Search Results

Search found 16329 results on 654 pages for 'b long'.

Page 608/654 | < Previous Page | 604 605 606 607 608 609 610 611 612 613 614 615  | Next Page >

  • PC runs very slowly for no apparent reason

    - by GalacticCowboy
    I have a Dell Latitude D820 that I've owned for about 2.5 years. It is a Core 2 Duo T7200 2.0GHz, with 2 GB of RAM, an 80 GB hard drive and an NVidia Quadro 120M video card. The computer was purchased in late November of 2006 with XP Pro, and included a free upgrade to Vista Business. (Vista was available on MSDN but not yet via retail, so the Vista Business upgrades weren't shipped until March of '07.) Since we had an MSDN subscription at the time, I installed Vista Ultimate on it pretty much as soon as I got it. It ran happily until sometime in the spring of 2007 when Media Center (which I had never used except to watch DVDs) started throwing some kind of bizarre SQL (CE?) error. This error would pop up at random times just while using the computer. Furthermore, Media Center would no longer start. I never identified the cause of this error. I had the Vista Business upgrade by this time, so I nuked the machine, installed XP and all the drivers, and then the Vista Business upgrade. Again, it ran happily for a few months and then started behaving badly once again. Vista Business doesn't have Media Center, so this exhibited completely unrelated symptoms. For no apparent reason and at fairly random times, the machine would suddenly appear to freeze up or run very slowly. For example, launching a new application window (any app) might take 30-45 seconds to paint fully. However, Task Manager showed very low CPU load, memory, etc. I tried all the normal stuff (chkdsk, defrag, etc.) and ran several diagnostic programs to try to identify any problems, but none found anything. It eventually reached the point that the computer was all but unusable, so I nuked it again and installed XP. This time I decided to stick with XP instead of going to Vista. However, within the past couple of months it has started to exhibit the same symptoms in XP that I used to see in Vista. The computer is still under Dell warranty until December, but so far they aren't any help unless I can identify a specific problem. A friend (partner in a now-dead business) has an identical machine that was purchased at the same time. His machine exhibits none of these symptoms, which leads me to believe it is a hardware issue, but I can't figure out how to identify it. Any ideas? Utilities? Seen something similar? At this point I can't even identify any pattern to the behavior, but would be willing to run a "stress test"-style app for as long as a couple days if I had any hope that it would find something. EDIT July 17 I'm testing jerryjvl's answer regarding the video card, though I'm not sure it fully explains the symptoms yet. This morning I ran a video stress test. The test itself ran fine, but immediately afterward the PC started acting up again. I left ProcExp open and various system processes were consuming 50-60% of the CPU but with no apparent reason. For example, "services.exe" was eating about 40%, but the sum of its child processes wasn't higher than about 5%. I left it alone for several minutes to settle down, and then it was fine again. I used the "video card stability test" from firestone-group.com. Its output isn't very detailed, but it at least exercises the hardware pretty hard. EDIT July 22 Thanks for your excellent suggestions. Here is an update on what I have tried so far. Ran memtest86, SeaTools (Seagate), Hitachi drive fitness test, video card stability test (mentioned above). The video card test was the only one that seemed to produce any results, though it didn't occur during the actual test. I defragged the drive (again...) with JkDefrag I dropped the video card

    Read the article

  • How to Eliminate Tape Backup and Off-site Storage Service?

    - by Daniel Lucas
    PLEASE READ UPDATE AT THE BOTTOM. THANKS! ;) Environment Info (all Windows): 2 sites 30 servers site #1 (3TB of backup data) 5 servers site #2 (1TB of backup data) MPLS backbone tunnel connecting site #1 and site #2 Current Backup Process: Online Backup (disk-to-disk) Site #1 has a server running Symantec Backup Exec 12.5 with four 1TB USB 2.0 disks. BE jobs for full backups run nightly on all servers in site #1 to these disks. Site #2 backs up to a central file server there using software they already had when we purchased them. A BE job pulls that data nightly to site #1 and stores them on said disks. Off-site Backup (tape) Connected to our backup server is a tape drive. BE backs up the external disks to tape once a week which gets picked up by our off-site storage company. Obviously we rotate two tape libraries, one is always here and one is always there. Requirements: Eliminate the need for tape and off-site storage service by doing disk-to-disk at each site and replicating site #1 to site #2 and vice versa. Software based solution as hardware options have been too pricey (ie, SonicWall, Arkeia). Agents for Exchange, SharePoint, and SQL. Some Ideas So Far: Storage DroboPro at each site with an initial 8TB of storage (these are expandable up to 16TB at present). I like these because they are rackmountable, allow disparate drives, and have iSCSI interfaces. They are relatively cheap too. Software Symantec Backup Exec 12.5 already has all the agents and licenses we need. I'd like to keep using it unless there is a better solution, similarly priced, that does everything BE does plus deduplication and replication. Server Because there is no more need for a SCSI adapter (for tape drive) we are going to virtualize our backup server as it is currently the only physical machine save for SQL boxes. Problems: When replicating between sites we want as little data as possible to go across the pipe. There is no deduplication or compression in what I have laid out here so far. The files being replicated are BE's virtual tape libraries from our disk-to-disk backup. Because of this each of those huge files will go across the wire every week because they change every day. And Finally, the Question: Is there any software out there that does deduplication, or at least compression, to handle just our site-to-site replication? Or, looking at our setup, is there any other solution that I am missing that might be cheaper, faster, better? Thanks. Sorry so long. UPDATE 2: I've set a bounty on this question to get it more attention. I'm looking for software that will handle replication of data between two sites using the least amount of data possible (either compression, deduplication, or some other method). Something similar to rsync would work but it needs to be native to Windows and not a port involving shenanigans to get up and running. Prefer a GUI based product and I don't mind shelling out a few bones if it works. Please, answers that meet the above criteria only. If you don't think one exists or if you think I'm being to restrictive keep it to yourself. If after seven days there is no answer at all, so be it. Thanks again everyone. UPDATE 2: I really appreciate everyone coming forward with suggestions. There is no way for me to try all of these before the bounty expires. For now I'm going to let this bounty run out and whoever has the most votes will get the 100 rep points. Thanks again!

    Read the article

  • Error on installing SVN extension with pecl

    - by thedp
    Hello, I'm trying to install the following PHP extension: http://php.net/manual/en/book.svn.php But when I do pecl install svn-beta I receive an error message that it can't locate the svn_client.h file. I searched the net but couldn't find any useful reference to this error. Thank you for your help. Installation result: root@myUbuntu:/home/thedp# pecl install svn-beta downloading svn-0.5.1.tgz ... Starting to download svn-0.5.1.tgz (23,563 bytes) .....done: 23,563 bytes 4 source files, building running: phpize Configuring for: PHP Api Version: 20041225 Zend Module Api No: 20060613 Zend Extension Api No: 220060519 1. Please provide the prefix of Subversion installation : autodetect 1-1, 'all', 'abort', or Enter to continue: 1. Please provide the prefix of the APR installation used with Subversion : autodetect 1-1, 'all', 'abort', or Enter to continue: building in /var/tmp/pear-build-root/svn-0.5.1 running: /tmp/pear/temp/svn/configure --with-svn --with-svn-apr checking for grep that handles long lines and -e... /bin/grep checking for egrep... /bin/grep -E checking for a sed that does not truncate output... /bin/sed checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ISO C89... none needed checking whether gcc and cc understand -c and -o together... yes checking for system library directory... lib checking if compiler supports -R... no checking if compiler supports -Wl,-rpath,... yes checking build system type... i686-pc-linux-gnu checking host system type... i686-pc-linux-gnu checking target system type... i686-pc-linux-gnu checking for PHP prefix... /usr checking for PHP includes... -I/usr/include/php5 -I/usr/include/php5/main -I/usr/include/php5/TSRM -I/usr/include/php5/Zend -I/usr/include/php5/ext -I/usr/include/php5/ext/date/lib -D_LARGEFILE_SOURCE -D_FILE_OFFSET_BITS=64 checking for PHP extension directory... /usr/lib/php5/20060613+lfs checking for PHP installed headers prefix... /usr/include/php5 checking for re2c... no configure: WARNING: You will need re2c 0.12.0 or later if you want to regenerate PHP parsers. checking for gawk... no checking for nawk... nawk checking if nawk is broken... no checking for svn support... yes, shared checking for specifying the location of apr for svn... yes, shared checking for svn includes... configure: error: failed to find svn_client.h ERROR: `/tmp/pear/temp/svn/configure --with-svn --with-svn-apr' failed

    Read the article

  • Choice of an OS for a home ZFS NAS

    - by OlafM
    I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post.

    Read the article

  • How to delete files and folders that cannot be deleted?

    - by glenneroo
    I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. I ran chkdsk again, this time: chkdsk /f /r. Produced no messages. Same result when deleting. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because these (empty) directories are still not deleteable, C:\1\2\Favorites\Wien\What To Do.. C:\1\2\Favorites\Photography\FIRE Same error as above: Here is what Explorer properties shows for both folders: Update #4 (another partial solution): Using harrymc's answer combined with thoroughly reading through this amazing MS-KB article which contains nearly everyone's idea and then some, inconspicuously titled: You cannot delete a file or a folder on an NTFS file system volume. I was able to delete the 2nd folder C:\1\2\Favorites\Photography\FIRE - the problem being that there was an invisible trailing space at the end. I got lucky when I did an auto-complete whilst playing around with the del "\\?\<path>" command which he suggested. NOTE: A normal del did NOT work, nor did deleting from explorer. Now all that is left is the first directory C:\1\2\Favorites\Wien\What To Do.. (yes I tried endlessly with multiple combinations of the above solution ;) Keep 'em coming! =)

    Read the article

  • how to use ajax with json in ruby on rails

    - by rafik860
    I am implemeting a facebook application in rails using facebooker plugin, therefore it is very important to use this architecture if i want to update multiple DOM in my page. if my code works in a regular rails application it would work in my facebook application. i am trying to use ajax to let the user know that the comment was sent, and update the comments bloc. migration: class CreateComments < ActiveRecord::Migration def self.up create_table :comments do |t| t.string :body t.timestamps end end def self.down drop_table :comments end end controller: class CommentsController < ApplicationController def index @comments=Comment.all end def create @comment=Comment.create(params[:comment]) if request.xhr? @comments=Comment.all render :json=>{:ids_to_update=>[:all_comments,:form_message], :all_comments=>render_to_string(:partial=>"comments" ), :form_message=>"Your comment has been added." } else redirect_to comments_url end end end view: <script> function update_count(str,message_id) { len=str.length; if (len < 200) { $(message_id).innerHTML="<span style='color: green'>"+ (200-len)+" remaining</span>"; } else { $(message_id).innerHTML="<span style='color: red'>"+ "Comment too long. Only 200 characters allowed.</span>"; } } function update_multiple(json) { for( var i=0; i<json["ids_to_update"].length; i++ ) { id=json["ids_to_update"][i]; $(id).innerHTML=json[id]; } } </script> <div id="all_comments" > <%= render :partial=>"comments/comments" %> </div> Talk some trash: <br /> <% remote_form_for Comment.new, :url=>comments_url, :success=>"update_multiple(request)" do |f|%> <%= f.text_area :body, :onchange=>"update_count(this.getValue(),'remaining');" , :onkeyup=>"update_count(this.getValue(),'remaining');" %> <br /> <%= f.submit 'Post'%> <% end %> <p id="remaining" >&nbsp;</p> <p id="form_message" >&nbsp;</p> <br><br> <br> if i try to do alert(json) in the first line of the update_multiple function , i got an [object Object]. if i try to do alert(json["ids_to_update"][0]) in the first line of the update_multiple function , there is no dialog box displayed. however the comment got saved but nothing is updated. it seems like the object sent by rails is nil or cant be parsed by JSON.parse(json). questions: 1.how can javascript and rails know that i am dealing with json objects?deos ROR sent it a object format or a text format?how can it check that the json object has been sent 2.how can i see what is the returned json?do i have to parse it?how? 2.how can i debug this problem? 3.how can i get it to work?

    Read the article

  • Asus P8P67 Rev. 3.1 Motherboard issues powering on and saving settings

    - by Scott
    Edit: New Information Have some updated information from the old question below: So basically my issue right now is somewhat similar, but I've been able to rule out a couple of things. I don't think this has anything to do with light on the motherboard. No matter what lights are on/off on the motherboard when the computer is off, they don't affect this issue. The main power LED on the Mobo is always lit when the power supply is turned on, and that's what matters anyway. Even when the main power LED is on, the PC will NOT boot up the first time I hit the power switch. I have to go reset the power supply (make all lights turn off on the Mobo and back on), and THEN hit the power switch. Then everything boots up. Also, the BIOS settings are reset every time this happens. Asus Tech Support told me to try jumping the power with something metal to try and rule out that it's a problem with the connectors getting power, or if it's a problem with the case power switch pins - haven't done that yet though. Any ideas? This is a lot simpler than it was before when I thought it had to do with certain LED indicators for RAM, EPU, etc. Original Question So I built my new desktop just about 3 weeks ago. I've been having a few issues which I think are all related to my motherboard, an Asus P8P67 Revision 3.1, but I'm not 100% sure as this is really the first from-scratch build I've ever done. I've posted these questions on the Asus forums, Asus Tech Support, and the Corsair forums as well as I thought it might have something to do with my power supply at one point. None of these avenues have solved my issue until now completely, so I thought I'd come here to see what you guys think. Here's what's happening: My computer is off, and I go to power it on. I press the power switch on the case (Antec Nine Hundred), and nothing seems to happen. Upon further inspection, I see that what this actually does is simply turn on the EPU LED on my motherboard, but doesn't actually boot anything up. I then have to go and flip the main power switch on the power supply off and back on. What this does is turn off all lights on the Motherboard after a few seconds, and turn them all back on (including the EPU LED that was off before I hit the power switch the first time). Now, hitting the power switch works. The machine boots up fine, and starts going through the boot up process. As a side note: My Motherboard is set to "Force BIOS", and every single time I change this to do the opposite, the next time my computer boots up that change reverts itself. I think this may be due to the fact that I am doing the hard reset on the power supply each time, but I'm not sure. I had thought that the Motherboard would keep its BIOS settings unless you did something to the Mobo itself - so this may be a related issue, or something else completely. That's basically it. Once it's on, it's on. It works fine, recognizes all of my hardware, and runs great. All fans/lights in the case work great, and I'm getting standard readings. The next time I go to shut the computer down however, I can expect the same exact process getting it up and running, including being forced to go into BIOS and exit again before I can load Windows. Another side note: If I power on my computer using the power switch DIRECTLY after shutting it down, it powers right back on (I think this is because the EPU LED light doesn't have time to turn off). It looks as if as long as the EPU LED is lit up on the motherboard before I hit the power switch on the case, the thing will boot up fine (although this doesn't explain the "Force BIOS" issue, at least it's something). Any ideas? Thanks guys. P.S. - System Specs Asus P8P67 Rev. 3.1 Motherboard Intel Core i7 2600K Processor 16GB (4x4GB) G-Skill 1600 RAM NVIDIA EVGA GTX 570 Video Card Crucial 128GB SSD HD Corsair 850W Power Supply Seagate 2TB HDD

    Read the article

  • Installation of Access Database Engine 32-bit Fails

    - by Rayzor78
    I am trying to install Access Database Engine 2007 32-bit. The splash screen comes up, you click "Next", then it fails with the error: Installation ended prematurely because of an error You click "OK" and another error window says: The installation of the package failed. The exact same situation happens when I try this with Access Database Engine 2010 32-bit. This production server is running Windows Server 2008 R2 SP1 64-bit. Before I tried installing Access Database Engine 32-bit, I first needed to install Microsoft Office 2010 Pro (Excel and Office Tools only). I tried the 32-bit version on the production server since that is how I set it up in our Dev environment. No luck. The 32-bit version would not install. I did NOT get the error "You have 64-bit components of Office installed". I simply received the exact same two errors listed above. So, I knew that 32-bit/64-bit did not really matter for the Office install for my project, so I installed 64-bit of Office Pro 2010 (Excel and Office Tools only) with no problems. I have a requirement that I need to have the 32-bit version of the Access Database Engine installed. 2007 or 2010, doesn't matter. I cannot use the 64-bit version of Access Database Engine 2010 because my SSIS package will not work with it. I require the 32-bit version. I've tried several steps to try to get it installed. I seriously think that the production server has some aversion to installing 32-bit applications. Here's what I've tried: Tried installing via command line with the "/passive" switch....no luck. Tried numerous iterations to copy the install file to the server (downloaded a fresh copy directly to the server, downloaded a fresh copy to my local machine then copied it over, copied it over zipped up) (http://social.msdn.microsoft.com/Forums/en-US/sqldataaccess/thread/efd3c1f0-07cd-45ca-a626-2dd0c7ac3e9f). Tried Method 1 from this link. Could not try Method 2 because it requires a server reboot and in my environment that requires a long change management process. I've verified that I am a local administrator on the server. (Evidence, I am able to install other applications (office 64-bit per above)). Verified that there are no other office products that should be blocking the installation. The fore-mentioned install of Excel 2010 64-bit was the first Office product installed on the server. VERY ODD: To test my theory that the production server does not like 32-bit applications, I installed something lightweight. I installed 7-Zip 32-bit on the production server with no problems whatsoever. Here are some things that I have not tried (i will follow-up once I do): Method 2 (as mentioned above). Requires a server reboot. Have not verified that the Dev and Production environments are 100% identical. I've done a cursory check and on the surface they appear to be the same (same OS and SP version). I need to do a deeper dive to be 100% certain. I had no problems in my Dev environment. In Dev, I installed Office 2010 Pro 64-bit (Excel & Office Tools only) then via command line w/ the "/passive" switch, installed Access Database Engine 2010 32-bit. I don't know what else to try. Any suggestions or comments?

    Read the article

  • what is best config for nginx worker_rlimit_nofile and worker_connections 28672

    - by Binh Nguyen
    i have issue of web-brower response ( especially on ie ) very slow, some time time out, and sometime hang out up to 20 seconds for one file redirect 301 when test with "f12 derverloper tool of ie" .. it report wait/start time very long. but after got connected the elements on web weill be dowload and show out fast ( test at xaluan.com ) It most happen when active user on web more than 2100 ( use google real time live analytic ). server running cenos 5 with ngix, apache, 32core cpu, 96G ram, raid 10 sas hdd.. == flowing is my config == user nobody; # no need for more workers in the proxy mode worker_processes 28; #old 32 #good at 24 error_log /var/log/nginx/error.log; #old add in end: info worker_rlimit_nofile 22528; events { worker_connections 22528; use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 25; #old 5 gzip on; #old on gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; ignore_invalid_headers on; client_header_timeout 1m; #3m client_body_timeout 1m; #3m send_timeout 1m; #3m reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 100M; client_body_buffer_size 256k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; limit_conn_zone $binary_remote_addr zone=limit_per_ip:1m; limit_conn limit_per_ip 20; limit_req_zone $binary_remote_addr zone=allips:5m rate=200r/s; limit_req zone=allips burst=200 nodelay; include "/etc/nginx/vhosts/*"; } =========== I have play around with worker config 1- tried increase as some one suggess: worker_rlimit_nofile = worker_connections = worker_processes * 1024 = 32768 2- tried to set low: worker_processes = 28 and other worker at 22582 and other solution too .. but not work cause some time it make server load hight very quick 3- tried to comment out the # worker_rlimit_nofile . so it will be unlimited. it look like solved a bit about issue response time. but it also make server high load quick in peak time... Please help thanks PS: other apache you may have look for help me out thanks Listen 0.0.0.0:8081 User nobody Group nobody ExtendedStatus On ServerAdmin [email protected] ServerName server.xaluan.com LogLevel warn # These can be set in WHM under 'Apache Global Configuration' Timeout 100 TraceEnable Off ServerSignature Off ServerTokens ProductOnly FileETag None StartServers 15 <IfModule prefork.c> MinSpareServers 20 MaxSpareServers 50 #MaxSpareServers 40 </IfModule> ServerLimit 1572 MaxClients 1572 MaxRequestsPerChild 4000 # MaxRequestsPerChild 3000 KeepAlive On KeepAliveTimeout 3 MaxKeepAliveRequests 300 #MaxKeepAliveRequests 130

    Read the article

  • Windows Service SearchIndexer.exe Crashes on Indexing

    - by Josh Jay
    Relevant Specs: Windows 7 Professional 64-bit SP1 Outlook 2010 Version 14.0.7116.5000 (32-bit) Original Symptom: In outlook, I attempted to search for an email but nothing ever returned and the indicator kept going like it was searching. Attempted Resolutions: I investigated the search options and with some research noticed the Windows Service "Windows Search" (SearchIndexer.exe) was not running. I attempted to start it but I receive this error message: "Windows could not start the Windows Search service on Local Computer. Error 1067: The process terminated unexpectedly." The Event Viewer gives this error entry: Log Name: Application Source: Application Error Date: 6/3/2014 11:02:05 AM Event ID: 1000 Task Category: (100) Level: Error Keywords: Classic User: N/A Computer: ***REMOVED FOR POST*** Description: Faulting application name: SearchIndexer.exe, version: 7.0.7601.17610, time stamp: 0x4dc0d019 Faulting module name: KERNELBASE.dll, version: 6.1.7601.18229, time stamp: 0x51fb1677 Exception code: 0xc0000005 Fault offset: 0x000000000000940d Faulting process id: 0x6a0 Faulting application start time: 0x01cf7f3cc83757c6 Faulting application path: C:\Windows\system32\SearchIndexer.exe Faulting module path: C:\Windows\system32\KERNELBASE.dll Report Id: 06424160-eb30-11e3-9555-843a4b07b336 Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Application Error" /> <EventID Qualifiers="0">1000</EventID> <Level>2</Level> <Task>100</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2014-06-03T15:02:05.000000000Z" /> <EventRecordID>602923</EventRecordID> <Channel>Application</Channel> <Computer>M6700-12011.ncaa.org</Computer> <Security /> </System> <EventData> <Data>SearchIndexer.exe</Data> <Data>7.0.7601.17610</Data> <Data>4dc0d019</Data> <Data>KERNELBASE.dll</Data> <Data>6.1.7601.18229</Data> <Data>51fb1677</Data> <Data>c0000005</Data> <Data>000000000000940d</Data> <Data>6a0</Data> <Data>01cf7f3cc83757c6</Data> <Data>C:\Windows\system32\SearchIndexer.exe</Data> <Data>C:\Windows\system32\KERNELBASE.dll</Data> <Data>06424160-eb30-11e3-9555-843a4b07b336</Data> </EventData> </Event> The regular windows search (from start menu) works fine, and if I reboot the machine the service starts up OK but as soon as it kicks off when I let the machine idle for long enough it crashes (same Event Viewer entry). We also tried the Microsoft Utility to no avail. Has anyone seen this issue before?

    Read the article

  • Windows 7, HTTPS WebDav: Asks for password twice and fails. Any workarounds?

    - by AutoDMC
    Howdy. I have a Dav server running with PHP SabreDav (code.google.com/p/sabredav/wiki/Windows) on Cherokee at an HTTPS secured URL. It's set to use https, and uses Digest Authentication. I can log in with multiple browsers and a few third party clients (BitKinex and Java AnyClient can connect and browse as well, caveats below). However, when attempting to log in with Windows 7 (surprise, surprise), it asks for my password twice, then tells me that my folder is invalid. I have verified that the server is using Digest authentication. I've verified multiple times that third party software can connect. I even went out and bought a GoDaddy SSL certificate so my SSL wouldn't be self signed anymore. I've applied the registry hacks here: support.microsoft.com/kb/943280 (Note that the article says the "fix" already exists for Windows 7, I just need magical registry hax to get it to work) I've applied the registry hacks here: support.microsoft.com/kb/941050 I've applied the registry hacks here: support.microsoft.com/kb/841215 (Supposedly allows Basic Auth, which shouldn't apply, but why not?) All to no avail; Windows continues to ask for my password twice, then state that "The folder you entered does not appear to be valid. Please choose another." Try the command line? Sure: I've attempted to access with NET USE "https://dav.example.com/" password /USER:me (System error 59) I've attempted to access with NET USE "https://dav.example.com/" (System error 1790) I've attempted to access with NET USE "https://dav.example.com/subdir/" password /USER:me (System error 59) I've attempted to access with NET USE "https://dav.example.com/subdir/" (System error 1790) For good luck: ping dav.example.com ... works. And again, web browsers can access the share just fine, so can third party tools. Best I can tell at this point is "HAHA, NO WEBDAV FOR YOU ON WINDOWS 7" which would be fine except everyone who will be using this application... uses Windows 7. And most are not as persistent or pugnacious as I am. I feel like I've burned through every random suggestion I've found anywhere in the first 10 pages of Google on every search term I can think of. Any ideas? I need it to be Webdav, I need it to be over HTTPS, and I really do need a method to access it from Windows 7. EXTRA DETAIL: However, the "third party" programs I've tried have either been buggy, incomplete, or have silly ... "glitches." For example, BitKinex seems to fixate on any http error codes sent, so if there's a glitch reading a directory, BAM, that directory is always listed empty. Long directory listings also show up as blank, even though the transfer panel shows that directory listing is still taking place. In any case, BitKinex is useless for development purposes for the reasons above. And besides, I'm building this for people other than myself, people who will want to get this dav share working "the regular way."

    Read the article

  • What would cause Memcached to Hang for 2+ seconds?

    - by Brad Dwyer
    I'm going nuts trying to scale memcached. From their site: Memcached operations are almost all O(1). Connecting to it and issuing a get or stat command should never lag. If connecting lags, you may be hitting the max connections limit. See ServerMaint for details on stats to monitor. If issuing commands lags, you can have a number of tuning problems. Most common are hardware problems, not enough RAM (swapping), network problems (bandwidth, dropped packets, half-duplex connections). On rare occasion OS bugs or memcached bugs can contribute. Well.. it is most certainly not performing like an O(1) operation for me. Under low to normal load on our site memcached response times for get and set ops are about 0.001 seconds. Not bad. But if we triple the load we get outliers that take 100x (or in rare cases 1000x!) that long. I even had one instance where it took 2.2442 seconds for memcached to store a value. Obviously this is killing our site. Here's the output of Memcached-getStats during one of the slow periods: [pid] => 18079 [uptime] => 8903 [threads] => 4 [time] => 1332795759 [pointer_size] => 32 [rusage_user_seconds] => 26 [rusage_user_microseconds] => 503872 [rusage_system_seconds] => 125 [rusage_system_microseconds] => 477008 [curr_items] => 42099 [total_items] => 422500 [limit_maxbytes] => 943718400 [curr_connections] => 84 [total_connections] => 4946 [connection_structures] => 178 [bytes] => 7259957 [cmd_get] => 1679091 [cmd_set] => 351809 [get_hits] => 1662048 [get_misses] => 17043 [evictions] => 0 [bytes_read] => 109388476 [bytes_written] => 3187646458 [version] => 1.4.13 So things that I have ruled out so far are: Hitting the max connections limit (curr_connections of 84 is well below the default of max of 1024) Swapping - the machine has 900M out of 1024M of memory dedicated to memcached on a dedicated machine. It only appears to be using about 7MB of data as per the bytes stat. How would I diagnose the other hardware problems? prstat doesn't really show a whole lot going on in terms of CPU or memory usage. Not sure how to figure out the network problems but as this is a dedicated server on the same private network as the web box I don't think it's a connectivity issue (ping is less than a millisecond between the boxes). Is there something else I'm missing here? It's driving me nuts. Edit: Also forgot to mention that I've tried both persistent and non-persistent connections with minimal-to-no impact.

    Read the article

  • File Server - Storage configuration: RAID vs LVM vs ZFS something else... ?

    - by privatehuff
    We are a small company that does video editing, among other things, and need a place to keep backup copies of large media files and make it easy to share them. I've got a box set up with Ubuntu Server and 4 x 500 GB drives. They're currently set up with Samba as four shared folders that Mac/Windows workstations can see fine, but I want a better solution. There are two major reasons for this: 500 GB is not really big enough (some projects are larger) It is cumbersome to manage the current setup, because individual hard drives have different amounts of free space and duplicated data (for backup). It is confusing now and that will only get worse once there are multiple servers. ("the project is on sever2 in share4" etc) So, I need a way to combine hard drives in such a way as to avoid complete data loss with the failure of a single drive, and so users see only a single share on each server. I've done linux software RAID5 and had a bad experience with it, but would try it again. LVM looks ok but it seems like no one uses it. ZFS seems interesting but it is relatively "new". What is the most efficient and least risky way to to combine the hdd's that is convenient for my users? Edit: The Goal here is basically to create servers that contain an arbitrary number of hard drives but limit complexity from an end-user perspective. (i.e. they see one "folder" per server) Backing up data is not an issue here, but how each solution responds to hardware failure is a serious concern. That is why I lump RAID, LVM, ZFS, and who-knows-what together. My prior experience with RAID5 was also on an Ubuntu Server box and there was a tricky and unlikely set of circumstances that led to complete data loss. I could avoid that again but was left with a feeling that I was adding an unnecessary additional point of failure to the system. I haven't used RAID10 but we are on commodity hardware and the most data drives per box is pretty much fixed at 6. We've got a lot of 500 GB drives and 1.5 TB is pretty small. (Still an option for at least one server, however) I have no experience with LVM and have read conflicting reports on how it handles drive failure. If a (non-striped) LVM setup could handle a single drive failing and only loose whichever files had a portion stored on that drive (and stored most files on a single drive only) we could even live with that. But as long as I have to learn something totally new, I may as well go all the way to ZFS. Unlike LVM, though, I would also have to change my operating system (?) so that increases the distance between where I am and where I want to be. I used a version of solaris at uni and wouldn't mind it terribly, though. On the other end on the IT spectrum, I think I may also explore FreeNAS and/or Openfiler, but that doesn't really solve the how-to-combine-drives issue.

    Read the article

  • How to use Public IP in case of two ISP when two differs from each other

    - by user1471995
    Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

    Read the article

  • What seems to be plaguing my hard drives?

    - by Craig
    In a little bit of a tech nightmare here. I know oodles about software, not so much more than the above average user about hardware. I recently had to toss an old desktop of mine. It was gradually getting slower and slower, and after shutting the desktop down for long periods of time, it would choke up upon startup. Sometimes it'd give a disk read error, sometimes say no OS was found, etc. Restarting it about 5-15 times would eventually boot properly. Weird. I also noticed that startup programs were going missing, Dropbox was reindexing my entire folder, and Backblaze was backing up less than the number of files that it should. This lead me to believe it was probably a hard drive issue. I began to wonder why I'd have hard drive issues, and came to closure when I assumed it was because of recent power surges and outages. I'm sure that does a number on the drive. I bought a new desktop recently. It's not a beast or anything, but it's enough for what I do. It's an eMachines (I know, I know) Ultra-Slim (http://www.amazon.com/eMachines-Ultra-Slim-ER1401-57-Desktop-PC/dp/B00475OG9U). This is ideal for me because it's small and portable. It comes with an AC adapter and battery, like a laptop. Just to be safe, I bought an uninterruptable power supply on top of that. It's basically protected completely from any outages that might scramble the drive. I set this up a few days ago and for the past few days I've been perfecting settings, downloading the usual applications, etc. Two days ago, I noticed Dropbox was reindexing my entire Dropbox folder. I installed both Dropbox and Backblaze on this system, but it is very much more lightweight than the other. Only about 15 third-party applications installed. I thought that maybe Dropbox and Backblaze were stressing my system, so I turned off Backblaze. Still, Dropbox runs and comes across this infinite reindex issue. I noticed that upon a reboot recently, two applications did not start on startup either. Also, much like my old desktop, every 3rd or 4th reboot, I'll be forced into a chkdsk. This makes me incredibly nervous. What could possibly be going wrong with my old, years-old desktop that is immediately causing the same issues to my new one? I've considered all of the basics. I'm in a very air conditioned room. I take run routine virus scans. I'd like to think I take care of my systems very well. What is this issue that is haunting me? There's always the possibility that this new desktop has a junk hard drive, but it just seems way too coincidental.

    Read the article

  • How can I recover an ext4 filesystem corrupted after a fsck?

    - by Regan
    I have an ext4 filesystem on luks over software raid5. The filesystem was operating "just fine" for several years when I was beginning to run out of space. I had a 9T volume on 6x2T drives. I began upgrading to 3T drives by doing the mdadm fail, remove, add, rebuild, repeat process until I had a larger array. I then grew the luks container, and then when I unmounted and tried to resize2fs I was given the message the filesystem was dirty and needed e2fsck. Without thinking I just did e2fsck -y /dev/mapper/candybox and it began spewing all kinds of inode being removed type messages (can't remember exactly) I killed e2fsck and tried to remount the filesystem to backup data I was concerned about. When trying to mount at this point I get: # mount /dev/mapper/candybox /candybox mount: wrong fs type, bad option, bad superblock on /dev/mapper/candybox, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Looking back at my older logs I noticed the filesystem was giving this error each time the machine booted: kernel: [79137.275531] EXT4-fs (dm-2): warning: mounting fs with errors, running e2fsck is recommended So shame on me for not paying attention :( I then tried to mount using every backup superblock (one after another) and each attempt left this in my log: EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 0 failed (26534!=65440) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 1 failed (38021!=36729) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 2 failed (18336!=39845) ... EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 11911 failed (28743!=44098) BUG: soft lockup - CPU#0 stuck for 23s! [mount:2939] Attempts to restart e2fsck results in: # e2fsck /dev/mapper/candybox e2fsck 1.41.14 (22-Dec-2010) e2fsck: Group descriptors look bad... trying backup blocks... candy: recovering journal e2fsck: unable to set superblock flags on candy At this point, I decided it best to order some more drives and make an image using ddrescue Now two weeks later I have an image of the luks partition in a .img file. # ls -lh total 14T -rw-r--r-- 1 root root 14T Oct 25 01:57 candybox.img -rw-r--r-- 1 root root 271 Oct 20 14:32 candybox.logfile After numerous attempts using everything I could find online I could not coerce e2fsck to do anything on the image, so I used mkfs.ext4 -L candy candybox.img -m 0 -S and I was able to mount the dirty filesystem readonly without the journal and recover 960G of data. It gave all kinds of errors of various directories not existing and so forth but I was able to get some stuff. Which gave me some hope! I then ran e2fsck again and it had to recreate the root inode and gave a massive list of correcting group counts, I accepted the root inode creation and said no to everything else, leaving a completely empty filesystem. Re-ran again and said yes to all questions with the same result but now a "clean" but empty filesystem. extundelete gives me 0 recoverable inodes found. And now I'm stuck again, I can't come up with any other methods other than dropping to something like photorec which will give me an absolute mess with how large the filesystem was. I'm willing to re-copy the image from the original array and start over, if I can get any suggestions or ideas on a way to get more of my files back. I wish I could give more detailed logs of the commands that have run, but the output is long scrolled passed except for what gets logged to syslog and my memory is not as detailed due to the timeframe this has occurred over. Any help is greatly appreciated!

    Read the article

  • Choice of an OS for a home ZFS NAS

    - by OlafM
    I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post. UPDATES Given the first answers, I will strongly suggest the person paying the hardware to insert a second HD. Better 2x2TB than 1x3TB (3 TB is oversized anyway). I was trying to keep the initial costs down to spread them over a longer period, but better having something good from the beginning.

    Read the article

  • Windows 8.1 Update 1 Disk Usage 100%

    - by Gookjin Jeong
    Background Information / Computer Specs I have a 14-inch Samsung Series 5 Ultra. Core i5 CPU, 750GB HDD, 8GB RAM, Intel HD Graphics 4000. I've had the computer for about 1.5 years with no major problems. Problem The issue appeared at the beginning of April this year, when I updated the OS to Windows 8.1 Update 1 (not from 8 to 8.1). After being on continually (except for at night, when I put it on sleep mode) for about 48 hours, the disk usage as seen by Task Manager hits 100%. When this happens, everything from opening/closing applications to typing and even bringing up the start screen by pressing the Windows key becomes extremely slow. The only way to make the disk usage decrease is to restart the computer. Then the problem repeats. I've used my current laptop (as well as my previous laptops) this way -- putting it on sleep mode at night and restarting it only when Windows needs to install updates -- for a long time. So I know the 100% disk usage is not due to the way I use the computer. The thing that causes the spike varies. Sometimes it's System, sometimes it's one of the various applications I installed (e.g. Chrome, Evernote, Spotify, Wunderlist, iTunes, etc.), and sometimes it's Antimalware Service Executable, etc. Tried Solutions I think I tried almost every solution out there for this problem: Running the check disk command (chkdsk /b /f /v /scan c:) from Admin Command Prompt Running Windows Memory Diagnostic Disabling Superfetch and Windows Search from services.msc Running "Fix problems with Windows Update" from Control Panel -- Troubleshooting Updating and rolling back the graphics driver (Intel HD 4000) Disabling "Use hardware acceleration when available" from Chrome settings Disabling Intel Rapid Storage Technology Running the SFC /SCANNOW command as recommended here Running a quick scan & a full scan from Windows Defender (no threats found) Taking the hard drive out and putting it back Refreshing the computer, from the Update and recovery -- Recovery option in Windows settings NONE of the above worked for me. I was about to give up but then noticed that one of the main culprits of the disk usage spike, as shown in the "Disk Activity" section of the Resource Monitor, was C:\System (pagefile.sys). I googled around and found that one of the recommended solutions was to disable pagefile. I then went to **Control Panel -- System and Security -- System -- Advanced system settings -- Advanced tab -- Performance settings -- Advanced tab -- "Change" under Virtual memory and discovered that the number for "Currently allocated" at the bottom was 1280MB, although the number for "Recommended" was 4533MB. I immediately changed it to 4533MB and checked my family members' computers to see what the numbers were like. All of theirs had a currently allocated space that was only slightly smaller than the recommended space. See screenshot below: This might fix the problem. I'll have to wait a couple more days.But if it doesn't, what in the world should I do next? I'm guessing the hard drive isn't failing because This computer is less than 2 years old; and Speccy says that the status of the HDD is good. Update 5/27/2014 The "4533MB" solution did not work. I had to reboot the computer about 30 minutes ago because the disk usage again hit 100%. When I opened Resource Monitor the C:\System (pagefile.sys) again was shown to be the culprit. I have now disabled pagefile entirely via the same window shown above in the screenshot. The number for "currently allocated" is now 0MB. Will update again in a couple days, or if the problem occurs again, whichever comes sooner.

    Read the article

  • My 2009 MacBook Logic board failed - options to proceed and how difficult?

    - by user181061
    Scannerz just gave my MacBook logic board a big fat F! I upgraded from Snow Leopard to Mountain Lion about 3 weeks ago. The system was running short of memory so I upgraded it. The system was running fine for about 2 weeks. Yesterday the thing started acting erratic. A lot of spinning beach balls, delays, and then some errors saying files couldn't be read to or from the drive. I figured the drive was going because the system is over 3 years old. I ran Scannerz on it and it indicated a lot of errors and irregularities. I rescanned it in cursory mode, and none of them were repeatable, just showing up all over the place in different regions of the scan. I went through the docs and they implied either an I/O cable was bad, a connection was damaged, or the logic board was bad. I tossed on my backup of Snow Leopard that I cloned from the original hard drive because I figured Mountain Lion was to blame and booted from the USB drive with the clone on it. It wasn't. I performed scans on every single port, and errors and irregularities that couldn't be repeated were showing up on every single one of them. I then, for kicks, put a CD into the CD player. Scannerz doesn't test optical drives but I figured surely that will work. No it won't. More spinning beach balls and messages telling me it can't be read. It was working fine 3 days ago. I know a lot of people don't like MacBook's, but mine's been great, at least until now. It was working great even with Mountain Lion after the upgrade. The system is a mid-2009 MacBook. In my opinion, it's a complete waste to toss this system. The display is too good, the keyboard works great, and it still looks good, plus this type of MacBook still uses the FireWire 400 port and I use that for Time Machine backups. I've tried reseating the RAM, it didn't do anything. I shut the system down and put in the old RAM, booted to Snow Leopard, and the problems persist. Here are my questions: The Scannerz documentation somewhere said something about the Airport card not being seated properly, but when I go to iFixit, it's apparent, at least I think it's apparent, that this isn't a slot type Airport card that the user can easily install or remove. If the cables or connections to the Airport card are bad, could they be causing this problem. How about any other connections that can be intermittent, failing or erratic? Any type of resets that I could possibly do to get rid of this? For any of those that have replaced a logic board on a MacBook, if this really is the culprit, are there any "gotcha's" I need to be aware of? As an FYI, I replaced the hard drive on an old iBook @500MHz that I had a long time ago, and I replaced the drive on a 1.33GHz PowerBook about 6 years ago. You have to be careful, but using some of the info on web sites like iFixit it's not that hard. Time consuming, but not that hard. The Intel based MacBook's to me look like they're easier to service than either of those. I'm thinking about getting a unit off of eBay that matches mine but has something else wrong with it, like a busted display. I REFUSE to buy a new system. A guy at my office has a 2007 Mac Pro and he can't upgrade to Mountain Lion because his system is "obsoleted." That's ridiculous. If you pay nearly $7,500 for a system it shouldn't be trash just because Apple decides they don't have enough money (sorry for the soap box, but it's true, IMO!) Any input is appreciated.

    Read the article

  • Distributed and/or Parallel SSIS processing

    - by Jeff
    Background: Our company hosts SaaS DSS applications, where clients provide us data Daily and/or Weekly, which we process & merge into their existing database. During business hours, load in the servers are pretty minimal as it's mostly users running simple pre-defined queries via the website, or running drill-through reports that mostly hit the SSAS OLAP cube. I manage the IT Operations Team, and so far this has presented an interesting "scaling" issue for us. For our daily-refreshed clients, the server is only "busy" for about 4-6 hrs at night. For our weekly-refresh clients, the server is only "busy" for maybe 8-10 hrs per week! We've done our best to use some simple methods of distributing the load by spreading the daily clients evenly among the servers such that we're not trying to process daily clients back-to-back over night. But long-term this scaling strategy creates two notable issues. First, it's going to consume a pretty immense amount of hardware that sits idle for large periods of time. Second, it takes significant Production Support over-head to basically "schedule" the ETL such that they don't over-lap, and move clients/schedules around if they out-grow the resources on a particular server or allocated time-slot. As the title would imply, one option we've tried is running multiple SSIS packages in parallel, but in most cases this has yielded VERY inconsistent results. The most common failures are DTExec, SQL, and SSAS fighting for physical memory and throwing out-of-memory errors, and ETLs running 3,4,5x longer than expected. So from my practical experience thus far, it seems like running multiple ETL packages on the same hardware isn't a good idea, but I can't be the first person that doesn't want to scale multiple ETLs around manual scheduling, and sequential processing. One option we've considered is virtualizing the servers, which obviously doesn't give you any additional resources, but moves the resource contention onto the hypervisor, which (from my experience) seems to manage simultaneous CPU/RAM/Disk I/O a little more gracefully than letting DTExec, SQL, and SSAS battle it out within Windows. Question to the forum: So my question to the forum is, are we missing something obvious here? Are there tools out there that can help manage running multiple SSIS packages on the same hardware? Would it be more "efficient" in terms of parallel execution if instead of running DTExec, SQL, and SSAS same machine (with every machine running that configuration), we run in pairs of three machines with SSIS running on one machine, SQL on another, and SSAS on a third? Obviously that would only make sense if we could process more than the three ETL we were able to process on the machine independently. Another option we've considered is completely re-architecting our SSIS package to have one "master" package for all clients that attempts to intelligently chose a server based off how "busy" it already is in terms of CPU/Memory/Disk utilization, but that would be a herculean effort, and seems like we're trying to reinvent something that you would think someone would sell (although I haven't had any luck finding it). So in summary, are we missing an obvious solution for this, and does anyone know if any tools (for free or for purchase, doesn't matter) that facilitate running multiple SSIS ETL packages in parallel and on multiple servers? (What I would call a "queue & node based" system, but that's not an official term). Ultimately VMWare's Distributed Resource Scheduler addresses this as you simply run a consistent number of clients per VM that you know will never conflict scheduleing-wise, then leave it up to VMWare to move the VMs around to balance out hardware usage. I'm definitely not against using VMWare to do this, but since we're a 100% Microsoft app stack, it seems like -someone- out there would have solved this problem at the application layer instead of the hypervisor layer by checking on resource utilization at the OS, SQL, SSAS levels. I'm open to ANY discussion on this, and remember no suggestion is too crazy or radical! :-) Right now, VMWare is the only option we've found to get away from "manually" balancing our resources, so any suggestions that leave us on a pure Microsoft stack would be great. Thanks guys, Jeff

    Read the article

  • Gaming blew fuse and causes funny smell: how to overcome?

    - by George Tomlinson
    I've been gaming for a while now. When playing certain games this PC goes into overdrive. The fan/fans start/s to sound like a jet engine it/they get/s so busy. Also I have smelt burning when this has happened. The fuse blew on the 4 socket adapter I was using recently. On the following thread someone said this could be due to the PSU not being strong enough to handle the load, in what it seems could be a related issue someone had, although the person who posted this question did say that blowing a fan on their PC stopped it crashing in that case: http://www.tomshardware.co.uk/answers/id-2047543/gtx-650-overheating-issue.html. This is exactly what they said: Your GPU isn't overheating. 70+ before it would shutdown and cause a restart. Make sure your PSU is strong enough to handle your new system at load and possibly run Memtest to check your RAM (although not BSOD'ing and just shutting down points to the PSU). This (the PSU part) makes more sense to me than it being to do with dust etc, since it seems a more plausible explanation of why the fuse blew. The PC has no problems except when playing certain games: i.e. TERA Rising and WoW with add-ons (I think WoW is ok as long as I don't have more than 1 add-on (Healers Have To Die)). I'm just wondering if anyone knows or can suggest what I might be able to do to be able to play these games without this problem occurring. The PC's spec is this: Display: NVIDIA GeForce GTX 650 8GB RAM (6 available) Processor: AMD FX (tm) - 8120 Eight-Core Processor - 3.1 GHz, 4 Cores, 8 Logical Processors I have read on another post that forcing vsync in the Nvidia Control Panel helped with what seems could be a similar problem, so I plan to see if that solves it, God permitting. EDIT: I tried the Vsync thing, and it seems the situation may have improved, although this may be due to something else: i.e. maybe the PC was working harder yesterday, due to just having downloaded a few things or lots of things running. I'm still noticing the funny smell when playing TERA. It's not so much burning: it's more like glue. The smell might have had a burning element to it in the past, but I think it's always had a glue element. EDIT 2: the PSU is an 'ATX Switching Power Supply', Model E-500ATX. Other info it gives on the PSU is 230V, Current 10A and Frequency 50-60Hz. It also has some other info which I can supply if necessary. Putting the PC plug in the wall socket instead of the power strip seems like it might have reduced the load on the PC quite a bit: I think it sounds less stressed. it has been off for a while whilst I took the side panel off though, so I'll wait to see what happens before getting too excited. EDIT 3: hmm. So here's the latest: just playing TERA. The fan's running quite fast again. Hard to tell whether switching to the wall socket has made a difference in terms of strain on the PC: I don't know if one would expect it to. Still seems like it might have helped though. Oh and there didn't seem to be much dust in the PC, although I didn't disconnect any components. I'm still getting the glue type smell. ASIDE: reminds me of someone on a PC near me at the library once who was actually sniffing glue right there in front of everyone while on the PC and he started talking about how he was sniffing glue. lol. That's no joke. EDIT 4: So the questions now are: Question 1: Is the smell something I should sort out? (If so, how might I do this?) Question 2: is it necessary to take any steps to prevent blowing another fuse (and if so which step/s?).

    Read the article

  • Windows 7 is stuck at "Starting Windows" when I attempt to boot computer

    - by Eli
    Basically, whenever I turn on my computer, it gets to the Starting Windows phase and just stays there. The startup animation still plays, yet it gets nowhere. I have tried booting into safe mode, however it gets stuck at loading CLASSPNP.SYS. It then freezes there and doesn't continue booting. I have tried booting into recovery mode from the hard drive, and it freezes after displaying the background image. I have tried booting from a recovery CD, which works, and I was able to use system restore. However, using system restore did not fix it, and it still is stuck at the Starting Windows screen. I have tried booting a Windows CD (Windows 8 Retail Installer) to see if I could upgrade it to fix this issue, however that froze at a blank screen after it got past the boot logo. I have tried changing around the BIOS settings (including resetting), to no avail. I have tried re-plugging the internal PSU cables (this is a custom-built desktop), yet this has changed nothing. I can boot into a loopback Ubuntu install on the same drive, which works fine, other than the fact that it has issues with some of the USB ports and the network card. This system has worked fine for the past few months, completely stable, and nothing in the configuration has changed before this error started happening. Startup Repair on the Windows recovery CD doesn't find any issues. Unplugging my secondary hard drive or swapping around memory doesn't change anything. The hard drive itself is fine, it hasn't shown any signs of failure and once again, boots my other OS fine. If anyone could help with this, that would be great. I can't seem to find any possible solution to this. If it makes any difference, my system specs are as follows: AMD FX-8320 Gigabyte GA-970A-D3 4GB of DDR3 Radeon HD 6870 550w PSU I'd like to not have to reinstall Windows, for I have more than a terabyte of data that I would have to back up if that becomes the only option. EDIT: I have since tried the following: Tried the solution involving restoring files from RegBackup, which changed nothing. Tried testing everything with Hiren's boot CD, everything comes back as fine. Tried disabling everything unnecessary in the BIOS and unplugging everything unneeded, it still hangs. Tried swapping out every possible combination of RAM, it still has the same result. The RAM is not at fault it seems Tried every GPU I own (which is many!) and it still hangs at the exact same place. Tried minimizing the power consumption as much as possible, even using an old PCI graphics card. It still hangs at the same place in the same way, signifying that it's not the PSU at fault. Tried resetting the BIOS again, still nothing. Tried every possible combination of BIOS options, even downclocking everything, it still hangs in the same spot. Tried upgrading the BIOS from version FB to FD, which changed nothing. Based on this, I would conclude the motherboard to be at fault. Are there any other possibilities? I don't want to spend $150 for a new motherboard. EDIT 2: This is what it gets stuck at when I try to boot into safe mode: Note the slight graphical corruption at the top of the screen. No matter how I set up the system, this seems to be there. In addition, either it has stopped booting into safe mode now, or it takes upwards of 2+ hours, and I haven't left it running for that long.

    Read the article

  • How to install Delorme StreetAtlas (any version) + GPS inside VirtualBox VM?

    - by hotei
    When I try to run the install program I get a popup message that says the installer program is not a valid executable. Background: I want a GPS with maps on my laptop running Ubuntu 10.4LTS. Unfortunately I can't find a decent native Linux GPS solution with 50 state US street level coverage. I have VirtualBox VMs available for WinXP and Win7 (among others). The VMs work fine with MicroSoft Streets and Trips (2010) and MapNGo 5 (a very! old Delorme product), but while both these products support GPS, they don't support the Earthmate LT-40 USB GPS I already have. I've got pretty much every Delorme Street Atlas they've released in the last decade and none of them will install in a VM. Any help would be much appreciated. Clarification: I've installed the Delorme products from these CDs before and the disks are fine - as long as installation is done on a "physical" machine. Added: I've tried install from an iso as well as the real CD. No difference in result (setup.exe is not a valid executable) The WinXP is SP-2 (held back on purpose at this point - I'll snapshot and fork a later SP to test). The Win2K is SP-6a. Win7(32) VM is whatever updates came out last week. The USB setup is working at least to the point where the GPS device is active in the device list (has an x in the box). At this point its not relevant because the program that needs to read it can't even be installed. Added 9-19: Added wine as harrymc suggested. Initial result was no change. Here's wines error message. The file '/media/Disk1/setup.exe' is not marked as executable. If this was downloaded or copied form an untrusted source, it may be dangerous to run. For more details, read about the executable bit. At first I thought the execute bit was the problem, but looking at several other windows CDs I see that the execute bit is not set on their exe files (which install to VM without error). Still it was worth a shot so I copied the StreetAtlas 9 DVD to my hard disk, changed the on-disk exe files to have the execute bit set and tried to install again. This time the install via wine got me through the installation process. When I start the program it bombs immediately, so we haven't made much real progress so far. I very much prefer the VM solution to wine, so I'm going back to that for now. To recap the VM situation, using an updated XP with SP3 and all recommended hotfixes: StreetAtlas 2009 USA fails with "not marked as executable". StreetAtlas 2007 USA fails with "not marked as executable". StreetAtlas 9 (copyright 2001) fails with "not marked as executable". SteeetAtlas (copyright 1991) fails with "not marked as executable" Delorme Topo 4 (copyright 2002) fails with "not marked as executable". Just about ready to give up. So I switched from XP VM to Win7 VM and tried StreetAtlas 2009 again. This time it installs. Earthmate USB GPS works. WTH? I feel like the monkey who just wrote a line of Shakespear. I'm smiling because it worked, but I have no clue why. I'm awarding the bounty to harrymc because wine did give some useful insight into the problem and a +1 to goyiux as thanks for helping.

    Read the article

  • mySQL Optimization Suggestions

    - by Brian Schroeter
    I'm trying to optimize our mySQL configuration for our large Magento website. The reason I believe that mySQL needs to be configured further is because New Relic has shown that our SELECT queries are taking a long time (20,000+ ms) in some categories. I ran MySQLTuner 1.3.0 and got the following results... (Disclaimer: I restarted mySQL earlier after tweaking some settings, and so the results here may not be 100% accurate): >> MySQLTuner 1.3.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering [OK] Currently running supported MySQL version 5.5.37-35.0 [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +ARCHIVE +BLACKHOLE +CSV -FEDERATED +InnoDB +MRG_MYISAM [--] Data in MyISAM tables: 7G (Tables: 332) [--] Data in InnoDB tables: 213G (Tables: 8714) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [--] Data in MEMORY tables: 0B (Tables: 353) [!!] Total fragmented tables: 5492 -------- Security Recommendations ------------------------------------------- [!!] User '@host5.server1.autopartsnetwork.com' has no password set. [!!] User '@localhost' has no password set. [!!] User 'root@%' has no password set. -------- Performance Metrics ------------------------------------------------- [--] Up for: 5h 3m 4s (5M q [317.443 qps], 42K conn, TX: 18B, RX: 2B) [--] Reads / Writes: 95% / 5% [--] Total buffers: 35.5G global + 184.5M per thread (1024 max threads) [!!] Maximum possible memory usage: 220.0G (174% of installed RAM) [OK] Slow queries: 0% (6K/5M) [OK] Highest usage of available connections: 5% (61/1024) [OK] Key buffer size / total MyISAM indexes: 512.0M/3.1G [OK] Key buffer hit rate: 100.0% (102M cached / 45K reads) [OK] Query cache efficiency: 66.9% (3M cached / 5M selects) [!!] Query cache prunes per day: 3486361 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 812K sorts) [!!] Joins performed without indexes: 1328 [OK] Temporary tables created on disk: 11% (126K on disk / 1M total) [OK] Thread cache hit rate: 99% (61 created / 42K connections) [!!] Table cache hit rate: 19% (9K open / 49K opened) [OK] Open file limit used: 2% (712/25K) [OK] Table locks acquired immediately: 100% (5M immediate / 5M locks) [!!] InnoDB buffer pool / data size: 32.0G/213.4G [OK] InnoDB log waits: 0 -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Reduce your overall MySQL memory footprint for system stability Enable the slow query log to troubleshoot bad queries Increasing the query_cache size over 128M may reduce performance Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Read this before increasing table_cache over 64: http://bit.ly/1mi7c4C Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 512M) [see warning above] join_buffer_size (> 128.0M, or always use indexes with joins) table_cache (> 12288) innodb_buffer_pool_size (>= 213G) My my.cnf configuration is as follows... [client] port = 3306 [mysqld_safe] nice = 0 [mysqld] tmpdir = /var/lib/mysql/tmp user = mysql port = 3306 skip-external-locking character-set-server = utf8 collation-server = utf8_general_ci event_scheduler = 0 key_buffer = 512M max_allowed_packet = 64M thread_stack = 512K thread_cache_size = 512 sort_buffer_size = 24M read_buffer_size = 8M read_rnd_buffer_size = 24M join_buffer_size = 128M # for some nightly processes client sessions set the join buffer to 8 GB auto-increment-increment = 1 auto-increment-offset = 1 myisam-recover = BACKUP max_connections = 1024 # max connect errors artificially high to support behaviors of NetScaler monitors max_connect_errors = 999999 concurrent_insert = 2 connect_timeout = 5 wait_timeout = 180 net_read_timeout = 120 net_write_timeout = 120 back_log = 128 # this table_open_cache might be too low because of MySQL bugs #16244691 and #65384) table_open_cache = 12288 tmp_table_size = 512M max_heap_table_size = 512M bulk_insert_buffer_size = 512M open-files-limit = 8192 open-files = 1024 query_cache_type = 1 # large query limit supports SOAP and REST API integrations query_cache_limit = 4M # larger than 512 MB query cache size is problematic; this is typically ~60% full query_cache_size = 512M # set to true on read slaves read_only = false slow_query_log_file = /var/log/mysql/slow.log slow_query_log = 0 long_query_time = 0.2 expire_logs_days = 10 max_binlog_size = 1024M binlog_cache_size = 32K sync_binlog = 0 # SSD RAID10 technically has a write capacity of 10000 IOPS innodb_io_capacity = 400 innodb_file_per_table innodb_table_locks = true innodb_lock_wait_timeout = 30 # These servers have 80 CPU threads; match 1:1 innodb_thread_concurrency = 48 innodb_commit_concurrency = 2 innodb_support_xa = true innodb_buffer_pool_size = 32G innodb_file_per_table innodb_flush_log_at_trx_commit = 1 innodb_log_buffer_size = 2G skip-federated [mysqldump] quick quote-names single-transaction max_allowed_packet = 64M I have a monster of a server here to power our site because our catalog is very large (300,000 simple SKUs), and I'm just wondering if I'm missing anything that I can configure further. :-) Thanks!

    Read the article

  • How to save a ntfs partition which suddenly became empty

    - by SteveO
    One ntfs partition of my laptop was suddenly wiped out without any notice to me, when I rebooted from Windows 7 to Ubuntu 12.04 today. I am in need of help to save my files on that partition, which are important and unfortunately haven't been backed up yet. My laptop has two operating systems: Windows 7 and Ubuntu 12.04. with a ntfs partition shared between the two operating systems for storing some data files (109GB, about 97%of which has been used). I have almost always been using Ubuntu, but today I happened to have to work under Windows. Following is a record of what happened in the time order, numbering according to which operating system I was in at each stage. When I started into Windows 7, right before being able to log in, it took a while and two reboots to configure the Windows. I thought it was normal, since last time when I was using Windows two weeks ago, it took very long and several reboots to update Windows, since the last time I used Windows before then was in November last year. Then after finally being able to log in Windows 7, I installed Libre Office, MathType (I got it from http://dl.portablesoft.org/down/?id=2515, which I originally thought was a trial version, but later I learned was a cracked version and felt wrong. I made a copy of it at dropbox http://dl.dropbox.com/u/13029929/MathType_6.8_PortableSoft.rar, not for distributing it but to list it there just in case it will help to identify the problem), and MikTex. I then edited some .doc files in the ntfs partition under both Microsoft Office with MathType, and Libre Office. When I finished working under Windows and rebooted into Ubuntu, Ubuntu did some filesystem checking and reported that the ntfs partition was not able to be mounted. Then I rebooted again into Windows, and found that the ntfs partition had been emptied, i.e. all the data files were gone, and only one system file bootsqm.dat and one system directory System Volume Information were there, with their last updated time being the time when I first rebooted from Windows to Ubuntu (in fact, it is 4 hours in advanced than the actual time of that rebooting , see immediately below) Also I noticed that the time shown by Windows is not correct for my time zone (UTC-05:00) Eastern Time (US & Canada)), which is 4 hours in advance than the correct time (my current time is 3am, but the computer shows 7am). Same things happened when I rebooted into Ubuntu again: the ntfs has been emptied and left with only one Windows system file bootsqm.dat and one Windows system directory System Volume Information. the time shown by Ubuntu is 4 hours in advance than the correct time. I wonder what I can do to retrieve my data files back on the ntfs partition? If I am not able to do it myself, will some professionals be able to help me out? Thanks a lot! PS: I didn't think I did any thing that required emptying that partition. But there were quite some works I did during that stage right before the reboot from Windows to Ubuntu when the problem occured. Did I make any mis-operation?

    Read the article

< Previous Page | 604 605 606 607 608 609 610 611 612 613 614 615  | Next Page >