Search Results

Search found 12213 results on 489 pages for 'mapped drive'.

Page 61/489 | < Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >

• Is a disk/ata timeout exception dangerous?

  - by j-g-faustus

  I have a few hard drives in mdadm RAID 5 configured to go to standby after a few minutes of inactivity. (Using hdparm.conf spindown_time.) At irregular intervals I get messages like these in dmesg: [ 1840.251661] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1840.251722] ata4.00: failed command: SMART [ 1840.251758] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [ 1840.251759] res 40/00:14:50:2e:04/00:00:02:00:00/40 Emask 0x4 (timeout) [ 1840.251858] ata4.00: status: { DRDY } [ 1840.251888] ata4: hard resetting link [ 1840.600742] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1840.601521] ata4.00: configured for UDMA/133 [ 1840.601547] ata4: EH complete [337877.713988] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [337877.714019] ata4.00: failed command: SMART [337877.714038] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [337877.714039] res 40/00:04:90:10:81/00:00:00:00:00/40 Emask 0x4 (timeout) [337877.714089] ata4.00: status: { DRDY } [337877.714107] ata4: hard resetting link [337878.063085] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [337878.063743] ata4.00: configured for UDMA/133 [337878.063764] ata4: EH complete I think the exception is caused by smartd when a drive does not wake up quickly enough. There are no issues (that I can tell) in accessing the drives normally through the file system - it takes a few seconds longer than normal when they are asleep, but there are no exceptions. Is this something I should worry about, as a potential symptom on something that could corrupt a drive over time? Or can I safely ignore it as part of normal operation? Edit: By request: smartctl -a for sdaand sde, both disks are members of the array. If ata4is the same as scsi-4 then sde is the one that gave the error above, according to /dev/disk/by-path.

  Read the article

• How can I set up FakeRAID/SoftRAID using mdadm without losing data?

  - by Danatela

  There is RAID0 of 2 drives connected through Silicon Image 3132 SATA SoftRAID controller. Under Windows it was partitioned as one dynamic GPT-disk having 4 TB NTFS volume. There is a lot of music and movies on the drive. I'm trying to get him to be seen under Ubuntu as a single disk, not as 2 by 2 terabytes. I tried to read it through dmraid, had no success, it is not displayed in /dev/mapper. Also tried to configure the kernel, but did not find anything suspicious, the driver for my controller was on. There is also a driver from the manufacturer, but it is only available for RHEL and SLES. Here it's reported that SoftRAID is supported by the kernel, but apparently not completely. If I thrust drives in the AMD controller, built into the motherboard, the drive is seen as a single, but the data is lost. I know about mdadm that it is able to ditch all the information on the disks. So, is it possible to somehow create an array without actually recording information on used drives and to make the system correctly identify sections on it later? Information about the array: /dev/sdf - Disk 0 /dev/sdg - Disk 1 Array type: Stripe Block Size: 64KB Also, a device /dev/md1 is created using command mknod /dev/md1 b 9 1

  Read the article

• Recommended storage scheme for home server? (LVM/JBOD/RAID 5...)

  - by j-g-faustus

  Are there any guidelines for which storage scheme(s) makes most sense for a multiple-disk home server? I am assuming a separate boot/OS disk (so bootability is not a concern, this is for data storage only) and 4-6 storage disks of 1-2 TB each, for a total storage capacity in the range 4-12 TB. The file system is ext4, I expect there will be only one big partition spanning all disks. As far as I can tell, the alternatives are individual disks pros: works with any combination of disk sizes; losing a disk loses only the data on that disk; no need for volume management. cons: data management is clumsy when logical units (like a "movies" folder) are larger than the capacity of any single drive. JBOD span pros: can merge disks of any size. cons: losing a disk loses all data on all disks LVM pros: can merge disks of any size; relatively simple to add and remove disks. cons: losing a disk loses all data on all disks RAID 0 pros: speed cons: losing one drive loses all data; disks must be same size RAID 5 pros: data survives losing one disk cons: gives up one disk worth of capacity; disks must be same size RAID 6 pros: data survives losing two disks cons: gives up two disks worth of capacity; disks must be same size I'm primarily considering either LVM or JBOD span simply because it will let me reuse older, smaller-capacity disks when I upgrade the system. The runner-up is RAID 0 for speed. I'm planning on having full backups to a separate system, so I expect the extra redundancy from RAID levels 5 or 6 won't be important. Is this a fair representation of the alternatives? Are there other considerations or alternatives I have missed? And what would you recommend?

  Read the article

• Installed ubuntu over windows vista..cant reinstall windows

  - by Marcuz J Hinojoz

  I recently used the "compress hard drive" option within windows. i got the horid "boot mngr is compressed" after the restart. i tried booting my system back to windows vista but it doesnt read the cd that came with my computer. i tried going into system recovery and going back to a previous date but it didnt work. i kept pressing f8 but nothing. i installed ubuntu(the ubuntu cd worked but windows didnt?) i installed ubuntu so i could atleast get in my computer, and i still wasnt able to install windows from there. my hard drive got reformatted to a ext4? and windows cant install because it doesnt read it? im not sure, but its very frustrating. my computer is a gateway gt5668e windows vista home premium with sp1. im a graphic designer and use programs such as photoshop and cinema 4d to do my projects..i have been at a unfortunate halt with my work and i am really bummed out and dont know what to do... any help?

  Read the article

• What is the difference between the "Entire Partition" and "Entire Disc"?

  - by Roman

  I want to install Ubuntu alongside my Windows 7 operation system. During installation I have three options: Install alongside the existing OS. Remove everything and install Ubuntu. Manual partitioning (advanced). The above list is not precise (I do not remember what exactly was written there and I just write options as I have understood them). I know that option 2 is not mine. So, I need to choose either 1 or 3. I do not know which one I need to choose. I want to have a possibility to manually specify space assigned to Windows and Ubuntu (for example 40% for Windows and 60% for Ubuntu). I chose the 1st option and I saw a window with the following information. Allocate drive space by dragging the drive bellow. File (48.1 GB) Ubuntu /dev/sda2 (ntfs) /dev/sda3 (ext4) 286.6 GB 241.7 GB 2 small partitions are hidden, use the advanced partitioning tool for more control. [use entire partition] [use entire disk] [Quit] [Back] [Install Now] My problem is that I do not understand what I see. In particular I can press [use entire partition] or [use entire disk] and I do not know what is the difference. Moreover, as far as I understand, I can even press [Install Now] without pressing one of the two above mentioned buttons. So, I have 3 options. What is the difference between them? The most important thing for me is not to delete the old operation system with all the data stored there.

  Read the article

• Why is my HDD going back from standy?

  - by Pablo

  My hard drives, connected to Ubuntu server are producing the following log every exactly 5 minutes. Nov 1 14:10:50 localhost kernel: [ 1602.884936] ata2.00: hard resetting link Nov 1 14:10:51 localhost kernel: [ 1603.226804] ata2.01: hard resetting link Nov 1 14:10:52 localhost kernel: [ 1604.274533] ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Nov 1 14:10:52 localhost kernel: [ 1604.274548] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Nov 1 14:10:52 localhost kernel: [ 1604.356669] ata2.00: configured for UDMA/133 Nov 1 14:10:52 localhost kernel: [ 1604.375247] ata2.01: configured for UDMA/133 Nov 1 14:10:52 localhost kernel: [ 1604.375265] ata2: EH complete I don't think this is related to hard drive failure, because it happens for ALL hard drives connected and ONLY when I write spindown_time = 12 in /etc/hdparm.conf. The reason I add this value is to put disks into standby mode after 60 seconds, which is happening after that period (checked with hdparm -C). The first clue I thought that smartd was running and spinning the drive. However, I couldn't find it in ps -aux | grep smart. Additionally, iostat does show that nobody accessed those drives, since Blk_read, Blk_wrtn remain unchanged. I also killed all processes that may be doing something with hdd(eg SAMBA). So I guess the problem is solely with hdparm... I have no more clue where that 5 minute value hides.

  Read the article

• Am I running out of memory or do I have two logical drives instead of one

  - by user30904

  I did a complete reinstall of Ubuntu 13.04 a couple of months ago. Since then, I have switched out my motherboard with another. I kept the same hard drive. I just did an upgrade to 13.10. Recently, after this install, I keep getting the message that I'm running out of memory. I just checked my system usage and was surprised by what I found. I believed that I installed Ubuntu as a fresh install but when I check the system usage, it seems like there are two logical drives. I just did the basic install, so I was only expecting to see one partition but instead I see two. One is a small 300mb partition, the other is a 300gb partition I was expecting. Can anyone tell me if I have two partitions and/or logical drives and if so how I can fix this? I seem to have been running on the smaller drive and now I'm obviously out of space. I want to be able to use the bigger one at least.

  Read the article

• raid advice with SSD and two HDD

  - by Nin

  I have a new machine with one 128GB SSD and two 1TB HDD. On the SSD is the OS and my initial thought was to put the two HDD in RAID 1 for user data. After some more thought I came up with two other setups and now I'm in doubt :) Can someone advise what would be the best setup? 1: single SSD and HDD in RAID 1 (original thought) 2: Create 2 partitions on the HDD (128GB and 872GB). Put the two 872GB in RAID 1 and create another RAID 1 with the SSD and one 128GB HDD partition. 3: Create 2 partitions on the HDD (750/250), put the 705GB in RAID 1 and use the 2 250GB as backup and make automatic snapshots of the SSD to (one of) these partitions. I think the 2 main questions are: Is it advisable to create a raid array with only part of a drive and actively use the other part of that drive or should you always use the full disk? Is it advisable to create a raid 1 array with a SSD and HDD or will that blow the whole speed advantage of the SSD?

  Read the article

• Spring security request matcher is not working with regex

  - by Felipe Cardoso Martins

  Using Spring MVC + Security I have a business requirement that the users from SEC (Security team) has full access to the application and FRAUD (Anti-fraud team) has only access to the pages that URL not contains the words "block" or "update" with case insensitive. Bellow, all spring dependencies: $ mvn dependency:tree | grep spring [INFO] +- org.springframework:spring-webmvc:jar:3.1.2.RELEASE:compile [INFO] | +- org.springframework:spring-asm:jar:3.1.2.RELEASE:compile [INFO] | +- org.springframework:spring-beans:jar:3.1.2.RELEASE:compile [INFO] | +- org.springframework:spring-context:jar:3.1.2.RELEASE:compile [INFO] | +- org.springframework:spring-context-support:jar:3.1.2.RELEASE:compile [INFO] | \- org.springframework:spring-expression:jar:3.1.2.RELEASE:compile [INFO] +- org.springframework:spring-core:jar:3.1.2.RELEASE:compile [INFO] +- org.springframework:spring-web:jar:3.1.2.RELEASE:compile [INFO] +- org.springframework.security:spring-security-core:jar:3.1.2.RELEASE:compile [INFO] | \- org.springframework:spring-aop:jar:3.0.7.RELEASE:compile [INFO] +- org.springframework.security:spring-security-web:jar:3.1.2.RELEASE:compile [INFO] | +- org.springframework:spring-jdbc:jar:3.0.7.RELEASE:compile [INFO] | \- org.springframework:spring-tx:jar:3.0.7.RELEASE:compile [INFO] +- org.springframework.security:spring-security-config:jar:3.1.2.RELEASE:compile [INFO] +- org.springframework.security:spring-security-acl:jar:3.1.2.RELEASE:compile Bellow, some examples of mapped URL path from spring log: Mapped URL path [/index] onto handler 'homeController' Mapped URL path [/index.*] onto handler 'homeController' Mapped URL path [/index/] onto handler 'homeController' Mapped URL path [/cellphone/block] onto handler 'cellphoneController' Mapped URL path [/cellphone/block.*] onto handler 'cellphoneController' Mapped URL path [/cellphone/block/] onto handler 'cellphoneController' Mapped URL path [/cellphone/confirmBlock] onto handler 'cellphoneController' Mapped URL path [/cellphone/confirmBlock.*] onto handler 'cellphoneController' Mapped URL path [/cellphone/confirmBlock/] onto handler 'cellphoneController' Mapped URL path [/user/update] onto handler 'userController' Mapped URL path [/user/update.*] onto handler 'userController' Mapped URL path [/user/update/] onto handler 'userController' Mapped URL path [/user/index] onto handler 'userController' Mapped URL path [/user/index.*] onto handler 'userController' Mapped URL path [/user/index/] onto handler 'userController' Mapped URL path [/search] onto handler 'searchController' Mapped URL path [/search.*] onto handler 'searchController' Mapped URL path [/search/] onto handler 'searchController' Mapped URL path [/doSearch] onto handler 'searchController' Mapped URL path [/doSearch.*] onto handler 'searchController' Mapped URL path [/doSearch/] onto handler 'searchController' Bellow, a test of the regular expressions used in spring-security.xml (I'm not a regex speciality, improvements are welcome =]): import java.util.Arrays; import java.util.List; public class RegexTest { public static void main(String[] args) { List<String> pathSamples = Arrays.asList( "/index", "/index.*", "/index/", "/cellphone/block", "/cellphone/block.*", "/cellphone/block/", "/cellphone/confirmBlock", "/cellphone/confirmBlock.*", "/cellphone/confirmBlock/", "/user/update", "/user/update.*", "/user/update/", "/user/index", "/user/index.*", "/user/index/", "/search", "/search.*", "/search/", "/doSearch", "/doSearch.*", "/doSearch/"); for (String pathSample : pathSamples) { System.out.println("Path sample: " + pathSample + " - SEC: " + pathSample.matches("^.*$") + " | FRAUD: " + pathSample.matches("^(?!.*(?i)(block|update)).*$")); } } } Bellow, the console result of Java class above: Path sample: /index - SEC: true | FRAUD: true Path sample: /index.* - SEC: true | FRAUD: true Path sample: /index/ - SEC: true | FRAUD: true Path sample: /cellphone/block - SEC: true | FRAUD: false Path sample: /cellphone/block.* - SEC: true | FRAUD: false Path sample: /cellphone/block/ - SEC: true | FRAUD: false Path sample: /cellphone/confirmBlock - SEC: true | FRAUD: false Path sample: /cellphone/confirmBlock.* - SEC: true | FRAUD: false Path sample: /cellphone/confirmBlock/ - SEC: true | FRAUD: false Path sample: /user/update - SEC: true | FRAUD: false Path sample: /user/update.* - SEC: true | FRAUD: false Path sample: /user/update/ - SEC: true | FRAUD: false Path sample: /user/index - SEC: true | FRAUD: true Path sample: /user/index.* - SEC: true | FRAUD: true Path sample: /user/index/ - SEC: true | FRAUD: true Path sample: /search - SEC: true | FRAUD: true Path sample: /search.* - SEC: true | FRAUD: true Path sample: /search/ - SEC: true | FRAUD: true Path sample: /doSearch - SEC: true | FRAUD: true Path sample: /doSearch.* - SEC: true | FRAUD: true Path sample: /doSearch/ - SEC: true | FRAUD: true Tests Scenario 1 Bellow, the important part of spring-security.xml: <security:http entry-point-ref="entryPoint" request-matcher="regex"> <security:intercept-url pattern="^.*$" access="ROLE_SEC" /> <security:intercept-url pattern="^(?!.*(?i)(block|update)).*$" access="ROLE_FRAUD" /> <security:access-denied-handler error-page="/access-denied.html" /> <security:form-login always-use-default-target="false" login-processing-url="/doLogin.html" authentication-failure-handler-ref="authFailHandler" authentication-success-handler-ref="authSuccessHandler" /> <security:logout logout-url="/logout.html" success-handler-ref="logoutSuccessHandler" /> </security:http> Behaviour: FRAUD group **can't" access any page SEC group works fine Scenario 2 NOTE that I only changed the order of intercept-url in spring-security.xml bellow: <security:http entry-point-ref="entryPoint" request-matcher="regex"> <security:intercept-url pattern="^(?!.*(?i)(block|update)).*$" access="ROLE_FRAUD" /> <security:intercept-url pattern="^.*$" access="ROLE_SEC" /> <security:access-denied-handler error-page="/access-denied.html" /> <security:form-login always-use-default-target="false" login-processing-url="/doLogin.html" authentication-failure-handler-ref="authFailHandler" authentication-success-handler-ref="authSuccessHandler" /> <security:logout logout-url="/logout.html" success-handler-ref="logoutSuccessHandler" /> </security:http> Behaviour: SEC group **can't" access any page FRAUD group works fine Conclusion I did something wrong or spring-security have a bug. The problem already was solved in a very bad way, but I need to fix it quickly. Anyone knows some tricks to debug better it without open the frameworks code? Cheers, Felipe

  Read the article

• How do I mount my External HDD with filesystem type errors?

  - by Snuggie

  I am a relatively new Ubuntu user and I am having some difficulty mounting my external 2TB HDD. When I first installed Linux my external HDD was working just fine, however, it has stopped working and I have a lot of important files on there that I need. Before my HDD would automatically mount and no worries. Now, however, it doesn't automatically mount and when I try to manually mount it I keep running into filesystem type errors that I can't seem to get past. Below are images that depict my step by step process of how I am trying to mount my HDD along with the errors I am receiving. If anybody has any idea what I am doing wrong or how to correct the issue I would greatly appreciate it. Step 1) Ensure the computer recognizes my external HDD. pj@PJ:~$ dmesg ... [ 5790.367910] scsi 7:0:0:0: Direct-Access WD My Passport 0748 1022 PQ: 0 ANSI: 6 [ 5790.368278] scsi 7:0:0:1: Enclosure WD SES Device 1022 PQ: 0 ANSI: 6 [ 5790.370122] sd 7:0:0:0: Attached scsi generic sg2 type 0 [ 5790.370310] ses 7:0:0:1: Attached Enclosure device [ 5790.370462] ses 7:0:0:1: Attached scsi generic sg3 type 13 [ 5792.971601] sd 7:0:0:0: [sdb] 3906963456 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 5792.972148] sd 7:0:0:0: [sdb] Write Protect is off [ 5792.972162] sd 7:0:0:0: [sdb] Mode Sense: 47 00 10 08 [ 5792.972591] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.972605] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.975235] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.975249] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.987504] sdb: sdb1 [ 5792.988900] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.988911] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.988920] sd 7:0:0:0: [sdb] Attached SCSI disk Step 2) Check if it mounted properly (it does not) pj@PJ:~$ df -ah Filesystem Size Used Avail Use% Mounted on /dev/sda1 682G 3.9G 644G 1% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys none 0 0 0 - /sys/fs/fuse/connections none 0 0 0 - /sys/kernel/debug none 0 0 0 - /sys/kernel/security udev 2.9G 4.0K 2.9G 1% /dev devpts 0 0 0 - /dev/pts tmpfs 1.2G 928K 1.2G 1% /run none 5.0M 0 5.0M 0% /run/lock none 2.9G 156K 2.9G 1% /run/shm gvfs-fuse-daemon 0 0 0 - /home/pj/.gvfs Step 3) Try mounting manually using NTFS and VFAT (both as SDB and SDB1) pj@PJ:~$ sudo mount /dev/sdb /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount /dev/sdb1 /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t ntfs /dev/sdb /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t vfat /dev/sdb /media/Passport/ mount: wrong fs type, bad option, bad superblock on /dev/sdb, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so pj@PJ:~$ sudo mount -t ntfs /dev/sdb1 /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t vfat /dev/sdb1 /media/Passport/ mount: wrong fs type, bad option, bad superblock on /dev/sdb1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so

  Read the article

• External USB drive is failing

  - by dma_k

  I have an external USB 2.0 drive WD My Book Mirror Edition, running in RAID 1 (mirroring) mode. A while ago the hard drive started to fail: it stops responding (directories are not listed returning an error after a big timeout). Sometimes it works for weeks before a failure, sometimes – few hours. Small write operations (like removing few files or editing a small file) do not harm, but when copying large files to the drive over the network, or creating the archive locally, the kernel dumps. Also interesting to note that once kernel has failed, Linux does not want to reboot normally (reboot hangs); when Linux box is shutdown with power button, WD drive does not go to sleep mode (as it usually does): leds continue to run, pressing and holding the "shutdown" button on drive's back panel does not do anything; only unplugging the power cord helps. Here goes the boot log: Aug 16 00:32:21 kernel: [ 1.514106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Aug 16 00:32:21 kernel: [ 1.657738] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 1.673747] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 1.673751] ehci_hcd 0000:00:1d.7: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.725224] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Aug 16 00:32:21 kernel: [ 1.741647] ehci_hcd 0000:00:1d.7: using broken periodic workaround Aug 16 00:32:21 kernel: [ 1.761790] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported Aug 16 00:32:21 kernel: [ 1.761873] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdfff000 Aug 16 00:32:21 kernel: [ 1.796043] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Aug 16 00:32:21 kernel: [ 1.879069] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Aug 16 00:32:21 kernel: [ 1.895446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 1.911796] usb usb1: Product: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.928015] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd Aug 16 00:32:21 kernel: [ 1.944331] usb usb1: SerialNumber: 0000:00:1d.7 Aug 16 00:32:21 kernel: [ 1.961285] usb usb1: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 1.994412] hub 1-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.010864] hub 1-0:1.0: 8 ports detected Aug 16 00:32:21 kernel: [ 2.085939] uhci_hcd: USB Universal Host Controller Interface driver Aug 16 00:32:21 kernel: [ 2.191945] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 2.226029] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.226034] uhci_hcd 0000:00:1d.0: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.243237] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Aug 16 00:32:21 kernel: [ 2.260390] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fe00 Aug 16 00:32:21 kernel: [ 2.277517] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.294815] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.312173] usb usb2: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.329534] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.346828] usb usb2: SerialNumber: 0000:00:1d.0 Aug 16 00:32:21 kernel: [ 2.412989] usb usb2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.430651] usb 1-2: new high speed USB device using ehci_hcd and address 2 Aug 16 00:32:21 kernel: [ 2.449046] hub 2-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.466514] hub 2-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.484639] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Aug 16 00:32:21 kernel: [ 2.537750] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.537756] uhci_hcd 0000:00:1d.1: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.555085] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Aug 16 00:32:21 kernel: [ 2.572231] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fd00 Aug 16 00:32:21 kernel: [ 2.589593] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.606869] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.624134] usb usb3: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.641329] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.658505] usb usb3: SerialNumber: 0000:00:1d.1 Aug 16 00:32:21 kernel: [ 2.675843] usb usb3: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.692864] hub 3-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.709651] hub 3-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.727378] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Aug 16 00:32:21 kernel: [ 2.768252] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.768258] uhci_hcd 0000:00:1d.2: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.806679] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Aug 16 00:32:21 kernel: [ 2.824117] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00 Aug 16 00:32:21 kernel: [ 2.841405] usb 1-2: New USB device found, idVendor=1058, idProduct=1104 Aug 16 00:32:21 kernel: [ 2.858448] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Aug 16 00:32:21 kernel: [ 2.875347] usb 1-2: Product: My Book Aug 16 00:32:21 kernel: [ 2.892113] usb 1-2: Manufacturer: Western Digital Aug 16 00:32:21 kernel: [ 2.908915] usb 1-2: SerialNumber: 575532553130303530353538 Aug 16 00:32:21 kernel: [ 2.943242] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.960405] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.977615] usb usb4: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.994687] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.011711] usb usb4: SerialNumber: 0000:00:1d.2 Aug 16 00:32:21 kernel: [ 3.029589] usb usb4: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.082027] sd 2:0:0:0: [sda] Attached SCSI disk Aug 16 00:32:21 kernel: [ 3.103953] usb 1-2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.122625] hub 4-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.140484] hub 4-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.161680] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 Aug 16 00:32:21 kernel: [ 3.181257] uhci_hcd 0000:00:1d.3: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 3.181263] uhci_hcd 0000:00:1d.3: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.198614] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Aug 16 00:32:21 kernel: [ 3.216012] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00 Aug 16 00:32:21 kernel: [ 3.249877] Uniform CD-ROM driver Revision: 3.20 Aug 16 00:32:21 kernel: [ 3.267765] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 3.284947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 3.302023] usb usb5: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.319215] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.336298] usb usb5: SerialNumber: 0000:00:1d.3 Aug 16 00:32:21 kernel: [ 3.368377] Initializing USB Mass Storage driver... Aug 16 00:32:21 kernel: [ 3.390652] usbcore: registered new interface driver hiddev Aug 16 00:32:21 kernel: [ 3.408109] scsi4 : SCSI emulation for USB Mass Storage devices Aug 16 00:32:21 kernel: [ 3.425281] sr 0:0:1:0: Attached scsi CD-ROM sr0 Aug 16 00:32:21 kernel: [ 3.438978] sr 0:0:1:0: Attached scsi generic sg0 type 5 Aug 16 00:32:21 kernel: [ 3.456328] usbcore: registered new interface driver usb-storage Aug 16 00:32:21 kernel: [ 3.474564] usb-storage: device found at 2 Aug 16 00:32:21 kernel: [ 3.474567] usb-storage: waiting for device to settle before scanning Aug 16 00:32:21 kernel: [ 3.475320] sd 2:0:0:0: Attached scsi generic sg1 type 0 Aug 16 00:32:21 kernel: [ 3.492587] USB Mass Storage support registered. Aug 16 00:32:21 kernel: [ 3.510930] usb usb5: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.531076] hub 5-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.548399] hub 5-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.591743] input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.1/input/input2 Aug 16 00:32:21 kernel: [ 3.609515] generic-usb 0003:1058:1104.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-2/input1 Aug 16 00:32:21 kernel: [ 3.627466] usbcore: registered new interface driver usbhid Aug 16 00:32:21 kernel: [ 8.581664] usb-storage: device scan complete Aug 16 00:32:21 kernel: [ 8.624270] scsi 4:0:0:0: Direct-Access WD My Book 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.655135] scsi 4:0:0:1: Enclosure WD My Book Device 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.675393] sd 4:0:0:0: Attached scsi generic sg2 type 0 Aug 16 00:32:21 kernel: [ 8.698669] scsi 4:0:0:1: Attached scsi generic sg3 type 13 Aug 16 00:32:21 kernel: [ 8.723370] sd 4:0:0:0: [sdb] 1953513472 512-byte logical blocks: (1.00 TB/931 GiB) Aug 16 00:32:21 kernel: [ 8.750477] sd 4:0:0:0: [sdb] Write Protect is off Aug 16 00:32:21 kernel: [ 8.769411] sd 4:0:0:0: [sdb] Mode Sense: 10 00 00 00 Aug 16 00:32:21 kernel: [ 8.769414] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.822971] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.841978] sdb: sdb1 Aug 16 00:32:21 kernel: [ 8.905580] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.924173] sd 4:0:0:0: [sdb] Attached SCSI disk Aug 16 00:32:21 kernel: [ 11.600492] XFS mounting filesystem sdb1 Aug 16 00:32:21 kernel: [ 12.222948] Ending clean XFS mount for filesystem: sdb1 After a while the following appears in a log: Aug 16 09:30:56 kernel: [32359.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:31:59 kernel: [32422.112035] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:33:00 kernel: [32483.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 And then it is followed by few kernel dumps, which I think, are not good: Aug 16 09:33:40 kernel: [32520.428027] INFO: task xfssyncd:1002 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32520.462689] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32520.497422] xfssyncd D c3d84a60 0 1002 2 0x00000000 Aug 16 09:33:40 kernel: [32520.532117] f6c9aa80 00000046 c1132742 c3d84a60 00000286 c1418100 c1418100 00000000 Aug 16 09:33:40 kernel: [32520.566867] f6c9ac3c c2808100 00000000 f653b18b 00001d76 00000001 f6c9aa80 c3c3f0e0 Aug 16 09:33:40 kernel: [32520.601343] 08e59242 f6c9ac3c 2e41392b 00000000 08e59242 00000000 c3f7fb48 0067385a Aug 16 09:33:40 kernel: [32520.635533] Call Trace: Aug 16 09:33:40 kernel: [32520.668991] [<c1132742>] ? cfq_set_request+0x0/0x290 Aug 16 09:33:40 kernel: [32520.702804] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32520.736555] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32520.770360] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32520.804110] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32520.837713] [<c1128230>] ? blk_peek_request+0x135/0x143 Aug 16 09:33:40 kernel: [32520.871265] [<f8582987>] ? scsi_dispatch_cmd+0x185/0x1e5 [scsi_mod] Aug 16 09:33:40 kernel: [32520.904407] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32520.937007] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32520.969033] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.000485] [<c10cffd1>] ? bio_add_page+0x28/0x2e Aug 16 09:33:40 kernel: [32521.031403] [<f8918d38>] ? _xfs_buf_ioapply+0x206/0x22b [xfs] Aug 16 09:33:40 kernel: [32521.061888] [<f89197bd>] ? xfs_buf_iorequest+0x38/0x60 [xfs] Aug 16 09:33:40 kernel: [32521.091845] [<f8907230>] ? xlog_bdstrat_cb+0x16/0x3d [xfs] Aug 16 09:33:40 kernel: [32521.121222] [<f8905781>] ? XFS_bwrite+0x32/0x64 [xfs] Aug 16 09:33:40 kernel: [32521.150007] [<f89059be>] ? xlog_sync+0x20b/0x311 [xfs] Aug 16 09:33:40 kernel: [32521.178214] [<f89112fc>] ? xfs_trans_ail_tail+0x12/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.205914] [<f8906261>] ? xlog_state_sync_all+0xa2/0x141 [xfs] Aug 16 09:33:40 kernel: [32521.233074] [<f8906611>] ? _xfs_log_force+0x51/0x68 [xfs] Aug 16 09:33:40 kernel: [32521.259664] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32521.285662] [<f8906636>] ? xfs_log_force+0xe/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.311171] [<f89202df>] ? xfs_sync_worker+0x17/0x5c [xfs] Aug 16 09:33:40 kernel: [32521.336117] [<f891fbb7>] ? xfssyncd+0x134/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.360498] [<f891fa83>] ? xfssyncd+0x0/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.384211] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32521.407890] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32521.430876] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32521.453394] INFO: task flush-8:16:12945 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32521.476116] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32521.498579] flush-8:16 D 00000000 0 12945 2 0x00000000 Aug 16 09:33:40 kernel: [32521.520649] f4e4d540 00000046 e412e940 00000000 00000002 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32521.542426] f4e4d6fc c2808100 00000000 00000000 000008b4 00000001 f4e4d540 c3c3f0e0 Aug 16 09:33:40 kernel: [32521.563745] 02e905a8 f4e4d6fc 007a5399 00000000 02e905a8 00000000 f4e2db48 00670b98 Aug 16 09:33:40 kernel: [32521.585077] Call Trace: Aug 16 09:33:40 kernel: [32521.605790] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32521.626184] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32521.646133] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32521.665659] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32521.684716] [<f891796e>] ? xfs_convert_page+0x30a/0x331 [xfs] Aug 16 09:33:40 kernel: [32521.703366] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32521.721644] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32521.739465] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.756896] [<c10cfa45>] ? bio_alloc_bioset+0x7b/0xba Aug 16 09:33:40 kernel: [32521.774046] [<f8917af0>] ? xfs_submit_ioend_bio+0x3b/0x44 [xfs] Aug 16 09:33:40 kernel: [32521.790694] [<f8917ba3>] ? xfs_submit_ioend+0xaa/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.806736] [<f891817d>] ? xfs_page_state_convert+0x5c0/0x61c [xfs] Aug 16 09:33:40 kernel: [32521.822859] [<c113705b>] ? __lookup_tag+0x8e/0xee Aug 16 09:33:40 kernel: [32521.838958] [<f891840d>] ? xfs_vm_writepage+0x91/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.855039] [<c108bbcc>] ? __writepage+0x8/0x22 Aug 16 09:33:40 kernel: [32521.871067] [<c108c17b>] ? write_cache_pages+0x1af/0x29f Aug 16 09:33:40 kernel: [32521.886616] [<c108bbc4>] ? __writepage+0x0/0x22 Aug 16 09:33:40 kernel: [32521.901593] [<c108c285>] ? generic_writepages+0x1a/0x21 Aug 16 09:33:40 kernel: [32521.916455] [<f8918338>] ? xfs_vm_writepages+0x0/0x38 [xfs] Aug 16 09:33:40 kernel: [32521.931484] [<c108c2a5>] ? do_writepages+0x19/0x25 Aug 16 09:33:40 kernel: [32521.946648] [<c10c80d9>] ? writeback_single_inode+0xc7/0x273 Aug 16 09:33:40 kernel: [32521.961675] [<c10c8c44>] ? writeback_inodes_wb+0x3dd/0x49c Aug 16 09:33:40 kernel: [32521.976831] [<c10c8e18>] ? wb_writeback+0x115/0x178 Aug 16 09:33:40 kernel: [32521.991778] [<c10c901f>] ? wb_do_writeback+0x121/0x131 Aug 16 09:33:40 kernel: [32522.006538] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32522.021091] [<c10c9050>] ? bdi_writeback_task+0x21/0x89 Aug 16 09:33:40 kernel: [32522.035493] [<c10979e5>] ? bdi_start_fn+0x59/0xa4 Aug 16 09:33:40 kernel: [32522.049765] [<c109798c>] ? bdi_start_fn+0x0/0xa4 Aug 16 09:33:40 kernel: [32522.063792] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32522.077612] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32522.091260] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32522.104966] INFO: task smartctl:13098 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32522.118883] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32522.133012] smartctl D 00000020 0 13098 13097 0x00000000 Aug 16 09:33:40 kernel: [32522.147221] e50b9540 00000086 c11d28a8 00000020 00000770 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32522.161720] e50b96fc c2808100 00000000 e53e8800 00000000 00000020 c3cec000 c13886c0 Aug 16 09:33:40 kernel: [32522.176217] f99dab68 e50b96fc 007a4f1e 00000001 c4082f24 c4082ed8 00000001 c3c3f0e0 Aug 16 09:33:40 kernel: [32522.190737] Call Trace: Aug 16 09:33:40 kernel: [32522.205038] [<c11d28a8>] ? __netdev_alloc_skb+0x14/0x2d Aug 16 09:33:40 kernel: [32522.219605] [<c126b799>] ? schedule_timeout+0x20/0xb0 Aug 16 09:33:40 kernel: [32522.234144] [<c112820d>] ? blk_peek_request+0x112/0x143 Aug 16 09:33:40 kernel: [32522.248649] [<f85873b6>] ? scsi_request_fn+0x3c1/0x47a [scsi_mod] Aug 16 09:33:40 kernel: [32522.263233] [<c103aba8>] ? del_timer+0x55/0x5c Aug 16 09:33:40 kernel: [32522.277773] [<c126b6a2>] ? wait_for_common+0xa4/0x100 Aug 16 09:33:40 kernel: [32522.292342] [<c102cd8d>] ? default_wake_function+0x0/0x8 Aug 16 09:33:40 kernel: [32522.306958] [<c112b3d1>] ? blk_execute_rq+0x8b/0xb2 Aug 16 09:33:40 kernel: [32522.321569] [<c112b2ac>] ? blk_end_sync_rq+0x0/0x23 Aug 16 09:33:40 kernel: [32522.336070] [<c112b58b>] ? blk_recount_segments+0x13/0x20 Aug 16 09:33:40 kernel: [32522.350583] [<c1127307>] ? blk_rq_bio_prep+0x44/0x74 Aug 16 09:33:40 kernel: [32522.365059] [<c112b0b2>] ? blk_rq_map_kern+0xc5/0xee Aug 16 09:33:40 kernel: [32522.379439] [<c112e2a5>] ? sg_scsi_ioctl+0x221/0x2aa Aug 16 09:33:40 kernel: [32522.393801] [<c112e672>] ? scsi_cmd_ioctl+0x344/0x39a Aug 16 09:33:40 kernel: [32522.408140] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.422566] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.436832] [<f87676aa>] ? sd_ioctl+0x90/0xb5 [sd_mod] Aug 16 09:33:40 kernel: [32522.451228] [<c112c35f>] ? __blkdev_driver_ioctl+0x53/0x63 Aug 16 09:33:40 kernel: [32522.465689] [<c112cbbf>] ? blkdev_ioctl+0x850/0x891 Aug 16 09:33:40 kernel: [32522.479982] [<c1020474>] ? __wake_up_common+0x34/0x59 Aug 16 09:33:40 kernel: [32522.494138] [<c10244cd>] ? complete+0x28/0x36 Aug 16 09:33:40 kernel: [32522.507986] [<c1086c64>] ? find_get_page+0x1f/0x81 Aug 16 09:33:40 kernel: [32522.521671] [<c10abed5>] ? add_partial+0xe/0x40 Aug 16 09:33:40 kernel: [32522.535285] [<c1086e68>] ? lock_page+0x8/0x1d Aug 16 09:33:40 kernel: [32522.548797] [<c1087432>] ? filemap_fault+0xb5/0x2e6 Aug 16 09:33:40 kernel: [32522.562141] [<c109941c>] ? __do_fault+0x381/0x3b1 Aug 16 09:33:40 kernel: [32522.575441] [<c10d0c30>] ? block_ioctl+0x27/0x2c Aug 16 09:33:40 kernel: [32522.588708] [<c10d0c09>] ? block_ioctl+0x0/0x2c Aug 16 09:33:40 kernel: [32522.601858] [<c10bcd78>] ? vfs_ioctl+0x1c/0x5f Aug 16 09:33:40 kernel: [32522.614917] [<c10bd30c>] ? do_vfs_ioctl+0x4aa/0x4e5 Aug 16 09:33:40 kernel: [32522.627961] [<c10350db>] ? __do_softirq+0x115/0x151 Aug 16 09:33:40 kernel: [32522.640901] [<c126e270>] ? do_page_fault+0x2f1/0x307 Aug 16 09:33:40 kernel: [32522.653803] [<c10bd388>] ? sys_ioctl+0x41/0x58 Aug 16 09:33:40 kernel: [32522.666674] [<c10030fb>] ? sysenter_do_call+0x12/0x28 Then again few messages reset high speed USB device using ehci_hcd and address 2. I have browsed and read similar error reports here and there and I tried: I have upgraded the kernel from v2.6.26-2 to 2.6.32-5, which has not solved the problem. They say, this might a cable problem. I have tried to replace the USB-to-miniUSB cable (that connects external drive with computer) with another one. No changes. Somebody suggests to try another USB port. I have only 4 external USB ports, tried another one with no success. They say to try uhci_hcd. I have unmounted the device, unloaded ehci_hcd and mounted again. The difference was that now in log I get reset full speed USB device using uhci_hcd and address 2 and similar kernel dumps after a while. They say to echo 128 > /sys/block/sdb/device/max_sectors. I tried it with ehci_hcd with no success (note: I have issued this command after the drive was mounted but before using it actively). I have lauched smartmond and checking periodically the output of smartctl: drive temperature is OK, number of bad sectors and uncorrectable errors is 0. Nothing suspicious is reported by S.M.A.R.T. except maybe the following: Aug 16 12:40:12 kernel: [43715.314566] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Aug 16 12:40:13 kernel: [43715.705622] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Of course, I have not tried all combinations of above. But unfortunately, I am run out of cardinal ideas. If anybody can advice something specific about the problem, you are very welcome.

  Read the article

• How to get full write permission on my second drive after dual boot?

  - by Shaul

  I had a WinXP installation on my hard drive. Then I bought a 2nd drive and installed Win7. Dual boot working fine. But when I'm in the Win7 environment, it appears that I don't have full admin permission on the "D" drive (that's the drive with WinXP). Even though the user I'm logged in as has admin permissions, I have to run my apps with administrator privileges in order to get write access to the D drive. This is not the case when I do stuff on the C drive. I could just get into running those apps that access the D drive in admin mode, but that seems like overkill. Is there some secret switch I can flip so that my D drive acts like my C drive, security-wise?

  Read the article

• mount network drive

  - by CaptnLenz

  since i updated my ubuntu to natty narwhal(from 10.04), my mount script doesn't work anymore. The scripts mounts a folder from a NAS (WD mybookworld) in the local network to a folder in my home folder. script looked like that: #!/bin/bash sudo mount //192.168.2.222/Public/Shared\ Music/ /home/simon/Musik/ error: mount: wrong fs type, bad option, bad superblock on //192.168.2.222/Public/Shared Music/, missing codepage or helper program, or other error (for several filesystems (e.g. nfs, cifs) you might need a /sbin/mount.<type> helper program) Manchmal liefert das Syslog wertvolle Informationen – versuchen Sie dmesg | tail oder so now, because the script doesn't work anymore i decided to add the mount-process to my fstab, because the network drive should be mounted on every startup. My fstab entry looks like this: //192.168.2.222/Public/Shared\ Music/ /home/simon/Musik cifs credentials=/home/simon/.smbcredentials 0 0 But it doesn't work, too. I get a message during the startup process, that Musik couldn't be mounted. Are there any log files i can check for errors? The system is a fresh installed 11.04. Greetings

  Read the article

• mount another drive to the same directory

  - by Ken Autotron

  I recently purchased a server that was advertised as 2TB (2 1TB drives) in size, when I use it it reports only one of the drives, I would like to be able to use both as if one drive. here is the specs... sudo lshw -C disk *-disk description: ATA Disk product: TOSHIBA DT01ACA1 vendor: Toshiba physical id: 0.0.0 bus info: scsi@1:0.0.0 logical name: /dev/sda version: MS2O serial: 13EJ81XPS size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=0005b3dd *-disk description: ATA Disk product: TOSHIBA DT01ACA1 vendor: Toshiba physical id: 0.0.0 bus info: scsi@4:0.0.0 logical name: /dev/sdb version: MS2O serial: 13OX3TKPS size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=00030e86 and fdisk -l Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00030e86 Device Boot Start End Blocks Id System /dev/sdb1 * 4096 41947135 20971520 fd Linux raid autodetect /dev/sdb2 41947136 1952468991 955260928 fd Linux raid autodetect /dev/sdb3 1952468992 1953519615 525312 82 Linux swap / Solaris Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0005b3dd Device Boot Start End Blocks Id System /dev/sda1 * 4096 41947135 20971520 fd Linux raid autodetect /dev/sda2 41947136 1952468991 955260928 fd Linux raid autodetect /dev/sda3 1952468992 1953519615 525312 82 Linux swap / Solaris Disk /dev/md2: 978.2 GB, 978187124736 bytes 2 heads, 4 sectors/track, 238815216 cylinders, total 1910521728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/md1: 21.5 GB, 21474770944 bytes 2 heads, 4 sectors/track, 5242864 cylinders, total 41942912 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table is it possible to mount both drives to say /Home/ so I would have 2TB of usable space?

  Read the article

• How to zero out a drive?

  - by Mohd Arafat Hossain

  I'm currently running Ubuntu 12.04 and want to completely format my laptop so I can install Windows 7 (replace Ubuntu). When I put in my bootable USB with the OS it just shows a black screen with a white blinking cursor on the top left corner. I wait for hours (to be specific 5 whole hours) waiting for something to happen but I get nothing, so I pull out the USB and my Ubuntu 12.04 loads up. Repeated this several times with putting different boot priority options on top-est that relate to USB but the results are same. I go and visit some sites on the net like this http://www.techspot.com/community/topics/cant-replace-ubuntu-with-windows.175716/ that say I have to zero out my hard drive. My question is how? Note: Erasing out all my data is no problem cause I have nothing important to backup. If I have to lose my primary OS (Ubuntu 12.04) in the process I am ready to as my aim is just to install Windows 7 successfully. Please don't answer that there is something wrong with my USB or my USB reader/port/hardware or the content inside the USB cause they all works fine on my brothers PC as it boots up flawlessly.

  Read the article

• updatedb & locate command problem - Files from external hard drive are no longer indexed after rebooting

  - by user784637

  Files from my external hard drive are no longer indexed after rebooting. I have to remount and then run # updatedb after each reboot. The problem is updatedb takes a few minutes for my external hard drives. Is there any way I can retain indexing for my externals after I reboot so that the locate command can search through my externals? EDIT: Per Request here are my specs: $ cat /etc/updatedb.conf PRUNE_BIND_MOUNTS="yes" # PRUNENAMES=".git .bzr .hg .svn" PRUNEPATHS="/tmp /var/spool /media" PRUNEFS="NFS nfs nfs4 rpc_pipefs afs binfmt_misc proc smbfs autofs iso9660 ncpfs coda devpts ftpfs devfs mfs shfs sysfs cifs lustre_lite tmpfs usbfs udf fuse.glusterfs fuse.sshfs ecryptfs fusesmb devtmpfs" # mount /dev/sda5 on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/me/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=me) /dev/sdb1 on /media/me type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096,default_permissions) /dev/sdd1 on /media/Little Boy type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096,default_permissions) /dev/sde1 on /media/Fat Man type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096,default_permissions) # on_ac_power; echo $? 255

  Read the article

• How to create or recover Windows Bootloader after deleting Ubuntu boot drive

  - by Kincaid

  I have a computer that dual-boots (or tri-boots) Windows 8 Release Preview, Windows 7, and Ubuntu 12.04. Grub boots between Windows 8 and Ubuntu; for which I use primarily. Recently, I decided to remove Ubuntu, as I hardly used it. I deleted the Ubuntu partition accidentally before replacing the Grub bootloader. Now, whenever I want to boot the machine, it gives me the "grub-rescue" prompt -- I am unable to boot into either Windows (8 nor 7), nor Ubuntu (except via USB, of course). I do not have any Windows 7/8 recovery media, so that isn't an option. Please note that after I deleted the Ubuntu partition, I put the PC into hibernate, and then turned it on. This means the C:\ [Windows 8] drive cannot be mounted. I don't know if that is bad, but it definitely doesn't make things better. I am currently booting Ubuntu via USB, in an effort to restore the Windows bootloader. I have looked into using boot-repair to solve the problem using the instructions here, although after attempting to apply the changes, it gave the error: "Please install the [mbr] packages. Then try again." I don't know why I'm getting this error; is there a way to install the 'mbr packages?' I honestly don't know what exactly they are, nor how to install them. Are there any other options I have not yet exhausted to be able to boot back into Windows, in the case that there is a better way? I want to set the bootloader to boot into Windows 8, but booting into either Windows 7 or 8 is fine (I can use EasyBCD from there). Is there a simple solution to this? I've checked BIOS, and I haven't been able to find a way to boot into Windows.

  Read the article

• Ubuntu Boot Slow - Late Drive Access

  - by Mo2

  So I just installed Ubuntu on a brand new Samsung 840 Pro SSD and have noticed that it is slower than expected. The LED access light doesn't start blinking until after 20 seconds or so have passed, after which the boot up seems to actually start. Does anyone have any ideas as to why this is happening? I have Windows 7 installed on a separate SSD and use Windows Loader as the main loader. Windows Loader points to GRUB2, from which I then start Ubuntu up. The 20 seconds count that I mentioned earlier starts AFTER I select Ubuntu 14.04.1 from the GRUB2 menu. Any help is appreciated. EDIT: I forgot to mention that I have only one partition for / and /home. I intend on using a shared NTFS drive for my documents and other personal files, so I had no need for the /home. I did not make a /swap since I have 12 GB of RAM. I also did not make a /boot since I was told that it's not really necessary in my case.

  Read the article

• error/message: the disk drive for /home is not ready... when connecting an external hard drive

  - by seallussus

  i am running Ubuntu 10.04 all updated installed to date (3/28/2012) and when i connect another sata HD i get this message the disk drive for /home is not ready yet or not present continue to wait, or press S to skip mounting or M for manual recovery so i press S but i get this message could not update ICEauthority file /home/username/.ICEauthority And when a press close i get this there is a problem with the configuration server (/usr/libconf2-4/gconf-sanity-check-2 exited with status 256) And when a press close i get message Nautilus could not create the following required folders :/home/username/desktop,/home/username/.Nautilus before running Nautilus, please create these folders or set permissons such that Nautilus can reach them And finally when a press Ok at the last message it disappears and i get a blank screen with a lot of colors on it and with nothing else so i shutdown (power button ) and disconnect the HD and boot without problems so how to fix this in simple commands because i am a total Linux noob notes -In the original error my username was in place of username i wrote (did not want to confuse anybody ) -I tried searching for this problem but a got a lot of different answers and most of them were really complicated to me and not working -I got a data HD connected and working without problems also the HD i installed Ubuntu on is Sata (maybe it helps) -Apologize for me bad English its not my mother language

  Read the article

• Can't install Ubuntu 12.04 64-bit on a dual-drive MacBook Pro 8,2

  - by kizdp

  Good afternoon, this is the first time I participate here as I'm new to Linux. I've been trying to solve the following problem for over a week without any sign of success so I hope there's a much more knowledgeable person here that can give me a solution. I have an early 2011 MacBook Pro (8,2) with Mac OS X running in a SSD. Then, instead of the Optical bay, I have a HDD in where I would like to install Ubuntu to run it natively. I've tried to do the normal installation process, with or without rEFIt, but it seems the problem resides on the communication between the device containing the Ubuntu .iso file and the laptop. It doesn't allow communication with the boot CD or USB drive. It usually says: “Loading bootlogo...” after I click on the “boot from CD, Linux Icon”. After trying several things, I would like to know if I could install Ubuntu on the HDD as an external HDD (using a friend's Window's system) and then simply put it back into my laptop so as to become an Internal HDD again. I guess, I would have to reinstall many drivers and so on, but would this approach work? Thanks in advance and sorry for this huge block of text

  Read the article

• How to use C to write to flash drive bootsector despite error 'Failed to open file to write.:Permiss

  - by updateraj

  My goal is to manipulate the boot-sector in my flashdrive (volume E:) I am using XP. I am able to read the boot-sector FILE *fp_read = fopen("\\\\.\\E:", "rb"); /* Able to proceed to read boot sector */ however i am not able to open the file to write using fopen in 'wb' mode. FILE *fp_read = fopen("\\\\.\\E:", "wb"); /* Unable to proceed due to Failed to open file to write.:Permission Denied */ The flash-drive is not in use at the moment of execution. Hex-editors are able to manipulated boot sector etc, i believe it possible to do so in c. Any suggestion or insight to overcome the access problem so as to be able to write?

  Read the article

• How do I change the window that appears when I insert my pen drive?

  - by NeoHaxxor

  Basically all that has to be said has been said in the title. How do I make a window other than the default one pop up when I insert my pen drive into my PC? Can it come from a program in the USB itself as well? Not doing any actual coding yet. Btw- if that default window with al the options has a special name plz tell me. Just so I can word my Google searches better. Any help would be appreciated. Thx

  Read the article

• How to use Secure Erase and is it on the install CD?

  - by Mikey

  Supposedly there is some built in hard drive magic called "Secure Erase" which is wildly faster and more secure than "dd if=/dev/zero..." I am most excited about the speed increase. There seems to be a GUI for it as part of Parted Magic: http://www.ocztechnologyforum.com/forum/showthread.php?81321-Secure-Erase-With-bootable-CD-USB-Linux..-Point-and-Click-Method Is there something like this for Ubuntu? Better yet, is there a way to actually issue this command "manually" like with smartctl or something?

  Read the article

• Can't mount UBS flash drives or my CD/DVD drives

  - by Bret Workman

  How can I fix the permissions to get rid of the following error and mount my USB and internal CD/DVD drive: Adding read ACL for uid 1000 to `/media/bret' failed: Operation not supported These drives worked fin in 12.04, but I apparently now don't have permissions to mount these drives in 12.10. I tried chmod in Terminal, but I couldn't enter as the superuser, so I seem to be stuck. Please help! Thanks

  Read the article

• Ubuntu 12.04 does not recognize Kingston DT108 16GB memory

  - by aceqott

  I bought a Kingston DT108 16GB and Ubuntu did not recognize it.What should i do?? Output of dmesg | tail after connecting pen drive [ 1455.253010] CPU5: Package power limit notification (total events = 488) [ 1455.253013] CPU1: Package power limit notification (total events = 489) [ 1455.263966] CPU4: Package power limit normal [ 1455.263969] CPU2: Package power limit normal [ 1455.263972] CPU0: Package power limit normal [ 1455.263975] CPU6: Package power limit normal [ 1455.263998] CPU1: Package power limit normal [ 1455.264001] CPU5: Package power limit normal [ 1455.264004] CPU7: Package power limit normal [ 1455.264007] CPU3: Package power limit normal

  Read the article

< Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >