Search Results

Search found 1543 results on 62 pages for 'motherboard'.

Page 62/62 | < Previous Page | 58 59 60 61 62 

  • How do I reset/update my BIOS for Optiplex GX280?

    - by Sam Langlhey
    So far this has been a nightmare for me, which has been frustrating me constantly. I am using Dell Optiplex GX280 with Windows XP home edition, which is running a BIOS version A04. Recently, i've rebooted the pc to find out that its not booting. It will get to the Windows boot up screen with the progress bar but only to restart to the same process again, over and over. Frustrated that I am, i've inserted the Windows recovery CD to at least either repair of reinstall the operating system to find out that was not possible. I hit F8 to have the boot options, each of the boot option that I've selected gave me an error saying: "Selected boot device is not available." Right after that, I went to the BIOS setting and did a diagnostic test, which recognized all the Boot devices onboard. Now, I cannot even repair of reinstall Windows XP, because the system is not booting from none of the boot devices. The surprise is when I removed the hard-drive from the computer and loaded it on into another computer successfully; that's right, there is nothing wrong with the hard drive. After that I was totally puzzled. I found a few pointers online saying that the BIOS start-up block might be corrupted itself and I might need to flash/update the BIOS. I found the detailed instruction on how to create a Boot up disk by downloading the BIOS firmware from the manufacture's website. I did exactly as instructed below: Download the latest version or your choose version of BIOS file for your computer or motherboard from the manufacturer’s support site. Rename the downloaded file to AMIBOOT.ROM. Copy the file to a floppy disk. Insert the floppy disk to the floppy drive. Turn on the system. After I did that and powered on the PC to boot from the floppy drive, it gave me this error message: "Non-System Disk or Disk Error. Replace and Strike any key when ready." I did all that, and I kept on pressing [Ctrl]+[Home] to force it, but it did not did any satisfying result. Desperate as I am, my next attempt is to try the instruction below. Since I want to be ready, in the event it does not work, do you have any solution that you can provide? Please keep in mind that I cannot boot from any of the devices at this moment. My only hope now is to come on with a solution that will work through the Floppy drive, since that's the only drive that affected. Thank you very much for your advice and support in advance. To create a Windows startup disk, insert a floppy disk into the drive of a similarly configured, working Windows XP system, launch My Computer, right-click the floppy disk icon, and select the Format command from the context menu. When you see the Format dialog box, leave all the default settings as they are and click the Start button. Once the format operation is complete, close the Format dialog box to return to My Computer, double-click the drive C icon to access the root directory, and copy the following three files to the floppy disk: Boot.ini NTLDR Ntdetect.com

    Read the article

  • Rosewill RSV-S5 and it's transferespeeds

    - by DoomStone
    I have just bought a Rosewill RSV-S5, I have installed 5x1,5Tb Western Digital Green disks in it. After that have I created a Raid5 on them all with the software that followed with the hardware. Not the raid it self works fine, but it is SLOW, I can only obtain a maximum of 25 MB/s, and if SABnzbd+ is downloading with 5 MB/s is it having a hard time streaming a normal DIVX (700 mb) movie. Is this normal or is there something wrong? Edit: should be able to handle 3 Gbps = 384 megabytes / second Edit 2: As you can see am I only downloading with 3,76 MB/s and I'm trying to watch V s02e08 (720p), but it is completely unwatchable, as I can see 30 sec, and the it buffers for 20 sec. Edit: Other information there might be required I'm running Windows Server 2008 R2, optimized for program performance. Windows is installed on a 60GB SSD. I have a 50 Mb/s internet connection and a 1 Gb/s LAN, all connected with Cat6 Ethernet cables. The MCE is using a Gigabyte EP35C-DS3R motherboard with 2 GB DDR2 ram. Edit 3: I have used chunk sizes for 128 KB Edit 4: I found this on newegg Pros: Enclosure for 5x2TB hard drive is fine. This is basically a rebranded San Digital TR5M-B product. For support Rosewill tells you to contact San Digital. No direct support from Silicon Image for the computer raid card. Cons: Includes computer Silicon Image 3132 raid card, extremely slow raid 5 write (our tests ~10MB/s). Compare to regular internal local drive write 30-60MB/s. We basically dumped the Sil3132 card and replaced with High Point RocketRaid 622 card for extra $69.99. Note for RR622, turn off ECRC (end to end CRC check) for card to work on IBM xserver. What took 12hrs to copy now took 2-3hrs. San Digital realized the problem and has the newer model TR5M-BP TowerRaid Plus that comes with High Point RocketRaid 622 card. Rosewill should discontinue this product and go with TR5M-BP. Could not get Silicon Image raid management software to work with complicated 2008R2 server with 10 NICs, application doesn't know how to talk to localhost port with all those NICs. No updates from Silicon Image and support from San Digital ignored. Gave up on Sil3132 card. Save yourself from a lot of headaches, get the RR622 card too if you are going to buy this product. Other Thoughts: The newer model is TR5M-BP TowerRaid Plus, comes with High Point RocketRaid 622 raid card for the PC instead of Silicon Image Sil3132. According to San Digital, raid 5 performance for Sil3132 read 80MB/s write 19MB/s, and RR622 read 154MB/s write 149MB/s. Our RR622 tests gave (8TB raid 5) write ~80-110MB/s copying 40GB file took 8mins. So I have now ordered a HighPoint RocketRAID 622 2P ext SATA III and hopes that it will solve my problems.

    Read the article

  • BSOD Code 16, artifacts all over the place (gtx 260)

    - by belinea
    I have a following, quite dated rig E8400 Core 2 Duo cpu Intel Dragontail Peak DP35DP motherboard on Intel Bearlake P35 chipset 4GB ram Geforce 260gtx Corsair 650W PSU Windows 7 64 bit The following things has happened in the last few days. I first decided to update my Nvidia drivers to the latest version. That was 4 days ago. PC worked fine for 2 days and I was able to play few games as well without any problems. Then 2 days ago a first crash happened while playing the new XCOM game. BSOD code 16. Just the blue screen, no artifacts. PC rebooted and worked well again, I continued playing this game for another 2 hours and went to sleep. Next evening I tried to play some BF3 multiplayer (use to play on LOW settings). Approx. 10 minutes into the game red/pink-ish artifacts appeared on the screen and game quit to desktop. Restarted the game and another 3-4 minutes afterwards another crash to desktop but this time followed shortly by BSOD Code 16. From that moment I started to seeing artifacts on random startups, including Windows loading screen and the BIOS itself. Windows would still load but soon enough it would BSOD on a simple task like opening a Internet browser. Today I get tons of artifacts (little small red dashes all over the screen) on BIOS, loading screen, normal Windows mode as well as safe mode. I suspect it wouldn't be drivers but I tried removing and sweeping them entirely in the safe mode. PC would still start with artifacts all over the place but would load the normal mode, just without the driver, in the default lowest resolution. As soon as proper Nvidia drivers are installed though and PC rebooted, Windows doesn't load at all as BSOD now appears on loading screen. However, again, if I go to safe mode and remove drivers, normal mode launches fine. So obviously crash happens only on high resolution. I opened my machine this morning and gave it a proper cleaning even though it wasn't heavily dusted. It didn't help and number of artifacts seems to increase with every PC restart. I write these words in safe mode, which works, but I have to look through all the red dots and dashes. I don't have built in GPU chipset so I can't try removing my Geforce card nor can I borrow A GPU from anyone else. What are my options? I was looking into getting a completely new rig around Christmas so I'm not freaking out about this. If everything points to hardware issue I may simply decide to get the new machine earlier and don't bother with fixing this one. However it would be great to learn more if this is indeed situation that has slim chances of getting sorted. I realize BSOD Code 16 is rather popular topic online but every story seems a bit different and there can be number of issues with it. Hence a new thread.

    Read the article

  • Choice of an OS for a home ZFS NAS

    - by OlafM
    I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post. UPDATES Given the first answers, I will strongly suggest the person paying the hardware to insert a second HD. Better 2x2TB than 1x3TB (3 TB is oversized anyway). I was trying to keep the initial costs down to spread them over a longer period, but better having something good from the beginning.

    Read the article

  • My 3D Games crashing in these scenarios

    - by desaivv
    I have a situation here which I am unable to solve. I bought a PC last year March, here are my specs: Intel Core i3 550 @ 3GHz 4 GB RAM @400 MHz XFX GeForce 9500 GT graphics card 1GB @550MHz 500 GB HDD Lately as soon as I load my save game of Skyrim, it crashes. I have been playing Skyrim since I joined Gaming.SE site. Crashes as in the entire scene gets red lines. I can not ALT + TAB back or even CTRL + ALT + DEL either. My only recourse is a hard reset via the power button. Can not take a screen shot either. I have the latest Forceware 296.10 drivers also. This has been happening since the last 2 weeks. I always use Driver Sweeper to clean my old drivers, since that is what XFXForce recommends before installing new drivers. I installed MSI Afterburner lately to see my GPU temperature. My GPU is default, never over-clocked it. In MSI's Afterburner, I can not adjust fan speed. It is greyed out. Also in settings there is no fan tab. With normal Internet browsing it stays at 51 C. Ran Memtest86 over night with level 11. Took about 13 hours, but no errors in my RAM. I even re-installed my OS, with just the 296 drivers. The fan for the GPU does come on. I can play Diablo 2. I can not get past Warcraft 3's menu selection. There WAS some dust in my machine, but I always try and keep everything clean, since in my home town dust is an issue. Always keep cool my entire PC cabinet. My friend came with his functioning graphics card, we bought our PCs at the same time with exact same specifications. His card did not work either. Same problem with the scene freezing with red lines. I did do my research before posting here. That is how I was able to learn about MSI Afterburner, Driver Sweeper, SpeedFan etc. I followed posts on Tom's Hardware too regarding people that had similar problems. One person suggested and was followed by worked as well the suggestion to "Bake the card in an oven". Since I bought it, played Diablo 2 for months, Starcraft 2 campaign for months and Skyrim recently for months. Bought ME3 also. I am at my wits end. I do not know what else to do. I can go out and buy a card, but my friend's card did not work either. I can use the machine for Eclipse or VS2010 development just fine. Just not with 3D gaming. I originally posted this question on Gaming.SE But I was directed here. I have browsed the SU database for my problem and found this, this, and this. But none of these cover my question. My machine is only one year old. Can some experienced superuser(s) shed some light on this scenario? Is it a 3D graphics card problem? Will a brand new card work? What else can I try to pin point the problem? Can it be the Motherboard? Thanks.

    Read the article

  • Cannot install .NET Framework 4.0 on Windows XP SP3

    - by Bob
    I'm using Windows XP SP3 logged in as the administrator. I had RAID Mirroring running. The motherboard broke earlier in the year. When I got a new battery I did not resync. I just use the disks as two separate disks. I searched Google for the errors but I didn't find anything detailed enough. The following Microsoft components are in Add/Remove programs: .NET Framework 1.1 .NET Framework 2.0 Service Pack 2 .NET Framework 3.0 Service Pack 2 .NET Framework 3.5 SP1 Microsoft Compression Client Pack 1.0 for Windows XP Microsoft Office Enterprise 2007 Microsoft Silverlight Microsoft USB Flash Driver Manager Micrsoft User-mode Driver Framework Feature Pack 1.0 Microsoft Visual C++ 2005 ATL Update KB 973923 x86 8.050727.4053 Microsoft Visual C++ 2005 Redistributable This is the installation log: Exists: evaluating... [10/21/2011, 22:17:14]MsiGetProductInfo with product code {3C3901C5-3455-3E0A-A214-0B093A5070A6} found no matches [10/21/2011, 22:17:14] Exists evaluated to false [10/21/2011, 22:15:50]calling PerformAction on an installing performer [10/21/2011, 22:15:50] Action: Performing actions on all Items... [10/21/2011, 22:15:50]Wait for Item (clr_optimization_v2.0.50727_32) to be available [10/21/2011, 22:15:50]clr_optimization_v2.0.50727_32 is now available to install [10/21/2011, 22:15:50]Creating new Performer for ServiceControl item [10/21/2011, 22:15:50] Action: ServiceControl - Stop clr_optimization_v2.0.50727_32... [10/21/2011, 22:15:50]ServiceControl operation succeeded! [10/21/2011, 22:15:50] Action complete [10/21/2011, 22:15:50]Error 0 is mapped to Custom Error: [10/21/2011, 22:15:50]Wait for Item (Windows6.0-KB956250-v6001-x86.msu) to be available [10/21/2011, 22:15:51]Windows6.0-KB956250-v6001-x86.msu is now available to install [10/21/2011, 22:15:51]Created new DoNothingPerformer for File item [10/21/2011, 22:15:51]No CustomError defined for this item. [10/21/2011, 22:15:51]Wait for Item (Windows6.1-KB958488-v6001-x86.msu) to be available [10/21/2011, 22:15:51]Windows6.1-KB958488-v6001-x86.msu is now available to install [10/21/2011, 22:15:51]Created new DoNothingPerformer for File item [10/21/2011, 22:15:51]No CustomError defined for this item. [10/21/2011, 22:15:51]Wait for Item (netfx_Core.mzz) to be available [10/21/2011, 22:15:52]netfx_Core.mzz is now available to install [10/21/2011, 22:15:52]Created new DoNothingPerformer for File item [10/21/2011, 22:15:52]No CustomError defined for this item. [10/21/2011, 22:15:52]Wait for Item (netfx_Core_x86.msi) to be available [10/21/2011, 22:15:52]netfx_Core_x86.msi is now available to install [10/21/2011, 22:15:52]Creating new Performer for MSI item [10/21/2011, 22:15:52] Action: Performing Action on MSI at F:\DOCUME~1\Owner\LOCALS~1\Temp\Microsoft .NET Framework 4 Client Profile Setup_4.0.30319\netfx_Core_x86.msi... [10/21/2011, 22:15:52]Log File F:\DOCUME~1\Owner\LOCALS~1\Temp\Microsoft .NET Framework 4 Client Profile Setup_20111021_221545515-MSI_netfx_Core_x86.msi.txt does not yet exist but may do at Watson upload time [10/21/2011, 22:15:52]Calling MsiInstallProduct(F:\DOCUME~1\Owner\LOCALS~1\Temp\Microsoft .NET Framework 4 Client Profile Setup_4.0.30319\netfx_Core_x86.msi, EXTUI=1 [10/21/2011, 22:17:14]MSI (F:\DOCUME~1\Owner\LOCALS~1\Temp\Microsoft .NET Framework 4 Client Profile Setup_4.0.30319\netfx_Core_x86.msi) Installation failed. Msi Log: Microsoft .NET Framework 4 Client Profile Setup_20111021_221545515-MSI_netfx_Core_x86.msi.txt [10/21/2011, 22:17:14]PerformOperation returned 1603 (translates to HRESULT = 0x80070643) [10/21/2011, 22:17:14] Action complete [10/21/2011, 22:17:14]OnFailureBehavior for this item is to Rollback. [10/21/2011, 22:17:14] Action: Performing actions on all Items... [10/21/2011, 22:17:14] Action complete [10/21/2011, 22:17:14] Action complete [10/21/2011, 22:17:14]Final Result: Installation failed with error code: (0x80070643), "Fatal error during installation. " (Elapsed time: 0 00:01:29). [10/21/2011, 22:17:41]WM_ACTIVATEAPP: Focus stealer's windows WAS visible, NOT taking back focus SECOND LOG REQUESTED BELOW: MSI (s) (6C:EC) [22:17:13:828]: Invoking remote custom action. DLL: F:\WINDOWS\Installer\MSIBB4.tmp, Entrypoint: NgenUpdateHighestVersionRollback MSI (s) (6C:64) [22:17:13:984]: Executing op: ActionStart(Name=CA_NgenRemoveNicPFROs_I_DEF_x86.3643236F_FC70_11D3_A536_0090278A1BB8,,) MSI (s) (6C:64) [22:17:13:984]: Executing op: ActionStart(Name=CA_NgenRemoveNicPFROs_I_RB_x86.3643236F_FC70_11D3_A536_0090278A1BB8,,) MSI (s) (6C:64) [22:17:13:984]: Executing op: CustomActionRollback(Action=CA_NgenRemoveNicPFROs_I_RB_x86.3643236F_FC70_11D3_A536_0090278A1BB8,ActionType=17729,Source=BinaryData,Target=NgenRemoveNicPFROs,) MSI (s) (6C:AC) [22:17:13:984]: Invoking remote custom action. DLL: F:\WINDOWS\Installer\MSIBB5.tmp, Entrypoint: NgenRemoveNicPFROs MSI (s) (6C:64) [22:17:14:000]: Executing op: End(Checksum=0,ProgressTotalHDWord=0,ProgressTotalLDWord=0) MSI (s) (6C:64) [22:17:14:000]: Error in rollback skipped. Return: 5 MSI (s) (6C:64) [22:17:14:015]: No System Restore sequence number for this installation. MSI (s) (6C:64) [22:17:14:015]: Unlocking Server MSI (s) (6C:64) [22:17:14:015]: PROPERTY CHANGE: Deleting UpdateStarted property. Its current value is '1'. MSI (s) (6C:64) [22:17:14:031]: Note: 1: 1708 MSI (s) (6C:64) [22:17:14:031]: Product: Microsoft .NET Framework 4 Client Profile -- Installation failed. MSI (s) (6C:64) [22:17:14:078]: Cleaning up uninstalled install packages, if any exist MSI (s) (6C:64) [22:17:14:078]: MainEngineThread is returning 1603 MSI (s) (6C:EC) [22:17:14:171]: Destroying RemoteAPI object. MSI (s) (6C:9C) [22:17:14:171]: Custom Action Manager thread ending. MSI (c) (F4:C4) [22:17:14:203]: Decrementing counter to disable shutdown. If counter >= 0, shutdown will be denied. Counter after decrement: -1 MSI (c) (F4:C4) [22:17:14:203]: MainEngineThread is returning 1603 === Verbose logging stopped: 10/21/2011 22:17:14 ===

    Read the article

  • Mysql performance problem & Failed DIMM

    - by murdoch
    Hi I have a dedicated mysql database server which has been having some performance problems recently, under normal load the server will be running fine, then suddenly out of the blue the performance will fall off a cliff. The server isn't using the swap file and there is 12GB of RAM in the server, more than enough for its needs. After contacting my hosting comapnies support they have discovered that there is a failed 2GB DIMM in the server and have scheduled to replace it tomorow morning. My question is could a failed DIMM result in the performance problems I am seeing or is this just coincidence? My worry is that they will replace the ram tomorrow but the problems will persist and I will still be lost of explanations so I am just trying to think ahead. The reason I ask is that there is plenty of RAM in the server, more than required and simply missing 2GB should be a problem, so if this failed DIMM is causing these performance problems then the OS must be trying to access the failed DIMM and slowing down as a result. Does that sound like a credible explanation? This is what DELLs omreport program says about the RAM, notice one dimm is "Critical" Memory Information Health : Critical Memory Operating Mode Fail Over State : Inactive Memory Operating Mode Configuration : Optimizer Attributes of Memory Array(s) Attributes : Location Memory Array 1 : System Board or Motherboard Attributes : Use Memory Array 1 : System Memory Attributes : Installed Capacity Memory Array 1 : 12288 MB Attributes : Maximum Capacity Memory Array 1 : 196608 MB Attributes : Slots Available Memory Array 1 : 18 Attributes : Slots Used Memory Array 1 : 6 Attributes : ECC Type Memory Array 1 : Multibit ECC Total of Memory Array(s) Attributes : Total Installed Capacity Value : 12288 MB Attributes : Total Installed Capacity Available to the OS Value : 12004 MB Attributes : Total Maximum Capacity Value : 196608 MB Details of Memory Array 1 Index : 0 Status : Ok Connector Name : DIMM_A1 Type : DDR3-Registered Size : 2048 MB Index : 1 Status : Ok Connector Name : DIMM_A2 Type : DDR3-Registered Size : 2048 MB Index : 2 Status : Ok Connector Name : DIMM_A3 Type : DDR3-Registered Size : 2048 MB Index : 3 Status : Critical Connector Name : DIMM_B1 Type : DDR3-Registered Size : 2048 MB Index : 4 Status : Ok Connector Name : DIMM_B2 Type : DDR3-Registered Size : 2048 MB Index : 5 Status : Ok Connector Name : DIMM_B3 Type : DDR3-Registered Size : 2048 MB the command free -m shows this, the server seems to be using more than 10GB of ram which would suggest it is trying to use the DIMM total used free shared buffers cached Mem: 12004 10766 1238 0 384 4809 -/+ buffers/cache: 5572 6432 Swap: 2047 0 2047 iostat output while problem is occuring avg-cpu: %user %nice %system %iowait %steal %idle 52.82 0.00 11.01 0.00 0.00 36.17 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 47.00 0.00 576.00 0 576 sda1 0.00 0.00 0.00 0 0 sda2 1.00 0.00 32.00 0 32 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 46.00 0.00 544.00 0 544 avg-cpu: %user %nice %system %iowait %steal %idle 53.12 0.00 7.81 0.00 0.00 39.06 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 49.00 0.00 592.00 0 592 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 49.00 0.00 592.00 0 592 avg-cpu: %user %nice %system %iowait %steal %idle 56.09 0.00 7.43 0.37 0.00 36.10 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 232.00 0.00 64520.00 0 64520 sda1 0.00 0.00 0.00 0 0 sda2 159.00 0.00 63728.00 0 63728 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 73.00 0.00 792.00 0 792 avg-cpu: %user %nice %system %iowait %steal %idle 52.18 0.00 9.24 0.06 0.00 38.51 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 49.00 0.00 600.00 0 600 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 49.00 0.00 600.00 0 600 avg-cpu: %user %nice %system %iowait %steal %idle 54.82 0.00 8.64 0.00 0.00 36.55 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 100.00 0.00 2168.00 0 2168 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 100.00 0.00 2168.00 0 2168 avg-cpu: %user %nice %system %iowait %steal %idle 54.78 0.00 6.75 0.00 0.00 38.48 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 84.00 0.00 896.00 0 896 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 84.00 0.00 896.00 0 896 avg-cpu: %user %nice %system %iowait %steal %idle 54.34 0.00 7.31 0.00 0.00 38.35 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 81.00 0.00 840.00 0 840 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 81.00 0.00 840.00 0 840 avg-cpu: %user %nice %system %iowait %steal %idle 55.18 0.00 5.81 0.44 0.00 38.58 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 317.00 0.00 105632.00 0 105632 sda1 0.00 0.00 0.00 0 0 sda2 224.00 0.00 104672.00 0 104672 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 93.00 0.00 960.00 0 960 avg-cpu: %user %nice %system %iowait %steal %idle 55.38 0.00 7.63 0.00 0.00 36.98 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 74.00 0.00 800.00 0 800 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 74.00 0.00 800.00 0 800 avg-cpu: %user %nice %system %iowait %steal %idle 56.43 0.00 7.80 0.00 0.00 35.77 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 72.00 0.00 784.00 0 784 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 72.00 0.00 784.00 0 784 avg-cpu: %user %nice %system %iowait %steal %idle 54.87 0.00 6.49 0.00 0.00 38.64 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 80.20 0.00 855.45 0 864 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 80.20 0.00 855.45 0 864 avg-cpu: %user %nice %system %iowait %steal %idle 57.22 0.00 5.69 0.00 0.00 37.09 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 33.00 0.00 432.00 0 432 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 33.00 0.00 432.00 0 432 avg-cpu: %user %nice %system %iowait %steal %idle 56.03 0.00 7.93 0.00 0.00 36.04 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 41.00 0.00 560.00 0 560 sda1 0.00 0.00 0.00 0 0 sda2 2.00 0.00 88.00 0 88 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 39.00 0.00 472.00 0 472 avg-cpu: %user %nice %system %iowait %steal %idle 55.78 0.00 5.13 0.00 0.00 39.09 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 29.00 0.00 392.00 0 392 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 29.00 0.00 392.00 0 392 avg-cpu: %user %nice %system %iowait %steal %idle 53.68 0.00 8.30 0.06 0.00 37.95 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 78.00 0.00 4280.00 0 4280 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 78.00 0.00 4280.00 0 4280

    Read the article

  • Windows XP periodically disconnects, reconnects; Windows 7 doesn't

    - by einpoklum
    My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it doesn't happen. The connection is smooth (OS is sluggish though, but never mind that). Like I said, I updated the NIC driver. I tried reducing the MTU (used something called Dr. TCP), thinking maybe that would help, but it didn't. (I'm a bit but not super-knowledgeable about TCP parameters.) I'm guessing it's either a problem with the driver or some settings which are different between the two OSes. ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM

    Read the article

  • OS Missing? Messed up the MBR on Win7 64-bit

    - by hom3lesshom3boy
    I have a Windows 7 machine with two hard drives: a 1TB C: drive and 500GB J:. I had Windows XP installed on C: and Windows 7 installed on J:. I installed Windows 7 after Windows XP from an installer .exe I (legally) bought and downloaded. It, and all of my other files, are sitting on my J: drive intact. While under my Windows 7 install, a few days ago I decided to use Priform's CCleaner and use its DriveWipe utility to wipe the C: drive. 1% into the process, I cancelled and attempted to use it again. It gives me an error saying it can't format the drive, so I poke around the Internet a bit, give up, and restart my computer. I first get an "OS is missing" error after the computer boots past the BIOS. I downloaded and put UBCD on a bootable USB to use another drivewiping tool to completely erase the C: drive, hoping it'll take the problem with it. No luck. I try to use TestDisk to make my J: my primary active drive, but no luck. I still get the "OS is missing" error. Or sometimes it'll hang at Verifying DMI Pool. Or sometimes I'll get the "NTLDR is missing" error. I get hold of Hiren's and put it on another bootable USB. I first I tried the Boot Windows 7 from Hard Drive option, and I get "Error 15: File Not Found". I tried the "Fix 'NTLDR is Missing'" option (I'm not quite sure why this is even showing up, since I'm trying to get into a HDD with Windows 7 installed. Probably messed up somewhere when I used TestDisk) and I get this list: I'll run through the error messages I get: 1st Try - Windows could not start because the following file is missing or corrupt: \system32\hal.dll 2nd Try - Windows could not start because the following file is missing or corrupt: \system32\ntoskrnl.exe 3rd Try - Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware. 4th - 8th Try - Same as #3 9th Try - I/O Error accessing boot sector file multi(0)disk(0)fdisk(0)\BOOTSEC.DOS. And computer freezes. 10th Try - computer restarts Needless to say, not a single one of those works. I then tried to open up the Windows 7 exe I have sitting on my J: from the Mini-XP OS on Hiren's, but it won't run because I'm trying to run a 64-bit file from a 32-bit exe. At least, that's the problem according to these guys: http://social.technet.microsoft.com/...-b2f54e9c7d18/ I then borrowed a 64-bit Windows Home Premium CD from a friend to get to the recovery options. But I get the error message: This version of System Recovery Options is not compatible with the version of Windows you are trying to repair. Try using a recovery disc that is compatible with this version of Windows. I pressed Shift + F10 to get to the Command Prompt directly. These are the exact steps I took from there (paraphrased a little): X:\Sources>bootrec /Fixmbr The operation completed successfully. X:\Sources>bootrec /Fixboot The operation completed successfully. I restarted my computer, but it still didn't work. I unplugged the C: drive, then tried bootrec and Diskpart: X:\Sources> bootrec.exe X:\Sources> bootrec /RebuildBcd Total identified Windows installations: 1 [1] \\?\GLOBALROOT\Device\HarddiskVolume1\Windows Add installation to bootlist? Yes(Y)/No(N)/All(A):y The requested system device cannot be found. X:\Sources>DiskPart DISKPART> List Disk Disk # Status Size Free Dyn Gpt Disk 0_Online_465GB_0B_______* Disk 1 Online 1000MB 0B (this is Hiren's on a bootable usb) DISKPART> Select Disk 0 Disk 0 is now the selected disk. DISKPART> List Partition Partition # Type Size Offset Partition 1 System 465GB 31KB DISKPART> Select Partition 1 Partition 1 is now the selected partition DISKPART> Active The selected disk is not a fixed MBR disk. The ACTIVE command can only be used on fixed MBR disks. DISKPART> exit Leaving Diskpart... X:\Sources>bootrec /Fixmbr The operation completed successfully. X:\Sources>bootrec /Fixboot The operation completed successfully. Before I go any further, is there anything I'm overlooking/doing wrong? All I care about is making the J: and Windows 7 bootable again. SPECS: Windows 7 Professional 64-Bit GIGABYTE - Motherboard - Socket 775 - GA-P35-DS3R (rev. 2.1) Crucial Ballistix 2048MB PC6400 DDR2 800MHz (2x2GB) Intel Core 2 Duo E6700 Processor (2.6 (6GHZ) I think... not sure anymore C: HDD - SAMSUNG HD103UJ (1TB, not plugged in) J: HDD - WDC WD5000AKS-00V1A0 (500GB)

    Read the article

  • Computer won't reboot without waiting for a while

    - by Benjamin
    I've got an unusual problem with my computer. When ever I reboot my computer it won't boot, I get a few beeps from the BIOS and nothing else, however if I wait for a few minuets the computer will boot perfectly. I tried to count the beeps and I get around 7-9 of them; the first two are noticeably closer together than the rest. [Edit: I'm now reasonably confident it's 1 long followed by 8 short beeps. That would be a display related issue: http://www.bioscentral.com/beepcodes/amibeep.htm] My BIOS is American Megatrends Inc and version P1.80, the Motherboard is an ASRock X58 Extreme (both according to dmidecode) Here's an output from LSPCI, I'm not sure what else might be useful but I can provide whatever's asked. 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) 00:1a.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6 00:1d.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller 02:00.1 IDE interface: VIA Technologies, Inc. VT6415 PATA IDE Host Controller (rev a0) 03:00.0 SATA controller: JMicron Technology Corp. JMB360 AHCI Controller (rev 02) 05:00.0 VGA compatible controller: nVidia Corporation GT200b [GeForce GTX 285] (rev a1) ff:00.0 Host bridge: Intel Corporation Xeon 5500/Core i7 QuickPath Architecture Generic Non-Core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Xeon 5500/Core i7 QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Xeon 5500/Core i7 QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Xeon 5500/Core i7 QPI Physical 0 (rev 05) ff:03.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller (rev 05) ff:03.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Target Address Decoder (rev 05) ff:03.4 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Test Registers (rev 05) ff:04.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Control Registers (rev 05) ff:04.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Address Registers (rev 05) ff:04.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Rank Registers (rev 05) ff:04.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Thermal Control Registers (rev 05) ff:05.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Control Registers (rev 05) ff:05.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Address Registers (rev 05) ff:05.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Rank Registers (rev 05) ff:05.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Thermal Control Registers (rev 05) ff:06.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Control Registers (rev 05) ff:06.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Address Registers (rev 05) ff:06.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Rank Registers (rev 05) ff:06.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Thermal Control Registers (rev 05) Update: ok I installed lm-sensors and here's the output. coretemp-isa-0000 Adapter: ISA adapter Core 0: +58.0°C (high = +80.0°C, crit = +100.0°C) Core 1: +59.0°C (high = +80.0°C, crit = +100.0°C) Core 2: +58.0°C (high = +80.0°C, crit = +100.0°C) Core 3: +57.0°C (high = +80.0°C, crit = +100.0°C) it8720-isa-0a10 Adapter: ISA adapter in0: +0.93 V (min = +0.00 V, max = +4.08 V) in1: +0.06 V (min = +0.00 V, max = +4.08 V) in2: +3.25 V (min = +0.00 V, max = +4.08 V) +5V: +2.91 V (min = +0.00 V, max = +4.08 V) in4: +3.04 V (min = +0.00 V, max = +4.08 V) in5: +2.94 V (min = +0.00 V, max = +4.08 V) in6: +2.14 V (min = +0.00 V, max = +4.08 V) 5VSB: +2.96 V (min = +0.00 V, max = +4.08 V) Vbat: +3.28 V fan1: 1869 RPM (min = 0 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 1106 RPM (min = -1 RPM) fan5: 225000 RPM (min = -1 RPM) temp1: +39.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor temp2: +56.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor temp3: +127.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor cpu0_vid: +1.650 V intrusion0: ALARM If it helps here's the summery from sensors-detect Driver `it87': * ISA bus, address 0xa10 Chip `ITE IT8720F Super IO Sensors' (confidence: 9) Driver `adt7475': * Bus `NVIDIA i2c adapter 3 at 5:00.0' Busdriver `nvidia', I2C address 0x2e Chip `Analog Devices ADT7473' (confidence: 5) Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9)

    Read the article

  • USB Hub and Ubuntu

    - by aserwin
    I have a powered 7 port hub connected to my Ubuntu box and it does nothing. The devices (zip drive and web cam) work direct, but aren't recognized through the hub. This worked fine in Windows 7. I can't prove it is the OS because this is a new motherboard and processor. Any advice? EDIT : Output from lsusb -v Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0002 2.0 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ehci_hcd iProduct 2 EHCI Host Controller iSerial 1 0000:00:12.2 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 5 wHubCharacteristic 0x000a No power switching (usb 1.0) Per-port overcurrent protection bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0503 highspeed power enable connect Port 3: 0000.0100 power Port 4: 0000.0100 power Port 5: 0000.0100 power Device Status: 0x0001 Self Powered Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0002 2.0 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ehci_hcd iProduct 2 EHCI Host Controller iSerial 1 0000:00:13.2 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 5 wHubCharacteristic 0x000a No power switching (usb 1.0) Per-port overcurrent protection bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Port 5: 0000.0100 power Device Status: 0x0001 Self Powered Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0002 2.0 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ehci_hcd iProduct 2 EHCI Host Controller iSerial 1 0000:00:16.2 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x000a No power switching (usb 1.0) Per-port overcurrent protection bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0001 Self Powered Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:12.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 5 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 2 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Port 5: 0000.0100 power Device Status: 0x0001 Self Powered Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:13.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 5 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 2 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Port 5: 0000.0100 power Device Status: 0x0001 Self Powered Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:14.5 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 2 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 2 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Device Status: 0x0001 Self Powered Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:16.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 2 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0303 lowspeed power enable connect Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0001 Self Powered Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 1 Single TT bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0002 2.0 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:02:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 2 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Device Status: 0x0001 Self Powered Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:02:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 31 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 bMaxBurst 0 Hub Descriptor: bLength 12 bDescriptorType 42 nNbrPorts 2 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere bHubDecLat 0.0 micro seconds wHubDelay 0 nano seconds DeviceRemovable 0x00 Hub Port Status: Port 1: 0000.02a0 5Gbps power Rx.Detect Port 2: 0000.02a0 5Gbps power Rx.Detect Binary Object Store Descriptor: bLength 5 bDescriptorType 15 wTotalLength 15 bNumDeviceCaps 1 SuperSpeed USB Device Capability: bLength 10 bDescriptorType 16 bDevCapabilityType 3 bmAttributes 0x00 Latency Tolerance Messages (LTM) Supported wSpeedsSupported 0x0008 Device can operate at SuperSpeed (5Gbps) bFunctionalitySupport 3 Lowest fully-functional device speed is SuperSpeed (5Gbps) bU1DevExitLat 3 micro seconds bU2DevExitLat 2047 micro seconds Device Status: 0x0001 Self Powered Bus 001 Device 002: ID 04a9:1709 Canon, Inc. PIXMA MP150 Scanner Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x04a9 Canon, Inc. idProduct 0x1709 PIXMA MP150 Scanner bcdDevice 1.08 iManufacturer 1 Canon iProduct 2 MP150 iSerial 3 20BC24 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 62 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 2mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 255 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x07 EP 7 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x88 EP 8 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x89 EP 9 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 11 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 7 Printer bInterfaceSubClass 1 Printer bInterfaceProtocol 2 Bidirectional iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 007 Device 002: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x046d Logitech, Inc. idProduct 0xc517 LX710 Cordless Desktop Laser bcdDevice 38.10 iManufacturer 1 Logitech iProduct 2 USB Receiver iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 59 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 98mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 1 Keyboard iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 59 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 177 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) This is with the powered hub plugged in.

    Read the article

  • Actionscript 3: Monitoring the activity level for multiple Microphones doesn't seem to work.

    - by Dave
    For a project I want to show all available webcams and microphones, so that the user can easily select whichever webcam/microphone combination they prefer. I run into an issue with the microphones listing though. Each microphone is listed with an activity animation and it's name. I am able to list all Microphones just fine (using the Microphone.names Array), but it seems like I can only get the activity viewer to work for one microphone. The other microphones show up with '-1' activity, which (as far as I know) is Flex for 'present, but not in use'. When unplugging the microphone that does show activity, the next one (in my case, the mic-in line on my motherboard) shows up with '0' activity (it's not connected, so that makes sense). During my testing I have a total of 3 microphones available, the not-connected onboard mic-in port, and two connected microphones. For testing purposes I use a timer that traces the current microphone activity each 100ms and the graph is also shown. It does not seem to matter what default microphone I set via flash' settings panel. The code I've only attached the revelant code snippets below to make it easier for you to read through them. Please let me know if you prefer the entire code. Main application.mxml Note: cont is a VBox. i is defined before this code snippet. var mics:Array = Microphone.names; for(i=0; i < mics.length; i++){ var mic:settingsMicEntry = new assets.settingsMicEntry; mic.d = {name: mics[i], index: i}; cont.addChild(mic); } assets/settingsMicEntry.mxml timer is defined before this code snippet. the SoundTransform is added to silence local microphone playback. Excluding this code does not solve the problem, sadly (I've tried). display is an MXML Canvas object. mic = Microphone.getMicrophone(d.index); if(mic){ // Temporary: The Microphones' visualizer var bar:Box = new Box(); bar.y = 50; bar.height = 0; bar.width = 66; bar.setStyle("backgroundColor", 0x003300); display.addChild(bar); var tf:SoundTransform = new SoundTransform(0); mic.setLoopBack(true); mic.soundTransform = tf; timer = new Timer(100); timer.addEventListener(TimerEvent.TIMER, function(e:TimerEvent):void{ var h:int = Math.floor((display.height/100)*mic.activityLevel); bar.height = (h>-1) ? h : 0; bar.y = (h>-1) ? display.height-h : display.height; trace('TIMER: '+h+' from '+d.name); }); timer.start(); } I'm pulling my hear out here, so any help is much appreciated! Thanks, -Dave Ps.: Pardon the messiness of the code!

    Read the article

  • Windows periodically disconnects, reconnects to the network

    - by einpoklum
    My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it also happens. (When I initially wrote this question I didn't notice it.) ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM A result of some tests a couple of the disconnects: C:\Documents and Settings\eyalroz.BAKNUNIN>nslookup google.com DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 192.117.235.235: Timed out DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 62.219.186.7: Timed out *** Default servers are not available Server: UnKnown Address: 192.117.235.235 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out C:\Documents and Settings\eyalroz.BAKNUNIN>ping 194.90.1.5 Pinging 194.90.1.5 with 32 bytes of data: Control-C ^C C:\Documents and Settings\eyalroz.BAKNUNIN>tracert -d 194.90.1.5 Tracing route to 194.90.1.5 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.0.254 2 * * 11 ms 10.168.128.1 3 14 ms 13 ms 14 ms 212.179.160.142 4 * * * Request timed out. 5 * * * Request timed out. 6 * * 47 ms 62.219.189.169 7 31 ms 27 ms 32 ms 62.219.189.150 8 15 ms 14 ms 16 ms 192.114.65.202 9 15 ms 15 ms 11 ms 212.143.10.66 10 13 ms 29 ms 31 ms 212.143.12.234 11 35 ms 15 ms 18 ms 212.143.8.72 12 22 ms 22 ms 16 ms 194.90.1.5 I usually ping 194.90.1.5 (which is not at my ISP) with 15ms response time and no losses. Things I've done/tried: [2012-03-26] I replaced the cable; I thought that made a difference, but the disconnects were back a while later, so that wasn't it. Updated the NIC driver. Tried reducing the MTU (used a utility called Dr. TCP); there was no effect. I updated my board BIOS revision (which caused all the HW to be "reinstalled" or re-identified - successfully). I installed another NIC, and tried switching to it - same effect with the on-board NIC. A while back I tried another router (although it was an Edimax model) - same problem. Connected the computer directly, with no router. Same problem. ping -t to the router (192.168.0.254) gives pongs, nothing is lost, and time is < 1 ms almost always (sometimes it says 1 or 2 ms). This is the case also during the disconnects.

    Read the article

  • Why are my hard drives failing?

    - by WishCow
    I have a small Ubuntu server running at home, with 2 HDDs. There are two software raids (raid1) on the disks, managed by mdadm, which I believe is irrelevant, but mentioning it anyway. Both of the HDDs are Western Digital, and have been used for around 2 years, when one of them started making clicking noises, and died. I figured that maybe it's natural after 2 years, so I bought a new one, and resynced the raid arrays. After about a month, the other drive also died. I didn't get suspicious, since both drives have been bought at the same time, it's not that surprising to see both of them near each other, so I bought another one. So far, 2 old drives failed, and 2 brand new in the system. After one month, one of the new drives died. This is when it started getting suspicious. Since the PC was put together from some really old parts (think AthlonXP), I figured that maybe the motherboard's SATA controller is the culprit. Of course you can't switch parts easily in an old PC like this, so I bought a whole system, new MB, new CPU, new RAM. Took the just failed drive back, since it was under warranty, and got it replaced. So it is up to 2 failed drives from the old ones, and 1 failed drive from the new ones. No problems, for 1 month. After that errors were creeping up again in /var/log/messages, and mdadm was reporting raid array failures. I started tearing my hair out. Everything is new in the system, it's up to the third brand new HDD, it's simply not possible that all of the new drives that I bought were faulty. Let's see what is still common... the cables. Okay, long shot, let's replace the SATA cables. Take HDD back, smile to the guy at the counter and say that I'm really unlucky. He replaces the HDD. I come home, one month passes and one of HDDs fails, again. I'm not joking. Two of the brand new HDDs have failed. Maybe it's a bug in the OS. Let's see what the manufacturer's testing tool says. Download testing tool, burn it to a CD, reboot, leave HDD testing overnight. Test says that the drive is faulty, and I should back up everything, if I still can. I don't know what's happening, but it does not look like a software problem, something is definitely thrashing the HDDs. I should mention now, that the whole system is in a shoebox. Since there are a load of "build your own ikea case" stuff, I thought there shouldn't be any problems throwing the thing in a box, and stuffing it away somewhere. The box is well ventilated, but I thought that just maybe the drives were overheating. There is no other possible answer to this. So I took the HDD back, and got it replaced (for the 3rd time), and bought HDD coolers. And just now, I have heard the sound of doom. click click whizzzzzzzzz. SSH into the box: You have new mail! mail r 1 DegradedArrayEvent on /dev/md0 ... dmesg output: [47128.000051] ata3: lost interrupt (Status 0x50) [47128.000097] end_request: I/O error, dev sda, sector 58588863 [47128.000134] md: super_written gets error=-5, uptodate=0 [48043.976054] ata3: lost interrupt (Status 0x50) [48043.976086] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [48043.976132] ata3.00: cmd c8/00:18:bf:40:52/00:00:00:00:00/e1 tag 0 dma 12288 in [48043.976135] res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout) [48043.976208] ata3.00: status: { DRDY } [48043.976241] ata3: soft resetting link [48044.148446] ata3.00: configured for UDMA/133 [48044.148457] ata3.00: device reported invalid CHS sector 0 [48044.148477] ata3: EH complete Recap: No possibility of overheating 6 drives have failed, 4 of those have been brand new. I'm not sure now that the original two have been faulty, or suffered the same thing that the new ones. There is nothing common in the system, apart from the OS which is Ubuntu Karmic now (started with Jaunty). New MB, new CPU, new RAM, new SATA cables. No, the little holes on the HDD are not covered I'm crying. Really. I don't have the face to return to the store now, it's not possible for 4 drives to fail under 4 months. A few ideas that I have been thinking: Is it possible that I fuck up something when I partition and resync the drives? Can it be so bad that it physicaly wrecks the drive? (since the vendor supplied tool says that the drive is damaged) I do the partitoning with fdisk, and use the same block size for the raid1 partitions (I check the exact block sizes with fdisk -lu) Is it possible that the linux kernel or mdadm, or something is not compatible with this exact brand of HDDs, and thrashes them? Is it possible that it may be the shoebox? Try placing it somewhere else? It's under a shelf now, so humidity is not a problem either. Is it possible that a normal PC case will solve my problem (I'm going to shoot myself then)? I will get a picture tomorrow. Am I just simply cursed? Any help or speculation is greatly appreciated. Edit: The power strip is guarded against overvoltage. Edit2: I have moved inbetween these 4 months, so the possibility of the cause being "dirty" electricity in both places, is very low. Edit3: I have checked the voltages in the BIOS (couldn't borrow a multimeter), and they are all seem correct, the biggest discrepancy is in the 12V, because it's supplying 11.3. Should I be worried about that? Edit4: I put my desktop PC's PSU into the server. The BIOS reported much more accurate voltage readings, and also it has successfully rebuilt the raid1 array, which took some 3-4 hours, so I feel a little positive now. Will get a new PSU tomorrow to test with that. Also, attaching the picture about the box: (disregard the 3rd drive)

    Read the article

  • How to make my robot move in a rectangular path along the black tape?

    - by Sahat
    I am working on a robot, it's part of the summer robotics workshop in our college. We are using C-STAMP micro controllers by A-WIT. I was able to make it move, turn left, turn right, move backward. I have even managed to make it go along the black tape using a contrast sensor. I send the robot at 30-45 degrees toward the black tape on the table and it aligns itself and starts to move along the black tape. It jerks a little, probably due to my programming logic below, it's running a while loop and constantly checking if statements, so it ends up trying to turn left and right every few milliseconds, which explains the jerking part. But it's okay, it works, not as smooth as I want it to work but it works! Problem is that I can't make my robot go into a rectangular path of the black tape. As soon as it reaches the corner it just keeps going straight instead of making a left/right turn. Here's my attempt. The following code is just part of the code. My 2 sensors are located right underneath the robot, next to the front wheel, almost at the floor level. It has "index" value ranging from 0 to 8. I believe it's 8 when you have a lot of light coming into the sensor , and 0 when it's nearly pitch black. So when the robot moves into the black-tape-zone, the index value drops, and based on that I have an if-statement telling my robot to either turn left or right. To avoid confusion I didn't post the entire source code, but only the logical part responsible for the movement of my robot along the black tape. while(1) { // don't worry about these. // 10 and 9 represent Sensor's PIN location on the motherboard V = ANALOGIN(10, 1, 0, 0, 0); V2 = ANALOGIN(9, 1, 0, 0, 0); // i got this "formula" from the example in my Manual. // V stands for voltage of the sensor. // it gives me the index value of the sensor. 0 = darkest, 8 = lightest. index = ((-(V - 5) / 5) * 8 + 0.5); index2 = ((-(V2 - 5) / 5) * 8 + 0.5); // i've tweaked the position of the sensors so index > 7 is just right number. // the robot will move anywhere on the table just fine with index > 7. // as soon as it drops to or below 7 (i.e. finds black tape), the robot will // either turn left or right and then go forward. // lp & rp represent left-wheel pin and right-wheel pin, 1 means run forever. // if i change it from 1 to 100, it will go forward for 100ms. if (index > 7 && index2 > 7) goForward(lp, rp, 1); if (index <= 7) { turnLeft(lp, rp, 1); goForward(lp, rp, 1); // this is the tricky part. i've added this code last minute // trying to make my robot turn, but i didn't work. if (index > 4) { turnLeft(lp, rp, 1); goForward(lp, rp, 1); } } else if (index2 <= 7) { turnRight(lp, rp, 1); goForward(lp, rp, 1); // this is also the last minute addition. it's same code as above // but it's for the 2nd sensor. if (index2 > 4) { turnRight(lp, rp, 1); goForward(lp, rp, 1); } } I've spent the entire day trying to figure it out. I've pretty much exhausted all avenues. Asking for the solution on stackoverflow is my very last option now. Thanks in advance! If you have any questions about the code, let me know, but comments should be self-explanatory.

    Read the article

  • Windows 7 intermittently drops wired internet/lan connection.

    - by CraigTP
    In a nutshell, my Windows 7 Ultimate PC intermittently drops it's internet connection. Why? Background: My PC is wired to my ADSL modem/router which is directly connected to the phone line. I also have wireless connectivity turned on within the router for a laptop to connect wirelessly. Every few hours or so, when using my PC, I find I cannot access the internet and pages will not load. Eventually, Windows7 will update the network icon in the task-tray to show the exclamation mark symbol on the network icon. Opening up the Network And Sharing Centre will show the red cross between the "Multiple Networks" and "The Internet". Here's a picture of the "Network And Sharing Centre" (grabbed when everything was working!) As you can see, I'm running Sun's VirtualBox on this machine and that creates a Network connection for itself. This doesn't seem to affect the intermittent dropping (i.e. the intermittent drops occur whether the VirtualBox connection is in use or not). When the connection does drop, I cannot access any internet pages, nor can I access the router's web admin page at http://192.168.1.1/, so I'm assuming I've lost all local LAN access too. It's definitely not the router (or the internet connection itself) as my laptop, using the wireless connection (and running Vista Home Premium) continues to be able to access the internet (and the router's web admin pages) just fine. Every time this happens, I can immediately restore all internet and LAN access by opening Network Adapter page, disabling the "Local Area Connection" and then re-enabling it. Give it a few seconds and everything is fine again. I assume this is because, beneath the GUI, it's effectively doing an "ipconfig /release" then "ipconfig /renew". Why does this happen in the first place, though? I've googled for this and seen quite a few other people (even on MSDN/Technet forums) experiencing the same or almost the same problem, but with no clear resolution. Suggestions of turning off IPv6 on the LAN adapter, and ensuring there's no power management "sleeping" the network adapter have been tried but do not cure the problem. There does not seem to be any particular sequence of events that cause it to happen either. I've had it go twice in 20 minutes when just randomly browsing the web with no other traffic, and I've also had it go once then not go again for 2-3 hours with the same sort of usage. Can anyone tell me why this is happening and how to make it stop? EDIT: Additional information based upon the answer provided so far: Firstly, I forgot the mention that this is Windows 7 64 bit if that makes any difference at all. I mentioned that I don't think the VirtualBox network adpater is causing this problem in any way, and I also have VirtualBox installed on two other machines, one running Vista Home Premium and the other running XP. Neither of these machine experience the same network connectivity issues as the Windows 7 machine. The IP assignment for the Windows 7 machine is the same both before and after the "drop". I have a DHCP server on the router issuing IP Addresses, however my Windows 7 machine uses a static address. Here's the output from "ipconfig": Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.2(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Within the system's event logs, the only event that relates to the connection dropping is a "DNS Client Event" and this is generated after the connection has dropped and is an event detailing that DNS information can't be found for whatever website I may be trying to access, just as the connection drops: Log Name: System Source: Microsoft-Windows-DNS-Client Event ID: 1014 Task Category: None Level: Warning Keywords: User: NETWORK SERVICE Description: Name resolution for the name weather.service.msn.com timed out after none of the configured DNS servers responded. The network adapter chipset is Realtek PCIe GBE Family Controller and I have confirmed that this is the correct chipset for the motherboard (Asus M4A77TD PRO), and in fact, Windows Update installed an updated driver for this on 12/Jan/2009. The details of the update say that it's a Realtek software update from December 2009. Incidentally, I was still having the same intermittent problems prior to this update. It seems to have made no difference at all. EDIT 2 (1 Feb 2010): In my quest to solve this problem, I have discovered some more interesting information. On another forum, someone suggested that I should try running Windows in "Safe Mode With Networking" and see if the problem continues to occur. This was a fantastic suggestion and I don't know why I didn't think of it sooner myself. So, I proceeded to run in Safe Mode with Networking for a number of hours, and amazingly, the "drops" didn't occur once. It was a positive discovery, however, due to the intermittent nature of the original problem, I wasn't completely convinced that the problem was cured. One thing I did note is that the fan on my GFX card was running alot louder than normal. This is due to the fact that I have an ASUS ENGTS250 graphics card (http://www.asus.com/product.aspx?P_ID=B6imcoax3MRY42f3) which had a known problem with a noisy fan until a BIOS update fixed the issue. (See the "Manufacturer Response" here: http://www.newegg.com/Product/Product.aspx?Item=N82E16814121334 for details). Well, running in safe mode had the fan running (incorrectly) at full speed (as it did before the BIOS update), but with an (apparently) stable network connection. Obviously some driver was not loaded for the GFX card when in Safe Mode so this got me thinking about the GFX card (since the very noisy fan was quite obvious when running in Safe Mode). I rebooted into normal mode, and found that Nvidia had a very up-to-date new driver for my GFX card (only about 1 week old), so I downloaded the appropriate driver and installed it. After installation and a reboot, I was able to use my PC for an entire day with NO NETWORK DROPS!!! This was on Saturday. However, on the Sunday, I also had my PC for pretty much the entire day and experienced 2 network drops. No other changes have been made to my PC in this time. So, the story seems to be that updating my graphics card drivers seems to have improved (if not completely fixed) the issue, however, I'm still searching for a proper fix for this problem. Hopefully, this information may help anyone who may have additional ideas as to why this problem is occuring in the first place. (And why does new GFX card drivers have anything to do with the network?) I appreciate everyone's feedback so far. However, I'll have to ask once more if anyone has any further ideas of how to fix this particular problem? Thanks in advance.

    Read the article

  • unexplainable packet drops with 5 ethernet NICs and low traffic on Ubuntu

    - by jon
    I'm stuck on problem where my machine started to drops packets with no sign of ANY system load or high interrupt usage after an upgrade to Ubuntu 12.04. My server is a network monitoring sensor, running Ubuntu LTS 12.04, it passively collects packets from 5 interfaces doing network intrusion type stuff. Before the upgrade I managed to collect 200+GB of packets a day while writing them to disk with around 0% packet loss depending on the day with the help of CPU affinity and NIC IRQ to CPU bindings. Now I lose a great deal of packets with none of my applications running and at very low PPS rate which a modern workstation NIC would have no trouble with. Specs: x64 Xeon 4 cores 3.2 Ghz 16 GB RAM NICs: 5 Intel Pro NICs using the e1000 driver (NAPI). [1] eth0 and eth1 are integrated NICs (in the motherboard) There are 2 other PCI-X network cards, each with 2 Ethernet ports. 3 of the interfaces are running at Gigabit Ethernet, the others are not because they're attached to hubs. Specs: [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm uptime 17:36:00 up 1:43, 2 users, load average: 0.00, 0.01, 0.05 # uname -a Linux nms 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I also have the CPU governor set to performance mode and irqbalance off. The problem still occurs with them on. # lspci -t -vv -[0000:00]-+-00.0 Intel Corporation E7520 Memory Controller Hub +-02.0-[01-03]--+-00.0-[02]----0e.0 Dell PowerEdge Expandable RAID controller 4 | \-00.2-[03]-- +-04.0-[04]-- +-05.0-[05-07]--+-00.0-[06]----07.0 Intel Corporation 82541GI Gigabit Ethernet Controller | \-00.2-[07]----08.0 Intel Corporation 82541GI Gigabit Ethernet Controller +-06.0-[08-0a]--+-00.0-[09]--+-04.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | | \-04.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-00.2-[0a]--+-02.0 Digium, Inc. Wildcard TE210P/TE212P dual-span T1/E1/J1 card 3.3V | +-03.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-03.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) +-1d.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 +-1d.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 +-1d.2 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 +-1d.7 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller +-1e.0-[0b]----0d.0 Advanced Micro Devices [AMD] nee ATI RV100 QY [Radeon 7000/VE] +-1f.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge \-1f.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller I believe the NIC nor the NIC drivers are dropping the packets because ethtool reports 0 under rx_missed_errors and rx_no_buffer_count for each interface. On the old system, if it couldn't keep up this is where the drops would be. I drop packets on multiple interfaces just about every second, usually in small increments of 2-4. I tried all these sysctl values, I'm currently using the uncommented ones. # cat /etc/sysctl.conf # high net.core.netdev_max_backlog = 3000000 net.core.rmem_max = 16000000 net.core.rmem_default = 8000000 # defaults #net.core.netdev_max_backlog = 1000 #net.core.rmem_max = 131071 #net.core.rmem_default = 163480 # moderate #net.core.netdev_max_backlog = 10000 #net.core.rmem_max = 33554432 #net.core.rmem_default = 33554432 Here's an example of an interface stats report with ethtool. They are all the same, nothing is out of the ordinary ( I think ), so I'm only going to show one: ethtool -S eth2 NIC statistics: rx_packets: 7498 tx_packets: 0 rx_bytes: 2722585 tx_bytes: 0 rx_broadcast: 327 tx_broadcast: 0 rx_multicast: 1504 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 1504 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 0 tx_tcp_seg_failed: 0 rx_flow_control_xon: 0 rx_flow_control_xoff: 0 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 2722585 rx_csum_offload_good: 0 rx_csum_offload_errors: 0 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 01 # ifconfig eth0 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:373348 errors:16 dropped:95 overruns:0 frame:16 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:356830572 (356.8 MB) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8d UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:13616 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8690528 (8.6 MB) TX bytes:0 (0.0 B) eth2 Link encap:Ethernet HWaddr 00:04:23:e1:77:6a UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:7750 errors:0 dropped:471 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2780935 (2.7 MB) TX bytes:0 (0.0 B) eth3 Link encap:Ethernet HWaddr 00:04:23:e1:77:6b UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:5112 errors:0 dropped:206 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:639472 (639.4 KB) TX bytes:0 (0.0 B) eth4 Link encap:Ethernet HWaddr 00:04:23:b6:35:6c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:961467 errors:0 dropped:935 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:958561305 (958.5 MB) TX bytes:0 (0.0 B) eth5 Link encap:Ethernet HWaddr 00:04:23:b6:35:6d inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4264 errors:0 dropped:16 overruns:0 frame:0 TX packets:699 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:572228 (572.2 KB) TX bytes:124456 (124.4 KB) I tried the defaults, then started to play around with settings. I wasn't using any flow control and I increased the RxDescriptor count to 4096 before the upgrade as well without any problems. # cat /etc/modprobe.d/e1000.conf options e1000 XsumRX=0,0,0,0,0 RxDescriptors=4096,4096,4096,4096,4096 FlowControl=0,0,0,0,0 debug=16 Here's my network configuration file, I turned off checksumming and various offloading mechanisms along with setting CPU affinity with heavy use interfaces getting an entire CPU and light use interfaces sharing a CPU. I used these settings prior to the upgrade without problems. # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet manual pre-up /sbin/ethtool -G eth0 rx 4096 tx 0 pre-up /sbin/ethtool -K eth0 gro off gso off rx off pre-up /sbin/ethtool -A eth0 rx off autoneg off up ifconfig eth0 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/48/smp_affinity down ifconfig eth0 down post-down /sbin/ethtool -G eth0 rx 256 tx 256 post-down /sbin/ethtool -K eth0 gro on gso on rx on post-down /sbin/ethtool -A eth0 rx on autoneg on auto eth1 iface eth1 inet manual pre-up /sbin/ethtool -G eth1 rx 4096 tx 0 pre-up /sbin/ethtool -K eth1 gro off gso off rx off pre-up /sbin/ethtool -A eth1 rx off autoneg off up ifconfig eth1 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/49/smp_affinity down ifconfig eth1 down post-down /sbin/ethtool -G eth1 rx 256 tx 256 post-down /sbin/ethtool -K eth1 gro on gso on rx on post-down /sbin/ethtool -A eth1 rx on autoneg on auto eth2 iface eth2 inet manual pre-up /sbin/ethtool -G eth2 rx 4096 tx 0 pre-up /sbin/ethtool -K eth2 gro off gso off rx off pre-up /sbin/ethtool -A eth2 rx off autoneg off up ifconfig eth2 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "1" > /proc/irq/82/smp_affinity down ifconfig eth2 down post-down /sbin/ethtool -G eth2 rx 256 tx 256 post-down /sbin/ethtool -K eth2 gro on gso on rx on post-down /sbin/ethtool -A eth2 rx on autoneg on auto eth3 iface eth3 inet manual pre-up /sbin/ethtool -G eth3 rx 4096 tx 0 pre-up /sbin/ethtool -K eth3 gro off gso off rx off pre-up /sbin/ethtool -A eth3 rx off autoneg off up ifconfig eth3 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "2" > /proc/irq/83/smp_affinity down ifconfig eth3 down post-down /sbin/ethtool -G eth3 rx 256 tx 256 post-down /sbin/ethtool -K eth3 gro on gso on rx on post-down /sbin/ethtool -A eth3 rx on autoneg on auto eth4 iface eth4 inet manual pre-up /sbin/ethtool -G eth4 rx 4096 tx 0 pre-up /sbin/ethtool -K eth4 gro off gso off rx off pre-up /sbin/ethtool -A eth4 rx off autoneg off up ifconfig eth4 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/77/smp_affinity down ifconfig eth4 down post-down /sbin/ethtool -G eth4 rx 256 tx 256 post-down /sbin/ethtool -K eth4 gro on gso on rx on post-down /sbin/ethtool -A eth4 rx on autoneg on auto eth5 iface eth5 inet static pre-up /etc/fw.conf address 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 192.168.1.2 192.168.1.3 up ifconfig eth5 up post-up echo "8" > /proc/irq/77/smp_affinity down ifconfig eth5 down Here's a few examples of packet drops, i ran one after another, probabling totaling 3 or 4 seconds. You can see increases in the drops from the 1st and 3rd. This was a non-busy time, very little traffic. # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 505 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 507 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 227 lo: 0 eth2: 512 eth1: 0 eth5: 17 eth0: 105 eth4: 1039 I tried the pci=noacpi options. With and without, it's the same. This is what my interrupt stats looked like before the upgrade, after, with ACPI on PCI it showed multiple NICs bound to an interrupt and shared with other devices such as USB drives which I didn't like so I think i'm going to keep it with ACPI off as it's easier to designate sole purpose interrupts. Is there any advantage I would have using the default i.e. ACPI w/ PCI. ? # cat /etc/default/grub | grep CMD_LINE GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 noacpi pci=noacpi" GRUB_CMDLINE_LINUX="" # cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 0: 45 0 0 16 IO-APIC-edge timer 1: 1 0 0 7936 IO-APIC-edge i8042 2: 0 0 0 0 XT-PIC-XT-PIC cascade 6: 0 0 0 3 IO-APIC-edge floppy 8: 0 0 0 1 IO-APIC-edge rtc0 9: 0 0 0 0 IO-APIC-edge acpi 12: 0 0 0 1809 IO-APIC-edge i8042 14: 1 0 0 4498 IO-APIC-edge ata_piix 15: 0 0 0 0 IO-APIC-edge ata_piix 16: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb2 18: 0 0 0 1350 IO-APIC-fasteoi uhci_hcd:usb4, radeon 19: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb3 23: 0 0 0 4099 IO-APIC-fasteoi ehci_hcd:usb1 38: 0 0 0 61963 IO-APIC-fasteoi megaraid 48: 0 0 1002319 4 IO-APIC-fasteoi eth0 49: 0 0 38772 3 IO-APIC-fasteoi eth1 77: 0 0 130076 432159 IO-APIC-fasteoi eth4 78: 0 0 0 23917 IO-APIC-fasteoi eth5 82: 1329033 0 0 4 IO-APIC-fasteoi eth2 83: 0 4886525 0 6 IO-APIC-fasteoi eth3 NMI: 5 6 4 5 Non-maskable interrupts LOC: 61409 57076 64257 114764 Local timer interrupts SPU: 0 0 0 0 Spurious interrupts IWI: 0 0 0 0 IRQ work interrupts RES: 17956 25333 13436 14789 Rescheduling interrupts CAL: 22436 607 539 478 Function call interrupts TLB: 1525 1458 4600 4151 TLB shootdowns TRM: 0 0 0 0 Thermal event interrupts THR: 0 0 0 0 Threshold APIC interrupts MCE: 0 0 0 0 Machine check exceptions MCP: 16 16 16 16 Machine check polls ERR: 0 MIS: 0 Here's sample output of vmstat, showing the system. Barebones system right now. root@nms:~# vmstat -S m 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 14992 192 1029 0 0 56 2 419 29 1 0 99 0 0 0 0 14992 192 1029 0 0 0 0 922 27 0 0 100 0 0 0 0 14991 192 1029 0 0 0 36 763 50 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 646 35 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 722 54 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 793 27 0 0 100 0 ^C Here's dmesg output. I can't figure out why my PCI-X slots are negotiated as PCI. The network cards are all PCI-X with the exception of the integrated NICs that came with the server. In the output below it looks as if eth3 and eth2 negotiated at PCI-X speeds rather than PCI:66Mhz. Wouldn't they all drop to PCI:66Mhz? If your integrated NICs are PCI, as labeled below (eth0,eth1), then wouldn't all devices on your bus speed drop down to that slower bus speed? If not, I still don't know why only one of my NICs ( each has two ethernet ports) is labeled as PCI-X in the output below. Does that mean it is running at PCI-X speeds are is it showing that it's capable? # dmesg | grep e1000 [ 3678.349337] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 3678.349342] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3678.349394] e1000 0000:06:07.0: PCI->APIC IRQ transform: INT A -> IRQ 48 [ 3678.409725] e1000 0000:06:07.0: Receive Descriptors set to 4096 [ 3678.409730] e1000 0000:06:07.0: Checksum Offload Disabled [ 3678.409734] e1000 0000:06:07.0: Flow Control Disabled [ 3678.586409] e1000 0000:06:07.0: eth0: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8c [ 3678.586419] e1000 0000:06:07.0: eth0: Intel(R) PRO/1000 Network Connection [ 3678.586642] e1000 0000:07:08.0: PCI->APIC IRQ transform: INT A -> IRQ 49 [ 3678.649854] e1000 0000:07:08.0: Receive Descriptors set to 4096 [ 3678.649859] e1000 0000:07:08.0: Checksum Offload Disabled [ 3678.649863] e1000 0000:07:08.0: Flow Control Disabled [ 3678.826436] e1000 0000:07:08.0: eth1: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8d [ 3678.826444] e1000 0000:07:08.0: eth1: Intel(R) PRO/1000 Network Connection [ 3678.826627] e1000 0000:09:04.0: PCI->APIC IRQ transform: INT A -> IRQ 82 [ 3679.093266] e1000 0000:09:04.0: Receive Descriptors set to 4096 [ 3679.093271] e1000 0000:09:04.0: Checksum Offload Disabled [ 3679.093275] e1000 0000:09:04.0: Flow Control Disabled [ 3679.130239] e1000 0000:09:04.0: eth2: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6a [ 3679.130246] e1000 0000:09:04.0: eth2: Intel(R) PRO/1000 Network Connection [ 3679.130449] e1000 0000:09:04.1: PCI->APIC IRQ transform: INT B -> IRQ 83 [ 3679.397312] e1000 0000:09:04.1: Receive Descriptors set to 4096 [ 3679.397318] e1000 0000:09:04.1: Checksum Offload Disabled [ 3679.397321] e1000 0000:09:04.1: Flow Control Disabled [ 3679.434350] e1000 0000:09:04.1: eth3: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6b [ 3679.434360] e1000 0000:09:04.1: eth3: Intel(R) PRO/1000 Network Connection [ 3679.434553] e1000 0000:0a:03.0: PCI->APIC IRQ transform: INT A -> IRQ 77 [ 3679.704072] e1000 0000:0a:03.0: Receive Descriptors set to 4096 [ 3679.704077] e1000 0000:0a:03.0: Checksum Offload Disabled [ 3679.704081] e1000 0000:0a:03.0: Flow Control Disabled [ 3679.738364] e1000 0000:0a:03.0: eth4: (PCI:33MHz:64-bit) 00:04:23:b6:35:6c [ 3679.738371] e1000 0000:0a:03.0: eth4: Intel(R) PRO/1000 Network Connection [ 3679.738538] e1000 0000:0a:03.1: PCI->APIC IRQ transform: INT B -> IRQ 78 [ 3680.046060] e1000 0000:0a:03.1: eth5: (PCI:33MHz:64-bit) 00:04:23:b6:35:6d [ 3680.046067] e1000 0000:0a:03.1: eth5: Intel(R) PRO/1000 Network Connection [ 3682.132415] e1000: eth0 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.224423] e1000: eth1 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.316385] e1000: eth2 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.408391] e1000: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.500396] e1000: eth4 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.708401] e1000: eth5 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX At first I thought it was the NIC drivers but I'm not so sure. I really have no idea where else to look at the moment. Any help is greatly appreciated as I'm struggling with this. If you need more information just ask. Thanks! [1]http://www.cs.fsu.edu/~baker/devices/lxr/http/source/linux/Documentation/networking/e1000.txt?v=2.6.11.8 [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm

    Read the article

  • Weird WLAN connection

    - by tuelsch
    I assembled my first computer on my own. As I realised it had no WLAN (AsRock Z77 Extreme 4m) I bought a WLAN stick (ZyXel NWD 2105), plugged it in, started the setup from the CD and it worked, until I restarted the PC. That's when the problems started. The stick is able to connect to the router (P-660HN-F1Z) and the connection is stable, but not the internet access. In estimately 1 minute intervals there might be a short connection timeframe and dropbox or windows update are able to download some data, but as soon as I try to open a website the internet access is away. Note that the connection to the router does not shut down and remains stable at around 80-90%. The problem is definetly located on my pc, because with my laptop and phone the connection is stable and fast. Because I was so pissed off, I bought a EW-7612PIn V2 (PCI-E WLAN adapter), same problem. Now the weird thing is, if I don't use the PC for about 2 days, start it up, there is internet access (happened with both the stick and the PCI-E card). A bit slow, but it does not get away just like that, until I shut it down. Then, no matter how many times I restart, it won't come back. I googled a lot but now I'm at the end with my latin. Has anyone had a similar problem and resolved it? Technical details: Motherboard: AsRock Z77 Extreme 4M OS: Windows 7 professional 64bit Stick: Zyxel wireless N adapter NWD2105 PCI-E card: Edimax EW-7612PIn V2 Router: ZyXel P-660HN-F1Z Windows-IP-Konfiguration Hostname . . . . . . . . . . . . : xyz Primäres DNS-Suffix . . . . . . . : Knotentyp . . . . . . . . . . . . : Hybrid IP-Routing aktiviert . . . . . . : Nein WINS-Proxy aktiviert . . . . . . : Nein Drahtlos-LAN-Adapter Drahtlosnetzwerkverbindung 5: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter # 3 Physikalische Adresse . . . . . . : 80-1F-02-61-C0-A6 DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Drahtlos-LAN-Adapter Drahtlosnetzwerkverbindung 4: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Edimax 802.11n Wireless Adapter Physikalische Adresse . . . . . . : 80-1F-02-61-C0-A6 DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Verbindungslokale IPv6-Adresse . : fe80::38d2:f489:726d:1fb5%17(Bevorzugt) IPv4-Adresse . . . . . . . . . . : 192.168.1.41(Bevorzugt) Subnetzmaske . . . . . . . . . . : 255.255.255.0 Lease erhalten. . . . . . . . . . : Donnerstag, 15. November 2012 10:51:05 Lease läuft ab. . . . . . . . . . : Sonntag, 18. November 2012 10:51:18 Standardgateway . . . . . . . . . : 192.168.1.1 DHCP-Server . . . . . . . . . . . : 192.168.1.1 DHCPv6-IAID . . . . . . . . . . . : 578821890 DHCPv6-Client-DUID. . . . . . . . : 00-01-00-01-17-FF-D5-FE-BC-5F-F4-48-FC-4B DNS-Server . . . . . . . . . . . : 91.233.182.2 194.230.1.39 NetBIOS über TCP/IP . . . . . . . : Aktiviert Tunneladapter isatap.{263BEB98-344B-435C-888F-1B15B97C3AC1}: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft-ISATAP-Adapter Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja Tunneladapter Teredo Tunneling Pseudo-Interface: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja IPv6-Adresse. . . . . . . . . . . : 2001:0:9d38:6ab8:209c:2944:3f57:fed6(Bevo rzugt) Verbindungslokale IPv6-Adresse . : fe80::209c:2944:3f57:fed6%11(Bevorzugt) Standardgateway . . . . . . . . . : :: NetBIOS über TCP/IP . . . . . . . : Deaktiviert C:\Users\xyz>ping 192.168.1.1 Ping wird ausgeführt für 192.168.1.1 mit 32 Bytes Daten: Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Ping-Statistik für 192.168.1.1: Pakete: Gesendet = 4, Empfangen = 4, Verloren = 0 (0% Verlust), Ca. Zeitangaben in Millisek.: Minimum = 2ms, Maximum = 2ms, Mittelwert = 2ms

    Read the article

< Previous Page | 58 59 60 61 62