Search Results

Search found 2123 results on 85 pages for 'crossover cable'.

Page 6/85 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

  • Pros/cons to turning off cable modem

    - by Jay
    A little off the wall perhaps, but ... I have a cable modem and a router for a wireless home network. Is it a good or a bad idea to turn it off at night and during the day when we're all at work or school? Or should I leave it on 24/7. I was thinking that leaving it on constantly makes me more vulnerable to hackers, not to mention wasting electricity. (Though I'd guess the amount of electricity used by a cable modem and a router is probably pretty trivial. Still, every little bit helps.) When I have turned it off and turned it on again, it takes several minutes for it to go through its little dialog with the cable company and get me connected to the Internet again, which is annoying but not a big deal. Anyone know any good reasons one way or the other?

    Read the article

  • VGA cable casuing resolution issue

    - by LatishS
    Hello, I recently bought a new VGA cable . When connected Windows 7 detects my monitor as a generic plug and play monitor. The resolution goes bad with the screen blurred. This problem disappears when i connect my original VGA cable. Also Windows 7 detects my LG monitor correctly in this case. I am pretty sure it is something to do with the VGA cable but have no idea what could be the possible issue. Any pointers would be very much appreciated.

    Read the article

  • D Link DSL G624T Router will work wirelessly but not via cable

    - by Andy Fensome
    I have a D Link router which works in providing a wireless internet connection for my main PC and secondary notebook. I have been advised that the internet connection to the main pc will be better if I wire the router directly to the PC. I have tried this and can not get a connection. I just keep getting the message network cable unplugged. I have had the ethernet adaptor checked out on the pc and the cable is good ( also checked out). Anything I can do or do I have a bad router. I have tried the cable in all 4 ports and the message is still the same.

    Read the article

  • windows7 cant get to internet( cable connection)

    - by user29297
    I'm using a window 7 with wireless & cable equipments to connect to internet, it's been fine for moths. But Three days ago, the local connection ran out of control and i can no longer use the cable to get access to internet. But fortunately the wireless equipment still works. I reinstalled the driver, took off/inserted in the cable, the computer still didn't work. And every time I let the computer diagnose itself, it told me that :"Default gateway is not valid"(or something else, forgive my terrible english XD). If anyone could give any advice, i will be very appreciated. And I'm in california, but i don't know the gateway of this area.

    Read the article

  • Bizarre and very specific Internet connection loss

    - by Synetech
    Yesterday (Friday, September 21, 2012), my Internet connection started acting up. After some testing, I confirmed a very specific and baffling set of symptoms: Internet connection goes away every 25-35 minutes (I did not confirm the exact interval, but it seems to be about 30 mins.) Only some protocols are affected; HTTP*, P2P, etc. stop working; FTP, etc. continue to work When it’s stopped, cannot even ping router or cable-modem IPs or view their firmware pages Domain-names and IPs are irrelevant (for protocols that stop working, neither work, for those that still work, both work) Resetting router fixes it for another 30 minutes Keeping the connection idle or active doesn’t seem to make a difference (nor the bandwidth usage in that period) Connecting directly to cable-modem allows it to work indefinitely Disconnecting the router from the cable-modem works indefinitely (no Internet connection obviously, but can still access router IP and firmware page) Connecting the router to the cable-modem, but putting the modem on standby also works indefinitely Same problem with both a wireless laptop and wired (on any port) desktop (both Windows 7; will try to test Windows XP when possible) Nothing had changed in the days leading up to the issue. No modifications to the networking configuration or the router; there were not even any Windows updates except for an MSSE definition update. Waiting does not fix it, nor does any amount of fiddling with anything; only resetting the router fixes it for 30 minutes (resetting the cable-modem doesn't work either) I tried cleaning the pins in the router’s plugs, but that didn’t help, which was not really a surprise since I was not getting a lost connection error. Obviously my first thought was that the router was having a problem, and this is borne out by some tests. The problem is that when it drops, it is not a full drop since I can still do things like ftp ftp.mcafee.com and such which means that the connection and DNS are still working. Moreover, if it were the router, then why does it stay alive indefinitely when not connected to the cable-modem (i.e., no outside influence)? The problem doesn't seem to be either the cable-modem nor the router, but rather an interaction between the two, like something from the outside (port scan? hacker? ISP?) that is triggering a problem in the router. I see that there have been a couple of vulnerabilities for the DI-524, but those were a while back and should be fixed since I have the last firmware for it. I don’t think it’s my ISP (Rogers) since I have been using the router for several years without problem and can connect indefinitely when bypassing it. But I can’t rule them out since that is one of the only possible things that could have suddenly changed. Does anybody have any ideas of explanations, fixed, or tests? (I note that when I opened the router, I heard a very high-pitched noise from somewhere near the capacitors/ferrite ring which I don’t think I heard the last time I opened it a few years ago, but then if it were that, then why would it affect only a very small, specific set of functions?)

    Read the article

  • cpu usage and near to crash when i plug in the power cable

    - by mohamad
    i have had this problem since i installed ubuntu 12.4 on my laptop (on all of distro i have this problem execpt of backtrack) my problem is when i start my linux while it connect to power source there is no problem everything works fine . but when i disconnect and wants to work with battery it crash i mean everything work tooooo slowly and my cpu usage goes to 100 ... it happen too when i start my linux with battery and want to connect the power source to it .... it happens again . i updated my distro and now on i have 12.10 on my laptop but it has this problem . my lap top is hp probook 4520s my graphic card is ati radeon 530 v and i installed catalyst control center on my lap top and it works fine but the only problem is that what i said ...is it relate to my graphic card ???

    Read the article

  • WIFI: iPhone/iPad getting much slower bandwidth than laptop

    - by Sam
    I just got cable internet installed (Comcast). It claims that my down speed should be 25mbit. Over wifi, I get close to that on my laptop, but only about 8 on average with my iPhone/iPad. I'm using testmy.net in the browser on all devices. I have an ARRIS / Motorola SurfBoard SB6141 DOCSIS 3.0 Cable Modem and a Medialink Wireless N Broadband Router. I read somewhere that disabling WMM and the firewall on the router would help (is this even a safe idea?). I've tried both, and neither seem to make much of a difference, if any at all (sidebar: I've noticed that my download speeds vary wildly with cable internet... on my laptop, I'll get 12 down, then 22 five minutes later. Is this typical for cable internet?).

    Read the article

  • Laptop HDMI out to monitor DVI in

    - by Roy Rico
    I have a laptop that i'm trying to fix, and it has HDMI out. I have a cable i bought for my HTPC which does DVI out to HDMI in, which worked fine. Was hoping to be able to use this same cable for HDMI out to DVI in, is it possible? UPDATE: Point of clarification, The laptop's display doesn't work (it was dropped) and I'm trying to figure out what's working and what isn't. in addition to HDMI out, it has VGA out, but that seems to have a short in it, and doesn't display properly (sometimes it works, sometimes, it shows stuff in 256 colors in 800x640). I can tell the LCD screen works (comes on) so i think it's whatever is carrying the data to it that doesn't work. I know more often than know, the display is what breaks... The cable i'm using is a standard HDMI to DVI cable, there are no audio connections or anything. Thanks!

    Read the article

  • How do I backup my Ubuntu 9.10 system and then restore it to a new machine with different hardware?

    - by EricJLN
    I have a nicely configured Ubuntu 9.10 machine, with crossover linux (from Codeweavers) installed. I have the Nvidia drivers installed. Everything is just as I want it. Now I want to move to a new machine with different hardware: different sized hard drive, different size RAM, different video card, etc. I tried the technique suggested on Ubuntu forums, "Howto: Backup and restore your system!". The results: New system complains about swap not being found New system complains about not finding Nvidia hardware, and I can't open the System-Administration-Hardware Drivers application (i.e., /usr/bin/jockey-gtk) to fix the problem. As result of nvidia, X-Windows is throwing errors, and the on screen process for fixing X-Windows isn't working. How do I restore a backup of my old system, including my Crossover Linux installation, to a new machine with different hardware installed?

    Read the article

  • Slow wireless about 1/3 bandwidth of wired from cable modem

    - by Rhino
    HP DV6000 Wireless G Broadcom Netgear WNDR3400 router properly configured. Windows laptops using wireless G and N are considerably faster than mine. 12.04 LTS, all restricted drivers and all up to date. 50Mbps wired and 9-21 Mbps wireless on Ubuntu. 00:14.0 Bridge [0680]: NVIDIA Corporation MCP51 Ethernet Controller [10de:0269] (rev a3) Subsystem: Hewlett-Packard Company Presario V6133CL [103c:30b7] Kernel driver in use: forcedeth 03:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11a/b/g [14e4:4312] (rev 02) Subsystem: Hewlett-Packard Company Broadcom 802.11a/b/g WLAN [103c:1370] Kernel driver in use: wl

    Read the article

  • Nvidia driver overscan issue second monitor via dvi-d cable

    - by benmichael
    Ok, I know that I have a bit of a bizarre setup, but here goes. I have an old laptop, HP Pavilion 6000. The graphics card in there is a GeForce 7150M. The monitor connection is an old 18pin. The external monitor I use is a Samsung SyncMaster 2333. Don't ask me why, but this monitor only has a dvi-d connection (yes, i have searched it). So I have the monitor plugged into the laptop. If I use any of the Nvidia propriety drivers and try to set the resolution up to 1920x1080 (the monitor's native resolution), I get a massive overscan issue. Over the years I have tried to get this to work, tinkering with my xorg.conf to death. I have also tried this on every Ubuntu since 10.04, on all the corresponding LUbuntus, and on all the Linux Mints since Lisa. Exact same issue. I have even tried it in WinDoze and it works perfectly there (although I did get the error once, but was unable to reproduce it). Using the Open Source drivers it works perfectly iff I switch off the laptop monitor (this makes no difference with the Nvidia drivers). I would have happily gone on using the Open Source drivers, except that since upgrading to LUbuntu 12.10, the Open Source drivers make my monitor completely hazy and have the same overscan issue until I (through the haze, only because I know where things are) go to the monitor settings, activate the laptop's monitor, then deactivate it, and suddenly it comes right. I have to do this every time. So I have to find a way to fix one of them, so I may as well tackle the propriety drivers, hence this overlong question. Amidst other things, I have tried the nvidia-settings, but because it is connected to an 18pin, it detects the monitor as a vga monitor and does not give me overscan correction options. I have tried custom modlines (although there are always more of those try), I have tried using xrandr, and I have tried all the FlatPanelOptions. What I have not tried is a Gentoo build, as I don't have time any more to do that installation, but up to about three years ago when I ran Gentoo exclusively I did not have this issue. Below is an link to an image with a red highlight around the portion of the screen visible to me, the numbers around it are the number of pixels which are cut off. This does seem to drift a few pixels every now and then. Thanks in advance. Nvidia driver issue image

    Read the article

  • Scanning for digital cable on me-tv

    - by Jared
    I have a pinnacle pchd 800 USB tuner that I want to use with Me-TV. I can't figure how to get it to scan for digital clear cam channels though, I've tried the standard cable frequency option and it didn't get anything. I'm in the U.S. and have Time Warner cable.

    Read the article

  • Using an audio cable (or similar) to create unidirectional communication from a secure server

    - by makerofthings7
    I'm interested in exploring how a semi-offline Root CA can be used to update CRLs to the sub CA's. This answer on Security.SE mentions using an audio cable for this purpose. Doe anyone have details on how an Audio cable (or similar) can be used to create a unidirectional path of communication? Since I'm a .Net programmer, I'm also open to code samples, drivers, etc that may enable this scenario.

    Read the article

  • Routing multiple static IPs from ISP at the cable modem?

    - by Jakobud
    I'm taking over IT responsibilities for a previous IT guy. We have a 50mb cable modem connection from Comcast along with 5 static IP addresses: XXX.XXX.XXX.180 XXX.XXX.XXX.181 XXX.XXX.XXX.182 XXX.XXX.XXX.183 XXX.XXX.XXX.184 We are in the process of replacing our firewall machine. Currently the firewall box is the only thing connected to the cable modem. However the cable modem has multiple ethernet ports on it, similarly to a router. I have assembled a new firewall machine and its time to start testing and configuring it. So that means that I also need it plugged into the cable modem (remember it has multiple ethernet ports on it). So now with multiple computer plugged into the cable modem, how does the cable modem know where to route the traffic? If some request on the internet is made to XXX.XXX.XXX.181, which goes to our cable modem, how does the cable modem know which connected computer that traffic is supposed to be sent? Looking at the web interface for the cable modem, there doesn't seem to be anything special setup on it with regards to routing or NATing IP addresses. Is that because when there is only one computer connected to the modem, all traffic is sent to it by default? Now that I am going to (temporarily) have multiple computers plugged into the cable modem, do I need to specify routing or NAT rules on the modem itself? I am going to speak to Comcast about this next, but I figured I'd ask here first just so I can get a better grasp on how this type of thing generally plays out.

    Read the article

  • kvm-over-ip, multiple machines per cable run

    - by Sirex
    I'm looking at getting a kvm-over-ip setup for a server room. Typically these devices have 16 or so cat5 leads that come out of them and then a convertor that converts each cat5 into a vga & ps2 pair. Can you run one cable from the unit into a switch, and then leads from the switch into each machine ? I have several machines on the other side of the server room that i'd like to have avaliable but i dont want to run 16 cables to them. I'm thinking this should be possible being IP layer and all, but as each device normally has its own cable out the back of the kvm unit i'm not certain. Perhaps the kvm's rear ports act essentially like a switch anyway in which case it should work, or perhaps if i run all 16 cables into a seperate switch right next to it and aggregate the ports together, run one cable to a switch on the other side of the room with similar number of ports agregated together, then use that switch to plug each macine into ? I'm fairly sure this is possible, but i just want to check before i shell out the cash as i've never tried it.

    Read the article

  • unable to access Internet by wireless but can by cable

    - by Jeff King
    i'M GOING MAD! UNtil last friday I had been successfully using wifi with the supplier as VIRGIN through their Motorola SB 4200 cable Modem and the wireless router being the Linksys WRT 54G router. Supported were three lap tops and an EPSON 510W printer and this had been running with no issue for about 3 years. Back to last friday, we started suffering significant delays and then the network collapsed with no wireless access. I was able to connect a single laptop direct to the cable modem and internet access was restored to just that one device. I thought that the problem was the router so I tried a backup D-Link device with no success. I have subsequently bought another cable modem AND a netgear router plus addidtional ethernet cables but with no success. The best that happens is that the signal appears good but I cannot get access to the internet. A yellow question mark appears on the 'gradient' icon. Each laptop and router works elsewhere so I'm stumped. Mind you I am a real novice so I'm not surprised. Please can anyone tell me what I'm doing wrong?

    Read the article

  • Obtaining clear cable signal with Hauppage 1191-950Q TV Tuner

    - by Kyle B.
    I bought a Hauppauge 1191 WinTV-HVR-950Q TV Tuner a while back, and I am attempting to use it to watch TV in Windows Media Center. I do not have cable TV, however I used to have Comcast. Through experimentation, I found that connecting my coax cable into my TV, I was able to view television (i.e. 2-1 = CBS, 5-1 = NBC, etc). This also works on a second TV I use in another room. When I connect the coax cable to my TV Tuner stick and scan TV channels in Windows Media Center, it only picks up 1 station (like 81 or something). My only conclusion on this is somehow the hardware in the television is decrypting a signal that the TV tuner stick is not able to. Is that possible? Should I try a different TV tuner? Any assistance would be appreciated. I also bought a Terk HD Indoor Antenna but my reception has been flakey, so I would rather go this route if possible.

    Read the article

  • Network outage caused by SMC8013WG Cable Modem/Router ?

    - by mkocubinski
    At work, we have a basic Class C Network. The gateway/router is a SMC8013WG (stock comcast commercial cable modem), and simple unmanaged switch (HP Pro Curve 1400 24G). The SMC8013WG is our default gateway as well as DHCP server. Periodically, I'd say almost every other day.. the entire network will just stop responding. I won't be able to ping/see the gateway, any computers on our local network, or anything on the internet. The only way to fix this is to unplug the Comcast cable modem, wait, and plug back in. This unfailingly fixes the problem. But this doesn't make much sense to me.. shouldn't the network still be fine locally, since everything is plugged into the switch anyway? Why would resetting the router fix this? Can anyone suggest anything to check to in order to narrow this problem down? Just to be clear.. here is the basic topology: { Internet } -- (12.345.67.89) Comcast Cable Modem (192.168.1.1) -- Switch -- 192.168.1.2-254 P.S. Our IT guy is in about 3 hours a day every other week or so, so.. we're kind of on our own most of the time.

    Read the article

  • Older monitor not working with HDMI to DVI cable (from ultrabook)

    - by ShellfishGene
    I have a Lenovo Yoga ultrabook which only has a HDMI port. I bought an HDMI to DVI cable, and it works as expected with a LG monitor in my office. As soon as I plug it in the screen is cloned. At home I have an older Dell UltraSharp 2005fp, and for that one it does not work. When I plug the cable in "something" happens, the monitor goes from the "no signal" screen to black. On the laptop however nothing happens. In the Windows 8 display setup I don't have another monitor, clicking "detect" does not find one either. I can manually set a second display for cloning or extending, but never get a picture on the Dell. Connecting my media player thing with the cable to the Dell monitor works for when the player displays it's logo at a low resolution, but when it goes into 750p mode after booting the picture also goes away. Mabye that's due to HDCP though. Any ideas? Something to do with Windows 8, or DVI versions?

    Read the article

  • IP Micro-outages, telephone micro-outages, and CATV micro-outages

    - by Michael Graff
    This is a long and complicated question, mostly because it has been going on for 2.5 years without a solution in sight. It also is only one-third computer related, the other two-thirds are cable TV and cable-phone related. Background I have COX Communications for a cable provider, and we get Internet, digital cable TV, and digital phone service through them. The Internet is a SB5101 right now, and has been a DPC2100 and SB5120 in the past. Same results. The phone service is provided through a telephone interface mounted on the outside of the house (not classic VoIP) and the CATV is through a Scientific Atlanta receiver without DVR. I do have a TiVo connected to the CATV box. Symptoms The CATV shows "blocking" -- sometimes very very short duration where a few blocks appear on the screen. Sometimes it lasts long enough that the video "pauses" for 2-5 seconds, and rarely but not unseen the audio also fails. The CATV decoder box shows no correctable (FEC) or uncorrectable errors. That is, all BER counters are zero for the video stream. The Internet shows "micro-outages" where it appears that sent packets are not making it out, but I continue to receive packets from local modems. That is, pings stop coming back, but I continue to see modems broadcast for DHCP, and sometimes they ask more than once. The cable modem shows no errors during this time, but cable modems lie like you would not believe. It is actually possible to unplug the coax from the modem for 20 seconds and it reports NO ERRORS to the provider's tools. The phone service cuts out for 1-3 seconds, infrequently. When this happens, I hear NOTHING (not even comfort noise) and the remote side hears a "click" as if I were getting a call waiting message. However, there is no call incoming, other than the one I'm currently on of course. Things SEEM to happen more frequently when the temperature outside swings from cold to warm, so fall/spring seems worse than summer/winter. All micro-outages occur between once or twice a day (which I could ignore) to 10 times per hour. All SNR, signal levels, noise levels, etc. show very close to optimal when measured. COX's diagnosis This is a continual pain for me. Over the last 2.5 years, they have opened, "fixed" something, and closed the tickets. They close it without confirming that it is indeed better, and when I reopen they cannot do that, but instead they open a new ticket and send yet another low-level tech out to do the same signal tests and report that all is OK. I've finally gotten a line tech who has a clue and is motivated enough to pursue this with me. We have tried things like switching the local nodes over to UPS and generator power, but this does not trigger the noise. We have tried replacing all cabling, the tap outside my house, the modem, the CATV decoder -- all without resolution. Recently they have decided it is both my computer or switch, my TiVo, and my phone that are all broken and causing this issue. My debugging steps I spent the worse day of my TV-watching life yesterday and part of today. I watched live TV without the TiVo. I witnessed blocking, but it did "feel different." and was actually more severe. Some days it is better, some days it is worse, so perhaps this was just a very bad day. Today, I connected the TiVo to my DVD player, and ran two very long movies through it. I saw no blocking at all during nearly 6 hours of video. Suggestions? Does anyone have any suggestions on what to do next? I understand perhaps only the IP side can be addressed here, but it is one of the more limiting debugging options.

    Read the article

  • USB Serial cable with CDC support

    - by Harsha
    Hi All, I bought a USB to Serial cable which claims to be CDC compliant. But the bInterfaceClass value in interface descriptor is 0xFF(which is vendor specific). I was expecting it to be 0x02 (Communications and CDC control). In the device manager, i found that the drivers being loaded are ser2pl.sys and serenum.sys. I had learnt usbser.sys is the windows CDC driver, but it was not loaded for my cable. I am pretty much new to this CDC, so i have following questions 1.Does this indicate that the cable is not CDC compliant 2.Can i make this cable CDC compliant (since CDC is a driver functionality), by loading usbser.sys. If yes how?

    Read the article

  • Access / Excel crossover: Should i attach spreadsheets to records

    - by glinch
    Hi, I currently have an archaic system of client records that I am trying to improve. For each client i have a directory, in that directory i include a directory for each job. Each job has a spreadsheet that i use to store their personal details, and run calculations and costings specific to their needs. In turn I also have word documents that are linked to their spreadsheet which automatically update accordingly. The spreadsheet is also exported as a pdf as well I am trying to build a database of customer records in Access, straight forward enough. For each new customer i need to be able to add the appropriate spreadsheet to their records, update the spreadsheet accordingly with their details, use the spreadsheet to calculate their costings etc.. I do not want to enter the same information repeatedly, and would like a cohesive system, with data being passed between access and excel. Should this be easy enough to do with the two packages? Thanks in advance Noel

    Read the article

  • How to connect to a Virtualbox guest from the host when network cable unplugged

    - by Greg K
    I'd like to work offline (I'm flying to the US twice this month), to do this I need access to a linux development server. When I work from home I boot a VirtualBox VM and that acts as my dev server for the day (providing Apache, PHP & MySQL to run my server side code). However, I'd like to work with my VM when I'm not connected to a network. I have my Ubuntu VM guest set up with a bridge connection so it can serve HTTP and provide SSH access from inside my local network. I've tried to manually configure my network settings on both Mac OSX (the host) and Ubuntu (the guest) but I can't even ping my own NIC address (127.0.0.1 can, 192.168.21.x I can't) in OS X when I unplug the cable. Manual network settings: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx inet 192.168.21.5 netmask 0xffffff00 broadcast 192.168.21.255 media: autoselect (100baseTX <full-duplex,flow-control>) status: active I can ping localhost fine, as well as my VM (.20) and SSH too. $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes 64 bytes from 192.168.21.5: icmp_seq=0 ttl=64 time=0.085 ms 64 bytes from 192.168.21.5: icmp_seq=1 ttl=64 time=0.102 ms 64 bytes from 192.168.21.5: icmp_seq=2 ttl=64 time=0.100 ms 64 bytes from 192.168.21.5: icmp_seq=3 ttl=64 time=0.094 ms $ ping 192.168.21.20 PING 192.168.21.20 (192.168.21.20): 56 data bytes 64 bytes from 192.168.21.20: icmp_seq=0 ttl=64 time=0.910 ms 64 bytes from 192.168.21.20: icmp_seq=1 ttl=64 time=1.181 ms 64 bytes from 192.168.21.20: icmp_seq=2 ttl=64 time=1.159 ms 64 bytes from 192.168.21.20: icmp_seq=3 ttl=64 time=1.320 ms Network cable unplugged: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx media: autoselect status: inactive $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes ping: sendto: No route to host ping: sendto: No route to host Request timeout for icmp_seq 0 ping: sendto: No route to host Request timeout for icmp_seq 1 Does OS X disable the NIC when the network cable is unplugged? Any way to stop it doing this?

    Read the article

  • File sharing from a cable connected pc to wifi connected laptop (windows 7 ultimate)

    - by Aiden Jones
    I have a one desktop running windows 7 ultimate connected to Ethernet cable. And I want to share folder to another wifi connected laptop (also windows 7 ultimate). Both machines are on the same home internet connection. I have tried to share folders by going to properties sharing advanced sharing permissions checked all the boxes to allow all but I don’t see any shared files on my laptop. I know it’s possible to share folders between two Wi-Fi connected machines but how can it be done when one pc is cable connected and other is Wi-Fi connected on the same internet connection.

    Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >