Search Results

Search found 1882 results on 76 pages for 'gnu'.

Page 62/76 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

• ubuntu dmidecode is not functioning properly

  - by Alaa Alomari

  dmidecode is giving irrelevant and conflicted results. it shows that i have two slots while the correct is 8 (the board is Tyan S5350.) uname -a Linux synd01 3.0.0-16-server #29-Ubuntu SMP Tue Feb 14 13:08:12 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux root@synd01:/home/badmin# dmidecode -t 16 dmidecode 2.9 SMBIOS 2.33 present. Handle 0x0011, DMI type 16, 15 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: None Maximum Capacity: 4 GB Error Information Handle: Not Provided Number Of Devices: 2 while root@synd01:/home/badmin# dmidecode -t 17 | grep Size Size: No Module Installed Size: No Module Installed Size: 1024 MB Size: 1024 MB Size: No Module Installed Size: No Module Installed Size: 1024 MB Size: 1024 MB also lshw shows: *-memory description: System Memory physical id: 11 slot: System board or motherboard size: 4GiB *-bank:0 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 0 slot: J3B1 clock: 166MHz (6.0ns) *-bank:1 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 1 slot: J3B3 clock: 166MHz (6.0ns) *-bank:2 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 2 slot: J2B2 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:3 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 3 slot: J2B4 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:4 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 4 slot: J3B2 clock: 166MHz (6.0ns) *-bank:5 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 5 slot: J2B1 clock: 166MHz (6.0ns) *-bank:6 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 6 slot: J2B3 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:7 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 7 slot: J1B1 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) what might cause this conflict and how can i fix it? Thanks

  Read the article

• Accidentally dd'ed an image to wrong drive / overwrote partition table + NTFS partition start

  - by Kento Locatelli

  I screwed up and set the wrong output for dd when trying to copy a freenas iso, overwriting the wrong external hard drive. Ironically, I was trying to setup a freenas server for data backup... External drive is only used for data storage, system is entirely intact Drive had a single NTFS partition filing the entire device (2TB WD elements) Drive originally had an MBR partition table. Drive now shows as having a GPT, presumably from the freenas image. Drive was mounted at the time, with maybe a couple kB of data written/read after running dd Drive is just a few months old and healthy (regular SMART / fs checks) I have not reboot the OS (crunchbang) /proc/partition still holds the correct information (and has been stored) Have dd's output (records in / out / bytes) testdrive did not find any partitions on quick or deep search running photorec to recover the more important data (a couple recent plaintext files that hadn't been backed up yet). Vast majority of disk content ( 80%) is unnecessary media files. My current plan is to let photorec do it's thing, then recreate the mbr with gparted and use cfdisk to create another NTFS partition using the sector information from /sys/block/.../. Is that a good course of action (that is, a chance of success)? Or anything else I should try first? Possibly relevant information: dd if=FreeNAS-8.0.4-RELEASE-p3-x86.iso of=/dev/sdc: 194568+0 records in 194568+0 records out 99618816 bytes (100 MB) copied grep . /sys/block/sdc/sdc*/{start,size}: /sys/block/sdc/sdc1/start:2048 /sys/block/sdc/sdc1/size:3907022848 cat /proc/partitions: major minor #blocks name ** Snipped ** 8 32 1953512448 sdc 8 33 1953511424 sdc1 current fdisk -l output: WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 2000.4 GB, 2000396746752 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table

  Read the article

• Mailman delivery troubles

  - by stanigator

  I have apparently posted at the wrong place (superuser.com) for this question, so I'll just repost it here. Hope those of you who read both sites are not going to be offended. It's about mailing list management software called Mailman from GNU. Here are the details: Hosting provider: Vlexofree Domain: www.sysil.com with Google Apps Mailing List created from hosting cpanel: [email protected] I have registered a list of subscribers, and tried sending an email to [email protected]. I got the following error message: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550-5.1.1 The email account that you tried to reach does not exist. Please try 550-5.1.1 double-checking the recipient's email address for typos or 550-5.1.1 unnecessary spaces. Learn more at 550 5.1.1 http://mail.google.com/support/bin/answer.py?answer=6596 23si6479194ewy.44 (state 14). ----- Original message ----- MIME-Version: 1.0 Received: by 10.216.90.136 with SMTP id e8mr1469147wef.110.1264220118960; Fri, 22 Jan 2010 20:15:18 -0800 (PST) Date: Fri, 22 Jan 2010 20:15:18 -0800 Message-ID: <[email protected]> Subject: From: Stanley Lee <[email protected]> To: [email protected] Content-Type: multipart/alternative; boundary=0016e6dab0931bccc3047dcd2f1e - Show quoted text - Is there any way of fixing this problem? I would like to be able to have this mailing list to work through my hosting and domain. Thanks in advance.

  Read the article

• ubuntu 10.04 + php + postfix

  - by mononym

  I have a server I am running: Ubuntu 10.04 php 5.3.5 (fpm) Nginx I have installed postfix, and set it to loopback-only (only need to send) The problem is it is not sending. if i issue (at command line): echo "testing local delivery" | mail -s "test email to localhost" [email protected] I get the email no problem, but through PHP it does not arrive. When I send it via PHP, mail.log shows: Mar 28 10:15:04 host postfix/pickup[32102]: 435EF580D7: uid=0 from=<root> Mar 28 10:15:04 host postfix/cleanup[32229]: 435EF580D7: message-id=<20120328091504.435EF580D7@FQDN> Mar 28 10:15:04 host postfix/qmgr[32103]: 435EF580D7: from=<root@FQDN>, size=1127, nrcpt=1 (queue active) Mar 28 10:15:04 host postfix/local[32230]: 435EF580D7: to=<root@FQDN>, orig_to=<root>, relay=local, delay=3.1, delays=3/0.01/0/0.09, dsn=2.0.0, status=sent (delivered to maildir) Mar 28 10:15:04 host postfix/qmgr[32103]: 435EF580D7: removed any help appreciated, my main.cf file: smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = FQDN alias_maps = hash:/etc/aliasesalias_database = hash:/etc/aliases myorigin = /etc/mailname #myorigin = $mydomain mydestination = FQDN, localhost.FQDN, , localhost relayhost = $mydomain mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = loopback-only virtual_alias_maps = hash:/etc/postfix/virtual home_mailbox = mail/

  Read the article

• mkfs Operation Takes Very Long on Linux Software Raid 5

  - by Elmar Weber

  I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

  Read the article

• What are these CPU cache settings? Snoop Filter, ACL prefetch, HW prefetch

  - by eater

  I was in my BIOS setup turning on VT-x support today and saw these other settings. A little googling indicates that they each seem to turn on some sort of optimization to do with the CPU's L2 cache. They were all turned off by default. The processor in question is an Intel Xeon quad-core 3.4GHz (X5492). My OS is Linux 2.6.35.10-74.fc14.x86_64 #1 SMP Thu Dec 23 16:04:50 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux. I have 4GB of RAM if that matters. Here's what the BIOS manufacturer has to say: Snoop Filter Enabling the snoop filter typically improves performance by reducing snoop traffic on the frontside bus in dual processor configurations. Well I like the sound of improved performance. Why would the BIOS have this off by default? Or by dual processor do they not mean multi-core? Regardless, is there a downside if this is on? ACL Prefetch When enabled, the Adjacent Cache Line Prefetcher fetches both cache lines that comprise a cache line pair when it determines required data is not currently in its cache. When disabled, the processor will only fetch the cache line required by the processor. HW Prefetch Fetches an extra line of data into L2 from external memory. Both of these sound like optimizations that have some drawbacks. What are the reasons to turn them on? What are the reasons to leave them off. Why is the default off?

  Read the article

• How to install ia32-libs on Wheezy?

  - by javano

  I have seen a couple of questions on ServerFault relating to installing ia32-libs on a 64bit machine but the solutions aren't working for me (I don't think any of these questions where for Wheezy specifically I'm not sure how to proceed); root@server:/home/# apt-get install -f ia32-libs Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 php5 : Depends: libapache2-mod-php5 (>= 5.4.4-14+deb7u2) but it is not going to be installed or libapache2-mod-php5filter (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-cgi (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-fpm (>= 5.4.4-14+deb7u2) but it is not going to be installed php5-mysql : Depends: phpapi-20100525 E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. root@server:/home/# sudo apt-get install ia32-libs-i386 Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs-i386:i386 : Depends: freeglut3:i386 (>= 2.6.0-1) but it is not going to be installed Depends: lesstif2:i386 (>= 1:0.95.2-1) but it is not going to be installed Depends: libacl1:i386 (>= 2.2.49-4) but it is not going to be installed Depends: libasyncns0:i386 (>= 0.3-1.1) but it is not going to be installed Depends: libattr1:i386 (>= 1:2.4.44-2) but it is not going to be installed Depends: libaudio2:i386 (>= 1.9.2-4) but it is not going to be installed Depends: libaudiofile1:i386 (>= 0.2.6-8) but it is not going to be installed Depends: libavahi-client3:i386 (>= 0.6.27-2+squeeze1) but it is not going to be installed Depends: libavahi-common3:i386 (>= 0.6.27-2+squeeze1) but it is not going to be installed Depends: libbsd0:i386 (>= 0.2.0-1) but it is not going to be installed Depends: libcap2:i386 (>= 1:2.19-3) but it is not going to be installed Depends: libcomerr2:i386 (>= 1.41.12-4stable1) but it is not going to be installed Depends: libcups2:i386 (>= 1.4.4-7+squeeze1) but it is not going to be installed Depends: libcurl3:i386 (>= 7.21.0-2) but it is not going to be installed Depends: libdbus-1-3:i386 (>= 1.2.24-4+squeeze1) but it is not going to be installed Depends: libdirectfb-1.2-9:i386 (>= 1.2.10.0-4) but it is not going to be installed Depends: libdrm-intel1:i386 (>= 2.4.21-1~squeeze3) but it is not going to be installed Depends: libdrm-radeon1:i386 (>= 2.4.21-1~squeeze3) but it is not going to be installed Depends: libdrm2:i386 (>= 2.4.21-1~squeeze3) but it is not going to be installed Depends: libedit2:i386 (>= 2.11-20080614-2) but it is not going to be installed Depends: libesd0:i386 (>= 0.2.41-8) but it is not going to be installed Depends: libexif12:i386 (>= 0.6.19-1) but it is not going to be installed Depends: libexpat1:i386 (>= 2.0.1-7) but it is not going to be installed Depends: libflac8:i386 (>= 1.2.1-2+b1) but it is not going to be installed Depends: libfltk1.1:i386 (>= 1.1.10-2+b1) but it is not going to be installed Depends: libfontconfig1:i386 (>= 2.8.0-2.1) but it is not going to be installed Depends: libfreetype6:i386 (>= 2.4.2-2.1+squeeze3) but it is not going to be installed Depends: libgcrypt11:i386 (>= 1.4.5-2) but it is not going to be installed Depends: libgdbm3:i386 (>= 1.8.3-9) but it is not going to be installed Depends: libgl1-mesa-dri:i386 (>= 7.7.1-5) but it is not going to be installed Depends: libgl1-mesa-glx:i386 (>= 7.7.1-5) but it is not going to be installed Depends: libglu1-mesa:i386 (>= 7.7.1-5) but it is not going to be installed Depends: libgnutls26:i386 (>= 2.8.6-1) but it is not going to be installed Depends: libgpg-error0:i386 (>= 1.6-1) but it is not going to be installed Depends: libgphoto2-2:i386 (>= 2.4.6-3) but it is not going to be installed Depends: libgphoto2-port0:i386 (>= 2.4.6-3) but it is not going to be installed Depends: libgssapi-krb5-2:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: libice6:i386 (>= 2:1.0.6-2) but it is not going to be installed Depends: libidn11:i386 (>= 1.15-2) but it is not going to be installed Depends: libieee1284-3:i386 (>= 0.2.11-6) but it is not going to be installed Depends: libjack-jackd2-0:i386 (>= 1.9.5~dfsg-14) but it is not going to be installed or libjack0:i386 (>= 1:0.118+svn3796-7) but it is not going to be installed Depends: libjpeg62:i386 (>= 6b1-1) but it is not going to be installed Depends: libjpeg8:i386 (>= 8b-1) but it is not going to be installed Depends: libk5crypto3:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: libkeyutils1:i386 (>= 1.4-1) but it is not going to be installed Depends: libkrb5-3:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: libkrb5support0:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: liblcms1:i386 (>= 1.18.dfsg-1.2+b3) but it is not going to be installed Depends: libltdl7:i386 (>= 2.2.6b-2) but it is not going to be installed Depends: liblzo2-2:i386 (>= 2.03-2) but it is not going to be installed Depends: libmpg123-0:i386 (>= 1.12.1-3) but it is not going to be installed Depends: libnspr4-0d:i386 (>= 4.8.6-1) but it is not going to be installed Depends: libnss3-1d:i386 (>= 3.12.8-1+squeeze4) but it is not going to be installed Depends: libogg0:i386 (>= 1.2.0~dfsg-1) but it is not going to be installed Depends: libopenal1:i386 (>= 1:1.12.854-2) but it is not going to be installed Depends: libpam0g:i386 (>= 1.1.1-6.1+squeeze1) but it is not going to be installed Depends: libpng12-0:i386 (>= 1.2.44-1+squeeze1) but it is not going to be installed Depends: libpopt0:i386 (>= 1.16-1) but it is not going to be installed Depends: libpulse0:i386 (>= 0.9.21-3+squeeze1) but it is not going to be installed Depends: libsamplerate0:i386 (>= 0.1.7-3) but it is not going to be installed Depends: libsane:i386 (>= 1.0.21-9) but it is not going to be installed Depends: libsasl2-2:i386 (>= 2.1.23.dfsg1-7) but it is not going to be installed Depends: libsdl1.2debian:i386 (>= 1.2.15) but it is not going to be installed Depends: libselinux1:i386 (>= 2.0.96-1) but it is not going to be installed Depends: libsigc++-2.0-0c2a:i386 (>= 2.2.4.2-1) but it is not going to be installed Depends: libsm6:i386 (>= 2:1.1.1-1) but it is not going to be installed Depends: libsndfile1:i386 (>= 1.0.21-3+squeeze1) but it is not going to be installed Depends: libsqlite3-0:i386 (>= 3.7.3-1) but it is not going to be installed Depends: libssh2-1:i386 (>= 1.2.6-1) but it is not going to be installed Depends: libssl1.0.0:i386 (>= 1) but it is not going to be installed Depends: libstdc++5:i386 (>= 1:3.3.6-20) but it is not going to be installed Depends: libsvga1:i386 (>= 1:1.4.3-29) but it is not going to be installed Depends: libsysfs2:i386 (>= 2.1.0+repack-1) but it is not going to be installed Depends: libtasn1-3:i386 (>= 2.7-1) but it is not going to be installed Depends: libtdb1:i386 (>= 1.2.1-2+b1) but it is not going to be installed Depends: libtiff4:i386 (>= 3.9.4-5+squeeze3) but it is not going to be installed Depends: libts-0.0-0:i386 (>= 1.0-7) but it is not going to be installed Depends: libusb-0.1-4:i386 (>= 2:0.1.12-16) but it is not going to be installed Depends: libuuid1:i386 (>= 2.17.2-9) but it is not going to be installed Depends: libvorbis0a:i386 (>= 1.3.1-1) but it is not going to be installed Depends: libvorbisenc2:i386 (>= 1.3.1-1) but it is not going to be installed Depends: libvorbisfile3:i386 (>= 1.3.1-1) but it is not going to be installed Depends: libwrap0:i386 (>= 7.6.q-19) but it is not going to be installed Depends: libx11-6:i386 (>= 2:1.3.3-4) but it is not going to be installed Depends: libx86-1:i386 (>= 1.1+ds1-6) but it is not going to be installed Depends: libxau6:i386 (>= 1:1.0.6-1) but it is not going to be installed Depends: libxaw7:i386 (>= 2:1.0.7-1) but it is not going to be installed Depends: libxcb-render-util0:i386 (>= 0.3.6-1) but it is not going to be installed Depends: libxcb-render0:i386 (>= 1.6-1) but it is not going to be installed Depends: libxcb1:i386 (>= 1.6-1) but it is not going to be installed Depends: libxcomposite1:i386 (>= 1:0.4.2-1) but it is not going to be installed Depends: libxcursor1:i386 (>= 1:1.1.10-2) but it is not going to be installed Depends: libxdamage1:i386 (>= 1:1.1.3-1) but it is not going to be installed Depends: libxdmcp6:i386 (>= 1:1.0.3-2) but it is not going to be installed Depends: libxext6:i386 (>= 2:1.1.2-1) but it is not going to be installed Depends: libxfixes3:i386 (>= 1:4.0.5-1) but it is not going to be installed Depends: libxft2:i386 (>= 2.1.14-2) but it is not going to be installed Depends: libxi6:i386 (>= 2:1.3-6) but it is not going to be installed Depends: libxinerama1:i386 (>= 2:1.1-3) but it is not going to be installed Depends: libxml2:i386 (>= 2.7.8.dfsg-2+squeeze1) but it is not going to be installed Depends: libxmu6:i386 (>= 2:1.0.5-2) but it is not going to be installed Depends: libxmuu1:i386 (>= 2:1.0.5-2) but it is not going to be installed Depends: libxp6:i386 (>= 1:1.0.0.xsf1-2) but it is not going to be installed Depends: libxpm4:i386 (>= 1:3.5.8-1) but it is not going to be installed Depends: libxrandr2:i386 (>= 2:1.3.0-3) but it is not going to be installed Depends: libxrender1:i386 (>= 1:0.9.6-1) but it is not going to be installed Depends: libxslt1.1:i386 (>= 1.1.26-6) but it is not going to be installed Depends: libxss1:i386 (>= 1:1.2.0-2) but it is not going to be installed Depends: libxt6:i386 (>= 1:1.0.7-1) but it is not going to be installed Depends: libxtst6:i386 (>= 2:1.1.0-3) but it is not going to be installed Depends: libxv1:i386 (>= 2:1.0.5-1) but it is not going to be installed Depends: libxxf86vm1:i386 (>= 1:1.1.0-2) but it is not going to be installed Depends: odbcinst1debian2:i386 (>= 2.2.14p2-1) but it is not going to be installed Depends: libodbc1:i386 but it is not going to be installed Depends: xaw3dg:i386 (>= 1.5+E-18) but it is not going to be installed php5 : Depends: libapache2-mod-php5 (>= 5.4.4-14+deb7u2) but it is not going to be installed or libapache2-mod-php5filter (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-cgi (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-fpm (>= 5.4.4-14+deb7u2) but it is not going to be installed php5-mysql : Depends: phpapi-20100525 E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. root@server:/home/# dpkg --print-architecture amd64 root@server:/home/# dpkg --print-foreign-architectures i386 root@server:/home/# lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 7.1 (wheezy) Release: 7.1 Codename: wheezy root@server:/home/# uname -a Linux servername 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux root@server:/home/# cat /etc/apt/sources.list deb http://ftp.us.debian.org/debian stable main contrib non-free

  Read the article

• Telugu (unicode) font rendering in emacs

  - by Prakash K

  [I asked the following question in stackoverflow, and I have been redirected here. I hope I can get some answers here. My question at stackoverflow had two small images showing the example rendering of text. As a new user at superuser, I am not being allowed to include them here, nor I am allowed to post more than one hyperlink. And, I don't have enough reputation on SO to migrate that question. Please look at the stackoverflow question for the images. Sorry about the inconvenience.] I sometimes edit text in telugu language. However, when I open the file (UTF-8 encoded) in GNU emacs (version 23.1.50.1 on Ubuntu Jaunty) the text rendering is incorrect. The same text file opened in gedit is rendered correctly. Here's a snippet: ????????? ???? ???? ???????? rendred in gedit: Please see the SO question for the image showing telugu text rendering in gedit And, the emacs rendering of the same text: Please see the SO question for the image showing telugu text rendering in emacs Wherever glyphs need to be composited (not sure if it's the right word), emacs (or whatever library it uses) is not doing it right. Is there anyway to fix this? Perhaps tuning some setting in my configuration? Any ideas, please?

  Read the article

• Replace Linux Boot-Drive | ext3 to btrfs

  - by bardiir

  I've got a headless server running Debian Linux currently. Linux vault 3.2.0-3-686-pae #1 SMP Mon Jul 23 03:50:34 UTC 2012 i686 GNU/Linux The root filesystem is located on an ext3 partition on the main harddrive. My data is located on multiple harddrives that are bundled to a storage pool running with btrfs. UUID=072a7fce-bfea-46fa-923f-4fb0827ae428 / ext3 errors=remount-ro 0 1 UUID=b50965f1-a2e1-443f-876f-578b5f93cbf1 none swap sw 0 0 UUID=881e3ad9-31c4-4296-ae60-eae6c98ea45f none swap sw 0 0 UUID=30d8ae34-e2f0-44b4-bbcc-22d761a128f6 /data btrfs defaults,compress,autodefrag 0 0 What I'd like to do is to place / into the btrfs pool too. The ideal solution would provide the flexibility to boot from any disk in the system alike, so if the main drive fails I'd just need to swap another one into the main slot and it would be bootable like the main one. My main problem is, everything I do needs to result in a bootable system that is open to ssh logins via network as this server is 100% headless so there is no possibility to boot it from a live cd or anything like that. So I'd like to be extra sure everything works out fine :) How would I best go about this? Can anybody hint me to guides or whip something up for these tasks? Anything I forgot to think about? Copy root-data into btrfs pool, adjust mountpoints,... Adjust GRUB to boot from btrfs pool UUID or the local device where GRUB is installed Sync GRUB to all harddrives so every drive is equally bootable (is this even possible without destroying the btrfs partitions on the drives or would I need to disconnect the drives, install grub on them and then connect them back with a slightly smaller partition?)

  Read the article

• How to calibrate ASUS k52f battery on Ubuntu?

  - by cutalion

  I'm not sure if the problem is in software or my battery is dying, I'll move my question to another forum if it's not a SO question I have a problem with the battery on my laptop - ASUS K52F. It shows incorrect information about capacity. When I unplug the charger it can work some time, but then it will power off without any warnings. Sometimes it will power off right after I unplug the charger. Here is some info I could get: > uname -a Linux alligator 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux > acpi -i Battery 0: Charging, 99%, 18:25:15 until charged Battery 0: design capacity 5235 mAh, last full capacity 69964 mAh = 100% > cat /sys/class/power_supply/BAT0/uevent POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Charging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=9246000 POWER_SUPPLY_POWER_NOW=176000 POWER_SUPPLY_ENERGY_FULL_DESIGN=**48400000** POWER_SUPPLY_ENERGY_FULL=**646822000** POWER_SUPPLY_ENERGY_NOW=**643588000** POWER_SUPPLY_MODEL_NAME=K52F-44 POWER_SUPPLY_MANUFACTURER=ASUSTek POWER_SUPPLY_SERIAL_NUMBER= I noticed, that POWER_SUPPLY_ENERGY_NOW and POWER_SUPPLY_ENERGY_FULL are greater than POWER_SUPPLY_ENERGY_FULL_DESIGN. I don't think it's ok :) I can run any additional commands.

  Read the article

• lighttpd: why using port >= 9000 does not work properly

  - by yejinxin

  I had a lighttpd server which works normally. I can access this website from outside(non-localhost) via http://vm.aaa.com:8080. Let's just assume that it's a simple static website, without php or mysql. Now I want to copy this website as a test one(using another port) in the same machine. And I do not want to use virtual host. So I just copy the whole files of original server, including lighttpd's bin/ conf/ htdocs/ lib/ and so on folders. And I made some required change, including changing lighttpd.conf. Now what I'm confused is, if change the port to a number that is less than 9000, it works perfectly. But if the port is changed to a number that is equal or greater than 9000, lighttpd can start, but I can not access the new website from outside, while I do can access the new website from INSIDE(I mean in the same LAN or localhost). The access log from INSIDE is like below: vm.aaa.com:9876 10.46.175.117 - - [08/Oct/2012:13:18:47 +0800] "GET / HTTP/1.1" 200 15 "-" " curl/7.12.1 (x86_64-redhat-linux-gnu) libcurl/7.12.1 OpenSSL/0.9.7a zlib/1.2.1.2 libidn/0.5.6" Command I used to start lighttpd is: bin/lighttpd -f conf/lighttpd.conf -m lib/ -D My lighttpd.conf is like: server.modules = ( "mod_access", "mod_accesslog", ) var.rundir = "/home/work/lighttpd_9876" server.port = 9876 server.bind = "0.0.0.0" server.pid-file = var.rundir + "/log/lighttpd.pid" server.document-root = var.rundir + "/htdocs/" var.cronolog_path = "/home/work/lighttpd_9876/cronolog/sbin/cronolog" server.errorlog = ... accesslog.filename = ... ... So why is this happening? I've tried several diffrent ports, still the same. Isn't that ports between 8000 and 65535 are the same?

  Read the article

• Slow manipulation of netfilter rules

  - by Ole Martin Eide

  I have a script maintaining gre tunnels and firewall rules using the "ip" and "iptables" tools. Setting up hundreds of tunnels, and adresses per interface runs just fine. Takes less than 0.1 second per interface, however when I get around to do the firewall rules everything slows down spending 0.5 per insertion. Why is it running so slow? What can I do to improve the speed? It seems like I could try ipset instead, but I really feel there is something wrong with the kernel or something. The interesting thing is that the first 10 rules runs fast, then it slows down.. mybox(root) foo# iptables -V iptables v1.3.5 mybox(root) foo# uname -a Linux foo 2.6.18-164.el5 #1 SMP Tue Aug 18 15:51:48 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux mybox(root) foo# cat test.sh #!/bin/sh for n in {1..100} do /sbin/iptables -A OUTPUT -s ${n} -j ACCEPT /sbin/iptables -D OUTPUT -s ${n} -j ACCEPT done mybox(root) foo# time ./test.sh real 1m38.839s user 0m0.100s sys 1m38.724s Appriciate any help. Cheers!

  Read the article

• OpenVPN-based VPN server on same system it's "protecting": feasible?

  - by Johnny Utahh

  Scenario: hosted machine (typically a VPS) serving wiki, svn, git, forums, email lists (eg: GNU mailman), Bugzilla (etc) privately to < 20 people. People not on team not allowed access. Seeking VPN-restricted access to said server. Have good user experience with OpenVPN-based servers/clients, but have yet to server-admin such systems. Otherwise, experienced Linux sysadmin. Target system: Ubuntu, probably 12.04. Seeking to put an OpenVPN process on above server to "protect" all the above-mentioned services, enabling only OpenVPN-authorized clients/processes to access above services. (Can easily acquire additional IP address(es) as needed for this setup.) Option: if absolutely needed, can employ an additional, dedicated, "VPN server" VPS simply to be my VPN server "front end." But prefer to have all server processes (VPN server plus other server apps) all running on same machine, if possible. Will consider further if dedicated-VPN-machine setup enables 1. easier installation/administration, 2. better/easier end-user experience, and/or 3. makes system significantly more secure. Any of above feasible? The main intention: create a VPN from purely-hosted resources, and not spend all the effort to make a non-VPN, secure site--which typically means "SSL wrapping" + all the continual webserver-application-update management. Let the VPN server deal with access security, and spend list time pushing said security "down" in the other apps/Apache.

  Read the article

• Weird rendering artefact in vim (terminal, not MacVim)

  - by Tobi Lehman

  Running Mac OS X, using either Terminal.app or iTerm2, there is a strange artefact with the character rendering that I have a hard time explaining and an even harder time understanding. I'll start with a video of my screen so that you can see and example of it in action: From the video you can see a few ways it is weird, for example, sometimes when I hit a letter in insert mode, the character is double printed. When I go into normal mode, the artefact remains. When I re-enter insert mode, hitting backspace copies the characters on the left to the position under the cursor. This has happened in OS X Lion, and Mountain Lion, under both Terminal.app and iTerm 2. This never happens under MacVim. Also, I use GNU/Linux on my other machine, and have never had this happen, I am pretty sure it is strictly a Mac OS X issue, but I do not know how to fix it. For a while, I've been working around it by using MacVim most of the time, but I prefer working in a terminal. Does anyone know what is happening here, and if so, how can I fix it? EDIT: I tried using the macvim Vim executable, and I still get strange artefacts, but they are localized to the left side of the screen, here is an example:

  Read the article

• Slow connection to Linux MySQL from Windows only (XAMPP)

  - by Josh

  I'm having a problem with a PHP project (using Kohana 3.2 framework) on my Windows 7 64-bit machine connecting to the database. The development database is stored on a Ubuntu Linux server on the local network. Other development machines running OSX and Linux are connecting fine. There are no other Windows development machines to test with. I can access MySQL fine using MySQL Workbench, and other projects (which I believe to be less database heavy) run mostly ok, only occasionally getting timeout messages. I'm constantly getting Maximum execution time of 30 seconds exceeded when functions such as mysql_query() are run in this particular project. Specifically, the Kohana file where the timeout occurs is MODPATH\database\classes\kohana\database\mysql.php [ 186 ]. My local set-up is: Windows 7 Professional 64bit XAMPP 1.7.7 (PHP 5.3.8) The output of uname -a of the Linux server is: Linux peach 2.6.38-11-server #50-Ubuntu SMP Mon Sep 12 21:34:27 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux I've tried the following, with no success: Disabling Windows firewall Switching between using a persistant and normal connection In my.cnf, adding skip-name-resolve Increasing wait_timeout Enabling bind-address I've run out of ideas now, and have no idea how to debug an odd issue like this. Has anyone come across this before, or have any idea how I could find the root of the issue, or what might be the problem?

  Read the article

• Centos 6.2 postfix install dependency issues

  - by Mishari

  I am administrating a VPS running cPanel and I'm trying to install postfix. Redhat-release says the version is CentOS release 6.2 (Final) and uname -a says: Linux server.mydomain.com 2.6.32-220.el6.i686 #1 SMP Tue Dec 6 16:15:40 GMT 2011 i686 i686 i386 GNU/Linux This is how I'm installing postfix (I had tried to solve the problem earlier by installing epel). # yum install postfix Loaded plugins: fastestmirror, security Loading mirror speeds from cached hostfile * epel: mirror.cogentco.com Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package postfix.i686 2:2.6.6-2.2.el6_1 will be installed --> Processing Dependency: mysql-libs for package: 2:postfix-2.6.6-2.2.el6_1.i686 --> Finished Dependency Resolution Error: Package: 2:postfix-2.6.6-2.2.el6_1.i686 (centos-burstnet) Requires: mysql-libs You could try using --skip-broken to work around the problem Attempts to install mysql-libs tells me several files conflict with "MySQL-server-5.1.61-0.glibc23.i386" I'm not sure why or how this is happening, does anyone know how to resolve this? Surely Centos 6.2 could not have shipped with a broken postfix.

  Read the article

• Macports install of ack doesn't create correct executable

  - by user1664196

  I am trying to install p5-app-ack port from Mac Ports, but it seems it doesn't create a /opt/local/bin/ack binary at the end: $ sudo port search *app-ack Password: p5-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.8-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.10-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.12-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.14-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.16-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories Found 6 ports. $ perl --version This is perl 5, version 12, subversion 4 (v5.12.4) built for darwin-thread-multi-2level Copyright 1987-2010, Larry Wall Perl may be copied only under the terms of either the Artistic License or the GNU General Public License, which may be found in the Perl 5 source kit. Complete documentation for Perl, including FAQ lists, should be found on this system using "man perl" or "perldoc perl". If you have access to the Internet, point your browser at http://www.perl.org/, the Perl Home Page. $ sudo port install p5-app-ack ---> Computing dependencies for p5-app-ack ---> Cleaning p5-app-ack ---> Updating database of binaries: 100.0% ---> Scanning binaries for linking errors: 35.0% ---> No broken files found. $ $ ls /opt/local/bin/ac* /opt/local/bin/ack-5.12 /opt/local/bin/aclocal /opt/local/bin/aclocal-1.12 /opt/local/bin/activation-client /opt/local/bin/acyclic $ which ack $ ack -bash: ack: command not found Update If I then try to install p5.12-app-ack afterwards, I get $ sudo port install p5.12-app-ack Password: ---> Computing dependencies for p5.12-app-ack ---> Cleaning p5.12-app-ack ---> Scanning binaries for linking errors: 100.0% ---> No broken files found. $

  Read the article

• grub refuses to install to raid array

  - by ronno

  I have a software raid 0 setup with dual booting Windows 7 and Ubuntu 12.04. The GRUB bootloader that is already on the hard drive seems to work fine. However, since the latest package update for grub, it refuses to install the new version to the hard disk. grub-install throws the following error: /usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map. Auto-detection of a filesystem of /dev/mapper/< raid name_RAID0p9 failed. Try with --recheck. If the problem persists please report this together with the output of "/usr/sbin/grub-probe --device-map="/boot/grub/device.map" --target=fs -v /boot/grub" to < [email protected] update-grub pops the same "/usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map." every alternate line. I don't understand what exactly is going on. I'm afraid to reinstall the grub package because it might mess up the boot, which currently works fine. Is it safe to just ignore this?

  Read the article

• High disk I/O activity in CentOS server

  - by triiim

  I have about 16 websites in a CentOS dedicated, and I am having some problems on high traffic hours, it seems to be a high disk I/O activity causing a general slowdown. I've installed atop and this is what I see on the bottom (the server has been restarted thats why the values are so low): *** system and process activity since boot *** PID RDDSK WRDSK WCANCL DSK CMD 1/18 2176 1.7G 7.3G 854.4M 39 mysqld 671 1248K 3.0G 0K 13 flush-8:0 566 0K 1.1G 0K 5 jbd2/sda2-8 2401 124.2M 529.1M 22408K 3 crond 2032 2.2G 502.0M 0K 12 nginx 2360 425.8M 115.3M 4188K 2 httpd flush-8:0 and jbd2/sda2-8 are the processes I see with iotop using 99% on the IO column, and they are the processes that write the most on the hdd (after mysql). From what I saw in google this could be caused by some ext4 related bug, the current kernel is: Linux srvr.com 2.6.32-71.29.1.el6.x86_64 #1 SMP Mon Jun 27 19:49:27 BST 2011 x86_64 x86_64 x86_64 GNU/Linux I asked the hosting support to update the kernel and they tried but they now say that the server wont boot with the new installed kernel and they had to go back to the previous, they are not helping very much. Does someone has any idea how could I solve the high disk usage caused by flush-8:0 and jbd2/sda2-8 processes?

  Read the article

• Nginx server 301 Moved permanently

  - by user145714

  When I did a curl -v http://site-wordpress.com:81 I received this result: About to connect() to site-wordpress.com port 81 (#0) Trying ip... connected Connected to site-wordpress.com (ip) port 81 (#0) GET / HTTP/1.1 User-Agent: curl/7.19.7 (x86_64-unknown-linux-gnu) libcurl/7.19.7 NSS/3.12.6.2 zlib/1.2.3 libidn/1.18 libssh2/1.2.2 Host: site-wordpress.com:81 Accept: / < HTTP/1.1 301 Moved Permanently < Server: nginx/1.2.4 < Date: Fri, 16 Nov 2012 16:28:19 GMT < Content-Type: text/html; charset=UTF-8 < Transfer-Encoding: chunked < Connection: keep-alive < X-Pingback: The URL above/xmlrpc.php < Location: The URL above Seems like this line in my fastcgi_params is causing grief. fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; If I remove this line , I get HTTP/1.1 200 OK but I get a blank page. This is my config: server { listen 81; server_name site-wordpress.com; root /var/www/html/site; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; index index.php; if (!-e $request_filename){ rewrite ^(.*)$ /index.php break; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; # port where FastCGI processes were spawned fastcgi_index index.php; include /etc/nginx/fastcgi_params; include /etc/nginx/mime.types; } location ~ \.css { add_header Content-Type text/css; } location ~ \.js { add_header Content-Type application/x-javascript; } } This config works with ip and port 80. But now I need to use a domain name and port 81, which doesn't work. Could someone please help. Thanks.

  Read the article

• TCP dies on a Linux laptop

  - by Roman Cheplyaka

  Once in several days I have the following problem. My laptop (Debian GNU/Linux testing) suddenly becomes unable to work with TCP connections to the internet. The following things continue to work fine: UDP (DNS), ICMP (ping) — I get instant response TCP connections to other machines in the local network (e.g. I can ssh to a neighbour laptop) everything is ok for other machines in my LAN But when I try TCP connections from my laptop, they time out (no response to SYN packets). Here's a typical curl output: % curl -v google.com * About to connect() to google.com port 80 (#0) * Trying 173.194.39.105... * Connection timed out * Trying 173.194.39.110... * Connection timed out * Trying 173.194.39.97... * Connection timed out * Trying 173.194.39.102... * Timeout * Trying 173.194.39.98... * Timeout * Trying 173.194.39.96... * Timeout * Trying 173.194.39.103... * Timeout * Trying 173.194.39.99... * Timeout * Trying 173.194.39.101... * Timeout * Trying 173.194.39.104... * Timeout * Trying 173.194.39.100... * Timeout * Trying 2a00:1450:400d:803::1009... * Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable * Success * couldn't connect to host * Closing connection #0 curl: (7) Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable Restarting the connection and/or reloading the network card kernel module doesn't help. The only thing that helps is reboot. Clearly something is wrong with my system (everything else works fine), but I have no idea what exactly. I don't know how to reproduce this, but as I said, it happens every several days. My setup is a wireless router that is connected to the ISP via PPPoE. Any advice?

  Read the article

• apache segmentation error

  - by lush

  I can't start Apache with the following errors: [root@web]# /etc/init.d/httpd start Starting httpd: /bin/bash: line 1: 19232 Segmentation fault /usr/sbin/httpd [root@web]# /usr/sbin/apachectl -k start /usr/sbin/apachectl: line 102: 19919 Segmentation fault $HTTPD $OPTIONS $ARGV I use webmin control panel and I've already tried re-installing Apache from scratch. Can someone advise what else I should try to do? Many thanks. UPDATE: The only line is always written in the error logs which seems not to be very important: [Mon Nov 14 19:00:09 2011] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) UPDATE 2: I've recently had the error below in the logs. Looks like some modules are incompatible, so I've just disabled these extensions: fileinfo and mcrypt in my php.ini. I should be able to start the web server without them. PHP Warning: PHP Startup: fileinfo: Unable to initialize module\nModule compiled with module API=20050922, debug=0, thread-safety=0\nPHP compiled with module API=20060613, debug=0, thread-safety=0\nThese options need to match\n in Unknown on line 0 PHP Warning: Module 'mcrypt' already loaded in Unknown on line 0 UPDATE 3: [root@web]# file /usr/sbin/httpd /usr/sbin/httpd: ELF 64-bit LSB shared object, AMD x86-64, version 1 (SYSV), for GNU/Linux 2.6.9, stripped [root@web]# uname -m x86_64

  Read the article

• Dovecot starting and running, but not listening on any port

  - by Dženis Macanovic

  Among others things I'm in charge of a Debian GNU/Linux (Wheezy) DomU for the mail services of the company i work for. Yesterday one HDD that was used for this particular server has died. After installing Debian again, Dovecot decided to no longer listen on any ports (checked with netstat -l). Other services (like Postfix and MySQL) work without problems. dovecot -n: # 2.1.7: /etc/dovecot/dovecot.conf # OS: Linux 3.2.0-3-amd64 x86_64 Debian wheezy/sid ext3 auth_mechanisms = plain login disable_plaintext_auth = no first_valid_uid = 150 last_valid_uid = 150 mail_gid = mail mail_location = maildir:/var/vmail/%d/%n mail_uid = vmail namespace inbox { inbox = yes location = prefix = } pass db { args = /etc/dovecot/dovecot-sql.conf.ext driver = sql } plugin { sieve = ~/.dovecot.sieve sieve_dir = ~/sieve } service auth { unix_listener /var/spool/postfix/private/auth { group = postfix mode = 0660 user = postfix } unix_listener auth-userdb { group = mail mode = 0666 user = vmail } } service imap-login { inet_listener imaps { port = 993 ssl = yes } } service pop3-login { inet_listener pop3s { port = 995 ssl = yes } } ssl_cert = </etc/ssl/private/mail.crt ssl_key = </etc/ssl/private/mail.key userdb { args = /etc/dovecot/dovecot-sql.conf.ext driver = sql } protocol imap { mail_max_userip_connections = 25 } UID 150 is vmail (I double checked file permissions). I didn't install Dovecot from source, but via apt from the official Debian US mirror. There are no messages concerning Dovecot in /var/log/syslog except for: Oct 21 06:36:29 server dovecot: master: Dovecot v2.1.7 starting up (core dumps disabled) Any ideas?

  Read the article

• HPET missing from available clocksources on CentOS

  - by squareone

  I am having trouble using HPET on my physical machine. It is not available, even though I have enabled it in my bios, forced it in grub, and triple checked my kernel to include HPET in its compilation. Motherboard: Supermicro X9DRW Processor: 2x Intel(R) Xeon(R) CPU E5-2640 SAS Controller: LSI Logic / Symbios Logic SAS2004 PCI-Express Fusion-MPT SAS-2 [Spitfire] (rev 03) Distro: CentOS 6.3 Kernel: 3.4.21-rt32 #2 SMP PREEMPT RT x86_64 GNU/Linux Grub: hpet=force clocksource=hpet .config file: CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_HPET=y dmesg | grep hpet: Command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet Kernel command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet cat /sys/devices/system/clocksource/clocksource0/current_clocksource: tsc cat /sys/devices/system/clocksource/clocksource0/available_clocksource: tsc jiffies What is even more confusing, is that I have about a dozen other machines that utilize the same kernel .config, and can use HPET fine. I fear it is a hardware issue, but would appreciate any advice or help with getting HPET available. Thanks in advance!

  Read the article

• RTL8188CE doesn't connect to any wifi access points

  - by Drakmail

  I'm using network manager to connect. Also, tryed iwconfig. Results are same. I even try to connect to open access point — results are same. More information: Drakmail@thinkpad-x220:~$ lspci | grep Network | grep -v Ethernet 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) Drakmail@thinkpad-x220:~$ uname -a Linux thinkpad-x220 3.1.0 #1 SMP PREEMPT Wed Oct 26 02:19:49 UTC 2011 x86_64 Intel(R) Core(TM) i5-2410M CPU @ 2.30GHz GenuineIntel GNU/Linux Drakmail@thinkpad-x220:~$ dmesg | tail -n 10 [ 846.901574] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 906.812461] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 966.728810] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 1026.639676] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 1030.925574] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin At this moment I try to connect to open wifi ap: [ 1031.252403] wlan0: direct probe to 00:24:8c:55:fa:ed (try 1/3) [ 1031.451943] wlan0: direct probe to 00:24:8c:55:fa:ed (try 2/3) [ 1031.651658] wlan0: direct probe to 00:24:8c:55:fa:ed (try 3/3) [ 1031.851354] wlan0: direct probe to 00:24:8c:55:fa:ed timed out [ 1086.544960] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin My distribution: Drakmail@thinkpad-x220:~$ cat /etc/*version AgiliaLinux release 8.0.0 (Sammy) (Something between Slackware and Archlinux). Also, I saw that wifi module to often trying to load a firmware file. Any ideas what it would be?

  Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >