Search Results

Search found 2799 results on 112 pages for 'hp ux'.

Page 6/112 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

  • Generic socket 940 CPU fan for HP XW9300 interchangeable with HP part number 411454-001

    - by ConcernedOfTunbridgeWells
    Hi, I'm trying to find a generic Socket 940 CPU fan that will fit the air duct in an XW9300. Note that two different CPU fan mounting schemes have been used on this machine. One has two grommets in the motherboard that the CPU fan screws into and the other has a plastic collar and base plate. The form factor I'm looking for is the former (see the picture below). Two HP part numbers for fans in this form factor are 411454-001 (shown below) and 416055-001. Note that the dimensions are important as the machine has an air duct that fits over the fan. Can anyone tell me the manufacturer and model of an equivalent generic part? Better yet, do you know somewhere (preferrably in the UK) from which such an item can be obtained?

    Read the article

  • How do I turn on wireless adapter on HP Envy dv6 7200 under Ubuntu (any version)?

    - by Dave B.
    I have a new HP Envy dv6 7200 with dual boot Windows 8 / Ubuntu 12.04. In windows, the F12 key in Windows activates the "airplane mode" switch which enables/disables both on-board (mini PCIe) and USB wireless adapters. In Ubuntu, however, the wireless adapter is turned off by default and cannot be turned back on via the F12 key (or any other combination of F12 and Ctrl, Fn, Shift, etc.). Let me explain the "fixes" I've seen in various forums and explain what did or did not happen. These are listed in no particular order. (Spoiler alert: wireless is still broke). Solution 1? Use HP's "Wireless Assistant" utility to permanently activate the wireless card in Windows, then boot into Ubuntu to happily find it working. Unfortunately, this utility works in Windows 7 but not Windows 8. On the other hand, hardware drivers from HP are only available for Windows 8 for this model. Catch 22 (I could not find a comparable utility for Windows 8). Solution 2? Use a USB wireless adapter to sidestep the on-board device. I purchased such a device from thinkpenguin.com to be sure that it would be Linux-friendly. However, the wireless switch enables / disables all wireless devices including USB. So, there's my $50 donation to the nice folks at thinkpenguin.com, but still no solution. Solution 3? Following the Think Penguin folk's suggestion, modify the mini PCI express adapter following instructions here: http://www.notebookforums.com/t/225429/broken-wireless-hardware-switch-fix Tempting, but I then violate the terms of my warranty mere days after opening the box. This might be a good solution for an older machine that you want to get your geek on with, but not for a new box. Solution 4? rfkill unblock all No effect whatsoever. ubuntu@ubuntu-hp-evny:~$ rfkill unblock all ubuntu@ubuntu-hp-evny:~$ rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Solution 5? Re-install drivers. Done and done. Ubuntu recognizes the device - perhaps even without re-installing the drivers? - but cannot turn it on. How do I know this? In the Network Manager drop-down menu, the wireless option is blacked out and a message reads something like: "wireless network is disabled by a hardware switch". Solution 6? Identify a physical switch on the laptop and flip it. There is no such switch on this machine. In fact, walking through Best Buy yesterday, I checked and not a single new laptop PC had a physical switch on it. All of the wireless switches are either the F2 or F12 key ... I wonder if askubuntu will not be plagued by this exact issue in the near future? Additional info - lspci ubuntu@ubuntu-hp-evny:~$ lspci 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5229 (rev 01) 0a:00.0 Network controller: Ralink corp. Device 539b 0b:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Any suggestions would be much appreciated!

    Read the article

  • User Experience Tablet Guide Released on UX Direct Site

    - by Madhuri Kolhatkar
    Tablet Guide available on UX Direct NOW Responding to a popular demand from our customers, Oracle Application's user experience team is happy to externalize its new design guide for creating tablet based solutions for Enterprise applications on the UX Direct website. Download and use this guide to create great and successful customer experience for your users. UX Tablet Guide for Oracle Applications This guide provides basic help for designers, developers, and project managers trying to approach tablet design and testing from an enterprise point of view. If you are embarking on a tablet application design project, start here first. In the spirit of tablet design, it is delivered in the form of an iPad interactive iBook .Use this guide and tell us what you think. We would love to see examples of your creations. Watch this space for more updates and new and innovative design tools.

    Read the article

  • Ubuntu + Raid on HP proliant DL 160 G6

    - by Adam Matan
    Hi, I'm, trying to install Ubuntu 8.04 Server on an HP Proliant DL160 G6. The HP hardware is certified by Ubuntu for the 9.04 version, which I can't install due to company policy. The problem is that Ubuntu would not recognize the RAID 1+0 disk configured by the BIOS. The raid creates one ~470GB disk from two 500GB physical disks. Any ideas? Adam

    Read the article

  • Proliant Support Pack and Ubuntu on older HP Proliants

    - by snl
    We have a couple of oldish HP Proliant servers -- one DL385 G1 and one DL360 G5, to be exact -- that we'd like to upgrade from CentOS 5 to Ubuntu LucidLynx. The problem is that HP doesn't offer Ubuntu Proliant Support Packs for these particular models. Would you upgrade regardless, skipping the PSPs altogether? Are there alternative hardware monitoring tools that would match the functionality of the PSPs? Is there a hack to install the PSP RPMs on an Ubuntu system?

    Read the article

  • HP blade server: How many connection can be made between HP new gen 8 blades and an interconnect

    - by Dave T
    I am building a virtualized network on an HP C3000 with 460c Gen 8 blades and 2 HP L3 switch interconnects. I was advised to by a 1Gb 4-port 366M Mezzanine Adapter. That provides me 6 ethernet connections to each blade. I have been told that you can only make 2 connections to from each blade to each interconnect, but since I have to interconnectes and 6 ports I hope someone can tell me if I can make 3 connections from each server to each interconnect. I looking for the actual - thanks Dave

    Read the article

  • HP Proliant Servers - WMI query for system health

    - by Mike McClelland
    Hi, I want to query lots of HP servers to determine their overall health. I don't want to use any packages, or even SNMP - I want to query the server health from WMI and understand if a box is Green/Amber/Red - just like the HP Management Home Page. This MUST be possible - but I can't find any documentation... Oh yes, and the servers are running Windows Server 2003/8. Help!! Mike

    Read the article

  • NDMP NAS for HP EVA4400 SAN

    - by Sergei
    We use EMC Celerra filer for our EMC array and it supports NDMP.n remote site we have EVA4400 HP SAN and it seems that our only option for NAS is Windows Storage Option. What if we want to use NDMP?Surely HP should have something that match Celerra?

    Read the article

  • No video output and no status light on HP Proliant Microserver

    - by tombull89
    I have an issue with a "N40L" HP Proliant Microserver. When the server is powered on the power light turns green but the machine's status light (the HP logo on the front) stays off and there is no video output through th onboard VGA. The system fan kicks in and if connected to a network the link light shows activity. I have no extra boards (iLO card, graphics card) only 4GB PNY non-standard stick of RAM.

    Read the article

  • Apps UX Unveils New Face of Fusion at OpenWorld 2012

    - by Kathy.Miedema
    By Kathy Miedema, Oracle Applications User Experience The Oracle Applications User Experience (UX) team is getting ready to unveil the new face of Oracle Fusion Applications at Oracle OpenWorld 2012 in San Francisco next week. Photos by Martin Taylor, Oracle Applications User ExperienceJeremy Ashley, Vice President of Oracle Applications User Experience, shows the new face of Fusion Applications to a group of trainers at Oracle’s headquarters in Redwood Shores, Calif. Our team spent the past 6 months working on this project, which embraces simplicity with a modern, productive user experience that aims to help our applications customers rapidly scale deployment of essential self-service tasks and speed adoption by users who need quick access to do quick-entry tasks. We have spent the week before OpenWorld at Oracle headquarters in Redwood Shores, conducting training sessions with Fusion UX Advocates (FXA), Oracle UX Sales Ambassadors (SAMBA), and members of the Oracle Usability Advisory Board (OUAB). We showed the new face of Fusion to customers, partners, ACE Directors, and people from our own sales organization. Next week during OpenWorld, they will be showing demos alongside our team members. To find them, look for the Usable Apps t-shirt, with this artwork: You can also get a look at the new face of Fusion during OpenWorld at the following sessions and demopods: GEN9433 - General Session: Oracle Fusion Applications—Overview, Strategy, and Roadmap Presenter: Chris Leone, Senior Vice President, Oracle Monday, Oct. 1, 10:45 a.m. – 11:45 a.m. in Moscone West 2002/2004 AND Wednesday, Oct. 3, 10:1 a.m. – 11:15 a.m. in Moscone West 2002/2004 CON9407 - Oracle Fusion Customer Relationship Management: Overview/Strategy/Customer Experiences/Roadmap Presenter: Anthony Lye, Senior Vice President, Oracle Monday, Oct. 1, 3:15 – 4:15 p.m. in Moscone West 2008 CON9438 - Oracle Fusion Applications: Transforming Insight into Action Presenters: Jeremy Ashley, Vice President Applications User Experience, Oracle; Katie Candland, Director Applications User Experience, Oracle; Basheer Khan, founder and CEO of Innowave Technology, an Oracle ACE Director for both Fusion Middleware and Applications, and a Fusion UX Advocate Tuesday, Oct. 2, 10:15 a.m. - 11:15 a.m. in Moscone West 2007 CON9467 - Oracle’s Roadmap to a Simple, Modern User Experience Presenter: Jeremy Ashley, Vice President Applications User Experience, Oracle Wednesday, Oct. 3, 3:30 p.m. - 4:30 p.m. in Moscone West 3002/3004 On the demogrounds: Come to the Apps UX pods for a look at enterprise applications on mobile devices such as smart phones and the iPad, and stay for a demo of the new face of Oracle Fusion Applications. Our demopods will also feature some of the cutting-edge tools in Oracle’s arsenal of usability evaluation methods. The Exhibition Hall at Oracle OpenWorld 2012 will be open Monday through Wednesday, Oct. 1-3. The demogrounds for Oracle Applications are located on the lower level of Moscone West in San Francisco. Hours for the Exhibition Hall are: · Monday, 10 a.m. to 6 p.m. · Tuesday, 9:45 a.m. to 6 p.m. · Wednesday, 9:45 a.m. to 4 p.m.

    Read the article

  • HP P212 hangs on Initializing

    - by user927586
    I'm in trouble... Server: HP Microserver N36L Storage: HP P212/256 with BBWC Drives: 4 WD 2 Tb While expanding the RAID 5 array from 3 to 4 drives, the server rebooted itself. Expansion was at 76%. Now at boot the P212 seems to hang on initializing. After some time screen resets and the server boots, but in the os (Windows Server 2008R2) the P212 has errors (error code 10) and it's not seen by the HP ACU. Whats' going on? It's trying to complete the expansion? It's trying to make all over the expansion? It's simply stuck? What should I do? I NEED the data on the array! PS In the server BIOS, on the hd boot priority, the server still reports the array logical drive... maybe it's a good sign... PPS I'm not at the server physical location, so I cannot tell if the drives in the array are being accessed (that would be the case if the controller it's redoing/completing the expansion process) or not right now. Bye Dario

    Read the article

  • Problem setting up HP PhotoSmart C4783

    - by ProfKaos
    I am trying to get several PC's on a network to connect to my client's new wireless printer, the C4783. I initially installed the whole HP 'tsumami of software' the comes with the printer onto my laptop, connected to the printer over USB, and corrected it's networking config. My laptop now also can connect to and print on the printer over the wireless network, as is intended for all PC's. However, when I try and install the HP software on my client's netbook, the HP software cannot find the printer. Firewall was turned off during this time, so doesn't play a role. I tried re-installing all software, but I initially only got a "Repair" or "Uninstall". Choosing Uninstall triggers a lengthy process that ends with a sudden and forceful restart, after which the same "Repair" or "Uninstall" choices are present. Looks like uninstall doesn't. Any suggestions as to how I can begin diagnosing why my laptop has no problem connecting to the printer, but two others do? Wireless is unsecured, and no, nobody has to know where I am right now. :-)

    Read the article

  • HP Pavillion DV6500 recovery disk failure

    - by Scott W
    I recently attempted to re-install Windows Vista on an HP Pavillion DV6500 using the factory recovery DVD's, but encountered a strange problem. When the recovery disk attempted to reformat the hard disk, it failed at 22%. The error message provided was not very informative, just the error code "0x400110020000 1005". A google search turned up some people with a similar problem who asserted that HP has been know to ship corrupted recovery DVDs. The recovery disk did manage to reformat the the recovery partition before failing though, so recovering from the partition is no longer an option. It would be possible to reinstall from an off-the-shelf retail copy of Vista and then pull the drivers from HP's website, but I don't have access to a copy of Vista, and it would really be outrageous to have to purchase a new OS when I have a perfectly valid license already. Thought about biting the bullet and upgrading to Windows 7, but my understanding is that without Vista installed I'd be unable to use the upgrade version, and be forced to purchase the more expensive non-upgrade retail copy (!). Can anyone suggest a possible solution to this Catch-22? I've run out of ideas.

    Read the article

  • hp proliant dl360 disk diagnostic issue

    - by user1039384
    We recently got two used drives (15000) and installed on our HP proliant dl360 G5 server. Created RAID1 and used HP SmartStart CD to perform diagnostics. Interestingly, the Diagnostic tab immidiately fails on Logical drive testing saying the Disk1 should be replaced, while the Test tab successfully runs all the complete tests on both disks and does not find any issue. At the meantime, when booting to esxi 5, vSphere periodically shows the Disk1 as Unknown and Logical drive in recovery process. This happens every 5-10 minutes. Here is the log from HP SmartScan diagnostic: 1 - Device, Test: Logical Drive 1, Storage Controller in Slot 0 1 - Description: The controller has reported a critical error in the drive error log. 1 - Recommended Repair: This drive should be replaced. 1 - Failed Count: 44 1 - Error code: F157 There is also another error log record (see below): 2 - Device, Test: test_components/libstorage.so ID 2 - Description: An unexpected exception occurred while performing an operation. Exception message: CISS_StatusHandler::evaluate: commandStatus = 4 (INVALID); hexdump of CISS_ErrorInfo: 00000000: __ __ 04 __ 20 __ __ __ __ __ __ __ __ __ __ __ .... ... ........ 00000010: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ 00000020: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ Device: Hard Drive 2, Storage Controller in Slot 0 Property name: Bad Target Count 2 - Recommended Repair: Reboot or restart Insight Diagnostics. Retry the test. If the problem persists, upgrade to the latest version of Insight Diagnostics. 2 - Failed Count: 48 2 - Error Code: F62 Note that rebooting didn't help and I was running the latest diagnostic software version. Anyone has a clue? Is this a real disk issue? BTW, the controller is Smart Array E200i Thanks in advance

    Read the article

  • HP DL185 - very slow disk read speed

    - by fistameeny
    Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

    Read the article

  • HP Pavillion DV6500 recovery disk failure

    - by Scott W
    I recently attempted to re-install Windows Vista on an HP Pavillion DV6500 using the factory recovery DVD's, but encountered a strange problem. When the recovery disk attempted to reformat the hard disk, it failed at 22%. The error message provided was not very informative, just the error code "0x400110020000 1005". A google search turned up some people with a similar problem who asserted that HP has been know to ship corrupted recovery DVDs. The recovery disk did manage to reformat the the recovery partition before failing though, so recovering from the partition is no longer an option. It would be possible to reinstall from an off-the-shelf retail copy of Vista and then pull the drivers from HP's website, but I don't have access to a copy of Vista, and it would really be outrageous to have to purchase a new OS when I have a perfectly valid license already. Thought about biting the bullet and upgrading to Windows 7, but my understanding is that without Vista installed I'd be unable to use the upgrade version, and be forced to purchase the more expensive non-upgrade retail copy (!). Can anyone suggest a possible solution to this Catch-22? I've run out of ideas.

    Read the article

  • HP LaserJet 1515: Disable "refill" warning

    - by Pekka
    I have a HP LaserJet 1515 connected to a Windows 7 PC. The Magenta cartridge is empty; the printer shows a warning to that effect, and won't let me print even black-and-white documents any more. I can't turn the warning off manually using the printer's small console: When I try to enter any menu, the display says "Menu access disabled". I have no idea why. There is a setting to override the warning, but it can't be changed using the Network interface in the browser (Although it is there on the status page) According to the manual,the HP printing tool is supposed to offer a switch for this, but it won't install on my Windows 7. It just rumbles about for half an hour, to magnificently exit with an "unknown error" requiring a reboot. On second look, the problem seems to be that Windows 7 just isn't supported. There is no download link for the tool when you specify Windows 7 as your OS. I just want to print a black-and-white-document on a printer whose black cartridge is still 65% full. Is this indeed impossible? On second thought, I'm cross-posting this on the HP support forum. I'll update here if anything comes up.

    Read the article

  • hp ProLiant DL380 G6 server error code: 347 of array controller

    - by alhaythum
    I have got a bran new hp ProLiant DL380 G6 server with embedded smart array P410i controller, I got 164 GB SATA drives and wanted to change them with 300 GB SATA drives before installation. Now, we replace the drives and begin the configuration with the hp DVD and begin; when we reach the point that we want to save the configurations, an error message appears: "The operation has failed with an unknown error, please restart the application and attempt the operation again" When using Rescan System, this error message appears: "Status Alerts - Smart Array P410i in Embedded Slot Warning Status Message Code Description 347 The cache for Smart Array P410i Embedded Slot is not configured" We return back to the 164 GB SATA drives and the message just keeps appearing again. Any help please.

    Read the article

  • How HP D2700 disk enclosure is monitored for alarms via SNMP

    - by VSAC
    We have HP D2700 disk enclosure and we would like to monitor D2700 (connected to HP Proliant DL360G8) for alarms.I have following questions regarding this. What are the options available for reporting D2700 hardware alarms (disk failure, power failure) via SNMP? We understand the D2700 to have an Ethernet interface for controller A and B and alarms are available via SNMP via this interface. Can anyone provide the actual alarms via this interface? (MIB and alarm list) As we have a number of D2700’s and would like to minimize the number of physical connections to the switch and associated IP addresses; Is there a mechanism to monitor the D2700 from the SCSI connected HPDL360 and raise SNMP alarms from the DL360 for hardware failures on the D2700? If so can anyone provide details and the actual alarms and MIB via this mechanism? Thanks!

    Read the article

  • HP Blade ILO not responding in chassis ILO

    - by bobinabottle
    I have just started at a new company and I am inspecting their current server config. The HP 480c blades in a c7000 chassis aren't responding to ILO, although the chassis ILO is working fine. I have a feeling the last sysadmin configured the blades ILO as static IPs and it is not responding correctly. The servers are sitting in a datacenter and I'm hoping to be able to fix this remotely. Is there a way that I can change the ILO static IPs for the blades remotely? If not and I do have to go onsite, how do I change the IP addresses of the ILO for the blades? (Sorry I'm not very familiar with HP servers) thanks for you help!

    Read the article

  • Creating a dynamic lacp trunk from HP Procurve 2412zl to Proliant DL380 G7

    - by Maalobs
    I'm configuring an IEEE 802.3ad (LACP) dynamic trunk from a HP Procurve 2412zl (firmware version K.15.07) switch to a HP Proliant DL380 G7 server. The DL380 has 4 NICs and is running Win2008 R2, so I'm teaming the NICs together and leaving everything on the recommended "automatic" setting in the HP NIC configuration tool. The server is one of two, they'll be connected on interfaces F17-F20 and F21-F24 respectively on the switch. I need the servers in a separate VLAN, here is the configuration for the VLAN: vlan 10 name "Lab_Mgmt" untagged B2,F17-F24 ip address 172.22.71.3 255.255.255.0 tagged B21 exit There is a DHCP-relay into the VLAN 10 from another device beyond interface B21. The Advanced Traffic Management Guide says that in order to run a dynamic LACP trunk on another VLAN besides the DEFAULT_VLAN, you need to first enable GVRP and then use "forbid" to stop the interfaces from automatically joining DEFAULT_VLAN when the dynamic trunk is created. GVRP brings some other stuff with it that I don't want or need, so I disable it with "unknown-vlans disable" on all other interfaces. Here is how I do it: procurve-5412zl-1(config)# gvrp procurve-5412zl-1(config)# interface A1-A24,B1-B24,C1-C24,D1-D10,D13-D24,E1-E24, F1-F16,K1,K2 unknown-vlans disable procurve-5412zl-1(config)# vlan 1 forbid F17-F24 procurve-5412zl-1(config)# interface F17-F20 lacp active The result afterwards looks all successful: procurve-5412zl-1(config)# show trunks Load Balancing Method: L3-based (Default), L2-based if non-IP traffic Port | Name Type | Group Type ---- + -------------------------------- --------- + ------ -------- F17 | XYZTEAM3_NIC1 100/1000T | Dyn2 LACP F18 | XYZTEAM3_NIC2 100/1000T | Dyn2 LACP F19 | XYZTEAM3_NIC3 100/1000T | Dyn2 LACP F20 | XYZTEAM3_NIC4 100/1000T | Dyn2 LACP procurve-5412zl-1(config)# vlan 10 procurve-5412zl-1(vlan-10)# show lacp LACP LACP Trunk Port LACP Admin Oper Port Enabled Group Status Partner Status Key Key ---- ------- ------- ------- ------- ------- ------ ------ F17 Active Dyn2 Up Yes Success 0 0 F18 Active Dyn2 Up Yes Success 0 0 F19 Active Dyn2 Up Yes Success 0 0 F20 Active Dyn2 Up Yes Success 0 0 On the Proliant server, the NIC configuration Tool is also indicating that a 802.3ad dynamic trunk has been established. Everything should be good, but it isn't. The server is not getting an IP-address from the DHCP, which it does if I'm not enabling LACP. If I configure the server to a static IP-address on the VLAN 10 subnet, it can't even ping the switch IP-address, much less anything outside of the VLAN. The switch can't ping the server either. I did another attempt with F17-F20 tagged, and checking the box "Default Native Tag (VLAN 10)" in the NIC configuration tool on the server, but there was no difference. Does anyone have any idea what I might have missed?

    Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >