Search Results

Search found 22380 results on 896 pages for 'hard drive failure'.

Page 60/896 | < Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >

  • raid advice with SSD and two HDD

    - by Nin
    I have a new machine with one 128GB SSD and two 1TB HDD. On the SSD is the OS and my initial thought was to put the two HDD in RAID 1 for user data. After some more thought I came up with two other setups and now I'm in doubt :) Can someone advise what would be the best setup? 1: single SSD and HDD in RAID 1 (original thought) 2: Create 2 partitions on the HDD (128GB and 872GB). Put the two 872GB in RAID 1 and create another RAID 1 with the SSD and one 128GB HDD partition. 3: Create 2 partitions on the HDD (750/250), put the 705GB in RAID 1 and use the 2 250GB as backup and make automatic snapshots of the SSD to (one of) these partitions. I think the 2 main questions are: Is it advisable to create a raid array with only part of a drive and actively use the other part of that drive or should you always use the full disk? Is it advisable to create a raid 1 array with a SSD and HDD or will that blow the whole speed advantage of the SSD?

    Read the article

  • No wubildr, No spaceleft, Boot Error and A previous installation was detected in D:\ubuntu. Please uninstall that before continuing

    - by tdc2bdc
    At first I was downloading Ubuntu 12.10 using Windows Installer, but I cancelled it after just 2-3 minutes and dowloaded 32-Bit ISO (ubuntu-12.10-desktop-i386). Then I created bootable USB Stick (new HP 210 v210 w) using Pendrivelinux (Universal-USB-Installer-1.9.1.4). I Formatted D Drive. (Both by Windows & EaseUS) I've set boot priority correctly. But after getting message "Boot Error", I ran wubi.exe directly from USB drive. Now the message is "A previous installation was detected in D:\ubuntu. Please uninstall that before continuing." I formatted D: again and performed disk check, surface test using EaseUS. It shows no error or bad sectors. Formatted & checked my pendrive too. Directly ran .iso. But same error keeps coming. I found way around above problems, by copying extracted .iso on D:\ and installing Ubuntu using wubi.exe and though on boot it was shown with Windows 7, selecting it caused following error Try hd(0,0): NTFS5 : No wubildr Try hd(0,1): NTFS5 : So, I uninstalled it and Reeinstalled it Now installation fails at around 7mins saying " An error occurred. No space left on device. For more info please see log file " My D: is a 9 GB partition. (99% Free) Ubuntu Site 12.10 says it needs around 4.5 GB. Now Trying it by extendin D: to 10 GB... Got No wubildr. Please help. tdc2bdc

    Read the article

  • How do I remove a USB drive's write protection?

    - by nate
    I have a SanDisk Cruser Blade USB stick that suddenly seems to be write protected. I tried running DiskPart but after I write the command "attributes disk clear readonly" it displays this: Microsoft DiskPart version 5.1.3565 ADD - Add a mirror to a simple volume. ACTIVE - Marks the current basic partition as an active boot partition. ASSIGN - Assign a drive letter or mount point to the selected volume. BREAK - Break a mirror set. CLEAN - Clear the configuration information, or all information, off the disk. CONVERT - Converts between different disk formats. CREATE - Create a volume or partition. DELETE - Delete an object. DETAIL - Provide details about an object. EXIT - Exit DiskPart EXTEND - Extend a volume. HELP - Prints a list of commands. IMPORT - Imports a disk group. LIST - Prints out a list of objects. INACTIVE - Marks the current basic partition as an inactive partition. ONLINE - Online a disk that is currently marked as offline. REM - Does nothing. Used to comment scripts. REMOVE - Remove a drive letter or mount point assignment. REPAIR - Repair a RAID-5 volume. RESCAN - Rescan the computer looking for disks and volumes. RETAIN - Place a retainer partition under a simple volume. SELECT - Move the focus to an object. It's like when you type help at the DiskPart prompt, so how do I get past this? This problem started when I plugged the stick into a laptop which had viruses, if that's any help.

    Read the article

  • Upon USB insert, record unique identifer sting, format drive to FAT32 and copy a file. Bash or Pytho

    - by samsixty
    Hello, This is what I want to do, insert USB flash drive. mount it. record uniquie identifer string to a file. format the drive to FAT32. copy a text file to the drive. unmount it. remove the drive. 30 times The situation is this, I have bought 30 usb drives. I need to format each one to ensure they are clean, I need the unique string from each device. I need to put the same txt file on each one. I am not great at writing scripts but can read and follow bash and python. Any pointers would be appreciated.

    Read the article

  • OpenSSL: certificate signature failure error

    - by e-t172
    I'm trying to wget La Banque Postale's website. $ wget https://www.labanquepostale.fr/ --2009-10-08 17:25:03-- https://www.labanquepostale.fr/ Resolving www.labanquepostale.fr... 81.252.54.6 Connecting to www.labanquepostale.fr|81.252.54.6|:443... connected. ERROR: cannot verify www.labanquepostale.fr's certificate, issued by `/C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=Terms of use at https://www.verisign.com/rpa (c)06/CN=VeriSign Class 3 Extended Validation SSL SGC CA': certificate signature failure To connect to www.labanquepostale.fr insecurely, use `--no-check-certificate'. Unable to establish SSL connection. I'm using Debian Sid. On another machine which is running Debian Sid with same software versions the command works perfectly. ca-certificates is installed on both machines (I tried removing it and reinstalling it in case a certificate got corrupted somehow, no luck). Opening https://www.labanquepostale.fr/ in Iceweasel on the same machine works perfectly. Additional information: $ openssl s_client -CApath /etc/ssl/certs -connect www.labanquepostale.fr:443 CONNECTED(00000003) depth=3 /C=US/O=VeriSign, Inc./OU=Class 3 Public Primary Certification Authority verify error:num=7:certificate signature failure verify return:0 --- Certificate chain 0 s:/1.3.6.1.4.1.311.60.2.1.3=FR/2.5.4.15=V1.0, Clause 5.(b)/serialNumber=421100645/C=FR/postalCode=75006/ST=PARIS/L=PARIS/streetAddress=115 RUE DE SEVRES/O=LA BANQUE POSTALE/OU=DISF2/CN=www.labanquepostale.fr i:/C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=Terms of use at https://www.verisign.com/rpa (c)06/CN=VeriSign Class 3 Extended Validation SSL SGC CA 1 s:/C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=Terms of use at https://www.verisign.com/rpa (c)06/CN=VeriSign Class 3 Extended Validation SSL SGC CA i:/C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=(c) 2006 VeriSign, Inc. - For authorized use only/CN=VeriSign Class 3 Public Primary Certification Authority - G5 2 s:/C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=(c) 2006 VeriSign, Inc. - For authorized use only/CN=VeriSign Class 3 Public Primary Certification Authority - G5 i:/C=US/O=VeriSign, Inc./OU=Class 3 Public Primary Certification Authority 3 s:/C=US/O=VeriSign, Inc./OU=Class 3 Public Primary Certification Authority i:/C=US/O=VeriSign, Inc./OU=Class 3 Public Primary Certification Authority --- Server certificate -----BEGIN CERTIFICATE----- <base64-encoded certificate removed for lisibility> -----END CERTIFICATE----- subject=/1.3.6.1.4.1.311.60.2.1.3=FR/2.5.4.15=V1.0, Clause 5.(b)/serialNumber=421100645 /C=FR/postalCode=75006/ST=PARIS/L=PARIS/streetAddress=115 RUE DE SEVRES/O=LA BANQUE POSTALE/OU=DISF2/CN=www.labanquepostale.fr issuer=/C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=Terms of use at https://www.verisign.com/rpa (c)06/CN=VeriSign Class 3 Extended Validation SSL SGC CA --- No client certificate CA names sent --- SSL handshake has read 5101 bytes and written 300 bytes --- New, TLSv1/SSLv3, Cipher is RC4-MD5 Server public key is 1024 bit Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : RC4-MD5 Session-ID: 0009008CB3ADA9A37CE45B464E989C82AD0793D7585858584ACE056700035363 Session-ID-ctx: Master-Key: 1FB7DAD98B6738BEA7A3B8791B9645334F9C760837D95E3403C108058A3A477683AE74D603152F6E4BFEB6ACA48BC2C3 Key-Arg : None Start Time: 1255015783 Timeout : 300 (sec) Verify return code: 7 (certificate signature failure) --- Any idea why I get certificate signature failure? As if this wasn't strange enough, copy-pasting the "server certificate" mentionned in the output and running openssl verify on it returns OK...

    Read the article

  • How can I detect upload success/failure in a scripted command-line SFTP session

    - by pkpk
    how can I detect success/failure sftp Batch script on Windows OS? I use %errorlevel% to detect success/failure, sometime the %errorlevel% be returned by 0, but that session is fail and the file is not upload to the server. my script is below how can I detect sftp uploaded correctly? THX so much @echo off (echo cd %4 echo put %2 echo exit)>sftpScript.txt sftp -b sftpScript.txt %3 set result=%errorlevel% if result EQU 0 ( del sftpScript.txt del %2 ) else ( del sftpScript.txt ) exit %result%

    Read the article

  • protecting an application against hardware failure [on hold]

    - by alex
    I have an application for which I am looking for a way to protect against hardware and software (operating system ) failure. Cluster seems OK but the storage become the single point of failure and also I do not have a SAN. Can you please tell me if there are other ways to protect the application? Periodically this application is updated and changes should be replicated automatically to the second server.

    Read the article

  • Is it Hard to Write a Blog?

    - by Joe Mayo
    Responding to a tweet I received, asking if I found it hard to write a blog and keep it interesting. This is one of the situations where a 140 character response doesn’t do a question justice. There’s a lot to think about between the subjects of writing, subject matter, and entertainment.  Here’s my take on each of these three topics: There’s all types of writing you can do with various degrees of difficulty. If you’re writing a book and you have a gazillion editors bleeding over your every utterance, then the task becomes harder because you’re second-guessing yourself, not knowing whose opinion will be violated. However, if you’re communicating in a public forum, not too many people care about the grammar as much as whether what you have to say is correct.  For a blog, I would say it’s somewhere in-between.  Right now, I’m using Windows Live Writer, which gives me a few advantages to just typing into the blog editor, such as spelling correction and the ability to save my work and resume later.  Overall, writing is one of those things that you just need to get used to.  It’s an essential skill for developers because you need to document your work, depending on what your definition of proper documentation is, and communicate with other developers via various communications mediums. Not begin good (or not thinking that you’re good) shouldn’t hold you back.  Like most things in life, practice will improve your skill.  So, push away that inner voice that keeps you from moving forward and just do it. A good grasp on the subject matter you’re writing about helps.  However, don’t let a lack of knowledge stop you from writing about something. I recall reading something a while back by a developer who didn’t know a technology but wrote about their experience in learning it. They ended up learning more by expressing their thoughts in writing. If you look around out many blogs today, there are many items written by developers learning what they’re writing about.  So, whether you are sure or unsure, you can still write – just be honest with yourself and your readers about what you’re writing. Also, don’t be afraid to have a different opinion or worry if someone will disagree.  I’ll freely admit that it took a while for me to become accustomed to being criticized. Take the good with the bad and use the bad to make yourself better. Guaranteed, someone will disagree with one or more parts of what I’ve written here or think they have a better approach. No problem, more power to them, and whatever constructive comments they have will be a benefit to me in the future; Otherwise, to h*ll with them. :)  Every time you get knocked down, get right back up, dust the dirt off your backside, and keep moving forward.  You’ll learn in time how to align a subject with your own presentation of the material. Entertainment could be hard or could be natural, depending on the personality of yourself and your target audience. It’s even more challenging because you can say something you think is funny and someone will be offended. In fact, there are a lot of things that you shouldn’t say in the name of a joke, but I won’t mention any of them here for want of not offending anyone. Of course, I probably offended someone by saying that and there is probably an organization somewhere in the world out to get me now. I’m probably not the best person to be giving you advice on entertaining an audience.  I mean, every time I try to tell a joke on Twitter 10 people unfriend me. Okay, maybe 15, but you get my point. One thing you might be interested in knowing is that it’s not too hard for one technical person to entertain other technical people, especially when the subject is of interest.  It’s the excitement in each sentence and passion in each paragraph that will keep another developer entertained and interested in what you have to say. Not everyone will like what you’ve written, but the important part is to find your own voice and it’s likely that there is one person in some corner of the world that likes what you have to say, even if it’s your mom and she doesn’t understand a single word you write. :)   If I could leave you with one final thought; Just do it and don’t let anyone or anything hold you back.   Joe

    Read the article

  • Journaled filesystems and power failure

    - by Yoga
    I heard that even a journaled filesystems such as EXT3/EXT4 might corrupted during power failure, e.g. from wikipedia [1]: In the event of a system crash or power failure, such file systems are quicker to bring back online and less likely to become corrupted. Can anyone provide more detail by giving examples such that when corruption can occur corruption is avoided by journaled filesystems [1] http://en.wikipedia.org/wiki/Journaling_file_system

    Read the article

  • How do I mount my External HDD with filesystem type errors?

    - by Snuggie
    I am a relatively new Ubuntu user and I am having some difficulty mounting my external 2TB HDD. When I first installed Linux my external HDD was working just fine, however, it has stopped working and I have a lot of important files on there that I need. Before my HDD would automatically mount and no worries. Now, however, it doesn't automatically mount and when I try to manually mount it I keep running into filesystem type errors that I can't seem to get past. Below are images that depict my step by step process of how I am trying to mount my HDD along with the errors I am receiving. If anybody has any idea what I am doing wrong or how to correct the issue I would greatly appreciate it. Step 1) Ensure the computer recognizes my external HDD. pj@PJ:~$ dmesg ... [ 5790.367910] scsi 7:0:0:0: Direct-Access WD My Passport 0748 1022 PQ: 0 ANSI: 6 [ 5790.368278] scsi 7:0:0:1: Enclosure WD SES Device 1022 PQ: 0 ANSI: 6 [ 5790.370122] sd 7:0:0:0: Attached scsi generic sg2 type 0 [ 5790.370310] ses 7:0:0:1: Attached Enclosure device [ 5790.370462] ses 7:0:0:1: Attached scsi generic sg3 type 13 [ 5792.971601] sd 7:0:0:0: [sdb] 3906963456 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 5792.972148] sd 7:0:0:0: [sdb] Write Protect is off [ 5792.972162] sd 7:0:0:0: [sdb] Mode Sense: 47 00 10 08 [ 5792.972591] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.972605] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.975235] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.975249] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.987504] sdb: sdb1 [ 5792.988900] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.988911] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.988920] sd 7:0:0:0: [sdb] Attached SCSI disk Step 2) Check if it mounted properly (it does not) pj@PJ:~$ df -ah Filesystem Size Used Avail Use% Mounted on /dev/sda1 682G 3.9G 644G 1% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys none 0 0 0 - /sys/fs/fuse/connections none 0 0 0 - /sys/kernel/debug none 0 0 0 - /sys/kernel/security udev 2.9G 4.0K 2.9G 1% /dev devpts 0 0 0 - /dev/pts tmpfs 1.2G 928K 1.2G 1% /run none 5.0M 0 5.0M 0% /run/lock none 2.9G 156K 2.9G 1% /run/shm gvfs-fuse-daemon 0 0 0 - /home/pj/.gvfs Step 3) Try mounting manually using NTFS and VFAT (both as SDB and SDB1) pj@PJ:~$ sudo mount /dev/sdb /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount /dev/sdb1 /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t ntfs /dev/sdb /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t vfat /dev/sdb /media/Passport/ mount: wrong fs type, bad option, bad superblock on /dev/sdb, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so pj@PJ:~$ sudo mount -t ntfs /dev/sdb1 /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t vfat /dev/sdb1 /media/Passport/ mount: wrong fs type, bad option, bad superblock on /dev/sdb1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so

    Read the article

  • New 3TB HDD, can see full 2.7TB in Linux and Windows, but shows up as 801.6GB in BIOS

    - by Ben Lee
    I recently purchased a Seagate Barracuda 3TB drive (ST3000DM001). After installing it, my BIOS recognized it but reported the size as 801.6gb. I went ahead and booted into Linux anyway (Ubuntu 11.10 64-bit). Linux saw it as a 2.7TB. Following some online instructions (don't have the link handy, unfortunately), it looks liked converting this drive to GPT was recommended. So I used gparted to do that, then formatted it to NTFS also using gparted. (I'm using NTFS because my machine is daul-boot and I want to have access to the drive in Windows too). I rebooted to Windows (Windows 7 64-bit), and Windows also sees the drive with 2.7TB free. Everything seems to be working fine. The only issue is that my BIOS is still reporting the drive as 801.6GB. My motherboard is an ASRock 770 Extreme3 and BIOS is the latest version. Since everything seems to be working with the new drive anyway, I'm hoping that the fact that the BIOS is reporting the wrong size is not an actual problem. But honestly, I don't really know. Anyone out there more familiar with this know if this could potentially cause any problems in the future? Any way to get the BIOS to report the correct size?

    Read the article

  • SATA HDD stuttering on reads (LED on)

    - by jdehaan
    I hope I can get some new ideas to solve the issue. What I have: AMD Phenom II X4 905e Box, Sockel AM3 Gigabyte GA-MA790XTA-UD4, AMD 790X, AM3 ATX WD Caviar GreenPower 1,5TB SATA II 4GB Kit OCZ DDR3 PC3-10666 Platinum Low-Voltage CL7 HIS HD 4670 iSilence4 DDR3 1024MB Native HDMI Dual-DVI, PCI-Express Behavior: Everything works normally excepting the HDD accesses. The drive seems to get stuck in reading data (LED drive by Mainboard is on for a while) then recovers and goes on. There is a delay of more than 30s sometimes. Often it is a matter of 5-10s. This does not seem related to the workload of the disk. What I tried so far: Use different SATA port: I switched from the SATA3 to SATA2 then the SATA driven by the CPU, no difference. Turned AHCI off, drove the SATA in IDE mode, same behavior, now I felt like the HDD has problems Deactivated energy saving settings (BeQuiet, ...), disabled 3 CPUs (msconfig) supposing some race condition or trouble with changing freqs, same trouble With Windows7 Professional 64Bit, I installed the hotfix http://support.microsoft.com/?scid=kb%3Ben-us%3B976418&x=8&y=9 with no success. The problem description matches what I experienced, so I felt lucky but was quite in a sad mood after being deceived. Burned the DLG 5.04f DataLifeGuard CD from WD to check the drive. All tests passed, to my surprise! Installed an Ubuntu on the same drive i386 flavour. Drive still in IDE mode, exactly the same behavior. So the OS does not matter. What I did not try yet: http://www.gigabyte.eu/Support/Motherboard/BIOS_Model.aspx?ProductID=3263 I have a F2 BIOS and there is a F3a Beta, did someone have similar issues that were solved by this update? It is a beta so I fear upgrading a bit and I could find no release notes at all on the net, not really serious work maybe they had issues translating from Chinese??? Using another HDD drive Does someone have other hints or a similar issue? Maybe it is neither the HDD nor the Mainboard/BIOS?

    Read the article

  • My Boot order changed. Why?

    - by Chris
    I have a laptop running Windows XP SP3 with one internal hard drive partitioned into C: (system), D: (storage) and I have an external hard drive, F: (external drive). Yesterday the machine was running fine. Today, I go back to it and see that it's just showing a blinking cursor. Checked through the BIOS and the hard drive checked out fine. CTRL-ALT-DELETED the machine a few times, but I was never able to boot back into the operating system. I threw in a live CD and found out that the boot order of the drives has changed. The external drive is now C:, the system partiton is D:, and the storage partition is E:. Does anyone have any idea of how or why this would have occured? Auto system updates are turned off so there should have been no automatic reboot of the system overnight, and anti-virius runs on the machine and has found no infections before this occured. Edit When I was looking through the BIOS of the machine, I did see that the boot order was changed. But still the same question remains, what would have caused this to happen? I can't believe that a random reboot happened and totally changed my hard drive setup.

    Read the article

  • hp proliant dl360 disk diagnostic issue

    - by user1039384
    We recently got two used drives (15000) and installed on our HP proliant dl360 G5 server. Created RAID1 and used HP SmartStart CD to perform diagnostics. Interestingly, the Diagnostic tab immidiately fails on Logical drive testing saying the Disk1 should be replaced, while the Test tab successfully runs all the complete tests on both disks and does not find any issue. At the meantime, when booting to esxi 5, vSphere periodically shows the Disk1 as Unknown and Logical drive in recovery process. This happens every 5-10 minutes. Here is the log from HP SmartScan diagnostic: 1 - Device, Test: Logical Drive 1, Storage Controller in Slot 0 1 - Description: The controller has reported a critical error in the drive error log. 1 - Recommended Repair: This drive should be replaced. 1 - Failed Count: 44 1 - Error code: F157 There is also another error log record (see below): 2 - Device, Test: test_components/libstorage.so ID 2 - Description: An unexpected exception occurred while performing an operation. Exception message: CISS_StatusHandler::evaluate: commandStatus = 4 (INVALID); hexdump of CISS_ErrorInfo: 00000000: __ __ 04 __ 20 __ __ __ __ __ __ __ __ __ __ __ .... ... ........ 00000010: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ 00000020: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ Device: Hard Drive 2, Storage Controller in Slot 0 Property name: Bad Target Count 2 - Recommended Repair: Reboot or restart Insight Diagnostics. Retry the test. If the problem persists, upgrade to the latest version of Insight Diagnostics. 2 - Failed Count: 48 2 - Error Code: F62 Note that rebooting didn't help and I was running the latest diagnostic software version. Anyone has a clue? Is this a real disk issue? BTW, the controller is Smart Array E200i Thanks in advance

    Read the article

  • Recover hard disk from Raw format

    - by user1632736
    I have been all over the web today with no results. So my drive was encrypted (truecrypt) the whole drive where windows resided. I decided to partition it to install W8 and forgot it was encrypted. So the drive got damaged and not accessible. When connected to a computer it asks for formatting. Somehow I enabled the drive through TrueCrypt on another computer and I could see and get all the files. Then I decided to decrypt the drive thinking that everything would be back to normal. After decryption my drive is not NTFS it is in RAW format. I am trying every possible way to recover, and I am desperate enough to ask lol. I tried: ddrescue (linux) (not mountable, no signature, ntfsfix no good) testdisk (linux and windows) Sees the partitions but cant do anything Many recovery applications. etc etc. I read in different places that doing a quickformat to NTFS and then doing a data recovery might help. I would definitely like a second opinion. Any suggestion would be really helpful

    Read the article

  • Hyper-V and attaching physical disks

    - by Mike Christiansen
    So, I'm looking at rebuilding my home server. My current setup is the following Windows 7 Ultimate 1TB Boot Drive (my smallest drive) Windows Dynamic Spanned volume, continaing 1x 1TB drive, 2x 2TB drives, totalling 5TB. I am upgrading to a hardware RAID controller, and I would like to run Hyper-V server core. However, I want to retain the ability to join my "file server" to a homegroup, so I must use Windows 7. I know VHDs can only be like 127GB or something, so I obviously need to directly connect disks to my Windows 7 machine. Here is my plan: Server Core 2008 R2 (Hyper-V) 1TB Boot Drive (storing VHDs for boot drives of VMs) - possibly in a RAID 1 with my other 1TB drive 5x 2TB drives (1x 2TB drive hot spare), totalling 10TB, directly attached to a Windows 7 VM, for use of homegroup for this array. In the past, I directly attached the windows dynamic volume to a Windows 7 VM, and performance was abysmal. The question is, with hardware RAID, will it really make that much of a difference? Server specs: Intel Core 2 Quad Q9550 2.83GHz Asus Maximus II Formula (PCI-E x16) 8GB DDR2 RAM PC2-6400 (Yes, I know its a bit out of date)

    Read the article

  • Hyper-V and attaching physical disks [migrated]

    - by Mike Christiansen
    So, I'm looking at rebuilding my home server. My current setup is the following Windows 7 Ultimate 1TB Boot Drive (my smallest drive) Windows Dynamic Spanned volume, continaing 1x 1TB drive, 2x 2TB drives, totalling 5TB. I am upgrading to a hardware RAID controller, and I would like to run Hyper-V server core. However, I want to retain the ability to join my "file server" to a homegroup, so I must use Windows 7. I know VHDs can only be like 127GB or something, so I obviously need to directly connect disks to my Windows 7 machine. Here is my plan: Server Core 2008 R2 (Hyper-V) 1TB Boot Drive (storing VHDs for boot drives of VMs) - possibly in a RAID 1 with my other 1TB drive 5x 2TB drives (1x 2TB drive hot spare), totalling 10TB, directly attached to a Windows 7 VM, for use of homegroup for this array. In the past, I directly attached the windows dynamic volume to a Windows 7 VM, and performance was abysmal. The question is, with hardware RAID, will it really make that much of a difference? Server specs: Intel Core 2 Quad Q9550 2.83GHz Asus Maximus II Formula (PCI-E x16) 8GB DDR2 RAM PC2-6400 (Yes, I know its a bit out of date)

    Read the article

  • Windows Vista freezes

    - by Kakurady
    Windows Vista (32-bit) would randomly freeze on my computer, usually 15-30 minutes after login but can happen just after login. All applications would stop responding and the hard drive will not make any sound, and after a while, the mouse cursor will also stop moving. I dual-boot Ubuntu, and that still works fine. It started with the computer freezing when loading Team Fortress 2. Alt-Tab and Ctrl-Alt-Del have no effect, and the hard drive does not make any sound. I tried to verify the game data using Steam and that freezes the computer too. So I stupidly reinstalled the game. Now the game doesn't freeze when it starts, but instead the whole computer randomly freezes. This computer is a Dell XPS M1530 with a 320GB (298GiB) drive (WDC WD3200BEVT-7) split 5-ways, with Windows and Linux a partition each, one more for Linux swap space, and another two partitions for Dell diagnostic program and factory image and drivers. There was once where the hard drive would make clicking noises all day, and only stopped when I rebooted the computer. Since then, the BIOS diagnostics would fail the drive (for "self-test log contains previous errors") whenever ran. (The on-disk diagnostics cannot be run because I overwrote the MBR with GRUB.) Naturally, I thought the hard drive could be the problem. CHKDSK found one bad sector, but this seems to have no effect. System File Checker found two protected files with wrong hashes, one is some kind of IE manifest, and the other is a tcpmon.ini. Neither of them can be restored because their back up copy also have wrong hashes. Nothing about system failures in the event viewer. What should I do next?

    Read the article

  • Raspberry Pi how to format HDD

    - by Speed
    Hi I am very new to Raspberry Pi environment, so looking for a bit of help to format a usb hard disk drive. I ran lsblk and got sda 8:0 0 37.3G 0 disk sda1 8:1 0 37.3G 0 part looking on web, if tried the following "sudo mkfs.ext4 /dev/sda1 -L USB40gb" it did something but when I tried to mount the drive again, it still showed the files that were there before and I can not create new file/folder "Error creating directory: Permission denied" I am writing this from my windows 8.1 pc so can not cut and paste from the pi. trying to format its output is a bit hard. Oh, there is Nothing written after the word "part" above. There use to be /media/USB40gb so I have done something because this has disappeared. I am using PCManFM 0.9.10 It does not have a format option, which would make life a lot easier, but then its not windows. I think I am running the basic linux os for the pi. It boots to a graphic environment, but I do not know how to advise what it is. I think its OpenBox 2.0.4 Thanks in advance Speed PS: I reran the format string above but this time I changed the label to read USB37gb. I did this to confirm that I was in fact formatting the right drive. Low and behold, it actually formatted the drive, wiping everything from it. Great ... testing it by creating a new folder on the drive and get error msg Permission Denied! So I have fixed the formatting issue by trial and error but still can't use the drive... Suggestions anyone?

    Read the article

  • IIS7 Failure after installing Advanced Logging

    - by Guy Harwood
    I came across a nasty issue when i installed the Advanced Logging feature for IIS7 via the Web Platform Installer on my Windows 2008 Server.  Basically, after installation and reboot none of my sites were working and returned 503 – Internal Server Error. Snooping around in the Event Viewer i found the following error reported by the W3SVC… The Module DLL C:\Program Files\IIS\Advanced Logging\AdvancedLoggingModule.dll failed to load. The data is the error Even though the DLLs are there, it is not picking them up. I managed to find a fix via google that involves editing the configapplicationHost.config file in the C:\Windows\System32\inetsrv\ directory. 1.  Copy AdvancedLoggingModule.dll and ClientLoggingHandler.dll to %windir%\system32 (C:\windows\system32  on a default setup) 2.  Locate the file C:\Windows\System32\inetsrv\configapplicationHost.config and make a backup, then open it in a text editor (i recommend Notepad++). 3.  Search for the following 2 lines (mine are located on line 570).. <add name="ClientLoggingHandler" image="%ProgramFiles%\IIS\Advanced Logging\ClientLoggingHandler.dll" /> <add name="AdvancedLoggingModule" image="%ProgramFiles%\IIS\Advanced Logging\AdvancedLoggingModule.dll" /> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } and alter them to…. <add name="ClientLoggingHandler" image="%windir%\system32\ClientLoggingHandler.dll" /> <add name="AdvancedLoggingModule" image="%windir%\system32\AdvancedLoggingModule.dll" /> 4. Open a command prompt and run iisReset. 5. All sites should now be working. .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }

    Read the article

  • Moonlight's Olympic-sized failure

    <b>ZDNet Australia: </b>"Every couple of years, Microsoft and its partners get to show off what the technology is capable of and push the limits of live video coverage. This year, the plethora of Canadian channels covering the Olympics were all available live from one website, and the experience was terrific."

    Read the article

  • TrueCrypt drive letter not available

    - by Tono Nam
    With c# or a batch file I mount a trueCrypt volume located at A:\volumeTrueCrypt.tc With c# I do: static void Main(string[] args) { var p = Process.Start( fileName:@"C:\Program Files\TrueCrypt\TrueCrypt.exe", arguments:@"/v a:\volumetruecrypt.tc /lw /a /p truecrypt" ); p.WaitForExit(); } the alternative is to run the command on the command line as: C:\Windows\system32>"C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /lw /a /p truecrypt Either way I get the error: Why do I get that error? I was able to run that command the first time. The moment I dismounted the volume and tryied to mount it again I got that error. I know that drive letter W is available because it shows as an available letter on true crypt if I where to open it manually: If I where then click on the button mount and then type the password truecrypt (truecrypt is the password) then it will successfully mount on drive w. Why I am not able to mount it from the command line!? If I change the drive letter on the command line it works. I want to use the drive W though. In other words executing "C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /lz /a /p truecrypt will successfully mount that volume on drive z but I do not want to mount it on drive z I want to mount it on drive w. The first time I ran the batch it ran fine. Also if I restart my computer I believe it should work. More info on how to use trueCrypt through the command line can be found at: http://www.truecrypt.org/docs/?s=command-line-usage Edit I was also investivating when does this error occures. In order to generate this error you need to follow this steps. 1) execute the command: (note the /q argument at the end for quiet) "C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /ln /a /p truecrypt /q "C...TrueCrypt.exe" = location where trueCrypt is located /v "path" = location where volume is located /n = drive letter n /p truecrypt = password is "trueCrypt" /q = execute in quiet mode. do not show window note I am mounting to drive letter n 2) now volume should be mounted. 3) Open trueCrypt and manually dismount that volume (without using command line) 4) Attempt to run the same command line (without the /q so you see the error) "C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /ln /a /p truecrypt 5) an error should show up So the problem ocures when I manually dismount the volume. If I dismount it from the command line I get no errors. But I think this is a bug from trueCrypt

    Read the article

  • User based BitLocker Drive Encryption

    - by Starx
    While Unlocking a Encrypted Drive.. It is possible for that drive to be unlocked for only the particular user and not all other users who use the system. For example, there are two users... User1 and User2, user1 unlocked a encrypted drive, now he locks the desktop and user2 comes and open the system from his account. Now, user2 also can access the drive which user1 unlocked. User2 must not be able to open the drive. If he has the password the the drive then he might have access but not before that.

    Read the article

< Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >