Search Results

Search found 18803 results on 753 pages for 'c link'.

Page 603/753 | < Previous Page | 599 600 601 602 603 604 605 606 607 608 609 610  | Next Page >

• esx5 debian VM vlan setup

  - by Kstro21

  i have a server with ESX5, have a switch with about 20 vlans, this is how setup the trunk port interface GigabitEthernet0/1/1 description ToOper port link-type trunk undo port trunk allow-pass vlan 1 port trunk allow-pass vlan 2 to 14 stp disable ntdp enable ndp enable bpdu enable then, i created a standar switch(sw1) using the vSphere Client, the VLAN ID is set to All (4095), i also created a VM with Debian 6, with a NIC connected to sw1, now, i want to configure this NIC for a selected group of vlans auto vlan10 iface vlan10 inet static address 11.10.1.0 netmask 255.255.255.224 mtu 1500 vlan_raw_device eth0 auto vlan14 iface vlan14 inet static address 11.10.1.65 netmask 255.255.255.248 mtu 1500 vlan_raw_device eth0 so, when i restart the network using /etc/init.d/networking restart, i got this error Reconfiguring network interfaces...SIOCSIFADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFMTU: No such device vlan14: ERROR while getting interface flags: No such device Failed to bring up vlan14. done. this is just part of the error, so, my questions is: is this possible?, i mean, what i'm trying to achieve using ESX Virtual Machines, VLANS, etc is this a Debian problem? can be solved? i've read about a file named z25_persistent-net.rules in Debian but it doesn't exist in my installation. in the In the vSphere Networking for ESX5 guide, you can read: If you enter 0 or leave the option blank, the port group can see only untagged (non-VLAN) traffic. If you enter 4095, the port group can see traffic on any VLAN while leaving the VLAN tags intact. So, in theory, it should work, right? Hope you can help me up with this one Thanks

  Read the article

• How can I use my cell phone to establish a dial-up networking connection?

  - by gWiz

  I am using Windows 7 and have a BlackBerry with T-Mobile (U.S.). I have paired the phone with my computer over Bluetooth, which automatically creates a serial port for it. I am able to open the port in PuTTY and successfully issue AT commands to the modem, including dialing. However, while using Windows to create and establish a Dial-Up Networking connection, I get an error dialog stating "Error 678. The remote computer did not respond." In my testing, I also tried setting up a connection to dial a number connected to a phone. When attempting to connect over this connection, the phone does ring but the very moment I answer the call, my computer displays the above error dialog. What must be done to successfully establish such a PPP connection? Some special AT initialization string perhaps? To clarify, I'm not referring to the well-described and popular technique known as "tethering," in which the remote host of the data link is the mobile service provider. I am interested specifically in establishing direct data links with remote hosts other than my mobile service provider. Think old-school landline connection to your friend's computer or BBS. Edit 1 As grawity pointed out in comments, the missing piece of the puzzle is the actual modulator that is compatible with v-series protocols, which I expected to be built into the cellphone. So far the best only software alternative I could find is this experimental project. Edit 2 Found this forum discussion today. The participants state that there is no old-school modem in the BlackBerry. Edit 3 When I place a call in PuTTY with ATD, immediately after the call is answered (and the callee is initiating the handshake) the cellphone returns OK. This is not the expected behavior for establishing a data connection. The phone should reciprocate the handshake, and upon success return CONNECT. (Alternatively it should return BUSY or NO CARRIER, but never simply OK.) Windows DUN must be interpreting this as the "Error 678" I was seeing.

  Read the article

• Basic connectivity issues between Win 7 and XP mixed wired/wireless network.

  - by Pulse

  Setup: Windows 7 x64 Ultimate desktop hard wired to Asus WL500gp router (WL500gpv2-1.9.2.7-d-r1445 firmware) Several Bridged VirtualBox VM's running XP, 7, ubuntu server 10.04, Mint 9 and SuSE 11.2 Win XP Pro SP3 notebook with D-Link Airplus wireless network card. No firewall or other security software currently running on either platform (at least for the duration of the test) Situation: Router is acting DHCP server Clients are receiving correct addresses and additional parameters Internet connectivity is available from all clients Windows 7 sharing is set to Network type = work (not home group) NetBT is disabled on all clients using smb over TCP What I can do: I can ping the router and internet addresses from the wireless XP notebook I can ping the Win 7 desktop and any VM from the XP wireless notebook I can ping all devices from the router All VM's and 7 can ping each other and the router as well as Internet addresses What I can't do: I cannot ping the XP wireless notebook from either The Win 7 desktop or the VM's it alwats returns a destination host unreachable. Tracert resolves the name or the XP notebook but also returns a destination host unreachable. From the above it would seem that something is blocking connectivity in a single direction (from the Win 7 box to the Win XP notebook) only but the router can ping the XP notebook. Some fresh input would be most welcome, as this is beginning to drive me batty. Thanks

  Read the article

• A router that supports connecting with 2 different wifi networks

  - by Allan Deamon

  I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

  Read the article

• Doesn't VirtualBox 4.0 support drag-drop file copy yet?

  - by Benjamin

  Version 4.0.0 will be new major release. The following major new features were added: -New settings/disk file layout for VM portability; see the manual for more information. -Open Virtualization Format Archive (OVA) support; see the manual for more information. -VMM: support more than 1.5/2 GB guest RAM on 32-bit hosts -Language bindings: uniform Java bindings for both local (COM/XPCOM) and remote (SOAP) -invocation APIs -Chipset: added support for the Intel ICH9 chipset with 3 PCI buses, PCI express and -Message Signaled Interrupts (MSI) -Audio: Intel HD Audio is now available as guest hardware, for better support with modern -guest operating systems (e.g. 64-bit Windows; bug #2785). -GUI: redesigned user interface with guest window preview -GUI: new display mode with downscaled guest display -Resource control: added support for limiting a VM's CPU time and IO bandwidth. -Storage: support asynchronous I/O for iSCSI, VMDK, VHD and Parallels images -Storage: support for resizing VDI and VHD images -Windows Additions: support for automatically updating the Guest Additions (requires -installed Windows Guest Additions 4.0 or later) -Guest Additions: support for copying files into the guest file system What does the last line mean? I thought this is a drag-drop file copy feature like VMWare. I tried that. But I couldn't copy by drag-drop, ctrl-c ctrl-v either. Edit: I mean VBox 4.0 beta, not 3.x The release note is here. Download link is here.

  Read the article

• MS Excel and Access - which is better for reports?

  - by Nat

  Where I work, staff have just started to use a basic table in excel (1 october) to record sales which has about 10 columns (name, client, renewed, discount, paid etc). I record the data (total sold etc) every hour and email it to the manager. Each staff has the their own file on the network which they use constantly for that day (eg. John 08-10.xlsx; John 09-10.xlsx etc) and have been told to save the file after they complete a row with client data. I can see the file (in read only mode) to update the report but I am sure there must be a way of doing an autoupdate of their worksheets in real time. I can link worksheets and workbooks to my main workbook but manually. Does anyone have suggestions on have to do this on Excel? Or would Access allow me to make a report which shows the sales total for that hour without the staff closing the file or constantly clicking save every few minutes? We use office 2010. thanks

  Read the article

• How do I prevent a tar pipe from causing swapping?

  - by Jeff Shattock

  I have a rather large filesystem that I need to transfer from one Linux server to another. I figured the best way to do this was via a tar/netcat pipe arrangment, something like tar c . | pv | nc blah blah blah And it works great, the network stays fairly saturated, life is good. Until the source machine starts swapping. The files are on a raid on the source system, so the read speed is much faster than the write speed on the other end. Since the dest machine hasnt picked up the data yet, the source machine needs to stick it somewhere, so into RAM it goes, until there is no more free RAM. It then starts swapping, which is horribly painful since that machine has its OS installed on a somewhat slow CF card. Both machines have 4GB of physical ram, 64 bit Ubuntu 9.04 server. GigE link between them. How do I prevent this swapping? Can I put a "speed-limit" on the tar or netcat process so that the transfer speed doesn't overwhelm the write throughput on the destination end? The man pages didn't list anything, but there might be something I'm overlooking.

  Read the article

• nginx proxying different servers for different subdomains

  - by The.Anti.9

  i just set up an nginx server. On the same computer as nginx, I have apache running on port 8000 (this was previously set up.) and I want no subdomain and the www. subdomain to go to the local apache instance. But i want the stuff. subdomain to link to my server where i keep all my miscellaneous files (pictures, documents, etc.), which is also listening on port 80 at the ip 192.168.1.102. I tried configuring it, but when i go to my domain, I just get the "Welcome to nginx!". Here's what I have: user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; include /etc/nginx/conf.d/*.conf; server { listen 80; server_name theanti9.com www.theanti9.com; access_log /var/log/nginx/access.log; location / { proxy_pass http://localhost:8000; } } server { listen 80; server_name stuff.theanti9.com; access_log /var/log/nginx/access.log; location / { proxy_pass http://192.168.1.102:80; } } } I'm not really sure what's wrong. Any suggestions?

  Read the article

• Is it possible to use rsync over sftp (without an ssh shell) ?

  - by Tom Feiner

  Rsync over ssh, works great every time. However, trying to rsync to a host which allows only sftp logins, but not ssh logins, provides the following error: rsync -av /source ssh user@remotehost:/target/ protocol version mismatch -- is your shell clean? (see the rsync man page for an explanation) rsync error: protocol incompatibility (code 2) at compat.c(171) [sender=3.0.6] Here's the relevant section from the rsync man page: This message is usually caused by your startup scripts or remote shell facility producing unwanted garbage on the stream that rsync is using for its transport. The way to diagnose this problem is to run your remote shell like this: ssh remotehost /bin/true > out.dat then look at out.dat. If everything is working correctly then out.dat should be a zero length file. If you are getting the above error from rsync then you will probably find that out.dat contains some text or data. Look at the contents and try to work out what is producing it. The most com- mon cause is incorrectly configured shell startup scripts (such as .cshrc or .profile) that contain output statements for non-interactive logins. Trying this on my system produced the following in out.dat: ssh-dummy-shell: Command not allowed. As I thought, the host is not allowing ssh logins. The following link shows that it is possible to accomplish this task using fuse with sshfs - however it is extremely slow, and not fit for production use. Is there any chance of getting rsync sftp to work?

  Read the article

• Ubuntu 10.04 network manager issues

  - by Shark

  I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

  Read the article

• Ping with explicit next-hop selection (aka Monitoring multiple default gateways)

  - by Michuelnik

  I have a linux (debian) router with two internet connections (A) and (B). (A) is preferred, (B) is fallback. I want to monitor the internet connection (and not only the availability of the gateways!) and change the default route appropriately. If (A) is not providing internet, switch to (B) If (A) is providing internet again, switch back to (A). Only problem I have is in case (2). My routing table points towards a working internet so I cannot easily detect whether internet is working over link (A) again. I am search for a ping or traceroute (or other diagnosis-tool) which can select the next-hop explicitly. ping -r looks promising, but can only ping a host on the lan. (It only has to write another destination address in the packet, damnit!) traceroute -g gateway looks even more promising and nearly does what I want - but sets source routing options which my next-hops deny. (Not within my administrative boundary...) I just want a $ping, that can: select a source interface (and address) select a next-hop on that interface ping any arbitrary ip address I could do evil trickery with policy-based routing but that would have production impact for all users. I would like to see a side-effect-free solution....

  Read the article

• Equivalent of scp -l bandwidth_cap for .ssh/config?

  - by Mark Bennett

  Short form: You can limit the bandwidth the scp uses with the -l switch, you pass a number that's in kbits/sec. I'd rather set this in my .ssh/config file for certain names machines. What's the equivalent named setting for -l ? I haven't been able to find it. Followup question: Generally, not sure how to map back and forth between ssh command line options and config names, short of doing Google searches or manually comparing man pages on a case by case basis. Is there a table that directly equates the two? Longer form of first question, with context: I've started using ssh config quite a bit, especially now that I need to go through a proxy and do lots of port mappings. I even define the same machine more than once depending on what type of tunneling I need. However, when uploading a large file, it's difficult to do anything else on my machine. Even though I have more download bandwidth than up, I think that scp saturates the link so even my small requests can't reach the Internet. There's a fix for this, using the -l bandwidth command line switch for scp. scp -l 1000 bigfile.zip titan: I'd like to use this in my config instead, so I'd create an additional named entry called "titan-upload" and I'd use that as the target whenever I upload. So instead of: scp bigfile.zip titan: I'd say: scp bigfile.zip titan-upload Or even set different caps depending on where I am: scp bigfile.zip titan-upload-from-home vs. scp bigfile.zip titan-upload-from-work I'm generally on Mac and Linux.

  Read the article

• How to have LiveJournal delegate my OpenID to something else?

  - by T-Boy

  I understand that if I have full control over my domain, I can set it up so that I can delegate the task of authenticating to another OpenID service provider. The problem is, what I'd like to do is to get the LiveJournal server to pass the authentication to someone else, instead of having LJ doing it. Preferably what I'd like to do is get LiveJournal, when asked by a web site, say, "No, I don't do it anymore -- go to this address". The plan was that this address would then be in a domain I fully control, which then would pass it on to whichever service provider I choose. I don't even know if I've gotten my understanding of OpenID right, if all this shenanigans are necessary, if my question makes sense, or if it's even possible with a service provider like Livejournal. ETA: Doing a little more reading up, and examining the source for my LiveJournal user page, I note that this particular line in the file's <header> area: <link rel="openid.server" href="http://www.livejournal.com/openid/server.bml" /> I suspect that changing this will allow me to forward OpenID requests to whomever I wish, I think; so far so good. Now comes the hard part -- figuring out how to change all of that using LiveJournal's customization options, if that is at all possible (here's hoping I don't need to pay to get that functionality).

  Read the article

• Low-profile, PCI Express, x1 video card with VGA-out?

  - by Dandy

  I just bought an Acer Aspire EasyStore H340 system (http://us.acer.com/acer/productv.do?LanguageISOCtxParam=en&kcond61e.c2att101=54825&sp=page16e&ctx2.c2att1=25&link=ln438e&CountryISOCtxParam=US&ctx1g.c2att92=450&ctx1.att21k=1&CRC=936243954) It comes with Windows Home Server, which I don't particularly care for (too dumbed down for my liking)--I bought the box mainly for the form factor, and intend to install Server 2008 on it and have it run as a small domain controller. The geniuses at Acer however went out of their way to ensure you can only run Home Server--you can only connect to it via the Home Server Connector software, as it has no video-out whatsoever (so essentially, there's no way to even get into the BIOS). It only has a low-profile, PCI Express x1 slot. It turns out to be way harder than I thought to locate a video card that both has an x1 connector, and is low-profile (I'd really rather not snip the bracket at the back just so it'll fit the case). I know they're out there, and I've seen one with Display Port outputs, but I don't have a monitor with this connection. So to reiterate, it needs to be: - x1 connector - low profile - VGA out (though DVI would be okay; I have some spare adapters) Can anyone recommend anything at all?

  Read the article

• Debian Wheezy IPv6 isn't configured with ifup post-up hook

  - by aef

  We recently set up a server on Debian Wheezy Beta 3 (x86_64) which has a native IPv6 connection. We configured the eth0 interface to get the IPv6 configuration through some post-up hook commands in /etc/network/interfaces. The result is, that after the booting the system up, there is only IPv4 and an auto-configured link-local IPv6 address configured on the interface, as if the command has never been executed. When we additionally place the commands after the call to ifup -a inside the /etc/init.d/networking init script, everything works as expected and we have a fully configured interface after booting up. This is quite an ugly way to configure the interface. What are we doing wrong with the ifup post-up hooks? Or is this a bug? The section from /etc/network/interfaces looks like this (IP-addresses changed): allow-hotplug eth0 iface eth0 inet static address 1.2.3.1 netmask 255.255.255.192 network 1.2.3.0 broadcast 1.2.3.63 gateway 1.2.3.62 dns-nameservers 8.8.8.8 dns-search mydomain.tld post-up ip -6 addr add 2001:db8:100:3022::2 dev eth0 post-up ip -6 route add fe80::1 dev eth0 post-up ip -6 route add default via fe80::1 dev eth0 I also tried it in this alternative way: auto eth0 iface eth0 inet static address 1.2.3.1 netmask 255.255.255.192 network 1.2.3.0 broadcast 1.2.3.63 gateway 1.2.3.62 dns-nameservers 8.8.8.8 dns-search mydomain.tld iface eth0 inet6 static address 2001:db8:100:3022::2 netmask 64 gateway fe80::1 What we added to /etc/init.d/networking: … case "$1" in start) process_options check_ifstate if [ "$CONFIGURE_INTERFACES" = no ] then log_action_msg "Not configuring network interfaces, see /etc/default/networking" exit 0 fi set -f exclusions=$(process_exclusions) log_action_begin_msg "Configuring network interfaces" if ifup -a $exclusions $verbose && ifup_hotplug $exclusions $verbose # Our additions ip -6 addr add 2001:db8:100:3022::2 dev eth0 ip -6 route add fe80::1 dev eth0 ip -6 route add default via fe80::1 dev eth0 then log_action_end_msg $? else log_action_end_msg $? fi ;; …

  Read the article

• Why database partitioning didn't work? Extract from thedailywtf.com

  - by questzen

  Original link. http://thedailywtf.com/Articles/The-Certified-DBA.aspx. Article summary: The DBA suggests an approach involving rigorous partitioning, 10 partitions per disk (3 actual disks and 3 raid). The stats show that the performance is non-optimal. Then the DBA suggests an alternative of 1 partition per disk (with more added disks). This also fails. The sys-admin then sets up a single disk, single partition and saves the day. The size of disks was not mentioned but given today,s typical disk sizes (of the order of 100 GB), the partitions ; would be huge, it surprises me that a single disk with all partitions outperformed. Initially I suspect that the data was segregated and hence faster reads. But how come the performance didn't degrade as time went by with all the inserts and updates happening? Saw this on reddit, but the explanation was by far spindle/platter centered. There was no mention in the article about this. Is there any other reason? I can only guess that the tables were using a incorrect hash distribution causing non-uniform allocation across disks (wrong partitioning); this would increase fetch times. Any thoughts?

  Read the article

• Recommend a UK based VPS host equivalent to Dreamhost [closed]

  - by Pez Cuckow

  I appreciate this question could be considered subjective and argumentative so can people make recommendations rather than arguing about the best. I believe the "correct" answer is the one closest to what I am looking for. Basically I live in the UK but have been using the US based Dreamhost for about 6 years now, and my web projects are getting to the scale where the websites need to the UK based to cope with the demand and load. I originally had shared hosting with Dreamhost but upgraded to a VPS a while ago, getting 512mb of RAM, unlimited disk space, bandwidth and domains for $30. Their control panel is a custom easy to use build that they have created in house and offers features very similar to other web panels (as far as I am aware). So basically my question boils down to, is there anywhere that offers an equivalent package? In all honesty as long as I have over 50gb HDD space and unlimited domains it doesn't really matter? Are there any VPS providers you would recommend as reliable? I promise to check every link posted, many thanks for your time!

  Read the article

• What could be wrong with my VLAN?

  - by Matt

  I've got a VLAN 10 setup as a management VLAN. The management VLAN comes off port 48 and links to another set of switches that do not support VLAN's so it was I believe set up as an untagged access port. In the past this was a different brand of switch and this worked fine. However, since changing to the HP V1910-48G series I can't seem to get this working. I must point out that as far as I'm aware it is wired up properly (I can't check this physically as I'm working remote and have asked the tech who's got access to double check for me). Now I don't have a huge amount of experience with VLAN environments but AFAIK this is right. I've set the port 48 (linked to the management switches) as an untagged port with PVID 10 and access link type. Is this all I'd need to do from a configuration perspective to ensure all devices connected to port 48 would end up being on VLAN 10 and not needing to tag their frames. i.e. the tag would be added by the switch before being forwarded.

  Read the article

• Sync Local ICS File with Android via Exchange/Outlook

  - by sinDizzy

  At my company we have a 3rd party app which tracks off-hours duty for all of our engineers. The app is not web-enabled and we cannot make any changes to it. It does write a simple text file and I have created an app that translates that to an ICS file. My goal is to have that appear on my calendar on my Android phone. Here is the path I am working on: DutyApp -- TextFile -- ICSFile -- Outlook(exchange) -- Android (via exchange sync) My problems: If I place the ICS file on our FILE server and then in Outlook if I go to the option CalendarOpen CalendarFrom Internet it shows up in Outlook and looks pretty good. After a couple minutes it shows up on my Android phone as well. If I change the original ICS file those changes never display in Outlook and never sync to my Android phone. This seems to be a one shot deal almost like an import. Now if I place the ICS file on our WEB server and then in Outlook if I go to the option CalendarOpen CalendarFrom Internet and use webcal:\ as the address, it shows up in Outlook and also looks pretty good. Any changes I make to the original ICS file display in Outlook. However the entire calendar never shows up in Android. This calendar is a subscription and it seems, although am not sure, that Android doesn't display Exchange subscription calendars. Yes I know it works with Gmail subscription calendars but this is Exchange. So my question is what other options are there? We are behind a firewall so cant link the ICS file to a Gmail account. I can't put the ICS file anywhere else other than our file or web server.

  Read the article

• Steps to deploy a custom routing protocol

  - by user134589

  I'm a Ph.D Student and I'm researching a Service Centric Networking architecture with resourceallocation on a large scale. What I'm looking to do is expand an existing routing protocol like OSPF with extra fields and some new message types that I need for communication between Nodes. I want to manipulate the cost of a network link and I want paths to be calculated like in OSPF V2/v3, but using the cost that my algorithms have calculated. What I have I have the source code of OSPF from Quagga. I am assuming I can edit this code how I want, including packet structures and creating new types. Yes, I am aware it won't be easy but this is a 6 years research project and I am eager to develop something new, to move forward. What I need I would like to know how I can deploy the edited OSPF source files I have (written in C) on any type of server. I have a large testbed environment available with hundreds of virtual nodes and pretty much any OS out there. So if I want to test my extended protocol, how do I make all the nodes in a network use this to communicate? I do not understand what parts of the kernel I need to edit here. I tried searching for days now and I am unable to find how to deploy a non-existing routing protocol, without the use of an application-level framework. If somebody could push me in the right direction that'd be awesome. note: I need this to be a routingprotocol and not an application, since I want this to work on op of the network layer for performance reasons. Thanks!

  Read the article

• Nginx: Disallow index.html in URL

  - by Martin Vilcans

  We're generating a site consisting of only static files (using Assemble). Having the .html extension on URLs looks so nineties, so we generate every static HTML file in its own directory and call it index.html. For example, the url http://www.example.com/foo/bar/ is in the file /var/www/foo/bar/index.html. This works well, but there is one small thing nagging me: Now there are two possible URLs to the same resource: http://www.example.com/foo/bar/ (slash URL) http://www.example.com/foo/bar/index.html (index.html URL) By accident someone may link to the index.html form of the URL, which is bad for SEO and looks ugly (remember the nineties?). Is it possible in Nginx to give a 404 error on the index.html URL, but serve the slash URL? I tried this: location ~ /index\.html$ { return 404; } But it seems that Nginx does some internal rewrite of the slash URL to the index.html URL, and then matches this location so we get a 404 even on the slash URL. Note that to catch mistakes, we want index.html URLs to be an error, not just redirect to the slash URL.

  Read the article

• How to add "create a new python file" to the registry

  - by Anthony

  I have Python 3.2 on a windows 7 operating system. The other day I thought that it would be convenient to add a link to create a new .py file in the right hand click "new" menu. I had worked with the registry before and looked up how to add an item to the "new" menu, but when I got to the registry under HKEY_CLASSES_ROOT the .py extension key was not there. I only know how to add something to the "new" menu using the extension key. I searched the web, but could not come up with any other ways. Python works perfectly fine, and I don't want to mess anything up by adding the extension key. So here are my questions: Will I mess up python or something else by adding a .py key?( I know it is dangerous to work with the registry, that is why I am looking for a safe solution) If not how can I go about doing this? OR Is there a different way to add "create a new python file" to the "new" menu? If so how can I do it? OR If the only way is very complicated should I forget about it? Thank you in advance. P.S I originally posted on Stack Overflow that they told me to move it over here.

  Read the article

• Get the Windows Scheduler's Location Or Code?

  - by Ram

  Today i got a task to find the scheduler that is running once in a month, actually I have to change its running time period to once a week. I have searched for it in the Windows scheduled tasks, but i didn't find it. It is sending a mail containing a link. Now i am not confused about this where else can i find it. As the place i know where the scheduler can be, has already been checked by me. Can someone suggest me where else can i search for this scheduler? As per the previous developer's comment "It is a normal Windows method of scheduling tasks" UPDATE Actually the task is running after a month periodically. As per my knowledge it could be a "Windows Task Schedule" or "Windows Service" created by the old developer. Now as the previous developer is not available and i do not have any documentation.. i need to change the time period from month to weakly. I have checked in the "Task Schedules" on the server and checked the services running ob the server and was unable to find the "Scheduler". now i have two questions: is there any other approach by using that i can schedule an automated email periodically. any idea to find this.

  Read the article

• Nginx Server Block Not Working? - Already running other vhosts just this one not working

  - by daveaspinall

  Im running a Debian 6 LEMP server with multiple virtual hosts and everything has been fine for 5 or so sites. But I've just tried adding another but for some reason it's just not working. By not working I mean in Chrome I get the "Oops! Google Chrome could not connect to subdomain.domain.net" error. I've changed the domain for security to subdomain.example.com and the IP is masked. Hosts file (I have multiple sub domains): xxx.xxx.xx.xxx *.example.com *.example Server Block: server { listen 80; server_name subdomain.example.com; access_log /srv/www/subdomain.example.com/logs/access.log; error_log /srv/www/subdomain.example.com/logs/error.log; root /srv/www/subdomain.example.com/public_html; location / { index index.html index.htm index.php; } location ~ \.php$ { include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } } I've created the system link to the file in the /etc/nginx/sites-enabled/ directory and restarted/reloaded nginx. DNS seems fine: # ping -c 2 subdomain PING subdomain.example.com (xxx.xxx.xx.xxx) 56(84) bytes of data. 64 bytes from www.example.com (xxx.xxx.xx.xxx): icmp_req=1 ttl=64 time=0.035 ms 64 bytes from www.example.com (xxx.xxx.xx.xxx): icmp_req=2 ttl=64 time=0.048 ms Checking the file with cURL works: # curl http://subdomain.example.com HTML - OK Emptied browser cache but still no dice. Anything I'm missing? Like I mentioned, I have a few sites running fine on the server currently so php-fpm etc etc are working. Any help would be much appreciated! Cheers, Dave

  Read the article

• How to connect computers to a network printer behind a router?

  - by kokbira

  General question: How to connect computers to an IP printer behind a router? Particular question: How to connect C-1 and C-2 to PRI? What? Where? [ISP] | | -> IPs:200.X.X.X/other configs:DC | [R-1] | | -> IPs:10.1.X.X locked by MAC,M:255.0.0.0,G:10.1.0.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [PRI] IP:10.1.7.7 [R-2] IP: 10.1.0.1,MAC:A | | -> IPs:192.168.1.X,M:255.255.255.0,G:192.168.1.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [C-1] IP:192.168.1.2 [C-2] IP:192.168.1.3,MAC:A Glossary and details: ------------------------------------------------------------------------------------ - IP: IP. - IPs: Some IP range. - M: Mask. - G: Gateway. - MAC:A: A MAC address that I will not inform you :) - DC: Don't care. - ISP: Internet Service Provider (not so much details about it on that case). - R-1: A real router or some concatenated so IP range bellow that block is 10.1.X.X and above is ISP. The provided IPs are provided by MAC. As all available addresses are in use, you must clone an existing one to join with a new device (and to disconnect the cloned one). - PRI: An network printer (some people here call that IP printer). - R-2: A TP-LINK TL-WR340G, mine wireless router (since my computer does not have ethernet input, it is my ethernet-wifi adapter :), admin access, MAC address cloned from C-2 (MAC:A). I've to configure 10.0.1.1 and 10.0.1.2 as DNS addresses, other wise I cannot connect C-1 and C-2 to Internet. - C-1: My computer, a CCE XLE-425 (remember: no ethernet input), with Windows 7, admin access. - C-2: another computer with better configs than mine, MAC:A, Windows XP. Requirements: I want to print, to access Internet and to do it myself (no need to call network admin men in black people). Pay attention to MAC clones and DNS info.

  Read the article

< Previous Page | 599 600 601 602 603 604 605 606 607 608 609 610  | Next Page >