Search Results

Search found 725 results on 29 pages for 'slot'.

Page 6/29 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

• Motherboard booting without RAM in Dimm1

  - by Jesus Ramos

  Is it possible to have a motherboard boot without placing RAM in the DIMM1 slot? Our new cooling solutions for motherboards are causing us issues where some boards that have RAM with raised heatsinks will not actually fit because the DIMM1 slot is partially blocked. Currently we mount the RAM in DIMM1 and DIMM3 because it's dual channel, are there any settings that can be changed on the BIOS to allow motherboard to boot without RAM in DIMM1 such as placing the RAM in DIMM2 and DIMM4?

  Read the article

• Cisco 1841: Multi-wan capable?

  - by gravyface

  Have an 1841 router with the following interfaces: 0/0 0/1 AUX on the right side, believe it's slot 1, there's an add-on interface FE0 (shows up as 000). Does this allow a multi-WAN configuration? i.e. can I use 0/1 for WAN1 and FE0 as WAN2 out-of-the-box or does this require additional licensing and/or another add-on interface in slot 0?

  Read the article

• How to set up linux watchdog daemon with Intel 6300esb

  - by ACiD GRiM

  I've been searching for this on Google for sometime now and I have yet to find proper documentation on how to connect the kernel driver for my 6300esb watchdog timer to /dev/watchdog and ensure that watchdog daemon is keeping it alive. I am using RHEL compatible Scientific Linux 6.3 in a KVM virtual machine by the way Below is everything I've tried so far: dmesg|grep 6300 i6300ESB timer: Intel 6300ESB WatchDog Timer Driver v0.04 i6300ESB timer: initialized (0xffffc900008b8000). heartbeat=30 sec (nowayout=0) | ll /dev/watchdog crw-rw----. 1 root root 10, 130 Sep 22 22:25 /dev/watchdog | /etc/watchdog.conf #ping = 172.31.14.1 #ping = 172.26.1.255 #interface = eth0 file = /var/log/messages #change = 1407 # Uncomment to enable test. Setting one of these values to '0' disables it. # These values will hopefully never reboot your machine during normal use # (if your machine is really hung, the loadavg will go much higher than 25) max-load-1 = 24 max-load-5 = 18 max-load-15 = 12 # Note that this is the number of pages! # To get the real size, check how large the pagesize is on your machine. #min-memory = 1 #repair-binary = /usr/sbin/repair #test-binary = #test-timeout = watchdog-device = /dev/watchdog # Defaults compiled into the binary #temperature-device = #max-temperature = 120 # Defaults compiled into the binary #admin = root interval = 10 #logtick = 1 # This greatly decreases the chance that watchdog won't be scheduled before # your machine is really loaded realtime = yes priority = 1 # Check if syslogd is still running by enabling the following line #pidfile = /var/run/syslogd.pid Now maybe I'm not testing it correctly, but I would expecting that stopping the watchdog service would cause the /dev/watchdog to time out after 30 seconds and I should see the host reboot, however this does not happen. Also, here is my config for the KVM vm <!-- WARNING: THIS IS AN AUTO-GENERATED FILE. CHANGES TO IT ARE LIKELY TO BE OVERWRITTEN AND LOST. Changes to this xml configuration should be made using: virsh edit sl6template or other application using the libvirt API. --> <domain type='kvm'> <name>sl6template</name> <uuid>960d0ac2-2e6a-5efa-87a3-6bb779e15b6a</uuid> <memory unit='KiB'>262144</memory> <currentMemory unit='KiB'>262144</currentMemory> <vcpu placement='static'>1</vcpu> <os> <type arch='x86_64' machine='rhel6.3.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <cpu mode='custom' match='exact'> <model fallback='allow'>Westmere</model> <vendor>Intel</vendor> <feature policy='require' name='tm2'/> <feature policy='require' name='est'/> <feature policy='require' name='vmx'/> <feature policy='require' name='ds'/> <feature policy='require' name='smx'/> <feature policy='require' name='ss'/> <feature policy='require' name='vme'/> <feature policy='require' name='dtes64'/> <feature policy='require' name='rdtscp'/> <feature policy='require' name='ht'/> <feature policy='require' name='dca'/> <feature policy='require' name='pbe'/> <feature policy='require' name='tm'/> <feature policy='require' name='pdcm'/> <feature policy='require' name='pdpe1gb'/> <feature policy='require' name='ds_cpl'/> <feature policy='require' name='pclmuldq'/> <feature policy='require' name='xtpr'/> <feature policy='require' name='acpi'/> <feature policy='require' name='monitor'/> <feature policy='require' name='aes'/> </cpu> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/mnt/data/vms/sl6template.img'/> <target dev='vda' bus='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </disk> <controller type='usb' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x2'/> </controller> <interface type='bridge'> <mac address='52:54:00:44:57:f6'/> <source bridge='br0.2'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:88:0f:42'/> <source bridge='br1'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <watchdog model='i6300esb' action='reset'> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </watchdog> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> </domain> Any help is appreciated as the most I've found are patches to kvm and general softdog documentation or IPMI watchdog answers.

  Read the article

• Two Different nVidia Cards, One as Graphics, One as Physics - Possible?

  - by Jasarien

  Hey guys, Soon I will have a brand new Geforce GTX 285 to replace my current 8800GT. Will it be possible to move my 8800GT to another PCIX slot, put the GTX 285 into the primary slot and use the nVidia software to make the 8800GT do physics? I have enough PCIX slots on my motherboard (4). The GTX 285 will take up 2, so the 8800GT should fit in the 3rd. If anyone knows if this is possible, I would be grateful to be educated!

  Read the article

• How to increase acpiphp slots?

  - by Eil

  Hi, Oh RHEL 5.5, there are 31 ACPI PCI hotplug slots by default: acpiphp: Slot [1] registered ... acpiphp: Slot [31] registered Is there a way to increase this number? I haven't been able to find an argument to supply to modprobe, or a sysctl knob to tweak, but I know there must be ways to get more slots based on some Google sleuthing. (For the curious, this is just preliminary experimentation to see how many virtual disks I can hot-add to a running KVM guest.)

  Read the article

• How to increase acpiphp slots?

  - by Eil

  Oh RHEL 5.5, there are 31 ACPI PCI hotplug slots by default: acpiphp: Slot [1] registered ... acpiphp: Slot [31] registered Is there a way to increase this number? I haven't been able to find an argument to supply to modprobe, or a sysctl knob to tweak, but I know there must be ways to get more slots based on some Google sleuthing. (For the curious, this is just preliminary experimentation to see how many virtual disks I can hot-add to a running KVM guest.)

  Read the article

• Issues in Fedora detecting on board NIC card

  - by Vivek27

  Basically I have two NIC cards (on-board + Added in PCI slot) on my Linux machine running Fedora 12.By default the OS detects the NIC card in the PCI slot but it fails to detect the on board network card.Following are few details of the same Linux Vivek 2.6.32.26-175.fc12.i686.PAE #1 SMP Wed Dec 1 21:45:50 UTC 2010 i686 i686 i386 GNU/Linux ifconfig -a doesen't show the on board NIC card.Any thoughts for it please? Since it is also related to network configuration. I posted it here.

  Read the article

• what is the mistake in my code

  - by Solitaire

  class myslot { public: Q_OBJECT myslot() { } ~myslot() { } typedef enum Emycars{volvo,benz,tata}cars; public slots: void hellowslot(myslot::cars); }; void myslot::hellowslot(myslot::cars cars1) { } class mysignal { public: Q_OBJECT public: mysignal(myslot *ourslot) { bool val = QObject::connect(this,SIGNAL(hellowsignal(myslot::Emycars)),ourslot,SLOT(hellowslot(myslot::Emycars))); } ~mysignal() { } signals: void hellowsignal(myslot::Emycars); }; int main(int argc, char *argv[]) { QApplication a(argc, argv); myslot slot; mysignal sig(&slot); // DeleteNow w; // w.showMaximized(); return a.exec(); } what is the mistake in mycode, the way which i have written connect for the function which recive enum is right or not? please let me know where i am wrong.

  Read the article

• What software analogies have helped you?

  - by Galwegian

  I have often enjoyed the use of analogies in understanding a software scenario or problem. For example, to understand the concept of public key encryption, the 'locked mailbox' analogy or similar is often used as an aid: An analogy for public-key encryption is that of a locked mailbox with a mail slot. The mail slot is exposed and accessible to the public; its location (the street address) is in essence the public key. Anyone knowing the street address can go to the door and drop a written message through the slot; however, only the person who possesses the key can open the mailbox and read the message. My question is: What analogies have you used or heard of in your career that have given you that "Eureka" moment with a complex concept? EDIT: If you have a good one, don't just state the name, please share with the group!

  Read the article

• Work time in fullcalendar [Solution]

  - by Zozo

  Full calendar have no included options to work-time feature (selecting first and last rows in agenda view for any day - where in example company is not working). I managed something like that: viewDisplay: function(view){ $.ajax({ url: 'index.php?r=calendar/Default/worktime', dataType: 'json', success: function(data){ if(view.name=='agendaWeek') selectWorkTime(data, 30, 0, 24, false); else if(view.name=='agendaDay') selectDayWorkTime(data, 30, 0, 24, view, false); } }); } Where index.php?r=calendar/Default/worktime is php file returning json. It looks like that: $arr = array( 'mon' => array('8:00', '17:00'), 'tue' => array('9:00', '15:00'), 'wed' => array('9:30', '19:00'), 'thu' => array('6:00', '14:00'), 'fri' => array('0:00', '24:00'), 'sat' => array('9:00', '14:00'), 'sun' => array() ); foreach ($arr as &$day){ foreach($day as &$hour){ $tmp = explode(':', $hour); $hour = $tmp[0] * 3600 + $tmp[1] * 60; } } print json_encode($arr); and at the end, some functions using for counting and selecting work-time: function selectDayWorkTime(timeArray, slotMinutes, minTime, maxTime, viewObject, showAtHolidays){ var dayname; $('.fc-content').find('.fc-view-agendaWeek').find('.fc-agenda-body') .children('.fc-work-time').remove(); $('.fc-content').find('.fc-view-agendaDay') .find('.fc-work-time-day').removeClass('fc-work-time-day'); switch(viewObject.start.getDay()){ case 1: dayname='mon'; break; case 2: dayname='tue'; break; case 3: dayname='wed'; break; case 4: dayname='thu'; break; case 5: dayname='fri'; break; case 6: dayname='sat'; break; case 0: dayname='sun'; break; } for(var day in timeArray){ if(day == dayname){ if($('.fc-content').find('.fc-view-agendaDay').find('.fc-'+day).attr('class').search('fc-holiday') == -1 || showAtHolidays){ var startBefore = 0; var endBefore = timeArray[day][0] / (60 * slotMinutes) - (minTime * 60) / slotMinutes; var startAfter = timeArray[day][1] / (60 * slotMinutes) - (minTime * 60) / slotMinutes; var endAfter = (maxTime - minTime) * 60 / slotMinutes - 1; for(startBefore; startBefore < endBefore; startBefore++){ $('.fc-view-agendaDay').find('.fc-slot'+startBefore).find('div').addClass('fc-work-time-day'); } for(startAfter; startAfter <= endAfter; startAfter++){ $('.fc-view-agendaDay').find('.fc-slot'+startAfter).find('div').addClass('fc-work-time-day'); } } } } } function selectWorkTime(timeArray, slotMinutes, minTime, maxTime, showAtHolidays){ for(var day in timeArray){ var startBefore = 0; var endBefore = timeArray[day][0] / (60 * slotMinutes) - (minTime * 60) / slotMinutes; var startAfter = timeArray[day][1] / (60 * slotMinutes) - (minTime * 60) / slotMinutes; var endAfter = (maxTime - minTime) * 60 / slotMinutes - 1; if(startBefore > endBefore) endBefore = startBefore; if(startAfter > endAfter) startAfter = endAfter; try{ selectCell(startBefore, endBefore, 'fc-'+day, 'fc-work-time', false, showAtHolidays); selectCell(startAfter, endAfter, 'fc-'+day, 'fc-work-time', true, showAtHolidays); } catch(e){ continue; } } } function selectCell(startRowNo, endRowNo, collClass, cellClass, closeGap, showAtHolidays){ $('.fc-content').find('.fc-view-agendaWeek').find('.fc-agenda-body') .children('.'+cellClass+''+startRowNo+''+collClass).remove(); $('.fc-content').find('.fc-view-agendaDay') .find('.fc-work-time-day').removeClass('fc-work-time-day'); if($('.fc-content').find('.fc-view-agendaWeek').find('.'+collClass).attr('class').search('fc-holiday') == -1 || showAtHolidays){ var width = $('.fc-content').find('.fc-view-agendaWeek') .find('.'+collClass+':last').width(); var height = 0; if(closeGap && (startRowNo != endRowNo)){ height = $('.fc-content').find('.fc-view-agendaWeek') .find('.fc-slot'+ startRowNo).height(); } $('.fc-view-agendaWeek').find('.fc-agenda-body').prepend('<div class="'+cellClass+' ' + ''+cellClass+''+startRowNo+''+collClass+'"></div>'); $('.'+cellClass).width(width - 2); height += $('.fc-content').find('.fc-view-agendaWeek') .find('.fc-slot'+ endRowNo).position().top - $('.fc-content').find('.fc-view-agendaWeek') .find('.fc-slot'+ startRowNo).position().top; $('.'+cellClass+''+startRowNo+''+collClass).height(height); $('.'+cellClass+''+startRowNo+''+collClass) .css('margin-top', $('.fc-content').find('.fc-view-agendaWeek') .find('.fc-slot'+ startRowNo).position().top); $('.'+cellClass+''+startRowNo+''+collClass) .css('margin-left', $('.fc-content').find('.fc-view-agendaWeek') .find('.'+collClass+':last').offset().left - width / 2); } } Don't forget about CSS: .fc-work-time-day{ background-color: yellow; opacity: 0.3; filter: alpha(opacity=30); /* for IE */ } .fc-work-time{ position: absolute; background-color: yellow; z-index:10; margin: 0; padding: 0; text-align: left; z-index: 0; opacity: 0.3; filter: alpha(opacity=30); /* for IE */ } So, I've got some questions about - is the other way to make the same, but no using absolute div's in agendaWeek? And... How can I get in viewDisplay function actual slotMinutes, minTime and maxTime

  Read the article

• How to use QMetaMethod with QObject::connect

  - by VestniK

  I have two instances of QObject subclasses and two QMetaMethod instances of signal in one of objects and slot in another object. I want to connect this signal and slot with each other. I've looked through the qobject.h file and find that SIGNAL() and SLOT() macro are just add "1" or "2" character to the beginning of method signature so it looks like it should be possible to add the same character to the beginning of string returned by QMetaMethod::signature() but this approach depends on some undocumented internals of toolkit and may be broken at any time by a new version of Qt. Does anybody know reliable way to connect signals and slots through their QMetaMethod reflection representation?

  Read the article

• How to handle business rules with a REST API?

  - by Ciprio

  I have a REST API to manage a booking system I'm searching how to manage this situation : A customer can book a time slot : A TimeSlot resource is created and linked to a Person resource. In order to create the link between a time lot and a person, the REST client send a POST request on the TimeSlot resource But if too many people booked the same slot (let's say the limit is 5 links), it must be impossible to create more associations. How can I handle this business restriction ? Can I return a 404 status code with a JSON response detailing the error with a status code ? Is it a RESTFul approach ? EDIT : Like suggested below I used status 409 Conflict in addition to a JSON response detailing the error

  Read the article

• 64-bit 13.10 shows 1GB less RAM than 64-bit 13.04 did

  - by kiloseven

  Multiple 64-bit versions (Kubuntu, Lubuntu and Xubuntu) once installed on my ThinkPad R60 show 3GB of RAM, not the correct 4GB of RAM. Last week with 13.04, I had 4GB of RAM (which matches the BIOS) and this week I have 3GB available. Inquiring minds want to know. Details follow: Linux R60 3.11.0-12-generic #19-Ubuntu SMP Wed Oct 9 16:20:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux r60 free -m reports: _ total used free shared buffers cached Mem: 3001 854 2146 0 22 486 -/+ buffers/cache: 346 2655 Swap: 0 0 0 . . . . . . lshw shows: description: Notebook product: 9459AT8 () vendor: LENOVO version: ThinkPad R60/R60i serial: redacted width: 64 bits capabilities: smbios-2.4 dmi-2.4 vsyscall32 configuration: administrator_password=disabled boot=normal chassis=notebook family=ThinkPad R60/R60i frontpanel_password=unknown keyboard_password=disabled power-on_password=disabled uuid=126E4001-48CA-11CB-9D53-B982AE0D1ABB *-core description: Motherboard product: 9459AT8 vendor: LENOVO physical id: 0 version: Not Available *-firmware description: BIOS vendor: LENOVO physical id: 0 version: 7CETC1WW (2.11 ) date: 01/09/2007 size: 144KiB capacity: 1984KiB capabilities: pci pcmcia pnp upgrade shadowing escd cdboot bootselect socketedrom edd acpi usb biosbootspecification {snip} *-memory description: System Memory physical id: 29 slot: System board or motherboard size: 4GiB *-bank:0 description: SODIMM DDR2 Synchronous physical id: 0 slot: DIMM 1 size: 2GiB width: 64 bits *-bank:1 description: SODIMM DDR2 Synchronous physical id: 1 slot: DIMM 2 size: 2GiB width: 64 bits dpkg -l linux-* returns: Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Description +++-======================================-=======================================-========================================================================== un linux-doc-3.2.0 (no description available) ii linux-firmware 1.79.6 Firmware for Linux kernel drivers ii linux-generic 3.2.0.52.62 Complete Generic Linux kernel un linux-headers (no description available) un linux-headers-3 (no description available) un linux-headers-3.0 (no description available) un linux-headers-3.2.0-23 (no description available) un linux-headers-3.2.0-23-generic (no description available) ii linux-headers-3.2.0-52 3.2.0-52.78 Header files related to Linux kernel version 3.2.0 ii linux-headers-3.2.0-52-generic 3.2.0-52.78 Linux kernel headers for version 3.2.0 on 64 bit x86 SMP ii linux-headers-generic 3.2.0.52.62 Generic Linux kernel headers un linux-image (no description available) un linux-image-3.0 (no description available) ii linux-image-3.2.0-52-generic 3.2.0-52.78 Linux kernel image for version 3.2.0 on 64 bit x86 SMP ii linux-image-generic 3.2.0.52.62 Generic Linux kernel image un linux-initramfs-tool (no description available) un linux-kernel-headers (no description available) un linux-kernel-log-daemon (no description available) ii linux-libc-dev 3.2.0-52.78 Linux Kernel Headers for development un linux-restricted-common (no description available) ii linux-sound-base 1.0.25+dfsg-0ubuntu1.1 base package for ALSA and OSS sound systems un linux-source-3.2.0 (no description available) un linux-tools (no description available)

  Read the article

• Using MVP, how to create a view from another view, linked with the same model object

  - by Dinaiz

  Background We use the Model-View-Presenter design pattern along with the abstract factory pattern and the "signal/slot" pattern in our application, to fullfill 2 main requirements Enhance testability (very lightweight GUI, every action can be simulated in unit tests) Make the "view" totally independant from the rest, so we can change the actual view implementation, without changing anything else In order to do so our code is divided in 4 layers : Core : which holds the model Presenter : which manages interactions between the view interfaces (see bellow) and the core View Interfaces : they define the signals and slots for a View, but not the implementation Views : the actual implementation of the views When the presenter creates or deals with views, it uses an abstract factory and only knows about the view interfaces. It does the signal/slot binding between views interfaces. It doesn't care about the actual implementation. In the "views" layer, we have a concrete factory which deals with implementations. The signal/slot mechanism is implemented using a custom framework built upon boost::function. Really, what we have is something like that : http://martinfowler.com/eaaDev/PassiveScreen.html Everything works fine. The problem However, there's a problem I don't know how to solve. Let's take for example a very simple drag and drop example. I have two ContainersViews (ContainerView1, ContainerView2). ContainerView1 has an ItemView1. I drag the ItemView1 from ContainerView1 to ContainerView2. ContainerView2 must create an ItemView2, of a different type, but which "points" to the same model object as ItemView1. So the ContainerView2 gets a callback called for the drop action with ItemView1 as a parameter. It calls ContainerPresenterB passing it ItemViewB In this case we are only dealing with views. In MVP-PV, views aren't supposed to know anything about the presenter nor the model, right ? How can I create the ItemView2 from the ItemView1, not knowing which model object is ItemView1 representing ? I thought about adding an "itemId" to every view, this id being the id of the core object the view represents. So in pseudo code, ContainerPresenter2 would do something like itemView2=abstractWidgetFactory.createItemView2(); this.add(itemView2,itemView1.getCoreObjectId()) I don't get too much into details. That just work. The problem I have here is that those itemIds are just like pointers. And pointers can be dangling. Imagine that by mistake, I delete itemView1, and this deletes coreObject1. The itemView2 will have a coreObjectId which represents an invalid coreObject. Isn't there a more elegant and "bulletproof" solution ? Even though I never did ObjectiveC or macOSX programming, I couldn't help but notice that our framework is very similar to Cocoa framework. How do they deal with this kind of problem ? Couldn't find more in-depth information about that on google. If someone could shed some light on this. I hope this question isn't too confusing ...

  Read the article

• How to run Ubuntu fully in initramfs?

  - by miernik

  I have a machine with 10 GB of RAM, and I would like to run Ubuntu on it (Debian also OK if its easier), fully in RAM in such a way: I boot from a compressed image on an USB flash disk, that is uncompressed into RAM, and then I can remove the disk from the USB slot, and use the system only with RAM, without any permanent disk. Whenever I make any changes that I want permanent, I would put the flash disk back into the USB slot (possibly not the same one as I used initially to boot, as I would like to keep many versions of the boot flash disk), and run some command that would save the current state into a compressed image on the disk. How can I set this up?

  Read the article

• Appropriate level of granularity for component-based architecture

  - by Jon Purdy

  I'm working on a game with a component-based architecture. An Entity owns a set of Component instances, each of which has a set of Slot instances with which to store, send, and receive values. Factory functions such as Player produce entities with the required components and slot connections. I'm trying to determine the best level of granularity for components. For example, right now Position, Velocity, and Acceleration are all separate components, connected in series. Velocity and Acceleration could easily be rewritten into a uniform Delta component, or Position, Velocity, and Acceleration could be combined alongside such components as Friction and Gravity into a monolithic Physics component. Should a component have the smallest responsibility possible (at the cost of lots of interconnectivity) or should related components be combined into monolithic ones (at the cost of flexibility)? I'm leaning toward the former, but I could use a second opinion.

  Read the article

• KVM Virtual guest Paused on Reboot

  - by David Hamilton

  I'm running REHL 6 and just installed a Ubuntu Server Guest via KVM set to start at boot. This works correctly and the guest loads, but it loads "paused" and requires that I manually un-pause it. Can someone give me a hint as to how I can I get the Guest OS to actually become active on boot? Here is the libvert dump as requested...Also tried libvert auto-start --- no effect. <domain type='kvm' id='1'> <name>MailServer</name> <uuid>a61dae75-1f5c-d536-718f-3c615d9b4868</uuid> <memory>4194304</memory> <currentMemory>4194304</currentMemory> <vcpu>4</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/home/MailServer/MailServer-1.img'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <alias name='ide0-1-0'/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:cd:f9:9f'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes'/> <sound model='ac97'> <alias name='sound0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='selinux'> <label>system_u:system_r:svirt_t:s0:c211,c271</label> <imagelabel>system_u:object_r:svirt_image_t:s0:c211,c271</imagelabel> </seclabel></domain>

  Read the article

• Is this Ubuntu One DBus signal connection code correct?

  - by Chris Wilson

  This is my first time using DBus so I'm not entirely sure if I'm going about this the right way. I'm attempting to connect the the Ubuntu One DBus service and obtain login credentials for my app, however the slots I've connected to the DBus return signals detailed here never seem to be firing, despite a positive result being returned during the connection. Before I start looking for errors in the details relating to this specific service, could someone please tell me if this code would even work in the first place, or if I'm done something wrong here? int main() { UbuntuOneDBus *u1Dbus = new UbuntuOneDBus; if( u1Dbus->init() ){ qDebug() << "Message queued"; } } UbuntuOneDBus::UbuntuOneDBus() { service = "com.ubuntuone.Credentials"; path = "/credentials"; interface = "com.ubuntuone.CredentialsManagement"; method = "register"; signature = "a{ss} (Dict of {String, String})"; connectReturnSignals(); } bool UbuntuOneDBus::init() { QDBusMessage message = QDBusMessage::createMethodCall( service, path, interface, method ); bool queued = QDBusConnection::sessionBus().send( message ); return queued; } void UbuntuOneDBus::connectReturnSignals() { bool connectionSuccessful = false; connectionSuccessful = QDBusConnection::sessionBus().connect( service, path, interface, "CredentialsFound", "a{ss} (Dict of {String, String})", this, SLOT( credentialsFound() ) ); if( ! connectionSuccessful ) qDebug() << "Connection to DBus::CredentialsFound signal failed"; connectionSuccessful = QDBusConnection::systemBus().connect( service, path, interface, "CredentialsNotFound", "(nothing)", this, SLOT( credentialsNotFound() ) ); if( ! connectionSuccessful ) qDebug() << "Connection to DBus::CredentialsNotFound signal failed"; connectionSuccessful = QDBusConnection::systemBus().connect( service, path, interface, "CredentialsError", "a{ss} (Dict of {String, String})", this, SLOT( credential if( ! connectionSuccessful ) qDebug() << "Connection to DBus::CredentialsError signal failed"; } void UbuntuOneDBus::credentialsFound() { std::cout << "Credentials found" << std::endl; } void UbuntuOneDBus::credentialsNotFound() { std::cout << "Credentials not found" << std::endl; } void UbuntuOneDBus::credentialsError() { std::cout << "Credentials error" << std::endl; }

  Read the article

• In 10.10, USB 3.0 PCI Express card recognized by lspci but not lsusb or dmesg. How to fix?

  - by Paul

  Asus N PC, runs 10.10 x86_64 The Asus N comes with 4 usb 2.0 ports, each labelled 2.0 on the case. Attempting to add two usb 3.0 ports to be provided by a generic usb 3.0 pci express card installed in the pci expres slot. The new card says usb 3.0 and has the blue ports. The card is installed into the laptop unpowered, then the laptop is powered on and boots normally. Nothing happens when a USB 3.0 flash drive is inserted into the usb 3.0 port. uname -a Linux drpaulbrewer-N90SV 2.6.35.8 #1 SMP Fri Jan 14 15:54:11 EST 2011 x86_64 GNU/Linux lspci -v 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64 Kernel modules: sis-agp 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fa000000-fdefffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [f4] Power Management version 2 Capabilities: [70] Subsystem: Silicon Integrated Systems [SiS] PCI-to-PCI bridge Kernel driver in use: pcieport 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] (rev 01) Flags: bus master, medium devsel, latency 0 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01) (prog-if 80 [Master]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 128 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at ffe0 [size=16] Capabilities: [58] Power Management version 2 Kernel driver in use: pata_sis 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 20 Memory at f9fff000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 21 Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 22 Memory at f9ffd000 (32-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter (rev 02) Subsystem: ASUSTeK Computer Inc. Device 11f5 Flags: bus master, medium devsel, latency 0, IRQ 19 Memory at f9ffcc00 (32-bit, non-prefetchable) [size=128] I/O ports at cc00 [size=128] Capabilities: [40] Power Management version 2 Kernel driver in use: sis190 Kernel modules: sis190 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mode (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 17 I/O ports at c800 [size=8] I/O ports at c400 [size=4] I/O ports at c000 [size=8] I/O ports at bc00 [size=4] I/O ports at b800 [size=16] I/O ports at b400 [size=128] Capabilities: [58] Power Management version 2 Kernel driver in use: sata_sis Kernel modules: sata_sis 00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: fdf00000-fdffffff Capabilities: [b0] Subsystem: Silicon Integrated Systems [SiS] Device 0004 Capabilities: [c0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [f4] Power Management version 2 Kernel driver in use: pcieport 00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=06, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fe000000-febfffff Prefetchable memory behind bridge: 00000000f6000000-00000000f8ffffff Capabilities: [b0] Subsystem: Silicon Integrated Systems [SiS] Device 0004 Capabilities: [c0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [f4] Power Management version 2 Kernel driver in use: pcieport 00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio Controller Subsystem: ASUSTeK Computer Inc. Device 17b3 Flags: bus master, medium devsel, latency 0, IRQ 18 Memory at f9ff4000 (32-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 01:00.0 VGA compatible controller: nVidia Corporation G96 [GeForce GT 130M] (rev a1) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 2021 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fc000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=256M] Memory at fa000000 (64-bit, non-prefetchable) [size=32M] I/O ports at dc00 [size=128] [virtual] Expansion ROM at fde80000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Kernel driver in use: nvidia Kernel modules: nvidia-current, nouveau, nvidiafb 02:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Device 1a3b:1067 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fdff0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Kernel driver in use: ath9k Kernel modules: ath9k 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at febfe000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable- Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 lsusb Bus 003 Device 002: ID 0b05:1751 ASUSTek Computer, Inc. BT-253 Bluetooth Adapter Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 001 Device 002: ID 04f2:b071 Chicony Electronics Co., Ltd 2.0M UVC Webcam / CNF7129 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub dmesg trying to post dmesg exceeded the stackexchange posting limit of 30K... but nothing there is usb 3.0

  Read the article

• Tracking first visit date in Google Analytics

  - by dusan

  I want track a site's visitor retention using Google Analytics, to see if unregistered users are returning to it, within a time frame of 2+ months from now. This blog post seems to be on the right track, but I want to track unregistered users, so I don't have a "join date" or similar variable at my disposal. This other blog post suggests using all 5 GA custom variables, using the first variable slot on the first week, variable 2 on week 2, etc. This method will allow me to track 5 weeks of visitors. I want to track more than 5 weeks of visitors, so I was thinking on using two custom variables in GA: visitor's first visit date, and visitor's last visit date. How I can save the first visit date? Because if I save another value in the same slot the old value will be overwritten, and I don't know how reliable is to save that variable conditionally (reading the __utmv cookie to check whether the "first visit date" is set, if it isn't set I save the current date)

  Read the article

• How to suppress "Card not present / present" spam in syslog?

  - by vava

  I'm getting a lot of Dec 27 08:35:49 htpc kernel: [ 1552.153797] pciehp 0000:00:1c.5:pcie04: Card not present on Slot(0-2) Dec 27 08:35:49 htpc kernel: [ 1552.157744] pciehp 0000:00:1c.5:pcie04: Card present on Slot(0-2) messages in my syslog, about 10 every second. That just makes syslog unusable, can I somehow get rid of them? I don't know and don't really care about the reason of those messages being there, partly because my motherboard doesn't have pcie slots on it and partly because everything I care about works perfectly. That might be a WiFi chip I disabled in bios but hey, I don't want wifi to be powered on, I'm not using it. So can I just suppress those messages?

  Read the article

• Is there a way to suppress one specific message from syslog?

  - by vava

  I'm getting a lot of Dec 27 08:35:49 htpc kernel: [ 1552.153797] pciehp 0000:00:1c.5:pcie04: Card not present on Slot(0-2) Dec 27 08:35:49 htpc kernel: [ 1552.157744] pciehp 0000:00:1c.5:pcie04: Card present on Slot(0-2) messages in my syslog, about 10 every second. That just makes syslog unusable, can I somehow get rid of them? I don't know and don't really care about the reason of those messages being there, partly because my motherboard doesn't have pcie slots on it and partly because everything I care about works perfectly. That might be a WiFi chip I disabled in bios but hey, I don't want wifi to be powered on, I'm not using it. So can I just suppress those messages?

  Read the article

• JET now available on OTN

  - by mramcha

  I know some of you have been waiting patiently, so I'm pleased to announce that the JET bundle is now available for download on the Oracle Technology Network. I've migrated most of the content from the old Sun wiki site, and got the download in a single handy location on OTN. Download JET now.  The version available is the current latest, which is 4.9.4. This version contains a number of updates, the most significant of which is the ability to specify slot locations instead of the traditional cXtYdZsN nomenclature. This is pretty useful when trying to Jumpstart multiple servers with SAS2.0 based HBAs, as they will have the WWN embedded in the cXtYdZsN name, and it's pretty difficult to guess what that will be until you've booted the server. The JetSDS and JetZFS modules have also been updated to use the slot terminology. Happy JETing,

  Read the article

• Qwt plot not working , simple plot curve not appeat

  - by user1629213

  I followed the example of simple plot in qwt examples to plot a curve. The axis and the graph appear in the Qt main window user interface but the curve not. I assigned values to fit the curve but the curve not appear. Any suggestions and help how to solve the problem? Here is my code MainWindow::MainWindow( int argc, char** argv, QWidget *parent ) : QMainWindow( parent ) , qnode( argc,argv ) { ui.setupUi( this ); // Calling this incidentally connects all ui's triggers to on_...() callbacks in this class. QObject::connect( ui.actionAbout_Qt, SIGNAL( triggered( bool )), qApp, SLOT( aboutQt( ))); // qApp is a global variable for the application ReadSettings( ); setWindowIcon( QIcon( ":/images/icon.png" )); ui.tab_manager->setCurrentIndex( 0 ); // ensure the first tab is showing - qt-designer should have this already hardwired, but often loses it (settings?). QObject::connect( &qnode, SIGNAL( rosShutdown( )), this, SLOT( close( ))); /********************* ** Logging **********************/ ui.view_logging->setModel( qnode.loggingModel( )); QObject::connect( &qnode, SIGNAL( loggingUpdated( )), this, SLOT( updateLoggingView( ))); QObject::connect( &qnode, SIGNAL( graphReceived( )), this, SLOT( onGraphReceived( ))); QObject::connect( &qnode, SIGNAL( parameterReceived( )), this, SLOT( onParameterReceived( ))); /********************* ** Auto Start **********************/ if ( ui.checkbox_remember_settings->isChecked( )) { on_button_connect_clicked( true ); } ui.parameters->setAttribute( Qt::WA_NoMousePropagation ); ui.parameters->setAttribute( Qt::WA_OpaquePaintEvent ); ui.plotgraph->setAttribute( Qt::WA_NoMousePropagation ); ui.plotgraph->setAttribute( Qt::WA_OpaquePaintEvent ); p_plot = new QwtPlot(ui.plotgraph); p_plot->setTitle( "Plot LinVel" ); p_plot->setCanvasBackground( Qt::white ); // Axis p_plot->setAxisTitle( QwtPlot::xBottom, "Time(sec)" ); p_plot->setAxisTitle( QwtPlot::yLeft, "Linear Velocity (m/sec)" ); p_plot->setAxisScale( QwtPlot::yLeft, 0.0, 10.0 ); p_plot->setAxisScale( QwtPlot::xBottom, 0.0, 50.0 ); p_plot->insertLegend( new QwtLegend() ); //samplingThread.start(); QwtPlotGrid *grid = new QwtPlotGrid(); grid->attach( p_plot ); curve = new QwtPlotCurve(); curve->setTitle( "Linear velocity" ); // Set curve styles curve->setPen( Qt::blue, 4 ), curve->setRenderHint( QwtPlotItem::RenderAntialiased, true ); QwtSymbol *symbol = new QwtSymbol( QwtSymbol::Ellipse, QBrush( Qt::yellow), QPen( Qt::red, 2 ), QSize( 8, 8 ) ); curve->setSymbol( symbol); // Assign values to the curve //curve->setSamples(ui.plotgraph.get_linv_g());//yaw_g,trav_g,wall_g; curve->attach( p_plot ); p_plot->resize( 600, 400 ); p_plot->show(); void MainWindow::onGraphReceived( ) { { QMutexLocker locker( &qnode.m_mutex ); } } void MainWindow::onParameterReceived( ) { { QMutexLocker locker( &qnode.m_mutex ); std::vector<double> p_ = qnode.get_parameters(); std::cout << p_[0]<<" "<<p_[1]<<" "<<p_[2]<<" "<<p_[3]<<" "<<p_[4] << std::endl; } } Any help?

  Read the article

• Is it possible to shrink the size of an HP Smart Array logical drive?

  - by ewwhite

  I know extension is quite possible using the hpacucli utility, but is there an easy way to reduce the size of an existing logical drive (not array)? The controller is a P410i in a ProLiant DL360 G6 server. I'd like to reduce logicaldrive 1 from 72GB to 40GB. => ctrl all show config detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: 5001438006FD9A50 Cache Serial Number: PAAVP9VYFB8Y RAID 6 (ADG) Status: Disabled Controller Status: OK Chassis Slot: Hardware Revision: Rev C Firmware Version: 3.66 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 3 secs Surface Scan Mode: Idle Queue Depth: Automatic Monitor and Performance Delay: 60 min Elevator Sort: Enabled Degraded Performance Optimization: Disabled Inconsistency Repair Policy: Disabled Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 15 secs Cache Board Present: True Cache Status: OK Accelerator Ratio: 25% Read / 75% Write Drive Write Cache: Enabled Total Cache Size: 512 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 412476 MB Status: OK Logical Drive: 1 Size: 72.0 GB Fault Tolerance: RAID 1+0 Heads: 255 Sectors Per Track: 32 Cylinders: 18504 Strip Size: 256 KB Status: OK Array Accelerator: Enabled Unique Identifier: 600508B1001C132E4BBDFAA6DAD13DA3 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 196 MB, / 12.0 GB, /usr 8.0 GB, /var 4.0 GB, /tmp 2.0 GB OS Status: LOCKED Logical Drive Label: AE438D6A5001438006FD9A50BE0A Mirror Group 0: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 146 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 146 GB, OK) SEP (Vendor ID PMCSIERA, Model SRC 8x6G) 250 Device Number: 250 Firmware Version: RevC WWID: 5001438006FD9A5F Vendor ID: PMCSIERA Model: SRC 8x6G

  Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >