Search Results

Search found 17749 results on 710 pages for 'connection pool'.

Page 604/710 | < Previous Page | 600 601 602 603 604 605 606 607 608 609 610 611  | Next Page >

• Netgear router keeps disconnecting iPhone

  - by DisgruntledGoat

  My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

  Read the article

• FreeBSD 8 and Samba 3.3 Samba seems to crash/not start?

  - by scraft3613

  I am both new to FreeBSD and Samba, and with that in mind ... I installed Samba 3.3. from Ports. I have this in my rc.conf: #samba nmbd_enable="YES" smbd_enable="YES" winbindd_enable="YES" I can see an active PID: prod1# cat /var/run/smbd.pid 24426 But it seems like smbd isn't running: prod1# ps -auwxx | egrep '[sn]mbd' root 24513 0.0 0.3 21108 4672 ?? Ss Sat02PM 0:00.71 /usr/local/sbin/nmbd -D -s /usr/local/etc/smb.conf If I restart samba with /usr/local/etc/rc.d/samba restart it runs: prod1# ps -auwxx | egrep '[sn]mbd' root 30188 0.0 0.3 21080 4700 ?? Ss 2:49PM 0:00.00 /usr/local/sbin/nmbd -D -s /usr/local/etc/smb.conf root 30196 0.0 0.6 35520 10952 ?? Ss 2:49PM 0:00.00 /usr/local/sbin/smbd -D -s /usr/local/etc/smb.conf root 30198 0.0 0.6 35520 10880 ?? S 2:49PM 0:00.00 /usr/local/sbin/smbd -D -s /usr/local/etc/smb.conf Until I do: prod1# smbclient -L prod1 Connection to prod1 failed (Error NT_STATUS_CONNECTION_REFUSED) prod1# prod1# ps -auwxx | egrep '[sn]mbd' root 30188 0.0 0.3 21080 4700 ?? Ss 2:49PM 0:00.00 /usr/local/sbin/nmbd -D -s /usr/local/etc/smb.conf What should I be checking to find out what's going on?

  Read the article

• Procurve Primary VLAN

  - by fukawi2

  I'm trying to depreciate usage of VLAN 1 on my ProCurve switches; 1 is unused. I understand that VLAN 1 must exist, but I want to remove it from all ports, especially trunks between switches. The problem I have is that stacking does not seem to work without VLAN 1. I have changed the primary VLAN and management VLAN on all the switches: (config)# primary-vlan 42 (config)# management-vlan 42 (config)# no vlan 1 untagged 25 Port 25 is the link between the 2 switches I'm testing with; the stack master and a member switch; I only want tagged traffic between the switches, no untagged frames. show stacking on the master shows all members as "UP" but I can not telnet any of them: Telnet failed: Connection timed out. All switches have manually assigned (static) IP addresses on VLAN 42, and all exist in the same /25 subnet, as does my desktop. I can telnet the switches directly from my desktop to the individual switch IP addresses, just not from the master switch. Do I need to reboot the switches to have the primary-vlan change take effect? Or is there something else I'm missing?

  Read the article

• After connecting wlan0 to bridge interface (and then removing it), can't connect to AP

  - by gmonk

  I'm on a laptop running Debian Jessie with kernel 3.13-1-amd64; lspci shows that my wireless NIC + driver is 04:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83) Subsystem: Intel Corporation Dual Band Wireless-AC 3160 Kernel driver in use: iwlwifi This has been working without any problems, until I tried creating a bridge for lxc containers to use. I did the same thing as this person here: How-to set up a network bridge on a laptop for LXC use? -- and ended up having the same problem as this poster did, so I decided to "undo" my actions. This hasn't been successful. Actions taken so far: To configure the bridge: #> ip link add type veth #> iw dev wlan0 set 4addr on #> ifconfig veth0 up #> brctl addbr br0 #> brctl addif br0 wlan0 #> brctl addif br0 veth0 #> ifconfig br0 192.168.0.4/24 #> ifconfig wlan0 0.0.0.0 To "deconfigure": #> brctl delif br0 wlan0 #> brctl delif br0 veth0 #> iw dev wlan0 set 4addr off #> ifconfig veth0 down #> ifconfig wlan0 down #> ifconfig br0 down #> brctl delbr br0 Now, dmesg and /var/log/syslog show repeated attempts at connecting to the AP that was working before, which fail after authentication: May 27 09:16:01 myhostname kernel: [11350.757172] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:01 myhostname kernel: [11350.759036] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:01 myhostname kernel: [11350.762615] wlan0: authenticated May 27 09:16:01 myhostname kernel: [11350.762753] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.762755] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.765080] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:01 myhostname kernel: [11350.767474] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:01 myhostname kernel: [11350.767476] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:01 myhostname kernel: [11350.788475] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:02 myhostname dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14 May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname kernel: [11354.559579] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.561458] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> associating May 27 09:16:04 myhostname kernel: [11354.563445] wlan0: authenticated May 27 09:16:04 myhostname kernel: [11354.563631] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.563633] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.565727] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.568091] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:04 myhostname kernel: [11354.569030] wlan0: associated May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:05 myhostname kernel: [11354.978204] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:05 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:05 myhostname kernel: [11354.992729] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:05 myhostname kernel: [11354.995004] cfg80211: World regulatory domain updated: May 27 09:16:05 myhostname kernel: [11354.995005] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:05 myhostname kernel: [11354.995006] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995008] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995009] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995010] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.763968] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:09 myhostname kernel: [11358.765796] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.769957] wlan0: authenticated May 27 09:16:09 myhostname kernel: [11358.770102] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770104] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770846] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname kernel: [11358.773358] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:09 myhostname kernel: [11358.773361] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:09 myhostname kernel: [11358.802187] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.573442] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.575270] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.580334] wlan0: authenticated May 27 09:16:12 myhostname kernel: [11362.580503] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.580516] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.583508] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.585908] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:12 myhostname kernel: [11362.586781] wlan0: associated May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:13 myhostname kernel: [11362.947693] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:13 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:13 myhostname kernel: [11362.973461] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:13 myhostname kernel: [11362.975673] cfg80211: World regulatory domain updated: May 27 09:16:13 myhostname kernel: [11362.975675] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:13 myhostname kernel: [11362.975676] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975677] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0/wireless): association took too long. May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: config -> failed (reason 'no-secrets') [50 120 7] May 27 09:16:14 myhostname NetworkManager[13992]: <info> Marking connection 'Auto myaccesspoint' invalid. May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0) failed for connection 'Auto myaccesspoint' May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): deactivating device (reason 'none') [0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> disconnected The things that jump out at me are "deauthenticating ... by local choice( reason=3)" and the lines that contain "(reason=15)". I've tried various fixes: iwconfig wlan0 power off killing wpa_supplicant connecting with iwconfig + dhclient instead of gnome's network -manager explicitly configuring wlan0 in /etc/network/interfaces creating a /etc/wpa_supplicant.conf file ...but nothing seems to work. I'm not sure what I did wrong, or what step I've skipped in trying to get wlan0 back as a non-bridged device -- I removed it from the bridge and then deleted the bridge itself. Any ideas?

  Read the article

• How to connect 2 routers (Asmax and D-link)

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• Apache Server not working in MAMP

  - by jasonaburton

  Here's what I did before the problem started: I was creating a database for a site that I am working on in phpMyAdmin. I wrote some code to try to connect to the database I just created and I couldn't connect. I assumed it might be because I needed a password to connect to the database, so I created a password for it. Immediately after I created the password phpMyAdmin kicked me out saying: "#1045 - Access denied for user 'root'@'localhost' (using password: YES)" "phpMyAdmin tried to connect to the MySQL server, and the server rejected the connection. You should check the host, username and password in your configuration and make sure that they correspond to the information given by the administrator of the MySQL server." I found the php.ini file and searched for where I could change the password to match the one I just made, but couldn't find where I needed to change it. So I decided to scrap the database and uninstall MAMP from my computer and reinstall it hoping it would just reset all the defaults and I could go on my merry way. But now after reinstalling MAMP and trying to run the servers Apache won't start up and I have no idea why. One problem after another... Any advice or helpful ideas?

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• Netflix streaming stops loading at 98% on Revo 3700

  - by Martin Harris

  I'm trying to stream Netflix on an Acer Revo 3700 running Windows 7 Home Premium, but it hangs on the loading screen at 98% (after it has formatted the player to the right aspect ratio and added the controls, but before the video starts) with no error messages or failures. I have two other machines on the same network, one running Windows 7 Home Premium and another running XP, which both stream faultlessly. Things I have tried: Both a wired and wireless connection to the router Upgrading the video and audio drivers IE, Chrome and Firefox Boxee software Connecting with a VGA cable instead of HDMI (in case it is a HDCP thing) Uninstalling and reinstalling Silverlight. Getting someway into loading a HD movie and turning "Allow HD" off Does anyone know what Netflix is doing at the 98% load mark? Are there any log files? Anything else worth trying? Full disclosure: I'm using Netflix from the UK through a US based VPN. I've tried multiple VPNs and the problem is exactly the same, also the other machines on the same network through the same VPN work fine so I don't think this is the issue, but it might be a factor. The region check happens at around 7% and I get past that.

  Read the article

• Virtual Machine Network Services causes networking problems in Vista Enterprise 64 bit install

  - by Bill

  I have a Quad-core/8GB Vista Enterprise 64-bit (SP2) installation on which I installed Virtual PC 2007. I have a problem that is opposite of all that I found searching around the Internet--everybody has problems making network connections from their guest VM. When Virtual Machine Network Services is enabled in the protocol stack for my network card across a reboot, it causes access problems to the network. The amount of time to login in using a domain credentialed account is upwards of 3 minutes, then after reaching the desktop the network and sharing center shows that my connection to the domain is unauthenticated. Disabling and re-enabling the Virtual Machine Network Services (uncheck in network properties/apply/recheck/apply) fixes the problem. And as long as I have the VMNS disabled when I shutdown the restart runs smoothly. I just have to remember to enable after login and disable before shutdown. I have un-installed and re-installed Virtual PC 2007 multiple times with restarts between. The install consists of the SP1 + a KB patch for guest resolution fix. Any help would be greatly appreciated. Some additional information... At one point during my hairpulling and teethgnashing with this, I tried to ping my primary DC and observed some weird responses: (Our DC is 10.10.10.25, my dynamic IP was 10.10.10.203) Reply from 10.10.10.203, Destination host unreachable. Request timed out. Reply from 10.10.10.25: ... This is not consistently repeatable, but thought it might strike a chord with someone.

  Read the article

• Heartbeat/DRBD failover didn't work as expected. How do I make the failover more robust?

  - by Quinn Murphy

  I had a scenario where a DRBD-heartbeat set up had a failed node but did not failover. What happened was the primary node had locked up, but didn't go down directly (it was inaccessible via ssh or with the nfs mount, but it could be pinged). The desired behavior would have been to detect this and failover to the secondary node, but it appears that since the primary didn't go full down (there is a dedicated network connection from server to server), heartbeat's detection mechanism didn't pick up on that and therefore didn't failover. Has anyone seen this? Is there something that I need to configure to have more robust cluster failover? DRBD seems to otherwise work fine (had to resync when I rebooted the old primary), but without good failover, it's use is limited. heartbeat 3.0.4 drbd84 RHEL 6.1 We are not using Pacemaker nfs03 is the primary server in this setup, and nfs01 is the secondary. ha.cf # Hearbeat Logging logfacility daemon udpport 694 ucast eth0 192.168.10.47 ucast eth0 192.168.10.42 # Cluster members node nfs01.openair.com node nfs03.openair.com # Hearbeat communication timing. # Sets the triggers and pulse time for swapping over. keepalive 1 warntime 10 deadtime 30 initdead 120 #fail back automatically auto_failback on and here is the haresources file: nfs03.openair.com IPaddr::192.168.10.50/255.255.255.0/eth0 drbddisk::data Filesystem::/dev/drbd0::/data::ext4 nfs nfslock

  Read the article

• Ubuntu 10.04->10.10 in failed state - how to recover?

  - by Harvey

  I was running Ubuntu 10.04 and attempted to upgrade to 10.10. I have a really slow connection (DSL 128kbits/sec) and copying the upgrade files took about 26 hours. I of course let it run unattended. When I came back, I notice the following 3 dlgs: (1) "Could not install the upgrades The upgrade has aborted. Your system could be in an unusable state. A recovery will run now (dpkg -- configure -a)." (2) "gpk-update-icon Distribution upgrades available maverick 10.10 (stable) [more information] [Do no show this again] [Cancel] [Ok]" (3) "gpk-update-icon Security updates available The following important updates are available for your computer: libwebkit-1.0-2-dbg - Web content engine library for Gtk+ - Debugging symbols libcupsimage2 - Common UNIX Printing System(tm) - Raster image library ..." What is the best response to all of this? I went through something similar in an attempted network upgrade from 8.04 to 10.04 and had to reload the unbootable machine fresh from distribution media (all data was lost). I'd like to avoid that here. I have not yet responded to the dialogs, and want to make sure the system is still bootable and not lose my data this time.

  Read the article

• Debian Bluetooth headphones not working

  - by cYrus

  Hardware Headphones Bluetooth dongle Maybe not exactly these models. Setup I tried to follow some guides, here's what I've done so far: Install software: sudo apt-get install bluez-utils bluez-alsa Reboot (just to be sure): $ dmesg | grep -i bluetooth [ 20.268212] Bluetooth: Core ver 2.16 [ 20.268230] Bluetooth: HCI device and connection manager initialized [ 20.268233] Bluetooth: HCI socket layer initialized [ 20.268235] Bluetooth: L2CAP socket layer initialized [ 20.268239] Bluetooth: SCO socket layer initialized [ 20.284685] Bluetooth: RFCOMM TTY layer initialized [ 20.284692] Bluetooth: RFCOMM socket layer initialized [ 20.284693] Bluetooth: RFCOMM ver 1.11 [ 20.335375] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 20.335378] Bluetooth: BNEP filters: protocol multicast The deamon is running: $ /etc/init.d/bluetooth status [ ok ] bluetooth is running. Plug the dongle: $ dmesg | tail [...] [23108.352034] usb 5-2: new full-speed USB device number 2 using ohci_hcd [23108.571131] usb 5-2: New USB device found, idVendor=0a12, idProduct=0001 [23108.571136] usb 5-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [23108.629042] usbcore: registered new interface driver btusb Put the headphones in pairing mode, and try scanning: $ hcitool scan Scanning ... Found nothing. What's next? What should I try? I'll update this answer as soon as you provide me hints.

  Read the article

• I've just set up FreeBSD 8.0 and can't login with ssh

  - by Matt

  /etc/hosts.allow is set to allow any protocol from anywhere. I can "ssh localhost" and it works. I simply get "connection refused" from putty on another machine. Any ideas? Will try to get a copy of the sshd_server.conf file as soon as I can find a flash disk to copy it to, but I thought someone might know what you need to set initially to permit login. EDIT: I think I can see why it's not working now. If I telnet to the IP address of the server I'm seeing MGE UPS SYSTEMS SNMP Web/Agent configuration menu. Enter Password: Doh. Ok, so the IP address is assigned by DHCP, but it seems there is already a device statically assigned to that address. I'll put in a reservation and try again. ok, sorted now. It was an ip address conflict. Windows DHCP isn't smart enough to check if there is something listening on the address before first assigning it.

  Read the article

• Setting up port forwarding for web server

  - by Javier Badia

  This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

  Read the article

• How do I log back into a Windows Server 2003 guest OS after Hyper-V integration services installs and breaks my domain logins?

  - by Warren P

  After installing Hyper-V integration services, I appear to have a problem with logging in to my Windows Server 2003 virtual machine. Incorrect passwords and logins give the usual error message, but a correct login/password gives me this message: Windows cannot connect to the domain, either because the domain controller is down or otherwise unavailable, or because your computer account was not found. Please try again later. If this message continues to appear, contact your system administrator for assistance. Nothing pleases me more than Microsoft telling me (the ersatz system administrator) to contact my system administrator for help, when I suspect that I'm hooped. The virtual machine has a valid network connection, and has decided to invalidate all my previous logins on this account, so I can't log in and remotely fix anything, and I can't remotely connect to it from outside either. This appears to be a catch 22. Unfortunately I don't know any non-domain local logins for this virtual machine, so I suspect I am basically hooped, or that I need ophcrack. is there any alternative to ophcrack? Second and related question; I used Disk2VHD to do the conversion, and I could log in fine several times, until after the Hyper-V integration services were installed, then suddenly this happens and I can't log in now - was there something I did wrong? I can't get networking working inside the VM BEFORE I install integration services, and at the very moment that integration services is being installed, I'm getting locked out like this. I probably should always know the local login of any machine I'm upgrading so I don't get stuck like this in the future.... great. Now I am reminded again of this.

  Read the article

• can't get to admin page after factory reset netgear wg602

  - by stefanB

  I have wireless Netgear wg602 on my home network (connected to my internet modem/router). I've had it secured and locked down to only accept connection from specific MAC addresses. I've forgotten the password that I used but my Mac Book laptops can still connect (multiple OS updates - it can't retrieve and display the password but it can use it to log in to WPA) so I want to reconfigure it from scratch (have some new devices). I tried to reset the Netgear wg602 to factory settings (pressed reset button for 10 sec), reset my laptop IP address to local address suggested in manual (192.168.0.210 net mask 255.255.255.0), connect Netgear via ethernet cable to my mac book pro but I can't get to the admin page at 192.168.0.227 as suggested by manual (firefox or safari). At this stage the Netgear is not connected to router, it is only connected to mac book. I can't ping the wireless access point either (but it is on all lights are on). What am I doing incorrectly? Last time I configured it via Windows now I only have Mac Book (which I've used with the wireless access point for 2 years so no compatibility problems).

  Read the article

• Encrypted WiFi with no password?

  - by Ian Boyd

  Is there any standard that allows a WiFi connection to be encrypted, but not require a password? i know that (old, weak) WEP, and newer WPA/WPA2 require a password (i.e. shared secret). Meanwhile my own wireless connections are "open", and therefore unencrypted. There is no technical reason why i can't have an encrypted link that doesn't require the user to enter any password. Such technology exists today (see public key encryption and HTTPS). But does such a standard exist for WiFi? Note: i only want to protect communications, not limit internet access. i get the sense that no such standard exists (since i'm pretty capable with Google), but i'd like it confirmed. Claraification: i want to protect communcations, not limit internet access. That means users are not required to have a password (or its moral equivalent). This means users are not required: to know a password to know a passphrase to enter a CAPTCHA to draw a secret to have a key fob to know a PIN to use a pre-shared key have a pre-shared file to possess a certificate In other words: it has the same accessibility as before, but is now encrypted.

  Read the article

• Connecting to unsecured wireless network

  - by Sanchez

  I would like to know what information is public and can be intercepted in a non-open, but unsecured wireless network. Moreover, is there anything I can do to make it more "secure", other than using https connection whenever possible. In more details, I recently discovered (with surprise) that the wireless network in my school is actually unsecured. Although not everyone can connect to it (you need a student ID), I am told that certain softwares like Wireshark would be able to intercept the data. Since I have been using the network for all private purposes (email, facebook etc), I do feel quite insecure now and would like to understand the situation a bit better. I installed Wireshark and tried to play with it but all I can see are something alien to me. In any case, all I see seems to come directly/indirectly from my IP address, and I have long thought that usually different computers in the same wireless network would be assigned different addresses. Am I wrong? If not, then I feel very confused about what information is actually being captured (potentially by other users in the network, since I don't think I could capture activities of others in the same network anyway), and whether it's safe to use the network at all. (Gambling on others in the same network showing good behaviour is apparently not an option.) Thank you.

  Read the article

• TOR Proxy / Vidalia "New Identity" button not working

  - by Yisman

  I need to hide my ip from time to time. In Vidalia, I click on "New Identity". Ihen I check http://myip.ozymo.com/ to see if my IP address has changed. But, no, it hasn't. Why is that? And how can this be fixed? I tried waiting till the button gets re-enabled to make sure that its done processing the command, but still the IP address is the same. In Fiddler each request is tracked, so it's not a cached response. It's re-requested, but simply does not change. Fiddler though does show one thing interesting. Here is the raw response of many of the requests: HTTP/1.1 200 OK Content-Length: 13 Date: Mon, 23 May 2011 12:02:57 GMT Server: Apache X-Powered-By: PHP/5.2.14 Content-Type: text/html; charset=UTF-8 Age: 1 Connection: keep-alive **Warning: 110 localhost:8118 Object is stale** 26.32.120.106 What is this warning? And is this the cause?

  Read the article

• mod_fcgi produces random 500 Errors

  - by DmitrySemenov

  php 5.4.7 via mod_fcgi when I run the site sometimes it works, sometimes it crashed with 500 Internal Error, this is what I see in error.log everytime I run the script [Mon Sep 24 18:50:43 2012] [warn] [client 68.231.194.198] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Mon Sep 24 18:50:43 2012] [error] [client 68.231.194.198] Premature end of script headers: api.php any ideas? vhost config: <VirtualHost :80> ServerAdmin [email protected] DocumentRoot "/home/www/sites/test.com/html/development" ServerName test.com ServerAlias www.test.com ErrorLog "/home/www/sites/test.com/logs/error_log" CustomLog "/home/www/sites/test.com/logs/access_log" common <IfModule mod_fcgid.c> <Directory /home/www/sites/test.com/html/development> Options +ExecCGI AllowOverride All AddHandler fcgid-script .php FCGIWrapper /home/www/php-fcgi-scripts/php-fcgi-starter .php Order allow,deny Allow from all </Directory> FcgidMaxRequestLen 1073741824 </VirtualHost> fcgi.d conf LoadModule fcgid_module modules/mod_fcgid.so # Use FastCGI to process .fcg .fcgi & .fpl scripts AddHandler fcgid-script fcg fcgi fpl # Sane place to put sockets and shared memory file FcgidIPCDir /var/run/mod_fcgid FcgidProcessTableFile /var/run/mod_fcgid/fcgid_shm IdleTimeout 300 BusyTimeout 300 ProcessLifeTime 7200 IPCConnectTimeout 300 IPCCommTimeout 7200 PHP_Fix_Pathinfo_Enable 1 php-fcgi-starter.php #!/bin/sh PHP_CGI=/usr/local/php547/bin/php-cgi PHP_INI=/etc/php547-fastcgi.ini export PHP_FCGI_TIMEOUT=1200 #export PHP_FCGI_CHILDREN=6 export PHP_FCGI_MAX_REQUESTS=1000 exec $PHP_CGI -c $PHP_INI

  Read the article

• How can I connect my Xbox to my Mac on my network

  - by codecowboy

  I have a wireless router/modem (Router 1) in my living room. This is connected to the internet (cable). Wireless is disabled as the router has a terrible wireless range. My Xbox is connected via ethernet to Router 1. Another LAN output from Router 1 connects to a powerline adapter. Router 1 acts as a DHCP server on 192.168.0.x and has the IP 192.168.0.1 In a second room I have Router 2. This has the powerline feed from Router 1 going into the WAN socket. This router runs the Tomato Firmware and acts as a wireless router for the rest of the house using the IP range 192.168.1.x. Router 2 IP is 192.168.1.1. My Mac is connected to Router 2 using a LAN cable and has the IP 192.168.0.133. Several mobile devices need wireless access. I want an ethernet connection to my Mac, not wireless. I should be able to use software like Connect360 to share media from my Mac to the XBox but the XBox does not see my Mac. I can ping 192.168.0.1 from the Mac. Is this possible using my current setup? If so, how?

  Read the article

• MySql server answer #2002

  - by LOIC

  Since this morning, phpmyadmin is giving me the error message #2002 the server doesn't answer (or the connection to local Mysql is not well configured) and a message about control-use. I'm disappointed it used to work until 2am last night and now the MySQL engine doesn't want to start (told me sometimes about sockets ..) LAMPP is installed on a ubuntu 12.04 lm@Famou:~$ sudo service mysqld status mysqld: unrecognized service    & lm@Famou:~$ sudo service mysqld start mysqld: unrecognized service  : It never works with 'service' !!! and root@Famou:/opt/lampp# /opt/lampp/lampp restart Stopping XAMPP for Linux 1.7.7... XAMPP: Stopping Apache with SSL... XAMPP: XAMPP-MySQL is not running. XAMPP: Stopping ProFTPD... XAMPP stopped. Starting XAMPP for Linux 1.7.7... XAMPP: Starting Apache with SSL (and PHP5)... XAMPP: Starting MySQL... XAMPP: Couldn't start MySQL! XAMPP: Starting ProFTPD... XAMPP for Linux started. is the result of restart lampp

  Read the article

• Browsing \\computer\share fails, but net use \\computer\share works?

  - by JMD

  I've had mixed results with using Windows Explorer to browse remote file shares. The setup: I'm at work on Windows XP SP3 Files are at home on Windows XP SP3 Two separate VPNs are available to access my PC at home corporate OpenVPN (10.1.2.3) a Hamachi/LogMeIn connection (5.1.2.3) With respect to my problem, it doesn't matter which IP I use. They both perform exactly the same way: I expect that if I open Windows Explorer and type in \\10.1.2.3\Shared I should be interrupted with a challenge for credentials, and then be able to interact with the files in the share. However, I just get that annoying dialog, "Windows cannot find '\10.1.2.3\Shared' Check the spelling and try again, or try searching for the item ..." However, I can take that exact same computername/sharename and with net use I can: net use * \\10.1.2.3\Shared * /user:homecomputername\username with this result: Type the password for \\5.69.83.158\C$: Drive Z: is now connected to \\5.69.83.158\C$. The command completed successfully. I can then access the files in Z: in Windows Explorer which was my original intent. Even after Z: is already mapped and the credentials are cached I still cannot bring up \\10.1.2.3\Shared in Windows Explorer. Why does the latter work, but not the former? Edit: Other services work fine, such as RDP. (I have a problem in which I can't SSH home, but I'll consider that separately.)

  Read the article

• configuring lighttpd for large downloads

  - by ahmedre

  i run a web site that hosts pages that are just general scripts (php, etc) and mp3 downloads (some of which are fairly large - up to 200mb). i am running lighttpd on the servers on linux (ubuntu 64). everything is fine, but under high load, the server is not accessible (or very slow - even sshing in takes a while), and i am guessing this is due to a huge number of mp3 downloads at that time. consequently, dns sees the server as down and redirects all the traffic to the other servers, and after a while, it comes back up and things work again. so what's the best way to fix this? ideally, i want the server to continue running (and the web pages - php etc - to always work, but downloads don't always have to work). should i just have 2 web servers running (one for the downloads and one for the php pages), or is it perhaps something i can fix in my lighttpd configuration? here are the snippets from my configuration: server.max-worker = 4 server.max-fds = 2048 server.max-keep-alive-requests = 4 server.max-keep-alive-idle = 4 server.stat-cache-engine = "fam" fastcgi.server = ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 1, "idle-timeout" => 20, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "64", "PHP_FCGI_MAX_REQUESTS" => "1000" ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" )) ) # normal php site $HTTP["host"] =~ "bar.com" { server.document-root = "/usr/local/www/sites/bar.com/" accesslog.filename = "|/usr/sbin/cronolog /var/log/lighttpd/%m/%d/%H/bar.log" } # download site $HTTP["host"] =~ "(download|stream).foo.com" { server.document-root = "/home/audio/" dir-listing.activate = "enable" dir-listing.hide-dotfiles = "enable" evasive.max-conns-per-ip = 1 evasive.silent = "enable" # connection.kbytes-per-second = 256 accesslog.filename = "|/usr/sbin/cronolog /var/log/lighttpd/%m/%d/%H/download.log" }

  Read the article

• Mounting any Windows share from OS X 10.7.5 suddenly stopped working

  - by user2169619

  I have problem with mounting Windows network shares from my OS X 10.7.5 - it worked but it stopped and nothing helps and nothing in logs. Here what I get when trying to mount it manually: mount -t smbfs //10.0.0.7/d /tmp/test When doing sniffing with tshark - no packet it sent through and I get immediately return from the command: mount_smbfs: server connection failed: Unknown error: -1 Nothing in /var/log/syslog.log and /var/log/kern.log. The Finder does not work either - it throws an error that something is wrong (in czech thus I'm not sending the message here). I just cannot connect to any network shares. In virtual Windows 7 in Parallels Desktop I can connect successfully, but not within the network share (so the Win7 is behind OS X NAT) but only with its own IP address. The Windows server share is on the same network segment connected through switch. Any advice how to debug and what can be wrong? I spent hours to find solution on Google and here but no-one with this kind of problem and I do not know how to further debug it since there is no meaningful log / trace etc. I can ping 10.0.0.7 and I can connect to FTP server on 10.0.0.7 - the Windows machine (XP) has firewall completely turned off. The problem is that with tshark, I'm not seeing any packet sending to 10.0.0.7 so it's not even trying to reach the server.

  Read the article

< Previous Page | 600 601 602 603 604 605 606 607 608 609 610 611  | Next Page >