Search Results

Search found 67891 results on 2716 pages for 'windows virtual pc'.

Page 62/2716 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

  • Windows 7 intermittently drops wired internet/lan connection.

    - by CraigTP
    In a nutshell, my Windows 7 Ultimate PC intermittently drops it's internet connection. Why? Background: My PC is wired to my ADSL modem/router which is directly connected to the phone line. I also have wireless connectivity turned on within the router for a laptop to connect wirelessly. Every few hours or so, when using my PC, I find I cannot access the internet and pages will not load. Eventually, Windows7 will update the network icon in the task-tray to show the exclamation mark symbol on the network icon. Opening up the Network And Sharing Centre will show the red cross between the "Multiple Networks" and "The Internet". Here's a picture of the "Network And Sharing Centre" (grabbed when everything was working!) As you can see, I'm running Sun's VirtualBox on this machine and that creates a Network connection for itself. This doesn't seem to affect the intermittent dropping (i.e. the intermittent drops occur whether the VirtualBox connection is in use or not). When the connection does drop, I cannot access any internet pages, nor can I access the router's web admin page at http://192.168.1.1/, so I'm assuming I've lost all local LAN access too. It's definitely not the router (or the internet connection itself) as my laptop, using the wireless connection (and running Vista Home Premium) continues to be able to access the internet (and the router's web admin pages) just fine. Every time this happens, I can immediately restore all internet and LAN access by opening Network Adapter page, disabling the "Local Area Connection" and then re-enabling it. Give it a few seconds and everything is fine again. I assume this is because, beneath the GUI, it's effectively doing an "ipconfig /release" then "ipconfig /renew". Why does this happen in the first place, though? I've googled for this and seen quite a few other people (even on MSDN/Technet forums) experiencing the same or almost the same problem, but with no clear resolution. Suggestions of turning off IPv6 on the LAN adapter, and ensuring there's no power management "sleeping" the network adapter have been tried but do not cure the problem. There does not seem to be any particular sequence of events that cause it to happen either. I've had it go twice in 20 minutes when just randomly browsing the web with no other traffic, and I've also had it go once then not go again for 2-3 hours with the same sort of usage. Can anyone tell me why this is happening and how to make it stop? EDIT: Additional information based upon the answer provided so far: Firstly, I forgot the mention that this is Windows 7 64 bit if that makes any difference at all. I mentioned that I don't think the VirtualBox network adpater is causing this problem in any way, and I also have VirtualBox installed on two other machines, one running Vista Home Premium and the other running XP. Neither of these machine experience the same network connectivity issues as the Windows 7 machine. The IP assignment for the Windows 7 machine is the same both before and after the "drop". I have a DHCP server on the router issuing IP Addresses, however my Windows 7 machine uses a static address. Here's the output from "ipconfig": Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.2(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Within the system's event logs, the only event that relates to the connection dropping is a "DNS Client Event" and this is generated after the connection has dropped and is an event detailing that DNS information can't be found for whatever website I may be trying to access, just as the connection drops: Log Name: System Source: Microsoft-Windows-DNS-Client Event ID: 1014 Task Category: None Level: Warning Keywords: User: NETWORK SERVICE Description: Name resolution for the name weather.service.msn.com timed out after none of the configured DNS servers responded. The network adapter chipset is Realtek PCIe GBE Family Controller and I have confirmed that this is the correct chipset for the motherboard (Asus M4A77TD PRO), and in fact, Windows Update installed an updated driver for this on 12/Jan/2009. The details of the update say that it's a Realtek software update from December 2009. Incidentally, I was still having the same intermittent problems prior to this update. It seems to have made no difference at all. EDIT 2 (1 Feb 2010): In my quest to solve this problem, I have discovered some more interesting information. On another forum, someone suggested that I should try running Windows in "Safe Mode With Networking" and see if the problem continues to occur. This was a fantastic suggestion and I don't know why I didn't think of it sooner myself. So, I proceeded to run in Safe Mode with Networking for a number of hours, and amazingly, the "drops" didn't occur once. It was a positive discovery, however, due to the intermittent nature of the original problem, I wasn't completely convinced that the problem was cured. One thing I did note is that the fan on my GFX card was running alot louder than normal. This is due to the fact that I have an ASUS ENGTS250 graphics card (http://www.asus.com/product.aspx?P_ID=B6imcoax3MRY42f3) which had a known problem with a noisy fan until a BIOS update fixed the issue. (See the "Manufacturer Response" here: http://www.newegg.com/Product/Product.aspx?Item=N82E16814121334 for details). Well, running in safe mode had the fan running (incorrectly) at full speed (as it did before the BIOS update), but with an (apparently) stable network connection. Obviously some driver was not loaded for the GFX card when in Safe Mode so this got me thinking about the GFX card (since the very noisy fan was quite obvious when running in Safe Mode). I rebooted into normal mode, and found that Nvidia had a very up-to-date new driver for my GFX card (only about 1 week old), so I downloaded the appropriate driver and installed it. After installation and a reboot, I was able to use my PC for an entire day with NO NETWORK DROPS!!! This was on Saturday. However, on the Sunday, I also had my PC for pretty much the entire day and experienced 2 network drops. No other changes have been made to my PC in this time. So, the story seems to be that updating my graphics card drivers seems to have improved (if not completely fixed) the issue, however, I'm still searching for a proper fix for this problem. Hopefully, this information may help anyone who may have additional ideas as to why this problem is occuring in the first place. (And why does new GFX card drivers have anything to do with the network?) I appreciate everyone's feedback so far. However, I'll have to ask once more if anyone has any further ideas of how to fix this particular problem? Thanks in advance.

    Read the article

  • "Requested registry access is not allowed." on Windows 7 / Vista

    - by Trainee4Life
    I'm attempting to write a key to Registry. It works on Windows XP, but fails on Windows 7 / Vista. The code below throws a Security Exception with description "Requested registry access is not allowed." RegistryKey regKey = Registry.LocalMachine.OpenSubKey("SOFTWARE\\App_Name\\" + subKey, true); I realise that this has to do with the UAC settings, but I couldn't figure out an ideal workaround. I don't want to fork out another process, and may be don't even want to request for any credentials. Just want it to work the same way as on Windows XP. I have modified the manifest file and removed requestedExecutionLevel node. This seems to do the trick. Is there any other possible workaround, and are there any serious flaws with the "manifest" solution?

    Read the article

  • How to activate Win XP from Windows 7 compatibility mode on MacOS Parallels 5

    - by Ben Hammond
    I am running Parallels Desktop 5.0.9344 for Mac. I am running Mac OS 10.6.3 10D2094 I have bought a retail copy of Window 7 professional specifically because I need the XP compatibility. Windows 7 is installed and working. I have problems with the XP activation Windows7 'Virtual PC' does not run under Parallels (strange error about Server Execution failed 0x80080005). I have used the Parallels Transporter to convert the "Windows XP Mode Base.vhd" file into a parallels Virtual Machine. This copy of XP now starts normally, however it records itself as unregistered. There was a KEY.txt file in the same directory as the .vhd file; although this file contains a valid-looking activation key, it does not appear to activate the instance of XP. I have also tried to enter the Win7 activation key; this does not work either. I have tried calling the two phone numbers; an automated system asked me to enter 56 digits through the telephone and then accused me of being a pirate. I believe it may be possible to install Win7 via Bootcamp, start WinXP under Virtual PC, activate it and then import this activated .vhd into Parallels; but that seems a long way round, and is far from certain. What can I do to get WinXP running under Mac Parallels Desktop ?

    Read the article

  • Simulated NAT Traversal on Virtual Box

    - by Sumit Arora
    I have installed virtual box ( with Two virtual Adapters(NAT-type)) - Host (Ubuntu -10.10) - Guest-Opensuse-11.4 . Objective : Trying to simulate all four types of NAT as defined here : https://wiki.asterisk.org/wiki/display/TOP/NAT+Traversal+Testing Simulating the various kinds of NATs can be done using Linux iptables. In these examples, eth0 is the private network and eth1 is the public network. Full-cone iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to-source iptables -t nat -A PREROUTING -i eth0 -j DNAT --to-destination Restricted cone iptables -t nat POSTROUTING -o eth1 -p tcp -j SNAT --to-source iptables -t nat POSTROUTING -o eth1 -p udp -j SNAT --to-source iptables -t nat PREROUTING -i eth1 -p tcp -j DNAT --to-destination iptables -t nat PREROUTING -i eth1 -p udp -j DNAT --to-destination iptables -A INPUT -i eth1 -p tcp -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -i eth1 -p udp -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -i eth1 -p tcp -m state --state NEW -j DROP iptables -A INPUT -i eth1 -p udp -m state --state NEW -j DROP Port-restricted cone iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to-source Symmentric echo "1" /proc/sys/net/ipv4/ip_forward iptables --flush iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE --random iptables -A FORWARD -i eth1 -o eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT What I did : OpenSuse guest with Two Virtual adapters - eth0 and eth1 -- eth1 with address 10.0.3.15 /eth1:1 as 10.0.3.16 -- eth0 with address 10.0.2.15 now running stund(http://sourceforge.net/projects/stun/) client/server : Server eKimchi@linux-6j9k:~/sw/stun/stund ./server -v -h 10.0.3.15 -a 10.0.3.16 Client eKimchi@linux-6j9k:~/sw/stun/stund ./client -v 10.0.3.15 -i 10.0.2.15 On all Four Cases It is giving same results : test I = 1 test II = 1 test III = 1 test I(2) = 1 is nat = 0 mapped IP same = 1 hairpin = 1 preserver port = 1 Primary: Open Return value is 0x000001 Q-1 :Please let me know If any has ever done, It should behave like NAT as per description but nowhere it working as a NAT. Q-2: How NAT Implemented in Home routers (Usually Port Restricted), but those also pre-configured iptables rules and tuned Linux

    Read the article

  • "Error: Unknown error" when trying to start virtual machine from VMware server

    - by slhck
    Problem We are running VMware Server 2.0.0 build-116503 on a Ubuntu 10.04 LTS server. There is a virtual machine installed, running Lotus Domino on Windows Server 2003. Ever since a sudden power failure last week, the virtual machine won't properly start up. When I run the command: vmrun -T server -h https://127.0.0.1:8333/sdk -u root -p jk2x2208 start "[standard] lotus/test.vmx" … after 30 seconds it displays: Error: Unknown error That's about everything I get. I know the command is right, since that's what we've used all the time. This has happened last Saturday after a scheduled backup shutdown, and somehow I was able to start it again. This week, it happened again, and I can't get it back up. Occasionally, I also get: Error: Cannot connect to the virtual machine When I get this, and I run the start command, it seemingly works. Why is this so random? Which configuration could have been messed up? What I've tried / other info I already shut down VMware itself with /etc/init.d/vmware stop. This works. I tried to start VMware again with /etc/init.d/vmware start. It complains that it's "not configured", which is why I had to rm /etc/vmware/not_configured, and then try to start again. There have been no software updates on the machine, and no configuration changes

    Read the article

  • Windows 7 XP Mode-Program not ending properly

    - by iceman33
    We currently have recently have implemented a few new machines to our network with Windows 7 Enterprise 64-bit installed on them. We have a program that is incompatible with Windows 7 right now and we have it installed on the Windows XP Mode that we have setup on there. There is a shortcut that is on the desktop to have it work with integration services and that part is working successfully. Occasionally, this program will stop working over the server on which it connects to has to get rebooted and the program has to get closed out. However, that process that is in the task manager doesn't seem to close out properly. So in order to correctly get the program shut down, we have to make the users log back into xp mode and do a Ctrl+Alt+Delete to kill the process or have to go back into the machine to perform a restart. I was wondering if anyone has come across a way within XP Mode yet that when the virtual machine goes into hibernation mode that it would shut down all processes or if when restarting the virtual machine your normal machine that it would shut everything down in the virtual XP mode as well and not just keep that program running? Any help would be greatly appreciated.

    Read the article

  • Windows: disable remote access of local drive, even by domain admin

    - by Matt
    We have a network of Windows 7 PCs that are managed as part of a domain. What we want is for the domain admin to be unable to view the PC's local drive (C:) unless he is physically at the PC. In other words, no remote desktop and no ability to use UNC. In other words, the domain admin should not be allowed to put \\user_pc\c$ in Windows Explorer and see all the files on that computer, unless he is physically present at the PC itself. Edit: to clarify some of the questions/comments that have come up. Yes, I am an admin---but a complete Windows novice. And yes, for the sake of this and my similar questions, it is fair to assume that I am working for someone who is paranoid. I understand the arguments about this being a "social problem versus a technical problem", and "you should be able to trust your admins", etc. But this is the situation in which I find myself. I'm basically new to Windows system administration, but am tasked with creating an environment that is secure by the company owner's definition---and this definition is clearly very different from what most people expect. In short, I understand that this is an unusual request. But I'm hoping there is enough expertise in the ServerFault community to point me in the right direction.

    Read the article

  • Deploying multiple identical copies of a virtual machine for compute tasks

    - by Reid
    I have a compute task which has a large number of library dependencies. I would like to deploy it on some of my company's large Linux clusters, where I do not have root. I could probably track down, compile, and install the right versions of all the libraries, but this looks to be quite tedious and would have to be repeated if I deployed it again somewhere else. On the other hand, it's pretty easy to install on current Ubuntu. This led me to wonder about a virtual machine approach. Could I put together a virtual machine which booted up, ran the computation (with parameters from and results to the host), and then shut down? In other words, I'd like a command like this that I could run on the host: $ ./run-vm --ram N --task /path/on/host/foo.sh --results /another/host/dir/ This would boot the VM, run foo.sh, and put the (relatively small) results of the computation in /another/host/dir/. It's important to start up many instances of the VM simultaneously, both on a single node and multiple nodes of the cluster. So it would be nice if I didn't have to make many copies of the VM virtual disk and metadata. As the task instances are completely independent, the VMs would not need any network support once deployed, or any outside communications beyond reading and writing the host filesystem. Is this possible, and if so, how might I go about doing it? Are there assumptions I've made above which are bogus?

    Read the article

  • Windows Explorer Keeps On Crashing

    - by Josefvz
    Hey Folks. I'm lost... I'm using Windows 7 Ultimate 64bit. My Pc is up to date(windows updates) and I've used Winutilities to scan my registry. My explorer.exe keeps on crashing. Just randomly it seems. I don't even need to be doing anything particular. I do have experience with pc in general as I'm a software developer. I know you will require additional info, but i don't know what, so just leave a comment and I'll update. Additional info I think i should also mention that explorer is the only app that crashes on my pc. The crash report i got now: Description: A problem caused this program to stop interacting with Windows. Problem signature: Problem Event Name: AppHangB1 Application Name: explorer.exe Application Version: 6.1.7600.16450 Application Timestamp: 4aebab8d Hang Signature: 0a1b Hang Type: 16897 OS Version: 6.1.7600.2.0.0.256.1 Locale ID: 7177 Additional Hang Signature 1: 0a1bdae38ae7300761c516c4416d992c Additional Hang Signature 2: 1c51 Additional Hang Signature 3: 1c518a49cc7d37652d26c521e96f66c2 Additional Hang Signature 4: 521e Additional Hang Signature 5: 521e607ec26a72aab4ae5a7126916ef3 Additional Hang Signature 6: e5e3 Additional Hang Signature 7: e5e3ca31dad607fa7b858ff5ea5c0fa9

    Read the article

  • virtual web folder served by PHP script

    - by Martin
    I am trying to configure my apache to be able to display (virtual) pages like: mywebpage.com/something1 mywebpage.com/something2 mywebpage.com/folder/something3 I would like these "somethingX" and "folder" folders to be only virtual, not physical directories. For a start it would be great to send all requests to mywebpage to one PHP script which will somehow receive the original path information (there is some SERVER array as far as I know) and call necessary PHP functions (so far I use addresses like mywebpage.com/index.php?page=blabla&otherparameters=values...). Is that possible? I am struggling with different combination, currently I am with following file in /etc/apache2/conf.d/something.conf (not working of course). What is the correct way to proceed? Thanks. <Location /myweb> SetHandler my-handler Action my-handler /srv/www/htdocs/myweb/product.php virtual </Location> My pages are in /srv/www/htdocs/myweb. I tried with Location, with Directory, with Action and SetHandler, with AddHandler... ;-) Some configurations were ignored, some caused "object not found" with nothing relevant in error log.

    Read the article

  • (Windows) How to lock all applications (explorer, task manager etc.) and make only the browser activ

    - by Unni
    I'm trying to run only the browser in the system - locking access to everything else. Only the supervisor can resume the normal functioning of the system after giving a password. This kind of activity is usually done by virus. Disabling the registry for Task manager etc. Does anyone know of any source available that does this? I might be able to pull it off in Windows XP. But have anyone tried this in Windows 7 ? The aim is to to emulate the Chrome OS on Windows. Only the browser. Nothing else.

    Read the article

  • Virtual Server HDD shrinks without apparent reason

    - by Christian
    We have a virtual hosted Linux server, and in the last few months every now and then the HDD shrinks from 400GB down to the exact byte count that is in use. All existing data can be downloaded and displayed without a problem, but we can't upload or edit any files because of the "full" hard drive. Here is a screenshot, where "size" should be 400GB: This has happened twice before, and again today. The last times, when I reported the issue to the host, they said "that isn't possible, you must be doing it wrong", but soon after the call, the problem vanished without us doing anything, so I suppose that they have some kind of problem they're not willing to admit. Even after the fact, they acted like nothing was wrong and wrote me a mail in which they explained that I can use "df -h" to view available disk space (well duh, how do you think I noticed this particular issue?). Questions about if and what they had done were ignored. It has happened around the 25th to 28th of the month, so I suspect that they might have a cronjob running every 30 days or so which wreaks havoc with some VM configs. I just want to understand the problem, but the host support hasn't been very helpful in that regard. I have tried Googling the issue, but any combination of search terms I can come up with just gives me tutorials on how to change HDD size in a virtual machine. a) What could be the cause of shrinking HDD size in a Ubuntu 12.04.3 LTS server? Could there be anything in our virtual machine or is it more likely to be an issue with the vm host? b) Can I do anything about it without needing to contact the host's support? c) Is there anyway I can prevent this from happening at all?

    Read the article

  • Microsoft Dev Centre accounts

    - by Phil Murray
    Looks like Microsoft is offering a special offer of 95% of the yearly subscription for the Phone Dev Centre (I didn't say anything about desperate). What I was wondering is do you need a seperate account to publish to the Windows Phone app centre and the Windows App Centre? Also I heard some horror stories about the time it takes to get application published on the Windows phone marketplace, does anyone have any experience with this? Windows Phone Dev Centre Windows App Dev Centre

    Read the article

  • Getting Ubuntu on Bootloader after formatting

    - by Muhammad Badi
    I've been running Windows XP on a desktop machine (C:/) and installed Ubuntu 12.04 (D:/) and Windows bootloader was able to recognize Ubuntu when I turn on the computer. Months later, I've formatted drive C:/, removed XP, and then installed Windows 7 but sadly, Ubuntu is not showing in the boot menu as it used to be presented: Windows 7 Ubuntu How to get it back on boot list? NOTE: Please note that installing Ubuntu was done from inside Windows XP with wubi.exe

    Read the article

  • Run windows and ubuntu parallely

    - by user3185902
    I have read about Virtualbox using which we can run both windows and ubuntu parallely, but it seems that for this we have to make one host and install the other one using Virtualbox in it. (Please correct me if wrong) I am already using both ubuntu and windows on my pc (dual boot) and I want to run the already existing ones parallely instead of installing one of them again (don't want to install the softwares again). So, is there a way by which I can do this? Thanks

    Read the article

  • in-place upgrade Windows Server Standard Edition 2003 to Windows Server Enterprise/Datacentre Editio

    - by Systech
    I recently asked a question about upgrading from 2003 to 2008, but i realised this is a lot harder to do, the only reason i want to upgrade is to have increase the RAM Windows 2003 Standard Edition R2 only supports 4GB Windows 2003 Enterprise Edition R2 supports up to 32GB Windows 2003 Datacentre Edition R2 supports up to 64GB So basically i need to do an in-place upgrade to either Enterpirse or Datacentre without losing any data is this possible? Also is one easier to upgrade to then the other?

    Read the article

  • upgrade from windows 2008 server CORE to full windows 2008 server

    - by laurens
    Possible Duplicate: Install GUI on Windows Server 2008 Core As I've seen there is not really a topic about this here... My question: Is there any means to upgrade from windows 2008 server CORE to full windows 2008 server? The server is used as Hyper-V Host machine. On the internet mostly I find: "no you'll have to reinstall" But maybe there's a workaround? Thanks in advance

    Read the article

  • Windows Clients: Windows or Linux Domain Controller?

    - by Ramon Marco Navarro
    I'm planning to set up a domain controller for our small computer laboratory. I'm a little confused as to what operating system to use for our domain controller. What's in the lab: The lab has 25 units running a mix of Windows 7 and Windows XP. The domain controller will only have 2GB of RAM running a C2D E7200. (Is this enough?) What we want: The Domain Controller will also be running a git server. The Domain Controller will also be used as a general development machine (mostly Java, PHP). A way to centralize the updates for the windows clients, so that they won't have to download the same patches from the remote site. The machines would just query them from the local domain controller and get the updates from there. Our head recommended that I virtualize a Windows Server 2008 system under a Linux host and use the former as a domain controller and the latter for development or the other way around. A comparison of the advantages and disadvantages of using a Linux distribution or Windows Server 2008 in this situation would also be appreciated. As you may have noticed by now, I'm kinda new to setting up a domain so I hope you guys will be able to help me. Thank you.

    Read the article

  • I cannot install KB 968211 "this update is not applicable to your computer"

    - by Kirby
    I have Windows 7 Professional SP1..64bit... and yes windows genuinely activated. I want to install Windows Media player 12 and it seems i require the "Media Feature pack"... I can't seem to find a good install. I've tried at least 4 of them.. both 64bit and x86. I've googled the bejesus out of this... https://www.microsoft.com/download/en/details.aspx?id=16546 Any help would be greatly appreciated. TIA, Kirby

    Read the article

  • Windows xp mapped drives disconnect from Windows 7 on Peer to Peer network

    - by Kathryn Codo
    I have a 5 user peer to peer network. 2-XP machines, 3- Windows 7 machines and a Windows 7 machine acting as the file server. I have NO issues with the Windows 7 machines staying connected via the mapped drives to the "server". However, once a day the 2 XP machines will not connect to the Windows 7 machine "server" via the mapped drives. I must restart the "server" in order to see the server and access the files via the mapped drives or Explorer. I have tried the persistent : yes command in NET USE, on the XP machines and also setting a static IP address on the "server". I've turned the firewall off on the "server:, no difference so I turned the firewall back on. No interruption occurs with the internet when this happens, just can't see the server. Again, the Windows 7 users are unaffected. I have gone into the advanced network settings on the "server" and added read/write permissions for Everyone as well as the users of the XP machines. I have double checked that we are all on the same WORKGROUP. I'm at a loss. It seems to happen around mid-day and I've not been able to find any activity that is happening at this time (Like someone plugging in a thumbdrive). Any suggestions would be greatly appreciated as my client is running old XP software he no longer has the disks for and needs for his engineering firm.

    Read the article

  • Linux clients and Windows Servers can connect but not windows clients

    - by Mustafa Ismail Mustafa
    This is driving me insane because I can't make head or tails of it. We have two DCs (W2K3 SP1) and I'v tried this once on each machine as a sanity check. DHCP is being served by either one of the machines and all machines get an address no problem. The servers can connect/ping/browse to the www and so can all our linux clients. But NONE of our windows clients (all windows 7). I can do anything within the network, I can even ping the firewall/router but nothing from the windows clients is leaving the confines of our subnet. I don't get it. The linux and windows clients are both served from the same DHCP server, the gateway is the same, everything is the same. Anyone care to take a shot at how to resolve this? I tried adding explicit routes at the clients, but still no go. TIA SMIM

    Read the article

  • A minimal Linux distribution for my ASUS EEE PC

    - by Andrioid
    I recently bought myself a ASUS EEE 1000HE and I intend to use it for note-taking and light browsing at the University. The machine has a 10" screen so the interface needs to be very compact. I've already tried: EEEbuntu: Very nice driver support and out of the box experience. But I feel that it is too slow booting and the general experience is too heavy in my opinion. Moblin 2: Looks very cool, boots just fine but is way too unstable to use. Also find it annoying that I can't find hotkey documentation anywhere. Any Netbook OS recommendation welcome (although those specific to my model would be great). There is an entire jungle of distributions out there, so if you've been on a safari, please share your experience.

    Read the article

  • NX Client for Windows 7 Opens Remote Desktop in Multiple Windows

    - by Corey Kennedy
    What I'm trying to do: access my Ubuntu desktop remotely via NX Client on my Windows 7 laptop. My environment: server: Ubuntu 10.10 on AMD 1Ghz/512MB RAM PC client: Windows 7 on ThinkPad sl510 Software: server is running NXServer 3.4.0. Using xfce4 window manager. Laptop is using NXClient for Windows In my NX Client "Desktop" settings I've selected "Unix" and "Custom" for OS and environment. I've also specified "startxfce4" as the application to launch when NX connects. I am able to authenticate an NX session on my laptop. By this I mean, I can start the client on my laptop, enter credentials for my Linux user, and NX establishes a connection to the server and attempts to open a remote desktop window. The problem, though, is that this remote desktop is "fragmented" into many Windows. One window will display the bulk of my desktop (complete with desktop icons for "Home," "File System," and "Trash") while another window will contain the taskbar, and another window will contain the application strip. I can select each of these Windows individually, but I cannot click on any objects within them. I've searched Super User, Ubuntu Forums, NX help, Server Fault, and tried many Google searches - none have turned up another case of this particular problem. I'm stumped. Does anyone have any suggestions for what I might try? I'm guessing the problem has to do with my xfce config files, but I've only just setup this server - it's been a long time since I've used Linux and there's a lot I just don't know. What I am NOT trying to do: use Desktop sharing from Ubuntu, whereby I VNC into a desktop that I've already established on the server. I am trying to configure this Linux box as a headless server that I can stash someplace out-of-the-way in my house, then interact with through my laptop. I don't want to have a monitor or keyboard connected to the Linux box. Thanks for your help!

    Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >