Search Results

Search found 186 results on 8 pages for 'manuals'.

Page 6/8 | < Previous Page | 2 3 4 5 6 7 8  | Next Page >

  • Does the Intel DX79TO motherboard support x8 devices (SAS HBAs) on PCIe x16 slots?

    - by Zac B
    Context: I have an Intel DX79TO motherboard and a Sun SAS3081E-S/LSI 1060E-S HBA card with a PCIe x8 interface. I plug the HBA into my mobo next to my graphics card, and the HBA power lights illuminate, but the BIOS and OSes (tried Linux, ESXi, Win7) don't see the HBA at all. Question: Does the DX79TO motherboard support non-x16/non-GPU devices in its PCIe x16 slots? According to this question, some consumer motherboards don't support this, but I can't figure out whether or not this motherboard/family does. The answer will affect whether I buy a new motherboard or RMA the SAS card, with money attached to each course, so I figured I'd ask here first. What I've Tried: I've read the spec/manuals for the motherboard and the HBA, and I didn't see anything regarding whether or not the x16 slots were back-compatible to lower lane widths/non graphics-card devices, or whether or not the card could run in wider slots than x8. I've tried contacting Intel, but that was over a month ago and I haven't yet heard anything back except an automated "we got your email!" message.

    Read the article

  • Failed to mount to nfs server with "Program not Registered"

    - by Farrel
    I'm trying to setup nfs server on Fedora 17 and I'm getting "Program not Registered" error when I'm trying to mount. I guess the main reason for this is rpcbind. I'm a newbie in linux, so I don't know what info should I provide you with. Here is some info that might be useful. rpcinfo -p program vers proto port service 100000 4 tcp 111 portmapper 100000 3 tcp 111 portmapper 100000 2 tcp 111 portmapper 100000 4 udp 111 portmapper 100000 3 udp 111 portmapper 100000 2 udp 111 portmapper 100005 1 udp 20048 mountd 100005 1 tcp 20048 mountd 100005 2 udp 20048 mountd 100005 2 tcp 20048 mountd 100005 3 udp 20048 mountd 100005 3 tcp 20048 mountd 100024 1 udp 42223 status 100024 1 tcp 50054 status cat /etc/exports /home/Farrel/prog 192.168.xxx.xxx (ro,sync) service nfs status Redirecting to /bin/systemctl status nfs.service nfs-server.service - NFS Server Loaded: loaded (/usr/lib/systemd/system/nfs-server.service; enabled) Active: active (exited) since Fri, 02 Nov 2012 09:29:04 +0300; 5min ago Process: 924 ExecStartPost=/usr/lib/nfs-utils/scripts/nfs-server.postconfig (code=exited, status=0/SUCCESS) Process: 909 ExecStart=/usr/sbin/rpc.nfsd $RPCNFSDARGS ${RPCNFSDCOUNT} (code=exited, status=0/SUCCESS) Process: 885 ExecStartPre=/usr/sbin/exportfs -r (code=exited, status=0/SUCCESS) Process: 864 ExecStartPre=/usr/lib/nfs-utils/scripts/nfs-server.preconfig (code=exited, status=0/SUCCESS) CGroup: name=systemd:/system/nfs-server.service Warning: Journal has been rotated since unit was started. Log output is incomplete or unavailable. Firewall is disabled on both systems. I spent a lot of time reading on the topic but all manuals on setting up nfs server lead to "Program not Registered" error. Any how-to-fix-it ideas?

    Read the article

  • GnuPG Command Line - Verifying KeePass Signature

    - by Stisfa
    I'm trying to verify the PGP Signature of the latest version of KeePass 2.14's setup file against this signature, but this is the output I receive: C:\Program Files (x86)\GNU\GnuPG>gpg.exe --verify C:\Users\User\Desktop\KeePass-2.14-Setup.exe gpg: no valid OpenPGP data found. gpg: the signature could not be verified. Please remember that the signature file (.sig or .asc) should be the first file given on the command line. C:\Program Files (x86)\GNU\GnuPG> I found this command here, but it made no mention about ".sig" or ".asc" files, so I figured I did something wrong. By reading (http://www.gnupg.org/documentation/manuals/gnupg/gpgv.html#gpgv), I further tried the following: C:\Program Files (x86)\GNU\GnuPG>gpg.exe --pgpfile C:\Users\User\Desktop\KeePass-2.14-Setup.exe gpg: Invalid option "--pgpfile" C:\Program Files (x86)\GNU\GnuPG> As you can see, the results are quite obfuscating... I took a look at this on SuperUser (http://superuser.com/questions/16160/short-easy-to-understand-explanation-of-gpg-pgp-for-nontechnical-people - I couldn't use "a href" due to the built in spam filter that discriminates against users with < 10 rep; this is the same reason for the link above this link), but none of the links seemed to really address my question, at least not directly enough for me to get any idea on how to move forward on this. Can anybody here help me with the esoteric technicality of OpenPGP & the associated use of the GnuPG program? I've felt pretty dumb learning VBS, but this is beyond humiliating: it's absolutely debilitating and maiming whatever confidence I had with my IT skills (then again, I have no justification for making any boast either, as I have yet to get my A+ Cert, lol).

    Read the article

  • External USB HD with -optional- mains?

    - by Stephen
    Hi, I'm Christmas-present-buying, and I'd appreciate recommendations for a USB HD with an optional mains power input. I've hunted, but can't find all the information I want (partially due to sketchy product specifications). Background: This is for a digital TV which I do not own, and so I'd like to get it correct first time. The TV has a USB port to allow recording straight to disk, but the manuals don't say how much power can be drawn through the USB port. The manual's instructions state, possibly generically, to plug the drive in before connecting to the TV. Ideally I'd like a small (2.5"?) drive which can draw power over USB, with an mains power input if it turns out the USB port on the TV doesn't offer enough juice. The ideal is to use one cable, two max. A powered USB hub would introduce too much clutter. I've spotted that the LaCie Petit drives have what appears to be an additional power input, but I'm not even sure from the specs what that is. And the device doesn't ship with a mains adapter. Suggestions?

    Read the article

  • NVIDIA Tesla K20C in Dell PowerEdge R720xd --- power cables

    - by CptSupermrkt
    I am trying to put an NVIDIA Tesla K20C into a Dell PowerEdge R720xd. I'm having a bit of trouble understanding the power requirements of the card. First, here is a picture of two pages of the same manual, which seems contradictory to me. One page says only a single connector is required, while the next page says both are required. The entire manual for the card can be found here: http://www.nvidia.com/content/PDF/kepler/Tesla-K20-Active-BD-06499-001-v02.pdf Here is an photo taken of the power connections on the card: And here is a photo of where those connectors need to go, onto the PCI-E riser of the r720xd: Neither the R720xd NOR the GPU came with the necessary cables. And given what appears to be a contradiction in the GPU manual (above), I'm not even sure at this point what we actually need. I have searched high and low online for things like 2x6 pin PCI-E to 8 pin male-to-male and so on, and for the life of me cannot find what we need. In case anyone needs it, the owner's manual of the R720xd can be found here: ftp://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_poweredge/poweredge-r720xd_Owner%27s%20Manual_en-us.pdf The relevant page is page 68, which clearly indicates that the 8-pin female port on the riser card is for a GPU. The bottom line question: exactly what power cables do we need to buy, and where can we find them?

    Read the article

  • how could application installations/configurations be easier in linux?

    - by ajsie
    although you can do anything in linux it tends to require a lot of tweaking in config files and reading a lot of manuals/tutorials before you can have it running in your way. i know that it gets a lot easier by time, and the apt-get installations with ubuntu/debian is heading the right way. but how can linux be more userfriendly for us in the future? i thought that if more is automated like an IDE environment, eg. typing svn will give us all the commands and description about each command when you move between commands with your keyboard. that would be great. but that's just one example. another is the navigation in the terminal between folders. now you have to type a lot just to jump from/to different folders. would be great with some more automatization here too. i know that these extra features will slow down the server, but its 2010 now, and these features are not that heavy for the cpu, but makes it more userfriendly and encourage maintainance of a server, not frighten u off. what do you think about this? should/could we have more user friendly linux environment in servers, something that has annoyed you a lot? a lot of things are done in the unix way, but maybe we should reinvent the wheel in some areas, cause apparently, its so...repeatingly today and difficult to do easy tasks. it should be easier i think..

    Read the article

  • Are there any tests I can run on a network to simulate 100 heavy network users?

    - by marc.gayle
    I will be hosting a Ruby on Rails workshop at a small hotel in the near future, and while they have 'Wifi' everywhere on the property, and the property normally hosts 150 - 300 people, I am not 100% confident that they have hosted 150 tech people that tend to have heavy web surfing habits/needs. Their tech department is also 1 or 2 guys. Are there any automated tests I can download and run from my laptop, on the network, that would simulate 100 'heavy users' on the network at the same time? Their broadband pipe is a 15mbps cable connection. Would that suffice for the general surfing needs of 100 - 150 techies? I know all it takes is 1 or 2 bit torrenters to kill the entire network, but assuming we can at the very least block those ports or encourage the attendees not to file share on the network, would that speed suffice for general surfing needs? What are good resources online that would allow me to quickly get up to speed on the IT related issues, so that I can ask their sysadmins the right questions? Edit: Note that I am fairly technical, so assume I can get up to speed quickly even with technical manuals, etc.

    Read the article

  • Preventing h/w RAID cards from dropping slow JBOD disks

    - by Kevin
    I'm considering buying a used SAS h/w RAID card for externally attaching HDDs to an HP ProLiant I'm setting up. However, I only require RAID functionality on some of the drives. Theoretically it should be simple to JBOD the other drives, but some of them are inexpensive SATA disks and probably cannot have TLER disabled. I'd like to know, prior to actually ordering a RAID card, whether typically RAID cards would still enforce dropping of disks that do not respond within a few seconds, even if the disk is in a JBOD, and whether there is any way to disable this. Ideally it would be nice to be able to select certain SAS ports that will be pass-through, bypassing the RAID engine entirely and just acting as an HBA for those ports. I know I could buy a separate SAS HBA but that seems like a waste of $ and is also impractical as it's a 1U server so space is extremely limited. My question then is whether the functionality I'm looking for (pass-through on certain ports or at least JBOD drives not getting themselves dropped due to slow response) is typical of proper h/w RAID cards such as PERC 5/E etc. I've browsed through the latter's manual but unfortunately, as with most user manuals, it states the obvious and doesn't state the unobvious. Thanks for any info, Kevin

    Read the article

  • Squid reverse proxy array - siblings not communicating with each other

    - by V. Romanov
    I want to set up 2 squid servers to act as reverse proxy and cache for a webserver on our intranet. The load balancing will be done with DNS round robin or just different mappings for different clients. The thing is, I want both servers to try and contact each other to see if they have the object required in cache before contacting the webserver for it (the network that servers the webserver is the bottleneck and I'm trying to eliminate it) Both squids are configured the same, here are the relevant config lines : acl dvr1_cache_it_best_tv_com dstdomain dvr1.cache.it.best-tv.com acl squid1_it_best_tv_com dstdomain squid1.it.best-tv.com acl squid2_it_best_tv_com dstdomain squid2.it.best-tv.com http_access allow dvr1_cache_it_best_tv_com http_access allow squid1_it_best_tv_com http_access allow squid2_it_best_tv_com http_access allow all http_port 8081 accel defaultsite=dvr1.cache.it.best-tv.com cache_peer dvr1.origin.it.best-tv.com parent 80 0 no-query originserver name=Proxy_dvr1_origin_it_best_tv_com cache_peer squid1.it.best-tv.com sibling 8081 3130 weight=10 name=Proxy_Squid1_it_best_tv_com cache_peer squid2.it.best-tv.com sibling 8081 3130 weight=10 name=Proxy_Squid2_it_best_tv_com cache_peer_access Proxy_dvr1_origin_it_best_tv_com allow dvr1_cache_it_best_tv_com cache_peer_access Proxy_squid1_it_best_tv_com allow squid1_it_best_tv_com cache_peer_access Proxy_squid1_it_best_tv_com allow squid2_it_best_tv_com cache_peer_access Proxy_squid1_it_best_tv_com allow dvr1_cache_it_best_tv_com cache_peer_access Proxy_squid2_it_best_tv_com allow squid1_it_best_tv_com cache_peer_access Proxy_squid2_it_best_tv_com allow squid2_it_best_tv_com cache_peer_access Proxy_squid2_it_best_tv_com allow dvr1_cache_it_best_tv_com just to make it clear - dvr1.cache is the alias for the proxy servers. dvr1.origin is the web server. Both servers work, both serve content and cache it and work fine. However, when I clear the cache on one server and then access it, it gets the content from the parent (DVR1_ORIGIN) instead of going to the sibling squid. What did I configure wrong? Or perhaps I don't understand the architecture correctly? I read the squid manuals but as far as I see i did it all by the book and yet it doesn't work right. Any help will be appreciated!

    Read the article

  • IPTABLE & IP-routed netwok solution for HOST net and VM's subnet

    - by Daniel
    I've got ProxmoxVE2.1 ruled KVM node on Debian and bunch of VM's guests machine. That is how my networking looks like: # network interface settings auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 175.219.59.209 gateway 175.219.59.193 netmask 255.255.255.224 post-up echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp And I've got two working subnet solution auto vmbr0 iface vmbr0 inet static address 10.10.0.1 netmask 255.255.0.0 bridge_ports none bridge_stp off bridge_fd 0 post-up ip route add 10.10.0.1/24 dev vmbr0 This way I can reach internet, to resolve outside hosts, update and download everything I need but can't reach one guest VM out of any other VM's inside my network. The second solution allows me to communicate between VM's: auto vmbr1 iface vmbr1 inet static address 10.10.0.1 netmask 255.255.255.0 bridge_ports none bridge_stp off bridge_fd 0 post-up echo 1 > /proc/sys/net/ipv4/ip_forward post-up iptables -t nat -A POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE post-down iptables -t nat -D POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE I can even NAT internal addresses: -t nat -I PREROUTING -p tcp --dport 789 -j DNAT --to-destination 10.10.0.220:345 My inexperienced mind is ready to double VM's net adapters: one for the first solution and another - for second (with slightly different adresses) but I'm pretty sure that it's a dumb way to resolve the problem and everything can be resolved via iptables/ip route rules that I can't create. I've tried a dozen of "wizard manuals" and "howto's" to mix both solution but without success. Looking for an advice (and good reading links for networking begginers).

    Read the article

  • Compare-Object gives false differences

    - by Andy
    I have some problem with Compare-Object. My task is to get difference between two directory snapshots made at different times. First snapshot is taken like this: ls -recurse d:\dir | export-clixml dir-20100129.xml Then, later, I get second snapshot and load both of them: $b = (import-clixml dir-20100130.xml) $a = (import-clixml dir-20100129.xml) Next, I'm trying to compare with Compare-Object, like that: diff $a $b What I get is in some places files that were added to $b since $a, but in some -- files that were in both snapshots, and some files, that were added to $b, are not given in Compare-Object output. Puzzling, but $b.count - $a.count is EXACTLY the same as (diff $a $b).count. Why is that? Ok, Compare-Object has -property param. I try to use that: diff -property fullname $a $b And I get the whole mess of differences: it shows me ALL the files. For example, say $a contains: A\1.txt A\2.txt A\3.txt And $b contains: X\2.mp3 X\3.mp3 X\4.mp3 A\1.txt A\2.txt A\3.txt diff output is something like that: X\2.mp3 => A\1.txt <= X\3.mp3 => A\2.txt <= X\4.mp3 => A\3.txt <= A\1.txt => A\2.txt => A\3.txt => Weird. I think I don't understand something crucial about Compare- Object usage, and manuals are scarce... Please, help me to get the DIFFERENCE between two directory snapshots. Thanks in advance UPDATE: I've saved data as plain strings like that: > import-clixml dir-20100129.xml | % { $_.fullname } | out-file -enc utf8 a.txt And results are the same. Here're excerpts of both snapshots (top 100-something lines, a.txt and b.txt), output of compare-object, and output of UNIX diff (unified). All files are UTF-8: http://dl.dropbox.com/u/2873752/compare-object-problem.zip

    Read the article

  • Add Social Elements to Your Gmail Contacts with Rapportive

    - by Matthew Guay
    Would you like to discover more about your contacts?  Xobni is a great tool for this in Outlook, and thanks to a small plugin for Gmail, you can get similar functionality right from your favorite webmail app. Setup Rapportive on Your Gmail Browse to the Rapportive site (link below), and click install to add it to your browser.  Rapportive currently only supports Firefox and Google Chrome.  In this test, we installed it on Google Chrome.  Notice that Chrome warns Rapportive may access your private data from Gmail, though Rapportive says that they only use this data securely on your computer or their servers. Next time you log into Gmail, open a message to see the new Rapportive sidebar.  Click Log in to get started. Choose if you want to let Rapportive to access your data. Finally, choose whether to stay logged into Rapportive or to log out when you log out of Gmail.   Using Rapportive Now, when you open an email, you should see more information about your contact on the right side of the message where you usually see Google AdSense ads. You may see an avatar, short bio, and links to their social networks.  You can add notes about a contact also, which lets you use Rapportive as a CRM. You may see more information on some contacts.  Here we see a contact that shows recent Tweets and links to several social networks. Take Rapportive Further You can add more features to Rapportive with Raplets, which are small extensions that add more information or CRM functionality.  To add these, click the Rapportive button on the top of Gmail, and select Add Raplets to Rapportive. Find a Raplet you want, and click Add This. A popup will open to give you more information about the Raplet; click the Add button at the bottom if you still want it. And, if you’re wish to close Rapportive without logging out of Gmail, click the Rapportive link in Gmail and select Log out. Conclusion Whether you want to find out more about your contacts or keep track of notes about them, Rapportive is a great way to do this from Gmail.  With tools like this, Gmail gets a bit more powerful and feels more like a desktop application. If you would like this type of functionality in Outlook, check out our article on how to power up Outlook’s search and contacts with Xobni. Add Rapportive to Gmail Similar Articles Productive Geek Tips How to Import Gmail Contacts Into Outlook 2007Enhance Your Gmail Account in ChromeFigure out which Online accounts are selling your email to spammersAdd Social Bookmarking (Digg This!) Links to your Wordpress BlogFix for New Contact Group Button Not Displaying in Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Easily Search Food Recipes With Recipe Chimp Tech Fanboys Field Guide Check these Awesome Chrome Add-ons iFixit Offers Gadget Repair Manuals Online Vista style sidebar for Windows 7 Create Nice Charts With These Web Based Tools

    Read the article

  • It’s the thought that counts…

    - by Tony Davis
    I recently finished editing a book called Tribal SQL, and it was a fantastic experience. It’s a community-sourced book written by first-timers. Fifteen previously unpublished authors contributed one chapter each, with the seemingly simple remit to write about “what makes them passionate about working with SQL Server, something that all SQL Server DBAs and developers really need to know”. Sure, some of the writing skills were a bit rusty as one would expect from busy people, but the ideas and energy were sheer nectar. Any seasoned editor can deal easily with the problem of fixing the output of untrained writers. We can handle with the occasional technical error too, which is why we have technical reviewers. The editor’s real job is to hone the clarity and flow of ideas, making the author’s knowledge and experience accessible to as many others as possible. What the writer needs to bring, on the other hand, is enthusiasm, attention to detail, common sense, and a sense of the person behind the writing. If any of these are missing, no editor can fix it. We can see these essential characteristics in many of the more seasoned and widely-published writers about SQL. To illustrate what I mean by enthusiasm, or passion, take a look at the work of Laerte Junior or Fabiano Amorim. Both authors have English as a second language, but their energy, enthusiasm, sheer immersion in a technology and thirst to know more, drives them, with a little editorial help, to produce articles of far more practical value than one can find in the “manuals”. There’s the attention to detail of the likes of Jonathan Kehayias, or Paul Randal. Read their work and one begins to understand the knowledge coupled with incredible rigor, the willingness to bend and test every piece of advice offered to make sure it’s correct, that marks out the very best technical writing. There’s the common sense of someone like Louis Davidson. All writers, including Louis, like to stretch the grey matter of their readers, but some of the most valuable writing is that which takes a complicated idea, or distils years of experience, and expresses it in a way that sounds like simple common sense. There’s personality and humor. Contrary to what you may have been told, they can and do mix well with technical writing, as long as they don’t become a distraction. Read someone like Rodney Landrum, or Phil Factor, for numerous examples of articles that teach hard technical lessons but also make you smile at least twice along the way. Writing well is not easy and it takes a certain bravery to expose your ideas and knowledge for dissection by others, but it doesn’t mean that writing should be the preserve only of those trained in the art, or best left to the MVPs. I believe that Tribal SQL is testament to the fact that if you have passion for what you do, and really know your topic then, with a little editorial help, you can write, and people will learn from what you have to say. You can read a sample chapter, by Mark Rasmussen, in this issue of Simple-Talk and I hope you’ll consider checking out the book (if you needed any further encouragement, it’s also for a good cause, Computers4Africa). Cheers, Tony  

    Read the article

  • Preview Before You Paste with Live Preview in Office 2010

    - by DigitalGeekery
    Do you often find yourself frustrated that content you just copied and pasted didn’t turn out the way you expected? With the new Live Preview in Office 2010, you can preview how copied content will look when it’s pasted even between Office applications. Not every paste preview option will be available in every circumstance. The available options will be based on the applications being used and what content is copied. Copy your content like normal by right-clicking and selecting Copy, pressing Crtl + C, or selecting Copy from the Home tab. Next, select your location to paste the content. Now you can access the Paste Preview buttons either by selecting the Paste dropdown list from the Home tab…   …Or by right-clicking. As you hover your cursor over each of the Paste Options buttons, you will see a preview of what it will look like if you paste using that option. Click the corresponding button when you find the paste option you like. The “Paste” will paste all the content and formatting as you can see below. Values will paste values only, no formatting.   Formatting will paste only the formatting, no values. Hover over Paste Special to reveal any additional paste options. The process is similar in other Office applications. As you can see in the Word document below, Keep Text Only will paste the text, but not the orange color format from the original text.   Even after you’ve pasted, there is still time to change your mind. After you paste content you’ll see a Paste Option button near your content. If you don’t, you can pull it up by pressing the Ctrl key. Note: This is also available after using Ctrl + V to paste. Click to enable the dropdown and select one of the available options.   Using Live Paste Preview between multiple applications is just as easy. If we preview pasting the content from our Word document into PowerPoint by using the Keep Source Formatting option, we’ll see that the outcome looks awful. Selecting the Use Destination Theme will merge the text into the theme of the PowerPoint document and looks a lot better on our slide.   Live Paste Preview is a nice addition to Office 2010 and is sure to save time spent undoing the unexpected consequences of pasting content. Looking for more Office 2010 tips? Check out some of our other Office 2010 posts like how to create a customized tab on the Office 2010 ribbon, and how to use the streamlined printing features in Office 2010. Similar Articles Productive Geek Tips Edit Microsoft Word 2007 Documents in Print PreviewPreview Documents Without Opening Them In Word 2007How to See Where a TinyUrl Is Really Linking ToHow To Upload Office 2010 Documents to Web Apps Technical PreviewPreview Links and Images in Google Chrome TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Check these Awesome Chrome Add-ons iFixit Offers Gadget Repair Manuals Online Vista style sidebar for Windows 7 Create Nice Charts With These Web Based Tools Track Daily Goals With 42Goals Video Toolbox is a Superb Online Video Editor

    Read the article

  • Monitor and Control Memory Usage in Google Chrome

    - by Asian Angel
    Do you want to know just how much memory Google Chrome and any installed extensions are using at a given moment? With just a few clicks you can see just what is going on under the hood of your browser. How Much Memory are the Extensions Using? Here is our test browser with a new tab and the Extensions Page open, five enabled extensions, and one disabled at the moment. You can access Chrome’s Task Manager using the Page Menu, going to Developer, and selecting Task manager… Or by right clicking on the Tab Bar and selecting Task manager. There is also a keyboard shortcut (Shift + Esc) available for the “keyboard ninjas”. Sitting idle as shown above here are the stats for our test browser. All of the extensions are sitting there eating memory even though some of them are not available/active for use on our new tab and Extensions Page. Not so good… If the default layout is not to your liking then you can easily modify the information that is available by right clicking and adding/removing extra columns as desired. For our example we added Shared Memory & Private Memory. Using the about:memory Page to View Memory Usage Want even more detail? Type about:memory into the Address Bar and press Enter. Note: You can also access this page by clicking on the Stats for nerds Link in the lower left corner of the Task Manager Window. Focusing on the four distinct areas you can see the exact version of Chrome that is currently installed on your system… View the Memory & Virtual Memory statistics for Chrome… Note: If you have other browsers running at the same time you can view statistics for them here too. See a list of the Processes currently running… And the Memory & Virtual Memory statistics for those processes. The Difference with the Extensions Disabled Just for fun we decided to disable all of the extension in our test browser… The Task Manager Window is looking rather empty now but the memory consumption has definitely seen an improvement. Comparing Memory Usage for Two Extensions with Similar Functions For our next step we decided to compare the memory usage for two extensions with similar functionality. This can be helpful if you are wanting to keep memory consumption trimmed down as much as possible when deciding between similar extensions. First up was Speed Dial”(see our review here). The stats for Speed Dial…quite a change from what was shown above (~3,000 – 6,000 K). Next up was Incredible StartPage (see our review here). Surprisingly both were nearly identical in the amount of memory being used. Purging Memory Perhaps you like the idea of being able to “purge” some of that excess memory consumption. With a simple command switch modification to Chrome’s shortcut(s) you can add a Purge Memory Button to the Task Manager Window as shown below.  Notice the amount of memory being consumed at the moment… Note: The tutorial for adding the command switch can be found here. One quick click and there is a noticeable drop in memory consumption. Conclusion We hope that our examples here will prove useful to you in managing the memory consumption in your own Google Chrome installation. If you have a computer with limited resources every little bit definitely helps out. Similar Articles Productive Geek Tips Stupid Geek Tricks: Compare Your Browser’s Memory Usage with Google ChromeMonitor CPU, Memory, and Disk IO In Windows 7 with Taskbar MetersFix for Firefox memory leak on WindowsHow to Purge Memory in Google ChromeHow to Make Google Chrome Your Default Browser TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows iFixit Offers Gadget Repair Manuals Online Vista style sidebar for Windows 7 Create Nice Charts With These Web Based Tools Track Daily Goals With 42Goals Video Toolbox is a Superb Online Video Editor Fun with 47 charts and graphs

    Read the article

  • Improve Playback Using Enhancements in Windows Media Player 12

    - by DigitalGeekery
    Are you looking for ways to improve the playback of your media in Windows Media Player 12? We’ll show you how to do that by using the enhancements in WMP 12. If you are in Library mode, you’ll need to click the icon at the lower right to switch to Now Playing mode. Right-click anywhere in Media Player while in Now Playing mode, select Enhancements, and select any of the available options.   You can switch between the individual enhancements by clicking the right and left buttons at the top left.   Crossfading and Auto Volume Leveling The Auto Volume Leveling setting is just a simple toggle on and off. If your MP3 or WMA files have volume leveling information values.   You can automatically add volume leveling information values to all files you add to your library by switching to Library view, going to Tools > Options, and selecting Add volume leveling information values for new files on the Library tab. Click OK when finished.   Crossfading will gradually decrease the volume of the song that is ending (fade out) and increase volume of the song that is beginning. Click Turn on Crossfading and then click and drag the slider left or right change the amount of overlap between tracks. Graphic Equalizer The graphic equalizer is toggled on and off by clicking Turn on / Turn off at the top left. You can select pre-defined equalizer settings by music genre by clicking the Default list. The radio buttons on the left allow you to move the sliders individually, in a loose group or a tight group. You can always return to the default settings by clicking Reset. Play Speed Settings Choose a pre-defined settings by clicking Slow, Normal, or Fast. Uncheck the Snap slider to common speeds the move the slider right and left to your desired speed. If nothing else, these settings provide a little fun and amusement. Quiet Mode Quiet mode will level out any sharp volume highs and lows within a single track. Simply toggle the setting on or off and select whether you prefer Medium difference or Little difference by selecting one of the radio buttons. SRS WOW effects SRS WOW effects enhance low-frequency and stereo sound performance. Click Turn on to enable the TruBass and WOW Effect sliders. You can also optimize for your speaker type. Click to switch between Regular, Large, and Headphones. Video Settings Video Settings allow you to adjust the Hue, Brightness, Saturation, and Contrast.   You can also adjust the zoom settings by clicking Select video zoom settings.   Dolby Digital Settings Choose between Normal, Night, and Theater settings to adjust the audio for Dolby Digital content. This setting will only effect media with Dolby Digital sound. Looking for more ways to improve your media experience in WMP 12? Check out how to update metadata and cover art and how to share media with other Windows 7 computers on your home network. Similar Articles Productive Geek Tips Fixing When Windows Media Player Library Won’t Let You Add FilesInstall and Use the VLC Media Player on Ubuntu LinuxHow To Rip a Music CD in Windows 7 Media CenterStream Media from Windows 7 to XP with VLC Media PlayerInstalling Windows Media Player Plugin for Firefox TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Check these Awesome Chrome Add-ons iFixit Offers Gadget Repair Manuals Online Vista style sidebar for Windows 7 Create Nice Charts With These Web Based Tools Track Daily Goals With 42Goals Video Toolbox is a Superb Online Video Editor

    Read the article

  • Threading Overview

    - by ACShorten
    One of the major features of the batch framework is the ability to support multi-threading. The multi-threading support allows a site to increase throughput on an individual batch job by splitting the total workload across multiple individual threads. This means each thread has fine level control over a segment of the total data volume at any time. The idea behind the threading is based upon the notion that "many hands make light work". Each thread takes a segment of data in parallel and operates on that smaller set. The object identifier allocation algorithm built into the product randomly assigns keys to help ensure an even distribution of the numbers of records across the threads and to minimize resource and lock contention. The best way to visualize the concept of threading is to use a "pie" analogy. Imagine the total workset for a batch job is a "pie". If you split that pie into equal sized segments, each segment would represent an individual thread. The concept of threading has advantages and disadvantages: Smaller elapsed runtimes - Jobs that are multi-threaded finish earlier than jobs that are single threaded. With smaller amounts of work to do, jobs with threading will finish earlier. Note: The elapsed runtime of the threads is rarely proportional to the number of threads executed. Even though contention is minimized, some contention does exist for resources which can adversely affect runtime. Threads can be managed individually – Each thread can be started individually and can also be restarted individually in case of failure. If you need to rerun thread X then that is the only thread that needs to be resubmitted. Threading can be somewhat dynamic – The number of threads that are run on any instance can be varied as the thread number and thread limit are parameters passed to the job at runtime. They can also be configured using the configuration files outlined in this document and the relevant manuals.Note: Threading is not dynamic after the job has been submitted Failure risk due to data issues with threading is reduced – As mentioned earlier individual threads can be restarted in case of failure. This limits the risk to the total job if there is a data issue with a particular thread or a group of threads. Number of threads is not infinite – As with any resource there is a theoretical limit. While the thread limit can be up to 1000 threads, the number of threads you can physically execute will be limited by the CPU and IO resources available to the job at execution time. Theoretically with the objects identifiers evenly spread across the threads the elapsed runtime for the threads should all be the same. In other words, when executing in multiple threads theoretically all the threads should finish at the same time. Whilst this is possible, it is also possible that individual threads may take longer than other threads for the following reasons: Workloads within the threads are not always the same - Whilst each thread is operating on the roughly the same amounts of objects, the amount of processing for each object is not always the same. For example, an account may have a more complex rate which requires more processing or a meter has a complex amount of configuration to process. If a thread has a higher proportion of objects with complex processing it will take longer than a thread with simple processing. The amount of processing is dependent on the configuration of the individual data for the job. Data may be skewed – Even though the object identifier generation algorithm attempts to spread the object identifiers across threads there are some jobs that use additional factors to select records for processing. If any of those factors exhibit any data skew then certain threads may finish later. For example, if more accounts are allocated to a particular part of a schedule then threads in that schedule may finish later than other threads executed. Threading is important to the success of individual jobs. For more guidelines and techniques for optimizing threading refer to Multi-Threading Guidelines in the Batch Best Practices for Oracle Utilities Application Framework based products (Doc Id: 836362.1) whitepaper available from My Oracle Support

    Read the article

  • SQL Authority News – Secret Tool Box of Successful Bloggers: 52 Tips to Build a High Traffic Top Ranking Blog

    - by Pinal Dave
    When I started this blog, it was meant as a bookmark for myself for helpful tips and tricks.  Gradually, it grew into a blog that others were reading and commenting on.  While SQL and databases are my first love and the reason I started this blog, the side effect was that I discovered I loved writing.  I discovered a secret goal I didn’t even know I wanted – I wanted to become an author.  For a long time, writing this blog satisfied that urge.  Gradually, though, I wanted to see my name in print. 12th Book Over the past few years I have authored and co-authored a number of books – they are all based on my knowledge of SQL Server, and were meant to spread my years of experience into the world, to share what I have learned with my community.  I currently have elevan of these “manuals” available for sale.  As exciting as it was to see my name in print, I still felt that there was more I could do as an author. That is when I realized that I am more than just a SQL expert.  I have been writing this blog now for more than 10 years, and it grew from a personal bookmark to a thriving website with over 2 million views per month.  I thought to myself “I could write a book about how to create a successful blog!”  And that is exactly what I did.  I am extremely excited to share with all of you my new book – “Secret Toolbox of Successful Bloggers.” A Labor of Love This project has been a labor of love for me.  It started out as a series for this blog – I would post one article a week until I felt the topic had been covered.  I found that as I wrote, new topics kept popping up in my mind, and eventually this small blog series grew into a full book.  The blog series was large enough to last a whole year, so I definitely thought that it could be a full book.  Ideas on how to become a successful blogger were so frequent that, I will admit, I feel like there is so much I left out of this book.  I had a lot more to say than I originally thought! I am so excited to be sharing this book with all of you.  I am so passionate about this topic, and I feel like there are so many people who can benefit from this book.  I know that when I started this blog, I did not know what I was doing, and I would have loved a “helping hand” to tell what to do and what not to do.  If this book can act that way to any of my readers, I feel it is a success. Rules of Thumb If you are interested in the topic of becoming a blogger, as you read this book, keep in mind that it is suggestions only.  Blogging is so new to the world that while there are “rules of thumb” about what to do and what not to do, a map of steps (“first, do x, then do y”) is not going to work for every single blogger.  This book is meant to encourage new bloggers to put their content out there in the world, to be brave and create a community like the one I have here at SQL Authority.  I have gained so much from this community, I wanted to give something back, and this book is just one small part. I hope that everyone who reads this books finds at least one helpful tip, and that everyone can experience the joy of blogging.  That is the whole reason I wrote this book, and what I hope everyone takes away from it. Where Can You Get It? You can get the book from following URL: Kindle eBook | Print Book Reference: Pinal Dave (http://blog.SQLAuthority.com)Filed under: About Me, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQLAuthority Author Visit, T SQL

    Read the article

  • When should I use a Process Model versus a Use Case?

    - by Dave Burke
    This Blog entry is a follow on to https://blogs.oracle.com/oum/entry/oum_is_business_process_and and addresses a question I sometimes get asked…..i.e. “when I am gathering requirements on a Project, should I use a Process Modeling approach, or should I use a Use Case approach?” Not surprisingly, the short answer is “it depends”! Let’s take a scenario where you are working on a Sales Force Automation project. We’ll call the process that is being implemented “Lead-to-Order”. I would typically think of this type of project as being “Process Centric”. In other words, the focus will be on orchestrating a series of human and system related tasks that ultimately deliver value to the business in a cost effective way. Put in even simpler terms……implement an automated pre-sales system. For this type of (Process Centric) project, requirements would typically be gathered through a series of Workshops where the focal point will be on creating, or confirming, the Future-State (To-Be) business process. If pre-defined “best-practice” business process models exist, then of course they could and should be used during the Workshops, but even in their absence, the focus of the Workshops will be to define the optimum series of Tasks, their connections, sequence, and dependencies that will ultimately reflect a business process that meets the needs of the business. Now let’s take another scenario. Assume you are working on a Content Management project that involves automating the creation and management of content for User Manuals, Web Sites, Social Media publications etc. Would you call this type of project “Process Centric”?.......well you could, but it might also fall into the category of complex configuration, plus some custom extensions to a standard software application (COTS). For this type of project it would certainly be worth considering using a Use Case approach in order to 1) understand the requirements, and 2) to capture the functional requirements of the custom extensions. At this point you might be asking “why couldn’t I use a Process Modeling approach for my Content Management project?” Well, of course you could, but you just need to think about which approach is the most effective. Start by analyzing the types of Tasks that will eventually be automated by the system, for example: Best Suited To? Task Name Process Model Use Case Notes Manage outbound calls Ö A series of linked human and system tasks for calling and following up with prospects Manage content revision Ö Updating the content on a website Update User Preferences Ö Updating a users display preferences Assign Lead Ö Reviewing a lead, then assigning it to a sales person Convert Lead to Quote Ö Updating the status of a lead, and then converting it to a sales order As you can see, it’s not an exact science, and either approach is viable for the Tasks listed above. However, where you have a series of interconnected Tasks or Activities, than when combined, deliver value to the business, then that would be a good indicator to lead with a Process Modeling approach. On the other hand, when the Tasks or Activities in question are more isolated and/or do not cross traditional departmental boundaries, then a Use Case approach might be worth considering. Now let’s take one final scenario….. As you captured the To-Be Process flows for the Sales Force automation project, you discover a “Gap” in terms of what the client requires, and what the standard COTS application can provide. Let’s assume that the only way forward is to develop a Custom Extension. This would now be a perfect opportunity to document the functional requirements (behind the Gap) using a Use Case approach. After all, we will be developing some new software, and one of the most effective ways to begin the Software Development Lifecycle is to follow a Use Case approach. As always, your comments are most welcome.

    Read the article

  • How to parse amadeus air ticket file

    - by Andrus
    Amadeous produces AIR file like below for every flyight reservation. I need to read reservation number and source and destionation airports from this file. I searched goog for "amadeous air format" but havent found format description. Wikipedia entry about EDIFACt is a bit different, it does not describe this content. Where to fnd information about the file structure ? How to parse this file ? I have not idea about the file stucture, does it contain records like sql table or is it some reservation protocol instructions like postscript file ? Application should work in Microsoft Windows and preferably in Visual FoxPro or C# language. FoxPro or Microsoft Visual Studio 2012 Express can used as programming environment Google returns only Amadeus users guides and tutorials like in comment and in http://www.amadeusschweiz.com/en/documentation/usermanuals.html Those are user manuals. Most promising looks Amadeus Air user guide from this: File which I received name was air.txt and first token in file is AIR-BLK206 Maybe BLK206 is some booking format descriptor. Google returns some documens like my using this so it looks like it is commonly used. This file probably describes how to reserve ticket, which produces air.txt file. I seacrched this and ticket user guide for BLK but those do not contains this abbreviation. Commands in user manual look different than those from this file. How to use this information to extract reservation number and destination airport from this file ? I havent found format description using google. There are amadeus user guides, tutorials ja quick reference files similar which you posted but I do'nt understand how to use them to parse this file. One message describes that this is form of EDIFACT. However EDIFACT message sample in Wikipedia is also diffrerent. I need to create quick prototype to customer which shows that we vcan read those files. Maybe there are some programs which can used to display it in human readable form ?

    Read the article

  • How To Create Your Own x86 Operating System for Modern PC Computers

    - by mudge
    I'd like to create a new operating system for x86 PC computers. I'd like it to be 64-bit but possibly run as 32-bit as well. I have these kinds of questions: What kinds of things do you start working on first? Knowing where to start in writing your own operating system seems to me to be a tricky subject, so I am interested in your input. Generally how to go about making your own 32-bit/64-bit operating system, or good resources that mention useful information about going about writing your own operating system for x86 computers. I don't care how old sources are as long as they are still relevant and useful to what I am doing. I know that I will want it to have kernel drivers that access peripheral hardware directly. Where should I look for advice and documentation for programming and understanding the interface to peripheral hardware the operating system will communicate with? I will need to understand how the operating system will receive input and interact with keyboards, mice, computer monitors, hard drives, USB, etc. etc. This is probably the area I know least about. I have the Intel instruction set manuals and have been getting more familiar with assembly programming, so the CPU side of things is what I know the most about. At this point I'm thinking that I'd like to implement the Linux system calls within my operating system so that programs that run on Linux can run on my operating system. I want my operating system to use the ELF binary format. I wonder what obstacles I have to overcome to achieve this Linux compatibility. Are the main things implementing the system calls that Linux provides, and using the ELF format? What else? I am also interested in people's thoughts about why it might not be a good idea to make your own operating system, and why it is a good idea to make your own operating system. Thank you for any input.

    Read the article

  • How do you keep all your languages straight?

    - by Chris Blackwell
    I think I'm going a little crazy. Right now, I'm working with the following languages (I was just doing a mental inventory): C++ - our game engine Assembler - low level debugging and a few co-processor specific routines Lua - our game engine scripting language HLSL - for shaders Python - our build system and utility tools Objective C/C++ - game engine platform code for Mac and iPhone C# - A few tools developed in our overseas office ExtendScript - Photoshop exporting tools ActionScript - UI scripting VBScript - some spreadsheet related stuff PHP - some web related stuff SQL - some web and tool related stuff On top of this are the plethora of API's that often have many different ways of doing the same thing: std library, boost, .NET, wxWidgets, Cocoa, Carbon, native script libraries for Python, Lua, etc, OpenGL, Direct3d, GDI, Aqua, augh! I find myself inadvertently conflating languages and api's, not realizing what I'm doing until I get syntax errors. I feel like I can't possibly keep up with it, and I can't possibly be proficient in all of these areas. Especially outside the realm of C++ and Python, I find myself programming more by looking at manuals that from memory. Do you have a similar problem? Ideas for compartmentalizing so you're more efficient? Deciding where you want to stay proficient? Organizational tips? Good ways to remember when you switch from Lua to C++ you need to start using semi-colons again? Rants on how complicated we programmers have made things for ourselves? Any ideas welcome!

    Read the article

  • Packaging for Ubuntu - Web Application

    - by Sam
    A web application has no make file unlike C++ or anything like that. However, it needs to be placed into specific directories...e.g /var/www. I'm new to linux packaging, so my question is, how do I package my app into a .deb such that when its being installed, it gets put into something like /etc/myprogram/bundles/myprogram-3.4? Mine in particular is a java app running on apache tomcat. I've managed to create a .deb file by reading painstakingly every word in http://www.debian.org/doc/manuals/maint-guide. However when I follow the instructions I end up getting 1) a .deb file that is 1.7kb instead of the ~240mb that it should be, because apparently it is lacking all my source code. 2) confused because I don't know whether I was supposed to write some sort of makefile. I am not even sure where to go about learning the answer to that question, and then I'd have to deal with how to write a makefile. I've posted a similar question to ubuntuforums, but I feel like I'm more likely to get a response here.

    Read the article

  • how could installations/configurations be easier in linux?

    - by ajsie
    although you can do anything in linux it tends to require a lot of tweaking in config files and reading a lot of manuals/tutorials before you can have it running in your way. i know that it gets a lot easier by time, and the apt-get installations with ubuntu/debian is heading the right way. but how can linux be more userfriendly for us in the future? i thought that if more is automated like an IDE environment, eg. typing svn will give us all the commands and description about each command when you move between commands with your keyboard. that would be great. but that's just one example. another is the navigation in the terminal between folders. now you have to type a lot just to jump from/to different folders. would be great with some more automatization here too. i know that these extra features will slow down the server, but its 2010 now, and these features are not that heavy for the cpu, but makes it more userfriendly and encourage maintainance of a server, not frighten u off. what do you think about this? should/could we have more user friendly linux environment in servers, something that has annoyed you a lot? a lot of things are done in the unix way, but maybe we should reinvent the wheel in some areas, cause apparently, its so...repeatingly today and difficult to do easy tasks. it should be easier i think..

    Read the article

  • I want to merge two PostScript Documents, pagewise. How?

    - by Peter Miehle
    hello, i have a tricky question, so i need to describe my problem: i need to print 2-sided booklets (a third of a paper) on normal paper (german A4, but letter is okay also) and cut the paper afterwards. The Pages are in a Postscript Level 2 File (generated by an ancient printer driver, so no chance to patch that, except ps2ps) generated by me with the ancient OS's Printing driver facilities (GpiMove, GpiLine, GpiText etc). I do not want to throw away two-thirds of the paper, so my idea is: Take file one, two and three, merge them (how?) on new double-sided papers by translate/move file two and three by one resp. two thirds and print the resulting new pages. If it helps, I can manage to print one page of the booklet per file. I cannot "speak" postscript natively, but I am capable of parsing and merging and manipulating files programmaticly. Maybe you can hint me to a webpage. I've read through the manuals on adobe's site and followed the links on www.inkguides.com/postscript.asp Maybe there are techniques with PDF that would help? I can translate ps2pdf. Thanks for help Peter Miehle PS: my current solution: i.e. 8 pages: print page 1, 4 and 7 on page one, 2,5,8 on page two and 3,6,blank on page three, cut the paper and restack. But i want to use a electrical cutting machine, which works better with thicker stacks of paper.

    Read the article

< Previous Page | 2 3 4 5 6 7 8  | Next Page >