Search Results

Search found 3766 results on 151 pages for 'singleton scope'.

Page 62/151 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

  • Routing table on Linux not respected

    - by MRHaarmann
    I have a very specific problem, building a Linux VPN endpoint (with external VPN Gateway), which should route certain networks over the tunnel, others via default gateway. The Linux VPN should do a NAT on the outgoing connections for the VPN peers. Setup is as following: Internet gateway LAN 192.168.25.1/24 VPN Gateway LAN 10.45.99.2/24 (VPN tunnel 10.45.99.1 to net 87.115.17.40/29, separate connection to Internet) Linux VPN Router eth0 192.168.25.71/24 eth0:503 10.45.99.1/24 Default 192.168.25.1 route to 87.115.17.40/29 via 10.45.99.2 (send_redirects disabled, ip_forward enabled) Linux clients (multiple): eth0 192.168.25.x/24 Default 192.168.25.1 route to 87.115.17.40/29 via 192.168.25.71 Ping to the machines via tunnel from the VPN Router is working. Now I want to establish a routing from my clients over the VPN gateway and the client packet gets routed to 192.168.25.1 ! traceroute output shows the packets get routed to 192.168.25.71, but then to 192.168.25.1. So the route is not respected in forward ! IPTables and Routing: ip route show 87.115.17.40/29 via 10.45.99.2 dev eth0 10.45.99.0/24 dev eth0 proto kernel scope link src 10.45.99.1 192.168.25.0/24 dev eth0 proto kernel scope link src 192.168.25.71 default via 192.168.25.1 dev eth0 iptables -A INPUT -i eth0:503 -j REJECT iptables -t nat -A POSTROUTING -o eth0:503 -j MASQUERADE iptables -A FORWARD -i eth0:503 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 192.168.25.0/24 -o eth0:503 -j ACCEPT So what is wrong with my setup ? The route is chosen correctly from localhost, but all the clients get forwarded to the Internet GW. thanks for helping, Marcus

    Read the article

  • UDP blocked by Windows XP Firewall when sending to local machine

    - by user36367
    I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: Windows XP Professional with Service Pack 3, all updated Program that sends UDP datagrams Program that receives UDP datagrams Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas?

    Read the article

  • UDP blocked by Windows XP Firewall when sending to local machine

    - by user36367
    Hi there, I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: - Windows XP Professional with Service Pack 3, all updated - Program that sends UDP datagrams - Program that receives UDP datagrams - Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas? Thanks in advance!

    Read the article

  • Is there a standard method for assigning nameservers to servers in a Windows domain?

    - by HopelessN00b
    As the title asks, I'm wondering if there's any standard or "best practice" for how to actually assign nameservers (DNS) and manage the nameserver configuration for client servers on a Windows domain. I'm talking about the setting circled in the below image, in case the language of the question is not clear enough: This is for a large, multi-site environment, where ideally/hopefully all servers point at their site's Domain Controller as the primary DNS server, and a DNS server at a different site as the secondary DNS server. For simplicity's sake, we can say that the secondary server would be the Domain Controller at the home site for everyone, and there are no tertiary DNS servers (even though that's not actually the case). Try as I might, I can't seem to find a GPO setting for this (at least on FL 2003 R2, the Computer Configuration - Administrative Templates - Network - DNS Client - DNS Servers GPO is Supported on: Windows XP Professional only), and I find it rather hard to believe that the "best"/"standard" solution would therefore be either scripting up something to apply the DNS settings per site, or using a DHCP server to push those configurations out to the other servers via the DHCP Scope Options. So, is there a standard way of managing this configuration? (That's hopefully not "a script" or "DHCP Scope Option.)

    Read the article

  • IPTables forward from only one ip on my server

    - by user1307079
    I was able to get my server to forward connections on a certain port to a different IP, but when I add -d to specify an IP to froward from, It does not work. This is what I am trying, iptables -t nat -A PREROUTING -d 173.208.230.107 -p tcp --dport 80 iptables -t nat -nvL-j DNAT --to-destination 38.105.20.226:80. It works fine without the -d. Here is my ifconfig dump: em1 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.106 Bcast:173.208.230.111 Mask:255.255.255.248 inet6 addr: fe80::2a0:d1ff:feed:d054/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:100058 errors:0 dropped:0 overruns:0 frame:0 TX packets:18941701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12779711 (12.1 MiB) TX bytes:825498499 (787.2 MiB) Memory:fbde0000-fbe00000 em1:9 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.107 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:10 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.108 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:11 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.109 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:12 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.110 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    Read the article

  • Route web traffic through a separate iterface

    - by tkane
    I'd like to route web traffic through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

    Read the article

  • SSH Connection Error : No route to host

    - by dewbot
    There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

    Read the article

  • Ubuntu - wireless connection works great but wired is totally dead

    - by Dan
    I am running Ubuntu 10.04 on my Acer Aspire One netbook. The wireless connection works great, but the wired is totally dead. When I plug the Ethernet wire, the little led next to the port doesn't blink. If I do ifconfig, this is the output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1659 errors:0 dropped:0 overruns:0 frame:0 TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:132304 (132.3 KB) TX bytes:132304 (132.3 KB) wlan0 Link encap:Ethernet HWaddr 18:f4:6a:65:48:1f inet addr:192.168.1.7 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::1af4:6aff:fe65:481f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:94823 errors:0 dropped:0 overruns:0 frame:0 TX packets:81390 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:93028474 (93.0 MB) TX bytes:18002558 (18.0 MB) There is no eth0. Is that normal? In the "Network Connections" GUI there is an entry "Wired connection 1", its "MAC address" field is blank. How can I make the wired connection work?

    Read the article

  • "Network is unreachable" When pinging google, can connect to internal computers on debian VM

    - by musher
    Similar to this SU question: "Network is unreachable" when attempting to ping google, but internal addresses work Actually, it's pretty much the same base issue. I went through that thread trying to find a solution, I changed my resolv.conf: before: domain [my work domain] search [my work domain] nameserver [my gateway] nameserver [my gateway2] I changed it to: after: domain [my work domain] search [my work domain] nameserver 8.8.8.8 nameserver 8.8.4.4 However, any time I reboot the computer the resolv.conf gets overwritten to the previous version (the 'before' above). The issues began after I installed virtualbox additions, X server and (specifically) LXDE: Cat of apt history.log: Start-Date: 2014-08-21 10:03:42 Commandline: apt-get install virtualbox-guest-utils virtualbox-guest-dkms Install: x11-xkb-utils:amd64 (7.7+1, automatic), libxaw7:amd64 (1.0.12-2, automatic), xfonts-utils:$ End-Date: 2014-08-21 10:03:56 Start-Date: 2014-08-21 10:18:39 Commandline: apt-get install lxde Install: desktop-base:amd64 (7.0.3, automatic), libgoa-1.0-0b:amd64 (3.12.4-1, automatic), lxmenu-d$ End-Date: 2014-08-21 10:21:52 Start-Date: 2014-08-21 10:26:40 Commandline: apt-get upgrade Upgrade: libio-socket-ssl-perl:am ifconfig on the guest: root@Peridot:~# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:89:c9:20 og inet addr:172.31.2.102 Bcast:172.31.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe89:c920/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2281 errors:0 dropped:1 overruns:0 frame:0 TX packets:463 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:266507 (260.2 KiB) TX bytes:120554 (117.7 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) The adapter in VBox is a bridged adapter directly onto my ethernet connection; as are my other 2 VMs (which work) Other SU questions I've tried: "connect: Network is unreachable" in VirtualBox VM

    Read the article

  • Route web browsing through a separate iterface

    - by tkane
    I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

    Read the article

  • SSH not working through Double NAT

    - by d_inevitable
    I am trying to setup port forwarding for ssh through 2 NATs The first Router translates my internet IP to my outer network (10.1.7.0). In the outer network there's a second Router that does NAT to my inner network (192.168.1.0). The target server is connected to both, the outer network and the inner network. I cannot change the port forwarding options for outer router. It is currently configured to forward the SSH and HTTP port to the router for the inner network. Internet + | v +-----------------+ +------------------+ | Outer Router | | Inner Router | |-----------------| |------------------| | | SSH HTTP | | +----+ +--------------------->| | | | | | | | | | | | | +-------+---------+ +------+---------+-+ | | | | | | | | | | | | | | +------------------+ | SSH | | | | Server | | | | | |------------------| | | | +-----------> |<-------+ | | | | |HTTP (testing) | +------------------+ | | | +------v------------------+ | | Outer Workstation | +-------------------+ | |-------------------------| | Inner Workstation| | | | |-------------------| | | | | |<----------------+ +-------------------------+ | | +-------------------+ When connecting from a outer workstation to the address of the inner router, then both SSH and HTTP work fine. When connecting from the internet to my public ip with HTTP, the connection works fine as well. However SSH just times out. Most likely because the reply is not routed back properly. I suspect its either because of the SSH itself, or because the server is connected to both, the inner and outer network. Any ideas how I could resolve this issue? The routes on the server are currently: ip route show default via 10.1.7.254 dev eth0 metric 100 10.1.7.0/24 dev eth0 proto kernel scope link src 10.1.7.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.2 Do I have to change this? If so how?

    Read the article

  • Separated virtual networks with same subnet range with 2 interface

    - by Coolpet
    I'm having some problems with routing with the following: I have a server with 2 interfaces. It has 1-1 alias contains the same subnet. the 2 interface is connected to 2 switch, which are separated from each other. Infrastructure: Eth0 192.168.16.2/20 Eth0:eth0 192.168.1.222/20 Eth1 192.168.32.3/20 Eth1:eth1 192.168.1.223/20 I have a PC which has the IP address: 192.168.1.3/24 The problem is the next: If PC is on subnet 1, I can ping it. If PC is on subnet 2, I can't ping it. traceroute shows the route is across 192.168.1.222 ping -I 192.168.1.223 192.168.1.3 is not working on subnet 2. arp entries show the MAC address belonging to the correct interface (eth1 on subnet 2) How can I force the server to look on both interface same ranged subnet for specific IP? It searches only in the first subnet. The routing table has these 2 entries: 192.168.0.0/20 dev eth0 proto kernel scope link src 192.168.1.222 192.168.0.0/20 dev eth1 proto kernel scope link src 192.168.1.223

    Read the article

  • No outbound internet connection after restarting CentOS 6.3

    - by wnstnsmth
    After restarting a headless CentOS 6.3 machine, it lost outbound internet connectivity, i.e. I can still connect to the server via SSH (ssh root@**.126.18.56), but stuff such as ping google.com gives google.com: unknown host, and yum list some_package gives a lot of network errors. This is what ifconfig gives: eth0 Link encap:Ethernet HWaddr 00:25:90:78:2D:5D inet addr:**.126.18.56 Bcast:**.126.18.255 Mask:255.255.255.0 inet6 addr: fe80::225:90ff:fe78:2d5d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:75594 errors:0 dropped:0 overruns:0 frame:0 TX packets:787 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7074741 (6.7 MiB) TX bytes:144391 (141.0 KiB) Interrupt:20 Memory:f7a00000-f7a20000 eth1 Link encap:Ethernet HWaddr 00:25:90:78:2D:5C UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:16 Memory:f7900000-f7920000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:504 (504.0 b) TX bytes:504 (504.0 b) I have absolutely no clue how to debug this, and I find it very strange since I can still connect via ssh. EDIT: Weirdly, /etc/resolv.conf does not contain any entries, or none that I can make sense of: # Generated by NetworkManager search sui-inter.net # No nameservers found; try putting DNS servers into your # ifcfg files in /etc/sysconfig/network-scripts like so: # # DNS1=xxx.xxx.xxx.xxx # DNS2=xxx.xxx.xxx.xxx # DOMAIN=lab.foo.com bar.foo.com So is it possible that rebooting the server erased that file? It worked before at least! And how do I solve this? By the way, pinging an IP address works.

    Read the article

  • Setup Apache with IPv6

    - by mrz
    I have two virtual machine on my computer. I have Apache installed on one of them (would be referred to as "server" after this), and I have set the Apache to listen to an IPv6. And when I enter the IPv6 into web browser on the "server" I see my index.html file. so far so good ... I want to be able to open a web browser on the other virtual machine("client") and see the index.html. But, when I try entering the IPv6 of the "server" in a web browser on the "client" I get an Unable to establish a connection to the server error. I can ping6 "client" from "server" and vice verse. There is only one thing to mention. ifconfig of the "server" shows 3 different IPv6 which two of them are scoped Global and there is one Link scope IPv6. On the "client" there is only one Link scope IPv6 though. I only can ping the Link IPv6s. Pinging other IPv6s would result connect:Network is unreachable. And if I set Apache to listen to Link IPv6, The rcapache2 start will fail the job. Any thoughts on what I am probably missing/doing wrong?

    Read the article

  • How to set up vpn tunnel (ipsec) connection

    - by Alfwed
    I'm working with a client who wants to set up a vpn tunnel between their network and ours. They're in charge of the tunnel and to give us the access they are asking me my public IP and my LAN IP. This is what i've got when i do an ifconfig on the server i will use to connect to the vpn $ ifconfig eth0 Link encap:Ethernet HWaddr d4:ae:52:cd:xx:xx inet adr:62.210.xxx.xxx Bcast:62.210.xxx.xxx Masque:255.255.255.0 adr inet6: fe80::d6ae:52ff:xxxx:xx/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:55255032 erreurs:0 :779628 overruns:0 frame:0 TX packets:5419527 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:5598164393 (5.5 GB) Octets transmis:1034297288 (1.0 GB) Interruption:16 Mémoire:c0000000-c0012800 lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 Packets reçus:45923382 erreurs:0 :0 overruns:0 frame:0 TX packets:45923382 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 The inet adr:62.210.xxx.xxx is my public IP but it seems like i dont have any LAN IP. Can the connection work without LAN IP or should I create a private network somehow?

    Read the article

  • Struts 1 ActionForm - retrieving a collection from pure HTML

    - by Yaneeve
    Hi all I have (just like the rest) inherited some struts 1 code. I have had need to add a few more pages to this project. What I cannot figure out is how to map several distinct but similarly natured input elements to the my ActionForm. Let me elaborate. I create a new <Input> element dynamically as the user inputs more and more items (I use the YUI autocomplete form element and for each entered input I add it as an input element to my form and draw a new YUI autocomplete - complex sounding, I know) So... My form looks a bit like (... after some prettifying and some such...): <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN" "http://www.w3.org/TR/html4/strict.dtd"> <html> <head> <meta http-equiv="content-type" content="text/html; charset=utf-8"> <title>My Cool App - Test Case Builder</title> <link rel="stylesheet" type="text/css" href="../script/yui/fonts/fonts-min.css" /> <link rel="stylesheet" type="text/css" href="../skins/myCoolApp/button/button.css" /> <link rel="stylesheet" type="text/css" href="../script/yui/autocomplete/assets/skins/sam/autocomplete.css" /> <link rel="stylesheet" type="text/css" media="screen" href="../skins/myCoolApp/testcase.css" /> <!-- YUI JAVA SCRIPTS --> <script type="text/javascript" src="../script/yui/yahoo-dom-event/yahoo-dom-event.js"></script> <script type="text/javascript" src="../script/yui/element/element-min.js"></script> <script type="text/javascript" src="../script/yui/button/button-min.js"></script> <script type="text/javascript" src="../script/yui/datasource/datasource-min.js"></script> <script type="text/javascript" src="../script/yui/autocomplete/autocomplete-min.js"></script> <!-- APP JAVA SCRIPTS --> <script type="text/javascript" src="../script/myCoolApp/myCoolApp.js" ></script> <script type="text/javascript" src="../script/myCoolApp/stack.js" ></script> <script type="text/javascript" src="../script/myCoolApp/testcase/testcase.js"></script> <script type="text/javascript" src="../script/myCoolApp/testcase/default-data.js" ></script> <script type="text/javascript" src="../script/myCoolApp/testcase/data-structs.js" ></script> <script type="text/javascript" src="../script/myCoolApp/testcase/ui-elements.js" ></script> </head> <body class="cf010"> <div id="wrap"> <div id="header"> <div id="main-header"> COOL APP </div> </div> <div id="main-body"> <div id="content"> <div class="col main"> <div id="main"> <form method="post" id="testcaseForm" class="typea" action=""> <fieldset> <legend>Test Case Builder</legend> <div id="tk1" class="tabcontrol"> <ul class="tabs"> <li class="first active"> <a href="#"> <span>General</span> </a> </li> <li class="last"> <a href="#"> <span>Parameters</span> </a> </li> </ul> <div id="tab0" class="tc-panel"> <dl class="cls9"> <dt> <label for="scenario">Choose Scenario:</label> </dt> <dd> <input type="text" id="scenario" name="scenario" class="text" /> <span id="scenarioToggle"></span> <div class="auto-complete" id="scenarioContainer"></div> </dd> <dt> <label for="ruleID">Choose Rule ID:</label> </dt> <dd> <input type="text" id="ruleID" name="ruleID" class="text" /> <span id="ruleIDToggle"></span> <div class="auto-complete" id="ruleIDContainer"></div> </dd> <dt> <label for="Test Case Name" accesskey="t"><span class="accesskey">T</span>est Case Name:</label> </dt> <dd> <input type="text" id="testCaseName" name="testCaseName" class="text" /> </dd> </dl> </div> <div id="tab1" class="tc-panel hidden"> <div class="toolbar" id="action-bar"> <ul> <li class="first"> <a title="select all" href="#" id="btmSelectAll" class="button"> <span>select all</span> </a> </li> <li> <a title="remove row" href="#" id="btmRemove" class="button"> <span>remove row</span> </a> </li> <li> <a title="undo last" href="#" id="btmRollBack" class="button disabled"> <span>undo last</span> </a> </li> <li class="last"> <a title="accept row" href="#" id="btmAccept" class="button disabled"> <span>accept row</span> </a> </li> </ul> </div> <div id="param.list" class="gridclip"> <table id='param.list.tbl' class='grid modela' > <caption>Test Case Summary</caption> <col/><col/><col/> <thead> <tr> <th class='hl center first'> <input class='grid-select-all' type='checkbox' /> <th> <th scope='col'>Row</th> <th scope='col'>Parameter</th> <th scope='col' class='last'>Value</th> </tr> </thead> <tfoot> <tr> <th scope='row'>Total</th> <td colspan='3'>2 parameters as Test Case input</td> </tr> </tfoot> <tbody id='param.list.tbl.body'> <tr class='odd'> <td class='rowcheck center first'> <input value='param1###value1' id='cb1' name='SelectedRows' class='grid-select-row' type='checkbox'/> </td> <td class='id'>1</td> <td>param1</td> <td class='last'>value1</td> </tr> <tr class='even'> <td class='rowcheck center first'> <input value='param2###value2' id='cb1' name='SelectedRows' class='grid-select-row' type='checkbox'/> </td> <td class='id'>2</td> <td>param2</td> <td class='last'>value2</td> </tr> <tr class='odd'> <td class='rowcheck center first' /> <td class='id'><em>new</em></td> <td> <dl class='clsTable'> <dt> <input type='text' id='param' name='param' class='text paramInput' /> </dt> <dd> <span id='paramToggle' /> </dd> <div class='auto-complete' id='paramContainer' /> </dl> </td> <td class='last'> <dl class='clsTable'> <dt> <input type='text' id='value' name='value' class='text valueInput' /> </dt> </dl> </td> </tr> </tbody> </table> </div> </div> </div> <!-- tabcontrol --> </fieldset> <div class="submit-box"> <input type="submit" name="formRun" id="formRun" class="form-save" value="Execute" accesskey="x" title="Run: Press Alt + [Shift] + x" /> <input type="submit" name="formSave" id="formSave" value="Save" accesskey="s" title="Save: Press Alt + [Shift] + s" /> <input type="submit" name="formLoad" id="formLoad" value="Load" accesskey="l" title="Load: Press Alt + [Shift] + l" /> <input type="submit" name="formCancel" id="formCancel" class="form-cancel" value="Cancel" accesskey="c" title="Cancel: Press Alt + [Shift] + c" /> </div> </form> </div> </div> </div> </div> </div> </body> </html> As you can see the following is pretty much a duplicate: <tr class='odd'> <td class='rowcheck center first'> <input value='param1###value1' id='cb1' name='SelectedRows' class='grid-select-row' type='checkbox'/> </td> <td class='id'>1</td> <td>param1</td> <td class='last'>value1</td> </tr> <tr class='even'> <td class='rowcheck center first'> <input value='param2###value2' id='cb1' name='SelectedRows' class='grid-select-row' type='checkbox'/> </td> <td class='id'>2</td> <td>param2</td> <td class='last'>value2</td> </tr> The relevant part of my stuts-config.xml file is: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE struts-config PUBLIC "-//Apache Software Foundation//DTD Struts Configuration 1.2//EN" "http://struts.apache.org/dtds/struts-config_1_2.dtd"> <struts-config> <data-sources /> <form-beans> <form-bean name="TestCaseForm" type="com.blahblah.mycoolapp.forms.TestCaseForm" /> </form-beans> <action-mappings> <action path="/pages/SaveTestCase" name="TestCaseForm" type="org.springframework.web.struts.DelegatingActionProxy" scope="request"> </action> </action-mappings> <message-resources parameter="MessageResources" /> </struts-config> I also use spring 2.56 (The relevant part being): <?xml version="1.0" encoding="UTF-8"?> <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans-2.5.xsd"> <bean name="/pages/SaveTestCase" class="com.blahblah.mycoolapp.actions.TestCaseBuilderSaveAction" /> </beans> My Java ActionForm class (from what I had learned off the net) is: package com.blahblah.mycoolapp.forms; import java.util.ArrayList; import java.util.List; import org.apache.struts.action.ActionForm; public class TestCaseForm extends ActionForm { private static final long serialVersionUID = 2352146257739099766L; private String scenario; private String ruleID; private String testCaseName; private List<String> SelectedRows = new ArrayList<String>() ; public String getScenario() { return scenario; } public void setScenario(String scenario) { this.scenario = scenario; } public String getRuleID() { return ruleID; } public void setRuleID(String ruleID) { this.ruleID = ruleID; } public String getTestCaseName() { return testCaseName; } public void setTestCaseName(String testCaseName) { this.testCaseName = testCaseName; } public List<String> getSelectedRows() { return SelectedRows; } public void setSelectedRows(int index, String value) { this.SelectedRows.add(value); } } The question is why do I get an empty SelectedRows in my TestCaseBuilderSave Action? Thanks all who have the patience to read such a long question... and (hopefully) thanks to all you potential saviors :)

    Read the article

  • Design patterns and multiple programming language

    - by Eduard Florinescu
    I am referring here to the design patterns found in the GOF book. First how I see it, there are a few peculiarities to design pattern and knowing multiple language knowledge, for example in Java you really need a singleton but in Python you can do without it you write a module, I saw somewhere a wiki trying to write all GOF patterns for JavaScript and the entries where empty, I guess because it might be a daunting task. If there is someone who is using design patterns and is programming in multiple programming languages supporting the OOP paradigm and can give me a hint on how should I approach design patterns that might help me in all languages I use(Java, JavaScript, Python, Ruby): Can I write good application without knowing exactly the GOF design patterns or I might need some of them which might be crucial and if yes which one, are they alternatives to GOF for specific languages, and should a programmer or a team make its own design patterns set?

    Read the article

  • Design patterns frequently seen in embedded systems programming

    - by softwarelover
    I don't have any question related to coding. My concerns are about embedded systems programming independent of any particular programming language. Because I am new in the realm of embedded programming, I would quite appreciate responses from those who consider themselves experienced embedded systems programmers. I basically have 2 questions. Of the design patterns listed below are there any seen frequently in embedded systems programming? Abstraction-Occurrence pattern General Hierarchy pattern Player-Role pattern Singleton pattern Observer pattern Delegation pattern Adapter pattern Facade pattern Immutable pattern Read-Only Interface pattern Proxy pattern As an experienced embedded developer, what design patterns have you, as an individual, come across? There is no need to describe the details. Only the pattern names would suffice. Please share your own experience. I believe the answers to the above questions would work as a good starting point for any novice programmers in the embedded world.

    Read the article

  • Should pathfinder in A* hold closedSet and openedSet or each object should hold its sets?

    - by Patryk
    I am about to implement A* pathfinding algorithm and I wonder how should I implement this - from the point of view of architecture. I have the pathfinder as a class - I think I will instantiate only one object of this class (or maybe make it a Singleton - this is not so important). The hardest part for me is whether the closedSet and openedSet should be attached to objects that can find the path for them or should be stored in pathfinder class ? I am opened to any hints and critique whatsoever. What is the best practice considering pathfinding in terms of design ?

    Read the article

  • Databinding to an Entity Framework in WPF

    - by King Chan
    Is it good to use databinding to Entity Framework's Entity in WPF? I created a singleton entity framework context: To have only one connection and it won't open and close all the time. So I can pass the Entity around to any class, and can modify the Entity and make changes to the database. All ViewModels getting the entity out from the same Context and databinding to the View saves me time from mapping new object, but now I imagine there is problem in not using the newest Context: A ViewModel databinding to a Entity, then someone else updated the data. The ViewModel will still display the old data, because the Context is never being dispose to refresh. I always create new Context and then dispose of it. If I want to pass the Entity around, then there will be conflicts between Context and Entity. What is the suggested way of doing this ?

    Read the article

  • Design patterns and multiple programming languages

    - by Eduard Florinescu
    I am referring here to the design patterns found in the GOF book. First, how I see it, there are a few peculiarities to design pattern and knowing multiple languages, for example in Java you really need a singleton but in Python you can do without it you write a module, I saw somewhere a wiki trying to write all GOF patterns for JavaScript and all the entries were empty, I guess because it might be a daunting task to do that adaptation. If there is someone who is using design patterns and is programming multiple languages supporting the OOP paradigm and can give me a hint on how should I approach design patterns. An approach that might help me in all languages I use(Java, JavaScript, Python, Ruby): Can I write good application without knowing exactly the GOF design patterns or I might need just some of them which might be crucial and if yes which one, are there alternatives to GOF for specific languages, and should a programmer or a team make their own design patterns set?

    Read the article

  • DI/IoC in Java for a .NET'er used to Castle.Windsor

    - by Ciddan
    Is there a Java DI container that works in a similar way to the most excellent Castle.Windsor container on the .NET side? The Java containers I've had a look at all seem to rely on annotations (Guice) within my services, which I don't dig all that much - I'd like to go POJO all the way if possible. Spring on the other hand can do without the annotations, but it requires a lot of XML. XML configuration != maintainability. One of the really nice things about Castle.Windsor is the wiring you're able to set up in code with Installers, auto wiring based on naming conventions and whatnot. Ideally the container should also support lifecycle management and configuration; i.e. registering components as transient, singleton, pooled etc. Another bonus would be support for interceptors. Any tips would be greatly appreciated.

    Read the article

  • How do game programmers design their classes to reuse in AI, network and play and pass mode?

    - by Amogh Talpallikar
    For a two player game where, your opponent could be on the network, CPU itself or near you where you would play turn by turn on the same machine. How do people design classes for re-use ? I am in a similar situation and have no experience in making such complex games. But here is what I have thought, If I am a player object , I should only be interacting with the GameManager or GameEngine Singleton , from which I will get various notifications about the game status. I dont care where and who my opponent is, this GameManager depending upon the game mode, will interact with gameNetworkManager , or AI tell me what the opponent played. I am not sure about the scenario where we play and pass [turn by turn on same machine]. Hoping for a brief but clear explanation or at least a link to a similar resource.:)

    Read the article

  • Accessing managers from game entities/components

    - by Boreal
    I'm designing an entity-component engine in C# right now, and all components need to have access to the global event manager, which sends off inter-entity events (every entity also has a local event manager). I'd like to be able to simply call functions like this: GlobalEventManager.Publish("Foo", new EventData()); GlobalEventManager.Subscribe("Bar", OnBarEvent); without having to do this: class HealthComponent { private EventManager globalEventManager; public HealthComponent(EventManager gEM) { globalEventManager = gEM; } } // later on... EventManager globalEventManager = new EventManager(); Entity playerEntity = new Entity(); playerEntity.AddComponent(new HealthComponent(globalEventManager)); How can I accomplish this? EDIT: I solved it by creating a singleton called GlobalEventManager. It derives from the local EventManager class and I use it like this: GlobalEventManager.Instance.Publish("Foo", new EventData());

    Read the article

  • Best way of accessing data on different pages

    - by Gaz83
    I'm looking for a way to load data into properties/variables etc and have this information accessible to all the pages of my app. I want the information to be loaded via a background thread to keep UI thread free. Some of the pages will have various properties of their controls binding to these global properties. Here is what I tried. Created a static class. All pages could access the data but can't bind. Changed the static class to a Singleton and used DependencyProperty's. All pages could access data and binding worked fine but cross-threading issues when accessing via background threads. I have read in various places on this subject but haven't really come up with the best method yet for my situation.

    Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >