This is not really nice though, nor a real solution. I'd appreciate all suggestions how this could be done in a proper way.

  Read the article

• Looking for Fiddler2 help. connection to gateway refused? Just got rid of a virus

  - by John Mackey

  I use Fiddler2 for facebook game items, and it's been a great success. I accessed a website to download some dat files I needed. I think it was eshare, ziddu or megaupload, one of those. Anyway, even before the rar file had downloaded, I got this weird green shield in the bottom right hand corner of my computer. It said a Trojan was trying to access my computer, or something to that extent. It prompted me to click the shield to begin anti-virus scanning. It turns out this rogue program is called Antivirus System Pro and is pretty hard to get rid of. After discovering the rogue program, I tried using Fiddler and got the following error: [Fiddler] Connection to Gateway failed.Exception Text: No connection could be made because the target machine actively refused it 127.0.0.1:5555 I ended up purchasing SpyDoctor + Antivirus, which I'm told is designed specifically for getting rid of these types of programs. Anyway, I did a quick-scan last night with spydoctor and malware bytes. Malware picked up 2 files, and Spydoctor found 4. Most were insignificant, but it did find a worm called Worm.Alcra.F, which was labeled high-priority. I don’t know if that’s the Anti-Virus Pro or not, but SpyDoctor said it got rid of all of those successfully. I tried to run Fiddler again before leaving home, but was still getting the "gateway failed" error. Im using the newest version of firefox. When I initially set up the Fiddler 2.2.8.6, I couldn’t get it to run at first, so I found this faq on the internet that said I needed to go through ToolsOptionsSettings and set up an HTTP Proxy to 127.0.0.1 and my Port to 8888. Once I set that up and downloaded this fiddler helper as a firefox add-on, it worked fine. When I turn on fiddler, it automatically takes my proxy setting from no proxy (default) to the 127.0.0.1 with Port 8888 set up. It worked fine until my computer detected this virus. Anyway, hopefully I've given you sufficient information to offer me your best advice here. Like I said, Spydoctor says the bad stuff is gone, so maybe the rogue program made some type of change in my fiddler that I could just reset or uncheck or something like that? Or will I need to completely remove fiddler and those dat files and rar files I downloaded? Any help would be greatly appreciated. Thanks for your time.

  Read the article

• Scoping a home dev server

  - by AbhikRK

  Hi. I’m looking to build a multi-purpose home development server. In this post, I’m looking to outline what I want from such a system, and the ‘why’s of it, to some limited extent, and finally, some rudiments of how I’m looking to go about that. I’m mostly a developer, with just about some sysadmin familiarity. So, please excuse, correct me, and suggest on any ignorance which would come across in the following ;-) It will serve the following goals to start with:- NAS (Looking at using ZFS) Source control repo e.g Git server Database e.g MySQL server Continuous Integration e.g Hudson server Other stuff as and when they come up e.g RabbitMQ etc A development sandbox to play around with new stuff I want to achieve a high uptime for 2-5 as much as possible. They should run as independent services and with minimal maintenance. (e.g TurnKey Linux appliances) I’m thinking of running them as individual Xen DomUs. Then, maybe the NAS can be a Dom0 and 6 can be another DomU. The User for this would be mostly me. I can see 2-4 being sometimes used by 2-3 users, but that would be infrequent. I’m looking for a repeatable setup. Ideally I’d like to automate this setup through Chef or Puppet or something similar. Once everything runs, I want to be able to ssh/screen/tmux into 1-6 from my laptop or any other computer on the LAN/on-the-go. My queries are:- Is putting 1-6, all of them on a single box, a good idea? If so, what kind of hardware should I be looking at, for a low-cost, low-power setup? Although not at present, but in future I might be looking at adding audio/media servers to the mix. Would that impact the answers to 1? I have an old Pentium 3 and 810e motherboard combination. Is there any way I could put it to use? I had a look at the Sheevaplug, and was wondering if I could split off the NAS on its own using that. But ruled it out preliminarily due to its reported heating issues. Is it something i should still consider? Thanks in advance

  Read the article

• Scoping a home dev server

  - by AbhikRK

  Hi. I’m looking to build a multi-purpose home development server. In this post, I’m looking to outline what I want from such a system, and the ‘why’s of it, to some limited extent, and finally, some rudiments of how I’m looking to go about that. I’m mostly a developer, with just about some sysadmin familiarity. So, please excuse, correct me, and suggest on any ignorance which would come across in the following ;-) It will serve the following goals to start with:- NAS (Looking at using ZFS) Source control repo e.g Git server Database e.g MySQL server Continuous Integration e.g Hudson server Other stuff as and when they come up e.g RabbitMQ etc A development sandbox to play around with new stuff I want to achieve a high uptime for 2-5 as much as possible. They should run as independent services and with minimal maintenance. (e.g TurnKey Linux appliances) I’m thinking of running them as individual Xen DomUs. Then, maybe the NAS can be a Dom0 and 6 can be another DomU. The User for this would be mostly me. I can see 2-4 being sometimes used by 2-3 users, but that would be infrequent. I’m looking for a repeatable setup. Ideally I’d like to automate this setup through Chef or Puppet or something similar. Once everything runs, I want to be able to ssh/screen/tmux into 1-6 from my laptop or any other computer on the LAN/on-the-go. My queries are:- Is putting 1-6, all of them on a single box, a good idea? If so, what kind of hardware should I be looking at, for a low-cost, low-power setup? Although not at present, but in future I might be looking at adding audio/media servers to the mix. Would that impact the answers to 1? I have an old Pentium 3 and 810e motherboard combination. Is there any way I could put it to use? I had a look at the Sheevaplug, and was wondering if I could split off the NAS on its own using that. But ruled it out preliminarily due to its reported heating issues. Is it something i should still consider? Thanks in advance Have posted this question previously on SuperUser but no responses yet. So was wondering if this is a more apt forum for this.

  Read the article

• Varnish 503 Guru Mediation errors with pfsense and healthy apache

  - by Fammy

  We are running a pfsense firewall / load balancer with varnish as service, In front of Fedora linux webservers running apache. We are getting intermittent 503 guru mediation errors. We are a bit stuck scratching our heads because it is not easily repeatable. The timeouts are set to 30s (connect and first byte) but yet the 503 page will show instantly, not after 30s. Then if you refresh immediately it may very well work instantly and sometimes for a 100 refreshes. The load average on the web servers is < 1, the DB server is < 3 (all servers (web, db, pfsense/varnish) are physical rather than VM. I would have thought if the timeouts were being hit then the 503 page would only appear after 30s am I mistaken? Also when an error happens there does not appear to be any corresponding error in apache's log files. This seems to affect pages as well as images, so it is possible to have the page load fine, and for 9/10 images on the page to be fine but 1 not work An example of the varnish debug is below. It says no backend connection but I can't figure out why, if the load was high on apache I could understand it being flaky The machines are on the same gig ethernet lan 21 ReqStart c *IP-REMOVED* 33418 1274368062 21 RxRequest c GET 21 RxURL c /fashion/ 21 RxProtocol c HTTP/1.1 21 RxHeader c User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.0.5) Gecko/2008121622 Fedora/3.0.5-1.fc10 Firefox/3.0.5 21 RxHeader c Host: *ourdomain.com* 21 RxHeader c Accept: */* 21 RxHeader c Accept-Encoding: deflate, gzip 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error restart 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error restart 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error deliver 21 VCL_call c deliver deliver 21 TxProtocol c HTTP/1.1 21 TxStatus c 503 21 TxResponse c Service Unavailable 21 TxHeader c Server: Varnish 21 TxHeader c Content-Type: text/html; charset=utf-8 21 TxHeader c Content-Length: 384 21 TxHeader c Accept-Ranges: bytes 21 TxHeader c Date: Wed, 11 Apr 2012 10:36:17 GMT 21 TxHeader c X-Varnish: 1274368062 21 TxHeader c Age: 0 21 TxHeader c Via: 1.1 varnish 21 TxHeader c Connection: close 21 TxHeader c X-Cache: MISS 21 Length c 384 21 ReqEnd c 1274368062 1334140577.449995041 1334140577.450334787 1.794108152 0.000282764 0.000056982

  Read the article

• usb_modeswitch not switching

  - by deniz

  After I upgraded from kernel 2.6.18 to 3.5.3 modeswitch started not to work for me. Although lsusb shows my usb modem, usb_modeswitch does not switch it. My system information is like below. I ran lsusb, dmesg, usb-devices and usb_modeswitch their output is like below. usb_modeswitch instead of switching my modem it says "No devices in default mode found. Nothing to do. Bye.". Can you offer a solution? Kernel: Linux 3.5.3 usb_modeswitch: 1.2.3-1 usb_modeswitch-data: 20120120-1 usbutils: 006-1 libusb: 1.0.8-0.1 root@localhost$ lsusb Bus 002 Device 029: ID 12d1:1446 Huawei Technologies Co., Ltd. root@localhost$ dmesg [70112.477080] usb 2-1.4: new high-speed USB device number 30 using ehci_hcd [70112.567757] scsi49 : usb-storage 2-1.4:1.0 [70112.567842] scsi50 : usb-storage 2-1.4:1.1 [70113.571433] scsi 49:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 [70113.572304] scsi 50:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2 [70113.574169] sr0: scsi-1 drive [70113.574223] sr 49:0:0:0: Attached scsi CD-ROM sr0 [70113.574250] sr 49:0:0:0: Attached scsi generic sg1 type 5 [70113.574350] sd 50:0:0:0: Attached scsi generic sg2 type 0 [70113.577173] sd 50:0:0:0: [sdb] Attached SCSI removable disk root@localhost$ usb-devices T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 30 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1446 Rev=00.00 S: Manufacturer=Huawei Technologies S: Product=HUAWEI Mobile C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage root@localhost$ cat /etc/usb_modeswitch.d/12d1\:1446 # Huawei, newer modems TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" MessageContent="55534243123456780000000000000011062000000100000000000000000000" root@localhost$ usb_modeswitch -c /etc/usb_modeswitch.d/12d1:1446 -v 12d1 -p 1446 -W * usb_modeswitch: handle USB devices with multiple modes * Version 1.2.3 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above) ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1446 TargetVendor= 0x12d1 TargetProduct= not set TargetClass= not set TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243123456780000000000000011062000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set InquireDevice enabled (default) Success check disabled System integration mode disabled usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Skipping non bus directory devices usb_os_find_busses: Skipping non bus directory drivers usb_os_find_busses: Skipping non bus directory uevent usb_os_find_busses: Skipping non bus directory drivers_probe usb_os_find_busses: Skipping non bus directory drivers_autoprobe Looking for target devices ... No devices in target mode or class found Looking for default devices ... No devices in default mode found. Nothing to do. Bye. Thanks in advance.

  Read the article

• Ubuntu: Multiple NICs, one used only for Wake-On-LAN

  - by jcwx86

  This is similar to some other questions, but I have a specific need which is not covered in the other questions. I have an Ubuntu server (11.10) with two NICs. One is built into the motherboard and the other is a PCI express card. I want to have my server connected to the internet via my NAT router and also have it able to wake from suspend using a Magic Packet (henceforth referred to as Wake-On-LAN, WOL). I can't do this with just one of the NICs because each has an issue - the built-in NIC will crash the system if it is placed under heavy load (typically downloading data), whilst the PCI express NIC will crash the system if it is used for WOL. I have spent some time investigating these individual problems, to no avail. My plan is thus: use the built-in NIC solely for WOL, and use the PCI express card for all other network communication except WOL. Since I send the WOL Magic Packet to a specific MAC address, there is no danger of hitting the wrong NIC, but there is a danger of using the built-in NIC for general network access, overloading it and crashing the system. Both NICs are wired to the same LAN with address space 192.168.0.0/24. The built-in ethernet card is set to have interface name eth1 and the PCI express card is eth0 in Ubuntu's udev persistent rules (so they stay the same upon reboot). I have been trying to set this up with the /etc/network/interfaces file. Here is where I am currently: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 auto eth1 iface eth1 inet static address 192.168.0.254 netmask 255.255.255.0 I think by not specifying a gateway for eth1, I prevent it being used for outgoing requests. I don't mind if it can be reached on 192.168.0.254 on the LAN, i.e. via SSH -- it's IP is irrelevant to WOL, which is based on MAC addresses -- I just don't want it to be used to access internet resources. My kernel routing table (from route -n) is Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 My question is this: Is this sufficient for what I want to achieve? My research has thrown up the idea of using static routing to specify that eth1 should only be used for WOL on the local network, but I'm not sure this is necessary. I have been monitoring the activity of the interfaces using iptraf and it seems like eth0 takes the vast majority of the packets, though I am not sure that this will be consistent based on my configuration. Given that if I mess up the configuration, my system will likely crash, it is important to me to have this set up correctly!

  Read the article

• Win7 x64 unresponsive for a minute or so. HD failing?

  - by Gaia

  On a fully updated Win7 x64, every so often the system stalls for a minute or so. This has been going on for a couple months now. By stalling I mean the mouse responds and I can move windows around, but any window, any program, that is open becomes whiteish when I select it AND any new programs will not open. It doesn't matter what kind of program it is. When the stall stops all clicks I made (open new programs for example) take effect. Nothing shows up consistently (as in every time this happens) in the event log. Today though I was able to find something, but it doesn't reveal much other than the "system was unresponsive". It's a 7009 for "A timeout was reached (30000 milliseconds) while waiting for the Windows Error Reporting Service service to connect." It doesn't matter if I have any USB devices plug-in or not. I've ran Microsoft Security Essentials and Malwarebytes. While the machine is unresponsive, I've noticed that Drive D (the other partition on the single internal HD in this laptop) is displayed like this in explorer. This never occurs with Drive C or any other drive on the machine. . SMART report for the physical drive: Read benchmark by HD Tune 5 Pro, probably the most telling piece of the puzzle. Isn't this alone enough to see there is a problem with the drive, regardless of whether the unresponsiveness is caused by such purported problem? Here is a short hardware report: Computer: LENOVO ThinkPad T520 CPU: Intel Core i5-2520M (Sandy Bridge-MB SV, J1) 2500 MHz (25.00x100.0) @ 797 MHz (8.00x99.7) Motherboard: LENOVO 423946U Chipset: Intel QM67 (Cougar Point) [B3] Memory: 8192 MBytes @ 664 MHz, 9.0-9-9-24 - 4096 MB PC10600 DDR3 SDRAM - Samsung M471B5273CH0-CH9 - 4096 MB PC10600 DDR3 SDRAM - Patriot Memory (PDP Systems) PSD34G13332S Graphics: Intel Sandy Bridge-MB GT2+ - Integrated Graphics Controller [D2/J1/Q0] [Lenovo] Intel HD Graphics 3000 (Sandy Bridge GT2+), 3937912 KB Drive: ST320LT007, 312.6 GB, Serial ATA 3Gb/s Sound: Intel Cougar Point PCH - High Definition Audio Controller [B2] Network: Intel 82579LM (Lewisville) Gigabit Ethernet Controller Network: Intel Centrino Advanced-N 6205 AGN 2x2 HMC OS: Microsoft Windows 7 Professional (x64) Build 7601 The drive less than 1 year old. Do I have a defective drive? Seagate Tools diag says there is nothing wrong with the drive... UPDATE: I noticed that the windows error reporting service entered the running state then the stopped state and the space between the two events was exactly 2 minutes. Which error it was trying to report I don't know. I check the "Reliability Monitor" and it shows no errors to be reported. I've disabled the windows error reporting service to see if the problem stops.

  Read the article

• phpMyAdmin causes php-fpm worker to restart (502 Bad Gateway)

  - by rndbit

  I am trying to set up a test site for myself. Everything works fine except phpMyAdmin. php installation loads my test site scripts, they work fine, however trying to load phpMyAdmin i get 502 Bad Gateway error. Judging from logs (that are not too helpful) it seems that php-fpm worker is crashing each time phpmyadmin is being accessed. No clue how or why.. Does anyone have any idea? nginx log: *3 recv() failed (104: Connection reset by peer) while reading response header from upstream, And php-fpm log: [07-Jun-2012 14:19:51] WARNING: [pool www] child 32179 exited on signal 11 (SIGSEGV) after 3.217902 seconds from start [07-Jun-2012 14:19:51] NOTICE: [pool www] child 32351 started My nginx conf: user nginx; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; keepalive_timeout 65; fastcgi_buffers 8 16k; fastcgi_buffer_size 32k; include /etc/nginx/conf.d/*.conf; server { listen 443 ssl; listen 80; server_name testsite.net www.testsite.net; ssl on; ssl_certificate /var/www/html/admin/ssl/certificate.pem; ssl_certificate_key /var/www/html/admin/ssl/privatekey.pem; ssl_session_timeout 1m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_ciphers HIGH:!aNULL:!MD5:!kEDH; ssl_prefer_server_ciphers on; access_log off; location ~ \.php$ { root /var/www/html; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include /etc/nginx/fastcgi_params; } location / { root /var/www/html; index index.php; } } } php.ini is standard, with cgi.fix_pathinfo=0 php-fpm.conf: include=/etc/php-fpm.d/*.conf [global] pid = /var/run/php-fpm/php-fpm.pid error_log = /var/log/php-fpm/error.log log_level = notice php-fpm.d/www.conf: [www] listen = 127.0.0.1:9000 listen.allowed_clients = 127.0.0.1 user = nginx group = nginx pm = dynamic pm.max_children = 10 pm.start_servers = 1 pm.min_spare_servers = 1 pm.max_spare_servers = 10 slowlog = /var/log/php-fpm/www-slow.log php_flag[display_errors] = on php_admin_value[error_log] = /var/log/php-fpm/www-error.log php_admin_flag[log_errors] = on

  Read the article

• Ubuntu Server 12.04 CPU Load

  - by zertux

  I have a Server (2x Hexa-Core Xeon E5649 2.53GHz w/HT with 32GB RAM and 20000 GB Bandwidth) running Ubuntu Server 12.04 LTS. The server runs LAMP and serves one website only, the estimated number of users is to be ~ 15,000 at the same time. At the moment i have around 2000 users online each of them runs 50 MySQL queries (small values mostly select and insert) from the beginning until the end of the session. Server CPU Load is high at this number of connections while the RAM usage is almost 1GB out of 32GB its worth mentioning that the server was running very fast with no problems at all but am concerned about the load average. http://s12.postimage.org/z7hi6mz3h/photo.png top - 03:02:43 up 9 min, 2 users, load average: 50.83, 30.14, 12.83 Tasks: 432 total, 1 running, 430 sleeping, 0 stopped, 1 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 66.5%id, 33.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 32939992k total, 3111604k used, 29828388k free, 84108k buffers Swap: 2048280k total, 0k used, 2048280k free, 1621640k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2860 root 20 0 25820 2288 1420 S 3 0.0 0:11.18 htop 1182 root 20 0 0 0 0 D 2 0.0 0:01.46 kjournald 1935 mysql 20 0 12.3g 161m 7924 S 1 0.5 102:31.45 mysqld 11 root 20 0 0 0 0 S 0 0.0 0:00.38 kworker/0:1 1822 www-data 20 0 247m 25m 4188 D 0 0.1 0:01.81 apache2 2920 www-data 20 0 0 0 0 Z 0 0.0 0:01.20 apache2 <defunct> 2942 www-data 20 0 247m 23m 3056 D 0 0.1 0:00.20 apache2 3516 www-data 20 0 247m 23m 3028 D 0 0.1 0:00.06 apache2 3521 www-data 20 0 247m 23m 3020 D 0 0.1 0:00.09 apache2 3664 www-data 20 0 247m 23m 3132 D 0 0.1 0:00.09 apache2 3674 www-data 20 0 247m 23m 3252 D 0 0.1 0:00.06 apache2 3713 www-data 20 0 247m 23m 3040 D 0 0.1 0:00.09 apache2 1 root 20 0 24328 2284 1344 S 0 0.0 0:03.09 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0 0.0 0:00.01 ksoftirqd/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 8 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 9 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/1:0 root@server:~/codes# vmstat 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 19 0 0 29684012 86112 1689844 0 0 19 590 254 231 48 0 47 5 23 0 0 29704812 86128 1697672 0 0 4 320 11100 8121 77 1 22 0 33 0 0 29671044 86156 1705308 0 0 0 5440 13190 9140 95 1 4 0 33 3 0 29670088 86160 1706288 0 0 0 32932 12275 7297 99 0 1 0 35 0 0 29693456 86188 1710724 0 0 4 676 12701 7867 98 1 1 0 ^C I have not changed any of the default configurations that comes with Ubuntu. Is this load normal for such powerful server ? is there any optimization i can make to Apache/MySQL to minimize the load ? What do you recommend ?

  Read the article

• Network use of Gaming PC

  - by Matthew Patrick Cashatt

  Background After YEARS of waiting, I built the custom gaming PC of my dreams: Intel i7 - 975 Extreme Edition 3.3ghz (overclocked to 4.0) ATI Radeon 5970 2gb Corsair 256 gb SSD Drive 2 TB Sata II 3.0 7200rpm data drive 12 GB Kingston Hyper-X (1600mhz) DDR3 Windows 7 Ultra 64 bit And so on. . . Problem I hooked this beast up to our home theater and settled in for a great gaming season only to realize a couple of drawbacks: It's hard to accurately wax bad guys using a keyboard in your lap whilst reclined on your couch (and using a wireless keyboard). It's hard to read the text on the screen (i.e. menus, etc). I find that a 1:1 ratio (screen diagonal inch to inch away from screen) is optimum, but using the home theater, it's more like 1:3 which has me squinting unless I sit on the coffee table. The wife always seems to want the TV the same time I do and, unfortunately "Real Housewives of Beverly Hills" and Battlefield BC don't mix. I am losing the battle in the home theater room, but the PC has to stay there (long story). So, this leaves me with the option of playing in my home office which is about 30 feet away from the home theater. I am a software developer so I have a pretty decent set up in my office--multiple 1080p monitors, HP Envy 17 which can run games like Crysis in 720p with out stammering too much. Also, I can game very comfortably at my desk in the office. Still, even though the set up in my office can run games well enough, I don't want to regress to that when I have worked YEARS for an awesome gaming PC that can run everything on ultra high settings. My Question What are my options for running my games on the beastly desktop in the Home Theater, but physically playing in my office about 30 feet away? A really long HDMI cable? LAN/RDC? Details that May Help We have an open crawlspace so running cable from HT room to office is no problem. I already have networked the house with a LAN Any help is GREATLY appreciated. Thanks, Matt

  Read the article

• what is Remote Desktop Services in Windows Server 2008 R2 all about?

  - by fejesjoco

  Seriously, I'm lost in all that sales mumbo-jumbo. Let's say I want 1 or 2 users to be able to remotely log on to a server, run Word, Visual Studio, Firefox, and whatever. Do I gain anything at all if I install Remote Desktop Services? Or do I just install Desktop Experience feature pack, enable remote desktop and voila, nobody will ever notice the difference? Here's what TechNet says about Remote Desktop Session Host: A Remote Desktop Session Host (RD Session Host) server is the server that hosts Windows-based programs or the full Windows desktop for Remote Desktop Services clients. Users can connect to an RD Session Host server to run programs, to save files, and to use network resources on that server. Users can access an RD Session Host server by using Remote Desktop Connection or by using RemoteApp. The good old simple remote desktop can also host a full Windows desktop for remote clients so that they can run programs, save files and do all that stuff. Why do they write about it like it's such a great new invention, besides that they want to sell it? RDSH doesn't seem all that different at all. What do I install when I install RDSH, since all those features are already there in Windows? What's even more confusing is that you need to take special care when you want to install applications to an RDSH so that they will be usable by many concurrent users. Why? All the modern applications install the program files in one directory, store some common settings in the ProgramData folder and the HKLM hive, and store user specific settings in the Users folder and the HKCU hive. They are designed to be usable by many users on the same machine. 2 or 2000 users can use them concurrently without any efforts. I can sign in with 2 users to a server with only remote desktop enabled, and both of us can run Word or anything without any problems, can't we? So what changes if I set RDSH to install mode, or what happens if I don't? Why is the feature to switch between install and execute mode there at all? Yes I know of some advantages in Remote Desktop Services, like there's no 2 user limit, it supports virtualization, video acceleration and stuff, it has a whole infrastructure with gateway, web access, connection broker, etc. But I don't need those, so if you take these away, how are these two technologies different? From the articles it seems like they are completely different technologies, whereas it looks to me that they are completely the same at the core, and Remote Desktop Services just adds some additional features, but doesn't reinvent anything.

  Read the article

• Looking for Fiddler2 help. connection to gateway refused...just got rid of a virus?

  - by john mackey

  I use Fiddler2 for facebook game items, and it's been a great success. I accessed a website to download some dat files I needed. I think it was eshare, ziddu or megaupload, one of those. Anyway, even before the rar file had downloaded, I got this weird green shield in the bottom right hand corner of my computer. It said a Trojan was trying to access my computer, or something to that extent. It prompted me to click the shield to begin anti-virus scanning. It turns out this rogue program is called Antivirus System Pro and is pretty hard to get rid of. After discovering the rogue program, I tried using Fiddler and got the following error: [Fiddler] Connection to Gateway failed. Exception Text: No connection could be made because the target machine actively refused it 127.0.0.1:5555 I ended up purchasing SpyDoctor + Antivirus, which I'm told is designed specifically for getting rid of these types of programs. Anyway, I did a quick-scan last night with spydoctor and malware bytes. Malware picked up 2 files, and Spydoctor found 4. Most were insignificant, but it did find a worm called Worm.Alcra.F, which was labeled high-priority. I don’t know if that’s the Anti-Virus Pro or not, but SpyDoctor said it got rid of all of those successfully. I tried to run Fiddler again before leaving home, but was still getting the "gateway failed" error. Im using the newest version of firefox. When I initially set up the Fiddler 2.2.8.6, I couldn’t get it to run at first, so I found this faq on the internet that said I needed to go through ToolsOptionsSettings and set up an HTTP Proxy to 127.0.0.1 and my Port to 8888. Once I set that up and downloaded this fiddler helper as a firefox add-on, it worked fine. When I turn on fiddler, it automatically takes my proxy setting from no proxy (default) to the 127.0.0.1 with Port 8888 set up. It worked fine until my computer detected this virus. Anyway, hopefully I've given you sufficient information to offer me your best advice here. Like I said, Spydoctor says the bad stuff is gone, so maybe the rogue program made some type of change in my fiddler that I could just reset or uncheck or something like that? Or will I need to completely remove fiddler and those dat files and rar files I downloaded? Any help would be greatly appreciated. Thanks for your time.

  Read the article

• Why does unpartitioned Hitachi HDS5C3020 drive start consuming 50% more power 15 minutes after boot?

  - by Pro Backup

  In a Debian 6.0.6 system there are 74 pieces of 2TB Toshiba DT01ABA200 drives. These drives are identified as Hitachi HDS5C3020BLE630 drives running firmware revision MZ4OAAB0. 64 Drives attached via HP SAS expander cards to an LSI 2008 SAS controller, another 5 drives are connected directly to the mainboard, 4 drives are connected to a Sil based PCI controller and last 1 drive is only powered and has no data cable connected. The controller LSI and Sil card's their onboard BIOS are both disabled and the mpt2sas and sata_sil modules are removed from the Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux kernel. The mpt2sas module is loaded after boot using a modprobe command in /etc/rc.local. These 74 drives are not partitioned, neither formatted and also not mounted. The system consumes: with 0 drives: 70.6 - 70.9 Watt (also 15 minutes after boot); with 74 drives: 330 - 360 Watt, just after boot (is equivalent to 3.5 - 3.9W per drive in idle state); with 74 drives: 420 - 466 Watt, each time in the 15th minute of uptime (is equivalent to 4.7 - 5.3W per drive in idle state). The drive specification lists 4.7W as read/write, and 3.3W as idle power consumption. The increased power consumption is most likely on the 5V line, because after roughly 1 minute an "over current protection" (OCP) of the power supply (PSU) shuts down the power. The used PSU is a single rail model with an OCP of 122A on the 12V line and 55A on the 5V line. Regression: It doesn't matter whether the drive its APM value is set to disabled or 1 (maximum power saving). The operating system records no read/write activity in /proc/diskstats. The values there are identical (28 read, 0 write operations) as immediately after the modprobe operation. Can't test what happens when booting into the mainboard it's BIOS - to exclude any OS intervention - because the Super Micro X8SI6-F mainboard running firmware 06/27/12 has a bug that incorrectly reads a +74.0 C CPU sensor temperature as "High" in BIOS mode, and shuts down the power after 1 minute. What might be causing the drive read/write activity on all drives in the 15th minute after boot and how to prevent it from happening?

  Read the article

• MBPro, mid 2010 can't see Dlink DIR655 signal after sleep etc

  - by user88114

  This is my son's MBP 7,1 running Snow Leopard 10.6.7. Router signal is fine since iPad, Wintel on same table 20 feet from router are fine. the MBP however frequently wakes and fails to find the internet. iStumbler can see 1 neighbours hub and my garden hub are there but can't get to the normal DIR655 wifi... no ping no en0 or en1 device seems to exist. Airport off and on does not help. He just resets router and it all works but this does not please me! I must admit the winter sometimes seems to loose connect too, but less so. The DIR655 (hardware rev A3) is on the original EU firmware 1.10, I'm cautious about jumping to latest 1.31EU since no downgrade seems to be possible and that feels a bit risky as so much is set up and working fine. If I use the DIR655 admin web and release the lease the MBP has then wake it all worked OK. So I suspect lease timing/locking issue but unsure how to check up, plus why iStumbler seems to say the network is not visible at all when I sit on the iPad right next to it just fine.. I do not think there are any channel overlaps and we also have RFquiet DECT phones (Orchid) that are silent until lifted or called. Anyway signals all show low interference and high throughput except for this failure to connect. Just walked the MBP to the garden office and iStumbler now sees the more distant DIR655 signal although it will not connect to it (does not show under Sys Prefs NetNetwork names) even after airport off & on... It also refuses to connect to my garden network (an old Belkin acting as AP wired to DIR655), the signal it can see and even net name in Sys Prefs NetNetwork names (2 mins later):NOW both names ARE visible, but both fail to accept the correct WPA2 password and keep asking again after failing to connect. IT ALL MAKES NO SENSE TO ME. Just revoked the lease for the MBP on DIR655 and no changes although this seemed to help MBP wake into connection 1 hour ago. OK a bit of walking about to report. Carried MBP across garden towards DIR655, a few other wifis show up on iStumbler, low signals all channel 1. Right next to DIR655 but iStumbler not showing it, although most other wifi's have gone. I'd say iStubler is suffering timeouts&hangs but hard to be sure. Lots of attempts to Airport on/off, join other etc and suddenly I get to connect, get given new IP (I revoked), can browse. Walk away, connection drops quite soon at 30 feet then reconnected briefly then died again. MUST ATTEND ELSEWHERE FOR A BIT...

  Read the article

• Linux per-process resource limits - a deep Red Hat Mystery

  - by BobBanana

  I have my own multithreaded C program which scales in speed smoothly with the number of CPU cores.. I can run it with 1, 2, 3, etc threads and get linear speedup.. up to about 5.5x speed on a 6-core CPU on a Ubuntu Linux box. I had an opportunity to run the program on a very high end Sunfire x4450 with 4 quad-core Xeon processors, running Red Hat Enterprise Linux. I was eagerly anticipating seeing how fast the 16 cores could run my program with 16 threads.. But it runs at the same speed as just TWO threads! Much hair-pulling and debugging later, I see that my program really is creating all the threads, they really are running simultaneously, but the threads themselves are slower than they should be. 2 threads runs about 1.7x faster than 1, but 3, 4, 8, 10, 16 threads all run at just net 1.9x! I can see all the threads are running (not stalled or sleeping), they're just slow. To check that the HARDWARE wasn't at fault, I ran SIXTEEN copies of my program independently, simultaneously. They all ran at full speed. There really are 16 cores and they really do run at full speed and there really is enough RAM (in fact this machine has 64GB, and I only use 1GB per process). So, my question is if there's some OPERATING SYSTEM explanation, perhaps some per-process resource limit which automatically scales back thread scheduling to keep one process from hogging the machine. Clues are: My program does not access the disk or network. It's CPU limited. Its speed scales linearly on a single CPU box in Ubuntu Linux with a hexacore i7 for 1-6 threads. 6 threads is effectively 6x speedup. My program never runs faster than 2x speedup on this 16 core Sunfire Xeon box, for any number of threads from 2-16. Running 16 copies of my program single threaded runs perfectly, all 16 running at once at full speed. top shows 1600% of CPUs allocated. /proc/cpuinfo shows all 16 cores running at full 2.9GHz speed (not low frequency idle speed of 1.6GHz) There's 48GB of RAM free, it is not swapping. What's happening? Is there some process CPU limit policy? How could I measure it if so? What else could explain this behavior? Thanks for your ideas to solve this, the Great Xeon Slowdown Mystery of 2010!

  Read the article

• How to install missing Sound Drivers in Ubuntu?

  - by Sakamoto Kazuma

  I seem to be missing drivers for my Gateway laptop MA7. I have looked in System-Admin-Hardware Drivers, but it does not show up in there.There are also no devices listed in Sound-Hardware. I'm guessing at this point that I don't have the driver installed. However, I get the following output: admin@machine001:~$ cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xd8240000 irq 22 admin@machine001:~$ And my lspci shows: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) 04:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 04:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 04:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) I have also checked alsamixer, and nothing is muted. No headphones plugged into headphone jack either. So the question now is, how do I get sound to work on my laptop? It doesn't work for any application.

  Read the article

• IIS httpTracing setting has no effect

  - by digahill

  I'm trying to troubleshoot some performance issues we are having on a specific ASP.NET page with Microsoft's Perfecto Tool on IIS 7.5. Perfecto uses the ETW hooks build in to IIS to report on specific HTTP request, and is working quite well. However, I only want IIS to emit traces for one specific page, say "Default.aspx" in my TestApp Web Application. Following the instructions on the httpTracing man page, I should be able to add the traceUrls element to my root web.config file for TestApp. This doesn't seem to affect tracing whatsoever when I do so. For example, I've used the following settings in the web.config file and every request that hits the IIS server is sending tracing messages that are in turn picked up by Perfecto. (In the System.WebServer section) <httpTracing> <traceUrls> <add value="/Default.aspx" /> </traceUrls> </httpTracing> I then found that the applicationHost.config file on the server had an empty element. I tried removing this element, as well as the httpTracing element in the web.config. After a machine reboot, I was still getting tracing messages! My understanding is that the presense of the httpTracing element is what controlls whether ETW tracing is on or not. I ensured there was no reference to httpTracing in the machine.config, too. At a loss, I decided to remove the IIS Tracing feature with Server Manager. After a reboot, I no longer got ETW tracing. I then reinstalled IIS Tracing feature with Server Manager. As expected, the httpTracing element reappeared in the applicationhost.config file. Tracing messages began sending again for all sites and pages. I then tried to use the traceUrls element at the applicationhost.config level. This also didn't filter out and traces. I must be misunderstanting something key with how httpTracing works. There aren't many resources on the web to help me, either. Can anyone tell me if what I'm trying should work? Has anyone else had success filtering tracing message per page with traceUrls? I should note that I also tried changing with the following setting in applicationhost.config to "allow". It didn't seem to help. <section name="httpTracing" overrideModeDefault="Allow" />

  Read the article

• networked storage for a research group, 10-100 TB

  - by Marc

  this is related to this post: http://serverfault.com/questions/80854/scalable-24-tb-nas-for-research-department but perhaps a little more general. Background: We're a research lab of around 10 people who do a lot of experiments that involve taking pictures at one of several lab setups and then analyzing it an one of several lab computers. Each experiment may produce 2 or 3 GB of data, and we are generating data at the rate of about 10 TB/year. Right now, we are storing the data on a 6-bay netgear readynas pro, but even with 2 TB drive, this only gives us 10 TB of storage. Also, right now we are not backing up at all. Our short term backup plan is to get a second readynas, put it in a different building and mirror the one drive onto the other. Obviously, this is somewhat non-ideal. Our options: 1) We can pay our university $400/ TB /year for "backed up" online storage. We trust them more than we trust us, but not a whole lot. 2) We can continue to buy small NASs and mirror them between offices. One limit, although stupid, is that we don't have an unlimited number of ethernet jacks. 3) We can try to implement our own data storage solution, which is why I'm asking you guys. One thing to consider is that we're a very transient population and none of us are network administration experts. I will probably be here only another year or so, and graduate students, who are here the longest, have a 5-6 year time scale. So nothing can require expert oversight. Our data transfer rates are low - most of the data will just sit on the server waiting for someone to look at it once or twice - so we don't need a really high speed system. Given these contraints, can someone recommend a fairly low-cost, scalable, more or less turn key shared data storage system with backup in a separate physical location. Does such a thing exist or should we just pay the university to take care of it for us? As a second question, our professor just got tenure and is putting together a budget. Here the goal is to ask for as much as you can and hope you get a fraction of it. So the same question, minus the low-cost. Without budget constraints, can you recommend a scalable turn-key backed up storage system. Thanks

  Read the article

< Previous Page | 592 593 594 595 596 597 598 599 600 601 602 603  | Next Page >