Search Results

Search found 2519 results on 101 pages for 'duplex printing'.

Page 62/101 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

• Network Logon Issues with Group Policy and Network

  - by bobloki

  I am gravely in need of your help and assistance. We have a problem with our logon and startup to our Windows 7 Enterprise system. We have more than 3000 Windows Desktops situated in roughly 20+ buildings around campus. Almost every computer on campus has the problem that I will be describing. I have spent over one month peering over etl files from Windows Performance Analyzer (A great product) and hundreds of thousands of event logs. I come to you today humbled that I could not figure this out. The problem as simply put our logon times are extremely long. An average first time logon is roughly 2-10 minutes depending on the software installed. All computers are Windows 7, the oldest computers being 5 years old. Startup times on various computers range from good (1-2 minutes) to very bad (5-60). Our second time logons range from 30 seconds to 4 minutes. We have a gigabit connection between each computer on the network. We have 5 domain controllers which also double as our DNS servers. Initial testing led us to believe that this was a software problem. So I spent a few days testing machines only to find inconsistent results from the etl files from xperfview. Each subset of computers on campus had a different subset of software issues, none seeming to interfere with logon just startup. So I started looking at our group policy and located some very interesting event ID’s. Group Policy 1129: The processing of Group Policy failed because of lack of network connectivity to a domain controller. Group Policy 1055: The processing of Group Policy failed. Windows could not resolve the computer name. This could be caused by one of more of the following: a) Name Resolution failure on the current domain controller. b) Active Directory Replication Latency (an account created on another domain controller has not replicated to the current domain controller). NETLOGON 5719 : This computer was not able to set up a secure session with a domain controller in domain OURDOMAIN due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. E1kexpress 27: Intel®82567LM-3 Gigabit Network Connection – Network link is disconnected. NetBT 4300 – The driver could not be created. WMI 10 - Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor" AND TargetInstance.LoadPercentage 99" could not be reactivated in namespace "//./root/CIMV2" because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected. More or less with timestamps it becomes apparent that the network maybe the issue. 1:25:57 - Group Policy is trying to discover the domain controller information 1:25:57 - The network link has been disconnected 1:25:58 - The processing of Group Policy failed because of lack of network connectivity to a domain controller. This may be a transient condition. A success message would be generated once the machine gets connected to the domain controller and Group Policy has successfully processed. If you do not see a success message for several hours, then contact your administrator. 1:25:58 - Making LDAP calls to connect and bind to active directory. DC1.ourdomain.edu 1:25:58 - Call failed after 0 milliseconds. 1:25:58 - Forcing rediscovery of domain controller details. 1:25:58 - Group policy failed to discover the domain controller in 1030 milliseconds 1:25:58 - Periodic policy processing failed for computer OURDOMAIN\%name%$ in 1 seconds. 1:25:59 - A network link has been established at 1Gbps at full duplex 1:26:00 - The network link has been disconnected 1:26:02 - NtpClient was unable to set a domain peer to use as a time source because of discovery error. NtpClient will try again in 3473457 minutes and DOUBLE THE REATTEMPT INTERVAL thereafter. 1:26:05 - A network link has been established at 1Gbps at full duplex 1:26:08 - Name resolution for the name %Name% timed out after none of the configured DNS servers responded. 1:26:10 – The TCP/IP NetBIOS Helper service entered the running state. 1:26:11 - The time provider NtpClient is currently receiving valid time data at dc4.ourdomain.edu 1:26:14 – User Logon Notification for Customer Experience Improvement Program 1:26:15 - Group Policy received the notification Logon from Winlogon for session 1. 1:26:15 - Making LDAP calls to connect and bind to Active Directory. dc4.ourdomain.edu 1:26:18 - The LDAP call to connect and bind to Active Directory completed. dc4. ourdomain.edu. The call completed in 2309 milliseconds. 1:26:18 - Group Policy successfully discovered the Domain Controller in 2918 milliseconds. 1:26:18 - Computer details: Computer role : 2 Network name : (Blank) 1:26:18 - The LDAP call to connect and bind to Active Directory completed. dc4.ourdomain.edu. The call completed in 2309 milliseconds. 1:26:18 - Group Policy successfully discovered the Domain Controller in 2918 milliseconds. 1:26:19 - The WinHTTP Web Proxy Auto-Discovery Service service entered the running state. 1:26:46 - The Network Connections service entered the running state. 1:27:10 – Retrieved account information 1:27:10 – The system call to get account information completed. 1:27:10 - Starting policy processing due to network state change for computer OURDOMAIN\%name%$ 1:27:10 – Network state change detected 1:27:10 - Making system call to get account information. 1:27:11 - Making LDAP calls to connect and bind to Active Directory. dc4.ourdomain.edu 1:27:13 - Computer details: Computer role : 2 Network name : ourdomain.edu (Now not blank) 1:27:13 - Group Policy successfully discovered the Domain Controller in 2886 milliseconds. 1:27:13 - The LDAP call to connect and bind to Active Directory completed. dc4.ourdomain.edu The call completed in 2371 milliseconds. 1:27:15 - Estimated network bandwidth on one of the connections: 0 kbps. 1:27:15 - Estimated network bandwidth on one of the connections: 8545 kbps. 1:27:15 - A fast link was detected. The Estimated bandwidth is 8545 kbps. The slow link threshold is 500 kbps. 1:27:17 – Powershell - Engine state is changed from Available to Stopped. 1:27:20 - Completed Group Policy Local Users and Groups Extension Processing in 4539 milliseconds. 1:27:25 - Completed Group Policy Scheduled Tasks Extension Processing in 5210 milliseconds. 1:27:27 - Completed Group Policy Registry Extension Processing in 1529 milliseconds. 1:27:27 - Completed policy processing due to network state change for computer OURDOMAIN\%name%$ in 16 seconds. 1:27:27 – The Group Policy settings for the computer were processed successfully. There were no changes detected since the last successful processing of Group Policy. Any help would be appreciated. Please ask for any relevant information and it will be provided as soon as possible.

  Read the article

• Network Logon Issues with Group Policy and Network

  - by bobloki

  I am gravely in need of your help and assistance. We have a problem with our logon and startup to our Windows 7 Enterprise system. We have more than 3000 Windows Desktops situated in roughly 20+ buildings around campus. Almost every computer on campus has the problem that I will be describing. I have spent over one month peering over etl files from Windows Performance Analyzer (A great product) and hundreds of thousands of event logs. I come to you today humbled that I could not figure this out. The problem as simply put our logon times are extremely long. An average first time logon is roughly 2-10 minutes depending on the software installed. All computers are Windows 7, the oldest computers being 5 years old. Startup times on various computers range from good (1-2 minutes) to very bad (5-60). Our second time logons range from 30 seconds to 4 minutes. We have a gigabit connection between each computer on the network. We have 5 domain controllers which also double as our DNS servers. Initial testing led us to believe that this was a software problem. So I spent a few days testing machines only to find inconsistent results from the etl files from xperfview. Each subset of computers on campus had a different subset of software issues, none seeming to interfere with logon just startup. So I started looking at our group policy and located some very interesting event ID’s. Group Policy 1129: The processing of Group Policy failed because of lack of network connectivity to a domain controller. Group Policy 1055: The processing of Group Policy failed. Windows could not resolve the computer name. This could be caused by one of more of the following: a) Name Resolution failure on the current domain controller. b) Active Directory Replication Latency (an account created on another domain controller has not replicated to the current domain controller). NETLOGON 5719 : This computer was not able to set up a secure session with a domain controller in domain OURDOMAIN due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. E1kexpress 27: Intel®82567LM-3 Gigabit Network Connection – Network link is disconnected. NetBT 4300 – The driver could not be created. WMI 10 - Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor" AND TargetInstance.LoadPercentage 99" could not be reactivated in namespace "//./root/CIMV2" because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected. More or less with timestamps it becomes apparent that the network maybe the issue. 1:25:57 - Group Policy is trying to discover the domain controller information 1:25:57 - The network link has been disconnected 1:25:58 - The processing of Group Policy failed because of lack of network connectivity to a domain controller. This may be a transient condition. A success message would be generated once the machine gets connected to the domain controller and Group Policy has successfully processed. If you do not see a success message for several hours, then contact your administrator. 1:25:58 - Making LDAP calls to connect and bind to active directory. DC1.ourdomain.edu 1:25:58 - Call failed after 0 milliseconds. 1:25:58 - Forcing rediscovery of domain controller details. 1:25:58 - Group policy failed to discover the domain controller in 1030 milliseconds 1:25:58 - Periodic policy processing failed for computer OURDOMAIN\%name%$ in 1 seconds. 1:25:59 - A network link has been established at 1Gbps at full duplex 1:26:00 - The network link has been disconnected 1:26:02 - NtpClient was unable to set a domain peer to use as a time source because of discovery error. NtpClient will try again in 3473457 minutes and DOUBLE THE REATTEMPT INTERVAL thereafter. 1:26:05 - A network link has been established at 1Gbps at full duplex 1:26:08 - Name resolution for the name %Name% timed out after none of the configured DNS servers responded. 1:26:10 – The TCP/IP NetBIOS Helper service entered the running state. 1:26:11 - The time provider NtpClient is currently receiving valid time data at dc4.ourdomain.edu 1:26:14 – User Logon Notification for Customer Experience Improvement Program 1:26:15 - Group Policy received the notification Logon from Winlogon for session 1. 1:26:15 - Making LDAP calls to connect and bind to Active Directory. dc4.ourdomain.edu 1:26:18 - The LDAP call to connect and bind to Active Directory completed. dc4. ourdomain.edu. The call completed in 2309 milliseconds. 1:26:18 - Group Policy successfully discovered the Domain Controller in 2918 milliseconds. 1:26:18 - Computer details: Computer role : 2 Network name : (Blank) 1:26:18 - The LDAP call to connect and bind to Active Directory completed. dc4.ourdomain.edu. The call completed in 2309 milliseconds. 1:26:18 - Group Policy successfully discovered the Domain Controller in 2918 milliseconds. 1:26:19 - The WinHTTP Web Proxy Auto-Discovery Service service entered the running state. 1:26:46 - The Network Connections service entered the running state. 1:27:10 – Retrieved account information 1:27:10 – The system call to get account information completed. 1:27:10 - Starting policy processing due to network state change for computer OURDOMAIN\%name%$ 1:27:10 – Network state change detected 1:27:10 - Making system call to get account information. 1:27:11 - Making LDAP calls to connect and bind to Active Directory. dc4.ourdomain.edu 1:27:13 - Computer details: Computer role : 2 Network name : ourdomain.edu (Now not blank) 1:27:13 - Group Policy successfully discovered the Domain Controller in 2886 milliseconds. 1:27:13 - The LDAP call to connect and bind to Active Directory completed. dc4.ourdomain.edu The call completed in 2371 milliseconds. 1:27:15 - Estimated network bandwidth on one of the connections: 0 kbps. 1:27:15 - Estimated network bandwidth on one of the connections: 8545 kbps. 1:27:15 - A fast link was detected. The Estimated bandwidth is 8545 kbps. The slow link threshold is 500 kbps. 1:27:17 – Powershell - Engine state is changed from Available to Stopped. 1:27:20 - Completed Group Policy Local Users and Groups Extension Processing in 4539 milliseconds. 1:27:25 - Completed Group Policy Scheduled Tasks Extension Processing in 5210 milliseconds. 1:27:27 - Completed Group Policy Registry Extension Processing in 1529 milliseconds. 1:27:27 - Completed policy processing due to network state change for computer OURDOMAIN\%name%$ in 16 seconds. 1:27:27 – The Group Policy settings for the computer were processed successfully. There were no changes detected since the last successful processing of Group Policy. Any help would be appreciated. Please ask for any relevant information and it will be provided as soon as possible.

  Read the article

• What is the advantage of WSDualHttpBinding in WCF?

  - by schmoopy

  How much benefit would there be to using WSDualHttpBinding with IIS hosted service vs. a client poll that calls the WCF service, assuming in the latter the service cached the data in question? This scenerio would be for a notify type of service where the clients need to be notified by the service when an event occurs. Specifically, what advantages would WSDualHttpBinding provide over polling? ie: Less network traffic, faster to design, easier to maintain, more control ??? From what i understand, WSDualHttpBinding is less scalable than client polling, so why use it at all? Edit: As Matt supplied, time critical can be one reason for the duplex binding. Here is what i have so far: WSDualHttpBinding adv: can get immediate response w/o waiting on polling timer dis: less scalable than WsHttpBinding dis: less firewall friendly I'll add to this based on comments, please let me know if i state anything incorrectly. thanks for you input :-)

  Read the article

• How does Facebook chat avoid continuous polling of the server?

  - by Chad Johnson

  I am trying to understand how Facebook's chat feature receives messages without continuously poling the server. Firebug shows me a single GET XmlHttpRequest continuously sitting there, waiting for a response from the server. After 5 minutes, this never timed out. How are they preventing timeout? An AJAX request can just sit there like that indefinitely, waiting for a response? Can I do this with JSONRequest? I see this at json.org: JSONRequest is designed to support duplex connections. This permits applications in which the server can asynchronously initiate transmissions. This is done by using two simultaneous requests: one to send and the other to receive. By using the timeout parameter, a POST request can be left pending until the server determines that it has timely data to send. Or is there another way to let an AJAX call just sit there, waiting, besides using JSONRequest?

  Read the article

• Is there any way, short of "copy and paste inheritence" to share a .net class with a Silverlight app

  - by Jekke

  I have a project in two parts: a Silverlight front end and a WCF duplex service. Ideally, I would like to pass a message of a custom type (call it TradeOffer) from the WCF service to be consumed by the Silverlight application. When I try to, I get an error that indicates I can't pass an object of an unknown type across the wire like that and that, maybe, I could do so if I used the InternalsVisibleTo attribute on the server component. I'm not sure if that would work in this environment and know it would be messy in development. I originally put the message definition in a library to be used by both the service and the client, but couldn't add a reference to the library from the Silverlight client (because it's not a Silverlight assembly.) Is there some way I can access the definition of a message class from both the Silverlight client that consumes it and the service that publishes it without using the InternalsVisibleTo attribute or should I write the application another way?

  Read the article

• How to convert thousands of PDF files to a single Postscript file in a specified order

  - by tggagne

  I've discovered multiple options for convert a few to serveral PDFs into Postscript, but many are command-line programs with command-line limitations (this application lives on .NET). Our application generates tens-of-thousands of PDFs that we need to send to a printer, except BEFORE the Postscript is printed we need to edit the Postscript to insert print command instructions (duplex, tray-pulls, highlight color, etc.) I think a perfect solution might allow us to write the PDFs to a stream, and simultaneously allow us to read the output stream so we may edit the Postscript before writing it to a file. Of course, if I must create the file first containing all 10,000 PDFs and edit it in an additional pass, I'm OK with that, too. I should mention that speed is important. I need to print 10,000 at a time, but need to keep the printers busy 24-hours/day.

  Read the article

• ImageMagick: Tiff to PDF from PHP

  - by Sheldon

  How can I convert 2 tiff images to PDF, I already knows how to get the image out of the DB, and I print it using echo and setting up the MIME type. But, right know I need to use a duplex printer option, so I need a way to generate a PDF from inside my PHP page, that PDF must containt both TIFF images (one per page) How can I do that? What do I need for php to work with that library. Thank you very much. EDIT: Is a self hosted app, I own the server (actually I'm using WAMP 2). I extract the images from the MySQL DB (stored using LONGBLOBS).

  Read the article

• How to get a reference to IDuplexChannel, IDuplexSessionChannel or IOutputChannel in Wcf

  - by wizlb

  I have a duplex Wcf service and I'd like to get a reference to IDuplexChannel, IDuplexSessionChannel or IOutputChannel so that I can use the non-blocking BeginSend method. On my server, inside of the handler for the initiating method I have the following (I have tried every interface that I listed in place of IOutputChannel. None of them seem to exist.) _clientCb = OperationContext.Current.GetCallbackChannel<IDxClientCb>(); _channel = OperationContext.Current.Channel; _duplexChannel = _channel as IOutputChannel; Debug.Print("Service IOutputChannel null: {0}", _duplexChannel == null); Similarly, in the client I have tried to cast the return value of DuplexChannelFactory.CreateChannel() to any of these interfaces and I always get back a null. How do I get a reference to one of these?

  Read the article

• Linux C: "Interactive session" with separate read and write named pipes?

  - by ~sd-imi

  Hi all, I am trying to work with "Introduction to Interprocess Communication Using Named Pipes - Full-Duplex Communication Using Named Pipes", http://developers.sun.com/solaris/articles/named_pipes.html#5 ; in particular fd_server.c (included below for reference) Here is my info and compile line: :~$ cat /etc/issue Ubuntu 10.04 LTS \n \l :~$ gcc --version gcc (Ubuntu 4.4.3-4ubuntu5) 4.4.3 :~$ gcc fd_server.c -o fd_server fd_server.c creates two named pipes, one for reading and one for writing. What one can do, is: in one terminal, run the server and read (through cat) its write pipe: :~$ ./fd_server & 2/dev/null [1] 11354 :~$ cat /tmp/np2 and in another, write (using echo) to server's read pipe: :~$ echo "heeellloooo" /tmp/np1 going back to first terminal, one can see: :~$ cat /tmp/np2 HEEELLLOOOO 0[1]+ Exit 13 ./fd_server 2 /dev/null What I would like to do, is make sort of a "interactive" (or "shell"-like) session; that is, the server is run as usual, but instead of running "cat" and "echo", I'd like to use something akin to screen. What I mean by that, is that screen can be called like screen /dev/ttyS0 38400, and then it makes a sort of a interactive session, where what is typed in terminal is passed to /dev/ttyS0, and its response is written to terminal. Now, of course, I cannot use screen, because in my case the program has two separate nodes, and as far as I can tell, screen can refer to only one. How would one go about to achieve this sort of "interactive" session in this context (with two separate read/write pipes)? Thanks, Cheers! Code below: #include <stdio.h> #include <errno.h> #include <ctype.h> #include <sys/types.h> #include <sys/stat.h> #include <fcntl.h> //#include <fullduplex.h> /* For name of the named-pipe */ #define NP1 "/tmp/np1" #define NP2 "/tmp/np2" #define MAX_BUF_SIZE 255 #include <stdlib.h> //exit #include <string.h> //strlen int main(int argc, char *argv[]) { int rdfd, wrfd, ret_val, count, numread; char buf[MAX_BUF_SIZE]; /* Create the first named - pipe */ ret_val = mkfifo(NP1, 0666); if ((ret_val == -1) && (errno != EEXIST)) { perror("Error creating the named pipe"); exit (1); } ret_val = mkfifo(NP2, 0666); if ((ret_val == -1) && (errno != EEXIST)) { perror("Error creating the named pipe"); exit (1); } /* Open the first named pipe for reading */ rdfd = open(NP1, O_RDONLY); /* Open the second named pipe for writing */ wrfd = open(NP2, O_WRONLY); /* Read from the first pipe */ numread = read(rdfd, buf, MAX_BUF_SIZE); buf[numread] = '0'; fprintf(stderr, "Full Duplex Server : Read From the pipe : %sn", buf); /* Convert to the string to upper case */ count = 0; while (count < numread) { buf[count] = toupper(buf[count]); count++; } /* * Write the converted string back to the second * pipe */ write(wrfd, buf, strlen(buf)); } Edit: Right, just to clarify - it seems I found a document discussing something very similar, it is http://en.wikibooks.org/wiki/Serial_Programming/Serial_Linux#Configuration_with_stty - a modification of the script there ("For example, the following script configures the device and starts a background process for copying all received data from the serial device to standard output...") for the above program is below: # stty raw # ( ./fd_server 2>/dev/null; )& bgPidS=$! ( cat < /tmp/np2 ; )& bgPid=$! # Read commands from user, send them to device echo $(kill -0 $bgPidS 2>/dev/null ; echo $?) while [ "$(kill -0 $bgPidS 2>/dev/null ; echo $?)" -eq "0" ] && read cmd; do # redirect debug msgs to stderr, as here we're redirected to /tmp/np1 echo "$? - $bgPidS - $bgPid" >&2 echo "$cmd" echo -e "\nproc: $(kill -0 $bgPidS 2>/dev/null ; echo $?)" >&2 done >/tmp/np1 echo OUT # Terminate background read process - if they still exist if [ "$(kill -0 $bgPid 2>/dev/null ; echo $?)" -eq "0" ] ; then kill $bgPid fi if [ "$(kill -0 $bgPidS 2>/dev/null ; echo $?)" -eq "0" ] ; then kill $bgPidS fi # stty cooked So, saving the script as say starter.sh and calling it, results with the following session: $ ./starter.sh 0 i'm typing here and pressing [enter] at end 0 - 13496 - 13497 I'M TYPING HERE AND PRESSING [ENTER] AT END 0~?.N=?(?~? ?????}????@??????~? [garble] proc: 0 OUT which is what I'd call for "interactive session" (ignoring the debug statements) - server waits for me to enter a command; it gives its output after it receives a command (and as in this case it exits after first command, so does the starter script as well). Except that, I'd like to not have buffered input, but sent character by character (meaning the above session should exit after first key press, and print out a single letter only - which is what I expected stty raw would help with, but it doesn't: it just kills reaction to both Enter and Ctrl-C :) ) I was just wandering if there already is an existing command (akin to screen in respect to serial devices, I guess) that would accept two such named pipes as arguments, and establish a "terminal" or "shell" like session through them; or would I have to use scripts as above and/or program own 'client' that will behave as a terminal..

  Read the article

• How many bits can be transfered through Ethernet at each time?

  - by Bobb

  I am writing a networking application. It has some unxpected lags. I need to calculate some figures but I cant find an information - how many bits can be transferes through Ethernet connection at each tick. I know that the resulting transfer rate is 100Mbps/1Gbps. But ethernet should use hardware ticks to sync both ends I suppose. So it moves data in ticks. So the question is how many ticks per second or how many bits per one tick used in ethernet. The actual connection is 100 Mbps full-duplex.

  Read the article

• Does TCP actually define 'TCP server' and 'TCP clients'? [closed]

  - by mjn

  In the Wikipedia article, TCP communication is explained using the terms 'client' and 'server'. It also uses the word 'peers'. But TCP actually does not define "TCP clients" and "TCP servers" - In the RFC 675 document (SPECIFICATION OF INTERNET TRANSMISSION CONTROL PROGRAM), the word "client" never appears. The RFC explains that TCP is used to connect processes over ports (sockets), and that 'A pair of sockets form a CONNECTION which can be used to carry data in either direction [i.e. full duplex]. Calling the originating party the "client" seems to be common practice. But this client/server communication model is not always applicable to TCP communication. For example take peer-to-peer networks. Calling all processes which open a socket (and wait for incoming connections from peers) "TCP servers", sounds wrong to me. I would not call my uncle's telephone device a "Telephony server" if I dial his phone number and he picks up.

  Read the article

• Silverlight Cream for March 29, 2010 -- #824

  - by Dave Campbell

  In this Issue: smartyP(-2-), Al Pascual, Mike Taulty, Shawn Burke(-2-), Vikram Pendse, Tomasz Janczuk, Lee, and Alexey Zakharov. Shoutouts: Jeff Weber announced New Silverlight Game “Snow Spill” by Nick Avery of Liserd Arts Games John Papa summarized links to all the Silverlight and Windows Phone 7 Sessions from MIX 10 Tim Heuer has a post up about OData and the MIX10 feed: MIX10: Yet another way to view video content sessions using their OData feed From SilverlightCream.com: Creating a Windows Phone 7 Metro Style Pivot Application [Part 1] smartyP has a two-part video tutorial up on creating a WP7 pivot navigation app using Expression Blend. He's also looking for feedback. Creating a Windows Phone 7 Metro Style Pivot Application [Part 2] In part 2, smartyP adds gestures to his navigation. He also has some good external links listed. Al Pascual: My First Windows Phone 7 Application Al Pascual extends the MIX10 keynote WP7 sample by adding the ability to send tweets ... with all the code. Silverlight 4 RC and the “silent installation” Mike Taulty discusses and demonstrates installing an OOB app without having to visit a webpage to get it. In other words, pass it around on a USB drive, send it in email, etc. iPhone SDK vs Windows Phone 7 Series SDK Challenge, Part 1: Hello World! Shawn Burke has a 2-part series up comparing iPhone and WP7 development looking at how easy it is to code and lines of code produced by the tools. This first post is the classic Hello World. Check out the comments as well. iPhone SDK vs. Windows Phone 7 Series SDK Challenge, Part 2: MoveMe Shawn Burke's part 2 is comparing the classic iPhone 'MoveMe' app... again, check out all the comments. Silverlight 4 : Indic Support in Silverlight Vikram Pendse demonstrates using the Microsoft Indic Language Input tool. He has some screen shots and discussion about fonts in Silverlight. Comparison of HTTP polling duplex and net.tcp performance in Silverlight 4 RC Tomasz Janczuk is checking out Silverlight4 RC and has a comparison up of the performance of the three mechanisms for asynch data push for the server to the client/. Summary rows in Datagrid with multiple groups Lee revisted a post that displayed Summary/Totals in the group header to also support multiple groups now. Silverlight Commands Hacks: Passing EventArgs as CommandParameter to DelegateCommand triggered by EventTrigger Alexey Zakharov suggests a workaround 'InvokeDelegateCommandAction' to keep Blend from ignoring event args. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• Silverlight Cream for March 10, 2010 - 2 -- #811

  - by Dave Campbell

  In this Issue: AfricanGeek, Phil Middlemiss, Damon Payne, David Anson, Jesse Liberty, Jeremy Likness, Jobi Joy(-2-), Fredrik Normén, Bobby Diaz, and Mike Taulty(-2-). Shoutouts: Shawn Wildermuth blogged that they posted My "What's New in Silverlight 3" Video from 0reDev Last Fall Shawn Wildermuth also has a post up for his loyal followers: Where to See Me At MIX10 Jonas Follesø has presentation materials up as well: MVVM presentation from NDC2009 on Vimeo Adam Kinney updated his Favorite Tool and Library Downloads for Silverlight From SilverlightCream.com: Styling Silverlight ListBox with Blend 3 In his latest Video Tutorial, AfricanGeek is animating the ListBox control by way of Expression Blend 3. Animating the Silverlight Opacity Mask Phil Middlemiss has written a Behavior that lets you turn a FrameworkElement into an opacity mask for it's parent container... check out his tutorial and grab the code. AddRange for ObservableCollection in Silverlight 3 Damon Payne has a post up discussing the problem with large amounts of data in an ObservableCollection, and how using AddRange is a performance booster. Easily rotate the axis labels of a Silverlight/WPF Toolkit chart David Anson blogged a solution to rotating the axis labels of a Silverlight and WPF chart. Persisting the Configuration (Updated) Jesse Liberty has a good discussion on the continuation of his HyperVideo Platform talking about what all he is needing from the database in the form of configuration information... including the relationships. Animations and View Models: IAnimationDelegate Check out Jeremy Likness' IAnimationDelegate that lets your ViewModel fire and respond to animations without having to know all about them. Button Style - Silverlight Jobi Joy converted a WPF control template into Silverlight... and you'll want to download the XAML he's got for this :) A Simple Accordion banner using ListBox Jobi Joy also has an Image Accordian created in Expression Blend... and it's a 'drop this XAML in your User Control' kinda thing... again, go grab the XAML :) WCF RIA Services Silverlight Business Application – Using ASP.NET SiteMap for Navigation Fredrik Normén has a code-laden post up on RIA Services and the ASP.NET SiteMap. He is using the Silverlight Business app template that comes with WCF RIA Services. A Simple, Selectable Silverlight TextBlock (sort of)... Bobby Diaz shares with us his solution for a Text control that can be copied from in the same manner 'normal' web controls can be. He also includes a link to another post on the same topic. Silverlight 4 Beta Networking. Part 11 - WCF and TCP Mike Taulty has another pair of video tutorials up in his Networking series. This one is on WCF over TCP Silverlight 4 Beta Networking. Part 12 - WCF and Polling HTTP Mike Taulty's 12th networking video tutorial is on WCF with HTTP polling duplex. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    MIX10

  Read the article

• Frequent Disconnects ubuntu desktop 12.10 x64 intel 82579V e1000e

  - by user112055

  I'm having frequent disconnects with my new install of Ubuntu 12.10. I tried updating the kernel driver to the latest intel release to no avail. My expertise is spent. It happens anywhere between 1 min and 10 min. Any ideas? syslog: Dec 1 13:51:39 andromeda kernel: [ 972.188809] audit_printk_skb: 6 callbacks suppressed Dec 1 13:51:39 andromeda kernel: [ 972.188813] type=1701 audit(1354398699.418:199): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188817] type=1701 audit(1354398699.418:200): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188820] type=1701 audit(1354398699.418:201): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188823] type=1701 audit(1354398699.418:202): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188825] type=1701 audit(1354398699.418:203): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.331419] type=1701 audit(1354398699.558:204): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=2 compat=0 ip=0x7f26777d96b0 code=0x50000 Dec 1 13:53:12 andromeda NetworkManager[1115]: <info> (eth0): carrier now OFF (device state 100, deferring action for 4 seconds) Dec 1 13:53:12 andromeda kernel: [ 1064.894387] e1000e: e1000e: eth0 NIC Link is Down Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> (eth0): device state change: activated -> unavailable (reason 'carrier-changed') [100 20 40] Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> (eth0): deactivating device (reason 'carrier-changed') [40] Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> (eth0): canceled DHCP transaction, DHCP client pid 5946 Dec 1 13:53:16 andromeda avahi-daemon[890]: Withdrawing address record for fe80::ea40:f2ff:fee2:4d86 on eth0. Dec 1 13:53:16 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:53:16 andromeda avahi-daemon[890]: Interface eth0.IPv6 no longer relevant for mDNS. Dec 1 13:53:16 andromeda kernel: [ 1069.025288] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Dec 1 13:53:16 andromeda avahi-daemon[890]: Withdrawing address record for 192.168.11.17 on eth0. Dec 1 13:53:16 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:53:16 andromeda avahi-daemon[890]: Interface eth0.IPv4 no longer relevant for mDNS. Dec 1 13:53:16 andromeda NetworkManager[1115]: <warn> DNS: plugin dnsmasq update failed Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> ((null)): removing resolv.conf from /sbin/resolvconf Dec 1 13:53:16 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:53:16 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:53:16 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): carrier now ON (device state 20) Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Auto-activating connection '82579V'. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) starting connection '82579V' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Dec 1 13:53:32 andromeda kernel: [ 1084.938042] e1000e: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx Dec 1 13:53:32 andromeda kernel: [ 1084.938049] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO Dec 1 13:53:32 andromeda kernel: [ 1084.938815] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> dhclient started with pid 6080 Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Dec 1 13:53:32 andromeda dhclient: Internet Systems Consortium DHCP Client 4.2.4 Dec 1 13:53:32 andromeda dhclient: Copyright 2004-2012 Internet Systems Consortium. Dec 1 13:53:32 andromeda dhclient: All rights reserved. Dec 1 13:53:32 andromeda dhclient: For info, please visit https://www.isc.org/software/dhcp/ Dec 1 13:53:32 andromeda dhclient: Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed nbi -> preinit Dec 1 13:53:32 andromeda dhclient: Listening on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:53:32 andromeda dhclient: Sending on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:53:32 andromeda dhclient: Sending on Socket/fallback Dec 1 13:53:32 andromeda dhclient: DHCPREQUEST of 192.168.11.17 on eth0 to 255.255.255.255 port 67 Dec 1 13:53:32 andromeda dhclient: DHCPACK of 192.168.11.17 from 192.168.11.1 Dec 1 13:53:32 andromeda dhclient: bound to 192.168.11.17 -- renewal in 33576 seconds. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed preinit -> reboot Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> address 192.168.11.17 Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> prefix 24 (255.255.255.0) Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> gateway 192.168.11.1 Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> hostname 'andromeda' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> nameserver '192.168.11.1' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> domain name 'hsd1.ca.comcast.net' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Dec 1 13:53:32 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:53:32 andromeda avahi-daemon[890]: New relevant interface eth0.IPv4 for mDNS. Dec 1 13:53:32 andromeda avahi-daemon[890]: Registering new address record for 192.168.11.17 on eth0.IPv4. Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> (eth0): device state change: ip-config -> activated (reason 'none') [70 100 0] Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> ((null)): writing resolv.conf to /sbin/resolvconf Dec 1 13:53:33 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:53:33 andromeda dnsmasq[1907]: using nameserver 192.168.11.1#53 Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> Policy set '82579V' (eth0) as default for IPv4 routing and DNS. Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> Activation (eth0) successful, device activated. Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Dec 1 13:53:33 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:53:33 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:53:33 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:53:33 andromeda avahi-daemon[890]: New relevant interface eth0.IPv6 for mDNS. Dec 1 13:53:33 andromeda avahi-daemon[890]: Registering new address record for fe80::ea40:f2ff:fee2:4d86 on eth0.*. Dec 1 13:53:41 andromeda ntpdate[6154]: adjust time server 91.189.94.4 offset 0.000928 sec Dec 1 13:53:50 andromeda NetworkManager[1115]: <info> (eth0): carrier now OFF (device state 100, deferring action for 4 seconds) Dec 1 13:53:50 andromeda kernel: [ 1102.980003] e1000e: e1000e: eth0 NIC Link is Down Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> (eth0): device state change: activated -> unavailable (reason 'carrier-changed') [100 20 40] Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> (eth0): deactivating device (reason 'carrier-changed') [40] Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> (eth0): canceled DHCP transaction, DHCP client pid 6080 Dec 1 13:53:54 andromeda avahi-daemon[890]: Withdrawing address record for fe80::ea40:f2ff:fee2:4d86 on eth0. Dec 1 13:53:54 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:53:54 andromeda avahi-daemon[890]: Interface eth0.IPv6 no longer relevant for mDNS. Dec 1 13:53:54 andromeda avahi-daemon[890]: Withdrawing address record for 192.168.11.17 on eth0. Dec 1 13:53:54 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:53:54 andromeda kernel: [ 1107.025959] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Dec 1 13:53:54 andromeda NetworkManager[1115]: <warn> DNS: plugin dnsmasq update failed Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> ((null)): removing resolv.conf from /sbin/resolvconf Dec 1 13:53:54 andromeda avahi-daemon[890]: Interface eth0.IPv4 no longer relevant for mDNS. Dec 1 13:53:54 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:53:54 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:53:54 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): carrier now ON (device state 20) Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Auto-activating connection '82579V'. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) starting connection '82579V' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Dec 1 13:54:10 andromeda kernel: [ 1123.167668] e1000e: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx Dec 1 13:54:10 andromeda kernel: [ 1123.167675] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO Dec 1 13:54:10 andromeda kernel: [ 1123.168430] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> dhclient started with pid 6212 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Dec 1 13:54:10 andromeda dhclient: Internet Systems Consortium DHCP Client 4.2.4 Dec 1 13:54:10 andromeda dhclient: Copyright 2004-2012 Internet Systems Consortium. Dec 1 13:54:10 andromeda dhclient: All rights reserved. Dec 1 13:54:10 andromeda dhclient: For info, please visit https://www.isc.org/software/dhcp/ Dec 1 13:54:10 andromeda dhclient: Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed nbi -> preinit Dec 1 13:54:10 andromeda dhclient: Listening on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:54:10 andromeda dhclient: Sending on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:54:10 andromeda dhclient: Sending on Socket/fallback Dec 1 13:54:10 andromeda dhclient: DHCPREQUEST of 192.168.11.17 on eth0 to 255.255.255.255 port 67 Dec 1 13:54:10 andromeda dhclient: DHCPACK of 192.168.11.17 from 192.168.11.1 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed preinit -> reboot Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> address 192.168.11.17 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> prefix 24 (255.255.255.0) Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> gateway 192.168.11.1 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> hostname 'andromeda' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> nameserver '192.168.11.1' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> domain name 'hsd1.ca.comcast.net' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Dec 1 13:54:10 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:54:10 andromeda dhclient: bound to 192.168.11.17 -- renewal in 35416 seconds. Dec 1 13:54:10 andromeda avahi-daemon[890]: New relevant interface eth0.IPv4 for mDNS. Dec 1 13:54:10 andromeda avahi-daemon[890]: Registering new address record for 192.168.11.17 on eth0.IPv4. Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> (eth0): device state change: ip-config -> activated (reason 'none') [70 100 0] Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> ((null)): writing resolv.conf to /sbin/resolvconf Dec 1 13:54:11 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:54:11 andromeda dnsmasq[1907]: using nameserver 192.168.11.1#53 Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> Policy set '82579V' (eth0) as default for IPv4 routing and DNS. Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> Activation (eth0) successful, device activated. Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Dec 1 13:54:11 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:54:11 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:54:12 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:54:12 andromeda avahi-daemon[890]: New relevant interface eth0.IPv6 for mDNS. Dec 1 13:54:12 andromeda avahi-daemon[890]: Registering new address record for fe80::ea40:f2ff:fee2:4d86 on eth0.*. Dec 1 13:54:19 andromeda ntpdate[6286]: adjust time server 91.189.94.4 offset 0.001142 sec $ lspci -v 00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 04) Subsystem: Intel Corporation Device 2031 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at f7f00000 (32-bit, non-prefetchable) [size=128K] Memory at f7f39000 (32-bit, non-prefetchable) [size=4K] I/O ports at f040 [size=32] Capabilities: [c8] Power Management version 2 Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [e0] PCI Advanced Features Kernel driver in use: e1000e Kernel modules: e1000e $ modinfo e1000e filename: /lib/modules/3.5.0-19-generic/kernel/drivers/net/e1000e/e1000e.ko version: 2.1.4-NAPI license: GPL description: Intel(R) PRO/1000 Network Driver author: Intel Corporation, <[email protected]> srcversion: 0809529BE0BBC44883956AF alias: pci:v00008086d0000153Bsv*sd*bc*sc*i* alias: pci:v00008086d0000153Asv*sd*bc*sc*i* alias: pci:v00008086d00001503sv*sd*bc*sc*i* alias: pci:v00008086d00001502sv*sd*bc*sc*i* alias: pci:v00008086d000010F0sv*sd*bc*sc*i* alias: pci:v00008086d000010EFsv*sd*bc*sc*i* alias: pci:v00008086d000010EBsv*sd*bc*sc*i* alias: pci:v00008086d000010EAsv*sd*bc*sc*i* alias: pci:v00008086d00001525sv*sd*bc*sc*i* alias: pci:v00008086d000010DFsv*sd*bc*sc*i* alias: pci:v00008086d000010DEsv*sd*bc*sc*i* alias: pci:v00008086d000010CEsv*sd*bc*sc*i* alias: pci:v00008086d000010CDsv*sd*bc*sc*i* alias: pci:v00008086d000010CCsv*sd*bc*sc*i* alias: pci:v00008086d000010CBsv*sd*bc*sc*i* alias: pci:v00008086d000010F5sv*sd*bc*sc*i* alias: pci:v00008086d000010BFsv*sd*bc*sc*i* alias: pci:v00008086d000010E5sv*sd*bc*sc*i* alias: pci:v00008086d0000294Csv*sd*bc*sc*i* alias: pci:v00008086d000010BDsv*sd*bc*sc*i* alias: pci:v00008086d000010C3sv*sd*bc*sc*i* alias: pci:v00008086d000010C2sv*sd*bc*sc*i* alias: pci:v00008086d000010C0sv*sd*bc*sc*i* alias: pci:v00008086d00001501sv*sd*bc*sc*i* alias: pci:v00008086d00001049sv*sd*bc*sc*i* alias: pci:v00008086d0000104Dsv*sd*bc*sc*i* alias: pci:v00008086d0000104Bsv*sd*bc*sc*i* alias: pci:v00008086d0000104Asv*sd*bc*sc*i* alias: pci:v00008086d000010C4sv*sd*bc*sc*i* alias: pci:v00008086d000010C5sv*sd*bc*sc*i* alias: pci:v00008086d0000104Csv*sd*bc*sc*i* alias: pci:v00008086d000010BBsv*sd*bc*sc*i* alias: pci:v00008086d00001098sv*sd*bc*sc*i* alias: pci:v00008086d000010BAsv*sd*bc*sc*i* alias: pci:v00008086d00001096sv*sd*bc*sc*i* alias: pci:v00008086d0000150Csv*sd*bc*sc*i* alias: pci:v00008086d000010F6sv*sd*bc*sc*i* alias: pci:v00008086d000010D3sv*sd*bc*sc*i* alias: pci:v00008086d0000109Asv*sd*bc*sc*i* alias: pci:v00008086d0000108Csv*sd*bc*sc*i* alias: pci:v00008086d0000108Bsv*sd*bc*sc*i* alias: pci:v00008086d0000107Fsv*sd*bc*sc*i* alias: pci:v00008086d0000107Esv*sd*bc*sc*i* alias: pci:v00008086d0000107Dsv*sd*bc*sc*i* alias: pci:v00008086d000010B9sv*sd*bc*sc*i* alias: pci:v00008086d000010D5sv*sd*bc*sc*i* alias: pci:v00008086d000010DAsv*sd*bc*sc*i* alias: pci:v00008086d000010D9sv*sd*bc*sc*i* alias: pci:v00008086d00001060sv*sd*bc*sc*i* alias: pci:v00008086d000010A5sv*sd*bc*sc*i* alias: pci:v00008086d000010BCsv*sd*bc*sc*i* alias: pci:v00008086d000010A4sv*sd*bc*sc*i* alias: pci:v00008086d0000105Fsv*sd*bc*sc*i* alias: pci:v00008086d0000105Esv*sd*bc*sc*i* depends: vermagic: 3.5.0-19-generic SMP mod_unload modversions parm: copybreak:Maximum size of packet that is copied to a new buffer on receive (uint) parm: TxIntDelay:Transmit Interrupt Delay (array of int) parm: TxAbsIntDelay:Transmit Absolute Interrupt Delay (array of int) parm: RxIntDelay:Receive Interrupt Delay (array of int) parm: RxAbsIntDelay:Receive Absolute Interrupt Delay (array of int) parm: InterruptThrottleRate:Interrupt Throttling Rate (array of int) parm: IntMode:Interrupt Mode (array of int) parm: SmartPowerDownEnable:Enable PHY smart power down (array of int) parm: KumeranLockLoss:Enable Kumeran lock loss workaround (array of int) parm: CrcStripping:Enable CRC Stripping, disable if your BMC needs the CRC (array of int) parm: EEE:Enable/disable on parts that support the feature (array of int) parm: Node:[ROUTING] Node to allocate memory on, default -1 (array of int) parm: debug:Debug level (0=none,...,16=all) (int)

  Read the article

• Why does my MySQL remote-connection fail (VLAN)?

  - by Johannes Nielsen

  ubuntu-community! Again I have a problem with my special friend MySQL :D I have got two servers - a database-server and a web-server - who are connected via VLAN. Now I want the web-server to have remote access to the database-server's MySQL. So I created the user user in mysql.user. user's Host is xxx.yyy.zzz.9 which is the internal IP-address of the web-server. xxx.yyy.zzz.0 is the network. I also created user with Host % . As long as I use MySQL on the database-server logging in as user, everything works fine. But trying to log in as user from xxx.yyy.zzz.9 using mysql -h xxx.yyy.zzz.8 -u user -p (where xxx.yyy.zzz.8 is the database-server's internal IP), I get ERROR 2003 (HY000): Can't connect to MySQL server on 'xxx.yyy.zzz.8' (110) So I tried to activate Bind-Address in the my.cnf file. Well, if I use xxx.yyy.zzz.8, nothing changes. But if I try xxx.yyy.zzz.9 and try to restart MySQL, I get mysql stop/waiting start: Job failed to start I checked the log files and found - nothing. The database-server's MySQL doesn't even register, that the web-server tries to connect remotely. My idea is, that maybe I didn't configure the VLAN properley, even though I asked someone who actually knows such stuff and he told me, I did everything right. What I wrote into /etc/networking/interfaces is: #The VLAN auto eth1 iface eth1 inet static address xxx.yyy.zzz..8 netmask 255.255.255.0 network xxx.yyy.zzz.0 broadcast xxx.yyy.zzz.255 mtu 1500 ifconfig returns eth1 Link encap:Ethernet HWaddr xxxxxxxxxxxxxx inet addr:xxx.yyy.zzz.8 Bcast:xxx.yyy.zzz.255 Mask:255.255.255.0 inet6 addr: xxxxxxxxxxxxxxx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:241146 errors:0 dropped:0 overruns:0 frame:0 TX packets:9765 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17825995 (17.8 MB) TX bytes:566602 (566.6 KB) Memory:fb900000-fb920000 for the eth1, what is, what I configured. (This is for the database-server, the web-server looks similar). ethtool eth1 returns: Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000003 (3) drv probe Link detected: yes (This is for the database-server, the web-server looks similar). Actually I think, everything is right, but it still doesn't work. Is there someone with an idea? EDIT: I commented ou Bind-Address in my.cnf after it didn't work.

  Read the article

• ath9k driver does not weak up

  - by shantanu

  I know this is common question but i found no suitable answer, so i am asking this again. I installed ubuntu 11.10. I found the bug for ath9k, so set first network boot from BIOS menu. That's worked. I have upgraded to 12.04 yesterday. Now ath9k is creating problem again. First network boot is still enable. ath9k works at start. But failed(connect again and again) after couple of minutes. dmesg show error that it can not weak up in 500us. So i tried #compat-wireless-3.5.1-1. But result is same. I have also added #nohwcrypt=1 option in /etc/modeprob.d/ath9k.conf. Still no luck. I tried #rmmod and then modprobe sudo modprobe ath9k nohwcrypt=1 dmesg shows me error: [ 400.690086] ath9k: Driver unloaded [ 406.214329] ath9k 0000:06:00.0: enabling device (0000 -> 0002) [ 406.214348] ath9k 0000:06:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 406.214368] ath9k 0000:06:00.0: setting latency timer to 64 [ 406.428517] ath9k 0000:06:00.0: Failed to initialize device [ 406.428852] ath9k 0000:06:00.0: PCI INT A disabled [ 406.428887] ath9k: probe of 0000:06:00.0 failed with error -5 dmesg error when driver fail: 355.023521] ath: Chip reset failed [ 355.023524] ath: Unable to reset channel, reset status -22 [ 355.023556] ath: Unable to set channel [ 355.088569] ath: Failed to stop TX DMA, queues=0x10f! [ 355.122708] ath: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff [ 355.122714] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up [ 355.263962] ath: Chip reset failed [ 355.263966] ath: Unable to reset channel (2437 MHz), reset status -22 [ 358.996063] ath: Failed to wakeup in 500us [ 364.004182] ath: Failed to wakeup in 500us I can not install fresh ubuntu because i have lots of application installed. System : Acer Aspire 4250 AMD dual core 1.6GHZ Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) EDITED Now i am in serious problem. No wifi device is not showing in ifconfig or lshw commands. Only ether-net interface shows. I tried (FN + WIFI) several times to enable the device but nothing helps. Now I have installed fresh ubuntu 12.04. Please help lshw -c network: *-network description: Ethernet interface product: 82566DC Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 02 serial: 00:19:d1:7a:8e:f9 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=2.0.0-k duplex=full firmware=1.1-0 ip=192.168.1.114 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:90300000-9031ffff memory:90324000-90324fff ioport:20c0(size=32) rfkill command does not show anything but no error.

  Read the article

• Atheros AR9285 / Lenovo G560 wireless not working after installing 13.04

  - by teyi

  I had Ubuntu 12.04 initially installed on my laptop. I upgraded to 12.10 then 13.04. Everything worked fine, including wireless. After adding a new memory card ( I only had 2 gb and one memory slot free) my wireess stopped working. I backed up all my data and reinstallled Ubuntu 13.04. Everything works fine except wireess. I bought this laptop in 2010 from Japan. It has Intel Core i5 CPU M 450 @2.40 Ghz * 4 3,7 Gb RAM os type 64 bit The output of iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off The output of rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no The output of lshw -C network: *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:05:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:7d:fe:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.8.0-19-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d6400000-d640ffff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 02 serial: 88:ae:1d:2b:36:ac size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d2410000-d2410fff memory:d2400000-d240ffff memory:d2420000-d243ffff The wi-fi network appears as disconnected ( it's greyed out) Strangely enough I see a wifi network ( not mine) but not mine or the rest. That network doesn't require a password . I click on it, try to connect and i get an error message: failed to connect to xxxxx ... 32) The access point/org/freedesktop/NetworkManager/AccessPoint/0 was not in the scan list. Someone help please

  Read the article

• wifi problems with lenovo g580 on kubuntu-13.04-desktop-amd64

  - by user203963

  i have a wifi connection problem in lenovo g580 on kubuntu-13.04-desktop-amd64. ethernet cable is working properly but wifi does'nt connect below are some hardware information sudo lshw -class network gives *-network description: Ethernet interface product: AR8162 Fast Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:89:84:3d:e9:10 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm pciexpress msi msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=alx driverversion=1.2.3 duplex=full firmware=N/A ip=192.168.0.106 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:90500000-9053ffff ioport:2000(size=128) *-network description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=bcma-pci-bridge latency=0 resources: irq:17 memory:90400000-90403fff *-network description: Wireless interface physical id: 3 logical name: wlan0 serial: 68:94:23:fa:2c:d9 capabilities: ethernet physical wireless configuration: broadcast=yes driver=brcmsmac driverversion=3.8.0-19-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bgn lsubs gives Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0489:e032 Foxconn / Hon Hai Bus 002 Device 003: ID 04f2:b2e2 Chicony Electronics Co., Ltd lspci gives 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) 00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04) 01:00.0 Ethernet controller: Qualcomm Atheros AR8162 Fast Ethernet (rev 10) 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Does anyone knows the solution? rfkill list all gives 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: yes Hard blocked: no 2: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 3: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no

  Read the article

• RealTek RTL8188CE WiFi adapter doesn't connect reliably

  - by ken.ganong

  I recently bought a new system76 laptop which came pre-installed with Ubuntu 11.10. I've been having trouble with my wireless connectivity. It seems that my connection with my wireless network keeps going in and out. It is not my network--I have seen the same problem on multiple WiFi networks and at different distances and reported link qualities. OS version: Ubuntu 11.10 oneiric kernel version: 3.0.0-14-generic lspci: lspci -nnk | grep -iA2 net 04:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:9196] Kernel driver in use: rtl8192ce -- 05:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) Subsystem: CLEVO/KAPOK Computer Device [1558:2500] Kernel driver in use: jme iwconfig: iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"peppermintpatty" Mode:Managed Frequency:2.462 GHz Access Point: 98:FC:11:6C:E0:22 Bit Rate=72.2 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Power Management:off Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:1103 Missed beacon:0 lshw: sudo lshw -class network *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 00:1c:7b:a1:95:04 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.0.0-14-generic firmware=N/A ip=192.168.1.106 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:18 ioport:e000(size=256) memory:f7d00000-f7d03fff *-network description: Ethernet interface product: JMC250 PCI Express Gigabit Ethernet Controller vendor: JMicron Technology Corp. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 00:90:f5:c0:42:b3 size: 10Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:56 memory:f7c20000-f7c23fff ioport:d100(size=128) ioport:d000(size=256) memory:f7c10000-f7c1ffff memory:f7c00000-f7c0ffff Any help would be appreciated. The last time I've dealt with wireless issues, the most given solution was NDIS wrapper and I seem sorely out-of-date.

  Read the article

• How do I get wireless working on a Dell Inspiron 510m?

  - by user17449

  Why WiFi don't work in my Dell Inspiron 510m with Ubuntu 10.04? Is that usefull? inspiron@Inspiron:~$ rfkill list all inspiron@Inspiron:~$ sudo lshw -C network [sudo] password for inspiron: *-network:0 DISABLED description: Wireless interface product: PRO/Wireless LAN 2100 3B Mini PCI Adapter vendor: Intel Corporation physical id: 3 bus info: pci@0000:01:03.0 logical name: eth1 version: 04 serial: 00:0c:f1:5b:5d:40 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ipw2100 driverversion=git-1.2.2 firmware=712.0.3:3:00000001 latency=32 link=no maxlatency=34 mingnt=2 multicast=yes wireless=unassociated resources: irq:5 memory:fcffe000-fcffefff *-network:1 description: Ethernet interface product: 82801DB PRO/100 VE (MOB) Ethernet Controller vendor: Intel Corporation physical id: 8 bus info: pci@0000:01:08.0 logical name: eth0 version: 81 serial: 00:11:43:41:d8:b8 size: 10MB/s capacity: 100MB/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half firmware=N/A ip=192.168.0.2 latency=32 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10MB/s resources: irq:11 memory:fcffd000-fcffdfff ioport:ecc0(size=64) inspiron@Inspiron:~$ iwconfig wlan0 wlan0 No such device inspiron@Inspiron:~$ ifconfig -a eth0 Link encap:Ethernet Endereço de HW 00:11:43:41:d8:b8 inet end.: 192.168.0.2 Bcast:192.168.0.255 Masc:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet Endereço de HW 00:0c:f1:5b:5d:40 BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) IRQ:5 Endereço de E/S:0xe000 Memória:fcffe000-fcffefff lo Link encap:Loopback Local inet end.: 127.0.0.1 Masc:255.0.0.0 endereço inet6: ::1/128 Escopo:Máquina UP LOOPBACK RUNNING MTU:16436 Métrica:1 pacotes RX:628 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:628 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:0 RX bytes:50104 (50.1 KB) TX bytes:50104 (50.1 KB) inspiron@Inspiron:~$ nm-tool NetworkManager Tool State: connected - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: ipw2100 State: unavailable Default: no HW Address: 00:0C:F1:5B:5D:40 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: e100 State: unmanaged Default: no HW Address: 00:11:43:41:D8:B8 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: off inspiron@Inspiron:~$

  Read the article

• Wifi disabled for Intel Centrino Wireless-N 1000 Intel in 12.04

  - by new_bie

  Laptop model - HP- dm4 - 2070. I had faced the same problem for wireless being disabled in case of 11.10. It had to do with the new kernel. I thought with 12.04 this problem will be handled but the problem persists. Is there no way to get the wireless working except for the way mentioned in the following link ?? Wifi for Centrino Wireless-N 1000 Intel Corporation (HP pavillion dm4 - 2070us) is not working Output for sudo lshw -class network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress cap_list configuration: latency=0 resources: memory:c2500000-c2501fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: c0 serial: 2c:41:38:07:f3:e3 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.116 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:c1400000-c143ffff ioport:2000(size=128) Output for dmesg | grep iwl [ 14.742886] iwlwifi 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 14.742897] iwlwifi 0000:01:00.0: setting latency timer to 64 [ 14.743013] iwlwifi 0000:01:00.0: pci_resource_len = 0x00002000 [ 14.743016] iwlwifi 0000:01:00.0: pci_resource_base = ffffc90000c78000 [ 14.743018] iwlwifi 0000:01:00.0: HW Revision ID = 0x0 [ 14.743119] iwlwifi 0000:01:00.0: irq 42 for MSI/MSI-X [ 14.743161] iwlwifi 0000:01:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 14.743229] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S [ 14.765147] iwlwifi 0000:01:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 14.765151] iwlwifi 0000:01:00.0: Device SKU: 0X50 [ 14.765154] iwlwifi 0000:01:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 14.765907] iwlwifi 0000:01:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 14.912840] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-5.ucode' failed. [ 14.914254] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-4.ucode' failed. [ 14.915718] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-3.ucode' failed. [ 14.916986] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-2.ucode' failed. [ 14.919391] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-1.ucode' failed. [ 14.919445] iwlwifi 0000:01:00.0: no suitable firmware found! [ 14.919783] iwlwifi 0000:01:00.0: PCI INT A disabled [ 2868.960807] Modules linked in: snd_hda_codec_hdmi snd_hda_codec_idt rfcomm bnep bluetooth parport_pc ppdev binfmt_misc hid_logitech_dj usbhid hid joydev snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq hp_wmi sparse_keymap hp_accel lis3lv02d input_polldev snd_timer snd_seq_device wmi iwlwifi snd mac80211 i915 cfg80211 rts_pstor(C) drm_kms_helper drm uvcvideo videodev psmouse soundcore mei(C) v4l2_compat_ioctl32 mac_hid serio_raw snd_page_alloc i2c_algo_bit video lp parport atl1c

  Read the article

• Wireless not working on Dell Inspirion 1501 after upgrading to Ubuntu 12.04 tried steps in other threads

  - by mark burton

  I updated to Ubuntu 12.04 and now my wireless is not working. No icon for it. Tried some of the troubleshooting in other threads but can't get it to work. Would really appreciate any help Thanks! " *-network description: Network controller product: BCM4311 802.11a/b/g vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:c0200000-c0203fff *-network description: Ethernet interface product: BCM4401-B0 100Base-TX vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 02 serial: 00:19:b9:5c:d1:52 size: 100Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=full ip=10.0.0.6 latency=64 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:21 memory:c0300000-c0301fff " lsub results Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c526 Logitech, Inc. Nano Receiver $ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI RS480 Host Bridge (rev 10) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:05.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:06.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS482 [Radeon Xpress 200M] 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01) 08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 08:01.0 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 08:01.1 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 01) rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• What are these errors when I try to "make" the driver of my wireless adapter?

  - by Tom Brito

  I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

  Read the article

• Intel Centrino Wireless N 1000 doesn't work on a Lenovo Z560

  - by Timetraveler

  I upgraded my Ubuntu 11.04 to 11.10 and my Wifi has stopped working. I have a Lenovo Z560 that has Intel centrino wireless-N 1000. I have searched various threads having similar problems for a solution and have no success. The wlan0 is not even showing up in rfkill. Please help me find a solution. I am giving below the output of various debug commands. Thanks in advance. DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" ----##uname -a Linux gurucharapathy-laptop 3.0.0-17-generic-pae #30-Ubuntu SMP Thu Mar 8 17:53:35 UTC 2012 i686 i686 i386 GNU/Linux ----##lspci -nnk | grep -iA2 net 05:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1000 [8086:0084] Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN [8086:1315] Kernel modules: iwlagn 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) Subsystem: Lenovo Device [17aa:392e] Kernel driver in use: r8169 ----##iwconfig lo no wireless extensions. eth0 no wireless extensions. ----##iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. ----##rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no ----##lsmod Module Size Used by rfcomm 38408 8 bnep 17923 2 parport_pc 32114 0 ppdev 12849 0 binfmt_misc 17292 1 snd_hda_codec_hdmi 31426 1 snd_hda_codec_conexant 52460 1 uvcvideo 67271 0 videodev 85626 1 uvcvideo snd_hda_intel 28358 2 snd_hda_codec 91859 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec joydev 17393 0 snd_pcm 80435 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 i915 509554 9 drm_kms_helper 32889 1 i915 snd_rawmidi 25241 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28932 2 snd_pcm,snd_seq drm 196290 5 i915,drm_kms_helper snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq mei 36466 0 mac80211 393421 0 snd 55902 14 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 13575 0 intel_ips 17753 0 btusb 18160 2 i2c_algo_bit 13199 1 i915 soundcore 12600 1 snd bluetooth 148839 23 rfcomm,bnep,btusb cfg80211 172427 1 mac80211 psmouse 63474 0 serio_raw 12990 0 snd_page_alloc 14108 2 snd_hda_intel,snd_pcm sparse_keymap 13658 1 ideapad_laptop wmi 18744 0 video 18908 1 i915 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp ahci 21634 2 libahci 25761 1 ahci r8169 47200 0 ----##nm-tool NetworkManager Tool State: asleep Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: r8169 State: unmanaged Default: no HW Address: 88:AE:1D:DE:5F:9C Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on ----##lshw -C network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d6400000-d6401fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 02 serial: 88:ae:1d:de:5f:9c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=192.168.0.100 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d2410000-d2410fff memory:d2400000-d240ffff memory:d2420000-d243ffff

  Read the article

• What are these errors when I try to "make" the driver of my wireless network?

  - by Tom Brito

  I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme file say to use the "make" command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

  Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >