Search Results

Search found 2448 results on 98 pages for 'vmware vcenter'.

Page 60/98 | < Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >

  • How do you passthrough native SATA drives to a guest on ESXi?

    - by John
    I have ESXi 4.0 running on an Intel DX58S0 Mothboardboard with an Intel Core i7 930 processor. VT-d is also enabled. I have three drives in the system, drive 0 is used for ESXi. Drive 1 and 2 contain data from an older machine and show up under the "Storage Adapters" section in configuration. I would like to allow a guest machine to access the data on these drives (as nativly as possible). I have enabled passthrough of the motherboard's built in SATA controller (Intel/Marvell 88SE6121 ). This controller shows up in my guest OS, but the guest shows no drives aside from the normal virtual drive. I have tried a Linux guest and Windows7. I have also configured the host machine to try IDE/RAID/ACHI modes for the SATA controller. Any ideas how I can configure one of my guests to get at the raw data on these drives?

    Read the article

  • Extending ext4 partition on debian7.0 on vsphere

    - by VoidPointer
    I have allocated thin provisioning of 15GB when i found 8GB as insufficient. Now debian guest is not able to recognize the change of size. root@debian7-x64:~# lvdisplay --- Logical volume --- LV Path /dev/debian7-x64/root LV Name root VG Name debian7-x64 LV UUID EU6mg0-XTXC-ci3D-bQJi-7XN6-r8Hp-SYxcj0 LV Write Access read/write LV Creation host, time debian7-x64, 2013-06-25 12:02:49 +0530 LV Status available # open 1 LV Size 7.39 GiB Current LE 1892 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 254:0 --- Logical volume --- LV Path /dev/debian7-x64/swap_1 LV Name swap_1 VG Name debian7-x64 LV UUID xDNtoz-tJUq-M5D6-GGCN-gzcD-fwUv-fYYDR1 LV Write Access read/write LV Creation host, time debian7-x64, 2013-06-25 12:02:49 +0530 LV Status available # open 2 LV Size 376.00 MiB Current LE 94 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 254:1 root@debian7-x64:~# pvdisplay --- Physical volume --- PV Name /dev/sda5 VG Name debian7-x64 PV Size 7.76 GiB / not usable 2.00 MiB Allocatable yes (but full) PE Size 4.00 MiB Total PE 1986 Free PE 0 Allocated PE 1986 PV UUID SehkzH-Gq8Y-jI2f-27Tb-uv1Z-tR1R-5OnTxR root@debian7-x64:~# sfdisk -s /dev/sda: 15728640 /dev/mapper/debian7--x64-root: 7749632 /dev/mapper/debian7--x64-swap_1: 385024 total: 23863296 blocks Help me to extend this partition. No problem in rebooting. I dont have any live CD. Environment : debian 7, with lvm, on vsphere, ext4 partition. Can provide more details when needed.

    Read the article

  • Are there any benefits to using a Distributed vSwitch for iSCSI?

    - by dunxd
    I am designing our vSphere farm - we'll be migrating from ESX 3.5 to 4.1. I plan to set up a new farm using ESXi 4.1, and move the Virtual Machines on the 3.5 farm into it by shutdown, then import. In ESX 3.5 there is no distributed networking, so each host has a vSwitch connected to my SAN NICs, and a port group for the vmkernel. In vSphere (ESXi 4.1) I have the extra option to set up a distributed vSwitch and distributed port groups for vmkernel to access iSCSI storage. Is there any benefit to this, or should I stick to non-distributed networking for iSCSI.

    Read the article

  • When copying VM filesystem over netcat, dd copies double the disk size

    - by JivanAmara
    I'm attempting to copy the disk of a working headless virtualbox VM (VM1) on one server to a new VM (VM2) on a vCloud server. I don't have access to the host of VM2. The OS is Windows Server 2003 (32-bit) I start both VMs with a live Knoppix image. I run 'nc -l | dd of=/dev/sda bs=512' on VM2 I run 'dd if=/dev/sda bs=512 | nc ' on VM1 I previously did this with another windows VM and it worked fine. VM1 has a disk of size ~70GB (verified with fdisk); however, the amount of data dd reports read/written is ~139GB. Of course the target machine doesn't work properly. I get a Windows splash screen, then blue error screen with general 'system not working' information. I'm at a loss what could cause this. Any ideas?

    Read the article

  • nmap reports host up when it isn't

    - by martianway
    On an Ubuntu VM I ran: sudo nmap -sP 192.168.0.* This returned: Starting Nmap 5.00 ( http://nmap.org ) at 2010-12-28 22:46 PST Host 192.168.0.0 is up (0.00064s latency). Host 192.168.0.1 is up (0.00078s latency). Host 192.168.0.2 is up (0.00011s latency). . . . Host 192.168.0.254 is up (0.00068s latency). Host 192.168.0.255 is up (0.00066s latency). The problem is I only have 4 live machines on 192.168.0.* so why did nmap report every ip in the subnet has a live host? The ip address of the Ubuntu machine is 192.168.28.131 From this VM I can ping the live systems on my internal subnet 192.168.0.* and get the expected response. And if I ping a machine that doesn't exist I can get no response as expected.

    Read the article

  • VM clients can not access WAN

    - by Saariko
    I have a new VM host on my network, on a Dell R620. The dedicated iDrac is connected with static IP of: 192.168.3.x NIC #1 is connected to my router The eSXI 5.1 host is with IP of 192.168.3.250 The vSphere appliance has a static IP of 192.168.3.241 All the clients on the new host are in the same network 192.168.3.x All clients are Windows 2008 R2 My problem is that non of the clients can access the WAN. I can't ping anything which is beyond my router. I CAN ping anything within my router, even if it's on a different subnet - 192.168.0.x (Router rules are in tact and working) I can ping the gateway (192.168.3.254) One thing that I checked, and is bothering my (but don't know if it has any relevance) is that on the Host Networking properties, there is a vmnic0 (picture) that shows as if it only recognizes 192.168.0.x network - is that so? The command: route print shows me the following details, where I have a duplicate entry for 0.0.0.0 (and one is wrong) - which is probably also why it's not working

    Read the article

  • Problems with USB-Devices using VDR

    - by emmsinator
    Hey Guys, I'm using VDR on vSphere4. It works sucessfully. I've already backuped several VMs with VDR and I like it very much. But now we got a problem. We have 2 VMs, using an USB-Device Server with a stick plugged in, which is definetely need by these 2 VMs for Licensing and so. Every time, I start the Backup process, the VMs lost the communication to the USB-Server and its stick after building the snapshot and while online. Because of that, the software on these VMs can't work correctly. I have to restart both Machines to solve this problem. These fact is bad for an automatic backup. Does VDR have a special function for those cases or is something like this already known? It would be no problem, to shutdown the servers for building snapshots on Saturday or Sunday. Can VDR initiate a shutdown before starting the backup process? Otherwise I must try to use scripts, but that wouldn't be so nice. Thanks a lot for your help.

    Read the article

  • Virtual MS Sql Server not consuming enough CPU

    - by rocketman
    We have a Win2008 server 32 bit running as a virtual machine under ESX server. It has 6 CPU cores of 2Gz each and 4GB ram. It's running MS Sql Server 2008 R2 only. Problem: The server is heavily loaded and responds slowly. From windows taskmanagers point of view, it really looks overloaded, CPU wise. However, our external "cloud manager" says it's only using 2.5GHz worth of CPU-cycles in the cluster. I/O times looks "good". We have already tried to set the SQL servers number of working threads from 0(auto) to 256, to no effect. How to tune the VM host, guest or SQL to use all of it's alotted resources? Does it sound possible att all?

    Read the article

  • Cannot resize an ntfs (Windows Server 2k3r2) boot partition booting from gparted

    - by jshin47
    I am trying to use gparted to make my ntfs system/boot partition larger. I expanded the disk in ESX, providing an extra 60 GB or so of free space. I confirmed that this free space is available in gparted: However, when I try to go to "Move/Resize" the boot partition, there is no unallocated space for me to allocate. It will let me resize the "extended" (non-boot) partition, which makes me think the issue is that the partitions are not contiguous. If it's not obvious, I am no expert in partitioning/storage so any help is appreciated.

    Read the article

  • ESXi 4 failed to find boot device

    - by phil
    I had exsi 3.5 running just fine, the upgrade to 4 failed ( i thought it would so everything is backed up ). but it did boot just could not import the data store So i did a fresh install of ESXi 4. Now it says failed to find boot device. Not sure why. i have wiped the disk, the controller is a adaptec 3405, it worked fine in 3.5 and when i upgrade to 4 it did boot. Now it just hangs at loading vfat. then the failed to find boot device. Any ideas?

    Read the article

  • arp "who-has tell" on cloned machine

    - by mcmorry
    I have a urgent problem to solve today, but I'm lost. Please help. I've cloned a Virtual Machine hosted on VM Ware ESXi 4.1 The OS is now Ubuntu Server 12.04 LTS, but at the time of cloning it was 10.04 LTS. I fixed the MAC address manually inside /etc/udev/rules.d/70-persistent-net.rules. It is a known problem on Ubuntu. I had to remove the old MAC address and set the new one as eth0. Everything seems to work fine, except ARP. My provider OVH sent me a warning to resolve it today (this is the second day) or they will block my IP! The log contains many lines like this: Tue Jun 5 01:04:29 2012 : arp who-has 178.32.136.212 tell 178.32.136.224 where .224 is the cloned server that is causing problems, and .212 is the cloned one. arp -na returns: ? (178.33.230.254) at 00:07:b4:00:00:02 [ether] on eth0 ? (178.32.136.212) at 00:50:56:09:8e:f1 [ether] on eth0 The first IP is the ESXi machine. The second one should not be there. I'm not an expert and I don't know what else to do to fix this problem. Any help will be very appreciated. Thanks. EDIT: ifcofig on .224: eth0 Link encap:Ethernet HWaddr 00:50:56:01:32:c6 inet addr:178.32.136.224 Bcast:178.32.136.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fe01:32c6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:399924 errors:0 dropped:465 overruns:0 frame:0 TX packets:241884 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:58006071 (58.0 MB) TX bytes:663603166 (663.6 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:516216 errors:0 dropped:0 overruns:0 frame:0 TX packets:516216 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:236284275 (236.2 MB) TX bytes:236284275 (236.2 MB) ifconfig on .212: eth0 Link encap:Ethernet HWaddr 00:50:56:09:8e:f1 inet addr:178.32.136.212 Bcast:178.32.136.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fe09:8ef1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16014 errors:0 dropped:0 overruns:0 frame:0 TX packets:14511 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15134444 (15.1 MB) TX bytes:2683025 (2.6 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9944 errors:0 dropped:0 overruns:0 frame:0 TX packets:9944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1139347 (1.1 MB) TX bytes:1139347 (1.1 MB)

    Read the article

  • VM using a secondary graphic card

    - by Arthur
    Hi everyone, at the moment i have a dual monitor setup on my main PCIe gfx card. I know that on windows it is almost impossible to have a second card (eg no thrills PCI card) running without having an SLI motherboard because of a driver issue. Well this was my conclusion after many weeks of research. I was thinking...is it possible to use a VM in order to utilize the secondary card as the default video output to feed another monitor? let me know if you want me to clarify Thanks :)

    Read the article

  • Capacity Planner errors

    - by Gabrie
    Hi Performing a discovery at customer site and although systems do get discovered, I get a lot (100000+) of these errors in the log: 02/01/2010 10:45:48:1:2200: Module = vcpDiscover Function = GetObfuscatedName Source = vcpDiscover Error = Method '~' of object '~' failed(-2147467259:0:5003251) 02/01/2010 10:45:48:1:2200: Module = vcpDiscover Function = GetObfuscatedName Source = vcpDiscover Error = Method '~' of object '~' failed(-2147467259:0:5003251) Any tips? Using latest version, just downloaded it. Gabrie

    Read the article

  • slow disk writes between host and guest

    - by Jure1873
    I've got a ubuntu (server kernel) on a amd x4, 4gb ram, 2x seagate sata 1 tb disks for testing virtual machines and the write performance is very slow. The two disks are in a software raid1 array, one small boot ext3 partition, 10gb system partition and the rest is a xfs partition (about 980) gb for data (virtual machines). If I'm copying files from the virtual machine to the host with rsync or scp the copy frequently stalls or goes at about 1mb/s. What's wrong? I've tried disabling barriers on xfs, increased logbufs, allocsize, but it seems nothing helps. The strange thing is that await (for example during copying) for sda is usually under 100, while for sdb is around 400. Any ideas on what could be wrong / what could I do to improve this setup?

    Read the article

  • Assigning cores to VM in vSphere

    - by user114933
    Complete vSphere newbie here... Background: So, I have a 12 core machine with 24 VMs on it. Currently, all the processing power is shared between these VMs equally. The question: Can I configure one VM to be given two CPU's worth processing no matter what's happening on the other machines? My Research: I tried two things in vSphere... I set the reservation and limit on one VM to equal the same as two cores. To test if my objective was being reached, I measured the time it would take to gzip a file when other VMs were running nothing and when other VMs were running CPU intensive operations. I expected the time to gzip the file would be the same because this VM gets priority for some processing. Unfortunately, the time taken to gzip the file when other VMs were running something was significantly more than when other VMs were not running anything. I tried setting the Hyperthreaded Core Sharing mode to Internal hoping that this would mean that my VM would get at least an entire core to itself. This did not work either. Thanks in advance!

    Read the article

  • Deployment from OVA format

    - by Manvendra Bele
    I am deploying a VM using a OVA format. The size of OVA format is 57 GB. Currently free space on my datastore is 388 GB. At the time of selecting Disk Format type if shows me in red that the disk size required is 1 TB therefore you cannot select THICK provisioning. Therefore, i selected THIN provisiong. It THIN provisioing i am showed that Estimated Disk Usage is 112 GB which is less than the free space available. But even after selecting THIN proviosing at the time of deployment it throws an error that it cannot create disk as the size of disk is larger than the maximum specified limit. My block size is of 1 MB. Pasting my exact error here: Failed to deploy OVF package:File [datastore1] IMS Tester 1/IMS Tester1_2.vmdk is larger than maximum size supported by datastore 'datastore1

    Read the article

  • What hardware would I need (approx) to run ESXi server?

    - by mr.b
    Hi, I am considering to purchase off-the-shelf commodity hardware in order to build server that will host virtual machines using ESXi server. Intended purpose for this server is NOT mission critical tasks. It will have to run perhaps 20-50 Windows XP/Vista/7 virtual machines (in total, but closer to 20 figure). Each guest would have to have 1-2 GB of ram, and probably two-three times more disk space than guest OS needs with clean install and all updates applied (that would be around 6-8 GB for XP, and i believe closer to 10-15 for win7). Those guests will act as a test ground for a new product that is network management software, thus guests will idle most of their time once initially loaded, but if I give them some task to complete, they should be able to perform reasonably well. Now, from what I have learned... CPU is usually not much of an issue (6 cores would do it), memory should not be lacking, but doesn't have to be sum of all guests, because of overcommitment... That leads me to IO, which is, as it seems, the bottleneck. Since I have very little experience with ESXi (and ESX, too) server, I'd like to ask: How much memory could I save by overcommitment, and how does it affect performance? Is 6-core cpu enough to run above described system? Would it be possible to run entire server off two (or even one) SSD drives (to host system virtual disks, with few additional HDDs (2-3) in RAID 0 to be used as secondary storage? I read somewhere that ESXi allows having something like "master image", essentially virtual machine that is "deployed" many times, so that disk space can be saved by having only differences stored by specific guests, instead of copying around whole virtual disks. Is this true, and how can this help me? Are there any other things I need to take into consideration when building this off-the-shelf solution? I should probably mention here that I'm fully aware of issues like SPOF regarding power supply, raid 0, etc, but since it's only a testing ground and not a production system, it's not so important for me. Thanks, B.

    Read the article

  • Odd SVN Checkout failures occur frequenctly on VMWare virtual machines

    - by snowballhg
    We've recently been experiencing seemingly random SVN checkout failures on our Hudson build system. Google search has failed me; I'm hoping the super user community can help me out :-) We are occasionally receiving the following SVN error when our Hudson build jobs checkout source via the Hudson Subversion plug-in (which uses svn kit): ERROR: Failed to check out http://server/svnroot/trunk org.tmatesoft.svn.core.SVNException: svn: Processing REPORT request response failed: XML document structures must start and end within the same entity. (/svnroot/!svn/vcc/default) svn: REPORT request failed on '/svnroot/!svn/vcc/default' This issue seems to only occur when checking out from our Virtual Machines (Windows XP, Fedora 9, Fedora 12) using Hudson's SVN Plug-in. Systems that use the traditional SVN client seem to work. SVN Server version: 1.6.6 Hudson version: 1.377 Hudson SVN Plugin Version: 1.17 Has anyone dealt with this issue, or have any suggestions? Thanks

    Read the article

  • Clustering with Vsphere and Apache load balacing

    - by Anonymous2011
    I was looking at Vsphere to automatically load balance my apache web servers, and mysql servers but will this actually do the job? I know it says it does auto load balancing but not actually sure it quite means what I want to achieve. Is there an easier way to set up a php-apache and mysql cluster within virtual machines? Or are there any guides to clustering? (I have tried googling without much luck) Any help towards understanding/setting up clustering and load balancing within virtual machines appreciated.

    Read the article

  • Esxi with iSCSI SAN slows down with many multiple VMs running

    - by varesa
    I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas). Those two machines are connected to each other with Gigabit ethernet, and a procurve switch in between. After a while, if I have many(4-5 or more) vms running, they start to get un-responsive (long delays before anything happens). We are trying to find the reason behind this. Today we looked at esxtop, and found that DAVG of that iSCSI LUN stays at 70-80. I read that +30 is critical! What could be causing those high response-times?

    Read the article

  • Resource Pool sharing in Hyper-V Virtual Machines

    - by user67905
    I understand that we can install Hyper-V on one server and run a number of Virtual Machines on it, upto the limit of resources of that server. I want to know if it is possible to install Hyper-V lumped on two or more servers, so that the Virtual Machines can use the underlying resources pool of both the servers? And also if that same is possible for an “n” number of servers, instead of just 2 servers.

    Read the article

  • How can I know if a VM is used or not?

    - by Saariko
    I am running eSXI 4.1. In my main datastore I have plenty of folders, some of them has logical names, while the others don't, they hold BASE configurations/images of clients that I duplicate and activate. I only have a fraction of the actual clients loaded and running on the server. How can I know, but looking in the datastore folder, if the VM is in the inventory or not? If I right click on the vmx file, I can add it to the inventory - EVEN if the same client/folder is already active.

    Read the article

< Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >