Search Results

Search found 28957 results on 1159 pages for 'single instance'.

Page 598/1159 | < Previous Page | 594 595 596 597 598 599 600 601 602 603 604 605  | Next Page >

• Ubuntu 11.10 loads from live usb fine, but boots to black screen from harddrive. Why?

  - by Estel

  A few days ago I had a hard drive failure, which was running Windows XP (32-bit) just fine. The second hard drive in my computer held a few unimportant files, so I formatted it in the Ubuntu setup and installed 11.10 without a hitch. I had been using it for about a week, but decided to install Windows 7 (64-bit) in order to utilize Networking with my home server (running Windows Server 2000). My system is 64-bit based, and thus I had no problems installing other than a basic RAM error that required me to remove my RAM down to a single stick. I played with the settings in Windows 7 for around an hour before I shut down. After reinstalling the RAM, Windows 7 would not boot. In this, I then assumed that something about my system was rejecting Win7 and I reinstalled Ubuntu. However, now Ubuntu (11.10) boots into black screen, and I've already attempted activating the grub menu with the shift key, and following steps listed here: https://wiki.ubuntu.com/X/Troubleshooting/BlankScreen but nothing seems to work. I've reinstalled twice now, with the same result each time. Now, the very odd part about this whole scenario is that the USB I installed from has no problems booting as a live USB. This puzzles me greatly, because the hard drive boots straight to black screen and the live USB loads normally. At this point, my only theory is that the boot sector of the hard disk was somehow corrupted with Win7, and that Ubuntu was unable to completely write through. I used Darik's Boot n Nuke to wipe the drive, but was met with an error, this also puzzles me because the hard disk has no promblems reading or writing. Any suggestions/comments are appreciated. If you have a theory, I will be more than happy to oblige. Additional information: Intel Core2 Duo e6400 2.13GHz nVidia GeForce 7-series (7900 GS) 4 GB DDR2 333MHz (2x 2GB) Dell XPS 410 BIOS Revision 2.5.3

  Read the article

• Server 2008 Active directory file sharing Restriction

  - by Usman

  My network scenario is: Two location connected each other through Wireless towers. 1st network ip address are 10.10.10.1 to 10.10.10.150 2nd network ip address are 10.10.10.200 to 10.10.10.254 Both location using their own ACTIVE DIRECTORY (MS SERVER 2008) and share their data with each other network through file sharing. My Problem is that every single client can explore the whole network. by simply typing \computername. i want to implement some restriction on network regarding file sharing. i want to restrict 1st Network Clients to open 2nd network Computer or server. Is there have any Group Policy or Folder permission scenario that i implement on my both network..

  Read the article

• Can't change folder background

  - by newcomer

  I tried to change via dragging from the Backgrounds and Emblems window, but the icon just goes back to that window rather than changing the folder background.However, I can change the task bar by this drag-n-drop. Probably it is something about changing ownership permission? if so how to change that? In /home/mashruf/.gconf/apps/nautilus/preferences/%gconf.xml file it says:, Should I change this file? how? <?xml version="1.0"?> <gconf> <entry name="click_policy" mtime="1297597800" type="string"> <stringvalue>single</stringvalue> </entry> <entry name="default_folder_viewer" mtime="1297597336" type="string"> <stringvalue>list_view</stringvalue> </entry> <entry name="media_autorun_x_content_open_folder" mtime="1297534321" type="list" ltype="string"> </entry> <entry name="media_autorun_x_content_ignore" mtime="1297534321" type="list" ltype="string"> </entry> <entry name="media_autorun_x_content_start_app" mtime="1297534321" type="list" ltype="string"> <li type="string"> <stringvalue>x-content/software</stringvalue> </li> </entry> <entry name="start_with_location_bar" mtime="1297300028" type="bool" value="true"/> <entry name="side_pane_view" mtime="1297269334" type="string"> <stringvalue>NautilusTreeSidebar</stringvalue> </entry> <entry name="navigation_window_saved_maximized" mtime="1297600306" type="bool" value="false"/> <entry name="navigation_window_saved_geometry" mtime="1297600306" type="string"> <stringvalue>964x608+59+2</stringvalue> </entry> <entry name="sidebar_width" mtime="1297390418" type="int" value="192"/> </gconf>

  Read the article

• internet speed and routers are controlled by whom

  - by Ozgun Sunal

  i need to learn two things. each is related to other a bit. The first one is, while our LAN speed is usually 100 Mbps or at gigabit levels(very big compared to WAN speeds), WAN speed for instance DSL connections are far less than this. However, we are able to download huge files at those Mb speeds. Isn't this weird? [my real concern is why WAN speed is lower than LAN speeds] Who controls those routers around the large Internet? (while we, as web clients are connected to Internet, packets travel through those routers to the destination network/s).But, are those routers all inside the ISP network and if not, who controls those large numbers of routers?

  Read the article

• How to copy text out of a PDF without losing formatting?

  - by Colen

  When I copy text out of a PDF file and into a text editor, it ends up mangled in a variety of ways. Formatting like bold and italics are lost; soft line breaks within a paragraph of text are converted to hard line breaks; dashes to break a word over two lines are preserved even when they shouldn't be; and single and double quotes are replaced with ? signs. Ideally, I'd like to be able to copy text from a PDF and have formatting converted to HTML codes, "smart quotes" converted to " and ', and line breaks done properly. Is there any way to do this?

  Read the article

• What You Said: How You Set Up a Novice-Proof Computer

  - by Jason Fitzpatrick

  Earlier this week we asked you to share your tips and tricks for setting up a novice-proof computer; read on to see how your fellow readers ensure friends and relatives have a well protected computer. Image available as wallpaper here. If you only listen to a single bit of advice from your fellow readers, let that advice be the importance of separate and non-administrative user accounts. Grant writes: I have two boys, now 8 and 10, who have been using the computer since age 2. I set them up on Linux (Debian first, now Ubuntu) with a limited rights account. They can only make a mess of their own area. Worst case, empty their home directory and let them start over. I have to install software for them, but they can’t break the machine without causing physical damage (hammers, water, etc.) My wife was on Windows, and I was on Debian, and before they had their own, they knew they could only use my computer, and only logged in as themselves. All accounts were password protected, so that was easy to enforce. What Is the Purpose of the “Do Not Cover This Hole” Hole on Hard Drives? How To Log Into The Desktop, Add a Start Menu, and Disable Hot Corners in Windows 8 HTG Explains: Why You Shouldn’t Use a Task Killer On Android

  Read the article

• Using nested public classes to organize constants

  - by FrustratedWithFormsDesigner

  I'm working on an application with many constants. At the last code review it came up that the constants are too scattered and should all be organized into a single "master" constants file. The disagreement is about how to organize them. The majority feel that using the constant name should be good enough, but this will lead to code that looks like this: public static final String CREDITCARD_ACTION_SUBMITDATA = "6767"; public static final String CREDITCARD_UIFIELDID_CARDHOLDER_NAME = "3959854"; public static final String CREDITCARD_UIFIELDID_EXPIRY_MONTH = "3524"; public static final String CREDITCARD_UIFIELDID_ACCOUNT_ID = "3524"; ... public static final String BANKPAYMENT_UIFIELDID_ACCOUNT_ID = "9987"; I find this type of naming convention to be cumbersome. I thought it might be easier to use public nested class, and have something like this: public class IntegrationSystemConstants { public class CreditCard { public static final String UI_EXPIRY_MONTH = "3524"; public static final String UI_ACCOUNT_ID = "3524"; ... } public class BankAccount { public static final String UI_ACCOUNT_ID = "9987"; ... } } This idea wasn't well received because it was "too complicated" (I didn't get much detail as to why this might be too complicated). I think this creates a better division between groups of related constants and the auto-complete makes it easier to find these as well. I've never seen this done though, so I'm wondering if this is an accepted practice or if there's better reasons that it shouldn't be done.

  Read the article

• String manipulation functions in SQL Server 2000 / 2005

  - by Vipin

  SQL Server provides a range of string manipulation functions. I was aware of most of those in back of the mind, but when I needed to use one, I had to dig it out either from SQL server help file or from google. So, I thought I will list some of the functions which performs some common operations in SQL server. Hope it will be helpful to you all. Len (' String_Expression' ) - returns the length of input String_Expression. Example - Select Len('Vipin') Output - 5 Left ( 'String_Expression', int_characters ) - returns int_characters characters from the left of the String_Expression.     Example - Select Left('Vipin',3), Right('Vipin',3) Output -  Vip,  Pin  LTrim ( 'String_Expression' ) - removes spaces from left of the input 'String_Expression'  RTrim ( 'String_Expression' ) - removes spaces from right of the input 'String_Expression' Note - To removes spaces from both ends of the string_expression use Ltrim and RTrim in conjunction Example - Select LTrim(' Vipin '), RTrim(' Vipin ') , LTrim ( RTrim(' Vipin ')) Output - 'Vipin ' , ' Vipin' , 'Vipin' (Single quote marks ' ' are not part of the SQL output, it's just been included to demonstrate the presence of space at the end of string.) Substring ( 'String_Expression' , int_start , int_length ) - this function returns the part of string_expression. Right ( 'String_Expression', int_characters ) - returns int_characters characters from the right of the String_Expression.

  Read the article

• Xterm is not completely erasing field lines

  - by user26367

  We have a SSH tunnel to a remote unix box from Windows clients using Cygwin. It launches a terminal program from the unix box locally on the Windows box for data input. The xterm window is launched as follows xterm -fn 10x20 -bg DodgerBlue4 -fg white -cr white -ls -geometry 90x30 -e program When a screen goes from read only mode to edit mode, the edit fields have ____. When going back to read only mode, a single pixel artifact is left behind for each field. *readonly* User: *edit* User: ___________ *after edit exit* User: . <- this dot is left behind Any idea what we need to change to fix this?

  Read the article

• Is it worth moving from Microsoft tech to Linux, NodeJS & other open source frameworks to save money for a start-up?

  - by dormisher

  I am currently getting involved in a startup, I am the only developer involved at the moment, and the other guys are leaving all the tech decisions up to me at the moment. For my day job I work at a software house that uses Microsoft tech on a day to day basis, we utilise .NET, SqlServer, Windows Server etc. However, I realise that as a startup we need to keep costs down, and after having a brief look at the cost of hosting for Windows I was shocked to see some of the prices for a dedicated server. The cheapest I found was £100 a month. Also if the business needs to scale in the future and we end up needing multiple servers, we could end up shelling out £10's of £000's a year in SQL Server / Windows Server licenses etc. I then had a quick look at the price of Linux hosting for a dedicated server and saw the price was waaaaaay lower than windows hosting. One place was offering a machine with 2 cores for less than £20 a month. This got me thinking maybe the way to go is open source on Linux. As I write a lot of Javascript at work (I'm working on a single page backbone app at the moment), I thought maybe NodeJS and a web framework like Express would be cool to use. I then thought that instead of using SQL why not use an open source NoSQL database like MongoDB, which has great support on NodeJS? My only concern is that some of the work the application is going to do is going to be dynamically building images and various other image related stuff, i.e. stuff that is quite CPU heavy - so I'm thinking of maybe writing anything CPU heavy in C++ and consuming it as a module in Node. That's the background - but basically is Linux a good match for: Hosting a NodeJS/Express site? Compiling C++ node modules? Using a NoSQL DB like MongoDB? And is it a good idea to move to these unfamiliar technologies to save money?

  Read the article

• uWSGI and python virtual env

  - by user27512

  I'm trying to use uWSGI with a virtual env in order to use the Trac bug tracker on it. I've installed system-wide uwsgi via pip. Next, I've installed trac in a virtualenv $ virtualenv venv $ . venv/bin/activate $ pip install trac I've then written a simple uWSGI configuration script: [uwsgi] master = true processes = 1 socket = localhost:3032 home = /srv/http/trac/venv/ no-site = true gid = www-data uid = www-data env = TRAC_ENV=/srv/http/trac/projects/my_project module = trac.web.main:dispatch_request But when I try to launch it, it fails: $ uwsgi --http :8000 --ini /etc/uwsgi/vassals-available/my_project.ini --gid www-data --uid www-data ... Set PythonHome to /srv/http/trac/venv/ ... *** Operational MODE: single process *** ImportError: No module named trac.web.main unable to load app 0 (mountpoint='') (callable not found or import error) I think uWSGI isn't using the virtual env. When inside the virtual env, I can import trac.web.main without having an ImportError. How can I do that ? Thanks

  Read the article

• Installing a fake microphone on Windows Server.

  - by Adrian

  My application, that is running on Windows Server (which is an instance on Amazon EC2) requires Skype to be able to make phone calls. The server, of course, does not have a microphone installed and I don't need it to have one, because my application changes the input source to a wav file when the call is established. However, Skype has a strict rule that a microphone must be installed for a call to be made. Thus I want to install a fake microphone that will trick Skype's configuration. So far, I was able to start and run the Windows Sound service, which enabled all of the sound settings. Any ideas are very welcome!

  Read the article

• How do I put back different SCSI hard drives into their original RAID arrays across different servers?

  - by Edgar

  I have potentially a big mess in my hands: I received today a box with several hard drives that used to be connected to different servers each one of them using an unknown - at least as of right now- RAID configuration. Regretfully, these are not marked and I'm not sure how to go about putting them back into their original servers. Currently I don't have much more information: I don't know what type of array was being used on each instance and I don't have any specifics about the RAID controller originally used on each one of the servers (currently these servers are at a remote location with no easy access). Is there a way to sort through this mess? What would be the consequences of using trial and error to go about it? This might be a very basic question but I don't have much experience dealing with RAID arrays.

  Read the article

• Linux: Limiting data throughput (pipe) in bytes per second?

  - by sdaau

  Hi all, I was wandering if there is a Linux program that can limit data throughput of a pipe - in actual bytes per second?. From what I gather, applicable for the purposes would be bfr, however, it has been removed from Debian (Removal candidate: bfr) cpipe, however, it seems the lowest resolution it will support is kB/s, meaning that buffer writes can still reach MB/s ([SOLVED] Is there a program to limit terminal pipe speed? - Page 2 - Ubuntu Forums) What I'd want is to be able to specify something like cat example.txt | ratelimit -Bps 100 > /dev/ttyUSB0 ... and actually have a single byte from example.txt sent each 1/100 = 0.01 sec (or 10 ms) to 'output'.. Thanks in advance for any suggestions, Cheers!

  Read the article

• PHP Image gallery that integrates well into custom CMS

  - by Thorarin

  I've been trying to find an image gallery that plays nice with our custom CMS. I've evaluated a number of them, but none of them seems to have the feature list that I would like: Run on LAMP environment Free software or low license costs (the website belongs to a non-profit organisation) Multi-user support Multiple albums. We're posting concert pictures, and would like an album per event. Pluggable authentication system. I want to reuse the accounts we have for our CMS. Permissions can be done inside the gallery itself, but I want to have a single sign on solution in a maintainable manner, by writing my own plugin/add-on for the software. Upload support (multiple images at the same time) And preferrably also: Can be integrated into a PHP page layout without IFRAMEs Automatic resizing of uploaded images to a maximum size Ability for visitors to place comments This combination is proving hard to find, especially the authentication requirement. I don't want to mess around all over the place in the source code to make it use the existing authentication. A plugin would be ideal, but alternatively a well thought out software design that allows for maintainable surgical changes would be acceptable. Any suggestions on which software I should take a closer look into?

  Read the article

• getting started as a web developer [closed]

  - by kmote

  I have over 10 years of programming experience building (Windows-based) desktop applications and utilities (VC++, C#, Python). My goal over the next year is to start transitioning to web application development. I want to teach myself the fundamental tools and technologies that would be considered essential for building professional, online, interactive, visually-stunning, data-driven web apps -- the kind described in Google's recently released "Field Guide: Building Great Web Applications". So my question is, what are the primary, most commonly-used technologies that seasoned professionals will need in their tool belt in the coming years? My plan was to start coming up to speed in Javascript, HTML5, & CSS, and then to do a deep dive into ASP.NET and Ajax, along with SQL DBs. (I was surprised to not be able to find a single book at Amazon with a broad, general scope like this, which caused me to start second-guessing this approach.) So, seasoned professionals: am I on the right track? Are there some glaring omissions in my list? Or some unnecessary inclusions? I would welcome any book suggestions along these lines as well.

  Read the article

• Looking for a better Factory pattern (Java)

  - by Sam Goldberg

  After doing a rough sketch of a high level object model, I am doing iterative TDD, and letting the other objects emerge as a refactoring of the code (as it increases in complexity). (That whole approach may be a discussion/argument for another day.) In any case, I am at the point where I am looking to refactor code blocks currently in an if-else blocks into separate objects. This is because there is another another value combination which creates new set of logical sub-branches. To be more specific, this is a trading system feature, where buy orders have different behavior than sell orders. Responses to the orders have a numeric indicator field which describes some event that occurred (e.g. fill, cancel). The combination of this numeric indicator field plus whether it is a buy or sell, require different processing buy the code. Creating a family of objects to separate the code for the unique handling each of the combinations of the 2 fields seems like a good choice at this point. The way I would normally do this, is to create some Factory object which when called with the 2 relevant parameters (indicator, buysell), would return the correct subclass of the object. Some times I do this pattern with a map, which allows to look up a live instance (or constructor to use via reflection), and sometimes I just hard code the cases in the Factory class. So - for some reason this feels like not good design (e.g. one object which knows all the subclasses of an interface or parent object), and a bit clumsy. Is there a better pattern for solving this kind of problem? And if this factory method approach makes sense, can anyone suggest a nicer design?

  Read the article

• Two views of Federation: inside out, and outside in

  - by Darin Pendergraft

  IDM customers that I speak to have spent a lot of time thinking about enterprise SSO - asking your employees to log in to multiple systems, each with distinct hard to guess (translation: hard to remember) passwords that fit the corporate security policy for length and complexity is a strategy that is just begging for a lot of help-desk password reset calls. So forward thinking organizations have implemented SSO for as many systems as possible. With the mix of Enterprise Apps moving to the cloud, it makes sense to continue this SSO strategy by Federating with those cloud apps and services.  Organizations maintain control, since employee access to the externally hosted apps is provided via the enterprise account.  If the employee leaves, their access to the cloud app is terminated when their enterprise account is disabled.  The employees don't have to remember another username and password - so life is good. From the outside in - I am excited about the increasing use of Social Sign-on - or BYOI (Bring your own Identity).  The convenience of single-sign on is extended to customers/users/prospects when organizations enable access to business services using a social ID.  The last thing I want when visiting a website or blog is to create another account.  So using my Google or Twitter ID is a very nice quick way to get access without having to go through a registration process that creates another username/password that I have to try to remember. The convenience of not having to maintain multiple passwords is obvious, whether you are an employee or customer - and the security benefit of not having lots of passwords to lose or forget is there as well. Are enterprises allowing employees to use their personal (social) IDs for enterprise apps?  Not yet, but we are moving in the right direction, and we will get there some day.

  Read the article

• Can there be multiple monitors with these video cards and setup

  - by z_Zelman

  I have a Acer Aspire TimelineX 4830TG-6808 laptop running windows 7 Ultimate with one VGA port and one HDMI port. It has one Intel HD Graphics family card and one NVIDIA GeForce GT 540M. Right now I have one monitor running via the VGA port, and also the basic laptop monitor. When I look at the monitor setup, I see one unused video card available. Can I have another monitor via the HDMI port? If I cannot run three monitors, is there some way I could make a large "single" desktop that extends over two monitors? For the sake of celerity, maybe something like having a virtual machine window that extends over two monitors. Could this maybe come from third party software?

  Read the article

• Issue with Windows Server backup

  - by mamu

  I have windows server 2008 r2 installed, Only service running on it is hyper-v. I am trying to take backup using windows server backup feature and it fails with following error in eventlog The backup operation that started at '?2009?-?08?-?22T18:42:14.123000000Z' has failed because the Volume Shadow Copy Service operation to create a shadow copy of the volumes being backed up failed with following error code '2155348129'. Please review the event details for a solution, and then rerun the backup operation once the issue is resolved. Above error itself is point to other event logs for more detail but i can't find anything in event logs Then i ran following command vssadmin list writers It had following out of ordinary in list Writer name: 'Microsoft Hyper-V VSS Writer' Writer Id: {66841cd4-6ded-4f4b-8f17-fd23f8ddc3de} Writer Instance Id: {d15c5f78-121c-464f-b23b-f285e919b05c} State: [8] Failed Last error: Inconsistent shadow copy How could i resolve this?

  Read the article

• Get the interface and ip address used to connect to a specific host (ip)

  - by umop

  I'm sure this has been asked and answered before, but I wasn't able to find it, so hopefully this will at least link someone to the right place. I want to find out my local interface and ip address used to reach a certain host. For instance, if I had 3 adapters connected to my box and they all three went to different networks, I'd like to know which of the three (specifically, its ip address) is used to reach my.local.intranet (in this case, it would be a vpn tunnel interface). I suspect this is a job for ifconfig or traceroute, but I haven't been able to find the correct switches. I'm running OSX 10.7 (Darwin) Thanks!

  Read the article

• What are the Windows G: through Z: drives used for?

  - by Tom Wijsman

  In Windows you have a C: drive. The first things labeled beyond that seems to be extra stuff. So my DVD drive is D: and if you put in a USB stick it becomes F:. And then some people also have A: and B:. But then, what and where are G: through Z: drives for? Is it possible to connect so many things to a computer to make them all in use? Or more than them? Would it give a BSOD? Or would this slow down the system somehow? Or what would happen? What if I want to connect even more drives to the computer? Because with the hard drive limits it's more efficient to buy more drives than to buy a single drive with a lot of capacity. Is it possible to create drive letters like 0: through Z: or AA: through ZZ:?

  Read the article

• Strategies for avoiding SQL in your Controllers... or how many methods should I have in my Models?

  - by Keith Palmer

  So a situation I run into reasonably often is one where my models start to either: Grow into monsters with tons and tons of methods OR Allow you to pass pieces of SQL to them, so that they are flexible enough to not require a million different methods For example, say we have a "widget" model. We start with some basic methods: get($id) insert($record) update($id, $record) delete($id) getList() // get a list of Widgets That's all fine and dandy, but then we need some reporting: listCreatedBetween($start_date, $end_date) listPurchasedBetween($start_date, $end_date) listOfPending() And then the reporting starts to get complex: listPendingCreatedBetween($start_date, $end_date) listForCustomer($customer_id) listPendingCreatedBetweenForCustomer($customer_id, $start_date, $end_date) You can see where this is growing... eventually we have so many specific query requirements that I either need to implement tons and tons of methods, or some sort of "query" object that I can pass to a single -query(query $query) method... ... or just bite the bullet, and start doing something like this: list = MyModel-query(" start_date X AND end_date < Y AND pending = 1 AND customer_id = Z ") There's a certain appeal to just having one method like that instead of 50 million other more specific methods... but it feels "wrong" sometimes to stuff a pile of what's basically SQL into the controller. Is there a "right" way to handle situations like this? Does it seem acceptable to be stuffing queries like that into a generic -query() method? Are there better strategies?

  Read the article

• Firefox cannot recognize certificates for well knows sites

  - by RCola

  When trying to connect to well known sites, for instance hotmail.com Firefox shows that This Connection in Untrusted. In the OptionsAdvancedCertificates it's configured to select one matching certificate automatically. Why Firefox does not trust current connection? Can it be Man-in-the-middle attack or it's something like broken certificate storage on my computer? UPDATE UPDATE2 Solved: the problem is Antivirus Web Access protection. It interferes with HTTPS connection. Similar to Man-in-the-middle? Why ESET cannot do it correctly?

  Read the article

• Recursively apply ACL permissions on Mac OS X (Server)?

  - by mralexgray

  For years I've used the strong-armed-duo of these two suckers... sudo chmod +a "localadmin allow read,write,append,execute,\ delete,readattr,writeattr,readextattr,writeextattr,\ readsecurity,writesecurity,chown" sudo chmod +a "localadmin allow list,search,add_file,add_subdirectory,\ delete_child,readattr,writeattr,readextattr,\ writeextattr,readsecurity,writesecurity,chown" to, for what I figured was a recursive, and all-encompassing, whole-volume-go-ahead for each and every privilege available (for a user, localadmin). Nice when I, localadmin, want to "do something" without a lot of whining about permissions, etc. The beauty is, this method obviates the necessity to change ownership / group membership, or executable bit on anything. But is it recursive? I am beginning to think, it's not. If so, how do I do THAT? And how can one check something like this? Adding this single-user to the ACL doesn't show up in the Finder, so… Alright, cheers.

  Read the article

< Previous Page | 594 595 596 597 598 599 600 601 602 603 604 605  | Next Page >